dk fr desensorlink.com.ua/pdf/5102v103.pdf · min. span for rtd-indgang er 50°c, for lineær...
TRANSCRIPT
Programmable displays with a wide se-lection of inputs and outputs for display of temperature, volume and weight, etc. Feature linearisation, scaling, and difference measurement functions for programming via PReset software.
Interfaces for analogue and digitalsignals as well as HART® signals between sensors / I/Pconverters / frequency signals and control systems in Ex zone 0, 1 & 2 and for some modules in zone 20, 21 & 22.
Galvanic isolators for analogue and digital signals as well as HART® signals. A wide product range with both loop-powered and universal isolators featuring linearisation, inversion, and scaling of output signals.
PC or front programmable modules with universal options for input, output and supply. This range offers a number of advanced features such as process calibration, linearisation and auto-diagnosis.
A wide selection of transmitters for DIN form B mounting and DIN rail modules with analogue and digital bus communication ranging from application-specifi c to universal transmitters.
Displays
Temperature
Isolation
Ex interfaces
Universal
DK
UK
FR
DE
Side 1
Page 9
Page 17
Seite 25
S I G N A L S T H E B E S T
5 1 0 2
R T D T r a n s m i t t e r
N o . 5 1 0 2 V 1 0 3 - I N ( 0 9 5 0 )F r o m s e r . n o . 9 7 0 1 1 7 0 0 1
RTD-TRANSMITTER
PRetrans type 5102
INDHOLDSFORTEGNELSE
Overensstemmelseserklæring . . . . . . . . . . . . . . . . . . . . . . 2Anvendelse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Teknisk karakteristik . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Indgang . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Udgang . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Elektriske specifikationer. . . . . . . . . . . . . . . . . . . . . . . . . . 4Bestillingsskema . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Blokdiagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65102 forbindelse til Loop Link. . . . . . . . . . . . . . . . . . . . . . 7
1
RTD-TRANSMITTER 5102
• Programmerbar via PC• Indgang for Pt100, Ni100 eller Ohm• Lineariseret analogudgang• 24 VDC forsyning• 1- eller 2-kanals version• DIN-skinne montering
ANVENDELSE:Lineariseret temperaturmåling med Pt100 eller Ni100 føler. Omsætning af lineær modstandsændring til standard analogt strøm- / spændingssignal, f.eks. fra ven-tiler, spjæld eller lineære bevægelser med påmonteret potentio meter. Som signalsimula tor via eksternt monteret 10-turns potentiometer.
TEKNISK KARAKTERISTIK:Generelt:Transmitteren kan opsættes til ønsket signaltype ved hjælp af en DOS-baseret PC med konfigurationspro grammet PReset 5000 og kommunikationsenhe-den Loop Link. Opsætning af transmitteren kan foretages uden tilslutning af forsyningsspænding, idet kommunikationsenheden leverer den nødvendige effekt. For syningsspændingen er 24 VDC med samme referencepunkt for for-synings-, indgangs- og ud gangsstel. Føler tilslutningen er altid en 3-leder tilslut-ning, hvor kabelkom pensering kan vælges op til 50 Ω i hver leder. Hvis 2-leder tilslutning ønskes, skal ben 43 og 42 (kanal 1) eller 53 og 52 (kanal 2) kort sluttesi tilslut ningsstikket (ingen kabel kompensering). Følerfejlsdetek tering kan vælges Upscale, Down scale eller indtastes til speciel udgangsværdi.
INDGANG:Lineariseret Pt100 temperaturindgang efter normen IEC 751 i området -200...+850°C. Lineariseret Ni100 temperaturindgang efter normen DIN 43760 i området -50...+250°C.Lineær mod standsindgang i området 0...10 kΩ. Min. span for RTD-indgang er 50°C, for lineær modstand 30 Ω. RTD-indgangen kan opsættes i multipla af hovedtypen (f.eks. Pt1000). Ind gangen kan reverseres, så 0% f.eks. er 150°C og 100% er 0°C.
3
OVERENSSTEMMELSESERKLÆRINGSom producent erklærer
PR electronics A/S
Lerbakken 10
DK-8410 Rønde
hermed at følgende produkt:
Type: 5102
Navn: RTD-transmitter
er i overensstemmelse med følgende direktiver og standarder:
EMC-direktivet 2004/108/EF og senere tilføjelser
EN 61326-1
For specifikation af det acceptable EMC-niveau henvises til moduletselektriske specifikationer.
