fibre optics communication

7/31/2019 Fibre Optics Communication

1/21

FIBER OPTICSCOMMUNICATION

Presented by

NIKHILKUMAR. A. JAIN VISHAL.K.DHARAMDASANI

[email protected] [email protected]

II SEMESTERDEPARTMENT OF

ELECTRONICS AND COMMUNICATION ENGINEERING


2/21

GOGTE INSTITUTE OF TECHNOLOGY

UDYAMBAG, BELGUAM,KARNATAKA-590008.

CONTENTS...

Abstract

1.0 Introduction

1.1 What is Fiber Optics Communication?

1.2 Invention of Fiber Optics

1.3 Principal

2.0 Types of Optical Fibers

3.0 The Fiber Optics Data Communications link, End-to-End

4.0 Fiber Optics Communication Networks

4.1 Asynchronous Transfer Mode (ATM)

4.2 Integrated Services Digital Network (ISDN)

4.3 Ethernet

5.0 Areas of application

6.0 Merits

7.0 Demerits

8.0 Figures

9.0 Conclusion


3/21

10.0 References

ABSTRACT:

Our current age of technology is the result of many brilliant inventions and

discoveries, but it is our ability to transmit information, and the media we use to do it,

that is perhaps most responsible for its evolution. Progressing from the copper wire of a

century ago to today's fiber optic cable, our increasing ability to transmit more

information, more quickly and over longer distances has expanded the boundaries of our

technological development in all areas. An optical fiber communication is a transmission

medium designed to transmit digital signals in the form of pulses of light using optical

fibers. In its simplest terms, fiber optics is a medium for carrying information from one

point to another in the form of light. Unlike the copper form of transmission, fiber optics

is not electrical in nature.

Today's low-loss glass fiber optic cable offers almost unlimited bandwidth and

unique advantages over all previously developed transmission media.

In our treatise we explain the concept of fiber optics, its principle, fiber optics

data communication link, end-to-end. This article discusses these standards and


4/21

protocols, including ATM (Asynchronous Transfer Mode) Ethernet, ISDN (Integrated

Service Data Interface) and areas of application.

Word count: 194

INTRODUCTION:

1.1 What is Fiber Optics Communication?

A transmission medium designed to transmit digital signals in the form of pulses

of light. These pulses of light are transferred through the optical fibers. The transmission

media is the fiber optics itself. They guide visible and infrared light over long distances.

The optical fiber made up of an insulating material like glass, plastic etc. Fiber Optics

doesn't suffer from either line of sight or absorption under normal circumstances. Fiber

optic systems use a laser beam fired into a special glass or plastic fiber with a transparent

core. The fiber is designed to allow light to be transmitted along its length. It is specially

made to reflect light that reaches the outer edge of its core, and gently deflect the light

wave back to the center of the fiber. Thus, the light signal can be bent around corners.

The fiber is sealed, thus preventing water from getting in the way. These fibers are tiny.

Several fibers together are the width of a human hair, and each fiber can carry thousands

of connections (refer figure1.1a). Telecommunications companies use fiber optics most

frequently. Most fiber optic cable is buried in the ground, so water sometimes creeps in

and causes attenuation, but this is increasingly rare. Because fiber optics are so reliable,


5/21

and difficult to disrupt (it practically takes a backhoe to stop it), they are the most popular

form of long distance communication in use today.

The optical fiber construction: (refer figure 1.1b)

CORE its made of glass.

CLADDING - made of glass.

Plastic coating.

1.2 Invention of optical fiber

British physics John Tyndall nearly 120 years ago demonstrated

experimentally that light could be guided along a curved steam of water employing

optical phenomena of total internal reflection. Based on this concept the first glass fibers

were made in 1920s but the concept of cladding made guiding of light practical with

limited success in 1950.

It is the invention of lasers in1960 by Maiman, which created a sensation in

optical communication because of its high coherence property. The optical frequencies

are of order of 5x1014Hz,as compared to the frequencies of up to 10 10 Hz employed in

electric communication such as TV, radar, and microwave links. This indicates an

increase of information capacity 104 times in optical range.

In recent years it has become apparent that fiber optics are steadily replacing

copper wire as an appropriate means of communication signal transmission. They span

the long distances between local phone systems as well as providing the backbone for


6/21

many network systems. Other system users include cable television services, university

campuses, office buildings, industrial plants, and electric utility companies.

Principle

Think of a fiber cable in terms of very long cardboard roll (from the inside roll of

paper towel) that is coated with a mirror. If you shine a flashlight in one you can see light

at the far end - even if bent the roll around a corner.

