odonta.org en.pdf · -04 pack of 4 abs acrylonitrile butadiene styrene al aluminum bl bone level...

PRoduct catalog2012

PRoduct catalog2012

NoteA list of abbreviations can be found on the reverse of this fold-out page. This list of abbreviations gives an overview of implants, platforms, materials and packaging units.

-04 Pack of 4ABS Acrylonitrile butadiene styreneAl AluminumBL Bone LevelLDPE Low-density polyethyleneMO 0 Medium Opacity 0MO 1 Medium Opacity 1NC Narrow CrossFit® = implant diameter 3.3 mm, BL implantsNN Narrow Neck = implant shoulder diameter 3.5 mm, SP implantsNNC Narrow Neck CrossFit® = implant shoulder diameter 3.5 mm,

SP implantsPA PolyamidePC PolycarbonatePEEK PolyetheretherketonePMMA PolymethylmethacrylatePOM PolyoxymethylenePPS Polyphenylene sulfidePS PolystyrenePSU PolysulfoneRC Regular CrossFit® = implant diameter 4.1 and 4.8 mm, BL implantsRN Regular Neck = implant shoulder diameter 4.8 mm,

S/SP/TE implantsS StandardSCS Screw Carrying SystemSLA® Sand-blasted, Large grit, Acid-etchedSLActive® Sand-blasted, Large grit, Acid-etched,

chemically active and hydrophilicSP Standard PlusTAN Titanium-aluminum-niobium alloyTAV Titanium-aluminum-vanadium alloyTE Tapered EffectTi TitaniumTiN Titanium nitrideTiZr Titanium-zirconium alloy (Roxolid®)TS Transversal screw retentionV2 Pack of 2V4 Pack of 4V20 Pack of 20WN Wide Neck = implant shoulder diameter 6.5 mm, S/SP/TE implantsZrO2 Zirconium dioxide

LIST OF ABBREVIATIONS

1

CONTENTS

GENERAL

Introduction 3The International Team for Implantology (ITI) 4The Straumann Guarantee 5Important Guidelines 6List of symbols 7Explanation of coding and types 8Explanation of labeling 9Additional information 10Contacts 14

GENERAL PAGE

Introduction 3The International Team for Implantology (ITI) 4The Straumann Guarantee 5Important Guidelines 6List of symbols 7Explanation of coding and types 8Explanation of labeling 9Additional information 10Contacts 14

REGENERATION

Straumann® Emdogain, Straumann® Emdogain PLUS and Straumann® PrefGel 20Straumann® BoneCeramic 21Straumann® Bone Block Fixation 1.5 mm 22

REGENERATION


SURGERY

Straumann® CARES® Guided Surgery 25Surgical planning aids 29Overview titanium implants 32Overview Roxolid® Implants 34Standard implants 35Standard Plus implants 41Tapered Effect implants 49Bone Level implants 55TempImplants 63Surgical instruments 65Auxiliary instruments 94Surgical cassette 96Osteotomes 97Explantation 99Osstell™ mentor auxiliary components 102

SURGERY


PROSTHETICS

Cassettes, inserts and storage system 104Prosthetic instruments 106Prosthetics for Straumann® Standard, Standard Plus and Tapered Effect Implants 109● Prosthetic planning aids 110● Straumann® CARES® Implant-borne elements 113● Crowns and bridges 119● Hybrid dentures 149Prosthetics for Straumann® Bone Level implants 171● Prosthetic planning aids 172● Straumann® CARES® Implant-borne elements 178● Crowns and bridges 182● Hybrid dentures 209Straumann® Classic 231

PROSTHETICS

Cassettes, inserts and storage system 104Prosthetic instruments 106Prosthetics for Straumann® Standard, Standard Plus and Tapered Effect Implants 109● Prosthetic planning aids 110● Straumann® CARES® Implant-borne elements 113● Crowns and bridges 119● Hybrid dentures 149Prosthetics for Straumann® Bone Level implants 171● Prosthetic planning aids 172● Straumann® CARES® Implant-borne elements 178● Crowns and bridges 182● Hybrid dentures 209Straumann® Classic 231

SERVICE

Service materials 244

2

SERVICE PAGE


INDEX

Numerical index 248Alphabetical index 265

INDEX


At Straumann we are committed to providing high-quality and innovative solutions for dental professionals, as simply and efficiently as possible. This principle extends to our Product Catalog, which has been updated to help you more easily locate the most appropriate products for your needs.

You will find the contents of this catalog listed by procedure – allowing you to select the most suitable products according to the nature of the case – as well as indexed by article number and name.

Straumann® products receive the support of our scientific partners, the International Team for Implantology. We focus on the primary areas of implant and restorative dentistry and oral tissue regeneration and offer a comprehensive range of solutions in each of these areas:

Regeneration – materials and components devised to help restore naturally functioning teeth.

Surgery – implants, instruments and aids developed for those indications where a surgical intervention is required.

Prosthetics – abutments, copings and other prosthetic components designed for completion of a high-quality and functional procedure.

Although flexibility in treatment options is important to us, we feel that true Straumann quality can only be guaranteed when you choose original Straumann® products at every stage of the procedure.

We hope you find this catalog both interesting and informative. Please do not hesitate to contact your local Straumann representative for further information or visit our e-shop for 24/7 access to the full product range.

You can access the e-shop portal most relevant to your needs via your local Straumann website (i.e. www.straumann.ch for customers in Switzerland, www.straumann.de for Germany, etc.). Then simply click on the ‘e-shop’ tab within the menu at the top of the screen to be linked through to the shop.

GEN

ERAL

INTRODUCTION

3

The International Team for Implantology (ITI) unites professionals around the world from every field of implant dentistry. As an independent academic association, it actively promotes networking and exchange among its members and offers a wide array of membership benefits. In more than 30 years, the ITI has built a reputation for scientific rigor combined with concern for the welfare of patients. The organization focuses on the development of well-documented treatment guidelines backed by extensive clinical testing and the compilation of long-term results.

Straumann and the ITI enjoy a unique partnership. We are united by a shared mission: to constantly improve treatment methods and results in implant dentistry and related tissue regeneration for the benefit of patients.

Learn more about the ITI and register as a member at www.iti.org

GEN

ERAL THE INTERNATIONAL TEAM FOR IMPLANTOLOGY (ITI)

4

The new Straumann Guarantee applies if Straumann® products are used in combination with other original Straumann® products. Provided that the conditions of the Straumann Guarantee are fulfilled, the following guarantee periods are covered:

5-year guarantee period: for ceramic restorationsReplacement with an equivalent ceramic abutment (attached to a Straumann® Implant) or with an equivalent ceramic crown, coping or bridge restoration (for tooth and implant-supported restorations).

10-year guarantee period: for metal restorationsReplacement with an equivalent metal abutment (attached to a Straumann® Implant) or with an equivalent metal restoration (for tooth and implant- supported restoration).

Lifetime guarantee period: for implantsReplacement with an equivalent implant and an equivalent abutment, if necessary.

NoteFor applicable terms and conditions of the Straumann Guarantee (including theGuarantee territory) please refer to the Straumann Guarantee brochure (152.360/en).

GEN

ERAL

THE STRAUMANN GUARANTEE

5

Please notePractitioners must have appropriate knowledge and instruction in the handling of the Straumann® dental implants, Straumann CADCAM products, Straumann regenerative products or other Straumann products (“Straumann Products”) for using the Straumann Products safely and properly in accordance with the instructions for use.

The Straumann Product must be used in accordance with the instructions for use provided by the manufacturer. It is the practitioner’s responsibility to use the device in accordance with these instructions for use and to determine, if the device fits to the individual patient situation.

The Straumann Products are part of an overall concept and must be used only in conjunction with the corresponding original components and instruments distributed by Institut Straumann AG, its ultimate parent company and all affiliates or subsidiaries of such parent company (“Straumann”) or third party distributors. Use of products made by third parties, which are not distributed by Straumann, will void any warranty or other obligation, express or implied, of Straumann.

AvailabilitySome of the Straumann Products listed in this document may not be available in all countries.

CautionIn addition to the caution notes in this document, our products must be secured against aspiration when used intraorally. ValidityUpon publication of this document, all previous versions are superseded.

Documentation For detailed instructions on the Straumann Products contact your Straumann representative.

Copyright and trademarksStraumann® documents may not be reprinted or published, in whole or in part, without the written authorization of Straumann.

Straumann® and/or other trademarks and logos from Straumann® mentioned herein are the trademarks or registered trademarks of Straumann Holding AG and/or its affiliates.

GEN

ERAL IMPORTANT GUIDELINES

6

…min.

…max.

XXXX

…max.

…min.

STERILENON

Batch code Non-sterile

Catalog number Caution, consult accompanying documents

Sterile Use by

Sterilized using aseptic processing techniques

Keep away from sunlight

Sterilized using irradiation Keep away from sunlight

Lower limit of temperature Straumann Products with the CE mark fulfill the requirements of the Medical Devices Directive 93/42 EEC

Upper limit of temperaturexxxx identify the notified body of manufacturer

Temperature limitation Consult instructions for use

Caution: Federal law restricts this device to sale by or on the order of a dental professional

Manufacturer

Do not re-use Date of manufacture

Non-sterile

GEN

ERAL

LIST OF SYMBOLS

7

Color coding

yellow Endosteal implant diameter 3.3 mm

red Endosteal implant diameter 4.1 mm

green Endosteal implant diameter 4.8 mm

Implant types

S Standard Implant

SP Standard Plus Implant

TE Tapered Effect Implant

BL Bone Level Implant

Connection types

NNC: Narrow Neck CrossFit® Ø 3.5 mm

Ø 3.5 mm

NN: Narrow Neck Ø 3.5 mm

Ø 3.5 mm

RN: Regular Neck Ø 4.8 mm

Ø 4.8 mm

WN: Wide Neck Ø 6.5 mm

Ø 6.5 mm

NC: Narrow CrossFit® Ø 3.3 mm

Ø 3.3 mm

RC: Regular CrossFit® Ø 4.1 and Ø 4.8 mm

Ø 4.1 mm Ø 4.8 mm

GEN

ERAL EXPLANATION OF CODING AND TYPES

8

SPØ 3.3 NN

8

SPØ 3.3 NNC

SLActive8

SPØ 4.1 RNSLActive

10

TEØ 4.8 WNSLActive

12

BLØ 4.1 RCSLActive

12

SPØ 3.3 NN

8

SPØ 3.3 NNC

SLActive8

SPØ 4.1 RNSLActive

10

TEØ 4.8 WNSLActive

12

BLØ 4.1 RCSLActive

12

SPØ 3.3 NN

8

SPØ 3.3 NNC

SLActive8

SPØ 4.1 RNSLActive

10

TEØ 4.8 WNSLActive

12

BLØ 4.1 RCSLActive

12

SPØ 3.3 NN

8

SPØ 3.3 NNC

SLActive8

SPØ 4.1 RNSLActive

10

TEØ 4.8 WNSLActive

12

BLØ 4.1 RCSLActive

12

SPØ 3.3 NN

8

SPØ 3.3 NNC

SLActive8

SPØ 4.1 RNSLActive

10

TEØ 4.8 WNSLActive

12

BLØ 4.1 RCSLActive

12

Connection type

Implant type

Endosteal diameter

128 Barcode

Use by

Do not re-use

Straumann Products with the CE mark fulfill the requirements of the Medical Devices Directive 93/42/EEC

Caution, consult accompanying documents

Batch code

Catalog number

Sterilized using irradiation

Manufacturer

The Green Dot

Surface type

Caution: Federal law restricts this device to sale by or on the order

of a dental professional

Length of the SLA®/SLActive® surface

ExAMPLES

Straumann® Standard Plus ImplantEndosteal diameter 3.3 mmNarrow Neck8 mm SLA®

Straumann® Standard Plus Implant Endosteal diameter 3.3 mmNarrow Neck CrossFit®

8 mm SLActive®

Straumann® Standard Plus ImplantEndosteal diameter 4.1 mmRegular Neck10 mm SLActive®

Straumann® Bone Level ImplantEndosteal diameter 4.1 mmRegular CrossFit®

12 mm SLActive®

Straumann® Tapered Effect ImplantEndosteal diameter 4.8 mmWide Neck12 mm SLActive®

GEN

ERAL

EXPLANATION OF LABELINGEXAMPLE OF A LABEL ON IMPLANT PACKAGING

9

The properties of unalloyed grade 4 titanium for implants and abutments

a) Chemical composition

O0.40 % max.

Fe0.50 % max.

C0.10 % max.

N0.05 % max.

H0.012 % max.

TiBalance

b) Mechanical properties

Strength Elongation Modulus of elasticity

Forged/annealed 550 MPa min. 15 % min. 110 GPa

Cold-worked 680 MPa min. 10 % min. 110 GPa

Ti-N = titanium nitride-coating Process: Layer thickness: Color:

PVD (physical vapor deposition) 3–12 μm golden yellow

c) Technical information

Grade 4 titanium conforms to the ISO 5832-2 standard

The properties of the alloy Titanium Aluminium-6 Niobium-7 (TAN) for Straumann® abutments

a) Chemical Composition

Al5.5– 6.5 %

Nb6.5– 7.5 %

Ta0.50 % max.

Fe0.25 % max.

O0.20 % max.

C0.08 % max.

N0.05 % max.

H0.009 % max.

TiBalance

b) Mechanical properties

Strength Elongation Modulus of elasticity

Annealed 900 MPa min. 10 % min. 110 GPa

c) Technical information

The alloy Titanium Aluminium-6 Niobium-7 (TAN) conforms to the ISO 5832-11 standard

GEN

ERAL ADDITIONAL INFORMATION

MATERIAL INFORMATION

10

Alloys Ceramicor® Elitor®

Color white yellowish

Composition Au Pt Pd Ag Cu Ir Others

%%%%%%

+ = <1 %

60.019.020.0

1.0

68.62.54.0

11.810.6

+Zn 2.5

Melting range °C°F

1400–1490 2552–2714

880–9401616–1724

Coefficient of thermal expansion

CTE °C

CTE °F

25–500 °C = 11.9 μm/m x °C25–600 °C = 12.2 μm/m x °C

77–932 °F = 11.9 μm/m x °F77–1112 °F = 12.2 μm/m x °F

Hardness in as-delivered condition

HV5 220 260

Hardness after casting-on or soldering

HV5 205self-hardening

>260self-hardening

Hardened HV5 205 275

0.2 % Proof stress (Rp 0.2 %) as-delivered condition

N/mm2 780 780

0.2 % Proof stress (Rp 0.2 %) after casting-on or soldering

N/mm2 635 655

Possibilities for metallic bonding

casting-on or soldering soldering

Technical information Applications

Non-oxidizing alloy for casting-on with precious metal alloys or for soldering with precious metal or

non-precious metal alloys

Alloy for construction elements attachments

GEN

ERAL

ADDITIONAL INFORMATIONMATERIAL INFORMATION

11

Alloys Esteticor® Cosmor H

Color pale yellow

Composition Au + Pt-MetalsAu PtPd In Ir

%%%%%%

96.578.510.0

7.83.50.2

Melting range °C°F

1120–1280 2048–2336

Coefficient of thermal expansion

CTE °C

°F

25–500 °C = 13.8 μm/m x °C25–600 °C = 14.0 μm/m x °C

77–932 °F = 13.8 μm/m x °F77–1112 °F = 14.0 μm/m x °F

ISO 9693 pos. 6.3.3.3 positive

Hardness after firing HV5 215

Tensile strength (Rm) after firing

N/mm2 705

0.2 % Proof stress (Rp 0.2 %) after firing

N/mm2 565

Elongation at break (A5) after firing

% 12.5

Density g/cm2 18.2

Technical informationApplications

Low oxidationAlloy corresponds to ISO 9693 standard

GEN

ERAL ADDITIONAL INFORMATION

MATERIAL INFORMATION

12

Directives 93/42/EECAll production stages carried out by Institut Straumann AG are subject to the standards laid down in the EN ISO 9001 quality assurance system. This European standard establishes in detail the criteria which, in order to be recognized, a company must fulfill regarding comprehensive quality assurance during its manufacturing processes.

Medical products have to meet extremely strict requirements, and with good reason. These requirements are defined in the European standard ISO 13485, which we also fulfill. This ensures that the quality of our products and servicesmeets our customers‘ expectations and can be reproduced and traced at any time.

Straumann products with the CE mark fulfill the requirements of the Medical Device Directive 93/42 EEC.

Institut Straumann AG fulfills the stringent requirements of the European Directive 93/42/EEC for medical devices as well as the EN ISO 9001 and ISO 13485 standards.

GEN

ERAL

ADDITIONAL INFORMATIONQUALITY AT THE CUSTOMER‘S SERVICE

13

AlgeriaTaourirt Dentaire SARL38, parc Ben Omar KoubaDZ-AlgerPhone: +213 2128 0132Fax: +213 2129 9910E-mail: [email protected]

AndorraStraumann S.A.Edificio Arroyo AAvda. Bruselas, 38ES-28108 Alcobendas - MadridPhone: +34 91 344 7700 Fax: +34 91 344 9517E-mail: [email protected]

AngolaASM Consultants (Pty) Ltd.PO Box 1453Parklands 2121ZA-JohannesburgPhone: +27 11 447 1511Fax: +27 11 880 8694E-mail: [email protected]

ArgentinaSyncrotech SRLJerónimo Salguero 1575 3°pisoAR-1177 Buenos AiresPhone: +54 11 4511 9520Fax: +54 11 4511 9524E-mail: [email protected]

AustraliaStraumann Australia P/L7 Gateway CrtAU-Port Melbourne 3207, VictoriaPhone: +61 3 9646 7060Fax: +61 3 9646 7232Phone: 1800 660 330 (toll free for Australia)Phone: 0800 408 370 (toll free for New Zealand)E-mail: [email protected]

AustriaStraumann GmbHFlorido TowerFloridsdorfer Hauptstrasse 1AT-1210 ViennaPhone: +43 1 294 0660Fax: +43 1 294 0666E-mail: [email protected]

BahrainGulf PharmacyVilla 390, Rd. 3009, New Zinj 330P.O. Box 2576BH-ManamaPhone: +973 1723 9399Fax: +973 1723 2230E-mail: [email protected]

BelgiumStraumann NV/ SABelgicastraat 3/ Building 503BE-1930 ZaventemPhone: +32 2 790 1000Fax: +32 2 790 1020E-mail: [email protected]

BotswanaASM Consultants (Pty) Ltd.PO Box 1453Parklands 2121ZA-JohannesburgPhone: +27 11 447 1511Fax: +27 11 880 8694E-mail: [email protected]

BrazilStraumann Brasil LtdaRua Funchal 263 – 12° andarVila OlímpiaBR-04551-060 São Paulo (SP)Phone: +55 11 3058 6888Fax: +55 11 3058 6899E-mail: [email protected]

BruneiTitleray Dental Implantsc/o Ricerfarma Marketing (M) Sdn BhdA-5-28, Penthouse SuiteIOI Boulevard, Jalan Kenari 5Bandar Puchong JayaMY-47170 Puchong, Selangor DEPhone: +60 3 8075 4644Fax: +60 3 8075 0995E-mail: [email protected]

BulgariaUltradental Ltd.Kniaz Boris I Str., No. 10, ground floorBG-1463 SofiaPhone: +359 2 953 3557Fax: +359 2 953 3559E-mail: [email protected]

CambodiaTitleray Dental Implantsc/o Ricerfarma Marketing (M) Sdn BhdA-5-28, Penthouse SuiteIOI Boulevard, Jalan Kenari 5Bandar Puchong JayaMY-47170 Puchong, Selangor DEPhone: +60 3 8075 4644Fax: +60 3 8075 0995E-mail: [email protected]

CanadaStraumann Canada Ltd.3115 Harvester Road, Suite 100Burlington, Ontario L7N 3N8Phone: +1 905 319 2900 Fax: +1 905 319 2911E-mail: [email protected]

ChileTecnoImport/ExportMatias Cousiño 64, Of. 707CL-Santiago de ChilePhone: +56 2 695 2677Fax: +56 2 696 5714E-mail: [email protected]

ChinaStraumann (Beijing) Medical Device Consulting Co. Ltd. 11th floor, Tower B, Jiaming Centre 27#, Dongsanhuan Beilu Chaoyang District CN-Beijing 100020Phone: +86 10 5775 6555 Fax: +86 10 5775 6556 E-mail: [email protected]

ChinaBeijing Focus Medical Instrument Co. Ltd.6th floor, Fairyland Plaza83#, Fuxing Road, Haidian DistrictCN-Beijing 100856Phone: +86 10 8861 2668Fax: +86 10 8820 3991E-mail: [email protected]

ColombiaMagnetron Zona Franca S.AZona Franca del Eje CafeteroBodega 50CO-La Tebaida, QuindioPhone: +57 6 747 9857Fax: +57 6 315 7110E-mail: [email protected] [email protected]

GEN

ERAL CONTACTS

14

CroatiaSanitaria Zagreb d.o.o.Korculanska 4-6HR-1000 ZagrebPhone: +385 1618 1178Fax: +385 1618 3059E-mail: [email protected]

Czech RepublicStraumann s.r.o.Na Žertvách 2196CZ-180 00 Prague 8Phone: +420 2 8409 4650Fax: +420 2 8409 4659E-mail: [email protected]

DenmarkStraumann Danmark ApSNygårds Plads 21, 1.DK-2605 Brøndby Phone: +45 4616 0666 Fax: +45 4361 2581 E-mail: [email protected]

DenmarkFor Straumann® EmdogainLight HouseStaeremossen 56DK-3250 Gilleleje Phone: +45 48 28 56 46Fax: +45 48 28 60 16E-mail: [email protected]

EgyptProdent s.a.l.Corniche al Nahr, Victoria Tower Bldg.P.O. Box 165 8841100 2080 AshrafiehLB-BeirutPhone: +961 1 425 042Fax: +961 1 424 642E-mail: [email protected]

EstoniaStraumann OyFredrikinkatu 48 A 7 krsFI-00100 HelsinkiPhone: +358 9694 2877Fax: +358 9694 0695E-mail: [email protected]

FinlandStraumann OyFredrikinkatu 48 A 7 krsFI-00100 HelsinkiPhone: +358 9694 2877Fax: +358 9694 0695E-mail: [email protected]

FranceStraumann S.à.r.l.3, rue de Galmy-ChessyFR-77701 Marne-la-Vallée, Cedex 4Phone: +33 1 6417 3000Fax: +33 1 6417 3010E-mail: [email protected]

GermanyStraumann GmbHJechtinger Strasse 9DE-79111 FreiburgPhone: +49 761 4501 0Fax: +49 761 4501 149E-mail: [email protected]

GreeceDenco Dental SA15 Mesogion AvenueGR-11526 AthensPhone: +30 210 777 0670Fax: +30 210 748 6002E-mail: [email protected]

Hong KongAdvance Dental ConsultingRoom 1303-05, Wing Kwok Centre182 Woo Sung StreetJordan, KowloonHK-Hong KongPhone: +852 2384 7666Fax: +852 2388 0960E-mail: [email protected]

HungaryStraumann GmbH Magyarországi FióktelepeM3 Business CenterHungária körút 179-187HU-1146 BudapestPhone: +36 1 787 1095Fax: +36 1 787 1096E-mail: [email protected]

IcelandE. Bridde ehfHoltasmári (7th Floor)IS-201 KópavogurPhone: +354 577 1215Fax: +354 577 1216E-mail: [email protected]

IndonesiaFondacoAPL Tower, Podomoro City27th Floor, Suite 2Jl. Letjen S. Parman Kav. 28Grogol PetamburanID-Jakarta Barat 11470Phone: +62 21 2903 4388Fax: +62 21 2903 4391E-mail: [email protected]

IranMehrarabon Co. - NorouziNo. 1, 1st Floor, Block AKaveh Bldg., Azadi Ave.IR-1313654913 TeheranPhone: +98 21 6643 5999Fax: +98 21 6642 2908E-mail: [email protected]

IraqProdent s.a.l.Corniche al Nahr, Victoria Tower Bldg.P.O. Box 165 8841100 2080 AshrafiehLB-BeirutPhone: +961 1 425 042Fax: +961 1 424 642E-mail: [email protected]

IrelandStraumann Ltd.3 Pegasus PlaceGatwick RoadGB-Crawley RH10 9AY, West SussexPhone: +44 1293 65 1230Fax: +44 1293 65 1239E-mail: [email protected]

IsraelDentorient Fuss28, Hagdud Haivri StreetP.O. Box 2232IL-Tel Aviv 61021Phone: +972 2 3639 3640Fax: +972 2 3639 3645E-mail: [email protected]

GEN

ERAL

CONTACTS

15

IsraelFor regenerative productsH.A. Systems Ltd.Tuval StreetIL-52522 Ramat-GanPhone: +972 3 6138777Fax: +972 3 6138778E-mail: [email protected]

ItalyStraumann Italia srlViale Bodio 37IT-20158 MilanoPhone: +39 02 3932 831Fax: +39 02 3932 8365E-mail: [email protected]

JapanFor Straumann® Dental Implant System and CARES® Digital SolutionsStraumann Japan K.K.Sapia Tower 16F1-7-12 Marunouchi, Chiyoda-kuJP-Tokyo 100-0005Phone: +81 3 5218 2600Fax: +81 3 5218 2601E-mail: [email protected]

JordanArab Medical & Scientific Alliance A.M.S.A.P.O. Box 2509, 11953 Tela’ Al-AliJO-AmmanPhone: +962 6 552 8009Fax: +962 6 553 2358E-mail: [email protected]

KuwaitAlphaMedical Co.Floor No. 13, Bldg. No. 15Arabian Gulf Road, St. No. 64, Block No. 6Bneid Al-Qar City, PO Box 6267KW-22006 SalmiyahPhone: +965 2 247 8612Fax: +965 2 247 8613E-mail: [email protected]

LatviaJSC “MED GRUPE”Polocko str. 21/Zvirgzdyno g. 1LT-01205 VilniusPhone: +370 5 276 1377Fax: +370 5 275 6850E-mail: [email protected]

LebanonProdent s.a.l.Corniche al Nahr, Victoria Tower Bldg.P.O. Box 165 8841100 2080 AshrafiehLB-BeirutPhone: +961 1 425 042Fax: +961 1 424 642E-mail: [email protected]

LiechtensteinInstitut Straumann AGPeter Merian-Weg 12CH-4002 BaselPhone: +41 61 965 1111Fax: +41 61 965 1101E-mail: [email protected]

LithuaniaJSC “MED GRUPE”Polocko str. 21 / Zvirgzdyno g. 1LT-01205 VilniusPhone: +370 5 276 1377Fax: +370 5 275 6850E-mail: [email protected]

LuxembourgStraumann NV/ SABelgicastraat 3 / Building 503BE-1930 ZaventemPhone: +32 2 790 1000Fax: +32 2 790 1020E-mail: [email protected]

MalaysiaTitleray Dental Implantsc/o Ricerfarma Marketing (M) Sdn BhdA-5-28, Penthouse SuiteIOI Boulevard, Jalan Kenari 5Bandar Puchong JayaMY-47170 Puchong, Selangor DEPhone: +60 3 8075 4644Fax: +60 3 8075 0995E-mail: [email protected]

MaltaBart Enterprises Ltd.42A, Main StreetMT-Balzan BZN 06Phone: +356 2144 7340Fax: +356 2144 7341E-mail: [email protected]

MexicoStraumann México SA de CVRubén Dario #281 int. 1702 Piso 17Col. Bosque de ChapultepecMX-11580 México, D.F.Phone: +52 55 5282 6262Fax: +52 55 5282 6289E-mail: [email protected]

MonacoStraumann S.à.r.l.3, rue de Galmy-ChessyFR-77701 Marne-la-Vallée, Cedex 4Phone: +33 1 6417 3000Fax: +33 1 6417 3010E-mail: [email protected]

