Electrostatic precipitator modeling and simulationKejie Fang Longhua MaInstitute of Industrial ControlZhejiang University

Introduction Research and design in ESP Simulation results and analysis ConclusionOUTLINE OF PRESENTATION

INTRODUCTION Nowadays, the environment protection has become a crucial problem and the authorities are requested to set increasingly more stringent limits , one of which is the emissions from the industrial plants of solid particulate and other gaseous pollutants.1. Background

2. ABOUT ELECTROSTATIC PRECIPITATOR Electrostatic precipitator (ESP) is a widely used device in so many different domains to remove the pollutant particulates, especially in industrial plants. 2.1 What is ESP Introduction

2.2 HOW ESP WORKS Generally, the processes of electrostatic precipitator are known as three main stages: particle charging, transport and collection. 2.2.1 Main process of ESP Introduction

To characterize all these stages determines to take a great number of basic phenomena into account from a physical point of view when they occurred. IntroductionThese are stages interacted that originated from the complexity of the processes of precipitator.

Schematic of wire-plate ESPFig.1 Schematic of wire-plate electrostatic precipitator Introduction

Mechanism of ESPFig. 2 Mechanism of electrostatic precipitator Introduction

2.2.2 PROCESS OF Particle charging Particle charging is the first and foremost beginning in processes. IntroductionAs the voltage applied on precipitator reach threshold value, the space inside divided into ionization region and drift region.

The electric field magnitude around the negative electrode is so strong that the electrons escape from molecule.Under the influence of electric field, the positive ions move towards the corona, while the negative ions and electrons towards the collecting plates. Introduction

2.2.3 Particle transport In the moving way, under the influence of electric field, negative ions cohere and charge the particles, make the particles be forced towards collecting-plate as well as Fig.2 shows. Introduction

2.2.4 Particle collection As soon as the particles reach the plate, they will be neutralized and packed by the succeeded ones subsequently. The continuous process happens, as a result, particles are collected on the collecting plate. Introduction

Research and design in ESP modeling The numerical model describes in time and space the relevant processes that are involved in transport, charging, migration and collection of fly ash. To represent the complete processes, the model is therefore structured into several modules.

The model here is organized into the following three sections: electric field and discharge processes particle charging particle collection

3.1 electric field and discharge processes The particle collection in electrostatic precipitators is largely dominated by the distribution of the electric field in the interelectrodic space.

In the absence of particles, neglecting the transport gas velocity and by assuming that the magnetic field due to the corona current is negligibly small. Electronical conditions are described by next three equations :

(1)(2)(3)

Here, we adopt equations (4) (5) (6) to describe the electric field distribution with the initial and boundary conditions.

V( x, y) means the electric potential of the position (x, y), V0 is the initial potential on the wire, Sx is distance between collecting plate and wire, Sy is half length of the two nearest wires ,a is the radius of particle, when x, y means the coordinates direction, shown as Fig.3.

Fig. 3 Sketch of precipitator geometry and computed grid

(5)(6) and V0 mean the charge density and electric potential at the position as Fig.3 shown.

3.2 particle chargingThe field charging refers to the local distorsion caused near the particle surface by the difference in dielectric constants. This process continues until the particle goes up to the saturation charge, which produces an electric field on particle surface equal and opposite to the external field.

Equation (7) is chosen to describe the model of particle charging :(7)Where is the relative dielectric constant and E0 is the external field, qs and R are the particle charge and radius.

3.3 particle collectionThis module simulates in detail the boundary layer near the collecting plates and the interchange that take place.Here, we choose equation (8) to describe particle collection .

(8)C is the particle density, C0 is the entry density of particle, a is the unit collecting area in the flow way, f is area of ESP cross section, when w means particle velocity towards plate and v is the velocity moving to outlet.

4 Simulation results and analysis According the above analysis of the mechanism and modeling of ESP, we design a simple ESP simulation platform which is based on Scilab .

Fig.4 Simulation Platform

Fig.5 Input Interface

Fig.6 Distribution of electric field ExSimulation of electric field

we can find that around the wires, Ex get a largest value, when at the connecting way of two wires, Ex is no more than zero. The cause of this distribution is the potential, at the connecting way of wires, nearly zero. Ex is decreased regularly from the wire at the coordinate line x, but larger when close to the collecting plate.

Fig.7 Distribution of electric field EySimulation of electric field

Fig.8 Particle density distribution in ESP Simulation of particles density distribution

From Fig.8, we see the particles density distribution obviously. The density reaches the largest value at the entry of the ESP under the influence of electric wind. The value of density gets smallest near the wire at the direction to collecting plate.

Simulation of deposit density Fig.9 Distribution of deposit density

Fig.9 shows us the deposit density, along the collecting plate deposit density is decreased definitely, since as time go on, the particle is collected by the plate continuously. So at the later part, the deposit density is lower, and reasonable.

CONCLUSION we construct a numerical model of electrostatic precipitator and design base on Scilab. The simulation results of these processes are according with laboratory experimental tests to obtain physical information and useful validations.

The EndThanks