![Page 1: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/1.jpg)
1
Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto
Institute for Cosmic Ray Research (ICRR)the University of Tokyo
KAGRA face to face meeting Hongo campus, The University of Tokyo, Tokyo, Japan
6 February 2015
Cryo-payload design
![Page 2: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/2.jpg)
2
Contribution
K. Yamamoto, A. Khalaidovski, T. Miyamoto, Y. Sakakibara, H. Tanaka, T. Uchiyama, T. AkutsuA, S. ZeidlerA, A. HagiwaraB,
N. KimuraB, R. KumarB, T. KumeB, S. KoikeB, I. MurakamiB, T. SuzukiB, S. TerashimaB, T. TomaruB, K. ToyodaB, D. ChenC,
R. DeSalvoD, E. MajoranaE, L. NaticchioniE, W. JohnsonF, K. CraigG, A. CummingG, R. DouglasG, G. HammondG ,
K. HaughianG, I. MartinG, P. MurrayG, S. RowanG , D. HeinertH, G. HofmannH, J. KommaH, S. KrokerH, R. NawrodtH,
C. SchwarzH, KAGRA collaboration
ICRR.UT, NAOJA, KEKB, Astro.S.UTC, Sannio Univ.D, INFNE, Louisiana State Univ.F , University of
GlasgowG, Friedrich-Schiller-Universitaet JenaH
![Page 3: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/3.jpg)
3
0. Abstract
Although there are many topics, here,Kazuhiro Yamamoto will explain recent progress and status of(1)Design (of prototype) of cryo-payload(2)Fabrication (of prototype) of cryo-payload
Some items of R&D will be reported by young researchers, Dan Chen and two fresh persons, Hiroki Tanaka and Takahiro Miyamoto (Prof. Kajita group).
![Page 4: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/4.jpg)
4
Contents
1.Introduction2.Design of “prototype”3.Fabrication of “prototype”4.R&D items5.Summary
![Page 5: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/5.jpg)
55
1. Introduction
555
3km3km
MozumiY-end Sakonishi
X-end
AtotsuCenter
Vibration isolation system, Cryocooler unit, Cryostat, Cryogenic payload
Schematic view of KAGRA interferometerFour mirrors of arm cavity will be cooled.
Kamioka mine (Underground site)
![Page 6: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/6.jpg)
66
Outline of vibration isolation and cryostat
1. Introduction
A. Hagiwara (KEK) proceeds with CAD design drawing.Here, outline of vibration isolation and cryostat is introduced with her drawing (not final version) .
![Page 7: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/7.jpg)
77
Outline of vibration isolation and cryostat
14 m
1. Introduction
Vacuum ducts
along laser beam
Cryostat(Here is a mirror)
Vibration isolation system(room
temperature)
Clean booth
Design drawing without tunnel and cross section
A. Hagiwara
![Page 8: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/8.jpg)
88
Outline of vibration isolation and cryostat
14 m
1. Introduction
Vacuum ducts
along laser beam
Vibration isolation system
Clean booth
Design drawing with tunnel and cross section
Cryostat(Here is a mirror)
2nd floor
Shaft
A. Hagiwara
![Page 9: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/9.jpg)
9
to Vibration isolationsystem View
ports
Main LASER beam
Cryostat Stainless steel t20mm Diameter 2.6m Height ~3.6m M ~ 10 ton
Cryo- payload
Mirror
1. Introduction Outline of cryostat
Double radiation shield
A. Hagiwara
![Page 10: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/10.jpg)
10
View ports
Main LASER beam
SapphireMirror
1. Introduction Outline inside cryostat
Baffle for wide angle scattered light
to Vibration isolationsystem
A. Hagiwara
Cryo- payload
![Page 11: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/11.jpg)
11
Two kinds of full size prototypes for development
11
2. Design of “prototype”
Those are our important next step !
(1)Sapphire lop-eared suspension A part of cryo-payload Main sapphire mirrors are included. All parts are made from sapphire.
(2)Cryo-payload with dummy sapphire suspension This is almost same as the actual cryo-payload. Parts of “sapphire” suspension is a dummy (made from metal).
![Page 12: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/12.jpg)
One of the most importantparts of KAGRA : Main sapphire mirrorsare included.