Rønde, 23. februar 2009 Peter Rasmussen Producentens underskrift
2
Indgang:
Max. nulpunktsforskydning ........................ 50% af valgt max. værdiKabelmodstand pr. leder (prg.). .................. Max. 10...50 ΩFølerstrøm .................................................. > 0,2, < 0,4 mAPrimær nøjagtighed .................................... < ±0,3°CTemperaturkoef. for span < 100°C ............. < ±0,01°C/°Comg.Følerfejlsdetektering ................................... Upscale / Downscale / valgt værdi
Udgang:Signalområde ............................................. 0...20 mA / 0...10 VDCMin. signalområde ...................................... 5 mA / 250 mVMax. nulpunktsforskydning ........................ 50% af valgt max. værdiBelastning (max.) ........................................ 20 mA / 600 Ω / 12 VDCBelastningsstabilitet ................................... < 0,01% af span / 100 ΩStrømbegrænsning..................................... < 28 mA
GOST R godkendelse:VNIIM, Cert. no. .......................................... Se www.prelectronics.dk
Overholdte myndighedskrav: Standard:EMC 2004/108/EF ...................................... EN 61326-1
Af span = Af det aktuelt valgte område.
54
Type Min. værdi Max. værdi Min. span Standard
Pt100 -200°C +850°C 50°C IEC 751 Ni100 -50°C +250°C 50°C DIN 43760 Lin. R 0 Ω 10 kΩ 30 Ω -----
UDGANG:Den analoge udgang kan frit opsættes til strøm i området 0...20 mA eller spæn-ding i området 0...10 VDC, med et min. span på 5 mA eller 250 mVDC med max. offset på 50% af aktuel max. værdi. Spændingssignaler frembringes ved at kortslutte ben 13 og 12 (kanal 1) eller 23 og 22 (kanal 2) samt montere jumper for intern shunt modstand. For spændingssignaler i området 0...1 VDC anvendes 50 Ωshunt (JP1), i området 0...10 VDC 500 Ω shunt (JP2). Spændingssignalet udtages mellem ben 12 og 11 (kanal 1) eller 22 og 21 (kanal 2). Minimum belastnings modstand for spændingssignaler er 500 kΩ.
ELEKTRISKE SPECIFIKATIONER:
Specifikationsområde:-20°C til +60°C
Fælles specifikationer:Forsyningsspænding .................................. 19,2...28,8 VDCEgetforbrug ................................................ 1,7 W (2 kanaler)Opvarmningstid .......................................... < 5 min.Kommunikationsinterface........................... Loop LinkSignal- / støjforhold .................................... Min. 60 dBSignaldynamik, indgang ............................. 17 bitSignaldynamik, udgang ......................... 16 bitReaktionstid (0...90%, 100...10%) ............. < 165 msKalibreringstemperatur ............................... 20...28°CTemperaturkoefficient ................................. < ±0,01% /°Comg.Linearitetsfejl .............................................. < 0,1% af spanEMC-immunitetspåvirkning ........................ < ±0,5% af spanKlemskruetilspændingsmoment ................. 0,5 NmRelativ fugtighed ........................................ < 95% RH (ikke kond.)Mål (HxBxD) ............................................... 109 x 23,5 x 130 mmDIN-skinne type .......................................... DIN 46277Kapslingsklasse .......................................... IP20Vægt ........................................................... 170 g
76
File Product Input Output Communication Language Option 08:30:00
PRetop 5331
Date: 1994-8-10
943201594
PRelectronics
Analog inputAnalog output
Serial no:
Input type:Output type: 4 - 20mA
UpscaleSensor error:
Pt100 DIN/IEC
0.00 - 50.00C
3-wire
1.00 sec------
Input range:
Connection:
Cold junction comp:
Response time:
Tag no:
COM
5102Loop Link
KANAL 1
KANAL 2
5102 FORBINDELSE TIL LOOP LINK:
NB: Enheden kan programmeres med eller uden tilsluttet forsyning. Hvis enheden programmeres med tilsluttet forsyning, skal den afbrydes og tilsluttes igen efter endt programmering.