MontenegroImplantodent D.O.O.Oblakovska 2gCS-11000 BeogradPhone: +381 11 344 9143Fax: +381 11 369 2008E-mail: [email protected]

MoroccoSociété Academy3, rue Tabit Bnou Korra, (Avenue Driss 1er)Quartier des HôpitauxMA-20360 CasablancaPhone: +212 5 2286 2671Fax: +212 5 2286 2672E-mail: [email protected]

NamibiaASM Consultants (Pty) Ltd.PO Box 1453Parklands 2121ZA-JohannesburgPhone: +27 11 447 1511Fax: +27 11 880 8694E-mail: [email protected]

NetherlandsStraumann BVEinsteinweg 15NL-3404 LE IJsselsteinPhone: +31 30 604 6611Fax: +31 30 604 6728E-mail: [email protected]

GEN

ERAL CONTACTS

16

New ZealandStraumann Australia P/L7 Gateway CrtAU-Port Melbourne 3207, VictoriaPhone: +61 3 9646 7060Fax: +61 3 9646 7232Phone: 1800 660 330 (toll free for Australia)Phone: 0800 408 370 (toll free for New Zealand)E-mail: [email protected]

NorwayStraumann ASNedre Vollgate 3P.O. Box 1751 VikaNO-0122 OsloPhone: +47 2335 4488Fax: +47 2335 4480E-mail: [email protected]

OmanIbn Sina Medical Supply LLCP.O. Box 481OM-116 Mina Al-FahalPhone: +968 2450 1836Fax: +968 2450 2840E-mail: [email protected]

PakistanAhmad Enterprises7-B New Muslim TownPK-Lahore, PunjabPhone: +92 42 586 6975Fax: +92 42 586 0945E-mail: [email protected]

ParaguaySyncrotech SRLJerónimo Salguero 1575 3°pisoAR-1177 Buenos AiresPhone: +54 11 4511 9520Fax: +54 11 4511 9524E-mail: [email protected]

PhilippinesEuro Asia Specialty Dental Corporation39th Floor, Summit One Office Tower530 Shaw Blvd.PH-Mandaluyong City 1550Phone: +63 2 533 1300Fax: +63 2 533 1300 + 3E-mail: [email protected]

PolandSchlamberger Sp. z o.o.al. Jerozolimskie 81, ORCO Tower, 12th floorPL-02-001 WarsawPhone: +48 22 695 0080Fax: +48 22 695 0081E-mail: [email protected]

PortugalStraumann S.A.Lagoas Park, Edificio 11, Piso 3PT-2740-244 Porto SalvoPhone: +351 21 422 9170Fax: +351 21 421 2144E-mail: [email protected]

QatarAli Bin AliAbdullah Bin Thani StreetP.O. Box 75QA-DohaPhone: +974 4 446 9888Fax: +974 4 436 1000E-mail: [email protected]

RomaniaImplant Division s.r.l.Str. Dr. Anibal Teohari Nr. 8Demisol Camera 1, Sector 5RO-050674 BucharestPhone: +40 21 4106 801E-mail: ruxandra.popescu@ implantdivision.com

RussiaOOO ”MEDTECH Implant”Pr. Wernadskogo, 103, Bldg. 1, Off. 29RU-119 526 MoscowPhone: +7 495 434 3379Fax: +7 495 786 6559E-mail: [email protected]

SambiaASM Consultants (Pty) Ltd.PO Box 1453Parklands 2121ZA-JohannesburgPhone: +27 11 447 1511Fax: +27 11 880 8694E-mail: [email protected]

Saudi ArabiaThimar Al Jazirah56 Prince Fawaz Bin Abdul Aziz St.Malaz Dist.SA-11421 RiyadhPhone: +966 1 445 4545Fax: +966 1 493 4568E-mail: [email protected]

SerbiaImplantodent D.O.O.Oblakovska 2gCS-11000 BeogradPhone: +381 11 344 9143Fax: +381 11 369 2008E-mail: [email protected]

SingaporeImplant FocusNo. 6 Ubi Road 1#03-01Wintech CentreSG-Singapore 408726Phone: +65 6741 5411Fax: +65 6742 3593E-mail: [email protected]

SloveniaDentalia d.o.o.Celovska 197SI-1000 LjublianaPhone: +386 1 583 7730Fax: +386 1 510 3215E-mail: [email protected]

South AfricaASM Consultants (Pty) Ltd.PO Box 1453Parklands 2121ZA-JohannesburgPhone: +27 11 447 1511Fax: +27 11 880 8694E-mail: [email protected]

South KoreaStraumann Dental Korea Inc.1005 Korea Trade TowerSamseong 1-dongGangnam-guKR-Seoul 135-729Phone: +82 2 2149 3800Fax: +82 2 2149 3810E-mail: [email protected]

GEN

ERAL

CONTACTS

17

SpainStraumann S.A.Edificio Arroyo AAvda. Bruselas, 38ES-28108 Alcobendas - MadridPhone: +34 91 344 7700 Fax: +34 91 344 9517E-mail: [email protected]

SwedenStraumann ABFabriksgatan 13SE-41250 GothenburgPhone: +46 31 708 7500Fax: +46 31 708 7529E-mail: [email protected]

SwitzerlandInstitut Straumann AGPeter Merian-Weg 12CH-4002 BaselPhone: +41 61 965 1111Fax: +41 61 965 1101E-mail: [email protected]

SyriaProdent s.a.l.Corniche al Nahr, Victoria Tower Bldg.P.O. Box 165 8841100 2080 AshrafiehLB-BeirutPhone: +961 1 425 042Fax: +961 1 424 642E-mail: [email protected]

TaiwanKingcraft Scientific Inc.13F-1, No. 356, Sec. 5Nanking E. Rd.TW-10569 TaipeiPhone: +886 2 2742 2772Fax: +886 2 2748 6267E-mail: [email protected]

ThailandDKSH (Thailand) Limited280 New RoadTH-Bangkok 10100Phone: +66 2220 9000Fax: +66 2225 8992E-mail: [email protected]

TunisiaRecta MedicaRésidence El Yamama, Blc B, 2ème étageApp. no. 23, El Manar ITN-2092 TunisPhone: +216 71 871 960Fax: +216 71 885 214E-mail: [email protected]

TurkeyBati DentalAksu Sokak No. 9/18-19SihhiyeTR-06410 AnkaraPhone: +90 312 434 2000Fax: +90 312 434 2042E-mail: [email protected]

UkraineINSPE42, Br. Mikhnovskykh Str.UA-79018 LvivPhone: +38 32 240 3705Fax: +38 32 294 8399E-mail: [email protected]

United Arab EmiratesAl-Hayat Pharmaceuticals U.A.E.Al Whada StreetP.O. Box 4483AE-SharjahPhone: +971 6 559 2481Fax: +971 6 559 3573E-mail: [email protected]

United KingdomStraumann Ltd.3 Pegasus PlaceGatwick RoadGB-Crawley RH10 9AY, West SussexPhone: +44 1293 65 1230Fax: +44 1293 65 1239E-mail: [email protected]

UruguaySyncrotech S.A.Avenida Brasil 2483Oficina 702Esq. ObligadoUY-11300 MontevideoPhone: +598 2 708 3236E-mail: [email protected]

USAStraumann USA LLC60 Minuteman RoadUS-Andover, MA 01810Phone: +1 978 747 2500Fax: +1 978 747 2490E-mail: [email protected]

VietnamDKSH Vietnam Co. Ltd.2nd Floor, Etown 2 Building364 Cong Hoa StreetTan Binh DistrictVN-Ho Chi Minh CityPhone: +84 8 3812 5848Fax: +84 8 3812 5778E-Mail: [email protected]

ZimbabweASM Consultants (Pty) Ltd.PO Box 1453Parklands 2121ZA-JohannesburgPhone: +27 11 447 1511Fax: +27 11 880 8694E-mail: [email protected]

International HeadquartersInstitut Straumann AG Peter Merian-Weg 12CH-4002 Basel, SwitzerlandPhone: +41 (0)61 965 11 11Fax: +41 (0)61 965 11 01

GEN

ERAL CONTACTS

18

REG

ENER

ATIO

N

REGENERATION

REG

ENER

ATIO

N

19


REG

ENER

ATI

ON

20

STRAUMANN® EMDOGAIN, STRAUMANN® EMDOGAIN PLUSAND STRAUMANN® PrefGel

Art. No. Article

075.101 Straumann® Emdogain 0.3 mlcontains:1 x Straumann® Emdogain 0.3 ml

075.102 Straumann® Emdogain 0.7 mlcontains:1 x Straumann® Emdogain 0.7 ml

075.114 Straumann® Emdogain 0.3 mlmultipack incl. Straumann® PrefGelcontains:3 x Straumann® Emdogain 0.3 ml,3 x Straumann® PrefGel 0.6 ml ready-to-use syringe

075.116 Straumann® Emdogain 0.7 mlmultipack incl. Straumann® PrefGelcontains:3 x Straumann® Emdogain 0.7 ml,3 x Straumann® PrefGel 0.6 ml ready-to-use syringe

075.117 Straumann® Emdogain PLUSincl. Straumann® PrefGel and Straumann® BoneCeramiccontains:1 x Straumann® Emdogain 0.7 ml,1 x Straumann® BoneCeramic 400–700, 0.25 g,1 x Straumann® PrefGel 0.6 ml ready-to-use syringe

075.203 Straumann® PrefGel 0.6 mlcontains:5 x Straumann® PrefGel 0.6 ml ready-to-use syringe

Ordering and delivery of Straumann® Emdogain and Straumann® Emdogain PLUSThe certified quality assurance system for this medical product, which applies to both production and logistics,stipulates that it must be kept in refrigerated storage (at 2 °C–8 °C). Interruption of refrigeration for up to 72 hours,e.g. during transportation, is permissible.

For this reason, Straumann has special delivery arrangements. Please contact your local distributor for details.

Ordering and delivery of Straumann® PrefGelStraumann® PrefGel must be kept in refrigerated storage (at 2 °C–8 °C). Interruption of refrigeration, e.g. duringtransportation, is permissible. The package should, however, be placed in the refrigerator as soon as possible.

The normal terms of delivery apply for Straumann® PrefGel.

The right of return does not apply to Straumann® Emdogain, Straumann® Emdogain PLUS or Straumann® PrefGel.

REG

ENER

ATIO

N

21

STRAUMANN® BoneCeramic

Art. No. Article Dimensions

070.203 Straumann® BoneCeramic400–700

Granule size: 400–700 µm,Unit size: 0.25 g,Volume: approx. 0.3 ml


Granule size: 500–1000 µm,Unit size: 0.5 g,Volume: approx. 0.95 ml


Granule size: 500–1000 µm,Unit size: 1 g,Volume: approx. 1.9 ml

REG

ENER

ATI

ON

22

STRAUMANN® BONE BLOCK FIXATION 1.5 mm

Art. No. Article Dimensions Material

Basic set

041.032 Straumann® Bone BlockFixationcassette for drills, mini-screws and screwdriver forbone block fixation

Length 130 mm,Width 118 mm,Height 25 mm

Thermoplastic

044.125 Glide hole drill Length 37 mm,Stop 20 mm,Ø 1.5 mm

Stainlesssteel

044.126 Residual ridge drill Length 37 mm,Stop 16 mm,Ø 1.25 mm

Stainlesssteel

042.700V5 Crosshead mini-screw Length 8 mm,Ø 1.5 mm

Ti


Ti


Ti


Ti

040.360 Screwdrivercomplete, with screwdriverblade and screw-holdingdevice for implant screws,crosshead Ø 1.5 mm

Length 160 mm Al/Stainlesssteel

Spare parts

046.256 Screwdriver bladefor implant screws,crosspoint Ø 1.5 mm

Length 69 mm Stainlesssteel

046.257 Screw-holding devicefor screwdriver blade046.256


046.258 Screwdriver handlefor screwdriver blade046.256

Length 100 mm Al/Stainlesssteel

SURG

ERY

SURGERY

SURG

ERY

23


SURG

ERY

SURGERY

STRAUMANN® CARES® GUIDED SURGERY

SURG

ERY

25

SURG

ERY

26

STRAUMANN® CARES® GUIDED SURGERY – coDiagnostiX™


coDiagnostiX™ licences

019.0370 coDiagnostiX™ 8 PPP

019.0371 coDiagnostiX™ 8 PPG

019.0372 coDiagnostiX™ 8 Station

019.0373 coDiagnostiX™ 8 coDoctor™

coDiagnostiX™ units

019.0374 coDiagnostiX™ unit

Please contact your local Straumann representative for more information about coDiagnostiX™, upgrades, spare parts,manuals and different software modules.

SURG

ERY

27

STRAUMANN® CARES® GUIDED SURGERY – gonyX™


gonyX™

019.0201 Straumann® gonyX™

019.0212 NSK® handpiece forgonyX™

019.0213 NSK® control unit EU

019.0216 NSK® control unit NA

gonyX™ consumables

034.056-04 Closing lidfor sleeve positioner, forØ 2.8 mm sleeves

Ø 2.8 mm PEEK

034.057 Sleeve positionerfor gonyX™, forØ 2.8 mm sleeves

Ø 2.8 mm TAN

034.058-04 Closing lidfor sleeve positioner, forØ 5 mm sleeves

Ø 5 mm PEEK

034.059 Sleeve positionerfor gonyX™, for Ø 5 mmsleeves

Ø 5 mm TAN

034.064-03 Reference pinfor templiX reference plate

Length 7 mm,Ø 2 mm

Ti

034.066 gonyX™ drill set Ø 3 mm,Ø 3.8 mm,Ø 4.6 mm,Ø 5.4 mm,Ø 6.3 mm

Stainlesssteel

Please contact your local Straumann representative for more information about the gonyX™, consumables and spareparts.

Straumann® CARES® Guided Surgery – Guided surgery kit and guided implantsPlease find more information on the Guided Surgery kit in the section “Surgical Instruments” on p. 65 ff. Details on theguided implants can be found in the implant section on p. 32 ff.

SURG

ERY

28

STRAUMANN® CARES® GUIDED SURGERY – gonyX™


gonyX™ consumables

034.061 Stepped drillfor Ø 5 mm sleeves

Ø 5 mm,Ø 6.3 mm,Ø 7.3 mm

Stainlesssteel

034.060 Stepped drillfor Ø 2.8 mm sleeves

Ø 2.8 mm,Ø 3.8 mm,Ø 4.6 mm

Stainlesssteel

034.062-03 templiX reference plate Polymer

034.069V5 Girrbach Splitex® Counterplate

Please contact your local Straumann representative for more information about the gonyX™, consumables and spareparts.

Straumann® CARES® Guided Surgery – Guided surgery kit and guided implantsPlease find more information on the Guided Surgery kit in the section “Surgical Instruments” on p. 65 ff. Details on theguided implants can be found in the implant section on p. 32 ff.

SURG

ERY

SURGERY

SURGICAL PLANNING AIDS

SURG

ERY

29

SURG

ERY

30



049.076V4 X-ray reference sphere Ø 5 mm Stainlesssteel

150.215 X-ray templatesfor Standard and StandardPlus implants

Plastic

150.230 X-ray templatesfor Tapered Effect implants

Plastic

150.216 X-ray templatesfor Bone Level implants

Plastic

046.147 Diagnostic Tauxiliary instrument fordiagnosis

Length 65 mm,Width 33 mm

Ti

046.148 Standard, Standard Plusand Tapered Effect implantdistance indicator

Length 100 mm Ti/Stainlesssteel

026.0901 Bone Level implantdistance indicator

Length 100 mm Ti/Stainlesssteel

SURG

ERY

31



Components for fabricating an individual drill template

049.810V4 Drill sleeve with collar Height 10 mm,Inner Ø 2.4 mm,Outer Ø 3.5 mm

Ti

049.818V4 Stepped pinfor 049.810V4

Height 16 mm,Ø 2.2/3.5 mm

Ti

049.816V4 Pinfor 049.810V4

Height 16 mm,Ø 2.2 mm

Ti

049.817V4 Pinfor 049.810V4


Ti

049.819V4 Pinfor 049.810V4


Ti

Standard Implants RN RN RN WNØ 4.8 mm Ø 4.8 mm Ø 4.8 mm Ø 6.5 mm

Ø 3.3 mm Ø 4.1 mm Ø 4.8 mm Ø 4.8 mm

SLActive® S Ø 3.3 RN S Ø 4.1 RN S Ø 4.8 RN S Ø 4.8 WN 6 mm – 033.030S 033.230S 033.630S 8 mm 033.131S 033.031S* 033.231S 033.631S 10 mm 033.132S 033.032S* 033.232S 033.632S 12 mm 033.133S 033.033S* 033.233S 033.633S 14 mm 033.134S 033.034S 033.234S – 16 mm 033.135S 033.035S – –

2.8 mm

Standard Plus Implants NN RN RN RN WNØ 3.5 mm Ø 4.8 mm Ø 4.8 mm Ø 4.8 mm Ø 6.5 mm

Ø 3.3 mm Ø 3.3 mm Ø 4.1 mm Ø 4.8 mm Ø 4.8 mm

SLActive® SP Ø 3.3 NN SP Ø 3.3 RN SP Ø 4.1 RN SP Ø 4.8 RN SP Ø 4.8 WN 6 mm – 033.050S 033.250S 033.650S 8 mm 033.951S 033.151S 033.051S* 033.251S* 033.651S 10 mm 033.952S 033.152S 033.052S* 033.252S* 033.652S 12 mm 033.953S 033.153S 033.053S* 033.253S* 033.653S 14 mm 033.954S 033.154S 033.054S 033.254S –

1.8 mm

Tapered Effect Implants RN RN WNØ 4.8 mm Ø 4.8 mm Ø 6.5 mm

Ø 3.3 mm Ø 4.1 mm Ø 4.8 mm

SLActive® TE Ø 3.3 RN TE Ø 4.1 RN TE Ø 4.8 WN 8 mm 033.721S 033.761S* – 10 mm 033.722S 033.762S* 033.712S 12 mm 033.723S 033.763S* 033.713S 14 mm 033.724S 033.764S 033.714S

1.8 mm

Bone Level Implants NC RC RCØ 3.3 mm Ø 4.1 mm Ø 4.8 mm

Ø 3.3 mm Ø 4.1 mm Ø 4.8 mm

SLActive® BL Ø 3.3 NC BL Ø 4.1 RC BL Ø 4.8 RC 8 mm 021.2108 021.4108* 021.6108* 10 mm 021.2110 021.4110* 021.6110* 12 mm 021.2112 021.4112* 021.6112* 14 mm 021.2114 021.4114 021.6114

* Implant available as guided implant. For details, see implant list p. 37 ff.

SURG

ERY

OVERVIEW TITANIUM IMPLANTSSLActive® IMPLANTS

32

Standard Implants RN RN RN WNØ 4.8 mm Ø 4.8 mm Ø 4.8 mm Ø 6.5 mm

Ø 3.3 mm Ø 4.1 mm Ø 4.8 mm Ø 4.8 mm

SLA® S Ø 3.3 RN S Ø 4.1 RN S Ø 4.8 RN S Ø 4.8 WN 6 mm – 043.030S 043.230S 043.630S 8 mm 043.131S 043.031S 043.231S 043.631S 10 mm 043.132S 043.032S 043.232S 043.632S 12 mm 043.133S 043.033S 043.233S 043.633S 14 mm 043.134S 043.034S 043.234S – 16 mm 043.135S 043.035S – –

2.8 mm

Standard Plus Implants NN RN RN RN WNØ 3.5 mm Ø 4.8 mm Ø 4.8 mm Ø 4.8 mm Ø 6.5 mm

Ø 3.3 mm Ø 3.3 mm Ø 4.1 mm Ø 4.8 mm Ø 4.8 mm

SLA® SP Ø 3.3 NN SP Ø 3.3 RN SP Ø 4.1 RN SP Ø 4.8 RN SP Ø 4.8 WN 6 mm – – 043.050S 043.250S 043.650S 8 mm 042.930S 043.151S 043.051S 043.251S 043.651S 10 mm 042.931S 043.152S 043.052S 043.252S 043.652S 12 mm 042.932S 043.153S 043.053S 043.253S 043.653S 14 mm 042.933S 043.154S 043.054S 043.254S –

1.8 mm

Tapered Effect Implants RN RN WNØ 4.8 mm Ø 4.8 mm Ø 6.5 mm

Ø 3.3 mm Ø 4.1 mm Ø 4.8 mm

SLA® TE Ø 3.3 RN TE Ø 4.1 RN TE Ø 4.8 WN 8 mm 043.721S 043.761S – 10 mm 043.722S 043.762S 043.712S 12 mm 043.723S 043.763S 043.713S 14 mm 043.724S 043.764S 043.714S

1.8 mm

Bone Level Implants NC RC RCØ 3.3 mm Ø 4.1 mm Ø 4.8 mm

Ø 3.3 mm Ø 4.1 mm Ø 4.8 mm

SLA® BL Ø 3.3 NC BL Ø 4.1 RC BL Ø 4.8 RC 8 mm 021.2408 021.4408 021.6408 10 mm 021.2410 021.4410 021.6410 12 mm 021.2412 021.4412 021.6412 14 mm 021.2414 021.4414 021.6414

SURG

ERY

OVERVIEW TITANIUM IMPLANTSSLA® IMPLANTS

33

Standard Implants RNØ 4.8 mm

Ø 3.3 mm

SLActive® S Ø 3.3 RN 8 mm 033.431S* 10 mm 033.432S* 12 mm 033.433S* 14 mm 033.434S 16 mm 033.435S

2.8 mm

Standard Plus Implants NNC RNØ 3.5 mm Ø 4.8 mm

Ø 3.3 mm Ø 3.3 mm

SLActive® SP Ø 3.3 NNC SP Ø 3.3 RN 8 mm 033.416S 033.451S* 10 mm 033.417S 033.452S* 12 mm 033.418S 033.453S* 14 mm 033.419S 033.454S

1.8 mm

Tapered Effect Implants RNØ 4.8 mm

Ø 3.3 mm

SLActive® TE Ø 3.3 RN 8 mm 033.751S 10 mm 033.752S 12 mm 033.753S 14 mm 033.754S

1.8 mm

Bone Level Implants NCØ 3.3 mm

Ø 3.3 mm

SLActive® BL Ø 3.3 NC 8 mm 021.2208 10 mm 021.2210 12 mm 021.2212 14 mm 021.2214

* Implant available as guided implant. For details, see implant list p. 37 ff.

SURG

ERY

OVERVIEW ROXOLID® IMPLANTSSLActive® IMPLANTS

34

SURG

ERY

SURGERY

STANDARD IMPLANTS

SURG

ERY

35

SURG

ERY

36

STANDARD IMPLANTS Ø 3.3 mmREGULAR NECK Ø 4.8 mm


SLActive®

033.131S Standard implant SLActive® 8 mm Ti





SLA®

043.131S Standard implant SLA® 8 mm Ti





Closure screws and healing caps

048.371048.371V4

RN Closure screwsmall

Ti

048.373048.373V4

RN Closure screwlarge

Height 1.5 mm Ti

048.033 RN Healing cap Height 2 mm Ti


048.037 RN Healing cap Height 4.5 mm Ti

SURG

ERY

37

STANDARD ROXOLID® IMPLANTS Ø 3.3 mmREGULAR NECK Ø 4.8 mm


SLActive®

033.431S Standard implant SLActive® 8 mm TiZr





SLActive®, guided

033.431G Standard implantguided

SLActive® 8 mm TiZr






048.371048.371V4


Ti

048.373048.373V4


Height 1.5 mm Ti




SURG

ERY

38



SLActive®







SLA®







SLActive®, guided


SLActive® 8 mm Ti


SLActive® 10 mm Ti


SLActive® 12 mm Ti


048.371048.371V4


Ti

048.373048.373V4


Height 1.5 mm Ti




SURG

ERY

39



SLActive®






SLA®







048.371048.371V4


Ti

048.373048.373V4


Height 1.5 mm Ti




SURG

ERY

40

STANDARD IMPLANTS Ø 4.8 mmWIDE NECK Ø 6.5 mm


SLActive®





SLA®






048.375 WN Closure screw Ti

048.030 WN Healing caplabial bevel

Height 2 mm Ti

048.038 WN Healing cap Height 2 mm Ti


048.053 WN Healing cap Height 4.5 mm Ti

SURG

ERY

SURGERY

STANDARD PLUS IMPLANTS

SURG

ERY

41

SURG

ERY

42

STANDARD PLUS IMPLANTS Ø 3.3 mmNARROW NECK CrossFit® Ø 3.5 mm


SLActive®

033.416S Standard Plus Implant SLActive® 8 mm TiZr





048.324048.324V4

NNC Closure screw Height 0 mm Ti

048.325048.325V4

NNC Closure screw Height 1.5 mm Ti

048.071 NNC Healing capreduced height

Height 3 mm Ti

048.074 NNC Healing capregular height

Height 4.5 mm Ti

048.082 NNC Healing caplabial bevel

Height 2 mm Ti

NoteNNC products may not be available in all countries, subject to regulatory approval and market release. Please checkwith your local Straumann sales representative for more information.

SURG

ERY

43

STANDARD PLUS IMPLANTS Ø 3.3 mmNARROW NECK Ø 3.5 mm


SLActive®

033.951S Standard Plus implant SLActive® 8 mm Ti




SLA®

042.930S Standard Plus implant SLA® 8 mm Ti




Healing and protective caps

048.043 NN Healing capwith integral occlusalscrew

Height 3.4 mm Ti/Ti alloy

048.374 NN Closure screwwith hex socket*

Height 1.8 mm Ti

048.050 NN Protective capwith integral occlusalscrew

Height 3.4 mm PEEK/TAN

* = Requires hexagonal screwdriver, Art. No. 046.421

SURG

ERY

44

STANDARD PLUS IMPLANTS Ø 3.3 mmREGULAR NECK Ø 4.8 mm


SLActive®





SLA®






048.371048.371V4


Ti

048.373048.373V4


Height 1.5 mm Ti




048.028 RN Healing caplabial bevel, small

Height 2 mm Ti

048.029 RN Healing caplabial bevel, large

Height 3.5 mm Ti

SURG

ERY

45

STANDARD PLUS ROXOLID® IMPLANTS Ø 3.3 mmREGULAR NECK Ø 4.8 mm


SLActive®

033.451S Standard Plus implant SLActive® 8 mm TiZr




SLActive®, guided

033.451G Standard Plus implantguided







048.371048.371V4


Ti

048.373048.373V4


Height 1.5 mm Ti





Height 2 mm Ti


Height 3.5 mm Ti

SURG

ERY

46



SLActive®






SLA®






SLActive®, guided


SLActive® 8 mm Ti


SLActive® 10 mm Ti


SLActive® 12 mm Ti


048.371048.371V4


Ti

048.373048.373V4


Height 1.5 mm Ti





Height 2 mm Ti


Height 3.5 mm Ti

SURG

ERY

47



SLActive®






SLA®






SLActive®, guided


SLActive® 8 mm Ti


SLActive® 10 mm Ti


SLActive® 12 mm Ti


048.371048.371V4


Ti

048.373048.373V4


Height 1.5 mm Ti





Height 2 mm Ti


Height 3.5 mm Ti

SURG

ERY

48

STANDARD PLUS IMPLANTS Ø 4.8 mmWIDE NECK Ø 6.5 mm


SLActive®





SLA®








Height 2 mm Ti




SURG

ERY

SURGERY

TAPERED EFFECT IMPLANTS

SURG

ERY

49

SURG

ERY

50

TAPERED EFFECT IMPLANTS Ø 3.3 mmREGULAR NECK Ø 4.8 mm


SLActive®

033.721S Tapered Effect implant SLActive® 8 mm Ti




SLA®

043.721S Tapered Effect implant SLA® 8 mm Ti





048.371048.371V4


Ti

048.373048.373V4


Height 1.5 mm Ti





Height 2 mm Ti


Height 3.5 mm Ti

SURG

ERY

51

TAPERED EFFECT ROXOLID® IMPLANTS Ø 3.3 mmREGULAR NECK Ø 4.8 mm


SLActive®

033.751S Tapered Effect implant SLActive® 8 mm TiZr





048.371048.371V4


Ti

048.373048.373V4


Height 1.5 mm Ti





Height 2 mm Ti


Height 3.5 mm Ti

SURG

ERY

52

TAPERED EFFECT IMPLANTS Ø 4.1 mmREGULAR NECK Ø 4.8 mm


SLActive®





SLA®





SLActive®, guided

033.761G Tapered Effect implantguided

SLActive® 8 mm Ti


SLActive® 10 mm Ti


SLActive® 12 mm Ti


048.371048.371V4


Ti

048.373048.373V4


Height 1.5 mm Ti





Height 2 mm Ti


Height 3.5 mm Ti

SURG

ERY

53

TAPERED EFFECT IMPLANTS Ø 4.8 mmWIDE NECK Ø 6.5 mm


SLActive®




SLA®







Height 2 mm Ti




SURG

ERY

SURGERY

BONE LEVEL IMPLANTS

SURG

ERY

55

SURG

ERY

56

BONE LEVEL IMPLANTS Ø 3.3 mmNARROW CrossFit®


SLActive®

021.2108 Bone Level implant SLActive® 8 mm Ti




SLA®

021.2408 Bone Level implant SLA® 8 mm Ti




Closure screws and healing abutments

024.2100-04 NC Closure screw* Height 0 mm Ti

024.2105-04 NC Closure screw* Height 0.5 mm Ti

024.2222 NC Healing abutmentconical shape


Ti


Height 3.5 mm,Ø 3.6 mm

Ti



Ti



Ti



Ti



Ti

024.2234 NC Healing abutmentbottle shape


Ti



Ti

024.2270 NC Healing abutmentcustomizable

Ø 5 mm PEEK

* = Bone Level closure screws are delivered sterile and ready to use.

