door & patch fittings: call: 09 24-1180 - euroglass€¦ · • suitable for use with uroglass...
TRANSCRIPT
door & patch fittings:index
inSTALLATiOn deTAiL C2 - C4
FLOOR SPRinGS C5 - C6
MORiTZ SeLF-CLOSinG PATCH C7
PATCH FiTTinGS C8 - C11
diGiLOCK C12
PATCH LOCKS C13 - C15
dOOR RAiLS C16 - C17
ViennA HYdRAULiC HinGe C18
CHAnneL C19
C1
CALL: (09) 624-1180www.euroglass.co.nz
catalogue effective 1st JuNe 2015
door & patch fittings:inSTALLATiOn
C2
CALL: (09) 624-1180www.euroglass.co.nz
iNstallatioN DimeNsioNs
dimensions:x = 7mmY = 3mmZ = 4mm
x
Y Z
Y
YA B C
type a - Full width rails fitted along top and bottom edges
A1 A2 A3 A4 A5 A6
type B - Full width rails fitted along bottom edge only, patch fitted at top corner
B1 B2 B3 B4 B5 B6 B7 B8
B9 B10 B11 B12 B13
type c - Patches fitted at top and bottom corners
C1 C2 C3 C4 C5 C6 C7 C8
C9 C10 C11 C12 C13
door & patch fittings:inSTALLATiOn
glassAll glass used in frameless glass door assemblies must be approved toughened float safety glass.
DoorsRecommended maximum sizes:
Max door height (mm - overall)
Max width(mm)
internal
external
Wind zone
Low Med High Very high
10mmpatch 1000 2400 2200 2000 1800
n/Arail 1100 2570 2370 2170 1970
12mmpatch 1100 2800 2600 2400 2200 2000
rail 1200 2970 2770 2570 2370 2170
15mm rail 1300 3600 3400 3200 2800 2400
19mm rail Specific design required
lockiNgRails and Patch Fittings are supplied with a Lockwood 590 series lock which enables the doors to be part of a similar master key system if so required, and is available in the following combinations: - key lock both sides - key lock one side only - key lock one side, turn knob on other side
siDe paNelsMaximum available toughened size available from new Zealand manufacture for 10 or 12 mm glass thickness is 4.5m x 2.44m
fiNsStabilising fins are necessary to cope with loads imposed on a door assembly by the action of the door and external wind loads. The fins must be securely fixed to a rigid structure at the top of the assembly.
10mm glassWhen the width of the side panel A plus the height of the over panel B exceeds a total of 1.2m, a fin is required, but not necessary if A or B are less than 400mm.
12mm glassWhen the width of the side panel A plus the height of the over panel B exceeds a total of 1.5m, a fin is required, but not necessary if A or B are less than 500mm.
C3
CALL: (09) 624-1180www.euroglass.co.nz
B
a
door & patch fittings:inSTALLATiOn
typical Door applicatioN:
C4
CALL: (09) 624-1180www.euroglass.co.nz
hpt20
cpK590 or EL10cpK
hpt10pL590 or EL10
LK590Efs840
fLoor spring
cpL590 or EL10cpL
dd300
hpt24 orhpt25 4mm gap
between doors
door & patch fittings:FLOOR SPRinGS
efs840 euroglass floor springavailaBle fiNisHes• Stainless steel (cover plate)
tecHNical Details• double action floorspring including stainless steel cover plate• 2 spring strengths; 16nm (weak), 25nm (standard)• Maximum door weight 100kg• Maximum door width 1100mm on standard spring and 800mm on weak spring• Available 90˚ in hold open, and non-hold open• 2 speed hydraulic control; closing adjustment 130˚-15˚ latching adjustment 15˚-0˚• Spindle heights from STd to 50mm extension (5mm increments)• Suitable for use with euroglass frameless patch fittings and rails• Warranty 5years or 500,000 cycles (whichever first)
overHeaD Door closer• double action• 90˚ hold open• Aluminium / wood fix silver pearl coverplate• Maximum door width: 1000mm
optioNs• non hold open
C5
CALL: (09) 624-1180www.euroglass.co.nz
324mm
130mm
306mm
108mm
55(65) 324
108 130
306
51-58 cover plate