Light pulses move easily down the fiber-optic line because of a principle known as

total internal reflection2. This principle of total internal reflection states that when the

angle of incidence exceeds a critical value, light cannot get out of the glass; instead, the

light bounces back in. When this principle is applied to the construction of the fiber-

optic strand, it is possible to transmit information down fiber lines in the form of light

pulses. (Refer figure 1.3a).

2.0 Types of optical fiber

1.Step Index Multimode Fiber(refer figure 2.0a)o Bandwidth - 20 MHz

o Core diameter - 100-250 microns

2.Graded Index Multimode Fiber (refer Figure2.0c)

o Bandwidth - 800 MHz



7/21

3.Step Index Single Mode Fiber (refer Figure 2.0b)

o Bandwidth - 5 GHz


3.0 The Fiber Optic Data Communications Link, End-to-End

This shows the simple fiber optic data link for the premises environment. This is the

basic building block for a fiber optic based network.

Model of simple fiber optic data link

Fiber optic transmission uses the same basic elements as copper-based

transmission systems: A transmitter, a receiver, and a medium by which the signal is

passed from one to the other, in this case, optical fiber.


8/21

TRANSMITTER:

The transmitter uses an electrical interface to encode the use information through AM,

FM or digital modulation. A laser diode or an LED does the encoding to allow an

optical output of 850 nm, 1310 nm, or 1550 nm (typically). Light Sources

There are two main light sources used in the field of fiber optics.

1. (LDs) Light Emitting diodes (LEDs)

2. Laser Diodes

Light Emitting Diodes:

An LED is a p-n junction diode in a transparent capsule usually with a lens

to let the light escape and to focus it. LED's can be manufactured to operate at 850

nm, 1300 nm, or 1500 nm. These wavelengths are all in the infrared region.

LED's have a typical response time of 8 ns, a line width of 40 nm, and an output

power of tens of microwatts.


9/21

Figure of LED

Laser Diodes:

A laser diode is an LED with two important differences

1) The operating current is much higher in order to produce optical gain.

2) Two of the ends of the LD are cleaved parallel to each other. These ends act as

perfectly aligned mirrors which reflect the light back and forth through the gain

medium in order to get as much amplification as possible.

The typical response time of a laser diode is 0.5 ns. The line width is around 2

nm with a typical laser power of 10's of mill watts. The wavelength of a laser diode can

be 850 nm, 1300 nm, or 1500 nm.


10/21

Figure of Laser Diode

RECEIVER:

The receiver uses either a PIN photodiode or an APD to receive the optical signal

and convert it back into an electrical signal. A data demodulator converts the data back

into its original electrical form. These elements comprise the simplest link, but other

elements may also appear in a fiber optic transmission

Long distance fiber optic transmission leads to further system complexity. Many

long-haul transmission systems require signal regenerators, signal repeaters, or optical

amplifiers such as EDFAs in order to maintain signal quality. System drop/repeat/add

requirements, such as those in multichannel broadcast networks, further add to the fiber

optic system, incorporating multiplexes, couplers/splitters, signal fan outs, dispersion

management equipment, remote monitoring interfaces, and error-correction components.

4.0 Fiber Optic Communications Networks

All networks involve the same basic principle: information can be sent to, shared

with, passed on, or bypassed within a number of computer stations (nodes) and a master


11/21

computer (server). In addition to various topologies for networks a number of standards

and protocols have been developed, each with their own advantages, topologies, and

medium requirements. This discusses these standards and protocols, including: ATM,

Ethernet & ISDN.

4.1 Asynchronous Transfer Mode (ATM)

Asynchronous transfer mode (ATM) is widely deployed as a network backbone

technology. This technology integrates easily with other technologies, and offers

sophisticated network management features that allow signal carriers to guarantee

Quality Of Service (QOS). ATM may also be referred to as cell relay because the

network uses short, fixed length packets or cells for data transport. The information is

divided into different cells, transmitted, and re-assembled at the receiving end. Each cell

contains 48 bytes of data payload as well as a 5-byte cell header. This fixed size ensures

that time critical voice or video data will not be adversely affected by long data frames or

packets.

ATM organizes different types of data into separate cells, allowing network users

and the network itself to determine how bandwidth is allocated. This approach works

especially well with networks handling burst data transmissions. Data streams are then

multiplexed and transmitted between end user and network server and between network

switches. These data streams can be transmitted to many different destinations, reducing

the requirement for network interfaces and network facilities, and ultimately, overall cost

of the network itself.


12/21

Connections for ATM networks include Virtual Path Connections (VPCs), which

contain multiple Virtual Circuit Connections (VCCs). Virtual circuits are nothing more

than end-to-end connections with defined endpoints and routes, but no defined bandwidth

allocation. Bandwidth is allocated on demand as required by the network. VCCs carry a

single stream of contiguous data cells from user to user. VCCs may be configured as

static, Permanent Virtual Connections (PVCs) or as dynamically controlled Switched

Virtual Circuits (SVCs). When VCCs are combined into VPCs, all cells in the VPC are

routed the same way, allowing for faster recovery of the network in the event of a major

failure.