SURG

ERY

57

BONE LEVEL ROXOLID® IMPLANTS Ø 3.3 mmNARROW CrossFit®


SLActive®

021.2208 Bone Level implant SLActive® 8 mm TiZr





024.2100-04 NC Closure screw* Height 0 mm Ti

024.2105-04 NC Closure screw* Height 0.5 mm Ti



Ti



Ti



Ti



Ti



Ti



Ti



Ti



Ti

024.2270 NC Healing abutmentcustomizable

Ø 5 mm PEEK


SURG

ERY

58

BONE LEVEL IMPLANTS Ø 4.1 mmREGULAR CrossFit®


SLActive®





SLA®





SLActive®, guided

021.4108G Bone Level implantguided

SLActive® 8 mm Ti


SLActive® 10 mm Ti


SLActive® 12 mm Ti


024.4100-04 RC Closure screw* Height 0 mm Ti

024.4105-04 RC Closure screw* Height 0.5 mm Ti

024.4222 RC Healing abutmentconical shape


Ti



Ti



Ti


Height 2 mm,Ø 6 mm

Ti


Height 4 mm,Ø 6 mm

Ti


Height 6 mm,Ø 6 mm

Ti


SURG

ERY

59




024.4234 RC Healing abutmentbottle shape


Ti



Ti

024.4270 RC Healing abutmentcustomizable

Ø 7 mm PEEK

SURG

ERY

60



SLActive®





SLA®





SLActive®, guided


SLActive® 8 mm Ti


SLActive® 10 mm Ti


SLActive® 12 mm Ti


024.4100-04 RC Closure screw* Height 0 mm Ti

024.4105-04 RC Closure screw* Height 0.5 mm Ti



Ti



Ti



Ti


Height 2 mm,Ø 6 mm

Ti


Height 4 mm,Ø 6 mm

Ti


Height 6 mm,Ø 6 mm

Ti


SURG

ERY

61






Ti



Ti

024.4270 RC Healing abutmentcustomizable

Ø 7 mm PEEK

SURG

ERY

SURGERY

TEMPIMPLANTS

SURG

ERY

63

SURG

ERY

64

TEMPIMPLANTS


Implants

80371SV4 TempImplant Ø 2 mm,Thread 10 mm

Ti alloy

80372SV4 TempImplant Ø 2 mm,Thread 12 mm

Ti alloy

Auxiliary parts

80381 Drill Length 37 mm,Ø 1.5 mm

Stainlesssteel

80363 TempImplant insertingdevicemechanical

Stainlesssteel

80398 TempImplant insertingdevicemanual

Stainlesssteel

80356 TempImplant bending tool Stainlesssteel

048.109 Transfer pinfor retentive anchor*


Dalbo®-Rotex® Matrix

80399V4 Dalbo®-Rotex® Matrix PA

* = The geometry of the spherical head and square base corresponds to the geometry of the retentive anchor (Art. No. 048.439).

SURG

ERY

SURGERY

SURGICAL INSTRUMENTS

SURG

ERY

65

SURG

ERY

66

SURGICAL INSTRUMENTSSINGLE-PATIENT DRILLS (DRILL STOP COMPATIBLE)


040.440S Drill setshort, drill stop compatiblewith Ø 3.3 mm implant,single-patient use, sterile

Ø 2.2 mm,Ø 2.8 mm,Length 33 mm

Stainlesssteel

040.441S Drill setlong, drill stop compatiblewith Ø 3.3 mm implant,single-patient use, sterile

Ø 2.2 mm,Ø 2.8 mm,Length 41 mm

Stainlesssteel


Ø 2.2 mm,Ø 2.8 mm,Ø 3.5 mm,Length 33 mm

Stainlesssteel


Ø 2.2 mm,Ø 2.8 mm,Ø 3.5 mm,Length 41 mm

Stainlesssteel


Ø 2.2 mm,Ø 2.8 mm,Ø 3.5 mm,Ø 4.2 mm,Length 33 mm

Stainlesssteel


Ø 2.2 mm,Ø 2.8 mm,Ø 3.5 mm,Ø 4.2 mm,Length 41 mm

Stainlesssteel

IndicationSingle-patient drills are indicated for all implant bed preparation procedures with the Straumann® Dental ImplantSystem. They are supplied sterile-packed and must only be used for one patient and one surgery. Single-patient drillscan minimize the infection risk for patients, and their color coding simplifies implant bed preparation.

WarningSingle-patient drills cannot be resterilized! Resterilization renders these drills unusable.

SURG

ERY

67

SURGICAL INSTRUMENTSSTRAUMANN® DRILL STOP

Art. No. Article

040.460 Drill stop kit3 x drill stop set, type A,3 x drill stop set, type B,3 x drill stop set, type C,3 x drill stop set, type D,1 x drill stop aid

040.454S Refill package: Drill stop settype A, for short drill 12 mm/long drill 16 mm,Ø 3.3/4.1/4.8 mm implants

040.455S Refill package: Drill stop settype B, for short drill 10 mm/long drill 14 mm,Ø 3.3/4.1/4.8 mm implants

040.456S Refill package: Drill stop settype C, for short drill 8 mm/long drill 12 mm,Ø 3.3/4.1/4.8 mm implants

040.457S Refill package: Drill stop settype D, for short drill 6 mm/long drill 10 mm,Ø 3.3/4.1/4.8 mm implants

040.461 Drill stop aid

The Straumann® Drill Stop provides precise control over drilling depth during implant bed preparation for theplacement of Straumann® dental implants. Delivered in sterile sets, the drill stops are ready to use. The Straumann® Drill Stop is designed for single-patient use only and must be used in conjunction with the single-patient drillsspecifically designed for them.

Each Straumann® Drill Stop set includes drill stops with the following diameters:Ø 2.2 mm (blue), Ø 2.8 mm (yellow), Ø 3.5 mm (red),Ø 4.2 mm (green). These diameters correspond to the diameters of the Straumann® drills.

ImportantStraumann® drill stops are not indicated for:● Extraction sites, where bone cavity is often wider than the diameter necessary to hold the drill stop.● Use with drill templates, due to the interference from or with the template.

SURG

ERY

68

SURGICAL INSTRUMENTSSTRAUMANN® GUIDED SURGERY


Guided milling cutters

034.215 Milling cutterguided

Length 32.5 mm,Ø 2.8 mm

Stainlesssteel



Stainlesssteel



Stainlesssteel

Guided pilot drills

034.123 Pilot drillshort, guided

Length 32 mm,Ø 2.2 mm

Stainlesssteel

034.126 Pilot drilllong, guided


Stainlesssteel

034.129 Pilot drillextra-long, guided


Stainlesssteel

Guided twist drills

034.223 Twist drill PROshort, guided


Stainlesssteel

034.226 Twist drill PROlong, guided


Stainlesssteel

034.229 Twist drill PROextra-long, guided


Stainlesssteel



Stainlesssteel



Stainlesssteel



Stainlesssteel

SURG

ERY

69



Guided twist drills



Stainlesssteel



Stainlesssteel



Stainlesssteel

Stop key

034.006 Stop key Stainlesssteel

Guided mucosa punches

034.010 Mucosa punchguided


Stainlesssteel


Length 30 mm,Ø 4 mm

Stainlesssteel



Stainlesssteel

SURG

ERY

70



Guided profile drills

034.235 SP Profile drillguided

Regular Neck,Length 35 mm,Ø 3.3 mm

Stainlesssteel

034.435 SP Profile drillguided


Stainlesssteel

034.237 TE Profile drillguided


Stainlesssteel

034.437 TE Profile drillguided


Stainlesssteel

026.2503 BL/NNC Profile drillguided


Stainlesssteel

026.4503 BL Profile drillguided


Stainlesssteel

026.6503 BL Profile drillguided


Stainlesssteel

Important Do not use SP Profile drills with Standard Plus implants Ø 3.3 mm, NNC/NN, or with Standard Plus implantsØ 4.8 mm, RN. For SP NNC Ø 3.3 mm implants, use the 026.2510 BL/TE/NNC Tap for handpiece, guided, forpre-tapping the implant bed for NNC implants.

SURG

ERY

71



Guided taps

034.245 S/SP Tapfor handpiece, guided


Stainlesssteel



Stainlesssteel



Stainlesssteel

026.2510 BL/TE/NNC Tapfor handpiece, guided


Stainlesssteel

026.4510 BL/TE Tapfor handpiece, guided


Stainlesssteel

026.6510 BL/TE Tapfor handpiece, guided


Stainlesssteel

Important Do not use SP Profile drills with Standard Plus implants Ø 3.3 mm, NNC/NN, or with Standard Plus implantsØ 4.8 mm, RN. For SP NNC Ø 3.3 mm implants, use the 026.2510 BL/TE/NNC Tap for handpiece, guided, forpre-tapping the implant bed for NNC implants.

SURG

ERY

72



Auxiliary parts

034.150 Drill handleØ 2.2 mm

Stop 1/3 mm,Ø 2.2 mm

Stainlesssteel



Stainlesssteel



Stainlesssteel



Stainlesssteel

034.750 C-handle H2 Stainlesssteel



034.005 Connectorfor ratchet

Stainlesssteel

034.256 Template fixation pinguided

Ø 2.8/2.8 mm Stainlesssteel


Ø 5/2.8 mm Stainlesssteel





SURG

ERY

73



Sleeves for Straumann® Guided Surgery

034.050V4 Sleeve Height 5 mm,Ø 5 mm

Stainlesssteel

034.052V4 Sleeve Height 6 mm,Ø 2.8 mm

Stainlesssteel

034.053V4 T-sleeve Height 5 mm,Ø 5 mm

Stainlesssteel

034.055V4 T-sleeve Height 6 mm,Ø 2.8 mm

Stainlesssteel

Guided surgery cassette

034.001 Surgical cassettefor Straumann® GuidedSurgery*


* = For extra grommets please contact your local Straumann sales representative.

SURG

ERY

74

SURGICAL INSTRUMENTSFOR STANDARD AND STANDARD PLUS IMPLANTS (EXCEPT NNC),ENDOSTEAL Ø 3.3 mm


Basic implant bed preparation for Standard and Standard Plus implants Ø 3.3 mm

044.022 Round bur Ø 1.4 mm Stainlesssteel



044.210 Pilot drill 1short


Stainlesssteel

044.211 Pilot drill 1long


Stainlesssteel

046.458 Alignment pin Length 28 mm,Ø 2.2 mm

Ti



Stainlesssteel



Stainlesssteel

046.455 Depth gaugewith distance indicator

Length 27 mm,Ø 2.2/2.8 mm

Ti

Fine implant bed preparation for Standard Plus implants Ø 3.3 mm

044.086 SP Profile drillshort


Stainlesssteel

044.087 SP Profile drilllong


Stainlesssteel

SP Profile drills are used for preparing the shoulder configuration of Standard Plus implants in the bone.Important: Do not use SP Profile drills with Standard Plus implants Ø 3.3 mm, NNC/NN, or with Standard Plus im-plants Ø 4.8 mm, RN.

Fine implant bed preparation for Standard and Standard Plus implants Ø 3.3 mm

044.575 S/SP Tapfor adapter


Stainlesssteel/PEEK

S/SP Taps are used for pre-tapping the implant bed for Standard and Standard Plus implants (except NNC).Important: For S and SP Ø 3.3 mm implants, pre-tapping is recommended in dense bone (class* 1 and 2).For SP NNC Ø 3.3 mm implants, use the BL/TE/NNC Tap for adaptor for pre-tapping the implant bed for NNCimplants.

*Class 1: hardest bone/Class 4: softest bone

SURG

ERY

75

SURGICAL INSTRUMENTSFOR STANDARD AND STANDARD PLUS IMPLANTS, ENDOSTEAL Ø 4.1 mm








Stainlesssteel



Stainlesssteel


Ti



Stainlesssteel



Stainlesssteel



Ti

044.250 Twist drill PROshort


Stainlesssteel

044.251 Twist drill PROlong


Stainlesssteel

046.450 Depth gauge Length 26 mm,Ø 3.5 mm

Ti

SURG

ERY

76

SURGICAL INSTRUMENTSFOR STANDARD AND STANDARD PLUS IMPLANTS,ENDOSTEAL Ø 4.1 mm





Stainlesssteel



Stainlesssteel

SP Profile drills are used for preparing the shoulder configuration of Standard Plus implants in the bone.Important: Do not use SP Profile drills with Standard Plus Implants Ø 3.3 mm, NN, or with Standard Plus ImplantsØ 4.8 mm, RN.




Stainlesssteel/PEEK

S/SP Taps are used for pre-tapping the implant bed for Standard and Standard Plus implants.Important: For S and SP Ø 4.1 mm implants, pre-tapping is recommended in dense bone (class* 1 and 2).


SURG

ERY

77

SURGICAL INSTRUMENTSFOR STANDARD AND STANDARD PLUS IMPLANTS, ENDOSTEAL Ø 4.8 mm








Stainlesssteel



Stainlesssteel


Ti



Stainlesssteel



Stainlesssteel



Ti



Stainlesssteel



Stainlesssteel


Ti



Stainlesssteel



Stainlesssteel


Ti

SURG

ERY

78

SURGICAL INSTRUMENTSFOR STANDARD AND STANDARD PLUS IMPLANTS,ENDOSTEAL Ø 4.8 mm




Wide Neck,Length 25 mm,Ø 4.2 mm

Stainlesssteel



Stainlesssteel

SP Profile drills are used for preparing the shoulder configuration of Standard Plus implants in the bone.Important: Do not use SP Profile drills with Standard Plus Implants Ø 3.3 mm, NN, or with Standard Plus ImplantsØ 4.8 mm, RN.




Stainlesssteel/PEEK

S/SP Taps are used for pre-tapping the implant bed for Standard and Standard Plus implants.Important: For S and SP Ø 4.8 mm implants, pre-tapping is recommended over the full depth in all bone classes.

SURG

ERY

79

SURGICAL INSTRUMENTSFOR TAPERED EFFECT IMPLANTS, ENDOSTEAL Ø 3.3 mm


Basic implant bed preparation for Tapered Effect implants Ø 3.3 mm






Stainlesssteel



Stainlesssteel


Ti



Stainlesssteel



Stainlesssteel



Ti

SURG

ERY

80



Fine implant bed preparation for Tapered Effect implants Ø 3.3 mm

044.701 TE Profile drillshort


Stainlesssteel

044.708 TE Profile drilllong


Stainlesssteel

TE Profile drills are used for preparing the implant bed for the coronal conical core of Tapered Effect implants.Important: To be used in all bone classes.

Fine implant bed preparation for Bone Level and Tapered Effect implants Ø 3.3 mm

026.2310 BL/TE/NNC Tap foradapter


Stainlesssteel/PEEK

BL/TE/NNC Taps are used for pre-tapping the implant bed for Bone Level, Tapered Effect and Narrow Neck Cross-Fit® implants.Important: For TE Ø 3.3 mm implants, pre-tapping is recommended over the full depth in bone class* 1 and 2.


SURG

ERY

81









Stainlesssteel



Stainlesssteel


Ti



Stainlesssteel



Stainlesssteel



Ti



Stainlesssteel



Stainlesssteel


Ti

SURG

ERY

82






Stainlesssteel



Stainlesssteel



026.4310 BL/TE Tap for adapter Length 23 mm,Ø 4.1 mm

Stainlesssteel/PEEK

BL/TE Taps are used for pre-tapping the implant bed for Bone Level and Tapered Effect implants.Important: For TE Ø 4.1 mm implants, pre-tapping is recommended over the full depth in bone class* 1 and 2.


SURG

ERY

83









Stainlesssteel



Stainlesssteel


Ti



Stainlesssteel



Stainlesssteel



Ti



Stainlesssteel



Stainlesssteel


Ti



Stainlesssteel



Stainlesssteel


Ti

SURG

ERY

84






Stainlesssteel



Stainlesssteel




Stainlesssteel/PEEK

BL/TE Taps are used for pre-tapping the implant bed for Bone Level and Tapered Effect implants.Important: For TE Ø 4.8 mm implants pre-tapping is recommended over the full depth in all bone classes.

SURG

ERY

85

SURGICAL INSTRUMENTSFOR BONE LEVEL AND NARROW NECK CrossFit® IMPLANTS,ENDOSTEAL Ø 3.3 mm


Basic implant bed preparation for Bone Level implants Ø 3.3 mm






Stainlesssteel



Stainlesssteel


Ti



Stainlesssteel



Stainlesssteel



Ti

SURG

ERY

86

SURGICAL INSTRUMENTSFOR BONE LEVEL AND NARROW NECK CrossFit® IMPLANTS,ENDOSTEAL Ø 3.3 mm


Fine implant bed preparation for Bone Level and Narrow Neck CrossFit® implants Ø 3.3 mm

026.2303 BL/NNC Profile drillshort


Stainlesssteel

026.2306 BL/NNC Profile drilllong


Stainlesssteel

BL/NNC Profile drills are used for preparing the implant bed for the coronal conical core of Bone Level andNarrow Neck CrossFit® implants.Important: To be used in all bone classes.

Fine implant bed preparation for Bone Level, Tapered Effect and Narrow Neck CrossFit® implants Ø 3.3 mm

026.2310 BL/TE/NNC Tap foradapter


Stainlesssteel/PEEK

BL/TE/NNC Taps are used for pre-tapping the implant bed for Bone Level, Tapered Effect and Narrow Neck Cross-Fit® implants.Important: For BL/NNC Ø 3.3 mm implants, pre-tapping is recommended over the full depth in bone class* 1and 2.


SURG

ERY

87

SURGICAL INSTRUMENTSFOR BONE LEVEL IMPLANTS, ENDOSTEAL Ø 4.1 mm








Stainlesssteel



Stainlesssteel


Ti



Stainlesssteel



Stainlesssteel



Ti



Stainlesssteel



Stainlesssteel


Ti

SURG

ERY

88



Fine implant bed preparation for Bone Level implants Ø 4.1 mm

026.4303 BL Profile drillshort


Stainlesssteel

026.4306 BL Profile drilllong


Stainlesssteel

BL Profile drills are used for preparing the implant bed for the coronal conical core of Bone Level implants.Important: To be used in all bone classes.



Stainlesssteel/PEEK

BL/TE Taps are used for pre-tapping the implant bed for Bone Level and Tapered Effect implants.Important: For BL Ø 4.1 mm implants, pre-tapping is recommended over the full depth in bone class* 1 and 2.


SURG

ERY

89









Stainlesssteel



Stainlesssteel


Ti



Stainlesssteel



Stainlesssteel



Ti



Stainlesssteel



Stainlesssteel


Ti



Stainlesssteel



Stainlesssteel


Ti

SURG

ERY

90



Fine implant bed preparation for Bone Level implants Ø 4.8 mm

026.6303 BL Profile drillshort


Stainlesssteel

026.6306 BL Profile drilllong


Stainlesssteel

BL Profile drills are used for preparing the implant bed for the coronal conical core of Bone Level implants.Important: To be used in all bone classes.



Stainlesssteel/PEEK

BL/TE Taps are used for pre-tapping the implant bed for Bone Level and Tapered Effect implants.Important: For BL Ø 4.8 mm implants pre-tapping is recommended over the full depth for all bone classes.

SURG

ERY

91

SURGICAL INSTRUMENTSFOR STANDARD AND STANDARD PLUS IMPLANTS Ø 4.1 mmSTARTER SETS

Art. No. Article Material

Starter Sets contain instruments needed for placing Straumann® Standard and Standard Plus implants

040.320 Surgical instruments starter set, Ø 4.1 mmfor preparation by handconsisting of:044.210 Pilot drill 1, short, Ø 2.2 mm044.211 Pilot drill 1, long, Ø 2.2 mm044.214 Pilot drill 2, short, Ø 2.8 mm044.215 Pilot drill 2, long, Ø 2.8 mm044.218 Twist drill, short, Ø 3.5 mm044.219 Twist drill, long, Ø 3.5 mm044.592 S/SP Tap for ratchet, short,Ø 4.1 mm044.593 S/SP Tap for ratchet, long,Ø 4.1 mm046.458 Alignment pin, Ø 2.2 mm046.455 Depth gauge with distanceindicator, Ø 2.2/2.8 mm046.450 Depth gauge for Standard andStandard Plus implants Ø 4.1 mm

040.330 Surgical instruments starter set, Ø 4.1 mm,Tap for adapter, for preparation using thehandpiece,consisting of:044.210 Pilot drill 1, short, Ø 2.2 mm044.211 Pilot drill 1, long, Ø 2.2 mm044.214 Pilot drill 2, short, Ø 2.8 mm044.215 Pilot drill 2, long, Ø 2.8 mm044.218 Twist drill, short, Ø 3.5 mm044.219 Twist drill, long, Ø 3.5 mm044.577 S/SP Tap for adapter, Ø 4.1 mm046.458 Alignment pin, Ø 2.2 mm046.455 Depth gauge with distanceindicator, Ø 2.2/2.8 mm046.450 Depth gauge for Standard andStandard Plus implants Ø 4.1 mm

SURG

ERY

92

SURGICAL INSTRUMENTSFOR STANDARD AND STANDARD PLUS IMPLANTS Ø 4.8 mmSTARTER SETS


Starter Sets contain instruments needed for placing Straumann® Standard and Standard Plus implants

040.321 Surgical instruments starter set, Ø 4.8 mm,for preparation by handconsisting of:044.254 Twist drill PRO, short, Ø 4.2 mm044.255 Twist drill PRO, long, Ø 4.2 mm044.594 S/SP Tap for ratchet, short,Ø 4.8 mm044.595 S/SP Tap for ratchet, long,Ø 4.8 mm046.451 Depth gauge for Standard andStandard Plus implants Ø 4.8 mm

040.331 Surgical instruments starter set, Ø 4.8 mm,Tap for adapter, for preparation using thehandpiececonsisting of:044.254 Twist drill PRO, short, Ø 4.2 mm044.255 Twist drill PRO, long, Ø 4.2 mm044.579 S/SP Tap for adapter, Ø 4.8 mm046.451 Depth gauge for Standard andStandard Plus implants Ø 4.8 mm

SURG

ERY

93

SURGICAL INSTRUMENTSFOR STRAUMANN® STANDARD, STANDARD PLUS AND TAPERED EFFECT IMPLANTSBONE PROFILE DRILLS


044.304 RN Bone profile drillfor use with 049.082

InnerØ 3.6/4.8 mm,Outer Ø 5.4 mm,Length 28 mm

Stainlesssteel

044.305 WN Bone profile drillfor use with 049.082

InnerØ 3.6/6.5 mm,Outer Ø 7.2 mm,Length 25 mm

Stainlesssteel

049.082 SCS Guiding cylinderfor Straumann® dentalimplants Ø 3.3 mm andØ 3.5 mm


Stainlesssteel

ImportantBone profile drills cannot be used for Straumann® Bone Level implants.The SCS Guiding cylinder is intended for single use only.

SURG

ERY

94

AUXILIARY INSTRUMENTS


046.110 Instrument tweezers Length 140 mm Stainlesssteel

046.095 Tweezerswith titanium plasma-coated tips

Length 115 mm Stainlesssteel/Ti

046.057 Tweezerswithout titanium plasma-coated tips


046.119 Ratchetincludes service instrument


046.108 Service instrumentfor ratchet


045.111V4 Cleaning brushfor ratchet


Stainlesssteel/Nylon

046.049 Torque control devicefor ratchet


046.064 Holding key Length 85 mm Stainlesssteel

046.460 Adapterfor ratchet, extra short


046.461 Adapterfor ratchet, short


046.462 Adapterfor ratchet, long


046.470 Adapterfor handpiece, extra short


046.471 Adapterfor handpiece, short


046.472 Adapterfor handpiece, long


SURG

ERY

95

AUXILIARY INSTRUMENTS


Screwdrivers

046.400 SCS Screwdriverfor ratchet, extra short

Length 15 mm Cronidur® 30

046.401 SCS Screwdriverfor ratchet, short


046.402 SCS Screwdriverfor ratchet, long


046.410 SCS Screwdriverfor handpiece, extra short


046.411 SCS Screwdriverfor handpiece, short


046.412 SCS Screwdriverfor handpiece, long


046.421 Hexagonal screwdriver Length 30 mm Stainlesssteel

045.921 Light curette for implants(5 per pack)*

* = See below for manufacturer details.

The SCS screwdrivers also act as inserting instruments for the WN Solid abutments, for all synOcta® abutments, for allCrossFit® prosthetic components as well as for all closure screws and healing caps in the Straumann® Dental ImplantSystem.

ManufacturerKerr Hawe SA

Zona StrecceCH-6934 BioggioSwitzerland

SURG

ERY

96

SURGICAL CASSETTE


Surgical cassette

040.165 Straumann® Surgicalcassetteincludes screw container041.047, withoutinstruments*


Plastic

041.047 Screw containerwith lid, for Straumann® surgical cassette, withoutscrews


Plastic

Ultrasonic Cleaning Cassette

040.175 Ultrasonic cleaningcassette


Plastic/Silicone

Storage system

041.500 Storage systemfor implants (SLA®/SLActive®), incl. drawersand dividers


PS

* = For extra grommets please contact your local Straumann sales representative.

SURG

ERY

97

OSTEOTOMESFOR BONE CONDENSATION


040.500 Osteotome instrument kitfor bone condensationkit contains:

Stainlesssteel/Plastic

046.500 Osteotomestraight, for bonecondensation

Ø 2.2 mm Stainlesssteel







046.510 Osteotomeangled, for bonecondensation








046.550 Depth stop Ø 2.2 mm Ti/Stainlesssteel




The instruments and depth stops are also available individually.

