Extending the workload ofthe 3000 series calibrators

Laboratories usually have to calibrate a very wide variety of instruments.

Normal the volume of the odd instruments is small, and this is in part some of the problem. It produces a requirement to provide a cost efficient method to calibrate these instruments.

This is where the Transmille offers a real alternative. As a calibration laboratory ourselves we suffer the same problem, and we know to sub contract instruments can lose the whole contract.

So what can the Transmille Calibrate

Transmille offer a range of options to cover all the standard products just as the other calibrators: e.g. DMMs, clamp meter, power meter, oscilloscopes, frequency counters, thermometers, pressure etc etc, But what about the other instruments, in our lab we have to calibrate all sorts ….

Question you ask before you buy a calibrator.

How can I calibrate an RCL Meter ?RLC meters are not un- common, and almost ever laboratory will need to calibrate.

The 2000 series uses passive resistors and capacitors, and is the only calibrator on the market with an inductance option.

Its no problem with the Transmille calibrator….

Question to ask before you buy a calibrator.How can I calibrate an Tacho Meter ?Tacho meters are in common use in industry,and often appear in the calibrations workload.

With the adaptor for the Transmille, opto tachometers can be calibrated quickly and without any difficulty, transforming the situation form ‘how do I do this’ to ‘its done’

Its no problem with the Transmille calibrator….

Question to ask before you buy a calibrator.Question to ask before you buy a calibrator.

How can I calibrate a HV Probe?

High voltage probes are not un-common, and are not difficult to calibrate, but with all other calibrator the answer is we can’t.With a Transmille calibrator and the HV amp its easy.

Its no problem with the Transmille calibrator….

Question to ask before you buy a calibrator.Question to ask before you buy a calibrator.

How can I calibrate a Power Supply? This must be one of the most common instruments, yet only Transmille offer

an easy to use low cost solution.The EA2023 Not only measures the power supply output voltage up to 60volts, (using the measurement capability of the pod input) but also provides an accurate current load up to 4Amps. Output resistance can also be measured and there

is even a wizard in Procal to create procedures.

Its no problem with the Transmille calibrator….

Question to ask before you buy a calibrator.Question to ask before you buy a calibrator.

How can I calibrate an Electrometer/Pico amp meter?

Keithly and others manufacture a wide range of low current meters with scales down to only a few nano amps. These are often used in semiconductor manufacturing or for high value resistance measurement.

A calibrator only covers ranges down to a few micro amps so these are not suitable.

With the EA??? Transmille again provide a solution. Extending the range of the calibrator down to 2nA.

Its no problem with the Transmille calibrator….

Question to ask before you buy a calibrator.Question to ask before you buy a calibrator.How can I calibrate a 1Tohm resistor? You can buy an expensive electrometer or make the most of your investment

in a Transmille calibrator by using low cost Pico amp converter EA??? for the Transmille calibrator.

The ability to measure a high value resistance at a selected voltage is an important ability in any laboratory, but it is always difficult to justify the expense of an electrometer for the small number of calibrations performed with it. When you buy a calibrator you have already bought a precision voltage source, ( with a power supply, processor etc) and with the Transmille a high accuracy a/d converter, so all that is needed to make the calibrator into a full featured electrometer is the EA008 And software.

Its no problem with the Transmille calibrator….

Question to ask before you buy a calibrator.Question to ask before you buy a calibrator.

How can I calibrate a 2000A clamp meter or high current shunts?

High current calibration is easily covered by expensive Trans- conductance amplifiers… if you can justify the cost. Often the volume of such work is small so this can be difficult.

With Transmille EA012, which has been custom designed to work with the calibrator, there is a much lower cost solution.

Its no problem with the Transmille calibrator….

Simply with Transmille you can Simply with Transmille you can calibrate a wider range of calibrate a wider range of products for less money……products for less money……

Use Procal calibration software Use Procal calibration software and produce certificates in less and produce certificates in less time as well….. time as well…..

How can Transmille do all How can Transmille do all this ?this ?We are ourselves a commercial cal lab, the

development of our products has been drawn form the needs we face daily in our own laboratory.

To be competitive and successful (and Transmille have grown 10 fold in the last 8 years) we needed the best software and calibrators available. Finding the alternatives inefficient we applied our design experience to building something better.

Revolutionary Thinking or just Revolutionary Thinking or just Evolution ?Evolution ? The 2000 series design was to include the

‘pod’ connector which would allow the use of a range of external adaptors specifically designed to calibrate generic types of instruments.

Revolutionary Thinking or just Revolutionary Thinking or just Evolution ?Evolution ? As the adaptors would not need power

supplies, processors, displays etc they would be low cost.

Measurements are made using a high accuracy a/d internal to the calibrator. The adaptor would simple have to scale all inputs to 10V.

Revolutionary Thinking or just Revolutionary Thinking or just Evolution ?Evolution ? The external adaptors could be designed to

perform a specific task. Making them very easy to use.