EUROGLASS EFS840
2
* S. T.D. Spindle Clearance 8mm* 5mm Extended Clearance 13mm
108
40
*
EUROGLASSEFS840
door & patch fittings:FLOOR SPRinGS
C6
CALL: (09) 624-1180www.euroglass.co.nz
staNDarD floor spriNg• Low profile 40mm depth• double action• 90˚ hold open• Stainless steel coverplate• Maximum door weight: 100kg• Maximum door width: 1100mm• Maximum opening angle: 130˚• Variable closing force from 25 nm
optioNs• Brass coverplate• non hold open• 5, 10, 15 mm extended spindles• 15nm weak spring force
floor spriNgs
Heavy Duty floor spriNg• double action• Selective multi-point hold open adjustable
between approximately 75˚ and 175˚• Mechanical backcheck at approximately
85˚ and 165˚• Stainless steel coverplate• Maximum door weight: 300kg• Maximum door width: 1400mm• Maximum opening angle: 180˚• Variable closing force 53 nm
optioNs• Brass coverplate• 5, 10, 15 mm extended spindles• 35nm spring force
55(65) 324
108 130
306
51-58 cover plate
DORMA BTS84
2
.T * S .D. Spindle Clearance 8mm to50mm Extended Clearance 58m m
108
DORMABTS84 40
*
2
55(65) 358
78 105
341
51-58 cover plate
DORMA BTS80
78
DORMABTS80 60
*
* S .T.D. Spindle Clearance 8mm to 50mm Extended Clearance 58m m
epcHo Moritz self-closing patch, hold open eocNHo Moritz self-closing patch, non-hold open
availaBle fiNisHes • Polished stainless steel • Satin stainless steel• Selected powdercoat (lead time applies)
tecHNical DetailsCan be mounted to timber, steel or concreteSuits 8mm, 10mm or 12mm toughened safety glassincludes base pivot plateHold or non-hold open optionsApplicable for door width of 750mm to 1000mm and weight up to 100kgBottom patch fitting for internal doorsUsed in conjunction with a standard top patch fitting and floor stopMultiple adjustments and settings for closing and breaking speedSuitable for single or double doorsResidential and commercial internal use only5 year Warranty
door & patch fittings:MORiTZ SeLF-CLOSinG PATCH FiTTinG
C7
CALL: (09) 624-1180www.euroglass.co.nz
recommended door gaps
glass detail
Base plate hole locations
Max. opening angle 150˚Hold open at 90Non-hold open, by request
Two speed adjustment:Closing speed (150˚ down to 10˚)Breaking speed (10˚ down to 0˚)
door & patch fittings:PATCH FiTTinGS
Hpt10 Bottom patch fitting
availaBle fiNisHes• Polished stainless steel • Satin stainless steel• Selected powdercoat (lead time applies)
tecHNical DetailsBottom patch fittingSuitable for euroglass floorspring range and HPT26 free swing pivotSuits 10mm or 12mm glassAdjustable pivot insertFactory set at 55mm
Hpt20 Top patch fitting
availaBle fiNisHes• Polished stainless steel • Satin stainless steel• Selected powdercoat (lead time applies)
tecHNical DetailsTop patch fittingSuitable for euroglass HPT24, HPT25, HPT34, HPT40 and HPT41 pivotsSuits 10mm or 12mm glassAdjustable pivot insertFactory set at 55mm
Hpt22 Top patch fitting
availaBle fiNisHes• Polished stainless steel • Satin stainless steel• Selected powdercoat (lead time applies)
tecHNical DetailsTop patch fittingSuitable for RTS85 overhead closerSuits 10mm or 12mm glassAdjustable pivot insertFactory set at 55mmReversable to 65mm
C8
CALL: (09) 624-1180www.euroglass.co.nz
31mm
166mm
52mm
31mm
52mm
166mm
166mm
31mm
52mm
HPT22 HPT22
HPT20 HPT20
161
148
6836 37
2055 R 80
161
148
6836
37
20
55R 80
HPT10 HPT10
161
148
6836 37
2055 R 80
door & patch fittings:PATCH FiTTinGS
Hpt24/Hpt25 Top pivot pins
availaBle fiNisHes• Stainless steel for HPT24 • Plated steel for HPT25
tecHNical Details (Hpt24)Plate mounted pinSuitable for use with HPT20 patch and RL2 and RL4 top rails