SURG

ERY

98

OSTEOTOMESFOR SINUS FLOOR ELEVATION


040.501 Osteotome instrument kitfor partial sinus floorelevationkit contains:

Stainlesssteel/Plastic

046.521 Osteotomestraight, for sinus floorelevation






046.531 Osteotomeangled, for sinus floorelevation









The instruments and depth stops are also available individually.

SURG

ERY

99

EXPLANTATIONEXPLANTATION DRILLS


044.330 Explantation drillshort, for Straumann® dental implantsØ 3.3 mm and Ø 3.5 mm

Length 32 mm,Inner Ø 3.6 mm,Outer Ø 4.2 mm

Stainlesssteel

044.331 Explantation drillmedium, for Straumann® dental implantsØ 3.3 mm and Ø 3.5 mm

Length 37.5 mm,Inner Ø 3.6 mm,Outer Ø 4.2 mm

Stainlesssteel

044.332 Explantation drilllong, for Straumann® dental implantsØ 3.3 mm and Ø 3.5 mm


Stainlesssteel

044.340 Explantation drillshort, for Straumann® dental implantsØ 4.1 mm


Stainlesssteel

044.341 Explantation drillmedium, for Straumann® dental implantsØ 4.1 mm


Stainlesssteel

044.342 Explantation drilllong, for Straumann® dental implantsØ 4.1 mm


Stainlesssteel

044.344 Explantation drillshort, for Straumann® dental implantsØ 4.8 mm


Stainlesssteel

044.345 Explantation drillmedium, for Straumann® dental implantsØ 4.8 mm


Stainlesssteel

044.346 Explantation drilllong, for Straumann® dental implantsØ 4.8 mm


Stainlesssteel

ImportantExplantation drills are intended for single use only.

SURG

ERY

100

EXPLANTATIONEXPLANTATION AIDS


Explantation of S/SP/TE implants without abutment

049.082 SCS Guiding cylinderfor Straumann® dental implantsØ 3.3 mm and Ø 3.5 mm


Stainlesssteel

049.083 SCS Guiding cylinderfor Straumann® dental implantsØ 4.1 mm


Stainlesssteel

049.167 SCS Guiding cylinderfor Straumann® dental implantsØ 4.8 mm


Stainlesssteel

049.182 SCS Guiding cylinderfor Straumann® dental implantsØ 3.3 mm Narrow Neck


Ti/Stainlesssteel

049.360 SCS Guiding cylinderfor Straumann® dental implantsØ 3.3 mm Narrow NeckCrossfit®

Length 10.1 mm Stainlesssteel

Explantation of Bone Level implants without abutment

026.2801 NC Guiding cylinderfor explantation of Ø 3.3 mmBone Level implants


Stainlesssteel

026.4801 RC Guiding cylinderfor explantation of Ø 4.1 mmBone Level implants


Stainlesssteel

026.6801 RC Guiding cylinderfor explantation of Ø 4.8 mmBone Level implants


Stainlesssteel

Explantation of S/SP/TE implants with abutment

049.850 RN Guiding sleevefor Straumann® dentalimplants, Ø 3.3 mm, cement-retained and screw-retained


Stainlesssteel

049.071 RN Guiding sleevefor Straumann® dentalimplants, Ø 4.1 mm andØ 3.5 mm, cement-retainedand screw-retained


Stainlesssteel

049.851 RN Guiding sleevefor Straumann® dentalimplants, Ø 4.8 mm, cement-retained and screw-retained


Stainlesssteel

ImportantThe explantation aids are intended for single use only.

SURG

ERY

101

EXPLANTATIONEXPLANTATION AIDS


Explantation of S/SP/TE implants with abutment

048.350048.350V4

SCS Occlusal screw Length 4 mm Ti

049.181 SCS Occlusal screwfor guiding sleeve and post fortemporary restoration

Length 7.6 mm Ti alloy

Explantation devices

026.2048 48h Explantation devicefor Bone Level NC Implants

Ø 8 mm,Length 31.4 mm

Stainlesssteel

026.4048 48h Explantation devicefor Bone Level RC Implants


Stainlesssteel

049.361 48h Explantation devicefor Soft Tissue Level NNCImplants


Stainlesssteel

049.362 48h Explantation devicefor Soft Tissue Level synOcta® implants, short


Stainlesssteel

049.363 48h Explantation devicefor Soft Tissue Level synOcta® implants, long


Stainlesssteel

ImportantThe explantation aids are intended for single use only.

SURG

ERY

102

OSSTELL™ MENTOR AUXILIARY COMPONENTS

Art. No. Article

174.021V5 Smartpeg™ Type 4for RN and WN (delivered sterile, disposable)

174.020V5 Smartpeg™ Type 17for NN (delivered sterile, disposable)

174.156V5 Smartpeg™ Type 42for RC (Bone Level, delivered sterile, disposable)

174.155V5 Smartpeg™ Type 41for NC (Bone Level, delivered sterile, disposable)

ImportantInstitut Straumann AG no longer distributes Osstell™ mentor instruments andaccessories. Please contact Osstell AB directly for orders.

Smartpeg™ is currently not available for Straumann® Narrow Neck CrossFit® implants.

0 4 0 2ManufacturerOsstell AB

Gamlestadsvägen 3BSE-415 02 GöteborgSweden

PRO

STH

ETICS

PROSTHETICS

PRO

STH

ETICS

103

Cassettes, inserts and storage system 104Prosthetic instruments 106Prosthetics for Straumann® Standard, Standard Plus and Tapered Effect Implants● Prosthetic planning aids 110● Straumann® CARES® Implant-borne elements 113● Crowns and bridges 119● Hybrid dentures 149Prosthetics for Straumann® Bone Level implants● Prosthetic planning aids 172● Straumann® CARES® Implant-borne elements 178● Crowns and bridges 182● Hybrid dentures 209Straumann® Classic 231

PRO

STH

ETIC

S

104

CASSETTES, INSERTS AND STORAGE SYSTEM


040.185 Prosthetic cassettefor instruments andauxiliary components,complete (withoutdividers)


Anodized Al

041.022 Prosthetic cassettefor instruments andauxiliary components


Anodized Al

041.211 Trayfor cassette 041.022


Anodized Al

041.612 Dividerlarge, for dish 041.440

Length 47.5 mm,Width 9.5 mm,Height 1 mm

Anodized Al

041.615 Dividersmall, for dish 041.440

Length 27.5 mm,Width 9.5 mm,Height 1 mm

Anodized Al

041.440 Dishfor tray 041.211


Anodized Al

041.412 Calibration cupyellow

Ø 80 mm Anodized Al

Auxiliary parts

140.055 Plexiglass cassette/Membranette


Plastic

PRO

STH

ETICS

105

CASSETTES, INSERTS AND STORAGE SYSTEM


Storage system

041.501 Storage systemfor prosthetics incl.drawers and dividers


PS

PRO

STH

ETIC

S

106

PROSTHETIC INSTRUMENTS


046.400 SCS Screwdriverfor ratchet, extra short


046.401 SCS Screwdriverfor ratchet, short


046.402 SCS Screwdriverfor ratchet, long


046.085 Screwdriver handlefor 046.410/411/412

Length 109 mm Stainlesssteel/PEEK

046.410 SCS Screwdriverfor handpiece, extra short


046.411 SCS Screwdriverfor handpiece, short


046.412 SCS Screwdriverfor handpiece, long


046.067 Solid abutment driverfor RN Solid abutments6°, short


046.068 Solid abutment driverfor RN Solid abutments6°, long


046.069 Retentive anchor driver Length 19 mm Stainlesssteel

046.415 LOCATOR® Core tool Length 100 mm Stainlesssteel

046.416 LOCATOR® Driverfor ratchet, short


046.417 LOCATOR® Driverfor ratchet, long


PRO

STH

ETICS

107

PROSTHETIC INSTRUMENTS


046.119 Ratchetincludes service instrument


046.108 Service instrumentfor ratchet


046.049 Torque control devicefor ratchet


045.111V4 Cleaning brushfor ratchet


Stainlesssteel/Nylon

046.239 Analog holder Length 105 mm Al/Steel

046.240 Handlefor reamers and tap for TS

Length 65 mm Steel/Brass

046.237 NNC Reamerfor 45° shoulder

Ø 8 mm Carbidemetal

046.243 Reamerfor 45° shoulders


046.246 Guide pinfor reamer 046.243, forsynOcta® 048.605


046.241 synOcta® Guide pinfor reamer 046.243, forsynOcta® 1.5 abutments


046.247 synOcta® Guide pinfor reamer 046.243, forsynOcta® 048.606

Length 50 mm Al/Ti

046.249 NNC Guide pinfor reamer 046.237


The SCS screwdrivers also act as inserting instruments for the WN Solid abutments, for all synOcta® abutments, for allCrossFit® prosthetic components as well as for all closure screws and healing caps in the Straumann® Dental ImplantSystem.

PRO

STH

ETICS

PROSTHETICS

PROSTHETICS FOR STRAUMANN® STANDARD, STANDARD PLUS AND TAPERED EFFECTIMPLANTS

PRO

STH

ETICS

109

PRO

STH

ETIC

S

110

PROSTHETIC PLANNING AIDS


Prosthetic planning kit

048.901 Prosthetic planning kitcontents: 6 x 048.920, 6 x 048.929,6 x 048.921, 6 x 048.916, 6 x 048.923,6 x 048.917, 6 x 048.918, 6 x 048.919,6 x 048.922, 6 x 048.924, 6 x 048.925,6 x 048.930, 6 x 048.931, 6 x 048.932,6 x 048.933, 6 x 048.934, 6 x 048.926,6 x 048.927, 6 x 048.928, 6 x 048.935,6 x 048.936, 6 x 048.937

PC

048.904 Soft Tissue Level PLAN Setcontents: 048.935V4, 048.936V4, 048.937V4,048.275V4, 048.276V4, 048.277V4,048.278V4, 048.279V4, 048.280V4,048.916V4, 048.917V4, 048.918V4,048.919V4, 048.920V4, 048.921V4,048.922V4, 048.923V4, 048.924V4,048.925V4, 048.926V4, 048.927V4,048.928V4, 048.929V4, 048.930V4,048.931V4, 048.932V4, 048.933V4,048.934V4, 048.283V4, 048.284V4,048.285V4, 048.286V4, 048.287V4,048.938V4, 048.939V4

PC

048.905 Soft Tissue Level PLAN Cassetteempty

PC

PLAN abutments

048.920V4 RN synOcta® PLAN abutment POM

048.929V4 RN synOcta® 1.5 PLAN abutment POM

048.921V4 RN synOcta® Transversal PLAN abutment POM

048.916V4 RN synOcta® 15° angled PLAN abutmenttype A, 5.7 mm

POM

048.917V4 RN synOcta® 15° angled PLAN abutmenttype B, 5.7 mm

POM


POM


POM


POM


POM

PRO

STH

ETICS

111



PLAN abutments


POM


POM

048.930V4 RN synOcta® Cementable PLAN abutment POM

048.931V4 WN synOcta® 1.5 PLAN abutment POM

048.932V4 WN synOcta® Cementable PLAN abutment POM

048.933V4 WN synOcta® 15° angled PLAN abutmenttype A

POM

048.934V4 WN synOcta® 15° angled PLAN abutmenttype B

POM

PRO

STH

ETIC

S

112



048.926V4 RN PLAN Solid abutment Height 4 mm POM

048.927V4 RN PLAN Solid abutment Height 5.5 mm POM

048.928V4 RN PLAN Solid abutment Height 7 mm POM

048.275V4 RN PLAN LOCATOR® Abutment

Height 1 mm POM


Height 2 mm POM


Height 3 mm POM


Height 4 mm POM


Height 5 mm POM


Height 6 mm POM

048.938V4 WN PLAN Solid abutment 6° Height 4 mm POM

048.939V4 WN PLAN Solid abutment 6° Height 5.5 mm POM

048.283V4 WN PLAN LOCATOR® Abutment

Height 1 mm POM


Height 2 mm POM


Height 3 mm POM


Height 4 mm POM


Height 5 mm POM

048.935V4 NN PLAN coping Height 9 mm POM

048.936V4 NN angled PLAN coping 15° POM

048.937V4 NN angled PLAN coping 20° POM

ImportantThese prosthetic planning aids can be used in the mouth and are sterilizable up to 20 times.Take care to prevent aspiration in the patient by securing the PLAN abutment with the SCS screwdriver.

* not all materials are available in all countries

Straumann® CARES® CADCAM offers you a range of implant-borne prosthetic solutions in order to achieve high-quality dental implant restorations. Straumann® CARES® Implant-borne elements are designed for high reliability and predictability.

All implant-borne prosthetic solutions can be ordered via Straumann® CARES® Visual software.

Straumann® CARES® AbutmentsFor customized patient solutions For cement-retained crowns and bridges via

mesostructure For screw-retained crowns (ceramic abutments only) Available in two different materials:

titanium and ceramic One-piece abutments

Characteristics Customized shape and emergence profile Control over cement gap Proven Straumann precision fit

Straumann® CARES® Screw-retained bars and bridgesFor complex customized patient solutions For screw-retained bridges For screw-retained Dolder® bars In two different materials: titanium* and cobalt-chromium

alloy (coron®)

Characteristics Direct connection to the implant, no additional

abutment needed High precision Available for Soft Tissue Level

PRO

STH

ETICS

STRAUMANN® CARES® IMPLANT-BORNE ELEMENTSSOFT TISSUE LEVELCUSTOMIZED IMPLANT PROSTHETICS

113

Straumann® CARES® Variobase coping To allow Straumann® dental restorations on competitive

implant systems By maintaining the genuine abutment-implant connection For dental restorations on Camlog® and NobelReplace™

implants Available in zerion™

Characteristics Customized shape and emergence profile Proven Straumann precision fit

Process description 1. For appropriate scanner and software compatibility

please ask your local Straumann sales representative.2. The model situation is scanned with the Straumann®

CARES® Scan CS2 scanner.3. The prosthetic part of the abutment is designed with

Straumann® CARES® Visual.4. The data generated is sent to the Straumann milling cen-

ter via the Straumann® CARES® Visual software or the Straumann® CARES® Webshop (for abutments only – http://cares.straumann.com).

5. The customized abutment is manufactured at the Straumann milling center.

6. Express delivery to the dental laboratory in just a few working days.

All final abutments are permanently screwed into the implant at 35 Ncm.

Straumann® CARES® Implant-borne prosthetics may not be available in your country.For further information please ask your local Straumann sales representative.

PRO

STH

ETIC

S


114

PRO

STH

ETICS

115



Narrow Neck

048.353*048.353-04*

NN Occlusal screw(for ceramic only)

Length 5 mm TAN

049.177* NN Occlusal screwyellow

Length 5 mm,Thread Ø 1.8 mm

TAN

048.087048.087-04

NN Wax-up sleevefor single use

Length 15 mm PEEK

048.067 NN Straumann® Scanbodyincludes fixation screw, forStraumann® CARES® es1scanner and Straumann® CARES® Scan CS2scanner, for softwareversion CARES® Visual6.2 and lower

Length 9.2 mm PEEK/TAN

048.167 NN Straumann® CARES® Mono Scanbodyincludes fixation screw, forStraumann® CARES® ScanCS2 scanner, for softwareversion Straumann® CARES® Visual 6.2 andhigher

Length 9 mm PEEK/TAN

048.084V4 NN Scanbodyfor Sirona® System


ABS

048.132 NN Repositionableimplant analogfor fully digital andconventional workflow


* = For individual ordering only in cases where the screw supplied is lost.

For further information and the webshop, refer to http://cares.straumann.com.

Straumann® CARES® Abutments may not be available in your country.

PRO

STH

ETIC

S

116



Regular Neck

048.354*048.354V4*

RN Occlusal screw(for ceramic only)

Length 5 mm TAN

048.356* synOcta® basal screw Length 6.7 mm TAN

048.088048.088-04

RN Wax-up sleevefor single use

Length 19.3 mm PEEK

048.068 RN Straumann® Scanbodyincludes fixation screw, forStraumann® CARES® es1scanner and Straumann® CARES® Scan CS2scanner, for softwareversion CARES® Visual6.2 and lower

Length 8.5 mm PEEK/Ti

048.168 RN Straumann® CARES® Mono Scanbodyincludes fixation screw, forStraumann® CARES® ScanCS2 scanner, for softwareversion Straumann® CARES® Visual 6.2 andhigher


048.085V4 RN Scanbodyfor Sirona® System


ABS

048.129 RN Repositionable implantanalogfor fully digital andconventional workflow





PRO

STH

ETICS

117



Wide Neck

048.356* synOcta® basal screw Length 6.7 mm TAN

048.089048.089-04

WN Wax-up sleevefor single use

Length 16.4 mm PEEK

048.069 WN Straumann® Scanbodyincludes fixation screw, forStraumann® CARES® es1scanner and Straumann® CARES® Scan CS2scanner, for softwareversion CARES® Visual6.2 and lower

Length 8.9 mm PEEK/Ti

048.169 WN Straumann® CARES® Mono Scanbodyincludes fixation screw, forStraumann® CARES® ScanCS2 scanner, for softwareversion Straumann® CARES® Visual 6.2 andhigher


048.086V4 WN Scanbodyfor Sirona® System


ABS

048.172 WN Repositionableimplant analogfor fully digital andconventional workflow





PRO

STH

ETIC

S

118



Wax-up kits

019.0063 Straumann® CARES® Wax-up kitcontains wax-up sleeveholders for Straumann® dental restorations onStraumann® implants

019.0050 Straumann® CARES® Wax-up kit for Camlog®

contains wax-up sleeveholders for Straumann® dental restorations onCamlog® implants

019.0051 Straumann® CARES® Wax-up kit for NobelReplace™contains wax-up sleeveholders for Straumann® dental restorations onNobelReplace™ implants



PRO

STH

ETICS

119

CROWNS AND BRIDGESNARROW NECK CrossFit® Ø 3.5 mm PROSTHETIC SYSTEMIMPRESSION TAKING AND SOFT TISSUE MANAGEMENT


Impression taking and master cast fabrication

048.128 NNC Impression postfor open tray

Height 10.1 mm TAN

048.134 NNC Impression postfor closed tray

Height 10.9 mm POM/TAN

048.127 NNC Implant analog Length 12.5 mm Ti

Temporary restoration

048.501 NNC Postfor temporary restoration,for crown

Height 10.3 mm TAN

048.502 NNC Postfor temporary restoration,for bridge

Height 10.3 mm TAN

Auxiliary parts

048.313 NNC Basal screw Height 7.1 mm TAN

048.314 NNC Basal screwfor cementable abutment

Height 7.1 mm TAN


ImportantThe temporary abutment is screwed into the implant at 15–35 Ncm.

NNC prosthetic components can only be used with Straumann® Standard Plus Narrow Neck CrossFit® Ø 3.5 mmimplants.


PRO

STH

ETIC

S

120

CROWNS AND BRIDGESNARROW NECK CrossFit® Ø 3.5 mm PROSTHETIC SYSTEMCEMENTABLE ABUTMENT


Cement-retained restorations

048.598 NNC Cementableabutmentstraight, for crown andbridge

Height 5.7 mm Ti

048.621 NNC Cementableabutmentangled 15°, type A

Height 5.9 mm Ti

048.622 NNC Cementableabutmentangled 15°, type B

Height 5.9 mm Ti

Burn-out copings

048.256 NNC Plastic copingfor cementable abutment,straight, for crown

Height 7 mm POM

048.257 NNC Plastic copingfor cementable abutment,straight, for bridge

Height 7 mm POM

048.258 NNC Plastic copingfor cementable abutment,angled 15°, for crownand bridge

Height 7.2 mm POM

Auxiliary parts

048.314 NNC Basal screwfor cementable abutment

Height 7.1 mm TAN


ImportantNNC Cementable abutments are permanently screwed into the implant at 35 Ncm.

NNC prosthetic components can only be used with Straumann® Standard Plus Narrow Neck CrossFit® Ø 3.5 mmimplants.


NNC Cementable angled 15° abutments are for cement-retained crowns and bridgesTwo types of NNC Cementable angled 15° abutments are available, Type A and Type B. This enables the axis to be corrected in 8 different alignments (in 45° graduations).

The NNC Cementable angled 15° abutments: Can undergo height adjustment, but a minimum height of

3 mm above the mucosa margin of the abutment must be maintained to ensure proper stability and retention of the restoration.

Must not be cemented into the implant. Are permanently screwed into the implant at 35 Ncm;

use a new basal screw for the final insertion of the abutment.

Cannot be tightened/loosened with the extra short SCS Screwdriver.

Note1. Not suitable for direct ceramic veneering.2. The cement margin must not be more than 2 mm below

the mucosa.3. NNC components can only be used with Straumann®

Standard Plus Narrow Neck CrossFit® Ø 3.5 mm implants.

NoteNNC products may not be available in all countries, subject to regulatory approval and market release. Please check with your local sales representative for more information.

A = angle between flat sides

B = angle to the flat wall

PRO

STH

ETICS

CROWNS AND BRIDGESNARROW NECK CrossFit® Ø 3.5 mm PROSTHETIC SYSTEMCEMENTABLE ABUTMENT, ANGLED 15°

121

PRO

STH

ETIC

S

122

CROWNS AND BRIDGESNARROW NECK CrossFit® Ø 3.5 mm PROSTHETIC SYSTEMGOLD ABUTMENT


Screw-retained or cement-retained restorations

048.592 NNC Gold abutmentfor crown

Height 3.6 mm Ceramicor®/TAN/POM

048.593 NNC Gold abutmentfor bridge

Height 3.6 mm Ceramicor®/TAN/POM

Auxiliary parts

048.313 NNC Basal screw Height 7.1 mm TAN


Ceramicor® is a non-oxidizing precious metal alloy for casting on precious metal alloys.

The NNC abutments are permanently screwed into the implant at 35 Ncm.


PRO

STH

ETICS

123

CROWNS AND BRIDGESNARROW NECK CrossFit® Ø 3.5 mm PROSTHETIC SYSTEM



048.016 NN Impression capwith integral guide screw

Length 17.5 mm Al/TAN

048.122V4 NN Impression capsnap-on

Length 12 mm POM

048.130 NN Implant analog Length 14 mm Stainlesssteel

048.132 NN Repositionableimplant analogfor fully digital andconventional workflow


Components for temporary restoration

048.050 NN Protective capwith integral occlusalscrew

Height 3.4 mm PEEK/TAN

048.669 NN Temporary copingincludes NN Occlusalscrew

Height 10 mm PEEK/Ti

Screw-retained and cement-retained restorations

048.500 NN Framework blankcan be trimmed, for thedirect applicationof ceramic materials

Height 9 mm,Alloy weight 0.92 g

Esteticor® Cosmor H*

048.635 NN Gold copingcast-on


Ceramicor®/POM

048.505 NN Copingcan be trimmed

Height 9 mm Ti

048.550 NN Coping15° angled

Height 8.8 mm Ti

048.551 NN Coping20° angled

Height 8.8 mm Ti

049.177** NN Occlusal screwyellow

Length 5 mm,Thread Ø 1.8 mm

TAN

* = Esteticor® Cosmor H is a bonding, non -cast-on alloy for direct veneering with ceramic.** = For individual ordering only in cases where the screw supplied is lost.

Ceramicor® is a non-oxidizing precious metal alloy for casting on precious metal alloys.

The NN Copings are permanently screwed onto the implant at 35 Ncm.

PRO

STH

ETIC

S

124

CROWNS AND BRIDGESsynOcta® PROSTHETIC SYSTEM (REGULAR NECK Ø 4.8 mm)IMPRESSION TAKING AND SOFT TISSUE MANAGEMENT



048.017V4 RN Impression cap Height 8 mm POM

048.070V4 RN synOcta® Positioningcylinderred

Height 12 mm POM

048.010 RN synOcta® Impressionpostwith integral guide screw

Height 10 mm Al/Ti

048.090 RN synOcta® Impressionpostwith integral guide screw

Height 25 mm Al/Ti

048.124 RN synOcta® analoggray with red stripe


048.129 RN Repositionable implantanalogfor fully digital andconventional workflow


Bite registration

048.940V4 Bite registration aidshort

Height 8 mm,Ø 5 mm

POM

048.941V4 Bite registration aidlong

Height 12 mm,Ø 5 mm

POM

ImportantRN components can only be used with Straumann® Standard, Standard Plus and Tapered Effect implants with aØ 4.8 mm Regular Neck.

PRO

STH

ETICS

125

CROWNS AND BRIDGESsynOcta® PROSTHETIC SYSTEM (REGULAR NECK Ø 4.8 mm)IMPRESSION TAKING AND SOFT TISSUE MANAGEMENT


048.668 RN synOcta® TemporaryMeso abutmentincludes basal screw*


048.356** synOcta® basal screw Length 6.7 mm TAN

048.650 RN synOcta® Postfor temporary restorationswith integral guide screw,bridge

Height 9 mm Ti

048.651 RN synOcta® Postfor temporary restorationswith integral guide screw,crown

Height 9 mm Ti

049.181 SCS Occlusal screwfor guiding sleeve andpost for temporaryrestoration


* = Available separately under Art. No. 048.356** = For individual ordering only in cases where the screw supplied is lost.


PRO

STH

ETIC

S

126

CROWNS AND BRIDGESsynOcta® PROSTHETIC SYSTEM (REGULAR NECK Ø 4.8 mm)1.5 ABUTMENT


048.601 RN synOcta® 1.5 screw-retained abutment

Height 1.5 mm TAN

Screw-retained restorations

048.632 RN synOcta® Gold copingfor synOcta® 1.5 (includesmodeling aid), bridge

Height 4.25/12 mm,Alloy weight 0.33 g

Ceramicor®/POM

048.633 RN synOcta® Gold copingfor synOcta® 1.5 (includesmodeling aid), crown


Ceramicor®/POM

048.227 RN synOcta® Plasticcopingfor synOcta® 1.5,bridge/bar

Height 10 mm POM

048.229 RN synOcta® Plasticcopingfor synOcta® 1.5, crown

Height 10 mm POM

048.350048.350V4


Auxiliary parts







046.245 Polishing protectorfor RN synOcta® Copings,transocclusal screw-retained



The RN synOcta® 1.5 abutment is permanently screwed into the implant at 35 Ncm.


PRO

STH

ETICS

127




048.571 RN synOcta® Meso millingcylinderfor synOcta® 1.5, crown


Ti

048.350048.350V4


048.642 RN synOcta® Goldabutmentcrown, (includes basalscrew 048.356)

Height 4.3 mm,Alloy weight 0.61 g

Ceramicor®/POM

048.356 synOcta® basal screw Length 6.7 mm TAN

The RN synOcta® 1.5 abutment is permanently screwed into the implant at 35 Ncm.


PRO

STH

ETIC

S

128




Height 1.5 mm TAN

Tapered crowns and bridges of titanium

048.240 RN synOcta® Millingcylinderfor synOcta® 1.5, crown

Height 8 mm,Ø 6 mm

Ti

048.241 RN synOcta® Millingcylinderfor synOcta® 1.5, bridge

Height 8 mm,Ø 6 mm

Ti

048.362V4 SCS Guide screwfor 048.240/241,cannot be shortened

Length 8 mm Ti

048.363V4 SCS Guide screwfor 048.240/241, canbe shortened by 2 mm

Length 8 mm Ti


PRO

STH

ETICS

129

CROWNS AND BRIDGESsynOcta® PROSTHETIC SYSTEM (REGULAR NECK Ø 4.8 mm)CEMENTABLE ABUTMENT


048.605 RN synOcta® Cementableabutment

Height 5.5 mm Ti


048.662 RN synOcta® Plasticcopingfor 048.605, bridge

Height 7 mm POM

048.663 RN synOcta® Plasticcopingfor 048.605, crown

Height 7 mm POM

Auxiliary parts

048.059V4 Transfer aidfor 048.605

Height 6.5 mm PC



046.246 Guide pinfor reamer 046.243, forsynOcta® 048.605





The RN synOcta® cementable abutment is permanently screwed into the implant at 35 Ncm.


