de werkwijze en open standaarden
TRANSCRIPT
DURA VERMEER KIEST VOOR
OPEN STANDAARDENMET OPEN STANDAARDEN DE SAMENWERKING INVULLING GEVEN
>DURAVERMEER.NL/EXPERTISE/BIM
VOORWOORD
De afgelopen jaren was het een interessante ontdekkingsreis door de jungle van het BIM landschap. Na het opstarten, bouwen en opleveren van diverse projecten kunnen we achterom kijken en de gebaande paden in het landschap ontdekken. Nu is het tijd om een routebeschrijving uit te gaan delen zodat we de juiste bagage mee nemen, de lastige afdalingen en beklimmingen over kunnen slaan en zo efficiënt mogelijk ons doel bereiken. De ontwikkelingen staan niet stil, we zijn nog niet klaar! “Open Standaarden” Dit boek is een samenvatting van de nu (anno 2015) geldende landelijke en internationale normen en afspraken in relatie tot het proces, structuur en informatie. Als Dura Vermeer Bouw & Vastgoed zijnde hebben we centraal afspraken gemaakt over de normen die gehanteerd zullen worden en welke prioritering daaraan wordt gegeven:
1. RVB BIM norm v1.1 2. ISO 16739:2013 – i.c.m. IFC 2x3 3. NL-SfB (minimaal 4 karakters) 4. Dutch Revit Standards (DRS) V2.0
Hierin geeft de RVB BIM norm voornamelijk invulling op het gebied van structuur. Hierin wordt verwezen naar IFC 2x3 conform de ISO norm. Deze geeft de basis waar welke informatie volgens een eenduidige manier geplaatst kan worden. NL- SfB geeft helderheid in structuur en zorgt ervoor dat objecten eenvoudig herleidbaar zijn. Tot slot geeft de DRS, indien in Revit wordt gemodelleerd, handvatten aan modelleurs voor naamgeving en wijze van modelleren. Waarom kiest Dura Vermeer Bouw & Vastgoed voor Open Standaarden? Hier zijn vele redenen voor, maar de belangrijkste is dat wij een schakel in de keten zijn. Waarbij we ons realiseren dat de partijen waarmee wij samenwerken ook in andere ketens actief zijn. Om spraakverwarring te vermijden en de partijen waarmee wij samenwerken niet een Dura Vermeer methode op te leggen, is het volgens ons het beste om aan te sluiten bij de ontwikkelingen in de markt. Hiermee ook de algemene ontwikkeling van en de innovatie binnen de bouwsector te versnellen. Het geeft de andere partijen tevens meer reden om te investeren en aan te sluiten bij deze manier van werken. Met BIM in de keten efficiënter, sneller, beter, goedkoper en leuker bouwen!
INHOUDSOPGAVE
1. Rijks Vastgoed Bedrijf a. RVB BIM Norm v1.1
2. NL-SfB; elementenmethode ‘91 a. Toelichting
3. IFC a. Toelichting b. Entiteiten c. Quantities, Base Quantities en Propertysets d. IFC Parameteroverzicht
4. Samenhang standaarden a. BIM van structuur naar de gewenste output
13 woningen Mille Fleurs Waterzoom - Ede
1
RVB BIM Norm
Versie 1.1 | 1 februari 2013
Rijksvastgoedbedrijf
Alle rechten voorbehouden. Alle auteursrechten en databankrechten ten
aanzien van deze uitgave worden uitdrukkelijk voorbehouden.
Deze rechten berusten bij de Staat / het Rijksvastgoedbedrijf.
Behoudens de in of krachtens de Auteurswet 1912 gestelde uitzonde-
ringen, mag niets uit deze uitgave worden verveelvoudigd, opgeslagen
in een geautomatiseerd gegevensbestand of openbaar gemaakt in
enige vorm of op enige wijze, hetzij elektronisch, mechanisch, door
fotokopieën, opnamen of enige andere manier, zonder voorafgaande
schriftelijke toestemming van het Rijksvastgoedbedrijf.
RVB BIM Norm | 3
1 Begripsbepaling 6
1.1 Algemeen 61.2 Contextspecifiek 61.2.1 DBFMO, DBM en MC 6
2 BIM-extracten 8
2.1 Algemene vereisten aan BIM-extracten 82.1.1 Coördinatie en aspectinformatie 82.1.2 Lokale positie en oriëntatie 82.1.3 Structuur en naamgeving 92.1.4 Correct gebruik van entiteiten 92.1.5 Nauwkeurigheid 92.1.6 Doublures en doorsnijdingen 92.1.7 Modeleenheid (units), maataanduidingen, maateenheden en getalafronding 102.1.8 Informatie-indelingssystematiek en -naamgeving 102.1.9 Bouwlaagindeling (levels) en -naamgeving 102.2 Specificaties van het IFC-model 122.2.1 Begripsbepaling 122.2.2 Toepassingsgebied 122.2.3 Normatieve referenties 122.2.4 Bestandsformaat en -naam 122.2.5 Opleveringsvereisten 122.2.6 IFC-model 132.2.6.1 Geometrisch detailleringsniveau 132.2.6.2 Informatie-indeling (classification) 132.2.6.3 Objectrelaties 132.2.6.4 ObjectGUID 132.2.6.5 Geografische positie en oriëntatie 132.2.7 IFC-objecten 142.2.7.1 Project 142.2.7.2 Terrein 142.2.7.3 Bouwwerk 142.2.7.4 Bouwlaag 152.2.7.5 Bouwlaagoppervlakobject 152.2.7.6 Ruimte 152.2.7.7 Groepering van ruimten: zones 162.2.7.8 Bouwkundige, constructieve en installatietechnische elementen 182.2.7.8.1 Aspect brandveiligheid 192.2.7.8.2 Discipline constructie 192.2.7.9 Groepering van constructieve elementen 192.2.7.10 Groepering van installatietechnische elementen 192.2.7.11 Inventaris-, inrichtings- en uitrustingselementen 19
Inhoudsopgave
RVB BIM Norm | 4
2.3 Specificaties van de CAD-tekening 202.3.1 Begripsbepaling 202.3.2 Toepassingsgebied 202.3.3 Normatieve referenties 202.3.4 Bestandsformaat en -naam 202.3.5 Opleveringsvereisten 212.3.6 CAD-entiteiten 212.3.7 CAD-tekening 212.3.7.1 Tekeningblad 212.3.7.2 Detailleringsniveau 212.3.7.2.1 Discipline bouwkunde 212.3.7.2.2 Discipline constructie 222.3.7.2.3 Discipline werktuigbouwkunde 222.3.7.2.4 Discipline elektrotechniek 222.3.7.2.5 Aspect brandveiligheid 222.3.7.3 Tekeningstructuur 222.3.7.3.1 Aspect brandveiligheid 232.3.7.4 Informatielaagindeling (layers) en -naamgeving 242.3.7.4.1 Aspect brandveiligheid 242.4 Specificaties van de meetstaten, berekeningen, uittrekstaten 252.4.1 Begripsbepaling 252.4.2 Toepassingsgebied 252.4.3 Referenties 252.4.4 Bestandsformaat en -naam 25
3 Bij de BIM-extracten te leveren bestanden 26
3.1 Algemeen 263.1.1 BIM 263.1.2 Modeldocumentatie 263.1.3 Bestandenlijst 263.2 Contextspecifiek 273.2.1 DBFMO, DBM en MC 273.2.1.1 Relatietabel prestatiespecificaties 27
4 Bijlage 28
4.1 Nomenclatuur Bouwbesluit 2012 284.1.1 Ruimtefunctie 284.1.2 Gebruiksfunctie 284.1.3 Gebruiksgebied 284.1.4 Verblijfsgebied 284.1.5 Brandcompartimentering 284.1.6 Vluchtroute 284.2 Titelblok- en tekeninglijstgegevens 284.3 Brandveiligheid: symbolen en lijnen 284.4 Relatietabel sjabloon 28
RVB BIM Norm | 5
De Rijksvastgoedbedrijf BouwwerkInformatieModel Norm, kortweg RVB BIM Norm, beschrijft de specificaties van BIM-extracten en de bij deze extracten aan te leveren bestanden.
De RVB BIM Norm beschrijft noch het proces, noch de stapsgewijze technische details om tot het resultaat volgens de voorgeschreven specificaties te komen; de RVB BIM Norm omvat geen BIM/CAD handleiding.
Inleiding
RVB BIM Norm | 6
1.1 Algemeen
In de RVB BIM Norm worden de volgende begrippen gehanteerd:
• bouwwerk: het geheel aan bouwwerkelementen. • bouwwerkelement: een ruimtelijk of materieel onderdeel van het bouwwerk. Bouwwerkelementen zijn
de ruimtelijke, bouwkundige, constructieve en installatietechnische elementen of componenten, alsook inventaris-, uitrustings- en inrichtingselementen.
• bouwlaag: de groepering van alle bouwwerkelementen die bij een te onderscheiden verdieping van het bouwwerk behoren.
• bouwwerkinformatieproducten: de (combinaties van) bestanden en documenten die het bouwwerk beschrijven, bijvoorbeeld 3D-modellen, 2D-tekeningen en producten die gebruik maken van bouwwerk-gegevens, zoals uittrekstaten, meetstaten, berekeningen etc.
• BIM of bouwwerkinformatiemodel: het integrale 3D-informatiebronmodel van het bouwwerk zoals dit met BIM-objecten opgezet wordt in een BIM-modelleerapplicatie. Het BIM kan uit meerdere afzonderlijke modellen bestaan, ondermeer omwille van uitsplitsing op basis van de verschillende disciplines of aspecten. Het BIM omvat alle bouwwerkinformatie die benodigd is om de vereiste BIM-extracten te produceren.
• BIM-object: iedere entiteit in het BIM die informatie van het bouwwerk bevat of beschrijft, al dan niet met een geometrische representatie. Toelichting: De representatie van een bouwwerkelement in het BIM is een BIM-object.
• BIM-object-ID: vrij te kiezen identificatiecode van een BIM-object welke uniek is binnen het BIM en overgeërfd wordt binnen bepaalde BIM-extracten, en waarmee eenduidige koppelingen gemaakt kunnen worden met andere informatiegegevens.
• BIM-extracten: de bouwwerkinformatieproducten die uit het BIM afgeleid of geëxporteerd worden.
1.2 Contextspecifiek
Naargelang de specifieke context, zoals de aard van het contract of project, waarbij het aanleveren van BIM-extracten vereist is, zijn aanvullende begrippen van toepassing.
1.2.1 DBFMO, DBM en MCBij DBFMO, DBM en MC worden de volgende aanvullende begrippen gehanteerd:
• Object: in de RVB BIM Norm dient het begrip bouwwerk als het Object te worden begrepen. Het begrip Object, met hoofdletter “O”, is gedefinieerd in de Overeenkomst. Toelichting: Het begrip Object is onderscheiden van het begrip BIM-object.
• BIM: aanvullend op de algemene begripsbepaling omvat het BIM in het algemeen de representatie van het bouwwerk (het Object) en in het bijzonder de representatie van alle functievervullers waaruit het bouwwerk is samengesteld.
• functie: de door Opdrachtgever vereiste functie zoals beschreven in de prestatiespecificaties.• functie-ID: unieke identificatiecode van de functie.
Toelichting: Deze identificatiecode is de unieke code zoals die in de prestatiespecificaties aan een functie is toegekend.
1. Begripsbepaling
RVB BIM Norm | 7
• functievervuller: in de RVB BIM Norm dient het begrip bouwwerkelement als functievervuller te worden begrepen. Het is de door Opdrachtnemer geleverde oplossing als vervuller van de vereiste functie. Toelichting: Ten behoeve van een correcte representatie van de vervuller van een vereiste functie kan het nodig zijn om BIM-objecten zoals ruimten in het BIM op te splitsen.
• identificatielabel-ID: unieke identificatiecode van het fysieke identificatielabel (e.g. RFID-tag) van de functievervuller.
• functievervuller-ID: in de RVB BIM Norm dient het begrip BIM-object-ID als functievervuller-ID te worden begrepen. Toelichting: Deze identificatiecode is de door Opdrachtnemer vrij te kiezen, doch unieke code toegekend aan de functiever-vuller in het model.
• relatietabel: de door Opdrachtnemer op te stellen oplossing met de expliciete en ondubbelzinnige koppeling van de functievervuller-IDs aan de functie-IDs of van de functievervuller-IDs aan de identificatielabel-IDs.
RVB BIM Norm | 8
Onder BIM-extracten wordt begrepen:
• IFC-model;• CAD-tekening;• meetstaten, berekeningen, uittrekstaten etc.
2.1 Algemene vereisten aan BIM-extracten
In de RVB BIM Norm worden eisen gesteld aan de aan te leveren eindproducten, de BIM-extracten. Om de onderlinge consistentie van BIM-extracten te borgen naar opzet, structuur en naamgeving, zijn de in dit hoofdstuk gestelde vereisten op alle BIM-extracten van toepassing.
Toelichting: • Het exporteren van een BIM-extract vanuit het BIM-bronbestand met de bijbehorende BIM-modelleerapplicatie geeft geen
automatische garantie dat het resulterende BIM-extract voldoet aan de gestelde eisen. De aanleverende partij is te allen tijde zelf verantwoordelijk voor de technische en inhoudelijke validiteit van het BIM-extract.
• Er zijn geen merkspecifieke vereisten gesteld aan de BIM-modelleerapplicaties die benodigd zijn voor het produceren van de vereiste BIM-extracten. De applicaties moeten evenwel geschikt zijn om op correcte, efficiënte, eenvoudige en herhaalbare wijze de extracten volgens de vereiste specificaties uit het BIM te extraheren.
2.1.1 Coördinatie en aspectinformatieDe BIM-extracten, zoals IFC-modellen en CAD-tekeningen, zijn onderling gecoördineerd. Om aspectspecifieke informatie inzichtelijk te clusteren, ondermeer op basis van de gebruikelijk te onderscheiden disciplines, zijn de BIM-extracten uitgesplitst in separate aspectextracten. Deze aspect -extracten zijn onderling gecoördineerd. Het BIM-extract in de discipline bouwkunde of architectuur is het basis- en referentiemodel, dan wel de tekenkundige onderlegger voor alle andere BIM-extracten.
Toelichting: Coördinatie houdt ondermeer in dat bij het samenvoegen van de aspectmodellen of -tekeningen tot één model of tekening, alle geëxtraheerde (i.c. geëxporteerde) BIM-objecten in het BIM-extract de correcte schaal, locatie en oriëntatie hebben, zonder dat een verschaling, translatie of rotatie van een aspectmodel of -tekening hiervoor nodig is.
2.1.2 Lokale positie en oriëntatieLokale positie: in het BIM-extract is de representatie van het bouwwerk als model of tekening vlakbij het nulpunt gepositioneerd. Lokale oriëntatie: de representatie van het bouwwerk is in het algemeen zodanig georiënteerd dat de orthogonaliteit samenvalt met de x- en y-as én dat in een bovenaanzicht het noorden zoveel als mogelijk naar de bovenkant, dan wel de hoofdingang naar de onderkant wijst.
Toelichting: • De lokale positie en oriëntatie is onderscheiden van de geografische positie en oriëntatie. De vastlegging van de geografische
positie en oriëntatie is naargelang de BIM-extractsoort nader gespecificeerd. • Bij de CAD-tekening wordt onder nulpunt, het nulpunt van het World Coordinate System (WCS) begrepen.
2. BIM-extracten
RVB BIM Norm | 9
2.1.3 Structuur en naamgevingVoor zover elders in de RVB BIM Norm niet nader gespecificeerd, zijn alle bestanden van of behorend bij een BIM-extract én alle entiteiten en gegevens in een BIM-extract op een logische, betekenisvolle, herkenbare, inzichtelijke, begrijpelijke en consistente wijze gestructureerd en naam gevoerd.
Toelichting: Ten behoeve van het minimaliseren van interoperabiliteitsproblemen bij de uitwisseling en koppeling van gegevens beginnen de invulwaarden in tekstvelden of vrije velden altijd met een cijfer of een letter, tenzij in deze norm expliciet anders gespecificeerd.
2.1.4 Correct gebruik van entiteitenVoor zover elders in de RVB BIM Norm niet nader gespecificeerd, is een entiteit in het BIM-extract gemodelleerd of getekend met de voor het doel geëigende entiteit overeenkomstig het correct beoogd gebruik van de applicatie waarmee het BIM opgezet is. Voorbeeld: wand als wall-object, tekst als text-entiteit, etc.
Het BIM-extract bevat in beginsel geen proxy-objecten:• 2D-BIM-extract: een CAD-tekening mag geen enkel proxy-object bevatten.• 3D-BIM-extract: een IFC-model mag enkel en alleen een proxy-object bevatten conform de
buildingSMART IFC-specificatie, i.e. indien voor het te representeren bouwwerkelement in IFC geen geschikt IFC-object bestaat.
2.1.5 NauwkeurigheidGeometrische entiteiten in het BIM-extract zijn exact gepositioneerd. De entiteiten zijn accuraat, herkenbaar en volledig gemodelleerd of getekend overeenkomstig het vereiste detailleringsniveau, met inachtneming van de eventuele benaderingen die hierbij gebruikelijk van toepassing zijn.
2.1.6 Doublures en doorsnijdingenIn het BIM-extract komen in beginsel geen doublures voor. Er zijn geen BIM-objecten die in eenzelfde BIM-extract op eenzelfde locatie, meermaals hetzelfde representeren, ook al bestaat het BIM-extract uit meerdere aspectmodellen of -tekeningen.
Toelichting: Doublures kunnen ontstaan door tekenkundige of modelleerfouten waarbij foutievelijk meerdere kopieën van een BIM-object op eenzelfde locatie geplaatst zijn. Dergelijke doublures zijn nooit toegestaan. Doublures kunnen ook resulteren uit het disciplinespecifiek concretiseren van bouwwerkelementen. Te denken valt ondermeer aan de bouwwerkelementen in de disciplines bouwkunde en constructie. Bijvoorbeeld een vloerelement in het bouwkundig model kan in het constructiemodel geconcretiseerd zijn in de vorm van een aantal kanaalplaten. Dergelijke doublures zijn enkel en alleen toegestaan als de elementen onderling volledig passend zijn én de elementen eenduidig en consistent in een afzonderlijk aspectmodel of -tekening naar discipline te onderscheiden zijn.
Geheel of gedeeltelijke doorsnijding van BIM-objecten onderling is in beginsel niet toegestaan. Toelichting: Doorsnijdingen van bouwwerkelementen onderling zijn in het algemeen niet toegestaan, zoals bij de aansluiting van wand op wand, wand op vloer, etc. Doorsnijdingen van ondergeschikte aard, zoals deze van ingestorte of ingefreesde elektraleidingen met wanden, zijn toegestaan. Doorsnijding is in ieder geval niet toegestaan bij ontmoetingen van significante installatietechnische elementen met elementen uit de hoofddraagconstructie.
RVB BIM Norm | 10
2.1.7 Modeleenheid (units), maataanduidingen, maateenheden en getalafrondingHet BIM-extract is initieel opgezet gebruik makend van een metrisch sjabloon (template), waarbij 1 modeleenheid (drawing unit) = 1 mm, met weergave van:
• lengtemaat in mm of m,• oppervlaktemaat in m2,• volume in m3.
De waarden van maataanduidingen volgen uit de exacte afmetingen van gemodelleerde of getekende BIM-objecten. Het is niet toegestaan om de waarden handmatig aan te passen en hiermee model afwijkingen te corrigeren. Bij de weergave van maataanduidingen in de BIM-extracten zijn de afrondingsregels van toepassing die voor het bouwinformatieproduct geëigend en gebruikelijk zijn.
2.1.8 Informatie-indelingssystematiek en -naamgevingScheiding van informatie in het BIM-extract gebeurt volgens de systematiek van NL-SfB, gebruikmakend van de NL-SfB variant-elementen nummercodes, zonder haakjes, en bijbehorende omschrijvingen.
De NL-SfB nummercode bestaat uit 4 cijfers. Daar waar het algemene of verzamelniveau gebruikt wordt, wordt de code met één of twee nullen uitgevuld tot een viercijferige code. Het verder uitsplitsen van informatie door toevoeging van cijfers is toegestaan. In de tekst van de NL-SfB omschrijving is het leesteken “;” niet toegestaan en is vervangen door een spatie gevolgd door het koppelteken “-”.
2.1.9 Bouwlaagindeling (levels) en -naamgevingBouwlaag: zie begripsbepaling §1.1.
Toelichting: • De constructieve vloer en de afwerkvloer van een verdieping behoren als onderbegrenzing tot de overeenkomstige bouwlaag.• Een trapbordes of een incidentele tussenverdieping is in beginsel geen afzonderlijke bouwlaag. Waar nodig kunnen
aanvullende (plattegrond-)aanzichten voor dergelijke tussenverdiepingen geproduceerd worden, zonder hierbij af te wijken van de bouwlaagmodelstructuur.
RVB BIM Norm | 11
Notatie van de bouwlaagnaamgeving: <bouwlaagnummer><verdiepingsoort><spatie><tekstuele beschrijving>, waarbij:
• <bouwlaagnummer>: ..., -2, -1, 00, 01, 02, ..., waarbij 00 voorbehouden is voor de bouwlaag met de dominante hoofdtoegang.