tecHNical Details (Hpt25)8mm metric thread44mm diameter face washerSuitable for use with HPT20 patch and RL2 and RL4 top rails
Hpt26/Hpt26 eXt5 Floor pivot bearings
availaBle fiNisHes• Polished stainless steel coverplate• Satin stainless steel coverplate
tecHNical DetailsFree swing floor pivotSuitable for use with HPT10 and RL1 and RL3 bottom rails
specialsAvailable with 5mm extended spindle (HPT26exT5)
Hpt28/Hpt28D Head stops
availaBle fiNisHes• Polished stainless steel • Satin stainless steel
tecHNical DetailsRubber infill stopAvailable for single or double door installationsSpecify HPT28S for single door or HPT28d for double door
Hpt30/34 Overpanel pivot patch fitting
availaBle fiNisHes• Polished stainless steel • Satin stainless steel • Selected powdercoat (lead time applies)
tecHNical DetailsFixing overpanel to wall fitted with pivot pinSuitable for use with HPT20Suits 10mm & 12mm glassAdjustable pivot insertFactory set at 55mmHPT30 patch only; HPT34 includes fixing plate
* special Note These sizes are based on a 3mm clearance between
the overpanel and the vertical wall/mullion. Therefore, if overpanel is to fix into a recessed or wall mounted channel, then these sizes must be adjusted to suit
C9
CALL: (09) 624-1180www.euroglass.co.nz
60mm
50mm
22mm
HPT24 HPT25
105mm
28mm
2mm
HPT34
164mm
32mm
15mm
60mm
52mm
HPT26
100mm
4mm
45mm
HPT26exT5
100mm 45mm
4mm
16mm
16mm
100mmHPT28d
50mm
HPT2816mm
16mm
HPT26CPCoverPlate
161
148
6836
37
20
55R 80
door & patch fittings:PATCH FiTTinGS
Hpt40 Overpanel to side panel pivot patch fitting
availaBle fiNisHes• Polished stainless steel • Satin stainless steel • Selected powdercoat (lead time applies)
tecHNical DetailsFixing with pivot pinAdjustable pivot insertSuitable for use with HPT20 & with 10mm or 12mm glass
specialsPivot pin can be removed and replaced with a stop for single action door when this patch fitting is used for an overpanel/side panel
Hpt41l left hand overpanel to side panel pivot patch fitting including fin fitting
availaBle fiNisHes• Polished stainless steel • Satin stainless steel • Selected powdercoat (lead time applies)
tecHNical DetailsPatch fitting for overpanel to side panel with fin at 90˚Suitable for use with HPT20 & with 10mm or 12mm glassAdjustable pivot insert
Hpt41r right hand overpanel to side panel pivot patch fitting including fin fitting
availaBle fiNisHes• Polished stainless steel • Satin stainless steel • Selected powdercoat (lead time applies)
tecHNical DetailsPatch fitting for overpanel to side panel with fin at 90˚Suitable for use with HPT20 & with 10mm or 12mm glassAdjustable pivot insert
C10
CALL: (09) 624-1180www.euroglass.co.nz
161
148
36 R 80
20
55 68
20
37 36
20
73
343
HPT40
HPT41
HPT41
161
148
36 R 80
20
55 68
20
37 36
20
73
343
2020
45 30 10
30
60
R 80
65+
150
20 20
453010
30
60
R 80
65+
150
Looking at outside
Looking at outside
218mm
112mm
31mm
52mm
106mm
52mm
31mm
52mm
156mm
112mm 156mm
31mm
52mm
door & patch fittings:PATCH FiTTinGS
Hpt60 Overpanel to side panel patch fitting
availaBle fiNisHes• Polished stainless steel • Satin stainless steel• Selected powdercoat (lead time applies)
tecHNical DetailsSuits 10mm & 12mm glass
Hpt61 Overpanel to side panel patch fitting
availaBle fiNisHes• Polished stainless steel • Satin stainless steel• Selected powdercoat (lead time applies)
tecHNical DetailsSuits 10mm & 12mm glassincludes removable single action door stop
Hpt70 Overpanel patch fitting incorporating stops for single action double doors