PRO

STH

ETIC

S

130

CROWNS AND BRIDGESsynOcta® PROSTHETIC SYSTEM (REGULAR NECK Ø 4.8 mm)15° AND 20° ANGLED ABUTMENT


048.612 RN synOcta® 15° angled abutmentshort, type A

Height 5.7 mm Ti/TAN

048.613 RN synOcta® 15° angled abutmentshort, type B


048.617 RN synOcta® 20° angled abutmentshort, type A


048.618 RN synOcta® 20° angled abutmentshort, type B


048.610 RN synOcta® 15° angled abutmentlong, type A


048.611 RN synOcta® 15° angled abutmentlong, type B


048.615 RN synOcta® 20° angled abutmentlong, type A


048.616 RN synOcta® 20° angled abutmentlong, type B



048.670 Extension shellfor short and long RN synOcta® 15° and 20° angled abutments

Height 5.5 mm POM

048.676V4 Plastic shoulderfor short and long RN synOcta® 15° and 20° angled abutments

Height 4 mm POM

048.350048.350V4


Auxiliary parts

048.000V4 Transfer aidfor RN synOcta® 15° and 20°angled abutments, short

Height 5.5 mm PC

048.002V4 Transfer aidfor RN synOcta® 15° and 20°angled abutments, long

Height 5.5 mm PC


RN synOcta® 15° and 20° angled abutments for screw-retained and cement-retained crowns and bridges

Important Due to their design, angled abutments must not be

trimmed orindividually modified. Abutments must not be cemented into the implant. In the case of the angled abutments, 2 types are

available for each angle. This enables the axis to be corrected in 16 different alignments.

The RN synOcta® angled abutments are permanently screwed into the implant at 35 Ncm.

Angled abutments must not be used with 15° angled hollow cylinder Straumann implants.

Angled abutments cannot be tightened/loosened with the extra short SCS Screwdriver.

ImportantRN components can only be used with Straumann® Standard, Standard Plus and Tapered Effect implants with a Ø 4.8 mm Regular Neck.

A = angle to the edge

B = angle to the surface

PRO

STH

ETICS

CROWNS AND BRIDGESsynOcta® PROSTHETIC SYSTEM (REGULAR NECK Ø 4.8 mm)

131

PRO

STH

ETIC

S

132

CROWNS AND BRIDGESsynOcta® PROSTHETIC SYSTEM (REGULAR NECK Ø 4.8 mm)TRANSVERSAL (TS) ABUTMENT


048.620 RN synOcta® Transversal(TS) screw-retainedabutment

Height 4 mm Ti


048.634 RN synOcta® TS goldcoping


Ceramicor®

048.665 RN synOcta® TS plasticcoping


Ceramicor®/POM

048.672 RN synOcta® TS threadprotection screwfor 048.634 and048.665

Length 8.2 mm,Ø 3 mm

Stainlesssteel

049.154 Transversal screwfor 048.620

Length 3 mm,Ø 2 mm

TAV

Auxiliary parts

046.420 TS Hexagonal screwdriver Length 24 mm Stainlesssteel

048.003V4 Transfer aidfor RN synOcta® TSabutment

Height 5 mm PC



044.570 Tapfor TS

M2 x 0.25 mm Stainlesssteel


The RN synOcta® TS abutment is permanently screwed into the implant at 35 Ncm. The transversal screw is tightenedonly by hand.


PRO

STH

ETICS

133

CROWNS AND BRIDGESsynOcta® PROSTHETIC SYSTEM (WIDE NECK Ø 6.5 mm)IMPRESSION TAKING AND SOFT TISSUE MANAGEMENT



048.013 WN Impression cap Height 8 mm POM

048.095 WN synOcta® positioningcylinderwhite

Height 12 mm POM

048.091 WN synOcta® impression capwith integral guide screw

Height 10 mm Al

048.171 WN synOcta® analoggray


048.172 WN Repositionable implantanalogfor fully digital andconventional workflow


Bite registration

048.940V4 Bite registration aidshort

Height 8 mm,Ø 5 mm

POM

048.941V4 Bite registration aidlong


POM


048.233 WN synOcta® Postfor temporary restorations withintegral guide screw, crown

Height 9 mm Ti

048.234 WN synOcta® Postfor temporary restorations withintegral guide screw, bridge

Height 9 mm Ti

049.181 SCS Occlusal screwfor guiding sleeve and post fortemporary restoration


ImportantWN components can only be used with Straumann® Standard, Standard Plus and Tapered Effect implants with aØ 6.5 mm Wide Neck.

PRO

STH

ETIC

S

134

CROWNS AND BRIDGESsynOcta® PROSTHETIC SYSTEM (WIDE NECK Ø 6.5 mm)1.5 ABUTMENT


048.603 WN synOcta® 1.5 screw-retained abutment

Height 1.5 mm Ti


048.638 WN synOcta® Goldcopingfor synOcta® 1.5 (includesmodeling aid), bridge


Ceramicor®/POM

048.639 WN synOcta® Goldcopingfor synOcta® 1.5 (includesmodeling aid), crown


Ceramicor®/POM

048.666 WN synOcta® Plasticcopingbridge

Height 10 mm POM

048.667 WN synOcta® Plasticcopingcrown

Height 10 mm POM

048.350048.350V4



048.644 WN synOcta® Goldabutmentcrown, (includes basalscrew 048.356)


Ceramicor®/POM

048.573 WN synOcta® Mesomilling cylinderfor synOcta® 1.5, crown


Ti

048.350048.350V4


The WN synOcta® 1.5 abutment is permanently screwed into the implant at 35 Ncm.


PRO

STH

ETICS

135

CROWNS AND BRIDGESsynOcta® PROSTHETIC SYSTEM (WIDE NECK Ø 6.5 mm)1.5 ABUTMENT


Auxiliary parts








The WN synOcta® 1.5 abutment is permanently screwed into the implant at 35 Ncm.


PRO

STH

ETIC

S

136

CROWNS AND BRIDGESsynOcta® PROSTHETIC SYSTEM (WIDE NECK Ø 6.5 mm)CEMENTABLE ABUTMENT


048.606 WN synOcta® cementable abutment

Height 5.5 mm Ti


048.243 WN synOcta® Plasticcopingfor 048.606, crown

Height 7.35 mm POM

048.244 WN synOcta® Plasticcopingfor 048.606, bridge

Height 7.35 mm POM

Auxiliary parts

048.054V4 Transfer aidfor 048.606

Height 6.5 mm PC



046.247 synOcta® Guide pinfor reamer 046.243, forsynOcta® 048.606

Length 50 mm Al/Ti




The WN synOcta® cementable abutment is permanently screwed into the implant at 35 Ncm.


PRO

STH

ETICS

137

CROWNS AND BRIDGESsynOcta® PROSTHETIC SYSTEM (WIDE NECK Ø 6.5 mm)15° ANGLED ABUTMENT


048.608 WN synOcta® 15° angledabutmenttype A


048.609 WN synOcta® 15° angledabutmenttype B



048.678 Plastic shoulderfor WN synOcta® 15° angledabutments

Height 4 mm POM

Auxiliary parts

048.032 Transfer aidfor WN synOcta® 15° angledabutments

Height 5 mm PC

Important Abutments must not be cemented into the implant. Two types of angled WN abutments are available.

This allows correction of the axis in 16 different directions. Angled abutments cannot be tightened/loosened with

the extra short SCS Screwdriver. The WN synOcta® angled abutments are screwed defini-

tively into the implant at 35 Ncm.

ImportantWN components can only be used with Straumann® Standard, Standard Plus and Tapered Effect implants with a Ø 6.5 mm Wide Neck.

A = angle to the edge

B = angle to the surface

PRO

STH

ETIC

S

CROWNS AND BRIDGESsynOcta® PROSTHETIC SYSTEM (WIDE NECK Ø 6.5 mm)

138

PRO

STH

ETICS

139

CROWNS AND BRIDGESSOLID ABUTMENT PROSTHETIC SYSTEM (NARROW NECK CrossFit® Ø 3.5 mm)


048.547 NNC Solid abutmentyellow

Height 4 mm Ti

048.548 NNC Solid abutmentgray

Height 5.5 mm Ti

048.549 NNC Solid abutmentblue

Height 7 mm Ti

Auxiliary parts

048.155 NNC Solid abutmentdrivershort


048.156 NNC Solid abutmentdriverlong


NNC Solid abutments are permanently screwed into the implant at 35 Ncm and must not be removed after theimpression has been taken.

ImportantNNC components can only be used with Straumann® Standard Plus Narrow Neck CrossFit® Ø 3.5 mm implants.


PRO

STH

ETIC

S

140




048.579 NNC Impression cap Height 8 mm POM

048.587 NNC Positioning cylinderfor 048.547, yellow

Height 10.2 mm POM

048.588 NNC Positioning cylinderfor 048.548, gray

Height 10.2 mm POM

048.589 NNC Positioning cylinderfor 048.549, blue

Height 10.2 mm POM

048.527 NNC Analogfor Solid abutment for048.547, yellow

Height 14.3 mm TAN

048.528 NNC Analogfor Solid abutment for048.548, gray

Height 15.8 mm TAN

048.529 NNC Analogfor Solid abutment for048.549, blue

Height 17.3 mm TAN



PRO

STH

ETICS

141




048.658 NNC Temporary copingfor Solid abutment, crown

Height 8.5 mm PMMA

048.659 NNC Temporary copingfor Solid abutment, bridge

Height 8.5 mm PMMA

048.700 NNC Protective capfor Solid abutment, for048.547

Height 5.6 mm PEEK


Height 7.1 mm PEEK


Height 8.6 mm PEEK



PRO

STH

ETIC

S

142



Components for cement-retained crowns and bridges

048.263 NNC Plastic copingfor Solid abutment, crown

Height 10.2 mm POM

048.264 NNC Plastic copingfor Solid abutment, bridge

Height 10.2 mm POM

Auxiliary parts

046.237 NNC Reamerfor 45° shoulder


046.249 NNC Guide pinfor reamer 046.237







PRO

STH

ETICS

143

CROWNS AND BRIDGESSOLID ABUTMENT PROSTHETIC SYSTEM (REGULAR NECK Ø 4.8 mm)


All-in-One Sets

040.740 RN Solid All-in-One Setfor crown

Height 4 mm


Height 5.5 mm


Height 7 mm

040.840 RN Solid All-in-One Setfor bridge

Height 4 mm


Height 5.5 mm


Height 7 mm

048.540 RN Solid abutment 6°yellow

Height 4 mm Ti

048.541 RN Solid abutment 6°gray

Height 5.5 mm Ti

048.542 RN Solid abutment 6°blue

Height 7 mm Ti

Auxiliary parts

046.067 Solid abutment driverfor RN Solid abutments 6°,short


046.068 Solid abutment driverfor RN Solid abutments 6°,long


RN Solid abutments are permanently screwed into the implant at 35 Ncm and must not be removed after theimpression has been taken.


PRO

STH

ETIC

S

144




048.017V4 RN Impression cap Height 8 mm POM

048.060V4 Positioning cylinderfor 048.540, yellow

Height 10.2 mm POM

048.061V4 Positioning cylinderfor 048.541, gray

Height 10.2 mm POM

048.062V4 Positioning cylinderfor 048.542, blue

Height 10.2 mm POM

048.160 Analogfor 048.540, yellow

Length 14.3 mm Al

048.161 Analogfor 048.541, gray

Length 15.8 mm Al

048.162 Analogfor 048.542, blue

Length 17.3 mm Al

048.117V4 Shoulder analogfor RN Solid abutments, withreinforcement pin

Length 10 mm,Length 17 mm

PPS/Brass


048.654 RN Temporary copingfor RN Solid abutments,bridge

Height 8.5 mm PMMA

048.655 RN Temporary copingfor RN Solid abutments, crown

Height 8.5 mm PMMA

048.047V4 RN Protective capfor 048.540, cementable

Height 5.8 mm PEEK


Height 7.3 mm PEEK


Height 8.8 mm PEEK


PRO

STH

ETICS

145




048.245 Plastic copingfor RN Solid abutments, crown

Height 10 mm POM

048.246 Plastic copingfor RN Solid abutments,bridge

Height 10 mm POM

Auxiliary parts



046.242 Guide pinfor reamer 046.243, for RNSolid abutments






PRO

STH

ETIC

S

146

CROWNS AND BRIDGESSOLID ABUTMENT PROSTHETIC SYSTEM (WIDE NECK Ø 6.5 mm)


All-in-One Sets

040.845 WN Solid All-in-One Setfor bridge

Height 4 mm

040.846 WN Solid All-in-One Setfor bridge

Height 5.5 mm

040.745 WN Solid All-in-One Setfor crown

Height 4 mm

040.746 WN Solid All-in-One Setfor crown

Height 5.5 mm

048.545 WN Solid abutment 6°green

Height 4 mm Ti

048.546 WN Solid abutment 6°brown

Height 5.5 mm Ti


048.013 WN Impression cap Height 8 mm POM

048.065 Positioning cylinderfor 048.545, green

Height 10 mm POM

048.066 Positioning cylinderfor 048.546, brown

Height 10 mm POM

048.165 Analogfor 048.545, green

Length 16 mm Al

048.166 Analogfor 048.546, brown

Length 17.5 mm Al

048.140 Shoulder analogfor WN Solid abutments

Length 10 mm Al

The WN Solid abutments are screwed into the implant with an SCS Screwdriver (see page 95) prior to impressiontaking, and tightened definitively at 35 Ncm. They must not be removed from the implant after the impression hasbeen taken.


PRO

STH

ETICS

147




048.656 WN Temporary copingfor WN Solid abutments,bridge

Height 7.3 mm PMMA

048.657 WN Temporary copingfor WN Solid abutments,crown

Height 7.3 mm PMMA

048.051 WN Protective capfor 048.545

Height 6 mm PEEK

048.052 WN Protective capfor 048.546

Height 7.5 mm PEEK

The WN Solid abutments are screwed into the implant with an SCS Screwdriver (see page 95) prior to impressiontaking, and tightened definitively at 35 Ncm. They must not be removed from the implant after the impression hasbeen taken.


PRO

STH

ETIC

S

148




048.247 Plastic copingfor WN Solid abutments,crown

Height 7 mm POM

048.248 Plastic copingfor WN Solid abutments,bridge

Height 7 mm POM

Auxiliary parts



046.244 Guide pinfor reamer 046.243, for WNSolid abutments






PRO

STH

ETICS

PROSTHETICS

HYBRID DENTURES

PRO

STH

ETICS

149

PRO

STH

ETIC

S

150

HYBRID DENTURES (REGULAR NECK Ø 4.8 mm)BAR



Height 1.5 mm TAN

Components for gold bars

048.204 RN synOcta® Gold copingfor synOcta® 1.5, bar


Ceramicor®

048.411 Dolder® baregg-shaped cross-section, mini

Length 25 mm,Height 2.3 mm

Elitor®

048.412 Dolder® baregg-shaped cross-section,regular

Length 25 mm,Height 3 mm

Elitor®

048.413 Dolder® bar matrixincludes spacer, mini


Elitor®/Brass

048.414 Dolder® bar matrixincludes spacer, regular


Elitor®/Brass

048.350048.350V4


040.195 Bar set goldincludes:2 x RN synOcta® 1.5abutment, 048.6012 x RN synOcta® analog,048.1242 x RN synOcta® goldcoping, bar, 048.2044 x SCS Occlusal screw,048.350

For matching guide screws see page 169.


PRO

STH

ETICS

151



Auxiliary parts

048.208V4 Stabilization pin for retaininggold copings in solderinvestment


046.150 Activator setfor all bar matrices, three-part


046.151 Deactivatorfor Dolder® bar matrices, mini

Length 66 mm Grilon BS/Brass

046.152 Deactivatorfor Dolder® bar matrices,regular




PRO

STH

ETIC

S

152




Height 1.5 mm TAN

Components for titanium bars, prefabricated titanium parts for laser welding

048.214 RN synOcta® Titanium copingfor synOcta® 1.5, bar

Height 6 mm Ti

048.466 Titanium baregg-shaped cross-section, mini


Ti

048.465 Titanium baregg-shaped cross-section,regular


Ti

048.471 Titanium bar matrixincludes spacer, mini


Ti/Brass

048.470 Titanium bar matrixincludes spacer, regular


Ti/Brass

048.350048.350V4


040.196 Bar set titaniumincludes:2 x RN synOcta® 1.5abutment, 048.6012 x RN synOcta® analog,048.1242 x RN synOcta® titaniumcoping, bar, 048.2142 x SCS Occlusal screw,048.350



PRO

STH

ETICS

153



Plastic components for one-piece casting method for bars

048.227 RN synOcta® Plastic copingfor synOcta® 1.5, bridge/bar

Height 10 mm POM

048.461 Plastic baregg-shaped cross-section, mini


PMMA

048.460 Plastic baregg-shaped cross-section,regular


PMMA



Ti/Brass



Ti/Brass

048.350048.350V4


040.197 Bar set plasticincludes:2 x RN synOcta® 1.5abutment, 048.6012 x RN synOcta® analog,048.1242 x RN synOcta® plasticcoping, bar, 048.227 2 x SCS Occlusal screw,048.350



PRO

STH

ETIC

S

154



Auxiliary parts

046.245 Polishing protectorfor RN synOcta® Copings,transocclusal screw-retained


048.108 RN synOcta® Analogfor bars with 048.601, one-part


048.093V4 RN synOcta® Impression capfor bars with 048.601, one-part,gray

Height 5 mm POM

048.073V4 Fixation pinfor bars with 048.601, gray

Length 5 mm POM



PRO

STH

ETICS

155

HYBRID DENTURES (REGULAR NECK Ø 4.8 mm)RETENTIVE ANCHOR


048.439 Retentive anchor abutment Height 3.4 mm Ti

046.069 Retentive anchor driver Length 19 mm Stainlesssteel

048.109 Transfer pinfor retentive anchor


Elliptical matrix

048.456 Elliptical matrixincludes lamella retentioninsert


Elitor®/Ti

048.457 Spare lamella retentioninsert

Height 2.6 mm Elitor®

046.154 Screwdriver Length 37 mm Stainlesssteel

Titanium matrix with defined retention force

048.450 Titanium matrixfor retentive anchor

Height 3.1 mm Ti alloy

048.451V4 Spacerfor titanium matrix

Height 3.5 mm POM

048.452 Screwdriverfor titanium matrix


048.453 Extractorfor titanium matrix


048.454V4 Threaded mounting ringfor titanium matrix

Height 2.2 mm POM

048.455V4 Springfor 048.450

Stainlesssteel


PRO

STH

ETIC

S

156

HYBRID DENTURES (REGULAR NECK Ø 4.8 mm)STECO® TITANMAGNETICS®


048.511 Titanmagnetics® insert(abutment)


Ti housing

046.146 Titanmagnetics® Insertapplicator (driver)for ratchet

Length 18 mm Ti housing

048.014 Titanmagnetics® impression coping

Height 7 mm Ti housing

048.121 Titanmagnetics® modelimplant

Length 9 mm Ti housing

048.516 Positioning cuff Height 0.3 mm,Ø 15 mm

Dentalsilicone

048.515 Titanmagnetics® denturemagnet


Ti housing


The Titanmagnetics® insert is screwed into the implant at 15–20 Ncm.

0197Manufacturersteco®-system-technik GmbH & Co. KG

Kollaustrasse 6D-22529 HamburgGermany

PRO

STH

ETICS

157

HYBRID DENTURES (NARROW NECK CrossFit® Ø 3.5 mm)LOCATOR®


LOCATOR® abutments

048.581 NNC LOCATOR® Abutment

Height 1 mm TAV


Height 2 mm TAV


Height 3 mm TAV


Height 4 mm TAV


Height 5 mm TAV


Height 6 mm TAV



0473ManufacturerZest Anchors, Inc.

Escondido, CA 92029USA

PRO

STH

ETIC

S

158



LOCATOR® components

048.189V2 LOCATOR® Male processingpackagecontents:denture cap (Ø 5.5 mm,height 2.5 mm) with blackprocessing male (height 1.9 mm),block-out spacer (048.196),clear replacement male (048.190),pink replacement male (048.191),blue replacement male (048.192)

Ti/Nylon

048.190V4 LOCATOR® Replacement maleclear, 0°–10°•, 5 lbs, 2.27 kg••

Height 1.7 mm Nylon

048.191V4 LOCATOR® Replacement malepink, light retention, 0°–10°•,3 lbs, 1.36 kg••

Height 1.7 mm Nylon

048.192V4 LOCATOR® Replacement maleblue, extra-light retention, 0°–10°•,1.5 lbs, 0.68 kg••

Height 1.7 mm Nylon

• = For the correction of angle divergences•• = Retention force




PRO

STH

ETICS

159




048.182V2 LOCATOR® Male processingpackageextended range, contents:denture cap (Ø 5.5 mm,height 2.5 mm) with blackprocessing male (height 1.9 mm),block-out spacer (048.196),green replacement male(048.193),orange replacement male(048.188),red replacement male (048.194)

Ti/Nylon

048.193V4 LOCATOR® Replacement malegreen, extended range, 10°–20°•,3–4 lbs, 1.36–1.82 kg••

Height 1.7 mm Nylon

048.188V4 LOCATOR® Replacement maleorange, light retention, extendedrange, 10°–20°•, 2 lbs,0.91 kg••

Height 1.7 mm Nylon

048.194V4 LOCATOR® Replacement malered, extra-light retention, extendedrange, 10°–20°•, 0.5–1.5 lbs,0.23–0.68 kg••

Height 1.7 mm Nylon

048.181V4 LOCATOR® Replacement malegray, zero (0) retention

Height 1.7 mm Nylon





PRO

STH

ETIC

S

160




048.198V4 LOCATOR® Femaleanalog


Al

048.197V4 LOCATOR® Impressioncoping

Height 4 mm Al housingwith LDPEinsert

048.196V20 LOCATOR® Block-outspacer

Thickness 0.4 mm Siliconerubber

048.195V4 LOCATOR® Blackprocessing male

Height 1.9 mm LDPE

048.218V4 LOCATOR® Processingspacer

POM

046.413V4 LOCATOR® Abutmentholder sleeve

PSU

Auxiliary parts






048.199V4 LOCATOR® Parallel post Length 8 mm LDPE

048.200 LOCATOR® Anglemeasurement guide


Stainlesssteel




PRO

STH

ETICS

161

HYBRID DENTURES (REGULAR NECK Ø 4.8 mm)LOCATOR®


LOCATOR® abutments

048.175 RN LOCATOR® Abutment Height 1 mm TAV









PRO

STH

ETIC

S

162





Ti/Nylon


Height 1.7 mm Nylon


Height 1.7 mm Nylon


Height 1.7 mm Nylon





PRO

STH

ETICS

163





Ti/Nylon


Height 1.7 mm Nylon


Height 1.7 mm Nylon


Height 1.7 mm Nylon


Height 1.7 mm Nylon





PRO

STH

ETIC

S

164






Al






Height 1.9 mm LDPE


POM


PSU

Auxiliary parts









Stainlesssteel




PRO

STH

ETICS

165

HYBRID DENTURES (WIDE NECK Ø 6.5 mm)LOCATOR®


LOCATOR® abutments

048.183 WN LOCATOR® Abutment Height 1 mm TAV








PRO

STH

ETIC

S

166





Ti/Nylon


Height 1.7 mm Nylon


Height 1.7 mm Nylon


Height 1.7 mm Nylon





PRO

STH

ETICS

167





Ti/Nylon


Height 1.7 mm Nylon


Height 1.7 mm Nylon


Height 1.7 mm Nylon


Height 1.7 mm Nylon





PRO

STH

ETIC

S

168






Al






Height 1.9 mm LDPE


POM


PSU

Auxiliary parts









Stainlesssteel




PRO

STH

ETICS

169

AUXILIARY PARTS


SCS occlusal and guide screws

048.350048.350V4


048.360V4 SCS Guide screwfor RN synOcta® bar copings,cannot be shortened

Length 6 mm Ti

048.361V4 SCS Guide screwfor RN synOcta® bar copings,can be shortened by 1.6 mm

Length 6 mm Ti

048.362V4 SCS Guide screwfor 048.240/241, cannot beshortened

Length 8 mm Ti

048.363V4 SCS Guide screwfor 048.240/241, can beshortened by 2 mm

Length 8 mm Ti

048.364V4 SCS Guide screwcan be shortened by 2 mm

Length 10 mm Ti


Length 12 mm Ti


Length 14 mm Ti

PRO

STH

ETICS

PROSTHETICS

PROSTHETICS FOR STRAUMANN® BONE LEVEL IMPLANTS

PRO

STH

ETICS

171

PRO

STH

ETIC

S

172



PLAN set

026.0101 CrossFit® PLAN set* Length 278 mm,Width 124 mm,Height 33 mm

PC/POM

026.0102 CrossFit® PLAN cassetteempty


PC

PLAN abutments

025.2601-04 NC PLAN Anatomic abutmentstraight

Gingiva height 2 mm POM

025.2602-04 NC PLAN Anatomic abutmentstraight

Gingiva height3.5 mm

POM

025.2603-04 NC PLAN Anatomic abutmentangled 15°


025.2604-04 NC PLAN Anatomic abutmentangled 15°


POM

025.4601-04 RC PLAN Anatomic abutmentstraight


025.4602-04 RC PLAN Anatomic abutmentstraight


POM

025.4603-04 RC PLAN Anatomic abutmentangled 15°


025.4604-04 RC PLAN Anatomic abutmentangled 15°


POM

025.2610-04 NC PLAN Gold abutmentfor crown

Height 3.2 mm POM

025.4610-04 RC PLAN Gold abutmentfor crown

Height 3.3 mm POM

025.4630-04 RC PLAN Gold abutmentfor bridge

Height 5.2 mm POM

* = Contains all PLAN abutments

ImportantPLAN abutments must be cleaned and sterilized with moist heat at 134 °C (273 °F) for 18 min after intraoral use.

PRO

STH

ETICS

173



PLAN abutments

025.2611-04 NC PLANCementable abutment

Ø 3.5 mm,Gingiva height 1 mm,Abutment height 4 mm

POM



POM



POM


Ø 3.5 mm,Gingiva height 1 mm,Abutment height 5.5 mm

POM



POM



POM


Ø 5 mm,Gingiva height 1 mm,Abutment height 4 mm

POM



POM



POM


Ø 5 mm,Gingiva height 1 mm,Abutment height 5.5 mm

POM



POM



POM


PRO

STH

ETIC

S

174



PLAN abutments

025.4621-04 RC PLAN Cementableabutment


POM



POM



POM



POM



POM



POM



POM



POM



POM



POM



POM



POM


PRO

STH

ETICS

175



PLAN abutments

025.2651-04 NC PLAN Multi-baseabutmentstraight

Ø 3.5 mm,Gingiva height 1 mm

POM


Ø 3.5 mm,Gingiva height 2.5 mm

POM



POM



POM



POM



POM

025.2662-04 NC PLAN Multi-baseabutmentangled 25°, type A

Ø 4 mm,Gingiva height 2.5 mm

POM

025.2665-04 NC PLAN Multi-baseabutmentangled 25°, type B


POM


PRO

STH

ETIC

S

176



PLAN abutments

025.4651-04 RC PLAN Multi-base abutmentstraight


POM



POM



POM



POM



POM



POM

025.4662-04 RC PLAN Multi-base abutmentangled 25°, type A


POM

025.4665-04 RC PLAN Multi-base abutmentangled 25°, type B


POM


PRO

STH

ETICS

177



PLAN abutments

025.2642-04 NC PLAN LOCATOR® Abutment Height 2 mm POM





025.4641-04 RC PLAN LOCATOR® Abutment Height 1 mm POM







Straumann® CARES® CADCAM offers you a range of implant-borne prosthetic solutions in order to achieve high-quality dental implant restorations. Straumann® CARES® Implant-borne elements are designed for high reliability and predictability.