• <verdiepingsoort>: - Bij een normale verdieping: code is niet van toepassing (geen karakter). - Bij een incidentele tussenverdieping: code bestaat uit 1 letter, waarbij: - a = 1ste tussenverdieping, - b = 2de tussenverdieping, - etc.• <tekstuele beschrijving>: kelder, begane grond, etc.
Voorbeelden van bouwlaagnaamgeving en aanvullende aanzichten in het geval van een tussenverdieping:
3D-BIM-extract: -2 kelder, -1 kelder, 00 begane grond, 01 eerste verdieping, etc.
2D-BIM-extract:
-2 kelder, -1 kelder, 00 begane grond, 00a tussenverdieping, 01 eerste verdieping, etc.
RVB BIM Norm | 12
2.2 Specificaties van het IFC-model
Naast de algemene vereisten aan BIM-extracten zijn, specifiek voor IFC-modellen, de in dit hoofdstuk gestelde specificaties van toepassing.
2.2.1 Begripsbepaling• IFC-model: 3D-BIM-extract als het totaal van IFC-objecten in één of meerdere IFC-bestanden die voldoen
aan de in de RVB BIM Norm gestelde specificaties. Het IFC-model kan bestaan uit meerdere onderling gecoördineerde deel- of aspectmodellen.
• IFC-object: de entiteit in het IFC-model die ontstaat door de extractie (i.c. export) van het overeenkomstige BIM-object uit het BIM volgens de gestelde IFC specificaties.
• IFC-object-ID: vrij te kiezen, eenvoudig herkenbare en leesbare identificatiecode van het IFC-object, welke uniek is binnen het IFC-model.
• ObjectGUID: GUID (globally unique identifier) van het IFC-object, door de BIM software gegenereerde unieke identificatiecode.
Toelichting: Naargelang de toepassing kan de IFC-object-ID of de ObjectGUID als BIM-object-ID begrepen worden.
2.2.2 Toepassingsgebied• Modelsoort: - DO/bestek (as designed) - Revisiemodel (as built, as maintained)• Disciplines: alle
2.2.3 Normatieve referentiesVoor zover in de RVB BIM Norm niet nader of afwijkend gespecificeerd, zijn de navolgende referenties van toepassing:
• IFC 2x3 TC1: http://buildingsmart-tech.org/ifc/IFC2x3/TC1/html/index.htm• BNA - NL-SfB tabellen 2005 incl. herziene Elementenmethode ’91.• NEN-EN 15221-6: “Facility Management - Part 6: Area and Space Measurement in Facility Management”.
2.2.4 Bestandsformaat en -naam• Bestandsformaat: IFC 2x3 TC1• Bestandsnaam: <projectnaam>_<aspectmodelsoort>
2.2.5 OpleveringsvereistenEr zijn geen bijkomende opleveringsvereisten, anders dan dat het aangeleverde IFC-model in IFC-formaat voldoet aan de in de RVB BIM Norm gestelde algemene en specifieke vereisten.Toelichting: • Het is toegestaan dat het IFC-model meer bouwwerkinformatiegegevens bevat dan deze die volgens de RVB BIM Norm
minimaal vereist zijn.• Zie §3 voor de bij de BIM-extracten aan te leveren bestanden.
RVB BIM Norm | 13
2.2.6 IFC-modelHet IFC-model voldoet aan de hierna genoemde specificaties.
2.2.6.1 Geometrisch detailleringsniveauVoor zover elders in de RVB BIM Norm niet nader gespecificeerd, hebben geometrische IFC-objecten tenminste de herkenbare driedimensionale vorm en grootte zoals ze in hun uiterlijke vorm in de werkelijkheid verschijnen met een detailleringsniveau dat toereikend is voor de modelsoorten:
• DO/bestek (as designed) • Revisiemodel (as built, as maintained)
Toelichting: • Bijvoorbeeld een wandpakket samengesteld uit verschillende materiaallagen is in het IFC-model tenminste door de
geometrie van haar uiterlijke vorm weergegeven: dit is ter plaatste van het wandvlak de buitenzijde van de afgewerkte laag.• De aanleverende partij is zelf verantwoordelijk dat de uiterlijke verschijningsvorm en de bijhorende alfanumerieke informatie
van IFC-objecten overeenstemt met deze van de BIM-objecten in het BIM-bronbestand.
2.2.6.2 Informatie-indeling (classification)Tenminste alle IFC-objecten die een geometrische representatie van materiële bouwwerkelementen zijn, hebben een correcte IfcClassificationReference volgens de voorgeschreven naamgeving van de BIM-extracten: zie §2.1.8. De cijferparen van de NL-SfB nummercode zijn gescheiden door een punt “.”. Toegevoegde cijferparen zijn tevens met een punt gescheiden van de viercijferige NL-SfB code.
Attributes: • ItemReference: <NL-SfB nummercode>
Voorbeelden: 22.11 22.00 22.13.12
• Name: <NL-SfB omschrijving> Voorbeeld: binnenwanden - niet constructief - massieve wanden
2.2.6.3 ObjectrelatiesVoor zover elders in de RVB BIM Norm niet nader gespecificeerd, hebben de IFC-objecten onderlinge relaties conform de buildingSMART IFC-specificatie. Voor zover van toepassing hebben IFC-objecten tenminste een correcte IfcRelContainedInSpatialStructure-relatie.
Voorbeeld: Het meubel behoort tot de ruimte, de ruimte behoort tot de bouwlaag, de bouwlaag behoort tot het bouwwerk.
2.2.6.4 ObjectGUIDBij een actualisering of revisering van het IFC-model behoudt in beginsel elk IFC-object haar oorspron-kelijke GUID.
2.2.6.5 Geografische positie en oriëntatieHet IFC-model is geografisch correct georiënteerd en gepositioneerd volgens WGS84 en NAP.
Toelichting: • Denk hierbij aan de geografische positie van het terreinobject en de geografische oriëntatie (TrueNorth) van het
projectobject.• De geografische positie en oriëntatie is onderscheiden van de lokale positie en oriëntatie: zie §2.1.2.
RVB BIM Norm | 14
2.2.7 IFC-objectenHet IFC-model omvat, voor zover van toepassing, tenminste alle hierna genoemde IFC-objecten.
2.2.7.1 Project• Beschrijving: het project is het IFC-object met project- en modelinformatie.• Relaties: het IFC-model omvat slechts één projectobject.• IfcObject: IfcProject
Attributes: • Name: <projectnaam> • RepresentationContexts: het project is geografisch correct georiënteerd, door opgave van de
TrueNorth-waarde. • UnitsInContext: zie §2.1.7.
2.2.7.2 Terrein• Beschrijving: het terrein, de topografische site van het project.• Geometrie: 3D
Het IFC-object heeft de driedimensionale vorm en afmetingen van tenminste het terreinoppervlak van het project:
- Contour: tenminste van het kadastrale perceel of het geheel van percelen. - Hoogte: volgens de plaatselijke topografie.• Locatie: het referentiepunt van het terrein in het IFC-model is geografisch correct gepositioneerd.• Relaties: het project omvat slechts één terreinobject.• IfcObject: IfcSite
Attributes: • Name: <kadastrale aanduiding>
Voorbeeld: Delft AB 1234 Indien het project zich over meerdere kadastrale percelen uitstrekt, zijn alle kadastrale aanduidingen opgegeven, onderling gescheiden door <spatie>“-”<spatie>. Voorbeeld: Delft AB 1234 - Delft AB 1235
• RefLatitude: geografische locatie, breedtegraad op referentiepunt volgens WGS84. • RefLongitude: geografische locatie, lengtegraad op referentiepunt volgens WGS84. • RefElevation: geografische locatie, peil op referentiepunt, hoogtepeil t.o.v. NAP.
2.2.7.3 Bouwwerk• Beschrijving: zie begripsbepaling §1.1.• Relaties: - Eén of meerdere bouwwerken bevinden zich op het terrein. - Het bouwwerk is correct gepositioneerd t.o.v. het terrein.• Bijzonderheden: bouwwerken met onderling beduidend afwijkende bouwlaagindelingen bevinden zich
in beginsel in afzonderlijke, doch onderling gecoördineerde, IFC-modellen.• IfcObject: IfcBuilding
Attributes: • Name: <RVB-gebouwnummer>
Voorbeeld: 123456A78 Indien het project meerdere RVB-gebouwnummers omvat, zijn alle RVB-gebouwnummers opgegeven, onderling gescheiden door <spatie>“-”<spatie>. Voorbeeld: 123456A78 - 123456A79
RVB BIM Norm | 15
2.2.7.4 Bouwlaag• Beschrijving: zie begripsbepaling §1.1.• Relaties: - Een bouwwerk omvat tenminste één bouwlaag. - Ieder geometrisch IFC-object behoort tot de toepasselijke bouwlaag, met inbegrip van de onderlinge
hiërarchische relatie tussen de IFC-objecten.• IfcObject: IfcBuildingstorey
Attributes: • Name: zie §2.1.9.
Voorbeelden: -1 kelder, 00 begane grond, 01 eerste verdieping, etc.
2.2.7.5 Bouwlaagoppervlakobject• Beschrijving: het Bouwlaagoppervlakobject is het geometrische IFC-object dat expliciet de verzameling
weergeeft van de bij een bouwlaag behorende bouwwerkelementen. Het onderscheid naar binnen- of buitengebied wordt eveneens expliciet gemaakt door de betreffende verzamelingen met afzonderlijke Bouwlaagoppervlakobjecten weer te geven. Toelichting: Materiële bouwwerkelementen die de binnenruimten als omhulling begrenzen van de buitenruimte, zoals de gevel, behoren tot de verzameling van de binnenruimten.
• Geometrie: 2,5D/3D - Contour: bepaling van de omhullende begrenzing op basis van de principes van Level Area volgens
NEN-EN 15221-6. - Hoogte: van de bijbehorende bouwlaag.• Relaties: - Een bouwlaag heeft tenminste één Bouwlaagoppervlakobject. - Bouwlaagoppervlakobjecten mogen elkaar niet doorsnijden. - Een Bouwlaagoppervlakobject omsluit in beginsel geheel alle ruimten die tot de betreffende
bouwlaag behoren, uitgesplitst in hetzij uitsluitend binnenruimten, hetzij uitsluitend buitenruimten. Toelichting: Zowel het Bouwlaagoppervlakobject als de ruimte worden in het IFC-model met een IfcSpace gerepresenteerd. De genoemde relatie is een expliciet toegestane doorsnijding tussen de beide IFC-objecten.
- Ieder Bouwlaagoppervlakobject behoort tot de toepasselijke bouwlaag.• Classificatie: - n.v.t.• Opmerkingen: - De oppervlakte van een Bouwlaagoppervlakobject is geen Bruto Vloeroppervlakte (BVO) volgens NEN 2580. • IfcObject: IfcSpace
Attributes: • Name: de tekst “Gross” komt in de naam voor.
2.2.7.6 Ruimte• Beschrijving: de ruimte is het driedimensionale IFC-object dat in beginsel begrensd is door de haar
omhullende materiële bouwwerkelementen (wanden, vloeren etc.) en in haar vorm op deze omhullende elementen aansluit. Een ruimte is hetzij een binnenruimte, hetzij een buitenruimte.
• Geometrie: 3D - Contour:
In het algemeen volgt de contour van het driedimensionale object op vloerniveau de netto-contour van de ruimte langs de binnenzijde van de omhullende bouwwerkelementen. Interne bouwwerk-elementen, zoals kolommen, zijn ongeacht hun grootte als inwendige contour van het ruimteobject uitgesloten.
- Bij een ruimte in een trappenhuis, liftschacht of installatieschacht wordt in beginsel de netto-contour van de koker aangehouden.
- Indien wet- en regelgeving dit vereist, mag een ruimte waar nodig opgesplitst worden afwijkend van de materiële omhullende bouwwerkelementen.
RVB BIM Norm | 16
- Hoogte: In het algemeen is de hoogte van het driedimensionale object de netto-hoogte van de ruimte, gemeten vanaf de bovenzijde van de afgewerkte vloer tot aan de onderzijde van het element dat de ruimte aan de bovenzijde begrenst.
- Voor binnenruimten: de bovenbegrenzing van de ruimte is doorgaans de onderzijde van het (verlaagd) plafond. Een ruimte kan een variërende hoogte hebben binnen dezelfde bouwlaag, maar kan ook lokaal of in haar geheel een hoogte hebben die de bouwlaaghoogte overstijgt, bijvoorbeeld door het ontbreken van (delen van) een vloer of door vloeropeningen. Bouwlaagoverstijgende ruimten worden per bouwlaag opgesplitst ter hoogte van het bijbehorende bouwlaagniveau. De ruimtedelen sluiten in verticale zin op elkaar aan.
- Voor buitenruimten: bij het ontbreken van een materiële begrenzing aan de bovenzijde is de hoogte van de ruimte deze van de bouwlaag waartoe de ruimte behoort.
• Relaties: - Het bouwwerk is geheel voorzien van ruimten. - Ruimten doorsnijden elkaar niet. - Ruimten liggen steeds geheel binnen de contour van het Bouwlaagoppervlakobject.
Toelichting: Zowel de ruimte als het Bouwlaagoppervlakobject worden in het IFC-model met een IfcSpace gerepresenteerd. De genoemde relatie is evenwel een expliciet toegestane doorsnijding tussen de beide IFC-objecten.
- Iedere ruimte behoort tot de toepasselijke bouwlaag, dit is de bouwlaag waartoe het onderste begrenzende bouwwerkelement, in het algemeen de vloer, van de ruimte behoort. Ieder afzonderlijk ruimtedeel van een bouwlaagoverstijgende ruimte wordt toegekend aan de op die hoogte bijbehorende bouwlaag.
• Classificatie: - n.v.t.• Bijzonderheden: - Wordt niet als ruimte beschouwd: een bouwkundige spouw, de tussenruimte tussen een verlaagd
plafond en een vloer.• IfcObject: IfcSpace
Attributes: - Name: <IFC-object-ID> - ObjectType: ruimtefunctie volgens vigerend bouwbesluit.
Waarde uit vaste keuzelijst in bijlage: §4.1.1. Voorbeeld: verblijfsruimte
- LongName: <ruimtefunctienaam> Vrij te kiezen tekst, doch naam gevoerd volgens de algemene vereisten: zie §2.1.3. Voorbeeld: kantoorruimte
- InteriorOrExteriorSpace: [INTERNAL/EXTERNAL] volgens vigerend bouwbesluit. - BoundedBy: IfcRelSpaceBoundary: De 2nd level space boundary van de ruimte is gegenereerd. 2.2.7.7 Groepering van ruimten: zones• Beschrijving: een zone is een groepering van ruimten of ruimtedelen. Een ruimte kan behoren tot geen,
één of meerdere zones. Toelichting: Een groepering maakt het mogelijk om ruimten of ruimtedelen op een expliciete wijze in het model te clusteren en hiermee op verzamelniveau aanvullende informatie toe te kennen aan iedere ruimte die behoort tot een zone.
• IfcObject: IfcZone
Attributes - Name: code van groep, volgens de respectievelijke groepering zoals hieronder beschreven. - ObjectType: type groepering, volgens de respectievelijke groepering zoals hieronder beschreven.
RVB BIM Norm | 17
Toelichting: Voor bepaalde groeperingen van ruimten is in de notatie van de naamgeving een “<volgnummer>” vereist. Dit volgnummer is nodig om binnen een type groepering, zoals bijvoorbeeld “Bouwbesluit verblijfsgebied”, gelijknamige groepen van ruimten van elkaar te onderscheiden. In het bouwwerk kunnen er immers meerdere verblijfsgebieden zijn die elk afzonderlijk naar oppervlakte meetbaar moeten zijn en zodoende ook als individuele groep van elkaar te onderscheiden moeten zijn.
De volgende groeperingen worden onderscheiden:
• Groepering van ruimtedelen: Ruimten kunnen om velerlei redenen horizontaal of verticaal opgesplitst zijn in afzonderlijke ruimtedelen. Bijvoorbeeld wordt een bouwlaagoverstijgende ruimte opgesplitst in de ruimtedelen per bouwlaag. De geometrisch afzonderlijke ruimtedelen worden vervolgens gegroepeerd zodat steeds de complete ruimte als verzameling van de betreffende ruimtedelen te onderscheiden is.
- Name: <IFC-object-ID> van het dominante ruimtedeel binnen de groepering. In het geval van een ruimtedeel behorende tot een bouwlaagoverstijgende ruimte, zal het ruimtedeel met de materiële onderbegrenzing als het dominante ruimtedeel beschouwd worden. De <IFC-object-ID> van dit ruimtedeel wordt als naam van de groepering gebruikt.
- ObjectType: waarde = “ruimtegroep”
• Bouwbesluit gebruiksfunctie: - Name: gebruiksfunctie volgens vigerend bouwbesluit.
Notatie: GF_<code1>.<code2> waarbij,
- <code1>: code1 uit vaste keuzelijst in bijlage: §4.1.2. - <code2>: code2 uit vaste keuzelijst in bijlage: §4.1.2.
Voorbeeld: Een ruimte behorend tot de kantoorfunctie wordt genoteerd als: GF_05.0 Indien een ruimte volgens het vigerend bouwbesluit voldoet aan de definitie gemeenschappelijk, is in de notatie van elk van de van toepassing zijnde gebruiksfuncties het achtervoegsel “_GM” toegevoegd. Voorbeeld: Een gemeenschappelijke ruimte, in dienst van een kantoorfunctie én een bijeenkomstfunctie, behoort tot de groepen: GF_05.0_GM én GF_01.0_GM. In datzelfde bouwwerk behoren de niet gemeenschappelijke ruimten met een kantoorfunctie tot de groep: GF_05.0. De niet gemeenschappelijke ruimten met een bijeenkomstfunctie behoren tot de groep: GF_01.0. Indien een ruimte volgens het vigerend bouwbesluit voldoet aan de definitie gezamenlijk, is - analoog met het voorgaande - in de notatie van elk van de toepasselijke gebruiksfuncties het achtervoegsel “_GZ” toegevoegd. Indien een ruimte volgens het vigerend bouwbesluit een nevenfunctie vervult, behoort de ruimte zowel tot een groep met de “hoofd”gebruiksfunctie als tot een groep met de “neven”gebruiksfunctie. De groep, die een nevenfunctie vervult, heeft het achtervoegsel “_N”.
- ObjectType: waarde = “gebruiksfunctie”
• Bouwbesluit gebruiksgebied: - Name: gebruiksgebied volgens vigerend bouwbesluit.
Notatie: GG_<code>_<volgnummer> waarbij,
- <code>: code uit vaste keuzelijst in bijlage: §4.1.3. - <volgnummer>: 01, 02, 03, etc. Voorbeeld: GG_G_01 - ObjectType: waarde = “gebruiksgebied”
RVB BIM Norm | 18
• Bouwbesluit verblijfsgebied: - Name: verblijfsgebied volgens vigerend bouwbesluit.
Notatie: VG_<code>_<volgnummer> waarbij,
- <code>: code uit vaste keuzelijst in bijlage: §4.1.4. - <volgnummer>: 01, 02, 03, etc. Voorbeeld: VG_V_01 - ObjectType: waarde = “verblijfsgebied”
Pset_SpaceOccupancyRequirements: - OccupancyNumberPeak: volgens vigerend bouwbesluit het aantal personen dat maximaal
gelijktijdig in het verblijfsgebied aanwezig is.
• Bouwbesluit brandcompartimentering: - Name: (beschermd) (sub)brandcompartiment volgens vigerend bouwbesluit.
Notatie: BC_<code>_<volgnummer> waarbij,
- <code>: code uit vaste keuzelijst in bijlage: §4.1.5. - <volgnummer>: 01, 02, 03, etc. Voorbeeld: BC_BC_01 - ObjectType: waarde = “brandcompartiment”
• Bouwbesluit vluchtroute: - Name: vluchtroute volgens vigerend bouwbesluit.
Notatie: VR_<code>_<volgnummer> waarbij,
- <code>: code uit vaste keuzelijst in bijlage: §4.1.6. - <volgnummer>: 01, 02, 03, etc. Voorbeeld: VR_bVR_01 - ObjectType: waarde = “vluchtroute”
2.2.7.8 Bouwkundige, constructieve en installatietechnische elementen• Beschrijving: de materiële bouwwerkelementen die deel uitmaken van het gebouw: bouwkundige,
constructieve en installatietechnische elementen.• Geometrie: 3D
Zie IFC-modelspecificaties (Geometrisch detailleringsniveau): §2.2.6.1. De elementen zijn in beginsel per bouwlaag gemodelleerd.
• Relaties: ieder bouwwerkelement behoort tot de toepasselijke bouwlaag.• Classificatie: - zie §2.2.6.2.• Bijzonderheden: - elementen in de discipline bouwkunde hebben een materiaaltoekenning.
IfcMaterial: vrij te kiezen materiaalnaam, doch naam gevoerd volgens de algemene vereisten van BIM-extracten én consistent toegepast in het IFC-model.
- deuren en ramen hebben een correcte representatie van de draairichting (operation type) en zijn gedefinieerd met de toepasselijke IfcDoorStyle of IfcWindowStyle.
• IfcObject: ieder bouwwerkelement wordt correct en consistent gerepresenteerd met het geschikte IfcObject: IfcBuildingElement (IfcBeam, IfcColumn, IfcDoor, IfcSlab, IfcWall, IfcWindow, etc.), IfcDistributionElement, IfcElectricalElement, IfcTransportElement, etc.