availaBle fiNisHes• Polished stainless steel • Satin stainless steel• Selected powdercoat (lead time applies)
tecHNical DetailsStops removable and reversibleSuits 10mm & 12mm glass
C11
CALL: (09) 624-1180www.euroglass.co.nz
36
20
36
20
73
363
20
34
HPT61
HPT7030
20
30
20
73
HPT6036
20
36
20
73
363
20
34
106mm
106mm
52mm
106mm
106mm
52mm
116mm
52mm
26mm
door & patch fittings:diGiTAL LOCK
yDg313 Digi-lock digital Smart Pad Lock
availaBle fiNisHes• Polished mirrored
tecHNical Detailsnumbered key pad appears on the mirror screen when toucheddual access, either by card or by smart pad touch screen. Multiple cards can be enabledAttahced to the glass using high bond tapesno glass cut out requiredSuitable for 10mm and 12mm glassBattery operated. 4x AA batteries will last up to one year9volt emergency battery back upUsed in conjunction with standard euroglass pivot door fittingsAuto locking (multi featured)For internal and external doors (not suitable for out door use)Residential and commercial applicationsSuits both single and double doorsUsed with keeper box GK313
gk313 Glass Keeper Box
availaBle fiNisHes• Polished mirrored
tecHNical DetailsAttached to the glass using high bond tapesno glass cut out requiredSuitable for 10mm and 12mm glassStriker keeper available for timber or aluminium if required
C12
CALL: (09) 624-1180www.euroglass.co.nz
185mm
75mm
185mm
45mm
Front Face Back of Unit
Front Back
door & patch fittings:PATCH LOCKS
pl590 Bottom or top patch lock
availaBle fiNisHes • Polished stainless steel • Satin stainless steel• Selected powdercoat, lead time applies
tecHNical DetailsComplete with lock and cylindersSpecify cylinder combination e.g. double cylinder, Cylinder/Turn,
Single cylinder & Single turnUse with keeper LK590/GK590Suits 10mm & 12mm glass
cpl590 Centre patch lock
availaBle fiNisHes • Polished stainless steel • Satin stainless steel• Selected powdercoat, lead time applies
tecHNical DetailsComplete with lock and cylindersSpecify cylinder combination e.g. double cylinder, Cylinder/Turn,
Single cylinder & Single turnUse with keepers CPK590 and LK590Suits 10mm & 12mm glass
cpk590 Centre patch keeper
availaBle fiNisHes • Polished stainless steel • Satin stainless steel• Selected powdercoat, lead time applies
tecHNical DetailsUse with CPL590Suits 10mm & 12mm glass
C13
CALL: (09) 624-1180www.euroglass.co.nz
R10
216
42
PL590
PL590
225mm
50mm
37mm
CPL590
37mm
225mm
37mm
225mm
235mm
222
40R10
37mm
50mm
233mm
233mm
50mm
50mm
37mm
37mm
R10
212
R10
40
CPK590
R10
212
R10
40
door & patch fittings:PATCH LOCKS
cpl590p Parrot beak patch
availaBle fiNisHes• Polished stainless steel • Satin stainless steel
tecHNical Details For sliding doorsComplete with lock and cylindersSpecify cylinder combination e.g. double cylinder, Cylinder/Turn,
Single cylinder & Single turnUse with keeper CPK590PSuits 10mm & 12mm glass
cpk590p Parrot beak keeper
availaBle fiNisHes• Polished stainless steel • Satin stainless steel
tecHNical Details
For sliding doorsUse with CPL590PSuits 10mm & 12mm glass
el10pl Top/bottom patch lock
availaBle fiNisHes • Polished stainless steel • Satin stainless steel• Selected powdercoat, lead time applies
tecHNical DetailsVertical bolt projection 20mmeurotype cylinders Specify cylinder combination e.g. double cylinder, cylinder/turn,
single cylinder & single turnSuits 10mm or 12mm glass
el10cpl Centre patch lock
availaBle fiNisHes • Polished stainless steel • Satin stainless steel• Selected powdercoat, lead time applies