While ATM still dominates WAN backbone configurations, an emerging

technology, Gigabit Ethernet, may soon replace ATM in some network scenarios,

especially in LAN and desktop scenarios. A discussion of Ethernet follows.

4.2 Integrated Services Digital Network (ISDN)

ISDN has been designed to replace the standard telephone system and provide

greater numbers of digital services to telephone customers, such as digital audio,

interactive information services, fax, e-mail, and digital video. ISDN uses asynchronous

transfer mode, which can handle data transmission in both connection-oriented, and

packet schemes. As with regular telephone lines, the user must pay a fee for use of the

line. Basic rate ISDN offers two simultaneous 64 kb/s data channels as well as a 16 kb/s


13/21

carrier channel for signaling and control information. The combined data rate, 128 kb/s,

allows for videoconferencing capabilities. Multiple ISDN-B connections further increase

the data rate and the transmission quality. Primary rate ISDN (PRI) offers 30 channels (of

64 kb/s each), giving a total of 1920 kb/s. As with BRI, each channel can be connected to

a different destination, or they can be combined to give a larger bandwidth. These

channels, known as bearer or B channels, give ISDN tremendous flexibility.

The original version of ISDN employs base band transmission. Another version,

called B-ISDN, uses base band transmission and is able to support transmission rates of

1.5 Mb/s. B-ISDN requires fiber optic cables and is not yet widely available.

4.3 Ethernet

Ethernet began as a laboratory experiment for Xerox Corporation in the 1970s.

Designers intended Ethernet to become a part of the Office of the future, which would

include personal computer workstations. By 1980, formal Ethernet specifications had

been devised by a multi-vendor consortium. Widely used in todays LANs, Ethernet

transmits at 10 Mb/s using twisted-pair coax cable and/or optical fiber. Fast Ethernet,

transmits at 100 Mb/s, and the latest developing standard, gigabit Ethernet, transmits at

1,000 Mb/s or 1 Gb/s. Figure shown below illustrates the basic layout of an Ethernet

network.
http://www.fiber-optics.info/articles/telecom-nets.htm#Figure_1http://www.fiber-optics.info/articles/telecom-nets.htm#Figure_1


14/21

Figure: basic layout of an Ethernet Network

The formal Ethernet standard known as IEEE.802.3 uses a protocol called Carrier

Sense Multiple Access with collision detection (CSMA/CD)5. This protocol describes the

function of the three basic parts of an Ethernet system: the physical medium that carries

the signal, the medium access control rules, and the Ethernet frame, which consists of a

standardized set of bits used to carry the signal. Ethernet, fast Ethernet, and gigabit

Ethernet all use the same platform and frame structure.

Ethernet users have three choices for physical medium. At 1 to 10 Mb/s, the

network may transmit over thick coaxial cable, twisted-pair coax cable or optical fiber.

Fast 100 Mb/s Ethernet will not transmit over thick coax, but can use twisted pair or

optical fiber as well. Gigabit Ethernet, with greater data rate and longer transmission

distance, uses optical fiber links for the long spans, but can also use twisted-pair for short

connections.

CSMA/CD represents the second element, the access control rules. In this

protocol, all stations must remain quiet for a time to verify no station in the network is


15/21

transmitting before beginning a transmission. If another station begins to signal, the

remaining stations will sense the presence of the signal carrier and remain quiet. All

stations share this multiple access protocol. However, because not all stations will receive

a transmission simultaneously, it is possible for a station to begin signaling at the same

time another station does. This causes a collision of signals, which is detected by the

station speaking out of turn, causing the station to become quiet until access is awarded,

at which time the data frame is resent over the network.

The final element, the Ethernet frame, delivers data between workstations based

on a 48-bit source and destination address field. The Ethernet frame also includes a data

field, which varies in size depending on the transmission, and an error-checking field,

which verifies the integrity of the received data. As a frame is sent, each workstation

Ethernet interface reads enough of the frame to learn the 48-bit address field and

compares it with its own address. If the addresses match, the workstation reads the entire

frame, but if the addresses do not match, the interface stops reading the frame.

Ethernet at all data rates has become a widely installed network for Local Area

Network (LAN), MAN, and Wide Area Network (WAN) applications. Its ability to

interface with Synchronous Optical Network (SONET) and ATM networks will continue

to support this popular network. In LANs, Ethernet links offer a scalable backbone, and a

high-speed campus data center backbone with inter-switch extensions. As a metro

backbone in MANs, gigabit Ethernet will interface in DWDM systems, allowing long

haul, high-speed broadband communications networks. Finally, Ethernet supports all


16/21

types of data traffic including data, voice, and video over IP. Figure illustrates a typical

Ethernet deployment scenario.