Attributes: - Name: <IFC-object-ID> • Pset_###Common: voor zover de eigenschap van toepassing is bij het betreffende modelobject: - IsExternal: [True/False]
RVB BIM Norm | 19
2.2.7.8.1 Aspect brandveiligheid• Pset_###Common: voor zover de eigenschap van toepassing is bij het betreffende modelobject: - FireRating: weerstand tegen branddoorslag en brandoverslag, WBDBO waarde volgens vigerend
bouwbesluit (in minuten). Het betreft de werkelijke WBDBO waarde, niet de gestelde eis. Voorbeeld: 60
- Compartmentation: [True/False] o.a. van toepassing bij IfcWall
Specifiek voor een IFC-object dat toegang tot een ruimte verschaft (zoals een deur), zijn aanvullend de volgende eigenschappen van toepassing:• Pset_###Common - FireExit: [True/False]: de waarde “True” is toegekend aan alle elementen die een uitgang voor
ontvluchting zijn, zoals bepaalde deuren. - SelfClosing: [True/False] - SmokeStop: [True/False]
2.2.7.8.2 Discipline constructie• Pset_###Common: voor zover de eigenschap van toepassing is bij het betreffende modelobject: - LoadBearing: [True/False]: de waarde “True” is toegekend aan alle elementen die constructief
dragend zijn.• alle elementen in de discipline constructie zijn ook in hun constructief analytische weergave in het
IFC-model aanwezig met hun toepasselijke krachtswerking. IfcStructuralItem (ItcStructuralMember, IfcStructuralConnection) IfcStructuralActivity (IfcStructuralAction, IfcStructuralReaction)
2.2.7.9 Groepering van constructieve elementen IfcStructuralLoadGroup is toegepast voor de groepering van belastingcombinaties.
IfcStructuralAnalysisModel is toegepast als systeem voor het constructieve analytische model.
2.2.7.10 Groepering van installatietechnische elementen IfcElectricalCircuit is toegepast als systeem voor de stroomdistributie elementen.
2.2.7.11 Inventaris-, inrichtings- en uitrustingselementen• Beschrijving: inventaris, inrichtings- en uitrustingselementen.• Geometrie: zie IFC-modelspecificaties (Geometrisch detailleringsniveau): §2.2.6.1.• Relaties: - Ieder element behoort tot de toepasselijke bouwlaag. - Voor zover een element in een ruimte gelegen is, behoort het element tot de haar omhullende
ruimte.• Classificatie: - zie §2.2.6.2.• IfcObject: ieder element wordt correct en consistent gerepresenteerd met het geschikte IfcObject
(IfcFurnishingElement, IfcEquipmentElement, etc.). Attribute: - Name: <IFC-object-ID>
RVB BIM Norm | 20
2.3 Specificaties van de CAD-tekening
Naast de algemene vereisten aan de BIM-extracten zijn, specifiek voor CAD-tekeningen, de in dit hoofdstuk gestelde specificaties van toepassing.
2.3.1 Begripsbepaling• CAD-tekening: 2D-BIM-extract als het totaal van tekeningbladen met CAD-entiteiten in een
CAD-bestand dat voldoet aan de in de RVB BIM Norm gestelde CAD-specificaties.• tekeningblad: het blad in de CAD-tekening met het tekeningkader waarbinnen het titelblok samen
met bijvoorbeeld een renvooi, overzichtstekening, een viewport of andere entiteiten geplaatst zijn. Het tekeningblad is bestemd voor weergave op een digitaal of papieren document.
2.3.2 Toepassingsgebied• Tekenwerksoort: - DO/bestek (as designed) - Revisietekenwerk (as built, as maintained)• Disciplines: alle
2.3.3 Normatieve referentiesOnderstaande referenties zijn integraal van toepassing tenzij anders aangegeven. Voor zover inhoudelijk overlappend, prevaleert de eerstgenoemde norm of referentie. In alle gevallen prevaleert hetgeen dat in de RVB BIM Norm gespecificeerd is.
• BNA - NL-SfB tabellen 2005 incl. herziene Elementenmethode ’91.• GB CAS 4.0 “GB CAD Afsprakenstelsel 4”. - De bepalingen onder §2 zijn optioneel. - Inclusief de in §5 en §6 genoemde voorkeuren.• NEN-ISO 128-40:2001 “Technische tekeningen -- Algemene principes voor de weergave -- Deel 40:
Basisafspraken voor doorsneden”. - De bepalingen onder NEN-ISO 128-50:2001 §9 zijn niet van toepassing.• NEN-ISO 5455:1990 & /C1:1996 “Technische tekeningen -- Schalen”.• NEN-EN-ISO 5457:1999 & /A1:2010 “Technische product-documentatie -- Formaten en inrichting van
tekenbladen”. - Inclusief de in §3.1 genoemde voorkeuren. - De bepalingen onder §4.3, §4.4, §4.5 zijn optioneel. - De bepalingen onder NEN-EN-ISO 7200:2004 §5 zijn optioneel.• NEN 1413 “Symbolen voor veiligheidsvoorzieningen op bouwkundige tekeningen en in bouwkundige
schema’s”.• NEN 2302:1983 “Tekeningen in de bouw -- Algemene regels”. - De bepalingen onder §2.7.1 zijn optioneel. - Inclusief de in §5.1.1 genoemde voorkeuren.• NEN 2574:1993 “Tekeningen in de bouw -- Indeling van gegevens op tekeningen voor gebouwen”.• NPR 2570:1986 “Tekeningen in de bouw -- Coördinatie van gegevens op tekeningen voor gebouwen”. - Uitsluitend §2.
2.3.4 Bestandsformaat en -naam• Bestandsformaat: - DWG 2007: het bestand dient opzichzelfstaand in de courante versie van Autodesk AutoCAD bruikbaar
te zijn, zonder bijvoorbeeld toegevoegde applicaties of bibliotheken. Toelichting: Trusted DWG is geen vereiste, maar het bestand is inhoudelijk geheel compatibel met de courante versie van Autodesk AutoCAD.
- PDF/E: alle bijbehorende fonts zijn embedded aanwezig.• Bestandsnaam: in beginsel vrij te kiezen.
Bij plattegronden vangt de bestandsnaam aan met de bouwlaagnaamgeving, zoals vereist volgens de algemene vereisten van BIM-extracten: zie §2.1.9.
RVB BIM Norm | 21
2.3.5 OpleveringsvereistenDe CAD-tekening en bijbehorende tekeningbladen worden respectievelijk in DWG- én PDF-formaat aangeleverd. Ze voldoen aan de in de RVB BIM Norm gestelde algemene en specifieke vereisten. Bij oplevering van de CAD-tekening:• is de tekening volledig opgeschoond;
Toelichting: Denk hierbij ondermeer aan het verwijderen van hulplijnen of overbodige lijnen afkomstig van extractie uit 3D-geometrie die de leesbhaarheid van entiteiten in de tekening verstoren, denk ook aan het gebruik van een functie zoals “purge”.
• zijn in de tekening geen toegevoegde entiteiten aanwezig zoals OLE-objecten, dictionaries, rasterbe-standen, external references, LISP- of VBA-routines, hyperlinks, databasekoppelingen: zie ook: §2.1.4 m.b.t. proxy-objecten;
• is layer 0 ingesteld als de current layer;• zijn aan de layout tabs geen printer- of plotterdefinities gekoppeld;• zijn alle layout tabs weergegeven als zoom extents;• is de system variable MEASUREMENT ingesteld op 1.Toelichting: Zie §3 voor de bij de BIM-extracten aan te leveren bestanden.
2.3.6 CAD-entiteiten• Er zijn slechts één- en tweedimensionale entiteiten getekend in het xy-vlak van het WCS.• Repeterende elementen zijn waar mogelijk en gebruikelijk gedefinieerd als een block. - Binnen een renvooi zijn geen blocks toegepast.• De elevation, z-waarde, thickness, linewidth, en global width van entiteiten zijn 0 of default (waarbij default
ingesteld is op 0). Eigenschappen van entiteiten zijn by Layer of by Entity.
2.3.7 CAD-tekeningDe CAD-tekening voldoet aan de hierna genoemde specificaties.
2.3.7.1 TekeningbladDe tekeningbladen in de CAD-tekening voldoen aan de volgende vereisten:• Wanneer gevisualiseerd naar (virtueel) papier van het bedoelde formaat zijn de tekeningen, en in het
bijzonder de linetypes en materiaalaanduidingen daarin, goed zichtbaar en te onderscheiden.• Lijndikte wordt slechts bepaald door koppeling aan kleur.• Elk tekeningblad is voorzien van één titelblok (identificatiestrook). Het titelblok bevat de gegevens
gespecificeerd in de bijlage §4.2.
2.3.7.2 DetailleringsniveauHet detailleringniveau is minimaal conform fase bestek (volgens NEN 2574). Naargelang discipline of aspect voldoen de tekeningen aan de volgende aanvullende vereisten:
2.3.7.2.1 Discipline bouwkundeAlle in het werk te realiseren (as designed) of gerealiseerde (as built) bouwwerkelementen zijn getekend. Minimaal gaat het hierbij om de volgende bouwwerkelementen:• Wanden, vloeren, en daken; inclusief de plaatselijke onderbrekingen daarin (vides, sparingen, etc.);• Wand-, vloer-, en dakopeningen (deuren, ramen, luiken, daklichten, rook/warmteafvoer, etc.) inclusief
globale representatie van vulling (kozijn, raamhout, profielen, etc.) en draairichting van eventueel beweegbare of bewegende delen in de vorm van een straalboog of bewegingsrichting in de vorm van een pijl.
• Wandafwerkingen die vanwege wet- en regelgeving zijn voorzien van een attest of certificaat, inclusief materiaalaanduiding.
- De tekst in het renvooi komt overeen met de materiaalnaam of aanduiding in het attest of certificaat.• Verticale verkeersvoorzieningen (trappen, hellingen, liften, etc.), waar gebruikelijk voorzien van een pijl
in de stijgrichting;• Balustrades en leuningen;• Vaste voorzieningen (keukens, sanitair, kasten, etc.).
RVB BIM Norm | 22
2.3.7.2.2 Discipline constructie• Voor deze discipline is het bestaande wettelijk kader het eerste uitgangspunt. Minimaal zijn alle
bouwwerkelementen van de hoofddraagconstructie getekend. • Op tekening is afleesbaar: - Het onderscheid tussen geprefabriceerd beton en in het werk gestort beton. - Betonkwaliteiten en staalsoorten. - Tijdsduur tot bezwijken, indien bepaald tijdens het ontwerpen van een bouwwerkelement of
materiaal.
2.3.7.2.3 Discipline werktuigbouwkunde• De volgende werktuigbouwkundige bouwwerkelementen zijn getekend: - Brandkleppen; - Brandafsluiters t.b.v. compartimentdoorvoer door een W-installatie; - (nood)Afsluiters van gebouwinstallaties; - (nood)Schakelaar van gebouwinstallaties.
2.3.7.2.4 Discipline elektrotechniek• De volgende elektrotechnische bouwwerkelementen zijn getekend: - Brandafsluiters t.b.v. compartimentdoorvoer door een E-installatie.
2.3.7.2.5 Aspect brandveiligheid• Alle in het werk te realiseren, dan wel gerealiseerde brandveiligheidsvoorzieningen worden getekend.
Minimaal gaat het hierbij om de voorzieningen welke zijn genoemd in de bijlage §4.3 en NEN 1413. - (Beschermde) (sub)brandcompartimenten zijn aangegeven met behulp van compartimentlijnen die
zijn voorzien van eigenschappen zoals opgenomen in §4.3. - Brandveiligheidsvoorzieningen zijn weergegeven met de symbolen zoals opgenomen in §4.3. - Indien brandveiligheidsvoorzieningen hun oorsprong vinden in een andere discipline (bouwkunde,
elektrotechniek, etc.) kan het voorkomen dat een bouwwerkelement of voorziening meerdere malen gerepresenteerd wordt in de set revisietekeningen van een bouwwerk. Dit is toegestaan mits de verschillende representaties onderling niet strijdig zijn.
2.3.7.3 TekeningstructuurDe tekeningen voldoen aan de volgende vereisten:• Plattegronden zijn in beginsel een horizontale doorsnede op 1200 mm boven het vloerpeil van de
desbetreffende bouwlaag. - Als hiermee een tekening ontstaat die niet goed afleesbaar is of tot ongewenste bouwkundige
interpretaties aanleiding geeft, mag het doorsnijdingsvlak op een andere hoogte gelegd worden (ook lokaal). In voorkomende gevallen wordt een verklarende tekst in de tekening opgenomen.
• In aanvulling op het bepaalde in NEN-ISO 128-30 wordt ook de projectie van bouwwerkelementen gelegen vóór (boven) het doorsnijdingsvlak op tekening weergegeven.
• Tekenkundig onderscheid van de ligging van bouwwerkelementen ten opzichte van het doorsnij-dingsvlak is conform het volgende:
- Bouwwerkelementaanzicht: - Lijndikte kleiner dan bij doorsnede; - Lijntype getrokken lijn; - Geen arcering. - Bouwwerkelementdoorsnijding: - Lijndikte groter dan aanzicht en projectie; - Lijntype getrokken lijn; - Arcering. - Bouwwerkelementprojectie: - Lijndikte kleiner dan bij doorsnede; - Lijntype onderbroken lijn; - Geen arcering.
RVB BIM Norm | 23
• Doorsneden van bouwwerkelementen zijn voorzien van materiaalaanduiding met behulp van een arcering.
• Bouwwerkelementen getekend in aanzicht zijn bij noemenswaardige verschillen in afstand (diepte) vanaf het doorsnijdingsvlak voldoende visueel onderscheiden. Het gebruik van een afnemende mate aan detaillering en successievelijk dunnere of lichtere lijntypen heeft hiervoor de voorkeur.
- Hierbij moet gedacht worden aan delen van onderliggende verdiepingen zichtbaar door vloer openingen in een plattegrond, of terugliggende bouwdelen in een doorsnede of aanzicht.
• In aanzichten zijn vlakvullingen en beschaduwingen aangegeven met arceerpatronen.• De onderstaande informatie-elementen zijn aanwezig. - Alle projecties zijn voorzien van: - Stramien, inclusief maataanduidingen, waarmee een referentie ontstaat voor plaatsbepaling van
bouwwerkelementen. - Uitwendige maten van het bouwwerk. - Van elk vloerveld, hoogtemaat van bovenzijde afgewerkte vloer. - De netto doorgangsmaat (hoogte en breedte) van alle wand-, vloer-, en dakopeningen (met name
deuren en doorgangen). - Plattegronden zijn bovendien voorzien van: - Doorsnedeaanduidingen van aanwezige verticale doorsneden. - Voor elke ruimte: tenminste de bijbehorende ruimtefunctienaam als vrij te kiezen tekst, naam
gevoerd volgens de algemene vereisten in §2.1.3, ruimtenummer en oppervlakte. - Doorsneden zijn bovendien voorzien van: - Netto hoogtematen van verdiepingen met tussenliggende en totaalmaten, ten opzichte van het
vastgestelde peil. - Aanzichten zijn bovendien voorzien van: - Hoofdgevelmaten, goothoogten, en nokhoogten, ten opzichte van het vastgestelde peil.• Alle in een tekening voorkomende arceringen, symbolen, en afwijkende linetypes zijn in een renvooi
opgenomen met hun verklaring. - Corresponderende elementen zijn hetzelfde in de renvooien binnen het tekenwerk van één
bouwwerk. - Linetypes voor stramienlijnen, afbreeklijnen, en bouwwerkelementprojecties hoeven niet opgenomen
te worden. - Indien noodzakelijk voor een goed begrip kan een afwijkend linetype voorzien worden van een
verklarende tekst in de tekening in modelspace. - Voor symbolen mag conform NEN 2302 §4.3 worden volstaan met een verwijzing naar een staat of
norm.• Wanneer binnen een tekening slechts een onderdeel van een bouwwerk (bijvoorbeeld een bouwdeel,
een ruimte of een detail) afgebeeld wordt, dan is er een overzichtstekening die duidelijk maakt waar het desbetreffende onderdeel zich bevindt binnen het totaal te realiseren of gerealiseerde bouwwerk. Een overzichtstekening bevat bijvoorbeeld de volgende informatie:
- een schematische situatietekening, - een schematische plattegrond van het bouwwerk waarop het totaal en het beschouwde deel is
aangegeven; - een schematische doorsnede van het bouwwerk waarop verdieping of kijkrichting is aangegeven.• Schrift in de tekeningen is gesteld in de Nederlandse taal.
2.3.7.3.1 Aspect brandveiligheidTekeningen voor het aspect brandveiligheid voldoen aan de volgende aanvullende vereisten:• De corresponderende bouwkundige tekening is als ‘onderlegger’ toegevoegd, als enkel block welke zich
op layer 0 bevindt.• Ieder symbool (met uitzondering van compartimentlijnen) bestaat uit een block met de inhoud en
eigenschappen zoals voorgeschreven in bijlage §4.3. • Compartimentlijnen bestaan uit een polyline met de in bijlage §4.3 voorgeschreven eigenschappen.
RVB BIM Norm | 24
2.3.7.4 Informatielaagindeling (layers) en -naamgevingScheiding van informatie gebeurt door plaatsing van entiteiten op layers. Entiteiten in de tekeningen zijn geplaatst op de toepasselijke layer met de laagnaamgeving volgens de voorgeschreven naamgeving van de BIM-extracten: zie §2.1.8. Notatie van de laagnaamgeving: <NL-SfB nummercode><spatie><NL-SfB omschrijving>
Voorbeelden: 2200 binnenwanden2210 binnenwanden - niet constructief
2.3.7.4.1 Aspect brandveiligheidTekeningen voor het aspect brandveiligheid voldoen aan de volgende aanvullende vereisten:• Alle getekende brandveiligheidsinformatie, zoals symbolen en lijnen zijn geplaatst op de layer met code
6510.• Compartimentlijnen hebben de bijbehorende eigenschappen in het achtervoegsel van de laagnaam-
geving gecodeerd, volgens het format TTT_EIW_SX_B_SN waarbij: - TTT = Tijd in minuten (3 karakters); - EIW = kwaliteitsaanduiding (3 karakters); - SX = rookwerendheid (2 karakters); - B = Brandklasse (1 karakter); - SN = Rookklasse (2 karakters). De velden komen overeen met de eigenschappen van het symbool compartimentscheiding (symbool
6.4.16 volgens NEN 1413). Indien een karakter met leeg of afwezig geduid moeten worden, wordt een nul “0” voor dit karakter gebruikt.
RVB BIM Norm | 25
2.4 Specificaties van de meetstaten, berekeningen, uittrekstaten
Naast de algemene vereisten aan de BIM-extracten zijn, specifiek voor meetstaten, berekeningen, uittrekstaten, e.d. de in dit hoofdstuk gestelde specificaties van toepassing.
2.4.1 Begripsbepaling-
2.4.2 Toepassingsgebied• Productsoort: - DO/bestek (as designed) - Revisie (as built, as maintained)• Disciplines: alle
2.4.3 Referenties-
2.4.4 Bestandsformaat en -naam• Bestandsformaat: toepasselijk bestandsformaat indien elders niet nader gespecificeerd.• Bestandsnaam: vrij te kiezen indien elders niet nader gespecificeerd.
RVB BIM Norm | 26
Bij de aanlevering van BIM-extracten worden ook de onderstaande bestanden aangeleverd.
3.1 Algemeen
3.1.1 BIM• BIM-bronbestand en de daarmee samenhangende bestanden die benodigd zijn om het geleverde extract
compleet en op eenvoudige en herhaalbare wijze te reproduceren. Toelichting: Het BIM kan ook bestaan uit meerdere afzonderlijke modellen die onderling gecoördineerd zijn.
• Bestandsformaat: vrij te kiezen, in origineel (merkspecifiek) bronbestandsformaat.• Bestandsnaam: vrij te kiezen.
3.1.2 Modeldocumentatie • Logboek met beschrijving van: - Noemenswaardige modelleerkeuzes, -afspraken, etc. - Instructie om op eenvoudige en herhaalbare wijze alle extracten uit het BIM te reproduceren. - BIM-applicatie- en systeemgegevens: softwarenaam en -versie, besturingssysteem en -versie.• Bestandsformaat: Word of ODF• Bestandsnaam: <projectnaam>_modeldocumentatie
3.1.3 Bestandenlijst• Lijst van de aangeleverde bestanden (incl. contextspecifieke bestanden: zie §3.2) met vermelding van de
bestandsnamen, -formaten, formaatversies en beknopte beschrijvingen van de bestandsinhoud. In de lijst is ook de aangeleverde mappenstructuur toegelicht.
- Specifiek voor CAD-tekeningen: de lijst omvat ook een tekeninglijst met daarin de gegevens zoals aangegeven in bijlage §4.2. Deze gegevens corresponderen met de gegevens in het titelblok.
- Daar waar het bijkomende of niet uit het BIM geëxtraheerde bestanden betreft, zoals bijvoorbeeld constructieve berekeningen of materiaalcertificaten, zijn deze via het BIM-object-ID aan het bijbehorende bouwwerkelement gekoppeld, minstens in de bestandenlijst of in een aparte relatietabel.
• Bestandsformaat: Excel of ODS• Bestandsnaam: <projectnaam>_bestandenlijst
3. Bij de BIM-extracten te leveren bestanden
RVB BIM Norm | 27
3.2 Contextspecifiek
Naargelang de specifieke context, zoals de aard van het contract of project, waarbij het aanleveren van BIM-extracten vereist is, zijn – naast de algemeen bij de BIM-extracten aan te leveren bestanden – ook aanvullende bestanden vereist.