tecHNical DetailsVertical bolt projection 20mmeurotype cylinders Specify cylinder combination e.g. double cylinder, cylinder/turn,
single cylinder & single turnSuits 10mm or 12mm glass Striker box is available (code eL10CPK)
C14
CALL: (09) 624-1180www.euroglass.co.nz
R10
203132
R10
43
166mm
31mm
52mm
43
150
R10
eL10K Keeper
eL10PL
eL10PL
eL10CP
CPK590P
CPL590P
WK590P
R10
212
R10
40
R10
212
R10
40
door & patch fittings:PATCH LOCKS
Dc88/ct88 eurostyle cylinders
availaBle fiNisHes• Chrome plate• Satin chrome
tecHNical DetailsUsed with eL10
lk590/gk590 Lockwood 590 groundkeeper
availaBle fiNisHes• Stainless steel (LK590) • Satin silver anodised (GK590)
tecHNical Details (lk590)Used with PL590 and CPL590 locks & rails
tecHNical Details (gk590)Used with rail locks & PL590
sc90/tk90/er90/rs90 Lockwood accessories 590 patch locks
availaBle fiNisHes• Satin silver anodised
tecHNical DetailsUsed with rail locks
374 Straddle fix bolt lock
availaBle fiNisHes• Satin silver anodised• Selected powdercoat (lead time applies)
tecHNical DetailsSuitable for 10mm or 12mm thick glassno cut out of glass panel requiredSilicon fixingTubular groundkeeper includedSlide and glue-on options
C15
CALL: (09) 624-1180www.euroglass.co.nz
Slide option
50mm
28mm40mm
15mm
Glue-on option
12mm
4mm
SC90Single cylinder
TK90Turn knob
eR90escutcheon rose
RS90Retaining screw
GK590
142mm
42mm
28mm
LK59026mm120mm
gK590
dC88Cylinder double
CT88Cylinder/Turn
door & patch fittings:dOOR RAiLS
rl1/rl2/rl2 coc Bottom and top non-locking door rails
availaBle fiNisHes• Satin silver anodised • Polished stainless steel • Satin stainless steel• Selected powdercoat (lead time applies)
tecHNical DetailsRL1 bottom rail; RL2 top rail; RL2 COC top overhead closer railSupplied in custom lengths with cover plates and end capsSpecify glass thickness: 10mm, 12mm, 15mm or 19mmRail length needs to be 9mm less than your glass to allow for end caps (please specify glass width)
rl3/rl4/rl4 coc Bottom and top locking door rails
availaBle fiNisHes• Satin silver anodised • Polished stainless steel • Satin stainless steel• Selected powdercoat (lead time applies)
tecHNical DetailsComplete with 590 lockRL3 bottom rail; RL4 top rail; RL4 COC top overhead closer railSpecify cylinder combination e.g. double cylinder, Cylinder/Turn, Single cylinder, Single turnSupplied in custom lengths with cover plates and end capsSpecify glass thickness: 10mm, 12mm, 15mm or 19mmRail length needs to be 9mm less than your glass to allow for end caps (please specify glass width)
rl5 Bottom and top non-locking sliding door rails
availaBle fiNisHes• Satin silver anodised • Polished stainless steel • Satin stainless steel• Selected powdercoat (lead time applies)
tecHNical DetailsRL5 bottom sliding railRL5 top sliding railSupplied in custom lengths with cover plates and end capsSpecify glass thickness: 10mm, 12mm, 15mm or 19mmRail length needs to be 9mm less than your glass to allow for end caps (please specify glass width)n.B. does not include sliding track system
specialsFloor guide availableRoller attachments available
C16
CALL: (09) 624-1180www.euroglass.co.nz
Total door width
Total door width
Total door width
32mm
32mm
32mm
59
84
59
84
59
84
door & patch fittings:dOOR RAiLS
rl6 Bottom and top locking sliding door rails
availaBle fiNisHes• Satin silver anodised • Polished stainless steel • Satin stainless steel• Selected powdercoat (lead time applies)
tecHNical DetailsSpecify cylinder combination e.g. double cylinder, Cylinder/Turn,