BESTILLINGSSKEMA:
BLOKDIAGRAM:
Type
5102
Kanaler
1 kanal : A
2 kanaler : B
Ved 2-tråds RTD-forbindelse kortsluttes ben 42 og 43.
8 9
RTD TRANSMITTER
PRetrans type 5102
TABLE OF CONTENTS
Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . 10Application. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Technical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . 11Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Electrical specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . 12Order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145102 connection to Loop Link . . . . . . . . . . . . . . . . . . . . . 15
RTD TRANSMITTER 5102
• Programmable via PC• Input for Pt100, Ni100 or Ohm• Linearised analogue output• 24 VDC supply• 1- or 2-channel version• DIN rail mounting
APPLICATION:Linearised temperature measurement with Pt100 or Ni100 sensor. Conversion of linear resistance change to standard analogue current / voltage signal from e.g. valves or linear movements with attached potentiometer. Signal simulator via externally mounted 10-turn potentiometer.
TECHNICAL CHARACTERISTICS:General:The transmitter may be configured to the requested signal type by means of a DOS-based PC with the configuration program PReset 5000 and the communi-cations unit Loop Link. The configuration of the transmitter may be done without connection of supply voltage as the communications unit supplies the required power. The supply voltage is 24 VDC with the same reference point for supply, input and output ground. The sensor connection is always a 3-wire connection with cable compensation for up to 50 Ω in each wire. If a 2-wire connection is requested, pin 43 and 42 (channel 1) or 53 and 52 (channel 2) must be short -circuited in the connection plug (no cable compensation). Sensor error detection is as standard set to Upscale, Downscale or entered to special output value.
INPUT:Linearised Pt100 temperature input according to IEC 751 within the range -200...+850°C. Linearised Ni100 temperature input according to DIN 43760 within the range -50...+250°C. Linear resistance input within the range 0...10 kΩ. Min. span for the RTD input is 50°C, for linear re sistance 30 Ω.The RTD input can be delivered set up in multiples of the main type (e.g. Pt1000). The input can be reversed so that 0% e.g. is 150°C and 100% is 0°C.
11
DECLARATION OF CONFORMITYAs manufacturer
PR electronics A/S
Lerbakken 10
DK-8410 Rønde
hereby declares that the following product:
Type: 5102
Name: RTD transmitter
is in conformity with the following directives and standards:
The EMC Directive 2004/108/EC and later amendments
EN 61326-1
For specification of the acceptable EMC performance level, refer to theelectrical specifications for the module.
Rønde, 23 February 2009 Peter Rasmussen Manufacturer’s signature
10
Input:
Max. offset ................................................. 50% of selected max. valueCable resistance per wire (prog.). .............. Max. 10...50 ΩSensor current ............................................ > 0.2, < 0.4 mABasic accuracy ........................................... < ±0.3°CTemp. coefficient for span <100°C ............ < ±0.01°C/°Camb.Sensor error detection ............................... Upscale / Downscale / selected value
Output:Signal range ............................................... 0...20 mA / 0...10 VDCMin. signal range ........................................ 5 mA / 250 mVMax. offset ................................................. 50% of selected max. valueLoad (max.) ................................................. 20 mA / 600 Ω / 12 VDCLoad stability .............................................. < 0.01% of span / 100 ΩCurrent limit ................................................ < 28 mA
GOST R approval:VNIIM, Cert. no. .......................................... See www.prelectronics.com
Observed authority requirements: Standard:EMC 2004/108/EC ..................................... EN 61326-1
Of span = Of the presently selected range.
13
OUTPUT:The analogue output may be configured to any current within the range 0...20 mA or voltage within the range 0...10 VDC with a min. span of 5 mA or 250 mVDC with a max. offset of 50% of the actual max. value. Voltage signals are produced by short-circuiting pin 13 and 12 (channel 1) or 23 and 22 (channel 2) together with mounting a jumper for internal shunt resistance. For voltage signals within the range 0...1 VDC a 50 Ω shunt (JP1) is used, within the range 0...10 VDC a 500 Ωshunt (JP2) is used. The voltage signal is avai lable between pin 12 and 11 (chan-nel 1), or 22 and 21 (channel 2). The min. load resistance for voltage signals is 500 kΩ.