3.2.1 DBFMO, DBM en MC
3.2.1.1 Relatietabel prestatiespecificatiesDe door Opdrachtnemer op te stellen oplossing met de expliciete en ondubbelzinnige koppeling van de functievervuller-IDs aan:• resp. de functie-IDs. Deze relatie kan één op veel zijn. • resp. de identificatielabel-IDs, voor deze functievervullers die ook fysiek identificeerbaar zijn met een
identificatielabel. Deze relatie is één op één. Toelichting: In de prestatiespecificaties is bepaald welke functievervullers een identificatielabel dienen te hebben.
De aan te leveren oplossing is tenminste gelijkwaardig met onderstaande voorbeeldoplossing:• Tabel met de relatiekoppelingen.• Bestandsformaat: Excel of ODS.• Bestandsnaam: <projectnaam>_relatiemodel• Sjabloon: zie bijlage §4.4.
De tabel omvat de expliciete en ondubbelzinnige koppeling van de functievervuller-IDs aan:• resp. de functie-IDs. De koppeling is vastgelegd in relatietabel 1, waarbij: - 1e kolom: functievervuller-IDs - 2e kolom: functie-IDs• resp. de identificatielabel-IDs. De koppeling is vastgelegd in relatietabel 2, waarbij: - 1e kolom: functievervuller-IDs - 2e kolom: identificatielabel-IDs
Schematisch voorbeeld van relatietabel met koppeling van functievervuller-IDs aan functie-IDs
BIM-extract relatietabel prestatiespecificaties
A
F G
E
B C D Func
tieve
rvul
ler-
ID
Func
tie-I
D
A 1.1
B 1.1
C 1.1
D 1.1
E 1.2.2
F
G 1.2.1.1
G 1.2.1.2
functievervullers functies
1.1 Kantooralgemeen
1.2.2Verkeersruimte
1.2.1.1Archief DIV
1.2.1.2Archief inspectie
RVB BIM Norm | 28
De genoemde documenten zijn externe bijlagen beschikbaar op de RVB-website.
4.1 Nomenclatuur Bouwbesluit 2012
Lijst “RVB BIM Norm v1.0 - bijlage - nomenclatuur BB2012” omvat de onderstaande lijsten op de gelijknamige tabbladen.
4.1.1 Ruimtefunctie
4.1.2 Gebruiksfunctie
4.1.3 Gebruiksgebied
4.1.4 Verblijfsgebied
4.1.5 Brandcompartimentering
4.1.6 Vluchtroute
4.2 Titelblok- en tekeninglijstgegevens
Lijst “RVB BIM Norm v1.0 - bijlage - titelblok- en tekeninglijstgegevens”.
4.3 Brandveiligheid: symbolen en lijnen
Lijst “RVB BIM Norm v1.0 - bijlage - brandveiligheid symbolen en lijnen”.
4.4 Relatietabel sjabloon
Lijst “RVB BIM Norm v1.0 - bijlage - relatietabel sjabloon”.
4. Bijlage
RVB BIM Norm | 29
RVB BIM Norm | 30
RVB BIM Norm | 31
Deze brochure is een uitgave van:
Het RijksvastgoedbedrijfKorte Voorhout 7, 2511 CW Den Haagwww.rijksvastgoedbedrijf.nl
Februari 2013
Tuindorp - Zoetermeer
2
Zalmplaatschool - Rotterdam
2
NL-SfB, Elementenmethode '91
Toepassing
Een indeling op bouwdelen is een veel gebruikte manier om een gebouw geordend weer te geven. Bouwdelen
worden gerangschikt volgens een bepaalde methode. De meest gebruikte methode is die van de NL-SfB. De
NL-SfB is een manier van indelen met een eigen codering. De NL-SfB codering heeft zich in Nederland
ontwikkeld tot een standaard op het gebied van elementgerichte classificaties en wordt veel toegepast bij
meerjarenonderhoud. De NL-SfB codering deelt het gebouw op in elementen die elk onder een eigen rubriek
worden geplaatst. Zo vallen bijvoorbeeld alle buitenkozijnen onder de rubriek buitenwandopeningen. Deze
indeling zorgt er echter voor dat onderdelen waar een bouwdeel uit bestaat in verschillende rubrieken kan
vallen.
Historie
De SfB-codering is in de jaren vijftig in Zweden ontwikkeld voor classificatie van gebouwdelen ten behoeve van
kostencalculaties en bestekomschrijvingen. SfB staat voor “Samarbestkommitte Byggnadsfragor”, wat
'samenwerkingscommite voor bouwvraagstukken' betekent. Sinds 1977 is er een Nederlandse SfB-commissie,
die een indelingstabel voor de Nederlandse bouwsector heeft ontwikkeld onder de naam NL-SfB.
De norm wordt in 2015 van de BNA overgedragen op het BIM Loket, deze zal de norm beheren.
Opbouw
De SfB-code, bestaat uit drie delen:
1. Met het eerste deel van de SfB-code wordt verwezen naar het bouwdeel, de plaats waar het product in
het gebouw of het terrein zit. Bijvoorbeeld funderingsconstructies of vloerafwerking.
2. Met het tweede deel wordt verwezen naar de vorm of functie van het product, zoals baanvormige
(dak)bedekking, isolatie of beplanting.
3. Met het derde deel wordt aangegeven waar het product van gemaakt is, bijvoorbeeld van marmer,
linoleum of beton.
Besluit
Dura Vermeer volgt de RvB BIM Norm (artikel 2.1.8) betreft de methode hoe gebouwen gedecomposeerd
moeten worden. Dit wordt gedaan aan de hand van viercijferige code.
Zie voorbeeld:
xx 31.0 Buitenwandopeningen
xx.x 31.2 Buitenwandopeningen; Gevuld met
ramen
xx.xx 32.25 Buitenwandopeningen; Gevuld met
ramen, combinatieramen
Element
Variant-elementgroep
Variant-element
1- FUNDERINGEN 11 bodemvoorzieningen
13 vloeren op grondslag
16 funderingsconstructies
17 paalfunderingen
2- RUWBOUW 21 buitenwanden
22 binnenwanden
23 vloeren
24 trappen en hellingen
27 daken
28 hoofddraagconstructies
3- AFBOUW 31 buitenwandopeningen
32 binnenwandopeningen
33 vloeropeningen
34 balustrades en leuningen
37 dakopeningen
38 inbouwpakketten
4- AFWERKINGEN 41 buitenwandafwerkingen
42 binnenwandafwerkingen
43 vloerafwerkingen
44 trap- en hellingafwerkingen
45 plafondafwerkingen
47 dakafwerkingen
48 afwerkingspakketten
5- INSTALLATIES WERKTUIGBOUWKUNDIG 51 warmte-opwekking
52 afvoeren
53 water
54 gassen
55 koude-opwekking en distributie
56 warmtedistributie
57 luchtbehandeling
58 regeling klimaat en sanitair
6- INSTALLATIES ELEKTROTECHNISCH 61 centrale electrotechnische voorzieningen
62 krachtstroom
63 verlichting
64 communicatie
65 beveiliging
66 transport
67 gebouwbeheervoorzieningen
7- VASTE VOORZIENINGEN 71 vaste verkeersvoorzieningen
72 vaste gebruikersvoorzieningen
73 vaste keukenvoorzieningen
74 vaste sanitaire voorzieningen
75 vaste onderhoudsvoorzieningen
76 vaste opslagvoorzieningen
8- LOSSE INVENTARIS 81 losse verkeersinventaris
82 losse gebruikersinventaris
83 losse keukeninventaris
84 losse sanitaire inventaris
85 losse schoonmaakinventaris
86 losse opslaginventaris
9- TERREIN 90 terrein
1- FUNDERINGEN
11 bodemvoorzieningen
11.10 bodemvoorzieningen; grond, algemeen (verzamelniveau)
11.11 bodemvoorzieningen; grond, ontgravingen
11.12 bodemvoorzieningen; grond, aanvullingen
11.13 bodemvoorzieningen; grond, sloop- en rooiwerkzaamheden
11.15 bodemvoorzieningen; grond, damwanden
11.20 bodemvoorzieningen; water, algemeen (verzamelniveau)
11.24 bodemvoorzieningen; water, bemalingen
11.25 bodemvoorzieningen; water, damwanden
13 vloeren op grondslag
13.10 vloeren op grondslag; niet constructief, algemeen (verzamelniveau)
13.11 vloeren op grondslag; niet constructief, bodemafsluitingen
13.12 vloeren op grondslag; niet constructief, vloeren als gebouwonderdeel
13.13 vloeren op grondslag; niet constructief, vloeren als bestrating
13.20 vloeren op grondslag; constructief, algemeen (verzamelniveau)
13.21 vloeren op grondslag; constructief, bodemafsluitingen
13.22 vloeren op grondslag; constructief, vloeren als gebouwonderdeel
13.25 vloeren op grondslag; constructief, grondverbeteringen
16 funderingsconstructies
16.10 funderingsconstructies; voeten en balken, algemeen (verzamelniveau)
16.11 funderingsconstructies; voeten en balken, fundatie voeten
16.12 funderingsconstructies; voeten en balken, fundatie balken
16.13 funderingsconstructies; voeten en balken, fundatie poeren
16.14 funderingsconstructies; voeten en balken, gevelwanden (-200)
16.15 funderingsconstructies; voeten en balken, grondverbeteringen
16.20 funderingsconstructies; keerwanden, algemeen (verzamelniveau)
16.21 funderingsconstructies; keerwanden, grondkerende wanden
16.22 funderingsconstructies; keerwanden, waterkerende wanden
16.23 funderingsconstructies; keerwanden, gevelwanden (-200)
16.25 funderingsconstructies; keerwanden, grondverbeteringen
17 paalfunderingen
17.10 paalfunderingen; niet geheid, algemeen (verzamelniveau)
17.11 paalfunderingen; niet geheid, dragend palen; geboord
17.12 paalfunderingen; niet geheid, dragende palen; geschroefd
17.13 paalfunderingen; niet geheid, trekverankeringen
17.14 paalfunderingen; niet geheid, pijler-putring-funderingen
17.15 paalfunderingen; niet geheid, bodeminjecties
17.20 paalfunderingen; geheid, algemeen (verzamelniveau)
17.21 paalfunderingen; geheid, dragende palen
17.22 paalfunderingen; geheid, palen; ingeheide bekisting
17.23 paalfunderingen; geheid, trekverankeringen
17.25 paalfunderingen; geheid, damwanden-funderingen
2- RUWBOUW
21 buitenwanden
21.10 buitenwanden; niet constructief, algemeen (verzamelniveau)
21.11 buitenwanden; niet constructief, massieve wanden
21.12 buitenwanden; niet constructief, spouwwanden
21.13 buitenwanden; niet constructief, systeemwanden
21.14 buitenwanden; niet constructief, vlieswanden
21.15 buitenwanden; niet constructief, borstweringen
21.16 buitenwanden; niet constructief, boeiboorden
21.20 buitenwanden; constructief, algemeen (verzamelniveau)
21.21 buitenwanden; constructief, massieve wanden
21.22 buitenwanden; constructief, spouwwanden
21.23 buitenwanden; constructief, systeemwanden
21.25 buitenwanden; constructief, borstweringen
22 binnenwanden
22.10 binnenwanden; niet constructief, algemeen (verzamelniveau)
22.11 binnenwanden; niet constructief, massieve wanden
22.12 binnenwanden; niet constructief, spouwwanden
22.13 binnenwanden; niet constructief, systeemwanden; vast
22.14 binnenwanden; niet constructief, systeemwanden; verplaatsbaar
22.20 binnenwanden; constructief, algemeen (verzamelniveau)
22.21 binnenwanden; constructief, massieve wanden
22.22 binnenwanden; constructief, spouwwanden
22.23 binnenwanden; constructief, systeemwanden; vast
23 vloeren
23.10 vloeren; niet constructief, algemeen (verzamelniveau)
23.11 vloeren; niet constructief, vrijdragende vloeren
23.12 vloeren; niet constructief, balkons
23.13 vloeren; niet constructief, galerijen
23.14 vloeren; niet constructief, bordessen
23.15 vloeren; niet constructief, vloeren t.b.v. technische voorzieningen
23.20 vloeren; constructief, algemeen (verzamelniveau)
23.21 vloeren; constructief, vrijdragende vloeren
23.22 vloeren; constructief, balkons
23.23 vloeren; constructief, galerijen
23.24 vloeren; constructief, bordessen
23.25 vloeren; constructief, vloeren t.b.v. technische voorzieningen
24 trappen en hellingen
24.10 trappen en hellingen; trappen, algemeen (verzamelniveau)
24.11 trappen en hellingen; trappen, rechte steektrappen
24.12 trappen en hellingen; trappen, niet-rechte steektrappen
24.13 trappen en hellingen; trappen, spiltrappen
24.15 trappen en hellingen; trappen, bordessen
24.20 trappen en hellingen; hellingen, algemeen (verzamelniveau)
24.21 trappen en hellingen; hellingen, beloopbare hellingen
24.22 trappen en hellingen; hellingen, berijdbare hellingen
24.25 trappen en hellingen; hellingen, bordessen
24.30 trappen en hellingen; ladders en klimijzers, algemeen (verzamelniveau)
24.31 trappen en hellingen; ladders en klimijzers, ladders
24.32 trappen en hellingen; ladders en klimijzers, klimijzers
24.35 trappen en hellingen; ladders en klimijzers, bordessen
27 daken
27.10 daken; niet constructief, algemeen (verzamelniveau)
27.11 daken; niet constructief, vlakke daken
27.12 daken; niet constructief, hellende daken
27.13 daken; niet constructief, luifels
27.14 daken; niet constructief, overkappingen
27.16 daken; niet constructief, gootconstructies
27.20 daken; constructief, algemeen (verzamelniveau)
27.21 daken; constructief, vlakke daken
27.22 daken; constructief, hellende daken
27.23 daken; constructief, luifels
27.24 daken; constructief, overkappingen
27.26 daken; constructief, gootconstructies
28 hoofddraagconstructies
28.10 hoofddraagconstructies; kolommen en liggers, algemeen (verzamelniveau)
28.11 hoofddraagconstructies; kolommen en liggers, kolom-/liggerconstructies
28.12 hoofddraagconstructies; kolommen en liggers, spanten
28.20 hoofddraagconstructies; wanden en vloeren, algemeen (verzamelniveau)
28.21 hoofddraagconstructies; wanden en vloeren, wand-/vloerconstructies
28.30 hoofddraagconstructies; ruimte-eenheden, algemeen (verzamelniveau)
28.31 hoofddraagconstructies; ruimte-eenheden, doosconstructies
3- AFBOUW
31 buitenwandopeningen
31.10 buitenwandopeningen; niet gevuld, algemeen (verzamelniveau)
31.11 buitenwandopeningen; niet gevuld, daglichtopeningen
31.12 buitenwandopeningen; niet gevuld, buitenluchtopeningen
31.20 buitenwandopeningen; gevuld met ramen, algemeen (verzamelniveau)
31.21 buitenwandopeningen; gevuld met ramen, gesloten ramen
31.22 buitenwandopeningen; gevuld met ramen, ramen draaiend aan een kant
31.23 buitenwandopeningen; gevuld met ramen, schuiframen
31.24 buitenwandopeningen; gevuld met ramen, ramen draaiend op verticale of horizontale as
31.25 buitenwandopeningen; gevuld met ramen, combinatieramen
31.30 buitenwandopeningen; gevuld met deuren, algemeen (verzamelniveau)
31.31 buitenwandopeningen; gevuld met deuren, draaideuren
31.32 buitenwandopeningen; gevuld met deuren, schuifdeuren
31.33 buitenwandopeningen; gevuld met deuren, tuimeldeuren
31.34 buitenwandopeningen; gevuld met deuren, tourniqets
31.40 buitenwandopeningen; gevuld met puien, algemeen (verzamelniveau)
31.41 buitenwandopeningen; gevuld met puien, gesloten puien
32 binnenwandopeningen
32.10 binnenwandopeningen; niet gevuld, algemeen (verzamelniveau)
32.11 binnenwandopeningen; niet gevuld, openingen als doorgang
32.12 binnenwandopeningen; niet gevuld, openingen als doorzicht
32.20 binnenwandopeningen; gevuld met ramen, algemeen (verzamelniveau)
32.21 binnenwandopeningen; gevuld met ramen, gesloten ramen
32.22 binnenwandopeningen; gevuld met ramen, ramen draaiend aan een kant
32.23 binnenwandopeningen; gevuld met ramen, schuiframen
32.24 binnenwandopeningen; gevuld met ramen, ramen draaiend op verticale of horizontale as
32.25 binnenwandopeningen; gevuld met ramen, combinatieramen
32.30 binnenwandopeningen; gevuld met deuren, algemeen (verzamelniveau)
32.31 binnenwandopeningen; gevuld met deuren, draaideuren
32.32 binnenwandopeningen; gevuld met deuren, schuifdeuren
32.33 binnenwandopeningen; gevuld met deuren, tuimeldeuren
32.34 binnenwandopeningen; gevuld met deuren, tourniqets
32.40 binnenwandopeningen; gevuld met puien, algemeen (verzamelniveau)
32.41 binnenwandopeningen; gevuld met puien, gesloten puien
33 vloeropeningen
33.10 vloeropeningen; niet gevuld, algemeen (verzamelniveau)
33.11 vloeropeningen; niet gevuld, openingen als doorgang
33.12 vloeropeningen; niet gevuld, openingen als doorzicht
33.20 vloeropeningen; gevuld, algemeen (verzamelniveau)
33.21 vloeropeningen; gevuld, beloopbare vullingen
33.22 vloeropeningen; gevuld, niet-beloopbare vullingen
34 balustrades en leuningen
34.10 balustrades en leuningen; balustrades, algemeen (verzamelniveau)
34.11 balustrades en leuningen; balustrades, binnenbalustrades
34.12 balustrades en leuningen; balustrades, buitenbalustrades
34.20 balustrades en leuningen; leuningen, algemeen (verzamelniveau)
34.21 balustrades en leuningen; leuningen, binnenleuningen
34.22 balustrades en leuningen; leuningen, buitenleuningen
37 dakopeningen
37.10 dakopeningen; niet gevuld, algemeen (verzamelniveau)
37.11 dakopeningen; niet gevuld, daglichtopeningen
37.12 dakopeningen; niet gevuld, buitenluchtopeningen
37.20 dakopeningen; gevuld, algemeen (verzamelniveau)
37.21 dakopeningen; gevuld, gesloten ramen
37.22 dakopeningen; gevuld, ramen draaiend aan één kant
37.23 dakopeningen; gevuld, schuiframen
37.24 dakopeningen; gevuld, ramen draaiend op een as
37.25 dakopeningen; gevuld, combinatieramen
38 inbouwpakketten
38.10 inbouwpakketten; algemeen (verzamelniveau)
38.11 inbouwpakketten; inbouwpakketten met te openen delen
38.12 inbouwpakketten; inbouwpakketten met gesloten delen
4- AFWERKINGEN
41 buitenwandafwerkingen
41.10 buitenwandafwerkingen; algemeen (verzamelniveau)
41.11 buitenwandafwerkingen; afwerklagen
41.12 buitenwandafwerkingen; bekledingen
41.13 buitenwandafwerkingen; voorzetwanden
42 binnenwandafwerkingen
42.10 binnenwandafwerkingen; algemeen (verzamelniveau)
42.11 binnenwandafwerkingen; afwerklagen
42.12 binnenwandafwerkingen; bekledingen
43 vloerafwerkingen
43.10 vloerafwerkingen; verhoogd, algemeen (verzamelniveau)
43.11 vloerafwerkingen; verhoogd, podiums
43.12 vloerafwerkingen; verhoogd, installatievloeren
43.20 vloerafwerkingen; niet verhoogd, algemeen (verzamelniveau)
43.21 vloerafwerkingen; niet verhoogd, afwerklagen
43.22 vloerafwerkingen; niet verhoogd, bekledingen
43.23 vloerafwerkingen; niet verhoogd, systeemvloerafwerkingen
44 trap- en hellingafwerkingen
44.10 trap- en hellingafwerkingen; trapafwerkingen, algemeen (verzamelniveau)
44.11 trap- en hellingafwerkingen; trapafwerkingen, afwerklagen
44.12 trap- en hellingafwerkingen; trapafwerkingen, bekledingen
44.13 trap- en hellingafwerkingen; trapafwerkingen, systeemafwerkingen
44.20 trap- en hellingafwerkingen; hellingafwerkingen, algemeen (verzamelniveau)
44.21 trap- en hellingafwerkingen; hellingafwerkingen, afwerklagen
44.22 trap- en hellingafwerkingen; hellingafwerkingen, bekledingen
44.23 trap- en hellingafwerkingen; hellingafwerkingen, systeemafwerkingen
45 plafondafwerkingen
45.10 plafondafwerkingen; verlaagd, algemeen (verzamelniveau)
45.11 plafondafwerkingen; verlaagd, verlaagde plafonds
45.12 plafondafwerkingen; verlaagd, systeem plafonds
45.14 plafondafwerkingen; verlaagd, koofconstructies
45.15 plafondafwerkingen; verlaagd, gordijnplanken
45.20 plafondafwerkingen; niet verlaagd, algemeen (verzamelniveau)
45.21 plafondafwerkingen; niet verlaagd, afwerkingen
45.22 plafondafwerkingen; niet verlaagd, bekledingen
45.23 plafondafwerkingen; niet verlaagd, systeemafwerkingen
45.24 plafondafwerkingen; niet verlaagd, koofconstructies
45.25 plafondafwerkingen; niet verlaagd, gordijnplanken
47 dakafwerkingen
47.10 dakafwerkingen; afwerkingen, algemeen (verzamelniveau)
47.11 dakafwerkingen; afwerkingen, vlakke dakafwerkingen
47.12 dakafwerkingen; afwerkingen, hellende dakafwerkingen
47.13 dakafwerkingen; afwerkingen, luifel afwerkingen
47.14 dakafwerkingen; afwerkingen, overkappings afwerkingen
47.15 dakafwerkingen; afwerkingen, beloopbare dakafwerkingen
47.16 dakafwerkingen; afwerkingen, berijdbare dakafwerkingen
47.20 dakafwerkingen; bekledingen, algemeen (verzamelniveau)
47.21 dakafwerkingen; bekledingen, vlakke bekledingen
47.22 dakafwerkingen; bekledingen, hellende bekledingen
47.23 dakafwerkingen; bekledingen, luifel bekledingen
47.24 dakafwerkingen; bekledingen, overkapping bekledingen
47.25 dakafwerkingen; bekledingen, beloopbare dak bekledingen
47.26 dakafwerkingen; bekledingen, berijdbare dak bekledingen
48 afwerkingspakketten
48.10 afwerkingspakketten; algemeen (verzamelniveau)
48.11 afwerkingspakketten; naadloze afwerkingen
48.12 afwerkingspakketten; overige afwerkingen
5- INSTALLATIES WERKTUIGBOUWKUNDIG
51 warmte-opwekking
51.10 warmte-opwekking; lokaal, algemeen (verzamelniveau)
51.11 warmte-opwekking; lokaal, gasvormige brandstoffen
51.12 warmte-opwekking; lokaal, vloeibare brandstoffen
51.13 warmte-opwekking; lokaal, vaste brandstoffen
51.14 warmte-opwekking; lokaal, schoorstenen/kanalen (niet bouwkundig)
51.16 warmte-opwekking; lokaal, gecombineerde tapwaterverwarming
51.19 warmte-opwekking; lokaal, brandstoffenopslag
51.20 warmte-opwekking; centraal, algemeen (verzamelniveau)
51.21 warmte-opwekking; centraal, gasvormige brandstoffen
51.22 warmte-opwekking; centraal, vloeibare brandstoffen
51.23 warmte-opwekking; centraal, vaste brandstoffen
51.24 warmte-opwekking; centraal, schoorstenen/kanalen (niet bouwkundig)
51.26 warmte-opwekking; centraal, gecombineerde tapwater verwarming
51.29 warmte-opwekking; centraal, brandstoffenopslag
51.30 warmte-opwekking; toegeleverde warmte, algemeen (verzamelniveau)
51.31 warmte-opwekking; toegeleverde warmte, water tot 140° C.