Single cylinder, Single turnSupplied in custom lengths with cover plates and end capsSpecify glass thickness: 10, 12, 15 or 19mmRail length needs to be 9mm less than your glass to allow for end caps (please specify glass width)n.B. does not include sliding track system
specialsFloorguide available, see below
rl7 Sidelight rail
availaBle fiNisHes• Satin silver anodised • Polished stainless steel • Satin stainless steel• Selected powdercoat (lead time applies)
tecHNical DetailsFrameless sidelight rail to match door railSupplied in custom lengths with cover plates and end capsSpecify glass thickness: 10mm, 12mm, 15mm or 19mmCH25 channel required to mount rail to floorRail length needs to be 9mm less than your glass to allow for end caps (please specify glass width)
fgr Guide
availaBle fiNisHes• Black nylon
tecHNical Details
FGR guide for euroglass sliding rail
C17
CALL: (09) 624-1180www.euroglass.co.nz
Total door width
32mm 59
84
fgrguide
32mm
Total door width
46mm
25mm
100mm
6mm
3
84
59
door & patch fittings:ViennA HYdRAULiC HinGeS
vieNNa HyDraulic HiNge Glass to walleH1Ho
availaBle fiNisHes• Polished stainless steel, marine grade 316
tecHNical Details
Made from aluminium and stainless steelHinge opening angle 100˚Self-closing from any angleAvailable as non-hold open (for pool environments) and hold open (doors)Maximum recommended glass weight; 70kgMaximum recommended door width; 900mmStandard for 12mm glass, can be supplied for 10mm or 15mm glass on requestScrew on each pivot block adjusts hydraulic closing speed
vieNNa HyDraulic HiNge Glass to wall, offseteH1lHo
availaBle fiNisHes• Polished stainless steel, marine grade 316
tecHNical Details
Made from aluminium and stainless steelHinge opening angle 100˚Self-closing from any angleAvailable as non-hold open (for pool environments) and hold open (doors)Maximum recommended glass weight; 70kgMaximum recommended door width; 900mmStandard for 12mm glass, can be supplied for 10mm or 15mm glass on requestScrew on each pivot block adjusts hydraulic closing speed
vieNNa HyDraulic HiNge Glass to glasseH2Ho
availaBle fiNisHes• Polished stainless steel, marine grade 316
tecHNical Details
Made from aluminium and stainless steelHinge opening angle 100˚Self-closing from any angleAvailable as non-hold open (for pool environments) and hold open (doors)Maximum recommended glass weight; 70kgMaximum recommended door width; 900mmStandard for 12mm glass, can be supplied for 10mm or 15mm glass on requestScrew on each pivot block adjusts hydraulic closing speed
6
C18
CALL: (09) 624-1180www.euroglass.co.nz
78
84
R 13
R 5
50
glass cut-out detail
563
120
909
24
11.5
HYDRAULIC HINGEWITH "L" WALL MOUNTING PLATE
This drawing remainsthe property of
Euroglass Systems Ltd
COPYRIGHT 2010
563
120
90
9
24
11.5
HYDRAULIC HINGEWITH "L" WALL MOUNTING PLATE
This drawing remainsthe property of
Euroglass Systems Ltd
COPYRIGHT 2010
11.55 63
45
120
90
door & patch fittings:GLAZinG CHAnneL
cu25/cu45 Channel
availaBle fiNisHes• Mill finish• Satin silver anodised
tecHNical Details
Stock length: 5m Thickness 2.5mm
com1/com2 Commercial glazing U channel com3 end cap
availaBle fiNisHes• Satin anodised• Mill finish
tecHNical Details
Heavy duty one or two-piece architectural commercial channel section, used for interior and exterior applications Suitable for 10, 12 and 15mm glass, can be used with 19mm if wet glazed
CU25channel
CU45channel
500mm25mm
20mm
500mm 500mm
20mm
45mm
2.5mm
COM1 Bottom Channel
COM2 Head/Side Channel
COM3 end Cap
32
45
32
45
20.4
3933
20.4
C19
CALL: (09) 624-1180www.euroglass.co.nz