ELECTRICAL SPECIFICATIONS:Specifications range:-20°C to +60°C
Common specifications:Supply voltage ........................................... 19.2...28,8 VDCInternal consumption ................................. 1.7 W (2 channels)Warm-up time ............................................. < 5 min.Communications interface ......................... Loop LinkSignal / noise ratio ..................................... Min. 60 dBSignal dynamics, input ............................... 17 bitSignal dynamics, output ........................ 16 bitResponse time (0...90%, 100...10%) ......... < 165 msCalibration temperature ............................. 20...28°CTemperature coefficient .............................. < ±0.01% /°Camb.Linearity error ............................................. < 0.1% of spanEMC immunity influence ............................ < ±0.5% of spanScrew terminal torsion ............................... 0.5 NmRelative air humidity ................................... < 95% RH (non-cond.)Dimensions (HxWxD) .................................. 109 x 23.5 x 130 mmDIN rail type ................................................ DIN 46277Protection degree ....................................... IP20Weight ........................................................ 170 g
12
Type Min. value Max. value Min. span Standard
Pt100 -200°C +850°C 50°C IEC 751 Ni100 -50°C +250°C 50°C DIN 43760 Lin. R 0 Ω 10 kΩ 30 Ω -----
15
ORDER:
14
5102 CONNECTION TO LOOP LINK:
File Product Input Output Communication Language Option 08:30:00
PRetop 5331
Date: 1994-8-10
943201594
PRelectronics
Analog inputAnalog output
Serial no:
Input type:Output type: 4 - 20mA
UpscaleSensor error:
Pt100 DIN/IEC
0.00 - 50.00C
3-wire
1.00 sec------
Input range:
Connection:
Cold junction comp:
Response time:
Tag no:
COM
5102Loop Link
CH 1
CH 2
NB: The module can be programmed whether the supply is connected or discon-nected. If the supply is connected during programming, the module must be disconnected and then reconnected after programming.
Type
5102
Channels
1 channel : A
2 channels : B
BLOCK DIAGRAM:
For 2-wire connection, short-circuit pin 42 and 43.
16
CONVERTISSEUR Pt100
PRetrans 5102
SOMMAIRE
Déclaration de conformité. . . . . . . . . . . . . . . . . . . . . . . . . 18Applications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Caractéristiques techniques . . . . . . . . . . . . . . . . . . . . . . . 19Entrée . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Sortie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Spécifications électriques . . . . . . . . . . . . . . . . . . . . . . . . . 20Référence de commande . . . . . . . . . . . . . . . . . . . . . . . . . 22Schéma de principe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Raccordement entre le PR-5102 et le kit de programmation . . . . . . . . . . . . . . . . . . . . . . . . 23
17
CONVERTISSEUR Pt100
• Programmable par PC• Entrée pour Pt100 Ω, Ni100 ou Ohm• Sortie analogique linéarisée• Alimentation 24 Vcc• Une ou deux voie(s)• Montage sur rail DIN
APPLICATIONS :Mesure de température linéarisée avec un capteur Pt100 Ω ou Ni 100. Conversion d’une résistance linéaire transformée en signal courant / tension standard à partir, par exemple, de vannes ou de mouvements linéaires avec le potentiomètre correspondant. Simulation d’un signal 4/20 mA par l’intermédiaire d’un potentiomètre 10-tours externe.
CARACTERISTIQUES TECHNIQUES :Généralités :Le transmetteur peut être configuré pour le type de signal requis au moyen d’un PC avec le programme de configuration PReset 5000 et l’unité de communication Loop Link. La configuration du transmetteur peut être réalisée sans en connecter l’alimentation puisque c’est l’unité de communication qui est utilisée pour cela. La tension d’alimentation est de 24 Vcc avec le même point de référence pour l’alimentation, l’entrée et la sortie. Le raccordement du capteur est toujours une connexion 3-fils avec une compensation de câble jusqu’à 50 Ω par conduc teur. Lorsqu’un raccordement 2-fils est realisé, un court-circuit entre les bornes 43 et 42 (voie 1) et 53 et 52 (voie 2) doit être réalisé (pas de compensation de câble). La détection de rupture capteur est, en standard, programmable sur haut d’échelle, bas d’échelle ou modifiée à une valeur spéciale de sortie.