All implant-borne prosthetics solutions can be ordered via the Straumann® CARES® Visual software.

Straumann® CARES® AbutmentsFor customized patient solutions For cement-retained crowns and bridges via

mesostructure For screw-retained crowns (ceramic abutments only) Available in two different materials:

titanium and ceramic One-piece abutments

Characteristics Customized shape and emergence profile Control over cement gap Proven Straumann precision fit

Straumann® CARES® Variobase coping To allow Straumann® dental restorations on competitive

implant syxstems. By maintaining the genuine abutment-implant connection. For dental restorations on Camlog® and NobelReplace™

implants Available in zerion™

Characteristics Customized shape and emergence profile Proven Straumann precision fit

PRO

STH

ETIC

S

STRAUMANN® CARES® IMPLANT-BORNE ELEMENTSBONE LEVELCUSTOMIZED IMPLANT PROSTHETICS

178


Straumann® CARES® Implant-borne prosthetics may not be available in your country.For further information please ask your local Straumann sales representative.

Process description 1. For appropriate scanner and software compatibility

please ask your local Straumann sales representative.2. The model situation is scanned with the Straumann®

CARES® Scan CS2 scanner.3. The prosthetic part of the abutment is designed with

Straumann® CARES® Visual.4. The data generated is sent to the Straumann milling

center via the Straumann® CARES® Visual software or the Straumann® CARES® Webshop (for abutments only – http://cares.straumann.com).

5. The customized abutment is manufactured at the Straumann milling center.

6. Express delivery to the dental laboratory in just a few working days.

PRO

STH

ETICS


179

PRO

STH

ETIC

S

180



Narrow CrossFit®

025.2900 NC Basal screw Length 7.9 mm TAN

025.2906 NC Basal screwfor ceramic abutment only

Length 8.9 mm TAN

025.2903025.2903-04

NC Wax-up sleevefor single use

Length 15.2 mm PEEK

025.2905 NC Straumann® Scanbodyincludes fixation screw, forStraumann® CARES® es1scanner and Straumann® CARES® Scan CS2 scanner,for software version CARES® Visual 6.2 and lower


025.2915 NC Straumann® CARES® Mono Scanbodyincludes fixation screw, forStraumann® CARES® ScanCS2 scanner, for softwareversion Straumann® CARES® Visual 6.2 and higher


025.2901-04 NC Scanbodyfor Sirona® System

Length 13.3 mm PEEK/ABS

025.2102 NC Repositionable implantanalogfor fully digital andconventional workflow

Length 17 mm Ti

Regular CrossFit®

025.4900 RC Basal screw Length 7.9 mm TAN

025.4906 RC Basal screwfor ceramic abutment only

Length 8.2 mm TAN

025.4903025.4903-04

RC Wax-up sleevefor single use

Length 18.8 mm PEEK




PRO

STH

ETICS

181



Regular CrossFit®

025.4905 RC Straumann® Scanbodyincludes fixation screw, forStraumann® CARES® es1scanner and Straumann® CARES® Scan CS2 scanner,for software version CARES® Visual 6.2 and lower


025.4915 RC Straumann® CARES® Mono Scanbodyincludes fixation screw, forStraumann® CARES® ScanCS2 scanner, for softwareversion Straumann® CARES® Visual 6.2 and higher


025.4901-04 RC Scanbodyfor Sirona® System

Length 13.3 mm PEEK/ABS

025.4102 RC Repositionable implantanalogfor fully digital andconventional workflow

Length 17 mm Ti

Wax-up kits

019.0063 Straumann® CARES® Wax-upkitcontains wax-up sleeveholders for Straumann® dentalrestorations on Straumann® implants

019.0050 Straumann® CARES® Wax-upkit for Camlog®

contains wax-up sleeveholders for Straumann® dentalrestorations on Camlog® implants

019.0051 Straumann® CARES® Wax-upkit for NobelReplace™contains wax-up sleeveholders for Straumann® dentalrestorations onNobelReplace™ implants




PRO

STH

ETIC

S

182

CROWNS AND BRIDGESNARROW CrossFit®IMPRESSION TAKING AND SOFT TISSUE MANAGEMENT



025.2201 NC Impression postfor closed tray, with1 guide screw and 2 caps

Length 12.3 mm TAN/POM

025.2202 NC Impression postfor open tray, short, withguide screw

Length 16.5 mm TAN

025.2205 NC Impression postfor open tray, long, withguide screw

Length 24 mm TAN

025.2101 NC Implant analog Length 12 mm Ti

025.2102 NC Repositionableimplant analogfor fully digital andconventional workflow

Length 17 mm Ti

Bite registration

025.2208-04 NC Bite registration aid Height 8 mm POM

025.2212-04 NC Bite registration aid Height 12 mm POM


024.2370 NC Temporary abutment Height 12 mm,Ø 5 mm

PEEK/TAN

024.2371 NC Temporary abutmentfor crown


TAN

024.2375 NC Temporary abutmentfor bridge


TAN


ImportantNC prosthetic components can only be used with Straumann® Bone Level implants, Ø 3.3 mm, Narrow CrossFit®.

PRO

STH

ETICS

183

CROWNS AND BRIDGESNARROW CrossFit®IMPRESSION TAKING AND SOFT TISSUE MANAGEMENT


Auxiliary parts





PRO

STH

ETIC

S

184

CROWNS AND BRIDGESNARROW CrossFit®ANATOMIC IPS e.max®, GOLD, ANATOMIC AND MESO ABUTMENT



022.2410 NC Gold abutmentfor crown

Height 3.7 mm Ceramicor®/POM

022.2812 NC Straumann® AnatomicIPS e.max® abutmentstraight

Gingiva height 2 mm ZrO2/MO 0



ZrO2/MO 0

022.2822 NC Straumann® AnatomicIPS e.max® abutmentangled 15°




ZrO2/MO 0





ZrO2/MO 1





ZrO2/MO 1



PRO

STH

ETICS

185

CROWNS AND BRIDGESNARROW CrossFit®ANATOMIC IPS e.max®, GOLD, ANATOMIC AND MESO ABUTMENT



022.2102 NC Anatomic abutmentstraight

Gingiva height 2 mm Ti

022.2104 NC Anatomic abutmentstraight


Ti

022.2152 NC Anatomic abutmentangled 15°


022.2154 NC Anatomic abutmentangled 15°


Ti

022.2202 NC Meso abutment Height 13.4 mm,Ø 6 mm

Ti

Auxiliary parts


025.2920025.2920-04

NC Polishing aid Length 16 mm Stainlesssteel




PRO

STH

ETIC

S

186

CROWNS AND BRIDGESNARROW CrossFit®CEMENTABLE ABUTMENT


All-in-One Sets

027.4301 NC CementableAll-in-One Setfor crown

Ø 3.5 mm,Abutment height 4 mm,Gingiva height 1 mm






Ø 5 mm,Abutment height 4 mm,Gingiva height 1 mm






Ø 5 mm,Abutment height 5.5 mm,Gingiva height 1 mm







PRO

STH

ETICS

187




022.2311 NC Cementable abutment Ø 3.5 mm,Gingiva height 1 mm,Abutment height 4 mm

Ti


Ti


Ti

022.2315 NC Cementable abutment Ø 3.5 mm,Gingiva height 1 mm,Abutment height 5.5 mm

Ti


Ti


Ti



PRO

STH

ETIC

S

188



022.2321 NC Cementable abutment Ø 5 mm,Gingiva height 1 mm,Abutment height 4 mm

Ti


Ti


Ti

022.2325 NC Cementable abutment Ø 5 mm,Gingiva height 1 mm,Abutment height 5.5 mm

Ti


Ti


Ti



PRO

STH

ETICS

189



Impression taking (abutment level) and master cast fabrication, for cementable abutment

025.2203-04 NC Impression capfor cementable abutment

Ø 3.5 mm,Abutment height4 mm

POM


Ø 5 mm,Abutment height4 mm

POM


Ø 5 mm,Abutment height5.5 mm

POM

025.2112 NC Implant analogfor cementable abutment


TAN


Ø 3.5 mm,Abutment height5.5 mm

TAN



TAN



TAN


PRO

STH

ETIC

S

190



Temporary restoration, for cementable abutment

024.2346 NC Temporary copingfor cementable abutment

Ø 3.5 mm PMMA

024.2356 NC Temporary copingfor cementable abutment

Ø 5 mm PMMA

024.2312-04 NC Protective capfor cementable abutment


PEEK



PEEK



PEEK



PEEK


PRO

STH

ETICS

191



Coping, for cementable abutment

023.2310 NC Copingfor bridge on cementableabutment

Ø 3.5 mm POM

023.2316 NC Copingfor crown on cementableabutment

Ø 3.5 mm POM

023.2320 NC Copingfor bridge on cementableabutment

Ø 5 mm POM

023.2326 NC Copingfor crown on cementableabutment

Ø 5 mm POM

Auxiliary parts

025.2911-04 NC Transfer aidfor cementable abutment

Ø 3.5 mm PC

025.2912-04 NC Transfer aidfor cementable abutment

Ø 5 mm PC

025.2908 NC Basal screwfor cementable abutment only

Length 7.9 mm TAN



PRO

STH

ETIC

S

192

BRIDGESNARROW CrossFit®MULTI-BASE ABUTMENT



022.2731 NC Multi-base abutmentstraight


TAN


Ø 3.5 mm,Gingiva height2.5 mm

TAN



TAN



TAN



TAN



TAN

022.2782 NC Multi-base abutmentangled 25°, type A

Ø 4 mm,Gingiva height2.5 mm

TAN

022.2786 NC Multi-base abutmentangled 25°, type B


TAN



PRO

STH

ETICS

193



Impression taking (abutment level) and master cast fabrication, for Multi-base abutment

025.2231-04 NC Impression capfor Multi-base abutment,straight

Ø 3.5 mm POM

025.2241-04 NC Impression capfor Multi-base abutment,straight

Ø 4.5 mm POM

025.2232 NC Impression postfor Multi-base abutment,straight

Ø 3.5 mm TAN

025.2242 NC Impression postfor Multi-base abutment,straight

Ø 4.5 mm TAN

025.2206 NC Impression postfor Multi-base abutment,angled 25°

Ø 4 mm TAN

025.2131 NC Implant analogfor Multi-base abutment,straight

Ø 3.5 mm TAN

025.2141 NC Implant analogfor Multi-base abutment,straight

Ø 4.5 mm TAN

025.2106 NC Implant analogfor Multi-base abutment,angled 25°

Ø 4 mm TAN

Temporary restoration, for Multi-base abutment

024.2332 NC Temporary copingfor Multi-base abutment,straight

Ø 3.5 mm Ti

024.2342 NC Temporary copingfor Multi-base abutment,straight

Ø 4.5 mm Ti

024.2307 NC Temporary copingfor Multi-base abutment,angled 25°

Ø 4 mm Ti

024.2331-04 NC Protective capfor Multi-base abutment,straight

Ø 3.5 mm PEEK/TAN

024.2341-04 NC Protective capfor Multi-base abutment,straight

Ø 4.5 mm PEEK/TAN

024.2306-04 NC Protective capfor Multi-base abutment,angled 25°

Ø 4 mm PEEK/TAN


PRO

STH

ETIC

S

194



Coping, for Multi-base abutment

023.2731 NC Copingfor bridge on Multi-baseabutment, straight

Ø 3.5 mm Ceramicor®/POM



023.2701 NC Copingfor bridge on Multi-baseabutment, angled 25°

Ø 4 mm Ceramicor®/POM


Ø 3.5 mm POM


Ø 4.5 mm POM

023.2704 NC Copingfor bridge on Multi-baseabutment, angled 25°

Ø 4 mm POM

Auxiliary parts

025.0900-04 NC/RC Occlusal screwfor coping on Multi-baseabutment only

Length 4.5 mm TAN



PRO

STH

ETICS

195

CROWNS AND BRIDGESNARROW CrossFit®AUXILIARY PARTS


Auxiliary parts

025.2920025.2920-04




Length 4.5 mm TAN



PRO

STH

ETIC

S

196

CROWNS AND BRIDGESREGULAR CrossFit®IMPRESSION TAKING AND SOFT TISSUE MANAGEMENT



025.4201 RC Impression postfor closed tray, with 1 guidescrew and 2 caps

Length 12.3 mm TAN/POM

025.4202 RC Impression postfor open tray, short, withguide screw

Length 16.5 mm TAN

025.4205 RC Impression postfor open tray, long, with guidescrew

Length 24 mm TAN

025.4101 RC Implant analog Length 12 mm Ti

025.4102 RC Repositionable implantanalogfor fully digital andconventional workflow

Length 17 mm Ti

Bite registration

025.4208-04 RC Bite registration aid Height 8 mm POM

025.4212-04 RC Bite registration aid Height 12 mm POM


024.4370 RC Temporary abutment Height 12 mm,Ø 7 mm

PEEK/TAN

024.4371 RC Temporary abutmentfor crown


TAN

024.4375 RC Temporary abutmentfor bridge


TAN

Auxiliary parts




ImportantRC prosthetic components can only be used with Straumann® Bone Level implants, Ø 4.1 and Ø 4.8 mm, RegularCrossFit®.

PRO

STH

ETICS

197

CROWNS AND BRIDGESREGULAR CrossFit®GOLD, ANATOMIC IPS e.max® ABUTMENT



022.4430 RC Gold abutmentfor bridge



022.4410 RC Gold abutmentfor crown


022.4812 RC Straumann® AnatomicIPS e.max® abutmentstraight




ZrO2/MO 0

022.4822 RC Straumann® AnatomicIPS e.max® abutmentangled 15°




ZrO2/MO 0





ZrO2/MO 1





ZrO2/MO 1



PRO

STH

ETIC

S

198

CROWNS AND BRIDGESREGULAR CrossFit®ANATOMIC, MESO ABUTMENT



022.4102 RC Anatomic abutmentstraight


022.4104 RC Anatomic abutmentstraight


Ti

022.4152 RC Anatomic abutmentangled 15°


022.4154 RC Anatomic abutmentangled 15°


Ti

022.4202 RC Meso abutment Height 13.4 mm,Ø 8 mm

Ti

Auxiliary parts

025.4920025.4920-04

RC Polishing aid Length 16 mm Stainlesssteel


025.4902 RC Basal screwfor gold abutment, for bridgeonly

Length 8.3 mm TAN




PRO

STH

ETICS

199

CROWNS AND BRIDGESREGULAR CrossFit®CEMENTABLE ABUTMENT


All-in-One Sets

027.4313 RC CementableAll-in-One Setfor crown




















PRO

STH

ETIC

S

200



All-in-One Sets


Ø 6.5 mm,Abutment height 5.5 mm,Gingiva height 1 mm






022.4321 RC Cementable abutment Ø 5 mm,Gingiva height 1 mm,Abutment height 4 mm

Ti


Ti


Ti

022.4325 RC Cementable abutment Ø 5 mm,Gingiva height 1 mm,Abutment height 5.5 mm

Ti


Ti


Ti



PRO

STH

ETICS

201




022.4331 RC Cementable abutment Ø 6.5 mm,Gingiva height 1 mm,Abutment height 4 mm

Ti


Ti


Ti

022.4335 RC Cementable abutment Ø 6.5 mm,Gingiva height 1 mm,Abutment height 5.5 mm

Ti


Ti


Ti



PRO

STH

ETIC

S

202



Impression taking (abutment level) and master cast fabrication, for cementable abutment

025.4203-04 RC Impression capfor cementable abutment


POM



POM



POM



POM

025.4132 RC Implant analogfor cementable abutment


TAN



TAN



TAN



TAN


PRO

STH

ETICS

203



Temporary restoration, for cementable abutment

024.4356 RC Temporary copingfor cementable abutment

Ø 5 mm PMMA

024.4366 RC Temporary copingfor cementable abutment

Ø 6.5 mm PMMA

024.4322-04 RC Protective capfor cementable abutment


PEEK



PEEK



PEEK



PEEK


PRO

STH

ETIC

S

204



Coping, for cementable abutment

023.4320 RC Copingfor bridge on cementableabutment

Ø 5 mm POM

023.4326 RC Copingfor crown on cementableabutment

Ø 5 mm POM

023.4330 RC Copingfor bridge on cementableabutment

Ø 6.5 mm POM

023.4336 RC Copingfor crown on cementableabutment

Ø 6.5 mm POM

Auxiliary parts

025.4912-04 RC Transfer aidfor cementable abutment

Ø 5 mm PC

025.4913-04 RC Transfer aidfor cementable abutment

Ø 6.5 mm PC

025.4908 RC Basal screwfor cementable abutment only

Length 7.9 mm TAN



PRO

STH

ETICS

205

BRIDGESREGULAR CrossFit®MULTI-BASE ABUTMENT



022.4741 RC Multi-base abutmentstraight


TAN



TAN



TAN



TAN



TAN



TAN

022.4782 RC Multi-base abutmentangled 25°, type A


TAN

022.4786 RC Multi-base abutmentangled 25°, type B


TAN



PRO

STH

ETIC

S

206



Impression taking (abutment level) and master cast fabrication, for Multi-base abutment

025.4241-04 RC Impression capfor Multi-base abutment,straight

Ø 4.5 mm POM

025.4261-04 RC Impression capfor Multi-base abutment,straight

Ø 6.5 mm POM

025.4242 RC Impression postfor Multi-base abutment,straight

Ø 4.5 mm TAN

025.4262 RC Impression postfor Multi-base abutment,straight

Ø 6.5 mm TAN

025.4206 RC Impression postfor Multi-base abutment,angled 25°

Ø 4 mm TAN

025.4141 RC Implant analogfor Multi-base abutment,straight

Ø 4.5 mm TAN

025.4161 RC Implant analogfor Multi-base abutment,straight

Ø 6.5 mm TAN

025.4106 RC Implant analogfor Multi-base abutment,angled 25°

Ø 4 mm TAN

Temporary restoration, for Multi-base abutment

024.4342 RC Temporary copingfor Multi-base abutment,straight

Ø 4.5 mm Ti

024.4362 RC Temporary copingfor Multi-base abutment,straight

Ø 6.5 mm Ti

024.4307 RC Temporary copingfor Multi-base abutment,angled 25°

Ø 4 mm Ti

024.4341-04 RC Protective capfor Multi-base abutment,straight

Ø 4.5 mm PEEK/TAN

024.4361-04 RC Protective capfor Multi-base abutment,straight

Ø 6.5 mm PEEK/TAN

024.4306-04 RC Protective capfor Multi-base abutment,angled 25°

Ø 4 mm PEEK/TAN


PRO

STH

ETICS

207



Coping, for Multi-base abutment

023.4741 RC Copingfor bridge on Multi-baseabutment, straight




023.4701 RC Copingfor bridge on Multi-baseabutment, angled 25°

Ø 4 mm Ceramicor®/POM


Ø 4.5 mm POM


Ø 6.5 mm POM

023.4704 RC Copingfor bridge on Multi-baseabutment, angled 25°

Ø 4 mm POM

Auxiliary parts


Length 4.5 mm TAN



PRO

STH

ETIC

S

208

CROWNS AND BRIDGESREGULAR CrossFit®AUXILIARY PARTS


Auxiliary parts

025.4920025.4920-04



025.4902 RC Basal screwfor gold abutment, for bridgeonly

Length 8.3 mm TAN

025.4908 RC Basal screwfor cementable abutment only

Length 7.9 mm TAN


Length 4.5 mm TAN



PRO

STH

ETICS

209

HYBRID DENTURESNARROW CrossFit®LOCATOR® ABUTMENT


LOCATOR® Abutment

022.2502 NC LOCATOR® Abutment Height 2 mm TAV









PRO

STH

ETIC

S

210





Ti/Nylon


Height 1.7 mm Nylon


Height 1.7 mm Nylon


Height 1.7 mm Nylon





PRO

STH

ETICS

211





Ti/Nylon


Height 1.7 mm Nylon


Height 1.7 mm Nylon


Height 1.7 mm Nylon


Height 1.7 mm Nylon





PRO

STH

ETIC

S

212




025.0120-04 LOCATOR® Female analog Length 10 mm,Ø 4 mm

Al

048.197V4 LOCATOR® Impression coping Height 4 mm Al housingwith LDPEinsert

048.196V20 LOCATOR® Block-out spacer Thickness 0.4 mm Siliconerubber

048.195V4 LOCATOR® Black processingmale

Height 1.9 mm LDPE

048.218V4 LOCATOR® Processing spacer POM

046.413V4 LOCATOR® Abutment holdersleeve

PSU

Auxiliary parts









Stainlesssteel



PRO

STH

ETICS

213

HYBRID DENTURESNARROW CrossFit®BAR



022.2701 NC Abutmentfor bars, gold

Height 10 mm Ceramicor®



TAN



TAN



TAN



TAN



TAN



TAN



TAN



TAN

023.2732 NC Copingfor bar on Multi-base abutment,straight

Ø 3.5 mm Ceramicor®



023.2702 NC Copingfor bar on Multi-base abutment,angled 25°

Ø 4 mm Ceramicor®



PRO

STH

ETIC

S

214






Elitor®

048.412 Dolder® baregg-shaped cross-section, regular


Elitor®



Elitor®/Brass



Elitor®/Brass



PRO

STH

ETICS

215



Auxiliary parts









Length 4.5 mm TAN

025.0911-04 NC/RC Stabilization pinfor bar on Multi-base abutment



PRO

STH

ETIC

S

216



Components for titanium bars

022.2702 NC Abutmentfor bars

Height 10 mm Ti



TAN



TAN



TAN



TAN



TAN



TAN



TAN



TAN


Ø 3.5 mm Ti


Ø 4.5 mm Ti

023.2706 NC Copingfor bar on Multi-base abutment,angled 25°

Ø 4 mm Ti



PRO

STH

ETICS

217






Ti

048.465 Titanium baregg-shaped cross-section, regular


Ti



Ti/Brass



Ti/Brass



PRO

STH

ETIC

S

218



Auxiliary parts



PMMA



PMMA



Ti/Brass



Ti/Brass



Length 4.5 mm TAN


PRO

STH

ETICS

219

HYBRID DENTURESNARROW CrossFit®AUXILIARY PARTS


Auxiliary parts

025.2920025.2920-04




Length 4.5 mm TAN





PRO

STH

ETIC

S

220

HYBRID DENTURESREGULAR CrossFit®LOCATOR® ABUTMENT


LOCATOR® Abutment

022.4501 RC LOCATOR® Abutment Height 1 mm TAV










PRO

STH

ETICS

221





Ti/Nylon


Height 1.7 mm Nylon


Height 1.7 mm Nylon


Height 1.7 mm Nylon





PRO

STH

ETIC

S

222





Ti/Nylon


Height 1.7 mm Nylon


Height 1.7 mm Nylon


Height 1.7 mm Nylon


Height 1.7 mm Nylon





PRO

STH

ETICS

223




025.0120-04 LOCATOR® Female analog Length 10 mm,Ø 4 mm

Al

048.197V4 LOCATOR® Impression coping Height 4 mm Al housingwith LDPEinsert

048.196V20 LOCATOR® Block-out spacer Thickness 0.4 mm Siliconerubber

048.195V4 LOCATOR® Black processingmale

Height 1.9 mm LDPE

048.218V4 LOCATOR® Processing spacer POM

046.413V4 LOCATOR® Abutment holdersleeve

PSU

Auxiliary parts









Stainlesssteel



PRO

STH

ETIC

S

224

HYBRID DENTURESREGULAR CrossFit®BAR



022.4701 RC Abutmentfor bars, gold

Height 10 mm Ceramicor®



TAN



TAN



TAN



TAN



TAN



TAN



TAN



TAN

023.4742 RC Copingfor bar on Multi-base abutment,straight




023.4702 RC Copingfor bar on Multi-base abutment,angled 25°

Ø 4 mm Ceramicor®



PRO

STH

ETICS

225






Elitor®

048.412 Dolder® baregg-shaped cross-section, regular


Elitor®



Elitor®/Brass



Elitor®/Brass



PRO

STH

ETIC

S

226



Auxiliary parts









Length 4.5 mm TAN




PRO

STH

ETICS

227




022.4702 RC Abutmentfor bars

Height 10 mm Ti



TAN



TAN



TAN



TAN



TAN



TAN



TAN



TAN


Ø 4.5 mm Ti


Ø 6.5 mm Ti

023.4706 RC Copingfor bar on Multi-base abutment,angled 25°

Ø 4 mm Ti



PRO

STH

ETIC

S

228






Ti

048.465 Titanium baregg-shaped cross-section, regular


Ti



Ti/Brass



Ti/Brass



PRO

STH

ETICS

229



Auxiliary parts



PMMA



PMMA



Ti/Brass



Ti/Brass



Length 4.5 mm TAN


PRO

STH

ETIC

S

230

HYBRID DENTURESREGULAR CrossFit®AUXILIARY PARTS


Auxiliary parts

025.4920025.4920-04




Length 4.5 mm TAN





PRO

STH

ETICS

PROSTHETICS

STRAUMANN® CLASSIC

PRO

STH

ETICS

231

1250

When patients and dentists decide on a dental implant, they rely entirely on the product. As a manufacturer of dental implants, Straumann has been well acquainted with these demands for almost 40 years.

Straumann’s commitment – As a pioneer in implant dentistry, Straumann is committed to supporting the millions of patients with Straumann® dental implants and original prosthetic components as exclusive distributor.

Implant-borne prosthetic products show signs of wear over a long period, just like crowns and bridges on natural teeth. Straumann is therefore launching Straumann® Classic components.

Straumann® Classic stands for Confidence Reliability Durability Peace of mind

Straumann® Classic is Straumann’s commitment to supply prosthetic components for all Straumann® implant types listed in this catalog in the event of the need for a repeat restoration.

If your patient received a Straumann® implant after 1974, you can order an appropriate prosthetic component through Straumann® Classic.

Straumann® Classic – An additional service for patients and dentists who trust Straumann® products.

For a smooth and rapid repeat restoration with Straumann® Classic components, contact Straumann and ask for our system experts.

Manufacturer Diener AG Precision Machining CH-8424 Embrach Switzerland

Exclusively distributed by Institut Straumann AG, CH-4002 Basel, Switzerland

PRO

STH

ETIC

S

INTRODUCTION

232

Various prosthetic reconstruction options are possible for new restorations of implants (1974–1999).

Prosthetic components and remanufactured Straumann® Classic components from this catalog are available for the implant types listed in this catalog. Straumann® Classic components are indicated by a “C” at the end of the article number.

Recommendation for repeat restorations Please use articles from the current Straumann® Product Catalog as a first choice; only use the Straumann® Classic products indicated by a “C” if you require specific characteristics.

PRO

STH

ETICS

GENERAL GUIDELINES

233

PRO

STH

ETIC

S

234

C, E, F, H AND K IMPLANT TYPES


The following articles are required to restore these implant types with prosthetic components:

040.919C Classic Set, type C, E, F,H and Kset contents:9° impression cap,Implant analog,Gold coping,Occlusal screw

Al/Stainlesssteel/Ceramicor®/Ti*

* = Ceramicor® is a non-oxidizing precious metal alloy for casting on precious metal alloys.

● Manufactured from 1974 to 1980● Indications: These implant types were mainly used for bar solutions, but also for crown and bridge solutions

PRO

STH

ETICS

235

TPS IMPLANT TYPE, ONE-PART IMPLANT



040.920C Classic Set, TPS implanttypeset contents:TPS impression cap,TPS implant analog,TPS gold coping,TPS occlusal screw,L 4 mm

Al/Stainlesssteel/Elitor®/Ti*

* = Elitor® is a precious metal alloy for soldering and laser welding of precious metal alloys.