51.32 warmte-opwekking; toegeleverde warmte, water boven 140° C.
51.33 warmte-opwekking; toegeleverde warmte, stoom
51.36 warmte-opwekking; toegeleverde warmte, gecombineerde tapwaterverwarming
51.40 warmte-opwekking; warmte-krachtkoppeling, algemeen (verzamelniveau)
51.41 warmte-opwekking; warmte-krachtkoppeling, total-energy
51.44 warmte-opwekking; warmte-krachtkoppeling, schoorstenen/kanalen (niet bouwkundig)
51.46 warmte-opwekking; warmte-krachtkoppeling, gecombineerde tapwaterverwarming
51.49 warmte-opwekking; warmte-krachtkoppeling, brandstoffenopslag
51.50 warmte-opwekking; bijzonder, algemeen (verzamelniveau)
51.51 warmte-opwekking; bijzonder, warmtepomp
51.52 warmte-opwekking; bijzonder, zonnecollectoren
51.53 warmte-opwekking; bijzonder, accumulatie
51.54 warmte-opwekking; bijzonder, aardwarmte
51.55 warmte-opwekking; bijzonder, kernenergie
52 afvoeren
52.10 afvoeren; regenwater, algemeen (verzamelniveau)
52.11 afvoeren; regenwater, afvoerinstallatie; in het gebouw
52.12 afvoeren; regenwater, afvoerinstallatie; buiten het gebouw
52.16 afvoeren; regenwater, pompsysteem
52.20 afvoeren; fecaliën, algemeen (verzamelniveau)
52.21 afvoeren; fecaliën, standaard systeem
52.22 afvoeren; fecaliën, vacuümsysteem
52.23 afvoeren; fecaliën, overdruksysteem
52.26 afvoeren; fecaliën, pompsysteem
52.30 afvoeren; afvalwater, algemeen (verzamelniveau)
52.31 afvoeren; afvalwater, huishoudelijk afval
52.32 afvoeren; afvalwater, bedrijfsafval
52.36 afvoeren; afvalwater, pompsysteem
52.40 afvoeren; gecombineerd, algemeen (verzamelniveau)
52.41 afvoeren; gecombineerd, geïntegreerd systeem
52.46 afvoeren; gecombineerd, pompsysteem
52.50 afvoeren; speciaal, algemeen (verzamelniveau)
52.51 afvoeren; speciaal, chemisch verontreinigd afvalwater
52.52 afvoeren; speciaal, biologisch besmet afvalwater
52.53 afvoeren; speciaal, radioactief besmet afvalwater
52.56 afvoeren; speciaal, pompsysteem
52.60 afvoeren; vast vuil, algemeen (verzamelniveau)
52.61 afvoeren; vast vuil, stortkokers
52.62 afvoeren; vast vuil, vacuümsysteem
52.63 afvoeren; vast vuil, persluchtsysteem
52.64 afvoeren; vast vuil, verdichtingssysteem
52.65 afvoeren; vast vuil, verbrandingssysteem
53 water
53.10 water; drinkwater, algemeen (verzamelniveau)
53.11 water; drinkwater, netaansluiting
53.12 water; drinkwater, bronaansluiting
53.13 water; drinkwater, reinwaterkelderaansluiting
53.14 water; drinkwater, drukverhoging
53.19 water; drinkwater, opslagtanks
53.20 water; verwarmd tapwater, algemeen (verzamelniveau)
53.21 water; verwarmd tapwater, direct verwarmd met voorraad
53.22 water; verwarmd tapwater, indirect verwarmd met voorraad
53.23 water; verwarmd tapwater, doorstroom; direct verwarmd
53.24 water; verwarmd tapwater, doorstroom; indirect verwarmd
53.30 water; bedrijfswater, algemeen (verzamelniveau)
53.31 water; bedrijfswater, onthard-watersysteem
53.32 water; bedrijfswater, demi-watersysteem
53.33 water; bedrijfswater, gedistilleerd-watersysteem
53.34 water; bedrijfswater, zwembad-watersysteem
53.40 water; gebruiksstoom en condens, algemeen (verzamelniveau)
53.41 water; gebruiksstoom en condens, lage-druk stoomsysteem
53.42 water; gebruiksstoom en condens, hoge-druk stoomsysteem
53.44 water; gebruiksstoom en condens, condens verzamelsysteem
53.50 water; waterbehandeling, algemeen (verzamelniveau)
53.51 water; waterbehandeling, filtratiesysteem
53.52 water; waterbehandeling, absorptiesysteem
53.53 water; waterbehandeling, ontgassingsysteem
53.54 water; waterbehandeling, destillatiesysteem
54 gassen
54.10 gassen; brandstof, algemeen (verzamelniveau)
54.11 gassen; brandstof, aardgasvoorziening
54.12 gassen; brandstof, butaanvoorziening
54.13 gassen; brandstof, propaanvoorziening
54.14 gassen; brandstof, LPG-voorziening
54.20 gassen; perslucht en vacuüm, algemeen (verzamelniveau)
54.21 gassen; perslucht en vacuüm, persluchtvoorziening
54.22 gassen; perslucht en vacuüm, vacuümvoorziening
54.30 gassen; medisch, algemeen (verzamelniveau)
54.31 gassen; medisch, zuurstofvoorziening
54.32 gassen; medisch, carbogeenvoorziening
54.33 gassen; medisch, lachgasvoorziening
54.34 gassen; medisch, koolzuurvoorziening
54.35 gassen; medisch, medische luchtvoorziening
54.40 gassen; technisch, algemeen (verzamelniveau)
54.41 gassen; technisch, stikstofvoorziening
54.42 gassen; technisch, waterstofvoorziening
54.43 gassen; technisch, argonvoorziening
54.44 gassen; technisch, heliumvoorziening
54.45 gassen; technisch, acetyleenvoorziening
54.46 gassen; technisch, propaanvoorziening
54.47 gassen; technisch, koolzuurvoorziening
54.50 gassen; bijzonder, algemeen (verzamelniveau)
54.51 gassen; bijzonder, voorziening; zuivere gassen
54.52 gassen; bijzonder, voorziening; menggassen
55 koude-opwekking en distributie
55.10 koude-opwekking; lokaal, algemeen (verzamelniveau)
55.11 koude-opwekking; lokaal, raamkoelers
55.12 koude-opwekking; lokaal, splitsystemen
55.13 koude-opwekking; lokaal, compactsystemen
55.20 koude-opwekking; centraal, algemeen (verzamelniveau)
55.21 koude-opwekking; centraal, compressorensystemen
55.22 koude-opwekking; centraal, absorptiesystemen
55.23 koude-opwekking; centraal, grondwatersystemen
55.24 koude-opwekking; centraal, oppervlaktewatersystemen
55.30 koude-opwekking; distributie, algemeen (verzamelniveau)
55.31 koude-opwekking; distributie, distributiesystemen
56 warmtedistributie
56.10 warmtedistributie; water, algemeen (verzamelniveau)
56.11 warmtedistributie; water, radiatorsystemen
56.12 warmtedistributie; water, convectorsystemen
56.13 warmtedistributie; water, vloerverwarmingssystemen
56.20 warmtedistributie; stoom, algemeen (verzamelniveau)
56.21 warmtedistributie; stoom, radiatorsystemen
56.22 warmtedistributie; stoom, convectorsystemen
56.24 warmtedistributie; stoom, stralingspanelen
56.30 warmtedistributie; lucht, algemeen (verzamelniveau)
56.31 warmtedistributie; lucht, directe distributiesysteem
56.32 warmtedistributie; lucht, systeem met stralingsoverdracht
56.40 warmtedistributie; bijzonder, algemeen (verzamelniveau)
56.41 warmtedistributie; bijzonder, zonnewarmtesystemen
56.42 warmtedistributie; bijzonder, aardwarmtesystemen
56.43 warmtedistributie; bijzonder, centraal warmtepompsysteem
57 luchtbehandeling
57.10 luchtbehandeling; natuurlijke ventilatie, algemeen (verzamelniveau)
57.11 luchtbehandeling; natuurlijke ventilatie, voorzieningen; regelbaar
57.12 luchtbehandeling; natuurlijke ventilatie, voorzieningen; niet regelbaar
57.20 luchtbehandeling; lokale mechanische afzuiging, algemeen (verzamelniveau)
57.21 luchtbehandeling; lokale mechanische afzuiging, afzuiginstallatie
57.30 luchtbehandeling; centrale mechanische afzuiging, algemeen (verzamelniveau)
57.31 luchtbehandeling; centrale mechanische afzuiging, afzuiginstallatie
57.40 luchtbehandeling; lokale mechanische ventilatie, algemeen (verzamelniveau)
57.41 luchtbehandeling; lokale mechanische ventilatie, ventilatie-installatie
57.50 luchtbehandeling; centrale mechanische ventilatie, algemeen (verzamelniveau)
57.51 luchtbehandeling; centrale mechanische ventilatie, ventilatie-installatie
57.52 luchtbehandeling; centrale mechanische ventilatie, ventilatie-installatie met warmteterugwinning
57.60 luchtbehandeling; lokaal, algemeen (verzamelniveau)
57.61 luchtbehandeling; lokaal, luchtbehandelingsinstallatie
57.70 luchtbehandeling; centraal, algemeen (verzamelniveau)
57.71 luchtbehandeling; centraal, luchtbehandelingsinstallatie
58 regeling klimaat en sanitair
58.10 regeling klimaat en sanitair; specifieke regelingen, algemeen (verzamelniveau)
58.11 regeling klimaat en sanitair; specifieke regelingen, specifieke regeling
58.12 regeling klimaat en sanitair; specifieke regelingen, gecombineerde regeling
58.20 regeling klimaat en sanitair; centrale melding, meting en sturing, algemeen (verzamelniveau)
58.21 regeling klimaat en sanitair; centrale melding, meting en sturing, specifieke regeling
58.22 regeling klimaat en sanitair; centrale melding, meting en sturing, gecombineerde regeling
6- INSTALLATIES ELEKTROTECHNISCH
61 centrale electrotechnische voorzieningen
61.10 centrale elektrotechnische voorzieningen; energie, noodstroom, algemeen (verzamelniveau)
61.11 centrale elektrotechnische voorzieningen; energie, noodstroom, eigen energieopwekking
61.20 centrale elektrotechnische voorzieningen; aarding, algemeen (verzamelniveau)
61.21 centrale elektrotechnische voorzieningen; aarding, veiligheidsaarding
61.22 centrale elektrotechnische voorzieningen; aarding, medische aarding
61.23 centrale elektrotechnische voorzieningen; aarding, speciale aarding
61.24 centrale elektrotechnische voorzieningen; aarding, statische elektriciteit
61.25 centrale elektrotechnische voorzieningen; aarding, bliksemafleiding
61.26 centrale elektrotechnische voorzieningen; aarding, potentiaalvereffening
61.30 centrale elektrotechnische voorzieningen; kanalisatie, algemeen (verzamelniveau)
61.31 centrale elektrotechnische voorzieningen; kanalisatie, t.b.v. installaties voor hoge spanning
61.32 centrale elektrotechnische voorzieningen; kanalisatie, t.b.v. installaties voor lage spanning 61.33 centrale elektrotechnische voorzieningen; kanalisatie, t.b.v. installaties voor communicatie
of beveiliging
61.40 centrale elektrotechnische voorzieningen; energie, hoogspanning, algemeen
61.41 centrale elektrotechnische voorzieningen; energie, hoogspanning, 1 Kv en hoger
61.50 centrale elektrotechnische voorzieningen; energie, laagspanning, algemeen 61.51 centrale elektrotechnische voorzieningen; energie, laagspanning, lager dan 1 Kv en hoger
dan 100 V
61.60 centrale elektrotechnische voorzieningen; energie, zeer lage spanning, algemeen
61.61 centrale elektrotechnische voorzieningen; energie, zeer lage spanning, lager dan 100 V
61.70 centrale elektrotechnische voorzieningen; bliksemafleiding, algemeen
61.71 centrale elektrotechnische voorzieningen; bliksemafleiding
62 krachtstroom
62.10 krachtstroom; hoogspanning, algemeen (verzamelniveau)
62.11 krachtstroom; hoogspanning, 1 t/m 3 Kv
62.12 krachtstroom; hoogspanning, boven 3 Kv
62.20 krachtstroom; laagspanning, onbewaakt, algemeen (verzamelniveau)
62.21 krachtstroom; laagspanning, onbewaakt, 220/230 V - 380 V
62.22 krachtstroom; laagspanning, onbewaakt, 380 V - 660 V
62.23 krachtstroom; laagspanning, onbewaakt, 660 V - 1 Kv
62.30 krachtstroom; laagspanning, bewaakt, algemeen (verzamelniveau)
62.31 krachtstroom; laagspanning, bewaakt, 220/230 V - 380 V
62.32 krachtstroom; laagspanning, bewaakt, 380 V - 660 V
62.33 krachtstroom; laagspanning, bewaakt, 660 V - 1 kV
62.40 krachtstroom; laagspanning, gestabiliseerd, algemeen (verzamelniveau)
62.41 krachtstroom; laagspanning, gestabiliseerd, 220/230 V - 380 V
62.42 krachtstroom; laagspanning, gestabiliseerd, 380 V - 660 V
62.43 krachtstroom; laagspanning, gestabiliseerd, 660 V - 1 Kv
62.50 krachtstroom; laagspanning, gecompenseerd, algemeen (verzamelniveau)
62.51 krachtstroom; laagspanning, gecompenseerd, 220/230 V - 380 V
62.52 krachtstroom; laagspanning, gecompenseerd, 380 V - 660 V
62.53 krachtstroom; laagspanning, gecompenseerd, 660 V - 1 Kv
63 verlichting
63.10 verlichting; standaard, onbewaakt, algemeen (verzamelniveau)
63.11 verlichting; standaard, onbewaakt, 220/230 V
63.12 verlichting; standaard, onbewaakt, 115 V
63.13 verlichting; standaard, onbewaakt, 42 V
63.14 verlichting; standaard, onbewaakt, 24 V
63.20 verlichting; calamiteiten, decentraal gevoed, algemeen (verzamelniveau)
63.23 verlichting; calamiteiten, decentraal gevoed, 42 V
63.24 verlichting; calamiteiten, decentraal gevoed, 24 V
63.30 verlichting; bijzonder, onbewaakt, algemeen (verzamelniveau)
63.31 verlichting; bijzonder, onbewaakt, 220/230 V
63.32 verlichting; bijzonder, onbewaakt, 115 V
63.33 verlichting; bijzonder, onbewaakt, 42 V
63.34 verlichting; bijzonder, onbewaakt, 24 V
63.40 verlichting; standaard, bewaakt, algemeen (verzamelniveau)
63.41 verlichting; standaard, bewaakt, 220/230 V
63.42 verlichting; standaard, bewaakt, 115 V
63.43 verlichting; standaard, bewaakt, 42 V
63.44 verlichting; standaard, bewaakt, 24 V
63.50 verlichting; calamiteiten, centraal gevoed, algemeen (verzamelniveau)
63.51 verlichting; calamiteiten, centraal gevoed, 220/230 V
63.52 verlichting; calamiteiten, centraal gevoed, 115 V
63.53 verlichting; calamiteiten, centraal gevoed, 42 V
63.54 verlichting; calamiteiten, centraal gevoed, 24 V
63.60 verlichting; bijzonder, bewaakt, algemeen (verzamelniveau)
63.61 verlichting; bijzonder, bewaakt, 220/230 V
63.62 verlichting; bijzonder, bewaakt, 115 V
63.63 verlichting; bijzonder, bewaakt, 42 V
63.64 verlichting; bijzonder, bewaakt, 24 V
63.70 verlichting; reclame, algemeen (verzamelniveau)
63.71 verlichting; reclame, 220/230 V
63.72 verlichting; reclame, 115 V
63.73 verlichting; reclame, 42 V
63.74 verlichting; reclame, 24 V
63.75 verlichting; reclame, 1 Kv en hoger
64 communicatie
64.10 communicatie; overdracht van signalen, algemeen (verzamelniveau)
64.11 communicatie; overdracht van signalen, algemene signaleringen
64.12 communicatie; overdracht van signalen, algemene personenoproep
64.13 communicatie; overdracht van signalen, tijdsignalering
64.14 communicatie; overdracht van signalen, aanwezigheid-/beletsignalering
64.20 communicatie; overdracht van geluid/spraak, algemeen (verzamelniveau)
64.21 communicatie; overdracht van geluid/spraak, telefoon
64.22 communicatie; overdracht van geluid/spraak, intercom
64.23 communicatie; overdracht van geluid/spraak, radio/mobilofoon
64.24 communicatie; overdracht van geluid/spraak, geluidsdistributie
64.25 communicatie; overdracht van geluid/spraak, vertaalsystemen
64.26 communicatie; overdracht van geluid/spraak, conferentiesystemen
64.30 communicatie; overdracht van beelden, algemeen (verzamelniveau)
64.31 communicatie; overdracht van beelden, gesloten televisiecircuits
64.32 communicatie; overdracht van beelden, beeldreproductie
64.33 communicatie; overdracht van beelden, film/dia/overhead
64.40 communicatie; overdracht van data, algemeen (verzamelniveau)
64.41 communicatie; overdracht van data, gesloten datanet
64.42 communicatie; overdracht van data, openbaar datanet
64.50 communicatie; geïntegreerde systemen, algemeen (verzamelniveau)
64.51 communicatie; geïntegreerde systemen, gesloten netwerken
64.52 communicatie; geïntegreerde systemen, openbare netwerken
64.60 communicatie; antenne-inrichtingen, algemeen
65 beveiliging
65.10 beveiliging; brand, algemeen (verzamelniveau)
65.11 beveiliging; brand, detectie en alarmering
65.12 beveiliging; brand, deurvergrendelingen en -ontgrendelingen
65.13 beveiliging; brand, brandbestrijding
65.20 beveiliging; braak, algemeen (verzamelniveau)
65.21 beveiliging; braak, detectie en alarmering
65.22 beveiliging; braak, toegangscontrole
65.30 beveiliging; overlast, detectie en alarmering, algemeen (verzamelniveau)
65.31 beveiliging; overlast, detectie en alarmering, zonweringsinstallatie
65.32 beveiliging; overlast, detectie en alarmering, elektromagnetische voorzieningen
65.33 beveiliging; overlast, detectie en alarmering, elektromagnetische voorzieningen
65.34 beveiliging; overlast, detectie en alarmering, overspanningsbeveiliging
65.35 beveiliging; overlast, detectie en alarmering, gassenbeveiliging
65.36 beveiliging; overlast, detectie en alarmering, vloeistofbeveiliging
65.37 beveiliging; overlast, detectie en alarmering, stralingsbeveiliging
65.39 beveiliging; overlast, detectie en alarmering, overige beveiligingen
65.40 beveiliging; sociale alarmering, algemeen (verzamelniveau)
65.41 beveiliging; sociale alarmering, nooddetectie; gesloten systemen
65.42 beveiliging; sociale alarmering, nooddetectie; open systemen
65.50 beveiliging; milieu-overlast, detectie en alarmering, algemeen (verzamelniveau)
66 transport
66.10 transport; liften en heftableau's, algemeen (verzamelniveau)
66.11 transport; liften en heftableau's, elektrische liften
66.12 transport; liften en heftableau's, hydraulische liften
66.13 transport; liften en heftableau's, trapliften
66.14 transport; liften en heftableau's, heftableau's
66.20 transport; roltrappen en rolpaden, algemeen (verzamelniveau)
66.21 transport; roltrappen en rolpaden, roltrappen
66.22 transport; roltrappen en rolpaden, rolpaden
66.30 transport; goederen, algemeen (verzamelniveau)
66.31 transport; goederen, goederenliften
66.32 transport; goederen, goederenheffers
66.33 transport; goederen, baantransportmiddelen
66.34 transport; goederen, bandtransportmiddelen
66.35 transport; goederen, baktransportmiddelen
66.36 transport; goederen, hijswerktuigen
66.37 transport; goederen, vrije-baan-transportvoertuigen
66.40 transport; documenten, algemeen (verzamelniveau)
66.41 transport; documenten, buizenpost
66.42 transport; documenten, railcontainer banen
66.44 transport; documenten, bandtransportmiddelen
67 gebouwbeheervoorzieningen
67.10 gebouwbeheervoorzieningen; bediening en signalering, algemeen (verzamelniveau)
67.11 gebouwbeheervoorzieningen; bediening en signalering, elektrotechnische systemen
67.12 gebouwbeheervoorzieningen; bediening en signalering, optische systemen
67.13 gebouwbeheervoorzieningen; bediening en signalering, pneumatische systemen
67.14 gebouwbeheervoorzieningen; bediening en signalering, geïntegreerde systemen
67.20 gebouwbeheervoorzieningen; gebouwautomatisering, algemeen (verzamelniveau)
67.21 gebouwbeheervoorzieningen; gebouwautomatisering, elektrotechnische systemen
67.22 gebouwbeheervoorzieningen; gebouwautomatisering, optische systemen
67.23 gebouwbeheervoorzieningen; gebouwautomatisering, pneumatische systemen
67.24 gebouwbeheervoorzieningen; gebouwautomatisering, geïntegreerde systemen 67.30 gebouwbeheervoorzieningen; regelinstallaties klimaat en sanitair (op afstand),
algemeen (verzamelniveau) 67.31 gebouwbeheervoorzieningen; regelinstallaties klimaat en sanitair (op afstand),
elektrotechnische systemen 67.32 gebouwbeheervoorzieningen; regelinstallaties klimaat en sanitair (op afstand),
optische systemen 67.33 gebouwbeheervoorzieningen; regelinstallaties klimaat en sanitair (op afstand),
pneumatische systemen 67.34 gebouwbeheervoorzieningen; regelinstallaties klimaat en sanitair (op afstand),
geïntegreerde systemen
7- VASTE VOORZIENINGEN
71 vaste verkeersvoorzieningen
71.10 vaste verkeersvoorzieningen; standaard, algemeen (verzamelniveau)
71.11 vaste verkeersvoorzieningen; standaard, meubileringen
71.12 vaste verkeersvoorzieningen; standaard, bewegwijzeringen
71.13 vaste verkeersvoorzieningen; standaard, kunstwerken
71.14 vaste verkeersvoorzieningen; standaard, decoraties e.d.