Figure: Switched, Routed Gigabit Ethernet Network

Gigabit Ethernet has emerged as a cost-effective alternative to ATM network

structures. ATM has a greater cost, and he standards and products used to transmit ATM

are still in flux, unlike the proven paradigm of Ethernet. In addition, system complexity is

reduced in gigabit Ethernet, and because it works with existing Ethernet formats, the

system does not require emulation software to act as a gateway between an Ethernet LAN

and an ATM network. Table.1 outlines how Ethernet and gigabit Ethernet offer the same

benefits of ATM.

Areas of application:

Tele communication:


17/21

Optical fibers are now the standard point-to-point cable link between telephone

sub stations. It is said that currently, the fastest fibers circuits used in trunk connections

between cities and countries carry information at up to 2.5 giga bytes per second, enough

to carry 40,000 telephone conversations. Experts predict larger bandwidths than this as

light frequencies suppression becomes available.

Local area networks (LANs):

Multimode fiber is commonly used as the backbone to carry signals between the

hubs of a LANs from where copper coaxial cable takes the data to the desktop. Fiber

links to the desktop, however, are also common.

Cable TV:

The domestic cable TV networks use optical fiber because of its very low power

consumption. The fastest fiber circuits carry information at up to 250 television channels.

CCTV:

Closed Circuit Television security systems use optical fiber because of its

inherent security, as well as the other advantages mentioned above.

Optical fiber sensors:

Many advances have been made in recent years in the use of optical fiber sensors.

Gas concentration, chemical concentration, pressure, temperature and rate of rotation can

all be sensed using optical fiber.

5.0 Merits


18/21

1. Immunity to electromagnetic interference and crosswalk.

2. No electrical ground loop or short circuit problems.

3. Small size and lightweight.

4. Large bandwidth for size and weight.

5. Safe in combustible areas (no arching).

6. Immunity to lightning and electrical discharges.

7. Longer cable runs between repeaters.

8. Flexibility and high strength.

9. Potential high temperature operation.

10. Resistant to nuclear radiation.

11. Secure against signal leakage and interference.

12. No electrical hazard when cut or damaged.

13. Compatible with future bandwidth requirements and future LAN standards.

(FDDI, ATM)

14. The dielectric nature of optical fiber can eliminate the dangers found in areas of

high lightning strike incident

15.Non-Conductivity: Another advantage of optical fibers is their dielectric nature.

Since optical fiber has no metallic components, it can be installed in areas with

electromagnetic interference (EMI), including Radio Frequency Interference (RFI).

Areas with high EMI include utility lines, power-carrying lines, and railroad tracks.

All-dielectric cables are also ideal for areas of high lightning-strike incidence.


19/21

16.Security: Unlike metallic-based systems, the dielectric nature of optical fiber

makes it impossible to remotely detect the signal being transmitted within the cable.

Only way to do so is by actually accessing the optical fiber itself. Accessing fiber

requires intervention that is easily detectable by security surveillance. These

circumstances make fiber extremely attractive to governmental bodies, banks, and

others with security concerns.

17.Designed for Future Applications Needs: Fiber optics is affordable today, as

electronics prices fall and optical cable pricing remains low. In many cases, fiber

solutions are less costly than copper.

6.0 Demerits

1. Relatively expensive cable cost and installation cost.

2. Requires specialist knowledge and test equipment.

3. No IEEE 802.5 standard published yet.

4. Relatively small installed base.

FIGURES:

(Figure 1.1a) (Figure 1.1b)


20/21

THIN OPTICAL FIBERS CONSTRUCTION

(Figure 1.3a)

TOTAL INTERNAL REFLECTION

(FIGURES 2.0a, 2.0b, 2.0c)

Types of optical fibers


21/21

CONCLUSION

The development of ultra-high capacity local- and wide-area computer networks

is also of interest to address the exponential growth of Internet traffic. The development

of high-speed multimedia networks puts increasing demand for higher bandwidth

channels and networks. Such demands may require transmission of information at an

ultra-high bit rate of terabits/sec over fiber optics. Thus Fiber Optics will play a pivotal

role in this race since the bandwidth needed for providing an all in-one service with

television, telephone, interactive multimedia, and Internet access is not available in much

of the wiring.

REFERENCES

1. Optical Transmission Medium, by Pradeep Atria, pp.16-21, Electronics

Makers June 2004 ed.

2. www.fiber-optics.com

3. www.engineeringlab.com/fiber optic6.htm

4. www.optics2001.com

5. www.fiber-optics.info

fibre optics communication

Documents