ENTREE :Entrée de température Pt100 Ω linéarisée conforme à la norme IEC 751 dans la plage de -200...+850°C. Entrée de température Ni 100 linéarisée conforme à la norme DIN 43760 dans la plage de -50...+250°C. Entrée de résistance linéaire dans la plage de 0...10 kΩ. Le minimum d’échelle est de 50°C pour l’entrée RTD,
19
DECLARATION DE CONFORMITEEn tant que fabricant
PR electronics A/S
Lerbakken 10
DK-8410 Rønde
déclare que le produit suivant :
Type : 5102
Nom : Convertisseur Pt100
correspond aux directives et normes suivantes :
La directive CEM (EMC) 2004/108/CE et les modifications subséquentes
EN 61326-1
Pour une spécification du niveau de rendement acceptable CEM (EMC)renvoyer aux spécifications électriques du module.
Rønde, le 23 février 2009 Peter Rasmussen Signature du fabricant
18
Entrée :
Décalage max. ........................................... 50% de la valeur max. sélectionnéeRésistance de ligne par fil .......................... Max. 10...50 ΩCourant de sonde ...................................... > 0,2, < 0,4 mAPrécision de base ....................................... < ±0,3°CCoefficient de temp. de l’EC < 100°C ....... < ±0,01°C/°Camb.Détection rupture capteur .......................... Haut d’échelle / bas d’échelle / autre valeurSortie :Gamme de mesure ..................................... 0...20 mA / 0...10 VccPlage de mesure min ................................. 5 mA / 250 mVDécalage max. ........................................... 50% de la valeur max. sélectionnéeRésistance de charge ................................. 20 mA / 600 Ω / 12 VccStabilité sous charge .................................. < 0,01% de l’EC / 100 ΩLimite de courant ....................................... < 28 mA
Approbation GOST R :VNIIM, Cert. no. .......................................... Voir www.prelectronics.fr
Agréments et homologations : Standard :CEM (EMC) 2004/108/CE .......................... EN 61326-1
EC = Echelle configurée
21
de 30 Ω pour la résistance linéaire. L’entrée RTD peut être programmée dans les multiples du type principal (par exemple Pt1000). L’entrée peut être inversée de façon à ce que 0% par exemple soit égal à 150°C et 100% à 0°C.
SORTIE : La sortie analogique peut être configurée aussi bien en courant dans la plage de 0...20 mA qu’en tension dans la plage de 0...10 Vcc avec un minimum d’échelle de 5 mA ou 250 mVcc avec un maximum de décalage de 50% de la valeur maximale configuré. Le signal tension est obtenu à l’aide d’un shunt entre les bornes 13 et 12 (voie 1) ou 23 et 22 (voie 2) avec le positionnement d’un cavalier pour la résistance interne.Pour le signal tension, on utilise :- une résistance de 50 Ω (JP1) dans la plage de 0...1 Vcc,- une résistance de 500 Ω (JP2) dans la plage de 0...10 Vcc.Le signal tension est disponible entre les bornes 12 et 11 (voie 1) ou 22 et 21(voie 2). La résistance de charge min. pour un signal tension est de 500 kΩ.
SPECIFICATIONS ELECTRIQUE :Plage des spécifications :-20°C à +60°C
Spécifications communes :Tension d’alimentation ............................... 19,2...28,8 VccConsommation interne ............................... 1,7 W (2 voies)Temps de chauffe ....................................... < 5 min.Interface de communication ...................... Loop LinkRapport signal / bruit ................................. Min. 60 dBDynamique du signal d’entrée ................... 17 bitDynamique du signal de sortie................ 16 bitTemps de réponse (0...90%,100...10%) ................................... < 165 msTempérature d’étalonnage ......................... 20...28°CCoefficient de température ........................ < ±0,01% /°Camb.Erreur de linéarité ....................................... < 0,1% de l’ECCEM (EMC) : Effet de l’immunité ................ < ±0,5% de l’ECPression max. avant déformation de la vis . 0,5 NmHumidité relative ........................................ < 95% HR (sans cond.)Dimensions (HxLxP) ................................... 109 x 23,5 x 130 mmType de rail DIN .......................................... DIN 46277Degré de protection ................................... IP20Poids .......................................................... 170 g
20
Type Temp. min Temp. max. Plage min. Standard
Pt100 -200°C +850°C 50°C IEC 751 Ni100 -50°C +250°C 50°C DIN 43760 R lin. 0 Ω 10 kΩ 30 Ω -----
23
REFERENCE DE COMMANDE :
22
File Product Input Output Communication Language Option 08:30:00
PRetop 5331
Date: 1994-8-10
943201594
PRelectronics
Analog inputAnalog output
Serial no:
Input type:Output type: 4 - 20mA
UpscaleSensor error:
Pt100 DIN/IEC
0.00 - 50.00C
3-wire
1.00 sec------
Input range:
Connection:
Cold junction comp:
Response time:
Tag no:
COM
5102Loop Link
VOIE 1
VOIE 2
RACCORDEMENT ENTRE LE PR-5102 ET LE KIT DE PROGRAMMATION :
Type
5102
Voies
1 voie : A
2 voies : B
SCHEMA DE PRINCIPE :
Pour un capteur raccordé en 2-fils, les bornes 42 et 43doivent être mises en court-circuit
N.B. : La programmation peut être effec tuée avec l’alimentation connectée ou déconnectée. Si l’alimentation est connec tée pendant la programmation, le module doit être débranché et puis rebranchée quand la programmation a été achevée.