71.20 vaste verkeersvoorzieningen; bijzonder, algemeen (verzamelniveau)
71.21 vaste verkeersvoorzieningen; bijzonder, meubileringen
71.22 vaste verkeersvoorzieningen; bijzonder, bewegwijzeringen
71.23 vaste verkeersvoorzieningen; bijzonder, specifieke voorz. (o.a. loopleuningen)
72 vaste gebruikersvoorzieningen
72.10 vaste gebruikersvoorzieningen; standaard, algemeen (verzamelniveau)
72.11 vaste gebruikersvoorzieningen; standaard, meubilering
72.12 vaste gebruikersvoorzieningen; standaard, lichtweringen
72.13 vaste gebruikersvoorzieningen; standaard, gordijnvoorzieningen
72.14 vaste gebruikersvoorzieningen; standaard, beschermende voorzieningen
72.20 vaste gebruikersvoorzieningen; bijzonder, algemeen (verzamelniveau)
72.21 vaste gebruikersvoorzieningen; bijzonder, meubilering voor specifieke functiedoeleinden
72.22 vaste gebruikersvoorzieningen; bijzonder, instrumenten/apparatuur
73 vaste keukenvoorzieningen
73.10 vaste keukenvoorzieningen; standaard, algemeen (verzamelniveau)
73.11 vaste keukenvoorzieningen; standaard, keukenmeubilering
73.12 vaste keukenvoorzieningen; standaard, keukenapparatuur
73.20 vaste keukenvoorzieningen; bijzonder, algemeen (verzamelniveau)
73.21 vaste keukenvoorzieningen; bijzonder, keukenmeubilering
73.22 vaste keukenvoorzieningen; bijzonder, keukenapparatuur
74 vaste sanitaire voorzieningen
74.10 vaste sanitaire voorzieningen; standaard, algemeen (verzamelniveau)
74.11 vaste sanitaire voorzieningen; standaard, sanitaire toestellen; normaal
74.12 vaste sanitaire voorzieningen; standaard, sanitaire toestellen; aangepast
74.13 vaste sanitaire voorzieningen; standaard, accessoires
74.20 vaste sanitaire voorzieningen; bijzonder, algemeen (verzamelniveau)
74.21 vaste sanitaire voorzieningen; bijzonder, sanitaire toestellen voor bijzondere toepassing
74.22 vaste sanitaire voorzieningen; bijzonder, ingebouwde sanitaire voorzieningen
75 vaste onderhoudsvoorzieningen
75.10 vaste onderhoudsvoorzieningen; standaard, algemeen (verzamelniveau)
75.11 vaste onderhoudsvoorzieningen; standaard, gebouwonderhoudsvoorzieningen
75.12 vaste onderhoudsvoorzieningen; standaard, interieur onderhoudsvoorzieningen
75.13 vaste onderhoudsvoorzieningen; standaard, gevelonderhoudsvoorzieningen
75.20 vaste onderhoudsvoorzieningen; bijzonder, algemeen (verzamelniveau)
75.21 vaste onderhoudsvoorzieningen; bijzonder, gebouwonderhoudsvoorzieningen
75.22 vaste onderhoudsvoorzieningen; bijzonder, interieur onderhoudsvoorzieningen
75.23 vaste onderhoudsvoorzieningen; bijzonder, gemechaniseerde gevelonderhoudsvoorzieningen
76 vaste opslagvoorzieningen
76.10 vaste opslagvoorzieningen; standaard, algemeen (verzamelniveau)
76.11 vaste opslagvoorzieningen; standaard, meubileringen
76.20 vaste opslagvoorzieningen; bijzonder, algemeen (verzamelniveau)
76.21 vaste opslagvoorzieningen; bijzonder, gemechaniseerde voorzieningen
76.22 vaste opslagvoorzieningen; bijzonder, specifieke voorzieningen
8- LOSSE INVENTARIS
81 losse verkeersinventaris
81.10 losse verkeersinventaris; standaard, algemeen (verzamelniveau)
81.11 losse verkeersinventaris; standaard, meubilering
81.12 losse verkeersinventaris; standaard, bewegwijzering
81.13 losse verkeersinventaris; standaard, kunstwerken
81.14 losse verkeersinventaris; standaard, decoraties e.d.
81.20 losse verkeersinventaris; bijzonder, algemeen (verzamelniveau)
81.21 losse verkeersinventaris; bijzonder, meubilering
81.22 losse verkeersinventaris; bijzonder, bewegwijzering
81.23 losse verkeersinventaris; bijzonder, specifieke voorzieningen (o.a. afvalbakken)
82 losse gebruikersinventaris
82.10 losse gebruikersinventaris; standaard, algemeen (verzamelniveau)
82.11 losse gebruikersinventaris; standaard, meubilering
82.12 losse gebruikersinventaris; standaard, lichtweringen/verduisteringen
82.13 losse gebruikersinventaris; standaard, stofferingen
82.20 losse gebruikersinventaris; bijzonder, algemeen (verzamelniveau)
82.21 losse gebruikersinventaris; bijzonder, meubilering voor specifieke functiedoeleinden
82.22 losse gebruikersinventaris; bijzonder, instrumenten/apparatuur
83 losse keukeninventaris
83.10 losse keukeninventaris; standaard, algemeen (verzamelniveau)
83.11 losse keukeninventaris; standaard, keukenmeubilering
83.12 losse keukeninventaris; standaard, keukenapparatuur
83.13 losse keukeninventaris; standaard, kleine keukeninventaris
83.20 losse keukeninventaris; bijzonder, algemeen (verzamelniveau)
83.21 losse keukeninventaris; bijzonder, keukeninrichting
83.22 losse keukeninventaris; bijzonder, keukenapparatuur
83.23 losse keukeninventaris; bijzonder, kleine keukeninventaris
83.24 losse keukeninventaris; bijzonder, transportmiddelen
84 losse sanitaire inventaris
84.10 losse sanitaire inventaris; standaard, algemeen (verzamelniveau)
84.11 losse sanitaire inventaris; standaard, afvalvoorzieningen
84.12 losse sanitaire inventaris; standaard, voorzieningen t.b.v. hygiëne
84.13 losse sanitaire inventaris; standaard, accessoires
84.20 losse sanitaire inventaris; bijzonder, algemeen (verzamelniveau)
84.21 losse sanitaire inventaris; bijzonder, sanitaire toestellen voor bijzondere toepassing
85 losse schoonmaakinventaris
85.10 losse schoonmaakinventaris; standaard, algemeen (verzamelniveau)
85.11 losse schoonmaakinventaris; standaard, schoonmaakapparatuur
85.12 losse schoonmaakinventaris; standaard, vuilopslag
85.13 losse schoonmaakinventaris; standaard, vuiltransport
85.20 losse schoonmaakinventaris; bijzonder, algemeen (verzamelniveau)
85.21 losse schoonmaakinventaris; bijzonder, schoonmaakapparatuur
85.22 losse schoonmaakinventaris; bijzonder, vuilopslag
85.23 losse schoonmaakinventaris; bijzonder, vuiltransport
86 losse opslaginventaris
86.10 losse opslaginventaris; standaard, algemeen (verzamelniveau)
86.11 losse opslaginventaris; standaard, meubileringen
86.20 losse opslaginventaris; bijzonder, algemeen (verzamelniveau)
86.21 losse opslaginventaris; bijzonder, gemechaniseerde voorzieningen
86.22 losse opslaginventaris; bijzonder, specifieke voorzieningen
9- TERREIN
90 terrein
90.10 terrein; grondvoorzieningen, algemeen (verzamelniveau)
90.11 terrein; grondvoorzieningen, verwijderen obstakels
90.12 terrein; grondvoorzieningen, grondwaterverlagingen
90.13 terrein; grondvoorzieningen, drainagevoorzieningen
90.20 terrein; opstallen, algemeen (verzamelniveau)
90.21 terrein; opstallen, gebouwtjes met speciale functie
90.22 terrein; opstallen, overkappingen
90.30 terrein; omheiningen, algemeen (verzamelniveau)
90.31 terrein; omheiningen, muren
90.32 terrein; omheiningen, hekwerken
90.33 terrein; omheiningen, overige afscheidingen
90.34 terrein; omheiningen, toegangen
90.40 terrein; terreinafwerkingen, algemeen (verzamelniveau)
90.41 terrein; terreinafwerkingen, verhardingen
90.42 terrein; terreinafwerkingen, beplantingen
90.43 terrein; terreinafwerkingen, waterpartijen
90.44 terrein; terreinafwerkingen, keerwanden en balustrades
90.45 terrein; terreinafwerkingen, pergola's
90.50 terrein; terreinvoorzieningen, werktuigbouwkundig, algemeen (verzamelniveau)
90.51 terrein; terreinvoorzieningen, werktuigbouwkundig, verwarmingsvoorzieningen
90.52 terrein; terreinvoorzieningen, werktuigbouwkundig, afvoervoorzieningen
90.53 terrein; terreinvoorzieningen, werktuigbouwkundig, watervoorzieningen
90.54 terrein; terreinvoorzieningen, werktuigbouwkundig, gasvoorzieningen
90.55 terrein; terreinvoorzieningen, werktuigbouwkundig, koudeopwekkingsvoorzieningen
90.56 terrein; terreinvoorzieningen, werktuigbouwkundig, warmtedistributievoorzieningen
90.57 terrein; terreinvoorzieningen, werktuigbouwkundig, luchtbehandelingsvoorzieningen
90.58 terrein; terreinvoorzieningen, werktuigbouwkundig, regelingvoorzieningen
90.60 terrein; terreinvoorzieningen, elektrotechnisch, algemeen (verzamelniveau)
90.61 terrein; terreinvoorzieningen, elektrotechnisch, elektrotechnische en aardingsvoorzieningen
90.62 terrein; terreinvoorzieningen, elektrotechnisch, krachtvoorzieningen
90.63 terrein; terreinvoorzieningen, elektrotechnisch, lichtvoorzieningen
90.64 terrein; terreinvoorzieningen, elektrotechnisch, communicatievoorzieningen
90.65 terrein; terreinvoorzieningen, elektrotechnisch, beveiligingsvoorzieningen
90.66 terrein; terreinvoorzieningen, elektrotechnisch, transportvoorzieningen
90.67 terrein; terreinvoorzieningen, elektrotechnisch, beheervoorzieningen
90.70 terrein; terreininrichtingen, standaard, algemeen (verzamelniveau)
90.71 terrein; terreininrichtingen, standaard, terreinmeubilering
90.72 terrein; terreininrichtingen, standaard, bewegwijzering
90.73 terrein; terreininrichtingen, standaard, kunstwerken
90.74 terrein; terreininrichtingen, standaard, decoraties e.d.
90.80 terrein; terreininrichtingen, bijzonder, algemeen (verzamelniveau)
90.81 terrein; terreininrichtingen, bijzonder, terreinmeubilering
90.82 terrein; terreininrichtingen, bijzonder, specifieke voorzieningen
90.83 terrein; terreininrichtingen, bijzonder, bijzondere verhardingen
0- INDIRECTE PROJECTVOORZIENINGEN 0-.10 indirecte projectvoorzieningen; werkterreininrichting, algemeen (verzamelniveau)
0-.11 indirecte projectvoorzieningen; werkterreininrichting, bijkomende werken
0-.12 indirecte projectvoorzieningen; werkterreininrichting, personen/materiaalvoorzieningen
0-.13 indirecte projectvoorzieningen; werkterreininrichting, energievoorzieningen
0-.14 indirecte projectvoorzieningen; werkterreininrichting, beveiligingsvoorzieningen
0-.15 indirecte projectvoorzieningen; werkterreininrichting, doorwerkvoorzieningen
0-.16 indirecte projectvoorzieningen; werkterreininrichting, voorzieningen belendende percelen
0-.17 indirecte projectvoorzieningen; werkterreininrichting, onderhoudsvoorzieningen
0-.20 indirecte projectvoorzieningen; materieelvoorzieningen, algemeen (verzamelniveau)
0-.21 indirecte projectvoorzieningen; materieelvoorzieningen, transport
0-.22 indirecte projectvoorzieningen; materieelvoorzieningen, gereedschappen
0-.30 indirecte projectvoorzieningen; risicodekking, algemeen (verzamelniveau)
0-.31 indirecte projectvoorzieningen; risicodekking, verzekeringen
0-.32 indirecte projectvoorzieningen; risicodekking, waarborgen
0-.33 indirecte projectvoorzieningen; risicodekking, prijsstijgingen
0-.40 indirecte projectvoorzieningen; projectorganisatie, algemeen (verzamelniveau)
0-.41 indirecte projectvoorzieningen; projectorganisatie, administratie
0-.42 indirecte projectvoorzieningen; projectorganisatie, uitvoering
0-.43 indirecte projectvoorzieningen; projectorganisatie, documentatie
0-.50 indirecte projectvoorzieningen; bedrijfsorganisatie, algemeen (verzamelniveau)
0-.51 indirecte projectvoorzieningen; bedrijfsorganisatie, bestuur en directie
0-.52 indirecte projectvoorzieningen; bedrijfsorganisatie, winstregelingen
EATC - Eindhoven
3
Differ - Eindhoven
3
a. IFC 2x3 TC1- buildingSMARTOm BIM (modellen en informatie) te kunnen delen is het noodzakelijk om een universeelbestandsformaat te kiezen. Het bestandsformaat welke door iedere BIM software in en uit kanworden gelezen is IFC (Industry Foundation Classes 2x3 TC1). IFC geeft de mogelijkheid om, netals bijvoorbeeld PDF, informatie te delen zonder dat derden de inhoud kunnen bewerken.
Omdat er naast de geometrische informatie afstemming ook technische informatie wordt gecom-municeerd, is dit wenselijk om het via de modellen te delen. Hierdoor zal het BIM daadwerkelijkals primair informatiebron gaan dienen. Om dit te kunnen doen is het belangrijk om duidelijkeafspraken en spelregels te bepalen over waar welke informatie moet komen te staan en wanneerdit in het proces moet worden gedaan.
Building SMART, de internationale organisatie achter IFC, heeft een uiteenzetting gemaakt vanobjecten en de daarbij behorende parameters. In een parameter ondervang je het soort informatiedie passend is bij het object.
Deze parameters verschillen per entiteit. BuildingSMART heeft daarin een onderverdeling gemaakt, maarheeft hieraan geen eenheden bepaalt aangezien dezevaak land of regio specifiek zijn. Building SMART heefthiervoor een site gemaakt waarop deze gehele structuurterug te vinden is (http://www.buildingsmart-tech.org/if-c/IFC2x3/TC1/html/). Wij geven een toelichting op dezestructuur om tot een werkbaar model te kunnen komen.
Termen:Entiteit: Dit is een digitale voorstelling van een elementwat voorkomt in de gebouwde omgeving. Deze entitei-ten zijn gedefinieerd en hebben specifieke eigenschappen (base quantities en property sets). Eenvoorbeeld hiervan is dat een wand een wand representeert en een deur een deur representeert.Beiden hebben verschillende maatgevende maten en eigenschappen. Er zijn entiteiten voorzowel bouwkunde, constructie als installatie techniek.
Quantity: Binnen de definities van IFC staat dat hoeveelheden die uit de vorm van een entiteit afge-leid kunnen worden niet vastgelegd zijn als gegevens van element. Deze hoeveelheden dienenuit een element berekend worden door software. Het aantal, en de verschillende soorten hoeveel-heden kan per software verschillen, in de omschrijving bij de entiteiten is gekozen om de hoeveel-heden van Solibri aan te houden.
Base Quantity: Naast de analyseerbare hoeveelheden (Quantities) zijn er ook hoeveelheden perentiteit welke standaard zijn of niet analyseerbaar zijn. Dit zijn de Base Quantities. Bij kolommenis dit bijvoorbeeld de handelslengte (nominallength). In het model is alleen de netto versie van dekolom terug te vinden. Als de geanalyseerde hoeveelheid niet overeenkomt met de vastgesteldehoeveelheid is de vastgestelde hoeveelheid leidend. Deze hoeveelheden worden door de model-leersoftware weggeschreven naar de Base Quantities.
Opgesteld door: Ir. J.B.F. (Jeffrey) Truijens Ing. H.J. (Jasper) de Mink
Bekijken van een IFC
Een voorbeeld van hoe de Quantities, Base Quantities en Property Sets eruit zien binnen een vande viewers (Solibri Model Viewer) is hieronder weergegeven:
Porperty set (Pset): Eigenschappen van een entiteit die niet berekend kunnen worden aan de handvan de vorm van de entiteit vallen onder properties. Per entiteit zijn er een standaard set proper-ties gedefinieerd.
b. Entiteiten
Overzicht entiteiten
Zoals eerder gedefinieerd is een entiteit is een digitale voorstelling van een element wat voorkomtin de gebouwde omgeving. Deze entiteiten zijn gedefinieerd en hebben specifieke eigenschappen(base quantities en property sets). Een voorbeeld van een entiteit is dat een wand een wandrepresenteert en een deur een deur representeert. Beiden hebben verschillende maatgevendematen en eigenschappen.
Er zijn 93 verschillende entiteiten binnen IFC gedefinieerd. Deze entiteiten zijn er zowel voorbouwkunde, constructie als installatie techniek. Binnen IFC zijn deze entiteiten niet gekoppeldaan een discipline en kunnen ze binnen elke discipline gebruikt worden.
Voor het gebruik van verdere analyses lichten wij de entiteiten toe waarvan de gekoppelde infor-matie het meest wordt gebruikt binnen onze processen, 20 stuks. Aan de hand van deze overzich-ten kunnen we het te verwachten informatieaanbod uit de modellen managen en eenduidig inter-preteren.