● Manufactured from 1980 to 1996● Indication: This implant type was used for one-part bar solutions

PRO

STH

ETIC

S

236

8° IMPLANT TYPE, ONE-PART IMPLANT



040.921C Classic Set, 8° typeset contents:Impression cap for 8º barhead,Implant protective cap for8º bar head,Implant analog for 8º barhead,Gold coping,SCS Occlusal screw,L 4 mm

Al/PEEK/Stainlesssteel/Ceramicor®/Ti*


● Manufactured from 1994 to 1999● Indication: This implant type was used for bar solutions● Prosthetic restorations for monotype 8° implant also possible

PRO

STH

ETICS

237

BONEFIT 45° SHOULDER IMPLANT TYPE

The following articles are required to restore this implant type with prosthetic components:


Restoration for fixed, cement-retained crowns and bridges

048.483C Abutment, angled 15º Ti


Restoration for fixed, screw-retained crowns and bridges

048.404C Octa abutment Height 1.5 mm Ti

Classic Set, Octa type

040.922C Classic Set, Octa typeset contents:Octa impression cap,RN implant analog,SCS Guide screw

Al/Stainlesssteel/Ti

Restoration for dentures — Bar on Octa abutment

048.404C Octa abutment Height 1.5 mm Ti

● Manufactured from 1989 to 1998● Indication: This implant type was used for screw-retained or cement-retained crowns, bridges, and telescopic and

bar solutions

For screw-retained repeat restorations, one impression set is required per implant.

synOcta® copings can be used according to current Straumann® Product Catalog.

LOCATOR® (article according to current Straumann® Product Catalog)

PRO

STH

ETIC

S

238

30°/45° SHOULDER HOLLOW CYLINDER IMPLANTS WITH LABIALBEVEL — WITH ANGULATION, WITHOUT ANGULATION





● Manufactured from 1988 to 1995● Indication: This implant type was used for cement-retained crowns and bridges; for implants with angulation, the

placement of angled abutments is not recommended● Solid abutment (article according to current Straumann® Product Catalog)

PRO

STH

ETICS

239

OCTA IMPLANT, 45°, ONE-PART IMPLANT



040.922C Classic Set, Octa typeset contents:Octa impression cap,RN implant analog,SCS Guide screw

Al/Stainlesssteel/Ti

● Manufactured from 1995 to 1999● Indication: this implant type was used for bar solutions

synOcta® copings can be used according to current Straumann® Product Catalog.

PRO

STH

ETIC

S

240

INSTRUMENTS/OTHER COMPONENTS THAT CAN BE ORDERED


Instruments

046.045C Driver for Octa abutment Stainlesssteel

046.114C Cross-tip screwdriver Stainlesssteel

Other components that can be ordered

048.220C Plastic coping forabutment 8°

POM

048.232C TS gold coping for Octa Ceramicor®*

048.304C Occlusal screw Length 15 mm Ti

048.312C TPS occlusal screw Length 8 mm Ti

048.424C Pin abutment Ceramicor®*

048.448C TS post for Octa Ti


The application area for the instruments is given on the next page.

The application area for the components is given on the next page.

The following list gives an overview of which implant types each of the components can be used for.

For a smooth and rapid repeat restoration with Straumann® Classic components, contact Straumann and ask for our system experts.

Article Description C, E, F, H and K

TPS Mono 8° Octa post Octa TS post

Bonefit 45°

046.114C Cross-tip screwdriver

048.304C Occlusal screw, L 15 mm

048.312C TPS occlusal screw, L 8 mm

048.220C Plastic coping for abutment 8º

046.045C Driver for Octa abutment

048.448C TS post for Octa

048.404C Octa abutment, H 1.5 mm

048.232C TS gold coping for Octa

048.424C Pin abutment

048.483C Abutment, angled 15º

048.484C Abutment, angled 20°

(048.672) (synOcta® thread protection screw)

(049.154) (Transversal screw)

(046.420) (TS screwdriver)

PRO

STH

ETICS

APPLICATION AREA FOR COMPONENTS

241

SER

VIC

E

SERVICE

SER

VIC

E

243


SER

VIC

E

244

SERVICE MATERIALS


5:1 Models

140.122 Straumann® Standard Plus NNC Implantconsisting of: NNC Standard Plus implant,NNC Healing cap with labial bevel, NNCImpression post for open tray, NNC Implantanalog, NNC Cementable angledabutment, NNC Solid abutment, NNCImpression cap for Solid abutment, NNCPositioning cylinder, SCS Screwdriver,plastic box

Metal/Plastic

140.019 Straumann® Standard Plus (NN) Implantconsisting of:NN Standard Plus implant, NN Healingcap with integr. occlusal screw,NN Impression cap, NN Protective capwith integr. occlusal screw, NN Analog,NN Framework blank, NN Titaniumabutment coping, SCS Screwdriver, plasticbox

Metal/Plastic

140.024 synOcta® systemconsisting of:Standard Plus Implant, RN Impression cap,RN synOcta® positioning cylinder,RN synOcta® analog, RN synOcta® abutment, SCS Screwdriver,RN synOcta® gold coping with plasticcrown,SCS Occlusal screw, plastic box

Metal/Plastic

120.0033 Straumann® Bone Level Implantconsisting of:RC Implant, RC Healing abutment, bottleshape, RC Impression post for open tray,RC Analog, RC Anatomic abutment, angled15°, occlusal screw, SCS Screwdriver,plastic box

Metal/Plastic

140.062 Straumann® Tapered Effect ImplantØ 4.1 mm, RN, SLA® 10 mm, cardboardbox

Stainless steel

SER

VIC

E

245

SERVICE MATERIALS


1:1 Models

140.032 Lower jawedentulous, with 2 implants, (S Ø 4.1 mm, RN)

Plastic,acrylic-glass/Ti

140.049 Lower jawedentulous, with 4 implants, (S Ø 4.1 mm, RN)


140.033 Upper jawtwo single-tooth gaps and unilateral free-endsaddle, with 4 implants1 x Standard Plus implant Ø 3.3 mm, NN1 x Standard implant Ø 4.8 mm, WN1 x Standard implant Ø 4.1 mm, RN1 x Standard implant Ø 4.8 mm, RN


For all users Product catalog Product information

For surgical dentists and surgeons Surgical information ITI Consensus Paper

For prosthetic dentists and dental technicians Prosthetic information ITI Consensus Paper

Our detailed documentation will assist you in carefully planning your implant-based restoration. Ask your customer service representative.

SER

VIC

E

SERVICE MATERIALS

246

INDEX

INDEX

INDEX

247


INDEX

248

NUMERICAL INDEX

Art. No. Article Page

118, 181Straumann® CARES® Wax-up kit for Camlog®019.0050

118, 181Straumann® CARES® Wax-up kit for NobelReplace™019.0051

118, 181Straumann® CARES® Wax-up kit019.0063

27Straumann® gonyX™019.0201

27NSK® handpiece for gonyX™019.0212

27NSK® control unit EU019.0213

27NSK® control unit NA019.0216

26coDiagnostiX™ 8 PPP019.0370

26coDiagnostiX™ 8 PPG019.0371

26coDiagnostiX™ 8 Station019.0372

26coDiagnostiX™ 8 coDoctor™019.0373

26coDiagnostiX™ unit019.0374

56Bone Level implant021.2108













58Bone Level implant021.4108G





















185NC Anatomic abutment022.2102




185NC Meso abutment022.2202

187NC Cementable abutment022.2311












184NC Gold abutment022.2410

209NC LOCATOR® Abutment022.2502



INDEX

249

NUMERICAL INDEX




213NC Abutment022.2701

216NC Abutment022.2702

192, 213, 216NC Multi-base abutment022.2731








184NC Straumann® Anatomic IPS e.max® abutment022.2812








198RC Anatomic abutment022.4102




198RC Meso abutment022.4202

200RC Cementable abutment022.4321












197RC Gold abutment022.4410

197RC Gold abutment022.4430

220RC LOCATOR® Abutment022.4501






224RC Abutment022.4701

227RC Abutment022.4702

205, 224, 227RC Multi-base abutment022.4741








197RC Straumann® Anatomic IPS e.max® abutment022.4812








191NC Coping023.2310




INDEX

250

NUMERICAL INDEX














204RC Coping023.4320
















56, 57NC Closure screw024.2100-04

56, 57NC Closure screw024.2105-04

56, 57NC Healing abutment024.2222









193NC Protective cap024.2306-04

193NC Temporary coping024.2307











182NC Temporary abutment024.2370



58, 60RC Closure screw024.4100-04

58, 60RC Closure screw024.4105-04

58, 60RC Healing abutment024.4222









206RC Protective cap024.4306-04

206RC Temporary coping024.4307

INDEX

251

NUMERICAL INDEX












196RC Temporary abutment024.4370



212, 223LOCATOR® Female analog025.0120-04

194, 195, 207, 208,215, 218, 219, 226,

229, 230

NC/RC Occlusal screw025.0900-04

215, 219, 226, 230NC/RC Stabilization pin025.0911-04

182NC Implant analog025.2101

180, 182NC Repositionable implant analog025.2102








182NC Impression post025.2201


189NC Impression cap025.2203-04




182NC Bite registration aid025.2208-04

182NC Bite registration aid025.2212-04






172NC PLAN Anatomic abutment025.2601-04




172NC PLAN Gold abutment025.2610-04

173NC PLAN Cementable abutment025.2611-04












177NC PLAN LOCATOR® Abutment025.2642-04





175NC PLAN Multi-base abutment025.2651-04





INDEX

252

NUMERICAL INDEX





180, 183, 185, 195, 215,218, 219

NC Basal screw025.2900

180NC Scanbody025.2901-04

180NC Wax-up sleeve025.2903

180NC Straumann® Scanbody025.2905

180NC Basal screw025.2906

191NC Basal screw025.2908

191NC Transfer aid025.2911-04

191NC Transfer aid025.2912-04

180NC Straumann® CARES® Mono Scanbody025.2915

185, 195, 219NC Polishing aid025.2920

196RC Implant analog025.4101

181, 196RC Repositionable implant analog025.4102








196RC Impression post025.4201


202RC Impression cap025.4203-04




196RC Bite registration aid025.4208-04

196RC Bite registration aid025.4212-04







172RC PLAN Anatomic abutment025.4601-04




172RC PLAN Gold abutment025.4610-04

174RC PLAN Cementable abutment025.4621-04






172RC PLAN Gold abutment025.4630-04







177RC PLAN LOCATOR® Abutment025.4641-04






176RC PLAN Multi-base abutment025.4651-04






INDEX

253

NUMERICAL INDEX




180, 196, 198, 208,226, 229, 230

RC Basal screw025.4900

181RC Scanbody025.4901-04

198, 208RC Basal screw025.4902

180RC Wax-up sleeve025.4903

181RC Straumann® Scanbody025.4905

180RC Basal screw025.4906

204, 208RC Basal screw025.4908

204RC Transfer aid025.4912-04

204RC Transfer aid025.4913-04

181RC Straumann® CARES® Mono Scanbody025.4915

198, 208, 230RC Polishing aid025.4920

172CrossFit® PLAN set026.0101

172CrossFit® PLAN cassette026.0102

30Bone Level implant distance indicator026.0901

10148h Explantation device026.2048

86BL/NNC Profile drill026.2303


80, 86BL/TE/NNC Tap for adapter026.2310


71BL/TE/NNC Tap026.2510

100NC Guiding cylinder026.2801


88BL Profile drill026.4303


82, 88BL/TE Tap for adapter026.4310


71BL/TE Tap026.4510

100RC Guiding cylinder026.4801



84, 90BL/TE Tap for adapter026.6310


71BL/TE Tap026.6510

100RC Guiding cylinder026.6801

186NC Cementable All-in-One Set027.4301









199RC Cementable All-in-One Set027.4313












38Standard implant033.030S

38Standard implant033.031G








INDEX

254

NUMERICAL INDEX


46Standard Plus implant033.050S

46Standard Plus implant033.051G





























42Standard Plus Implant033.416S



























53Tapered Effect implant033.712S










INDEX

255

NUMERICAL INDEX



52Tapered Effect implant033.761G











73Surgical cassette034.001

72Connector034.005

69Stop key034.006

69Mucosa punch034.010



73Sleeve034.050V4

73Sleeve034.052V4

73T-sleeve034.053V4

73T-sleeve034.055V4

27Closing lid034.056-04

27Sleeve positioner034.057

27Closing lid034.058-04

27Sleeve positioner034.059

28Stepped drill034.060

28Stepped drill034.061

28templiX reference plate034.062-03

27Reference pin034.064-03

27gonyX™ drill set034.066

28Girrbach Splitex® Counter plate034.069V5

68Pilot drill034.123



72Drill handle034.150

68Milling cutter034.215

68Twist drill PRO034.223



70SP Profile drill034.235

70TE Profile drill034.237

71S/SP Tap034.245


72Template fixation pin034.255








71S/SP Tap034.445







71S/SP Tap034.645



72C-handle H2034.750



96Straumann® Surgical cassette040.165

96Ultrasonic cleaning cassette040.175

INDEX

256

NUMERICAL INDEX


104Prosthetic cassette040.185

150Bar set gold040.195

152Bar set titanium040.196

153Bar set plastic040.197

91Surgical instruments starter set, Ø 4.1 mm for preparation by hand040.320

92Surgical instruments starter set, Ø 4.8 mm, for preparation by hand040.321

91Surgical instruments starter set, Ø 4.1 mm, Tap for adapter, for preparation using the handpiece,040.330

92Surgical instruments starter set, Ø 4.8 mm, Tap for adapter, for preparation using the handpiece040.331

22Screwdriver040.360

66Drill set040.440S

66Drill set040.441S

66Drill set040.443S

66Drill set040.444S

66Drill set040.446S

66Drill set040.447S

67Refill package: Drill stop set040.454S




67Drill stop kit040.460

67Drill stop aid040.461

97Osteotome instrument kit040.500

98Osteotome instrument kit040.501

143RN Solid All-in-One Set040.740



146WN Solid All-in-One Set040.745







234Classic Set, type C, E, F, H and K040.919C

235Classic Set, TPS implant type040.920C

236Classic Set, 8° type040.921C

237, 239Classic Set, Octa type040.922C

104Prosthetic cassette041.022

22Straumann® Bone Block Fixation041.032

96Screw container041.047

104Tray041.211

104Calibration cup041.412

104Dish041.440

96Storage system041.500

105Storage system041.501

104Divider041.612

104Divider041.615

22Crosshead mini-screw042.700V5




















INDEX

257

NUMERICAL INDEX







































74, 75, 77, 79, 81, 83,85, 87, 89

Round bur044.003

74, 75, 77, 79, 81, 83,85, 87, 89

Round bur044.004

74, 75, 77, 79, 81, 83,85, 87, 89

Round bur044.022







22Glide hole drill044.125

22Residual ridge drill044.126

74, 75, 77, 79, 81, 83,85, 87, 89

Pilot drill 1044.210

74, 75, 77, 79, 81, 83,85, 87, 89


74, 75, 77, 79, 81, 83,85, 87, 89


74, 75, 77, 79, 81, 83,85, 87, 89


75, 77, 81, 83, 87, 89Twist drill PRO044.250

75, 77, 81, 83, 87, 89Twist drill PRO044.251

77, 83, 89Twist drill PRO044.254

77, 83, 89Twist drill PRO044.255

93RN Bone profile drill044.304

93WN Bone profile drill044.305

99Explantation drill044.330



INDEX

258

NUMERICAL INDEX








132Tap044.570

74S/SP Tap044.575

76S/SP Tap044.577

78S/SP Tap044.579







94, 107Cleaning brush045.111V4

95Light curette for implants045.921

240Driver for Octa abutment046.045C

94, 107Torque control device046.049

94Tweezers046.057

94Holding key046.064

106, 143Solid abutment driver046.067

106, 143Solid abutment driver046.068

106, 155Retentive anchor driver046.069

106Screwdriver handle046.085

94Tweezers046.095

94, 107Service instrument046.108

94Instrument tweezers046.110

240Cross-tip screwdriver046.114C

94, 107Ratchet046.119

156Titanmagnetics® Insert applicator (driver)046.146

30Diagnostic T046.147

30Standard, Standard Plus and Tapered Effect implant distance indicator046.148

151, 215, 226Activator set046.150

151, 215, 226Deactivator046.151

151, 215, 226Deactivator046.152


107, 142NNC Reamer046.237

107, 119, 120, 122, 126,129, 132, 135, 136, 142,145, 148, 154, 183, 185,191, 194, 195, 196, 198,204, 207, 208, 219, 230

Analog holder046.239

107, 126, 129, 132, 135,136, 142, 145, 148

Handle046.240

107, 126, 135synOcta® Guide pin046.241

145Guide pin046.242

107, 126, 129, 135, 136,145, 148

Reamer046.243

148Guide pin046.244

126, 154Polishing protector046.245

107, 129Guide pin046.246

107, 136synOcta® Guide pin046.247

107, 142NNC Guide pin046.249

22Screwdriver blade046.256

22Screw-holding device046.257

22Screwdriver handle046.258

95, 106SCS Screwdriver046.400






160, 164, 168, 212, 223LOCATOR® Abutment holder sleeve046.413V4

106, 160, 164, 168, 212,223

LOCATOR® Core tool046.415

106, 160, 164, 168, 212,223

LOCATOR® Driver046.416

INDEX

259

NUMERICAL INDEX


106, 160, 164, 168,212, 223

LOCATOR® Driver046.417

132TS Hexagonal screwdriver046.420

95Hexagonal screwdriver046.421

75, 77, 81, 83, 87, 89Depth gauge046.450

77, 83, 89Depth gauge046.451

74, 75, 77, 79, 81, 83,85, 87, 89

Depth gauge046.455

74, 75, 77, 79, 81, 83,85, 87, 89

Alignment pin046.458

94Adapter046.460

94Adapter046.461

94Adapter046.462

94Adapter046.470

94Adapter046.471

94Adapter046.472

97Osteotome046.500

97Osteotome046.501

97Osteotome046.502

97Osteotome046.503

97Osteotome046.510

97Osteotome046.511

97Osteotome046.512

97Osteotome046.513

98Osteotome046.521

98Osteotome046.522

98Osteotome046.523

98Osteotome046.531

98Osteotome046.532

98Osteotome046.533

97Depth stop046.550

97, 98Depth stop046.551

97, 98Depth stop046.552

97, 98Depth stop046.553

130Transfer aid048.000V4



124RN synOcta® Impression post048.010

133, 146WN Impression cap048.013

156Titanmagnetics® impression coping048.014

123NN Impression cap048.016

124, 144RN Impression cap048.017V4

44, 45, 46, 47, 50, 51,52

RN Healing cap048.028

44, 45, 46, 47, 50, 51,52


40, 48, 53WN Healing cap048.030

137Transfer aid048.032

36, 37, 38, 39, 44, 45,46, 47, 50, 51, 52


36, 37, 38, 39, 44, 45,46, 47, 50, 51, 52


36, 37, 38, 39, 44, 45,46, 47, 50, 51, 52


40, 48, 53WN Healing cap048.038

40, 48, 53WN Healing cap048.039

43NN Healing cap048.043

144RN Protective cap048.047V4



43, 123NN Protective cap048.050

147WN Protective cap048.051

147WN Protective cap048.052

40, 48, 53WN Healing cap048.053



144Positioning cylinder048.060V4



INDEX

260

NUMERICAL INDEX


146Positioning cylinder048.065

146Positioning cylinder048.066

115NN Straumann® Scanbody048.067

116RN Straumann® Scanbody048.068

117WN Straumann® Scanbody048.069

124RN synOcta® Positioning cylinder048.070V4

42NNC Healing cap048.071

154Fixation pin048.073V4



115NN Scanbody048.084V4

116RN Scanbody048.085V4

117WN Scanbody048.086V4

115NN Wax-up sleeve048.087

116RN Wax-up sleeve048.088

117WN Wax-up sleeve048.089

124RN synOcta® Impression post048.090

133WN synOcta® impression cap048.091

154RN synOcta® Impression cap048.093V4

133WN synOcta® positioning cylinder048.095

154RN synOcta® Analog048.108

64, 155Transfer pin048.109

144Shoulder analog048.117V4

156Titanmagnetics® model implant048.121

123NN Impression cap048.122V4

124RN synOcta® analog048.124

119NNC Implant analog048.127

119NNC Impression post048.128

116, 124RN Repositionable implant analog048.129

123NN Implant analog048.130

115, 123NN Repositionable implant analog048.132

119NNC Impression post048.134

146Shoulder analog048.140

139NNC Solid abutment driver048.155

139NNC Solid abutment driver048.156

144Analog048.160

144Analog048.161

144Analog048.162

146Analog048.165

146Analog048.166

115NN Straumann® CARES® Mono Scanbody048.167

116RN Straumann® CARES® Mono Scanbody048.168

117WN Straumann® CARES® Mono Scanbody048.169

133WN synOcta® analog048.171

117, 133WN Repositionable implant analog048.172

161RN LOCATOR® Abutment048.175






159, 163, 167, 211, 222LOCATOR® Replacement male048.181V4

159, 163, 167, 211, 222LOCATOR® Male processing package048.182V2

165WN LOCATOR® Abutment048.183






158, 162, 166, 210, 221LOCATOR® Male processing package048.189V2






160, 164, 168, 212, 223LOCATOR® Black processing male048.195V4

160, 164, 168, 212, 223LOCATOR® Block-out spacer048.196V20

INDEX

261

NUMERICAL INDEX


160, 164, 168, 212,223

LOCATOR® Impression coping048.197V4

160, 164, 168LOCATOR® Female analog048.198V4

160, 164, 168, 212,223

LOCATOR® Parallel post048.199V4

160, 164, 168, 212,223

LOCATOR® Angle measurement guide048.200

150RN synOcta® Gold coping048.204

151Stabilization pin for retaining gold copings in solder investment048.208V4

152RN synOcta® Titanium coping048.214

160, 164, 168, 212,223

LOCATOR® Processing spacer048.218V4

240Plastic coping for abutment 8°048.220C

126, 153RN synOcta® Plastic coping048.227

126RN synOcta® Plastic coping048.229

240TS gold coping for Octa048.232C

133WN synOcta® Post048.233

133WN synOcta® Post048.234

128RN synOcta® Milling cylinder048.240

128RN synOcta® Milling cylinder048.241

136WN synOcta® Plastic coping048.243


145Plastic coping048.245




120NNC Plastic coping048.256





112RN PLAN LOCATOR® Abutment048.275V4






112WN PLAN LOCATOR® Abutment048.283V4





240Occlusal screw048.304C

240TPS occlusal screw048.312C

119, 122NNC Basal screw048.313

119, 120NNC Basal screw048.314

42NNC Closure screw048.324

42NNC Closure screw048.325

101, 126, 127, 130,134, 134, 150, 152,

153, 169

SCS Occlusal screw048.350

115NN Occlusal screw048.353

116RN Occlusal screw048.354

116, 117, 125, 127synOcta® basal screw048.356

169SCS Guide screw048.360V4


128, 169SCS Guide screw048.362V4

128, 169SCS Guide screw048.363V4




36, 37, 38, 39, 44, 45,46, 47, 50, 51, 52

RN Closure screw048.371

36, 37, 38, 39, 44, 45,46, 47, 50, 51, 52

RN Closure screw048.373

43NN Closure screw048.374

40, 48, 53WN Closure screw048.375

237, 237Octa abutment048.404C

150, 214, 225Dolder® bar048.411

INDEX

262

NUMERICAL INDEX


150, 214, 225Dolder® bar048.412

150, 214, 225Dolder® bar matrix048.413

150, 214, 225Dolder® bar matrix048.414

240Pin abutment048.424C

155Retentive anchor abutment048.439

240TS post for Octa048.448C

155Titanium matrix048.450

155Spacer048.451V4


155Extractor048.453

155Threaded mounting ring048.454V4

155Spring048.455V4

155Elliptical matrix048.456

155Spare lamella retention insert048.457

153, 218, 229Plastic bar048.460

153, 218, 229Plastic bar048.461

152, 217, 228Titanium bar048.465

152, 217, 228Titanium bar048.466

152, 153, 217, 218, 228,229

Titanium bar matrix048.470

152, 153, 217, 218, 228,229

Titanium bar matrix048.471

237, 238Abutment, angled 15º048.483C

237, 238Abutment, angled 20º048.484C

123NN Framework blank048.500

119NNC Post048.501

119NNC Post048.502

123NN Coping048.505

156Titanmagnetics® insert (abutment)048.511

156Titanmagnetics® denture magnet048.515

156Positioning cuff048.516

140NNC Analog048.527



143RN Solid abutment 6°048.540



146WN Solid abutment 6°048.545

146WN Solid abutment 6°048.546

139NNC Solid abutment048.547



123NN Coping048.550

123NN Coping048.551

127RN synOcta® Meso milling cylinder048.571

134WN synOcta® Meso milling cylinder048.573

140NNC Impression cap048.579

157NNC LOCATOR® Abutment048.581






140NNC Positioning cylinder048.587



122NNC Gold abutment048.592

122NNC Gold abutment048.593

120NNC Cementable abutment048.598

126, 128, 150, 152RN synOcta® 1.5 screw-retained abutment048.601

134WN synOcta® 1.5 screw-retained abutment048.603

129RN synOcta® Cementable abutment048.605

136WN synOcta® cementable abutment048.606

137WN synOcta® 15° angled abutment048.608

137WN synOcta® 15° angled abutment048.609

130RN synOcta® 15° angled abutment048.610


INDEX

263

NUMERICAL INDEX








132RN synOcta® Transversal (TS) screw-retained abutment048.620





132RN synOcta® TS gold coping048.634

123NN Gold coping048.635

134WN synOcta® Gold coping048.638

134WN synOcta® Gold coping048.639

127RN synOcta® Gold abutment048.642

134WN synOcta® Gold abutment048.644

125RN synOcta® Post048.650

125RN synOcta® Post048.651

144RN Temporary coping048.654

144RN Temporary coping048.655

147WN Temporary coping048.656

147WN Temporary coping048.657

141NNC Temporary coping048.658

141NNC Temporary coping048.659



132RN synOcta® TS plastic coping048.665



125RN synOcta® Temporary Meso abutment048.668

123NN Temporary coping048.669

130Extension shell048.670

132RN synOcta® TS thread protection screw048.672

130Plastic shoulder048.676V4

137Plastic shoulder048.678

141NNC Protective cap048.700



110Prosthetic planning kit048.901

110Soft Tissue Level PLAN Set048.904

110Soft Tissue Level PLAN Cassette048.905

110RN synOcta® 15° angled PLAN abutment048.916V4




110RN synOcta® PLAN abutment048.920V4

110RN synOcta® Transversal PLAN abutment048.921V4





112RN PLAN Solid abutment048.926V4



110RN synOcta® 1.5 PLAN abutment048.929V4

111RN synOcta® Cementable PLAN abutment048.930V4

111WN synOcta® 1.5 PLAN abutment048.931V4

111WN synOcta® Cementable PLAN abutment048.932V4

111WN synOcta® 15° angled PLAN abutment048.933V4

111WN synOcta® 15° angled PLAN abutment048.934V4

112NN PLAN coping048.935V4

112NN angled PLAN coping 15°048.936V4

112NN angled PLAN coping 20°048.937V4

112WN PLAN Solid abutment 6°048.938V4

112WN PLAN Solid abutment 6°048.939V4

124, 133Bite registration aid048.940V4

INDEX

264

NUMERICAL INDEX


124, 133Bite registration aid048.941V4

100RN Guiding sleeve049.071

30X-ray reference sphere049.076V4

93, 100SCS Guiding cylinder049.082

100SCS Guiding cylinder049.083

132Transversal screw049.154


115, 123NN Occlusal screw049.177

101, 125, 133SCS Occlusal screw049.181






31Drill sleeve with collar049.810V4

31Pin049.816V4

31Pin049.817V4

31Stepped pin049.818V4

31Pin049.819V4



21Straumann® BoneCeramic 400–700070.203



20Straumann® Emdogain 0.3 ml075.101




20Straumann® Emdogain PLUS075.117

20Straumann® PrefGel 0.6 ml075.203

244Straumann® Bone Level Implant120.0033

244Straumann® Standard Plus (NN) Implant140.019

244synOcta® system140.024

245Lower jaw140.032

245Upper jaw140.033

245Lower jaw140.049

104Plexiglass cassette/Membranette140.055

244Straumann® Tapered Effect Implant140.062

244Straumann® Standard Plus NNC Implant140.122

30X-ray templates150.215



102Smartpeg™ Type 17174.020V5




64TempImplant bending tool80356

64TempImplant inserting device80363

64TempImplant80371SV4

64TempImplant80372SV4

64Drill80381

64TempImplant inserting device80398

64Dalbo®-Rotex® Matrix80399V4

INDEX

265

ALPHABETICAL INDEX

Article Art. No. Page

10148h Explantation device 026.4048





237, 238Abutment, angled 15º 048.483C

237, 238Abutment, angled 20º 048.484C

151, 215, 226Activator set 046.150

94Adapter 046.460

94Adapter 046.461

94Adapter 046.462

94Adapter 046.470

94Adapter 046.471

94Adapter 046.472

74, 75, 77, 79, 81, 83,85, 87, 89

Alignment pin 046.458

144Analog 048.160

144Analog 048.161

144Analog 048.162

146Analog 048.165

146Analog 048.166

107, 119, 120, 122,126, 129, 132, 135,136, 142, 145, 148,154, 183, 185, 191,194, 195, 196, 198,204, 207, 208, 219,