24 25
WTH-MESSUMFORMER
PRetrans Typ 5102
INHALTSVERZEICHNIS
Konformitätserklärung. . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Anwendung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Technische Merkmale . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Eingang . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Ausgang . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Elektrische Daten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Bestellangaben . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Blockdiagramm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305102 Verbindung mit Loop Link . . . . . . . . . . . . . . . . . . . . 31
WTH-MESSUMFORMER
• Programmierbar über PC• Eingang für Pt100, Ni100 oder Ohm• Linearisierter Analogausgang• 24 VDC Versorgung• Ein- und Zweikanalversion• DIN-Schienenmontierung
ANWENDUNG:Linearisierte Temperaturmessung mit Pt100- oder Ni100-Fühler. Umwandlung von linearer Widerstandsänderung in analoges Standard Strom- / Spannungssig-nal, z.B. von Ventilen, Ventilklappen oder linearen Bewegungen bei aufge setztemPotentiometer. Als Signalsimulator über extern montiertes Potentiometer (10 Umdrehungen).
TECHNISCHE MERKMALE:Der Messumformer kann auf den gewünschten Signaltyp mit Hilfe eines DOS-basierten PCs mit dem Konfigurationsprogramm PReset 5000 und der Kommu-nikationseinheit Loop Link eingestellt werden. Das Einstellen des Mess umformerskann ohne Anschluss einer Versorgungsspannung vorgenommen werden, da die Kommunikationseinheit die notwendige Leistung liefert. Die Versorgungsspannung beträgt 24 VDC mit dem gleichen Referenzpunkt für Versorgungs-, Eingangs- und Ausgangsmaße. Der Fühleranschluss ist immer ein 3-Leiter-Anschluss, bei dem die Kabelkompensation bis zu 50 Ω in jedem Leiter gewählt werden kann. Wird ein 2-Leiter-Anschluss gewünscht, müssen die An schlüsse 43 und 42 (Kanal 1) oder die Anschlüsse 53 und 52 (Kanal 2) im Anschlussstecker kurzgeschlossen werden (keine Kabelkomp.). Eine Fühler-fehlererkennung kann Upscale, Downscale gewählt oder zu einem speziellen Ausgangswert eingetastet werden.
EINGANG:Linearisierter Pt100-Temperatureingang gemäß der Norm IEC 751 im Bereich -200...+850°C. Linearisierter Ni100-Temperatureingang gemäß der Norm DIN 43760 im Bereich -50...+250°C. Linearer Widerstandseingang im Bereich 0...10 kΩ.Die Minimalspanne liegt für WTH-Eingänge bei 50°C, für linearen Widerstand
27
KONFORMITÄTSERKLÄRUNGAls Hersteller bescheinigt
PR electronics A/S
Lerbakken 10
DK-8410 Rønde
hiermit für das folgende Produkt:
Typ: 5102
Name: WTH-Messumformer
die Konformität mit folgenden Richtlinien und Normen:
Die EMV Richtlinien 2004/108/EG und nachfolgende Änderungen
EN 61326-1
Zur Spezifikation des zulässigen Erfüllungsgrades, siehe die Elektrische Daten des Moduls.
