drawing and annotating the joints using the isometric drawing techniques
TRANSCRIPT
![Page 1: Drawing and annotating the joints using the isometric drawing techniques](https://reader038.vdocuments.site/reader038/viewer/2022100519/56649cf75503460f949c7b2e/html5/thumbnails/1.jpg)
Drawing and annotating the joints using the isometric drawing techniques
![Page 2: Drawing and annotating the joints using the isometric drawing techniques](https://reader038.vdocuments.site/reader038/viewer/2022100519/56649cf75503460f949c7b2e/html5/thumbnails/2.jpg)
Mark out and cut a Lap Joint
Start Here – Lap joint
![Page 3: Drawing and annotating the joints using the isometric drawing techniques](https://reader038.vdocuments.site/reader038/viewer/2022100519/56649cf75503460f949c7b2e/html5/thumbnails/3.jpg)
Mark out and cut a Lap Joint
Mark a waste line around the end of one piecePencil / Try Square
![Page 4: Drawing and annotating the joints using the isometric drawing techniques](https://reader038.vdocuments.site/reader038/viewer/2022100519/56649cf75503460f949c7b2e/html5/thumbnails/4.jpg)
Mark out and cut a Lap Joint
Mark a joint width line - the thickness of the wood from the waste line -
around the piecePencil / Try Square
![Page 5: Drawing and annotating the joints using the isometric drawing techniques](https://reader038.vdocuments.site/reader038/viewer/2022100519/56649cf75503460f949c7b2e/html5/thumbnails/5.jpg)
Mark out and cut a Lap Joint
Using a Marking Gauge mark a line half the thickness of the wood around the end -
from joint line to joint line.
Mark the waste which is to be cut away
![Page 6: Drawing and annotating the joints using the isometric drawing techniques](https://reader038.vdocuments.site/reader038/viewer/2022100519/56649cf75503460f949c7b2e/html5/thumbnails/6.jpg)
Mark out and cut a Lap Joint
Place the work on a Bench Hook
Cut carefully - on the waste side of the line - down to the half way mark using a Tenon Saw
![Page 7: Drawing and annotating the joints using the isometric drawing techniques](https://reader038.vdocuments.site/reader038/viewer/2022100519/56649cf75503460f949c7b2e/html5/thumbnails/7.jpg)
Mark out and cut a Lap Joint
Clamp the work firmly in a Woodwork Vice in an upright position.
Using a Chisel and Mallet gradually remove the waste.
![Page 8: Drawing and annotating the joints using the isometric drawing techniques](https://reader038.vdocuments.site/reader038/viewer/2022100519/56649cf75503460f949c7b2e/html5/thumbnails/8.jpg)
Mark out and cut a Lap Joint
Mark a waste line all around the second piece
Pencil / Try Square
Mark the waste which is to be cut away
![Page 9: Drawing and annotating the joints using the isometric drawing techniques](https://reader038.vdocuments.site/reader038/viewer/2022100519/56649cf75503460f949c7b2e/html5/thumbnails/9.jpg)
Mark out and cut a Lap Joint
Using a Disc Sander or an End Trimmer remove the waste to make the end of the
piece square
![Page 10: Drawing and annotating the joints using the isometric drawing techniques](https://reader038.vdocuments.site/reader038/viewer/2022100519/56649cf75503460f949c7b2e/html5/thumbnails/10.jpg)
Mark out and cut a Lap Joint
Leave the waste tail on the joint and glue the pieces together using PVA
glue
When the glue is dry remove the waste using a Tenon Saw and clean
the joint with Glasspaper
![Page 11: Drawing and annotating the joints using the isometric drawing techniques](https://reader038.vdocuments.site/reader038/viewer/2022100519/56649cf75503460f949c7b2e/html5/thumbnails/11.jpg)
Mark out and cut a Mitre joint
Start Here - mitre
![Page 12: Drawing and annotating the joints using the isometric drawing techniques](https://reader038.vdocuments.site/reader038/viewer/2022100519/56649cf75503460f949c7b2e/html5/thumbnails/12.jpg)
Mark out and cut a Mitre Joint
Measure and mark out the JOINT line all the way around both pieces
Pencil / Try Square
It is more than likely that these will be different distances from the end
![Page 13: Drawing and annotating the joints using the isometric drawing techniques](https://reader038.vdocuments.site/reader038/viewer/2022100519/56649cf75503460f949c7b2e/html5/thumbnails/13.jpg)
Mark out and cut a Mitre Joint
On both pieces mark the wood thickness from the joint line and mark the waste line all the way around
Pencil / Try Square
![Page 14: Drawing and annotating the joints using the isometric drawing techniques](https://reader038.vdocuments.site/reader038/viewer/2022100519/56649cf75503460f949c7b2e/html5/thumbnails/14.jpg)
Mark out and cut a Mitre Joint
Place the INSIDE faces of the joint together and mark the joint direction line
from the middleUPWARDS and OUTWARDS
Pencil / Ruler
![Page 15: Drawing and annotating the joints using the isometric drawing techniques](https://reader038.vdocuments.site/reader038/viewer/2022100519/56649cf75503460f949c7b2e/html5/thumbnails/15.jpg)
Mark out and cut a Mitre Joint
Mark the waste to be cut away on both piecesPencil
![Page 16: Drawing and annotating the joints using the isometric drawing techniques](https://reader038.vdocuments.site/reader038/viewer/2022100519/56649cf75503460f949c7b2e/html5/thumbnails/16.jpg)
Mark out and cut a Mitre Joint
On the WASTE SIDE of the line cut the waste material away
Mitre Saw
![Page 17: Drawing and annotating the joints using the isometric drawing techniques](https://reader038.vdocuments.site/reader038/viewer/2022100519/56649cf75503460f949c7b2e/html5/thumbnails/17.jpg)
Mark out and cut a Mitre Joint
Trim the joint back to the joint lineEnd Trimmer
![Page 18: Drawing and annotating the joints using the isometric drawing techniques](https://reader038.vdocuments.site/reader038/viewer/2022100519/56649cf75503460f949c7b2e/html5/thumbnails/18.jpg)
Mark out and cut a Mitre Joint
Glue the joint togetherPVA Glue / Frame Clamp