= wordt in dit document nader toegelicht
c. Quantities, Base Quantities & PsetsQuantitiesDit zijn hoeveelheden die berekend kunnen worden aan de hand van de vorm van de entiteit.Omdat bij verschillende entiteiten verschillende maten maatgevend zijn verschillen de base quan-tities ook per entiteit. Een oppervlakte van een vloer is een ander dan die van een wand.
Hoeveelheden zijn gebaseerd op de volgende hoofdanalyses:• Lengte: Dit is o.a. de basis voor length, Profile width, Profile Heigth, Bounding Box Height, Diameter, Thickness en Frame Length• Oppervlakte: Dit is o.a. de basis voor Bottom Area, Skin Area, Gross Area en Area of Openings.• Inhoud: Dit is de basis voor Volume.
Aanvullend zijn er aantal (IfcQuantityCount), gewicht (IfcQuantity-Weight) en tijd (IfcQuantityTime).
Bounding Box: Bij veel entiteiten worden de afmetingen van de boun-dingbox aangegeven. De boundingbox is de buitenwerkse maat vanhet totale element. Deze maat komt vaak overeen met de Length ofHeight van een element als dit lijkt op een basis ruimtelijke vorm(kubus, balk, cilinder) met een horizontaal of verticaal grondvlak,met een lengte die hier haaks op staat. Voor vormen die hiervanafwijken kan de boundingbox niet als leidende maat gebruiktworden.
Voorbeeld: Als een geroteerde balk de entiteit ‘object’ meekrijgt in plaats van de juiste entiteit‘beam’, is slechts het uitlezen van de hoeveelheden van de Bounding Box mogelijk. Het uitlezenvan de actual length is dus niet mogelijk.
Base QuantityHet overzicht van de base quanties is opgesteld aan de hand van de Building Smart site:http://www.buildingsmart-tech.org/ifc/IFC2x3/TC1/html/index.htm . Hier kan je meer informatievinden over de achtergrond van de Base Quantities.
Property Set (Pset)Eigenschappen van een entiteit die niet berekend kunnen worden aan de hand van de vorm vande entiteit vallen onder properties. Deze moeten dus handmatig worden toegekend. Voorbeel-den zijn: IsExternal, LoadBearing, FireRating, AcousticRating en ThermalTransmittance. Perentiteit zijn er een standaard groep properties gedefinieerd, een property set, afgekort Pset.
Sommige properties kunnen verschillend geïnterpreteerd worden, IFC schrijft hier geen eenheidin voor. Dit dient per project of entiteit worden afgesproken, gebaseerd op de informatie behoef-te.
Voorbeeld: FireRating, dit kan WBDBO of moment tot bezwijken zijn.
Actual Length
IfcBeamQuantities
Base Quantities
Name Description Value TypeLenght A length measure is the value of a distance Solibri analysisProfile Width The Profile Width measure is the value of a distance Solibri analysisProfile Height The Profile Height measure is the value of a distance Solibri analysisBottom Area Total area of the cross section (or profile) of the beam. The exact definition
and calculation rules depend on the method of measurement used.Solibri analysis
Volume A volume measure is the value of the solid content of a body Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to
place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)
Solibri analysis
Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)
Solibri analysis
Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)
Solibri analysis
Name Description Value TypeNominalLength Total nominal length of the beam, not taking into account any cut-out's or
other processing features.IfcQuantityLength
CrossSectionArea Total area of the cross section (or profile) of the beam. The exact definitionand calculation rules depend on the method of measurement used.
IfcQuantityArea
OuterSurfaceArea Total area of the extruded surfaces of the beam (not taking into account theend cap areas), normally generated as perimeter * length.
IfcQuantityArea
TotalSurfaceArea Total area of the beam, normally generated as perimeter * length + 2 *cross section area.
IfcQuantityArea
GrossVolume Total gross volume of the beam, not taking into account possible processingfeatures (cut-out's, etc.) or openings and recesses. The exact definition andcalculation rules depend on the method of measurement used.
IfcQuantityVolume
NetVolume Total net volume of the beam, taking into account possible processingfeatures (cut-out's, etc.) or openings and recesses. The exact definition andcalculation rules depend on the method of measurement used.
IfcQuantityVolume
GrossWeight Total gross weight of the beam without add-on parts, not taking intoaccount possible processing features (cut-out's, etc.) or openings andrecesses.
IfcQuantityWeight
NetWeight Total net weight of the beam without add-on parts, taking into accountpossible processing features (cut-out's, etc.) or openings and recesses.
IfcQuantityWeight
Pset_BeamCommon
IfcBeam
Name Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierSpan Clear span for this object. The shape information is provided in addition to
the shape representation and the geometric parameters used within. Incases of inconsistency between the geometric parameters and the shapeproperties, provided in the attached property, the geometric parameterstake precedence.
IfcPositiveLengthMeasure / LENGTHUNIT
Slope Slope angle - relative to horizontal (0.0 degrees). The shape information isprovided in addition to the shape representation and the geometricparameters used within. In cases of inconsistency between the geometricparameters and the shape properties, provided in the attached property, thegeometric parameters take precedence.
IfcPlaneAngleMeasure/ PLANEANGLEUNIT
IsExternal Indication whether the element is designed for use in the exterior (TRUE)or not (FALSE). If (TRUE) it is an external element and faces the outside ofthe building.
IfcBoolean
LoadBearing Indicates whether the object is intended to carry loads (TRUE) or not(FALSE).
IfcBoolean
FireRating Fire rating for this object. It is given according to the national fire safetyclassification.
IfcLabel
IfcColumnQuantities
Name Description Value TypeLenght A length measure is the value of a distance Solibri analysisBottom Area Total area of the cross section (or profile) of the column. The exact
definition and calculation rules depend on the method of measurementused.
Solibri analysis
Diameter A diameter is the value of a distance of a straight line going through thecenter of a circle connecting two points on the circumference.
Solibri analysis
Profile Height The Profile Height measure is the value of a distance Solibri analysisProfile Width The Profile Width measure is the value of a distance Solibri analysisSkin Area Perimeter x lenght (excl. bottom area and top area) Solibri analysisVolume A volume measure is the value of the solid content of a body Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to
place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)
Solibri analysis
Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)
Solibri analysis
Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)
Solibri analysis
Base Quantities
IfcColumn
Pset_ColumnCommon
Name Description Value TypeNominalLength Total nominal length of the column, not taking into account any cut-out's or
other processing features.IfcQuantityLength
CrossSectionArea Total area of the cross section (or profile) of the column. The exactdefinition and calculation rules depend on the method of measurementused.
IfcQuantityArea
OuterSurfaceArea Total area of the extruded surfaces of the column (not taking into accountthe end cap areas), normally generated as perimeter * length.
IfcQuantityArea
TotalSurfaceArea Total area of the column, normally generated as perimeter * length + 2 *cross section area.
IfcQuantityArea
GrossVolume Total gross volume of the column, not taking into account possibleprocessing features (cut-out's, etc.) or openings and recesses. The exactdefinition and calculation rules depend on the method of measurementused.
IfcQuantityVolume
NetVolume Total net volume of the column, taking into account possible processingfeatures (cut-out's, etc.) or openings and recesses. The exact definition andcalculation rules depend on the method of measurement used.
IfcQuantityVolume
GrossWeight Total gross weight of the column without add-on parts, not taking intoaccount possible processing features (cut-out's, etc.) or openings andrecesses.
IfcQuantityWeight
NetWeight Total net weight of the column without add-on parts, taking into accountpossible processing features (cut-out's, etc.) or openings and recesses.
IfcQuantityWeight
Name Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierSlope Slope angle - relative to horizontal (0.0 degrees). The shape information is
provided in addition to the shape representation and the geometricparameters used within. In cases of inconsistency between the geometricparameters and the shape properties, provided in the attached property, thegeometric parameters take precedence.
IfcPlaneAngleMeasure/ PLANEANGLEUNIT
IsExternal Indication whether the element is designed for use in the exterior (TRUE)or not (FALSE). If (TRUE) it is an external element and faces the outside ofthe building.
IfcBoolean
LoadBearing Indicates whether the object is intended to carry loads (TRUE) or not(FALSE).
IfcBoolean
FireRating Fire rating for this object. It is given according to the national fire safetyclassification.
IfcLabel
Base Quantities
IfcCoveringQuantities
Name Description Value TypeVolume A volume measure is the value of the solid content of a body Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to
place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)
Solibri analysis
Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)
Solibri analysis
Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)
Solibri analysis
Name Description Value TypeGrossArea Total area of the covering in the elevation view. The exact definition and
calculation rules depend on the method of measurement used.IfcQuantityArea
NetArea Total area of the covering in the elevation view taking into accountpossible openings. The exact definition and calculation rules depend on themethod of measurement used.
IfcQuantityArea
IfcPolyloop
Extruded Direction
IfcCoveringPset_CoveringCommon
Name Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierFireRating Fire rating for this object. It is given according to the national fire safety
classification.IfcLabel
AcousticRating Acoustic rating for this object. It is giving according to the national buildingcode. It indicates the sound transmission resistance of this object by anindex ration (instead of providing full sound absorbtion values).
IfcLabel
FlammabilityRating Flammability Rating for this object. It is given according to the nationalbuilding code that governs the rating of flammability for materials.
IfcLabel
FragilityRating Indication on the fragility of the covering (e.g., under fire conditions). It isgiven according to the national building code that might provide aclassification for fragility.
IfcLabel
SurfaceSpreadOfFlame Indication on how the flames spread around the surface, It is givenaccording to the national building code that governs the fire behaviour formaterials.
IfcLabel
Material Main material of the covering, it should only be given, if no IfcMaterialclass is assigned to the IfcCovering instance.
IfcLabel
Combustible Indication whether the object is made from combustible material (TRUE) ornot (FALSE).
IfcBoolean
TotalThickness Thickness of the covering, The thickness information is provided in additionto the shape representation and the geometric parameters used within. Incases of inconsistency between the geometric parameters and the shapeproperties, provided in the attached property, the geometric parameterstake precedence.
IfcPositiveLengthMeasure / LENGTHUNIT
Finish Finish selection for this object. Here specification of the surface finish forinformational purposes
IfcText
IfcPolyloop
Extruded Direction
IfcCurtainWallQuantities
Name Description Value TypeArea Area of the wall as viewed by an elevation view of the middle plane. It does
take into account all wall modifications (such as openings). The exactdefinition and calculation rules depend on the method of measurementused.
Solibri analysis
Area (minimum) Other side of the same wall (see Area, often the same value) Solibri analysisGross Area Area of the wall as viewed by an elevation view of the middle plane of the
wall. It does not take into account any wall modifications (such asopenings). The exact definition and calculation rules depend on the methodof measurement used.
Solibri analysis
Gross Area (minimum) Other side of the same wall (see Gross Area, often the same value) Solibri analysisArea of Doors Area of the doors in the wall as viewed by an elevation view of the middle
plane. The exact definition and calculation rules depend on the method ofmeasurement used.
Solibri analysis
Area of Windows Area of the windows in the wall as viewed by an elevation view of themiddle plane. The exact definition and calculation rules depend on themethod of measurement used.
Solibri analysis
Area of Openings Area of the openings in the wall as viewed by an elevation view of themiddle plane. The exact definition and calculation rules depend on themethod of measurement used.
Solibri analysis
Bottom Area Total area of the cross section (or profile) of the wall. The exact definitiond l l i l d d h h d f d
Solibri analysisHeight The height measure is the value of a distance Solibri analysisHeight (minimum) Lower side of the same wall (see Height, often the same value) Solibri analysisLength A length measure is the value of a distance Solibri analysisLength (minimum) Shorter side of the same wall (see Length, often the same value) Solibri analysisThickness The thickness measure is the value of a distance Solibri analysisThickness (minimum) Thinner side of the same wall (see Thickness, often the same value) Solibri analysisVolume A volume measure is the value of the solid content of a body Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to
place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)
Solibri analysis
Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)
Solibri analysis
Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)
Solibri analysis
Base Quantities
IfcCurtainWall
Pset_CurtainWallCommonName Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierAcousticRating Acoustic rating for this object. It is giving according to the national building
code. It indicates the sound transmission resistance of this object by anindex ration (instead of providing full sound absorbtion values).
IfcLabel
FireRating Fire rating given according to the national fire safety classification. IfcLabelCombustible Indication whether the object is made from combustible material (TRUE) or
not (FALSE).IfcBoolean
SurfaceSpreadOfFlame Indication on how the flames spread around the surface, It is givenaccording to the national building code that governs the fire behaviour formaterials.
IfcLabel
ThermalTransmittance Thermal transmittance coefficient (U-Value) of a material. Here the totalthermal transmittance coefficient through the wall (including all materials).
IfcThermalTransmittanceMeasure /THERMALTRANSMITTANCEUNIT
IsExternal Indication whether the element is designed for use in the exterior (TRUE)or not (FALSE). If (TRUE) it is an external element and faces the outside ofthe building.
IfcBoolean
Name Description Value Type
IfcDoorQuantities
Base Quantities
Name Description Value Type
Name Description Value TypeArea Total area of the door in the elevation view. The exact definition and
calculation rules depend on the method of measurement used.Solibri analysis
Height The height measure is the value of a distance Solibri analysisWidth The width measure is the value of a distance Solibri analysisFrame Length A length measure is the value of a distance Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to
place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)
Solibri analysis
Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)
Solibri analysis
Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)
Solibri analysis
Pset_DoorCommon
IfcDoor
Name Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierFireRating Fire rating for this object. It is given according to the national fire safety
classification.IfcLabel
AcousticRating Acoustic rating for this object. It is giving according to the national buildingcode. It indicates the sound transmission resistance of this object by anindex ration (instead of providing full sound absorbtion values).
IfcLabel
SecurityRating Index based rating system indicating security level. It is giving according tothe national building code.
IfcLabel
IsExternal Indication whether the element is designed for use in the exterior (TRUE)or not (FALSE). If (TRUE) it is an external element and faces the outside ofthe building.
IfcBoolean
Infiltration Infiltration flowrate of outside air for the filler object based on the area ofthe filler object at a pressure level of 50 Pascals. It shall be used, if thelength of all joints is unknown.
IfcVolumetricFlowRateMeasure /VOLUMETRICFLOWRATEUNIT
ThermalTransmittance Thermal transmittance coefficient (U-Value) of a material. It applies to thetotal door construction.
IfcThermalTransmittanceMeasure /THERMALTRANSMITTANCEUNIT
GlazingAreaFraction Fraction of the glazing area relative to the total area of the filling element.It shall be used, if the glazing area is not given separately for all panelswithin the filling element.
IfcPositiveRatioMeasure
HandicapAccessible Indication that this object is designed to be accessible by the handicapped.It is giving according to the requirements of the national building code.
IfcBoolean
FireExit Indication whether this object is designed to serve as an exit in the case offire (TRUE) or not (FALSE). Here it defines an exit door in accordance to thenational building code.
IfcBoolean
SelfClosing Indication whether this object is designed to close automatically after use(TRUE) or not (FALSE).
IfcBoolean
SmokeStop Indication whether the object is designed to provide a smoke stop (TRUE)or not (FALSE).
IfcBoolean
IfcFootingQuantities
Base Quantities
Name Description Value Type
Name Description Value TypeHeight The height measure is the value of a distance Solibri analysisBottom Area Total area of the cross section (or profile) of the footing. The exact
definition and calculation rules depend on the method of measurementused.
Solibri analysis
Profile Height The Profile Height measure is the value of a distance Solibri analysisProfile Width The Profile Width measure is the value of a distance Solibri analysisVolume A volume measure is the value of the solid content of a body Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to
place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)
Solibri analysis
Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)
Solibri analysis
Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)
Solibri analysis
Pset_ReinforcementBarCountOfIndependentFooting,Pset_ReinforcementBarPitchOfContinuousFooting
IfcFooting
Name Definition Data Type
Description Description of the reinforcement. IfcTextReference A descriptive label for the general reinforcement type. IfcLabelXDirectionLowerBarCount The number of bars with X direction lower bar. IfcIntegerYDirectionLowerBarCount The number of bars with Y direction lower bar. IfcIntegerXDirectionUpperBarCount The number of bars with X direction upper bar. IfcIntegerYDirectionUpperBarCount The number of bars with Y direction upper bar. IfcInteger
Description Description of the reinforcement. IfcTextReference A descriptive label for the general reinforcement type. IfcLabelCrossingUpperBarPitch The pitch length of the crossing upper bar. IfcPositiveLengthMeas
ure / LENGTHUNITCrossingLowerBarPitch The pitch length of the crossing lower bar. IfcPositiveLengthMeas
ure / LENGTHUNIT
Pset_ReinforcementBarCountOfIndependentFooting
Pset_ReinforcementBarPitchOfContinuousFooting
IfcMemberQuantities
Base Quantities
Name Description Value TypeVolume A volume measure is the value of the solid content of a body Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to
place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)
Solibri analysis
Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)
Solibri analysis
Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)
Solibri analysis
Name Description Value TypeNominalLength Total nominal length of the member, not taking into account any cut-out's
or other processing features.IfcQuantityLength
CrossSectionArea Total area of the cross section (or profile) of the member. The exactdefinition and calculation rules depend on the method of measurementused.
IfcQuantityArea
OuterSurfaceArea Total area of the extruded surfaces of the member (not taking into accountthe end cap areas), normally generated as perimeter * length.
IfcQuantityArea
TotalSurfaceArea Total area of the member, normally generated as perimeter * length + 2 *cross section area.
IfcQuantityArea
GrossVolume Total gross volume of the member, not taking into account possibleprocessing features (cut-out's, etc.) or openings and recesses. The exactdefinition and calculation rules depend on the method of measurementused.
IfcQuantityVolume
NetVolume Total net volume of the member, taking into account possible processingfeatures (cut-out's, etc.) or openings and recesses. The exact definition andcalculation rules depend on the method of measurement used.
IfcQuantityVolume
GrossWeight Total gross weight of the member without add-on parts, not taking intoaccount possible processing features (cut-out's, etc.) or openings andrecesses.
IfcQuantityWeight
NetWeight Total net weight of the member without add-on parts, taking into accountpossible processing features (cut-out's, etc.) or openings and recesses.
IfcQuantityWeight
Pset_MemberCommon
IfcMember
Name Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierSpan Clear span for this object. The shape information is provided in addition to
the shape representation and the geometric parameters used within. Incases of inconsistency between the geometric parameters and the shapeproperties, provided in the attached property, the geometric parameterstake precedence.
IfcPositiveLengthMeasure / LENGTHUNIT
Slope Slope angle - relative to horizontal (0.0 degrees). The shape information isprovided in addition to the shape representation and the geometricparameters used within. In cases of inconsistency between the geometricparameters and the shape properties, provided in the attached property, thegeometric parameters take precedence.
IfcPlaneAngleMeasure/ PLANEANGLEUNIT
IsExternal Indication whether the element is designed for use in the exterior (TRUE)or not (FALSE). If (TRUE) it is an external element and faces the outside ofthe building.
IfcBoolean
LoadBearing Indicates whether the object is intended to carry loads (TRUE) or not(FALSE).
IfcBoolean
FireRating Fire rating for this object. It is given according to the national fire safetyclassification.
IfcLabel
IfcObjectQuantities
Base Quantities
Pset_BuildingElementProxyCommon
Name Description Value TypeBottom Area Total area of the cross section (or profile) of the object. The exact definition
and calculation rules depend on the method of measurement used.Solibri analysis
Volume A volume measure is the value of the solid content of a body Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to
place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)
Solibri analysis
Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)
Solibri analysis
Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)
Solibri analysis
Name Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifier
Name Description Value Type
IfcOpeningQuantities
Base Quantities
Name Description Value TypeArea Total area of the opening in the elevation view. The exact definition and
calculation rules depend on the method of measurement used.Solibri analysis
Height The height measure is the value of a distance Solibri analysisWidth The width measure is the value of a distance Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to
place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)
Solibri analysis
Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)
Solibri analysis
Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)
Solibri analysis
Name Description Value TypeNominalArea Area of the opening as viewed by an elevation view (for wall openings) or
as viewed by a ground floor view (for floor openings). The exact definitionand calculation rules depend on the method of measurement used.
IfcQuantityArea
NominalVolume Volume of the opening. The exact definition and calculation rules depend onthe method of measurement used.
IfcQuantityVolume
IfcOpeningPset_OpeningElementCommon
Name Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierPurpose Indication of the purpose for that opening, e.g. 'ventilation', 'access', etc. IfcLabelFireExit Indication whether this object is designed to serve as an exit in the case of
fire (TRUE) or not (FALSE). Here whether the space (in case of e.g., acorridor) is designed to serve as an exit space, e.g., for fire escapepurposes.
IfcBoolean
ProtectedOpening Indication whether the opening is considered to be protected under firesafety considerations. If (TRUE) it counts as a protected opening under theapplicable building code, (FALSE) otherwise.
IfcBoolean
ParallelJambs Indicated, whether the jambs of an opening in a curved building elementare intended to be parallel (TRUE) or are radial (FALSE). Radial means, thatthe extension of the jambs are rays through the axis of the revolutionforming the curved building element.
IfcBoolean
Pset_PlateCommon
IfcPlateQuantities
Base Quantities
Name Description Value TypeVolume A volume measure is the value of the solid content of a body Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to
place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)
Solibri analysis
Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)
Solibri analysis
Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)
Solibri analysis
Name Description Value Type
Name Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierIsExternal Indication whether the element is designed for use in the exterior (TRUE)
or not (FALSE). If (TRUE) it is an external element and faces the outside ofthe building.
IfcBoolean
LoadBearing Indicates whether the object is intended to carry loads (TRUE) or not(FALSE).