Rønde, 23. Februar 2009 Peter Rasmussen Unterschrift des Herstellers
26
Eingang:
Max. Nullpunktverschiebung ...................... 50% des gewählten MaximalwertesKabelwiderstand pro Leiter (prg.) ............... Max. 10...50 ΩFühlerstrom ................................................ > 0,2 mA, < 0,4 mAGrundgenauigkeit ....................................... ±0,3°CTemp.koeffizient d. Messspanne <100°C .. < ±0,01°C/°CUmg.Fühlerfehlererkennung ................................ Upscale / Downscale / gewählter Wert
Ausgang:Signalbereich .............................................. 0...20 mA / 0...10 VDCMin. Signalbereich ...................................... 5 mA / 250 mVMax. Nullpunktverschiebung ...................... 50% des gewählten MaximalwertesMaximalbelastung ...................................... 20 mA / 600 Ω / 12 VDCBelastungsstabilität .................................... < 0,01% d. Messspanne / 100 ΩStrombegrenzung ....................................... < 28 mA
GOST R Zulassung;VNIIM, Cert. no. .......................................... Siehe www.prelectronics.de
Eingehaltene Richtlininen: Norm:EMV 2004/108/EG ...................................... EN 61326-1
d. Messspanne = der gewählten Messspanne
29
beträgt sie 30 Ω. Der WTH-Eingang kann als ein Mehrfaches des Haupttyps (z.B. Pt1000) konfiguriert werden. Der Eingang kann so invertiert werden, dass 0% z.B. 150°C und 100% 0°C entspricht
AUSGANG:Der analoge Ausgang kann frei für Strom im Bereich 0...20 mA oder Spannung im Bereich 0...10 VDC eingestellt werden, mit einem Minimalbereich von 5 mA oder 250 mVDC und mit einer maximalen Nullpunktverschiebung von 50% des jeweiligen Maximalwertes.Spannungssignale werden hervorgebracht, indem man die Anschlüsse 13 und 12 (Kanal 1) oder die Anschlüsse 23 und 22 (Kanal 2) kurzschließt, sowie eine Überbrückung für internen Nebenwiderstand montiert. Für Spannungssignale im Bereich 0...1 VDC wird ein 50-Ω−Nebenwiderstand (JP1) und im Bereich 0...10 VDC ein 500-Ω−Nebenwiderstand (JP2), angewandt. Das Spannungssignal liegt auf den Anschlüssen 12 und 11 (Kanal 1) oder auf den Anschlüssen 22 und 21 (Kanal 2) an. Der kleinste Belastungswiderstand für Spannungssignale beträgt 500 kΩ.
ELEKTRISCHE DATEN:Umgebungstemperatur:-20°C bis +60°C
Allgemeine Daten:Versorgungsspannung ................................ 19,2...28,8 VDCEigenverbrauch .......................................... 1,7 W (2 Kanale)Aufwärmzeit................................................ < 5 min.Kommunikationsschnittstelle ..................... Loop LinkSignal- / Rauschverhältnis ......................... Min. 60 dBSignaldynamik, Eingang ............................. 17 BitSignaldynamik, Ausgang ........................ 16 BitAnsprechzeit (0...90%, 100...10%) ............ < 165 msKalibrierungstemperatur ............................. 20...28°CTemperaturkoeffizient ................................. < ±0,01% /°CUmg.Linearitätsfehler .......................................... < 0,1% d. MessspanneEMV-Immunitätseinfluss ............................. < ±0,5% d. MessspanneKlemmschraubenanzugsmoment............... 0,5 NmRelative Luftfeuchtigkeit ............................. < 95% RF (nicht kond.)Abmessungen (HxBxT) ............................... 109 x 23,5 x 130 mmDIN-Schiene Typ ........................................ DIN 46277Schutzart .................................................... IP20Gewicht ...................................................... 170 g
28
Typ Min. Wert Max. Wert Min. Bereich Norm
Pt100 -200°C +850°C 50°C IEC 751 Ni100 -50°C +250°C 50°C DIN 43760 Lin. R 0 Ω 10 kΩ 30 Ω -----
31
BESTELLANGABEN:
30
5102 VERBINDUNG MIT LOOP LINK:
File Product Input Output Communication Language Option 08:30:00
PRetop 5331
Date: 1994-8-10
943201594
PRelectronics
Analog inputAnalog output
Serial no:
Input type:Output type: 4 - 20mA
UpscaleSensor error:
Pt100 DIN/IEC
0.00 - 50.00C
3-wire
1.00 sec------
Input range:
Connection:
Cold junction comp:
Response time:
Tag no:
COM
5102Loop Link
KANAL 1
KANAL 2
BLOCKDIAGRAMM:
Wird ein 2-Draht-Anschluss gewünscht, müssen die Anschlüsse 43 und 42 im Anschlussstecker kurzgeschlossen werden.