All parts are made from sapphire.Mainly, D. Chen proceeds with investigation.Details appear on the next Tuesday (10th of Feb) in ELiTES meeting (40 min his talk !). 121212
D. Chen
2. Design of “prototype” (1)Sapphire lop-eared suspension
![Page 13: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/13.jpg)
13A. Hagiwara
EarNail head of fiber
Fiber with nail head on both ends
Blade spring(compensation of fiber length difference)
Mirror
Flat cut
2. Design of “prototype” (1)Sapphire lop-eared suspension
![Page 14: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/14.jpg)
141414
Hydroxide Catalysis BondingD. Chen
fiber break
2. Design of “prototype” (1)Sapphire lop-eared suspension
Bonding between sapphire parts
![Page 15: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/15.jpg)
(2)Cryo-payload with dummy sapphire suspension
1515151515
Pulse tube cryocoolers
Pulse tube cryocoolers
Sapphire suspension
Sapphire mirror (About 20K)
Sapphire fiber
2. Design of “prototype”
Schematic view of cryo-payload
Cryo-payload
![Page 16: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/16.jpg)
(2)Cryo-payload with dummy sapphire suspension
1616161616
Pulse tube cryocoolers
Pulse tube cryocoolers
Heat link (pure Al)
Sapphire mirror (About 20K)
Sapphire fiber
2. Design of “prototype”
Schematic view of cryo-payload
![Page 17: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/17.jpg)
1717
Latest (not final) CAD designdrawings by A. Hagiwara
17A. Hagiwara
Mirror
Platform (with vertical spring)
2. Design of “prototype” (2)Cryo-payload with dummy sapphire suspension
![Page 18: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/18.jpg)
181818
Mirror
Recoil mass
“Two” intermediate massesUpper part includes angle adjustment system.
A. Hagiwara wrote CAD design drawing of these parts !
2. Design of “prototype” (2)Cryo-payload with dummy sapphire suspension
A. Hagiwara
Lower part is simple for high Q of sapphire suspension.
![Page 19: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/19.jpg)
1919
Still many items have no CAD design drawings ….
(a)Platform (Vertical metal spring)Investigation of CuBefor this spring is in progress at KEK (T. Tomaru et al.).
(b)Recoil mass for intermediate mass
19
2. Design of “prototype” (2)Cryo-payload with dummy sapphire suspension
A. Hagiwara
![Page 20: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/20.jpg)
Still many items have no CAD design drawings ….
(c)Local sensor and actuator to adjust angle and positionCryogenic test is necessary(T. Miyamoto).
(Short and long optical leversare also adopted)
202020
2. Design of “prototype”
A. Hagiwara
(2)Cryo-payload with dummy sapphire suspension
![Page 21: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/21.jpg)
Still many items have no CAD design drawings ….
(d)Heat links to cool payload (and extra pendulum for vibration isolation)
(e)Baffle (and suspension)
212121A. Hagiwara
2. Design of “prototype” (2)Cryo-payload with dummy sapphire suspension
![Page 22: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/22.jpg)
2222
Fabrication for prototypes must be in progress !
(1)Sapphire lop-eared suspension All sapphire parts will be delivered by end of next March.
(2)Cryo-payload with dummy sapphire suspension (Dummy) mirror, recoil mass, and intermediate mass will be delivered by end of next March.
3. Fabrication of “prototype”
![Page 23: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/23.jpg)
23A. Hagiwara
2 ears
4 fibers4 blade springs
1 sapphire bulk
2 Flat cuts
(1)Sapphire lop-eared suspension
3. Fabrication of “prototype”
![Page 24: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/24.jpg)
242424242424
Processing of two flat cut on barrel surface ARD-OPTICS Ltd (Armenia) , Partner of IMPEX (Germany) E-mail from Dr. Ruben Babasyan (3 Feb. 2015) “We are polishing the second face.”
Dummy bulk (Shinkosha)
3. Fabrication of “prototype” (1)Sapphire lop-eared suspension
205 mm
164 mm in thickness
![Page 25: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/25.jpg)
252525252525
Processing of two flat cut on barrel surface ARD-OPTICS Ltd (Armenia)
The first surface !
3. Fabrication of “prototype” (1)Sapphire lop-eared suspension
![Page 26: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/26.jpg)
262626262626
Two ears ARD-OPTICS Ltd (Armenia) , Partner of IMPEX (Germany) Photo from Armenia
3. Fabrication of “prototype” (1)Sapphire lop-eared suspension
![Page 27: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/27.jpg)
272727272727
Four sapphire fibers with nail heads : IMPEX
E-mail from Dr. Lena Barsukowa (29 Jan. 2015)“The processing of fiber is progressing according to plan till now.”
3. Fabrication of “prototype” (1)Sapphire lop-eared suspension
![Page 28: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/28.jpg)
282828282828
Four blade spring : Shinkosha (Japan)
They have already delivered three pieces and two more pieces will come by the end of March.
Sapphire blade spring
3. Fabrication of “prototype” (1)Sapphire lop-eared suspension
![Page 29: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/29.jpg)
292929292929
Dummy mirror and ears (stainless) Mechanical Engineering Center of KEK has already delivered !