230

Analog holder 046.239

150Bar set gold 040.195

153Bar set plastic 040.197

152Bar set titanium 040.196

124, 133Bite registration aid 048.941V4

124, 133Bite registration aid 048.940V4

70BL Profile drill 026.4503






70BL/NNC Profile drill 026.2503



71BL/TE Tap 026.4510

71BL/TE Tap 026.6510

84, 90BL/TE Tap for adapter 026.6310

82, 88BL/TE Tap for adapter 026.4310

71BL/TE/NNC Tap 026.2510

80, 86BL/TE/NNC Tap for adapter 026.2310

56Bone Level implant 021.2110


















58Bone Level implant 021.4110G


INDEX

266

ALPHABETICAL INDEX
















30Bone Level implant distance indicator 026.0901

72C -handle H2 034.750

72C-handle H4 034.751

72C-handle H6 034.752

104Calibration cup 041.412

236Classic Set, 8° type 040.921C

237, 239Classic Set, Octa type 040.922C

235Classic Set, TPS implant type 040.920C

234Classic Set, type C, E, F, H and K 040.919C

94, 107Cleaning brush 045.111V4

27Closing lid 034.058-04

27Closing lid 034.056-04

26coDiagnostiX™ 8 coDoctor™ 019.0373

26coDiagnostiX™ 8 PPG 019.0371

26coDiagnostiX™ 8 PPP 019.0370

26coDiagnostiX™ 8 Station 019.0372

26coDiagnostiX™ unit 019.0374

72Connector 034.005

240Cross-tip screwdriver 046.114C

172CrossFit® PLAN cassette 026.0102

172CrossFit® PLAN set 026.0101

22Crosshead mini-screw 042.700V5




64Dalbo®-Rotex® Matrix 80399V4

151, 215, 226Deactivator 046.151

151, 215, 226Deactivator 046.152

74, 75, 77, 79, 81, 83, 85,87, 89

Depth gauge 046.455

75, 77, 81, 83, 87, 89Depth gauge 046.450

77, 83, 89Depth gauge 046.451

97Depth stop 046.550

97, 98Depth stop 046.551

97, 98Depth stop 046.552

97, 98Depth stop 046.553

30Diagnostic T 046.147

104Dish 041.440

104Divider 041.612

104Divider 041.615

150, 214, 225Dolder® bar 048.411

150, 214, 225Dolder® bar 048.412

150, 214, 225Dolder® bar matrix 048.413

150, 214, 225Dolder® bar matrix 048.414

64Drill 80381

72Drill handle 034.250




66Drill set 040.440S




INDEX

267

ALPHABETICAL INDEX




31Drill sleeve with collar 049.810V4

67Drill stop aid 040.461

67Drill stop kit 040.460

240Driver for Octa abutment 046.045C

155E lliptical matrix 048.456

99Explantation drill 044.330









130Extension shell 048.670

155Extractor 048.453

154Fixation pin 048.073V4

28Girrbach Splitex® Counter plate 034.069V5

22Glide hole drill 044.125

27gonyX™ drill set 034.066

107, 129Guide pin 046.246

145Guide pin 046.242

148Guide pin 046.244

107, 126, 129, 132,135, 136, 142, 145,

148

Handle 046.240

95Hexagonal screwdriver 046.421

94Holding key 046.064

94Instrument tweezers 046.110

95Light curette for implants 045.921

160, 164, 168, 212,223

LOCATOR® Abutment holder sleeve 046.413V4

160, 164, 168, 212,223

LOCATOR® Angle measurement guide 048.200

160, 164, 168, 212,223

LOCATOR® Black processing male 048.195V4

160, 164, 168, 212,223

LOCATOR® Block-out spacer 048.196V20

106, 160, 164, 168,212, 223

LOCATOR® Core tool 046.415

106, 160, 164, 168,212, 223

LOCATOR® Driver 046.416

106, 160, 164, 168,212, 223

LOCATOR® Driver 046.417

160, 164, 168LOCATOR® Female analog 048.198V4

212, 223LOCATOR® Female analog 025.0120-04

160, 164, 168, 212,223

LOCATOR® Impression coping 048.197V4

158, 162, 166, 210,221

LOCATOR® Male processing package 048.189V2

159, 163, 167, 211,222

LOCATOR® Male processing package 048.182V2

160, 164, 168, 212,223

LOCATOR® Parallel post 048.199V4

160, 164, 168, 212,223

LOCATOR® Processing spacer 048.218V4

158, 162, 166, 210,221

LOCATOR® Replacement male 048.192V4

158, 162, 166, 210,221


158, 162, 166, 210,221


159, 163, 167, 211,222


159, 163, 167, 211,222


159, 163, 167, 211,222


159, 163, 167, 211,222


INDEX

268

ALPHABETICAL INDEX


245Lower jaw 140.049

245Lower jaw 140.032

68Milling cutter 034.215



69Mucosa punch 034.011



213NC Abutment 022.2701

216NC Abutment 022.2702

185NC Anatomic abutment 022.2104




180NC Basal screw 025.2906

180, 183, 185, 195, 215,218, 219

NC Basal screw 025.2900

191NC Basal screw 025.2908

182NC Bite registration aid 025.2212-04

182NC Bite registration aid 025.2208-04

187NC Cementable abutment 022.2312












186NC Cementable All-in-One Set 027.4302









56, 57NC Closure screw 024.2105-04

56, 57NC Closure screw 024.2100-04

191NC Coping 023.2316

191NC Coping 023.2320

191NC Coping 023.2326

191NC Coping 023.2310

194NC Coping 023.2741

194NC Coping 023.2734

194NC Coping 023.2744

194NC Coping 023.2701

194NC Coping 023.2704

194NC Coping 023.2731

213NC Coping 023.2742

213NC Coping 023.2732

213NC Coping 023.2702

216NC Coping 023.2736

216NC Coping 023.2746

216NC Coping 023.2706

184NC Gold abutment 022.2410

100NC Guiding cylinder 026.2801

56, 57NC Healing abutment 024.2270






INDEX

269

ALPHABETICAL INDEX





182NC Implant analog 025.2101








189NC Impression cap 025.2204-04





182NC Impression post 025.2202






209NC LOCATOR® Abutment 022.2503





185NC Meso abutment 022.2202

192, 213, 216NC Multi-base abutment 022.2734








172NC PLAN Anatomic abutment 025.2602-04




173NC PLAN Cementable abutment 025.2612-04












172NC PLAN Gold abutment 025.2610-04

177NC PLAN LOCATOR® Abutment 025.2643-04





175NC PLAN Multi-base abutment 025.2652-04








185, 195, 219NC Polishing aid 025.2920

INDEX

270

ALPHABETICAL INDEX


193NC Protective cap 024.2331-04







180, 182NC Repositionable implant analog 025.2102

180NC Scanbody 025.2901-04

184NC Straumann® Anatomic IPS e.max® abutment 022.2812








180NC Straumann® CARES® Mono Scanbody 025.2915

180NC Straumann® Scanbody 025.2905

182NC Temporary abutment 024.2370



193NC Temporary coping 024.2342





191NC Transfer aid 025.2912-04

191NC Transfer aid 025.2911-04

180NC Wax-up sleeve 025.2903

194, 195, 207, 208, 215,218, 219, 226, 229, 230

NC/RC Occlusal screw 025.0900-04

215, 219, 226, 230NC/RC Stabilization pin 025.0911-04

112NN angled PLAN coping 15° 048.936V4

112NN angled PLAN coping 20° 048.937V4

43NN Closure screw 048.374

123NN Coping 048.505



123NN Framework blank 048.500

123NN Gold coping 048.635

43NN Healing cap 048.043

123NN Implant analog 048.130

123NN Impression cap 048.122V4

123NN Impression cap 048.016

115, 123NN Occlusal screw 049.177

115NN Occlusal screw 048.353

112NN PLAN coping 048.935V4

43, 123NN Protective cap 048.050

115, 123NN Repositionable implant analog 048.132

115NN Scanbody 048.084V4

115NN Straumann® CARES® Mono Scanbody 048.167

115NN Straumann® Scanbody 048.067

123NN Temporary coping 048.669

115NN Wax-up sleeve 048.087

140NNC Analog 048.527



119, 120NNC Basal screw 048.314

119, 122NNC Basal screw 048.313

120NNC Cementable abutment 048.621



42NNC Closure screw 048.325

42NNC Closure screw 048.324

122NNC Gold abutment 048.593

122NNC Gold abutment 048.592

INDEX

271

ALPHABETICAL INDEX


107, 142NNC Guide pin 046.249

42NNC Healing cap 048.071



119NNC Implant analog 048.127

140NNC Impression cap 048.579

119NNC Impression post 048.134

119NNC Impression post 048.128

157NNC LOCATOR® Abutment 048.582






142NNC Plastic coping 048.264





140NNC Positioning cylinder 048.587



119NNC Post 048.502

119NNC Post 048.501

141NNC Protective cap 048.700



107, 142NNC Reamer 046.237

139NNC Solid abutment 048.547



139NNC Solid abutment driver 048.156

139NNC Solid abutment driver 048.155

141NNC Temporary coping 048.659

141NNC Temporary coping 048.658

27NSK® control unit EU 019.0213

27NSK® control unit NA 019.0216

27NSK® handpiece for gonyX™ 019.0212

240Occlusal screw 048.304C

237, 237Octa abutment 048.404C

97Osteotome 046.500

97Osteotome 046.501

97Osteotome 046.502

97Osteotome 046.503

97Osteotome 046.510

97Osteotome 046.511

97Osteotome 046.512

97Osteotome 046.513

98Osteotome 046.521

98Osteotome 046.522

98Osteotome 046.523

98Osteotome 046.531

98Osteotome 046.532

98Osteotome 046.533

97Osteotome instrument kit 040.500

98Osteotome instrument kit 040.501

68Pilot drill 034.126



74, 75, 77, 79, 81, 83,85, 87, 89

Pilot drill 1 044.210

74, 75, 77, 79, 81, 83,85, 87, 89


74, 75, 77, 79, 81, 83,85, 87, 89


74, 75, 77, 79, 81, 83,85, 87, 89


31Pin 049.816V4

INDEX

272

ALPHABETICAL INDEX


31Pin 049.817V4

31Pin 049.819V4

240Pin abutment 048.424C

153, 218, 229Plastic bar 048.460

153, 218, 229Plastic bar 048.461

145Plastic coping 048.246




240Plastic coping for abutment 8° 048.220C

130Plastic shoulder 048.676V4

137Plastic shoulder 048.678

104Plexiglass cassette/Membranette 140.055

126, 154Polishing protector 046.245

156Positioning cuff 048.516

144Positioning cylinder 048.060V4



146Positioning cylinder 048.065

146Positioning cylinder 048.066

104Prosthetic cassette 040.185

104Prosthetic cassette 041.022

110Prosthetic planning kit 048.901

94, 107Ratchet 046.119

224RC Abutment 022.4701

227RC Abutment 022.4702

198RC Anatomic abutment 022.4104




180RC Basal screw 025.4906

180, 196, 198, 208, 226,229, 230

RC Basal screw 025.4900

198, 208RC Basal screw 025.4902

204, 208RC Basal screw 025.4908

196RC Bite registration aid 025.4212-04

196RC Bite registration aid 025.4208-04

201RC Cementable abutment 022.4332












199RC Cementable All-in-One Set 027.4314












58, 60RC Closure screw 024.4105-04

58, 60RC Closure screw 024.4100-04

204RC Coping 023.4326

204RC Coping 023.4330

204RC Coping 023.4336

204RC Coping 023.4320

INDEX

273

ALPHABETICAL INDEX


207RC Coping 023.4761

207RC Coping 023.4744

207RC Coping 023.4764

207RC Coping 023.4701

207RC Coping 023.4704

207RC Coping 023.4741

224RC Coping 023.4742

224RC Coping 023.4762

224RC Coping 023.4702

227RC Coping 023.4746

227RC Coping 023.4766

227RC Coping 023.4706

197RC Gold abutment 022.4410

197RC Gold abutment 022.4430

100RC Guiding cylinder 026.4801

100RC Guiding cylinder 026.6801

59, 61RC Healing abutment 024.4270









196RC Implant analog 025.4101








202RC Impression cap 025.4220-04






196RC Impression post 025.4202






220RC LOCATOR® Abutment 022.4502






198RC Meso abutment 022.4202

205, 224, 227RC Multi-base abutment 022.4742








172RC PLAN Anatomic abutment 025.4601-04




174RC PLAN Cementable abutment 025.4635-04



INDEX

274

ALPHABETICAL INDEX











172RC PLAN Gold abutment 025.4610-04

172RC PLAN Gold abutment 025.4630-04

177RC PLAN LOCATOR® Abutment 025.4641-04






176RC PLAN Multi-base abutment 025.4652-04








198, 208, 230RC Polishing aid 025.4920

206RC Protective cap 024.4341-04







181, 196RC Repositionable implant analog 025.4102

181RC Scanbody 025.4901-04

197RC Straumann® Anatomic IPS e.max® abutment 022.4812








181RC Straumann® CARES® Mono Scanbody 025.4915

181RC Straumann® Scanbody 025.4905

196RC Temporary abutment 024.4370



206RC Temporary coping 024.4362





204RC Transfer aid 025.4913-04

204RC Transfer aid 025.4912-04

180RC Wax-up sleeve 025.4903

107, 126, 129, 135, 136,145, 148

Reamer 046.243

27Reference pin 034.064-03

67Refill package: Drill stop set 040.454S




22Residual ridge drill 044.126

155Retentive anchor abutment 048.439

106, 155Retentive anchor driver 046.069

93RN Bone profile drill 044.304

INDEX

275

ALPHABETICAL INDEX


36, 37, 38, 39, 44, 45,46, 47, 50, 51, 52

RN Closure screw 048.371

36, 37, 38, 39, 44, 45,46, 47, 50, 51, 52

RN Closure screw 048.373

100RN Guiding sleeve 049.071



36, 37, 38, 39, 44, 45,46, 47, 50, 51, 52

RN Healing cap 048.034

36, 37, 38, 39, 44, 45,46, 47, 50, 51, 52


36, 37, 38, 39, 44, 45,46, 47, 50, 51, 52


44, 45, 46, 47, 50, 51,52


44, 45, 46, 47, 50, 51,52


124, 144RN Impression cap 048.017V4

161RN LOCATOR® Abutment 048.176






116RN Occlusal screw 048.354

112RN PLAN LOCATOR® Abutment 048.275V4






112RN PLAN Solid abutment 048.926V4



144RN Protective cap 048.047V4



116, 124RN Repositionable implant analog 048.129

116RN Scanbody 048.085V4

143RN Solid abutment 6° 048.540



143RN Solid All-in-One Set 040.741






116RN Straumann® CARES® Mono Scanbody 048.168

116RN Straumann® Scanbody 048.068

130RN synOcta® 15° angled abutment 048.610




110RN synOcta® 15° angled PLAN abutment 048.916V4




110RN synOcta® 1.5 PLAN abutment 048.929V4

126, 128, 150, 152RN synOcta® 1.5 screw-retained abutment 048.601









INDEX

276

ALPHABETICAL INDEX


154RN synOcta® Analog 048.108

124RN synOcta® analog 048.124

129RN synOcta® Cementable abutment 048.605

111RN synOcta® Cementable PLAN abutment 048.930V4

127RN synOcta® Gold abutment 048.642

150RN synOcta® Gold coping 048.204



154RN synOcta® Impression cap 048.093V4

124RN synOcta® Impression post 048.010

124RN synOcta® Impression post 048.090

127RN synOcta® Meso milling cylinder 048.571

128RN synOcta® Milling cylinder 048.241

128RN synOcta® Milling cylinder 048.240

110RN synOcta® PLAN abutment 048.920V4

126, 153RN synOcta® Plastic coping 048.227

126RN synOcta® Plastic coping 048.229



124RN synOcta® Positioning cylinder 048.070V4

125RN synOcta® Post 048.650

125RN synOcta® Post 048.651

125RN synOcta® Temporary Meso abutment 048.668

152RN synOcta® Titanium coping 048.214

110RN synOcta® Transversal PLAN abutment 048.921V4

132RN synOcta® Transversal (TS) screw-retained abutment 048.620

132RN synOcta® TS gold coping 048.634

132RN synOcta® TS plastic coping 048.665

132RN synOcta® TS thread protection screw 048.672

144RN Temporary coping 048.655

144RN Temporary coping 048.654

116RN Wax-up sleeve 048.088

74, 75, 77, 79, 81, 83, 85,87, 89

Round bur 044.003

74, 75, 77, 79, 81, 83, 85,87, 89

Round bur 044.004

74, 75, 77, 79, 81, 83, 85,87, 89

Round bur 044.022

96Screw container 041.047

22Screw-holding device 046.257

155Screwdriver 046.154



22Screwdriver blade 046.256

106Screwdriver handle 046.085

22Screwdriver handle 046.258

169SCS Guide screw 048.360V4





128, 169SCS Guide screw 048.362V4

128, 169SCS Guide screw 048.363V4

100SCS Guiding cylinder 049.360




93, 100SCS Guiding cylinder 049.082

101, 125, 133SCS Occlusal screw 049.181

101, 126, 127, 130, 134,134, 150, 152, 153, 169

SCS Occlusal screw 048.350

95, 106SCS Screwdriver 046.401






94, 107Service instrument 046.108

INDEX

277

ALPHABETICAL INDEX


144Shoulder analog 048.117V4

146Shoulder analog 048.140

73Sleeve 034.052V4

73Sleeve 034.050V4

27Sleeve positioner 034.059

27Sleeve positioner 034.057

102Smartpeg™ Type 17 174.020V5




110Soft Tissue Level PLAN Cassette 048.905

110Soft Tissue Level PLAN Set 048.904

106, 143Solid abutment driver 046.067

106, 143Solid abutment driver 046.068

70SP Profile drill 034.435








155Spacer 048.451V4

155Spare lamella retention insert 048.457

155Spring 048.455V4

71S/SP Tap 034.445

71S/SP Tap 034.645

71S/SP Tap 034.245

78S/SP Tap 044.579

76S/SP Tap 044.577

74S/SP Tap 044.575

151Stabilization pin for retaining gold copings in solder investment 048.208V4

37Standard implant 033.432G


37Standard implant 033.432S

































INDEX

278

ALPHABETICAL INDEX


















45Standard Plus implant 033.452G


45Standard Plus implant 033.452S

















































INDEX

279

ALPHABETICAL INDEX








42Standard Plus Implant 033.417S




30Standard, Standard Plus and Tapered Effect implant distance indicator 046.148

28Stepped drill 034.060

28Stepped drill 034.061

31Stepped pin 049.818V4

69Stop key 034.006

105Storage system 041.501

96Storage system 041.500

22Straumann® Bone Block Fixation 041.032

244Straumann® Bone Level Implant 120.0033

21Straumann® BoneCeramic 400–700 070.203



118, 181Straumann® CARES® Wax-up kit 019.0063

118, 181Straumann® CARES® Wax-up kit for Camlog® 019.0050

118, 181Straumann® CARES® Wax-up kit for NobelReplace™ 019.0051

20Straumann® Emdogain 0.3 ml 075.101




20Straumann® Emdogain PLUS 075.117

27Straumann® gonyX™ 019.0201

20Straumann® PrefGel 0.6 ml 075.203

244Straumann® Standard Plus (NN) Implant 140.019

244Straumann® Standard Plus NNC Implant 140.122

96Straumann® Surgical cassette 040.165

244Straumann® Tapered Effect Implant 140.062

73Surgical cassette 034.001

91Surgical instruments starter set, Ø 4.1 mm for preparation by hand 040.320

91Surgical instruments starter set, Ø 4.1 mm, Tap for adapter, for preparation using the handpiece, 040.330

92Surgical instruments starter set, Ø 4.8 mm, for preparation by hand 040.321

92Surgical instruments starter set, Ø 4.8 mm, Tap for adapter, for preparation using the handpiece 040.331

116, 117, 125, 127synOcta® basal screw 048.356

107, 126, 135synOcta® Guide pin 046.241

107, 136synOcta® Guide pin 046.247

244synOcta® system 140.024

73T -sleeve 034.053V4

73T-sleeve 034.055V4

132Tap 044.570

51Tapered Effect implant 033.752S



















INDEX

280

ALPHABETICAL INDEX







52Tapered Effect implant 033.762G





70TE Profile drill 034.237








64TempImplant 80372SV4

64TempImplant 80371SV4

64TempImplant bending tool 80356

64TempImplant inserting device 80363

64TempImplant inserting device 80398

72Template fixation pin 034.255




28templiX reference plate 034.062-03

155Threaded mounting ring 048.454V4

152, 217, 228Titanium bar 048.465

152, 217, 228Titanium bar 048.466

152, 153, 217, 218, 228,229

Titanium bar matrix 048.470

152, 153, 217, 218, 228,229

Titanium bar matrix 048.471

155Titanium matrix 048.450

156Titanmagnetics® denture magnet 048.515

156Titanmagnetics® impression coping 048.014

156Titanmagnetics® insert (abutment) 048.511

156Titanmagnetics® Insert applicator (driver) 046.146

156Titanmagnetics® model implant 048.121

94, 107Torque control device 046.049

240TPS occlusal screw 048.312C

129Transfer aid 048.059V4





137Transfer aid 048.032

64, 155Transfer pin 048.109

132Transversal screw 049.154

104Tray 041.211

240TS gold coping for Octa 048.232C

132TS Hexagonal screwdriver 046.420

240TS post for Octa 048.448C

94Tweezers 046.057

94Tweezers 046.095

69Twist drill PRO 034.626









75, 77, 81, 83, 87, 89Twist drill PRO 044.250

INDEX

281

ALPHABETICAL INDEX


75, 77, 81, 83, 87, 89Twist drill PRO 044.251

77, 83, 89Twist drill PRO 044.254

77, 83, 89Twist drill PRO 044.255

96U ltrasonic cleaning cassette 040.175

245Upper jaw 140.033

93WN Bone profile drill 044.305

40, 48, 53WN Closure screw 048.375

40, 48, 53WN Healing cap 048.030

40, 48, 53WN Healing cap 048.038

40, 48, 53WN Healing cap 048.039

40, 48, 53WN Healing cap 048.053

133, 146WN Impression cap 048.013

165WN LOCATOR® Abutment 048.184





112WN PLAN LOCATOR® Abutment 048.283V4





112WN PLAN Solid abutment 6° 048.938V4

112WN PLAN Solid abutment 6° 048.939V4

147WN Protective cap 048.051

147WN Protective cap 048.052

117, 133WN Repositionable implant analog 048.172

117WN Scanbody 048.086V4

146WN Solid abutment 6° 048.545

146WN Solid abutment 6° 048.546

146WN Solid All-in-One Set 040.745




117WN Straumann® CARES® Mono Scanbody 048.169

117WN Straumann® Scanbody 048.069

137WN synOcta® 15° angled abutment 048.608

137WN synOcta® 15° angled abutment 048.609

111WN synOcta® 15° angled PLAN abutment 048.933V4

111WN synOcta® 15° angled PLAN abutment 048.934V4

111WN synOcta® 1.5 PLAN abutment 048.931V4

134WN synOcta® 1.5 screw-retained abutment 048.603

133WN synOcta® analog 048.171

136WN synOcta® cementable abutment 048.606

111WN synOcta® Cementable PLAN abutment 048.932V4

134WN synOcta® Gold abutment 048.644

134WN synOcta® Gold coping 048.639

134WN synOcta® Gold coping 048.638

133WN synOcta® impression cap 048.091

134WN synOcta® Meso milling cylinder 048.573

134WN synOcta® Plastic coping 048.666




133WN synOcta® positioning cylinder 048.095

133WN synOcta® Post 048.234

133WN synOcta® Post 048.233

147WN Temporary coping 048.657

147WN Temporary coping 048.656

117WN Wax-up sleeve 048.089

30X -ray reference sphere 049.076V4

30X-ray templates 150.215



Valid from January 1, 2012, until publication of the new catalog.

TrademarksCamlog® is a brand used by Camlog Technologies AG, Germany.Ceramicor®, Elitor® and Esteticor® are registered trademarks of Cendres & Métaux SA, Biel-Bienne (Switzerland).Cronidur® 30 is a registered trademark of Energietechnik Essen GmbH, Germany.The Dalbo®-Rotex® Matrix is a registered trademark of Cendres & Métaux SA, Biel-Bienne (Switzerland).Dolder® is a registered trademark from Prof. Eugen Dolder, former director, School of Dentistry of Zurich.IPS e.max® is a registered trademark of Ivoclar Vivadent AG, Liechtenstein.LOCATOR® is a registered trademark of Zest Anchors, Inc., USA.NobelReplace™ is a trademark of the Nobel Biocare Group.NSK® is a registered trademark of NAKANISHI INC., Japan.Osstell™ and Smartpeg™ are trademarks of Osstell AB. Sirona® is a registered trademark of Sirona Dental Systems GmbH, Germany.Splitex® is a registered trademark of Amann Girrbach GmbH, Germany.steco® and Titanmagnetics® are trademarks of steco-system-technik GmbH & Co. KG, Germany.

www.s t raumann.com

© Institut Straumann AG, 2012. All rights reserved. Straumann® and/or other trademarks and logos from Straumann® mentioned herein are the trademarks or registered trademarks of Straumann Holding AG and/or its affiliates. All rights reserved. St

raum

ann

prod

ucts

are

CE

mar

ked

1

1/11

15

2.20

0/en

BH21

111

International HeadquartersInstitut Straumann AG Peter Merian-Weg 12CH-4002 Basel, SwitzerlandPhone +41 (0)61 965 11 11Fax +41 (0)61 965 11 01

odonta.org en.pdf · -04 pack of 4 abs acrylonitrile butadiene styrene al aluminum bl bone level...

Documents