

of 5

Section 4 – Land Owner Solicitor Details

Company Name:

Address:

Contact Name:


Email Address:

Section 5 – Proposed Connection Load Details

Plot Number or Name

Quantity Supply Capacity (kVA) LV

HV Build Phase Per Plot* Total 1Ph 3Ph

Total Load:

*ADMD (After Diversity Maximum Demand)

As a guide for gas heated semi‐detached domestic housing use 1.0 kVA per plot (up to 3 bedrooms) and for detached domestic housing use 1.4 kVA per plot (up to 5 bedrooms).

As a guide for electric heated domestic apartments/housing use 3.4 kVA per plot (up to 2 bedrooms and within a high density of units). For electric heated housing with ‘restricted hours tariffs and all other scenarios please refer to UKPD for guidance.

For electric heated domestic apartments use UKPD ADMD Ready Reckoner to calculate the rating of distribution transformers.

Section 6 – Proposed Generation and Export Details

Maximum power output (phased if appropriate):

Generation set specification type e.g. PV, CHP:

Confirmation of plans to export back to network:

Plans to run in parallel e.g. test back‐up generator:

Completed ENA document e.g. G59, G83:



of 5

Section 7 – Proposed Materials and Equipment for Adoption

Category Description Specification Supplier

Note: If you need to provide any further materials and equipment details please provide on a separate sheet in the above format



of 5

Section 8 – Other drawings and documents to be provided as indicated

Please include the information below depending on the type of projects listed on the right.

LV Networks

LV supplies from a

new

standard sub‐

station

LV supplies from a

new

non‐standard

sub‐station

HV M

etered

Supply

1 Site plan to include the following minimum information: ‐

Clearly defined site boundary

North point

Site location detail (can be provided on separate drawing if desired)

Minimum scale 1:500 @ A3

Yes Yes Yes Yes

2 LV design drawing to include the following minimum information: ‐

Size/type and network asset owner of existing cable at the point of connection

Link box and fuse sizes where required

Substation location where required

Proposed LV cable size/type and ducting size/type where required

All joints, pot ends, terminations and earthing

Detailed cross sections along the cable route

Service load, termination, service fuse size, CT ratio and metering arrangements for each supply

Kiosk/cabinet details, where required, including manufacturers specification

For apartments include details of internal mains and service routes, cable ways, containment, multi metering layouts, distribution boards, fusing and service positions

Street lighting connections where required

Single line diagram (can be provided on separate drawing if desired)

North point


Yes Yes Yes N/A

3 HV design drawing to include the following minimum information: ‐

Size/type and network asset owner of existing cable at the point of connection

Substation location, load and plant specification including manufacturers details

Small power and lighting specification and details

Proposed HV cable size/type and ducting size/type where required

All joints and terminations

Detailed cross sections along the cable route

Customers transformer or HV network details for any HV metered supplies

Emergency trip button and HV meter panel details where required

Kiosk/cabinet details, where required, including manufacturers specification

Single line diagram (can be provided on separate drawing if desired)

HV Protection details and settings

Ancillaries: Tripping battery, automation details, where required

North point


N/A Yes Yes Yes

4 Substation earthing drawing to include the following minimum information: ‐

Substation layout

Earthing design

N/A Yes Yes Yes



of 5

Section 9 – Additional information/comments

Section 10 – ICP Declaration

I confirm that by submitting this application we have been appointed as an ICP to design and install electrical networks to the above named development. I understand that failure to supply any of the required information may result in a delay in my application being processed.

ICP Company Name:

Print Name:

Signature:

Date:

UKPD exist to provide customers with a forward thinking, flexible and least hassle approach in the area of adoption of electricity distribution networks, which we will look to deliver through pioneering commercial solutions and the introduction of a more pragmatic and streamlined approach to the whole adoption process. Contact Us: Address: Head Office, 6500 Daresbury Park, Warrington, Cheshire, WA4 4GE Phone number: 0844 74 000 74 E‐mail: [email protected] We are open: Main office is open from 8.30am to 5pm Monday to Friday

5 Substation with standard housing drawing to include the following minimum information: ‐

GRP specification and manufacturer or brick built housing specification

Plinth construction details

N/A Yes N/A Yes

6 Substation with non‐standard housing drawing to include the following minimum information: ‐

Architect proposals for substation room

Substation layout including dimensions, doors, joint locking arrangement and ventilation details

N/A N/A Yes Yes

7 IDNO legal drawing to include the following minimum information: ‐

Substation access

Cable easements

Street names

North point

Scale 1:1250 with insert at 1:500 to highlight any substation detail

Yes Yes Yes Yes

8 Volt drop and earth loop impedance calculations for LV network Yes Yes Yes N/A

9 Drawing register confirming the following:‐

Drawing numbers and revision details

Drawing title

Scheme title

Yes Yes Yes Yes

electric network design approval application

Documents