220 mm
150 mm
3. Fabrication of “prototype” (2)Cryo-payload with dummy sapphire suspension
![Page 30: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/30.jpg)
303030303030
Intermediate mass We ordered VIC (http://www.vic-int.co.jp/) and the parts will come by the end of March.
Recoil mass Processing in Mechanical Engineering Center of KEK is in progress.
Mirror
3. Fabrication of “prototype” (2)Cryo-payload with dummy sapphire suspension
![Page 31: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/31.jpg)
313131313131
Three topics from young researchers
(1)Sapphire suspension thermal noise : Dan Chen(2) Sapphire blade spring : Hiroki Tanaka(3) Sensors and motors to adjust tilt angle : Takahiro Miyamoto
4. R&D items
![Page 32: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/32.jpg)
323232323232
(1)Sapphire suspension thermal noise
D. Chen measured mechanical loss of fiber and bonding. Moreover, he derived thermal noise from his measured result using ANSYS.
4. R&D items
![Page 33: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/33.jpg)
333333333333
(2)Sapphire blade spring
33
4. R&D items
Fiber length difference compensationDesign : R. Kumar et al., GWADW2014 (http://www.gravity.ircs.titech.ac.jp/GWADW2014/slide/Rahul_Kumar.pdf)
Shinkosha made such blade springs !
Resonant frequency of vertical mode Measurement : 14.3 Hz, Calculation : 14.4 Hz
Hiroki Tanaka investigated long term (one month) drift with load.
![Page 34: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/34.jpg)
Motor and sensor to adjust angle of mass of payload is necessary.At least, they must work at cryogenic temperautre and in vacuum.
Takahiro Miyamoto is investigating what kinds of sensor and motors are able to work at cryogenic temperature.
343434343434
(3)Sensors and motors to adjust tilt angle
34
4. R&D items
![Page 35: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/35.jpg)
353535353535
(3)Sensors and motors to adjust tilt angle
35
Above black cubic corresponds to a small red box.A screw goes through this cubic. The motor rotates this screw and the black cubic moves along the screw.
4. R&D items
When a small red box was moved by a motor,the center of PF or IM is also moved.Since PF and IM are suspended by a fiber,their angle is changed.
D. Chen
D. Chen
![Page 36: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/36.jpg)
3636
(1)Sapphire suspension thermal noise(Chen)
![Page 37: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/37.jpg)
3737
(1)Sapphire suspension thermal noise(Chen)
![Page 38: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/38.jpg)
3838
(1)Sapphire suspension thermal noise(Chen)
![Page 39: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/39.jpg)
3939
(1)Sapphire suspension thermal noise(Chen)
![Page 40: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/40.jpg)
4040
(1)Sapphire suspension thermal noise(Chen)
![Page 41: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/41.jpg)
4141
(1)Sapphire suspension thermal noise(Chen)
![Page 42: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/42.jpg)
4242
(2)Sapphire blade spring (Tanaka)
![Page 43: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/43.jpg)
4343
(2)Sapphire blade spring (Tanaka)
![Page 44: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/44.jpg)
4444
(3)Sensors and motors to adjust tilt angle (Miyamoto)
Purpose
• The motors and sensors to adjust the angle of masses of cryogenic payload are inevitable for operation of detector. They should work at cryogenic temperature(and in vacuum).
• I am performing operation examinations for candidates of motors and sensors at cryogenic temperature (in vacuum).
![Page 45: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/45.jpg)
4545
Motor test(Miyamoto)
Stepping motor(ORIENT MOTOR MODEL PK525A) State of the test(~20K)
Al Mass~100g
I tested the motor which is no compatible with low temperature (and vacuums). Therefor, I removed oil used inside the motor.
The movement of the mass can be observed.
Direction of motion
![Page 46: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/46.jpg)
Sensor test (Miyamamoto)Since our motor can move the mass at cryogenic temperature. We will use it for the sensor cryogenic test.We will check whether the sensor can monitor the motion of Al mass by motor.
I am preparing test of Light reflection displacement sensor.
Light from LED is reflected by target and goes to photodiode(PD). The light intensity depend on D. Thus we can derive D from output of PD.
D
![Page 47: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/47.jpg)
4747
ELiTES: ET-LCGT interferometric Telescope Exchange of Scientists Grant for collaboration about cryogenic between KAGRA and ET.
Ettore Majorana reports in this afternoon.Kazuhiro Yamamoto will report on the next Monday (9th of Feb) in 3rd ELiTES meeting.