Typ
5102
Kanäle
1 Kanal : A
2 Kanäle : B
Das Modul kann ohne Versorgungsspannung und unter Spannung programmiert werden. Wird das Gerät unter Spannung programmiert, muss nach der Pro-grammierung das Modul durch trennen der Versorgungsspannungsan schlüssezurückgesetzt werden.
PR electronics A/S tilbyder et bredt program af analoge og digitale signalbehandlingsmoduler til industriel automation. Programmet består af Isolatorer, Displays, Ex-barrierer, Temperaturtransmittere, Universaltransmittere mfl . Vi har modulerne, du kan stole på i selv barske miljøer med elektrisk støj, vibrationer og temperaturudsving, og alle produkter opfylder de strengeste internationale standarder. Vores motto »Signals the Best« er indbegrebet af denne fi losofi – og din garanti for kvalitet.
PR electronics A/S offers a wide range of analogue and digital signal conditioning modules for industrial automation. The product range includes Isolators, Displays, Ex Interfaces, Temperature Transmitters, and Universal Modules. You can trust our products in the most extreme environments with electrical noise, vibrations and temperature fl uctuations, and all products comply with the most exacting international standards. »Signals the Best« is the epitome of our philosophy – and your guarantee for quality.
PR electronics A/S offre une large gamme de produits pour le traite ment des signaux analogiques et numériques dans tous les domaines industriels. La gamme de produits s’étend des transmetteurs de température aux affi cheurs, des isolateurs aux interfaces SI, jusqu’aux modules universels. Vous pouvez compter sur nos produits même dans les conditions d’utilisation sévères, p.ex. bruit électrique, vibrations et fl uctuations de température. Tous nos produits sont conformes aux normes internationales les plus strictes. Notre devise »SIGNALS the BEST« c’est notre ligne de conduite - et pour vous l’assurance de la meilleure qualité.
PR electronics A/S verfügt über ein breites Produktprogramm an analogen und digitalen Signalverarbeitungsmodule für die in-dustrielle Automatisierung. Dieses Programm umfasst Displays, Temperaturtransmitter, Ex- und galvanische Signaltrenner, und Universalgeräte. Sie können unsere Geräte auch unter extremen Einsatzbedingungen wie elektrisches Rauschen, Erschütterungen und Temperaturschwingungen vertrauen, und alle Produkte von PR electronics werden in Überein stimmung mit den strengsten internationalen Normen produziert. »Signals the Best« ist Ihre Garantie für Qualität!
DK
UK
FR
DE
SubsidiariesFrancePR electronics SarlZac du Chêne, Activillage4, allée des SorbiersF-69673 Bron Cedex
GermanyPR electronics GmbHIm Erlengrund 26D-46149 Oberhausen
ItalyPR electronics S.r.l.Via Giulietti, 8IT-20132 Milano
SpainPR electronics S.L.Avda. Meridiana 354, 9° BE-08027 Barcelona
SwedenPR electronics ABAugust Barks gata 6AS-421 32 Västra Frölunda
UKPR electronics UK LtdMiddle Barn, ApuldramChichesterWest Sussex, PO20 7FD
USAPR electronics Inc11225 West Bernardo CourtSuite ASan Diego, California 92127
[email protected]. +33 (0) 4 72 14 06 07fax +33 (0) 4 72 37 88 20
[email protected]. +49 (0) 208 62 53 09-0fax +49 (0) 208 62 53 09 99
[email protected]. +39 02 2630 6259fax +39 02 2630 6283
[email protected]. +34 93 311 01 67fax +34 93 311 08 17
[email protected]. +46 (0) 3149 9990fax +46 (0) 3149 1590
[email protected]. +44 (0) 1243 776 450fax +44 (0) 1243 774 065
[email protected]. +1 858 521 0167fax +1 858 521 0945
Head offi ce
Denmark www.prelectronics.comPR electronics A/S [email protected] 10 tel. +45 86 37 26 77DK-8410 Rønde fax +45 86 37 30 85