ELiTES
![Page 48: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/48.jpg)
48
5. SummaryTwo kinds of full size prototypes (1)Sapphire lop-eared suspension (2)Cryo-payload with dummy sapphire suspension
Design and fabrication of prototypes (1)Sapphire lop-eared suspension : All sapphire parts will be delivered by the end of March. (2)Cryo-payload with dummy sapphire suspension Dummy mass, recoil mass, intermediate mass were or will be delivered by the end of March. However, still many parts must be designed.
![Page 49: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/49.jpg)
49
5. SummaryR&D items (1)Sapphire suspension thermal noise : Dan Chen measured mechanical loss of fiber and bonding. Evaluated thermal noise is enough small. (2)Sapphire blade spring : Hiroki Tanaka observed the displacement with load in one month. This spring survived !
(3)Sensors and motors to adjust tilt angle Takahiro Miyamoto confirmed a motor (ORIENT MOTOR MODEL PK525A) works at cryogenic temperature. He adopts this motor to check how cooled light reflection displacement sensor works.
![Page 50: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/50.jpg)
50
Thank you for your attention !
![Page 51: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/51.jpg)
515151515151
Cryogenic payload Dummy mirror and ears (stainless)
3. Payload
S. Koike
![Page 52: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/52.jpg)
525252525252
Cryogenic payload Dummy mirror and ears (stainless)
3. Payload
S. Koike
![Page 53: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/53.jpg)
535353535353
Cryogenic payload Dummy mirror and ears (stainless)
3. Payload
S. Koike
![Page 54: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/54.jpg)
545454545454
![Page 55: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/55.jpg)
555555555555
![Page 56: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/56.jpg)
565656565656
![Page 57: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/57.jpg)
575757575757
![Page 58: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/58.jpg)
585858585858
![Page 59: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/59.jpg)
595959595959
![Page 60: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/60.jpg)
606060606060
![Page 61: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/61.jpg)
61
to SAS
View ports
Remote valve unit
4 Low vibration cryocooler unit
Main LASER beam
Cryostat Stainless steel t20mm Diameter 2.6m Height ~3.6m M ~ 10 ton
Cryo-coolers Pulse tube, 60Hz 0.9 W at 4K (2nd) 36 W at 50K (1st)
Outline of cryostatCryogenic
payload
Mirror
S. Koike
1. Introduction
![Page 62: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/62.jpg)
6262626262
2 Pulse tube cryocoolers
2 Pulse tube cryocoolers
Pulse tube cryocoolers
Baffles Cryo duct(Yusuke’s talk)
Outer shield(80K)
Inner shield(8K)
Vacuum chamber
(300K)
1. Introduction
![Page 63: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/63.jpg)
636363636363
Hole on radiation shield for wire from SAS .Duct to reduce radiation invasion is necessary.
6363636363
2. Cryostat
Baffles Cryo duct(Yusuke’s talk)
![Page 64: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/64.jpg)
646464646464
CuBe blade spring in platform
Intermediate Mass
Intermediate Recoil Mass
Recoil MassTest Mass (sapphire mirror)
Platform includes CuBe spring for vertical vibration isolation.
3. Payload
![Page 65: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/65.jpg)
656565656565
CuBe blade spring in platformLarge CuBe blade spring (provided by VIS group) in 1/4 cryostat in ICRR. They will be moved to KEK on the 8th of Aug.
3. Payload
![Page 66: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/66.jpg)
6666
Some items for future research (not perfect list)
(a)Investigation material properties (Q, thermal conductivity, strength etc.) of coating, fiber and so on.(b)Sapphire bonding, Sapphire fiber clamp(c)Control and damping scheme Actuators and sensors at cryogenic temperature(d) Mechanical and thermal simulation for payload(e) Vertical spring in cryostat(f) Reduction of initial cooling time Thermal resistance of clamp .... (g) Baffles for scattered light in radiation shield(h) Assembly procedure
7. For future
![Page 67: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/67.jpg)
67
2. Issues
(1)How to assemble Details of construction, clean room ….
(2)Strength Tensile strength, development of clamp, sapphire bonding …
(3)Control and damping system to reduce fluctuation and instability Actuators (what and where), resonant mode (frequency and Q) and so on
![Page 68: 1 Kazuhiro Yamamoto, Dan Chen, Hiroki Tanaka, Takahiro Miyamoto Institute for Cosmic Ray Research (ICRR) the University of Tokyo KAGRA face to face meeting](https://reader036.vdocuments.site/reader036/viewer/2022062516/56649d6f5503460f94a505da/html5/thumbnails/68.jpg)
68
2. Issues
(4)Cooling
Temperature of mirror (below 20 K), initial cooling time, heat resistance of clamp …
(5)Noise
Thermal noise, vibration via vibration isolation system and heat links …