IfcBoolean
AcousticRating Acoustic rating for this object. It is giving according to the national buildingcode. It indicates the sound transmission resistance of this object by anindex ration (instead of providing full sound absorbtion values).
IfcLabel
FireRating Fire rating for this object. It is given according to the national fire safetyclassification.
IfcLabel
ThermalTransmittance Thermal transmittance coefficient (U-Value) of a material. It applies to thetotal door construction.
IfcThermalTransmittanceMeasure /THERMALTRANSMITTANCEUNIT
Extruded Direction
Pset_RailingCommon
IfcRailingQuantities
Base QuantitiesName Description Value Type
Name Description Value TypeBottom Area Total area of the cross section (or profile) of the railing. The exact
definition and calculation rules depend on the method of measurementused.
Solibri analysis
Height The Height measure is the value of a distance Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to
place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)
Solibri analysis
Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)
Solibri analysis
Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)
Solibri analysis
Name Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierHeight Height of the object. It is the upper hight of the railing above the floor or
stair. The size information is provided in addition to the shaperepresentation and the geometric parameters used within. In cases ofinconsistency between the geometric parameters and the size properties,provided in the attached property set, the geometric parameters takeprecedence.
IfcPositiveLengthMeasure / LENGTHUNIT
Diameter Diameter of the object. It is the diameter of the handrail of the railing. Thesize information is provided in addition to the shape representation and thegeometric parameters used within. In cases of inconsistency between thegeometric parameters and the size properties, provided in the attachedproperty set, the geometric parameters take precedence. Here the diameterof the hand or guardrail within the railing.
IfcPositiveLengthMeasure / LENGTHUNIT
IsExternal Indication whether the element is designed for use in the exterior (TRUE)or not (FALSE). If (TRUE) it is an external element and faces the outside ofthe building.
IfcBoolean
IfcRampQuantities
Base QuantitiesName Description Value Type
Name Description Value TypeBottom Area Total area of the cross section (or profile) of the ramp. The exact definition
and calculation rules depend on the method of measurement used.Solibri analysis
Volume A volume measure is the value of the solid content of a body Solibri analysisHeight The height measure is the value of a distance Solibri analysisAngle Angle of the object - relative to horizontal (0.0 degrees) Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to
place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)
Solibri analysis
Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)
Solibri analysis
Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)
Solibri analysis
IfcRampPset_RampCommon
Name Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierRequiredHeadroom Required headroom clearance for the passageway according to the
applicable building code or additional requirements.IfcPositiveLengthMeasure / LENGTHUNIT
RequiredSlope Required sloping angle of the object - relative to horizontal (0.0 degrees).Required maximum slope for the passageway according to the applicablebuilding code or additional requirements
IfcPlaneAngleMeasure/ PLANEANGLEUNIT
IsExternal Indication whether the element is designed for use in the exterior (TRUE)or not (FALSE). If (TRUE) it is an external element and faces the outside ofthe building.
IfcBoolean
FireRating Fire rating for this object. It is given according to the national fire safetyclassification.
IfcLabel
FireExit Indication whether this object is designed to serve as an exit in the case offire (TRUE) or not (FALSE). Here it defines an exit ramp in accordance tothe national building code.
IfcBoolean
HandicapAccessible Indication that this object is designed to be accessible by the handicapped.Set to (TRUE) if this ramp is rated as handicap accessible according thelocal building codes, otherwise (FALSE).
IfcBoolean
HasNonSkidSurface Indication whether the surface finish is designed to prevent slippery (TRUE)or not (FALSE).
IfcBoolean
IfcRoofQuantities
Base Quantities
Name Description Value TypeArea Total area of the roof in the elevation view taking into account
possible openings. The exact definition and calculation rules depend on themethod of measurement used.
Solibri analysis
Perimeter The perimeter measure is the value of a distance Solibri analysisThickness The thickness measure is the value of a distance Solibri analysisVolume A volume measure is the value of the solid content of a body Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to
place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)
Solibri analysis
Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)
Solibri analysis
Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)
Solibri analysis
Name Description Value TypeTotalSurfaceArea Total (exposed to the outside) area of all roof slabs belonging to the roof.
The exact definition and calculation rules depend on the method ofmeasurement used.
IfcQuantityArea
LocalPlacements of IfcSlab
LocalPlacements of IfcRoof
IfcRoofPset_RoofCommon
Name Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierFireRating Fire rating for this object. It is given according to the national fire safety
classification.IfcLabel
IsExternal Indication whether the element is designed for use in the exterior (TRUE)or not (FALSE). If (TRUE) it is an external element and faces the outside ofthe building.
IfcBoolean
ProjectedArea Area of the roof projected onto a 2D horizontal plane IfcAreaMeasure /AREAUNIT
TotalArea Total exposed area of the roof IfcAreaMeasure /AREAUNIT
LocalPlacements of IfcSlab
LocalPlacements of IfcRoof
IfcSlabQuantities
Name Description Value TypeArea Total area of the extruded area of the slab, taking into account possible
slab openings. The exact definition and calculation rules depend on themethod of measurement used.
Solibri analysis
Gross Area Total area of the extruded area of the slab. The exact definition andcalculation rules depend on the method of measurement used.
Solibri analysis
Area of Openings Total area of openings. Solibri analysisPerimeter The perimeter measure of the slab is the value of a distance Solibri analysisPerimeter of Openings The perimeter measure of the openings in the slab is the value of a
distanceSolibri analysis
Thickness The thickness measure is the value of a distance Solibri analysisVolume A volume measure is the value of the solid content of a body Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to
place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)
Solibri analysis
Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)
Solibri analysis
Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)
Solibri analysis
Extruded Direction
IfcSlab
Pset_SlabCommon
Base Quantities
Name Description Value TypeNominalWidth Total nominal (or average) width (or thickness) of the slab. The exact
definition and calculation rules depend on the method of measurementused.
IfcQuantityLength
Perimeter Perimeter measured along the outer boundaries of the slab. The exactdefinition and calculation rules depend on the method of measurementused.
IfcQuantityLength
GrossArea Total area of the extruded area of the slab. The exact definition andcalculation rules depend on the method of measurement used.
IfcQuantityArea
NetArea Total area of the extruded area of the slab, taking into account possibleslab openings. The exact definition and calculation rules depend on themethod of measurement used.
IfcQuantityArea
GrossVolume Total gross volume of the slab, not taking into account possible openingsand recesses. The exact definition and calculation rules depend on themethod of measurement used.
IfcQuantityVolume
NetVolume Total net volume of the slab, taking into account possible openings andrecesses. The exact definition and calculation rules depend on the methodof measurement used.
IfcQuantityVolume
GrossWeight Total gross weight of the slab, not taking into account possible openingsand recesses or projections. The exact definition and calculation rulesdepend on the method of measurement used.
IfcQuantityWeight
NetWeight Total net weight of the slab, taking into account possible openings andrecesses or projections. The exact definition and calculation rules dependon the method of measurement used.
IfcQuantityWeight
Name Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierAcousticRating Acoustic rating for this object. It is giving according to the national building
code. It indicates the sound transmission resistance of this object by anindex ration (instead of providing full sound absorbtion values
IfcLabel
FireRating Fire rating for this object. It is given according to the national fire safetyclassification.
IfcLabel
Combustible Indication whether the object is made from combustible material (TRUE) ornot (FALSE).
IfcBoolean
SurfaceSpreadOfFlame Indication on how the flames spread around the surface, It is givenaccording to the national building code that governs the fire behaviour formaterials.
IfcLabel
ThermalTransmittance Thermal transmittance coefficient (U-Value) of a material. Here the totalthermal transmittance coefficient through the slab (including all materials).
IfcThermalTransmittanceMeasure /THERMALTRANSMITTANCEUNIT
IsExternal Indication whether the element is designed for use in the exterior (TRUE)or not (FALSE). If (TRUE) it is an external element and faces the outside ofthe building
IfcBoolean
LoadBearing Indicates whether the object is intended to carry loads (TRUE) or not(FALSE).
IfcBoolean
Compartmentation Indication whether the object is designed to serve as a firecompartmentation (TRUE) or not (FALSE).
IfcBoolean
PitchAngle Angle of the slab to the horizontal when used as a component for the roof(specified as 0 degrees or not asserted for cases where the slab is not usedas a roof component).
IfcPlaneAngleMeasure/ PLANEANGLEUNIT
Extruded Direction
IfcSpaceQuantities
Name Description Value TypeArea Total area of the extruded area of the space, taking into account possible
space openings. The exact definition and calculation rules depend on themethod of measurement used.
Solibri analysis
Height The height measure is the value of a distance Solibri analysisPerimeter The perimeter measure of the space is the value of a distance Solibri analysisArea of Doors Total area of doors Solibri analysisArea of Windows Total area of windows Solibri analysisVolume A volume measure is the value of the solid content of a body Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to
place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)
Solibri analysis
Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)
Solibri analysis
Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)
Solibri analysis
IfcSpaceBase Quantities
Name Description Value TypeNominalHeight Floor Height (without flooring) to Ceiling height (without suspended ceiling)
for this space (measured from top of slab of this space to the bottom of slabof space above); the average shall be taken if room shape is not prismatic.
IfcQuantityLength
ClearHeight Clear Height between floor level (including finish) and ceiling level(including finish and sub construction) of this space; the average shall betaken if room shape is not prismatic.
IfcQuantityLength
GrossPerimeter Calculated gross perimeter at the floor level of this space. It all sides of thespace, including those parts of the perimeter that are created by virtualboundaries and openings. The exact definition and calculation rules dependon the method of measurement used.
IfcQuantityLength
NetPerimeter Calculated net perimeter at the floor level of this space. It normallyexcludes those parts of the perimeter that are created by by virtualboundaries and openings. The exact definition and calculation rules dependon the method of measurement used.
IfcQuantityLength
GrossFloorArea Calculated sum of all floor areas covered by the space. It normally includesthe area covered by elementsinside the space (columns, inner walls, etc.).The exact definition and calculation rules depend on the method ofmeasurement used.
IfcQuantityArea
NetFloorArea Calculated sum of all usable floor areas covered by the space. It normallyexcludes the area covered by elements inside the space (columns, innerwalls, etc.), floor openings, or other protruding elements. Special rulesapply for areas that have a low headroom. The exact definition andcalculation rules depend on the method of measurement used.
IfcQuantityArea
GrossCeilingArea Calculated sum of all ceiling areas of the space. It normally includes thearea covered by elementsinside the space (columns, inner walls, etc.). Theceiling area is the real (and not the projected) area (e.g. in case of slopedceilings). The exact definition and calculation rules depend on the methodof measurement used.
IfcQuantityArea
NetCeilingArea Calculated sum of all ceiling areas covered by the space. It normallyexcludes the area covered by elements inside the space (columns, innerwalls, etc.) or by ceiling openings. The ceiling area is the real (and not theprojected) area (e.g. in case of sloped ceilings). The exact definition andcalculation rules depend on the method of measurement used.
IfcQuantityArea
GrossWallArea Calculated sum of all wall areas bounded by the space. It normally includesthe area covered by elementsinside the wall area (doors, windows, otheropenings, etc.). The exact definition and calculation rules depend on themethod of measurement used.
IfcQuantityArea
NetWallArea Calculated sum of all wall areas bounded by the space. It normally excludesthe area coveredby elements inside the wall area (doors, windows, otheropenings, etc.). Special rules apply for areas that have a low headroom.The exact definition and calculation rules depend on the method ofmeasurement used.
IfcQuantityArea
GrossVolume Calculated gross volume of all areas enclosed by the space (normallyincluding the volume of construction elements inside the space). The exactdefinition and calculation rules depend on the method of measurementused.
IfcQuantityVolume
NetVolume Calculated net volume of all areas enclosed by the space (normallyexcluding the volume of construction elements inside the space). The exactdefinition and calculation rules depend on the method of measurementused.
IfcQuantityVolume
IfcSpacePset_SpaceCommon
Name Definition Data Type
Reference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierCategory Category of space usage or utilization of the area. It is defined according to
the presiding national building code.IfcLabel
FloorCovering Label to indicate the material or finish of the space flooring. The label isused for room book information and often displayed in room stamp.
IfcLabel
WallCovering Label to indicate the material or finish of the space flooring. The label isused for room book information and often displayed in room stamp.
IfcLabel
CeilingCovering Label to indicate the material or finish of the space flooring. The label isused for room book information and often displayed in room stamp.
IfcLabel
SkirtingBoard Label to indicate the material or construction of the skirting board aroundthe space flooring. The label is used for room book information and oftendisplayed in room stamp.
IfcLabel
GrossPlannedArea Total planned area for the space. Used for programming the space. IfcAreaMeasure /AREAUNIT
NetPlannedArea IfcAreaMeasure /AREAUNIT
PubliclyAccessible Indication whether this space (in case of e.g., a toilet) is designed to serveas a publicly accessible space, e.g., for a public toilet (TRUE) or not(FALSE).
IfcBoolean
HandicapAccessible Indication whether this space (in case of e.g., a toilet) is designed to serveas an accessible space for handicapped people, e.g., for a public toilet(TRUE) or not (FALSE). This information is often used to declare the needfor access for the disabled and for special design requirements of thisspace.
IfcBoolean
ConcealedFlooring Indication whether this space is declared to be a concealed flooring (TRUE)or not (FALSE). A concealed flooring is normally meant to be the spacebeneath a raised floor.
IfcBoolean
ConcealedCeiling Indication whether this space is declared to be a concealed ceiling (TRUE)or not (FALSE). A concealed ceiling is normally meant to be the spacebetween a slab and a suspended ceiling.
IfcBoolean
Pset_SpaceCommon
IfcSpacePset_SpaceFireSafetyRequirements, Pset_SpaceLightingRequirements,Pset_SpaceOccupancyRequirements
MainFireUse Main fire use for the space which is assigned from the fire use classificationtable as given by the relevant national building code.
IfcLabel
AncillaryFireUse Ancillary fire use for the space which is assigned from the fire useclassification table as given by the relevant national building code.
IfcLabel
FireRiskFactor Fire Risk factor assigned to the space according to local buildingregulations.
IfcLabel
FireHazardFactor Fire hazard code of the space. The coding depends on the national firesafety regulations.
IfcLabel
FlammableStorage Indication whether the space is intended to serve as a storage of flammablematerial (which is regarded as such by the presiding building code. (TRUE)indicates yes, (FALSE) otherwise.
IfcBoolean
FireExit Indication whether this object is designed to serve as an exit in the case offire (TRUE) or not (FALSE). Here whether the space (in case of e.g., acorridor) is designed to serve as an exit space, e.g., for fire escapepurposes.
IfcBoolean
SprinklerProtection Indication whether the space is sprinkler protected (TRUE) or not (FALSE). IfcBooleanSprinklerProtectionAutomatic Indication whether the space has an automatic sprinkler protection (TRUE)
or not (FALSE). It should only be given, if the property "SprinklerProtection"is set to TRUE.
IfcBoolean
AirPressurization Indication whether the space is required to have pressurized air (TRUE) ornot (FALSE).
IfcBoolean
ArtificialLighting Indication whether this space requires artificial lighting (as natural lightingwould be not sufficient). (TRUE) indicates yes (FALSE) otherwise.
IfcBoolean
Illuminance Required average illuminance value for this space. IfcIlluminanceMeasure / ILLUMINANCEUNIT
OccupancyType Occupancy type for this object. It is defined according to the presidingnational building code.
IfcLabel
OccupancyNumber Number of people required for the activity assigned to this space. IfcCountMeasureOccupancyNumberPeak Maximal number of people required for the activity assigned to this space in
peak time.IfcCountMeasure
OccupancyTimePerDay The amount of time during the day that the activity is required within thisspace.
IfcTimeMeasure /TIMEUNIT
AreaPerOccupant Design occupancy loading for this type of usage assigned to this space. IfcAreaMeasure /AREAUNIT
MinimumHeadroom Headroom required for the activity assigned to this space. IfcLengthMeasure /LENGTHUNIT
IsOutlookDesirable An indication of whether the outlook is desirable (set TRUE) or not (setFALSE)
IfcBoolean
Pset_SpaceFireSafetyRequirements
Pset_SpaceLightingRequirements
Pset_SpaceOccupancyRequirements
IfcSpacePset_SpaceThermalRequirements
SpaceTemperatureMax Temperature of the space or zone, that is required from user/designer viewpoint. If no summer or winter space temperature requirements are given, itapplies all year, otherwise for the intermediate period.
IfcThermodynamicTemperatureMeasure /THERMODYNAMICTEMPERATUREUNIT
SpaceTemperatureMin Minimal temperature of the space or zone, that is required fromuser/designer view point. If no summer or winter space temperaturerequirements are given, it applies all year, otherwise for the intermediateperiod.
IfcThermodynamicTemperatureMeasure /THERMODYNAMICTEMPERATUREUNIT
SpaceTemperatureSummerMax Maximal temperature of the space or zone for the hot (summer) period, thatis required from user/designer view point.
IfcThermodynamicTemperatureMeasure /THERMODYNAMICTEMPERATUREUNIT
SpaceTemperatureSummerMin Minimal temperature of the space or zone for the hot (summer) period, thatis required from user/designer view point.
IfcThermodynamicTemperatureMeasure /THERMODYNAMICTEMPERATUREUNIT
SpaceTemperatureWinterMax Maximal temperature of the space or zone for the cold (winter) period, thatis required from user/designer view point.
IfcThermodynamicTemperatureMeasure /THERMODYNAMICTEMPERATUREUNIT
SpaceTemperatureWinterMin Minimal temperature of the space or zone for the cold (winter) period, thatis required from user/designer view point.
IfcThermodynamicTemperatureMeasure /THERMODYNAMICTEMPERATUREUNIT
SpaceHumidity Humidity of the space or zone that is required from user/designer viewpoint. If no summer or winter space humidity requirements are given, itapplies all year, otherwise for the intermediate period.
IfcRatioMeasure
SpaceHumiditySummer Humidity of the space or zone for the hot (summer) period, that is requiredfrom user/designer view point.
IfcRatioMeasure
SpaceHumidityWinter Humidity of the space or zone for the cold (winter) period that is requiredfrom user/designer view point.
IfcRatioMeasure
DiscontinuedHeating Indication whether discontinued heating is required/desirable fromuser/designer view point. (TRUE) if yes, (FALSE) otherwise.
IfcBoolean
NaturalVentilation Indication whether the space is required to have natural ventilation (TRUE)or mechanical ventilation (FALSE).
IfcBoolean
NaturalVentilationRate Indication of the requirement of a particular natural air ventilation rate,given in air changes per hour.
IfcCountMeasure
MechanicalVentilationRate Indication of the requirement of a particular mechanical air ventilation rate,given in air changes per hour.
IfcCountMeasure
AirConditioning Indication whether this space requires air conditioning provided (TRUE) ornot (FALSE).
IfcBoolean
AirConditioningCentral Indication whether the space requires a central air conditioning provided(TRUE) or not (FALSE). It should only be given, if the property"AirConditioning" is set to TRUE.
IfcBoolean
Pset_SpaceThermalRequirements
IfcSpacePset_SpaceThermalDesign
CoolingDesignAirflow The air flowrate required during the peak cooling conditions. IfcVolumetricFlowRateMeasure /VOLUMETRICFLOWRATEUNIT
HeatingDesignAirflow The air flowrate required during the peak heating conditions, but could alsobe determined by minimum ventilation requirement or minimum air changerequirements.
IfcVolumetricFlowRateMeasure /VOLUMETRICFLOWRATEUNIT
TotalSensibleHeatGain The total sensible heat or energy gained by the space during the peakcooling conditions.
IfcPowerMeasure /POWERUNIT
TotalHeatGain The total amount of heat or energy gained by the space at the time of thespace's peak cooling conditions.
IfcPowerMeasure /POWERUNIT
TotalHeatLoss The total amount of heat or energy lost by the space at the time of thespace's peak heating conditions.
IfcPowerMeasure /POWERUNIT
CoolingDryBulb Inside dry bulb temperature for cooling design IfcThermodynamicTemperatureMeasure /THERMODYNAMICTEMPERATUREUNIT
CoolingRelativeHumidity Inside relative humidity for cooling design. IfcPositiveRatioMeasure
HeatingDryBulb Inside dry bulb temperature for heating design IfcThermodynamicTemperatureMeasure /THERMODYNAMICTEMPERATUREUNIT
HeatingRelativeHumidity Inside relative humidity for heating design. IfcPositiveRatioMeasure
VentilationAirFlowrate Ventilation outside air requirement for the space. IfcVolumetricFlowRateMeasure /VOLUMETRICFLOWRATEUNIT
ExhaustAirFlowrate Design exhaust air flow rate for the space. IfcVolumetricFlowRateMeasure /VOLUMETRICFLOWRATEUNIT
CeilingRAPlenum Ceiling plenum used for return air or not. TRUE = Yes, FALSE = No. IfcBooleanBoundaryAreaHeatLoss Heat loss per unit area for the boundary object. This is a design input value
for use in the absence of calculated load data.IfcHeatFluxDensityMeasure /HEATFLUXDENSITYUNIT
Pset_SpaceThermalDesign
Base Quantities
IfcStairQuantities
Name Description Value TypeBottom Area Total area of the cross section (or profile) of the stair. The exact definition
and calculation rules depend on the method of measurement used.Solibri analysis
Volume A volume measure is the value of the solid content of a body Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to
place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)
Solibri analysis
Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)
Solibri analysis
Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)
Solibri analysis
Name Description Value Type
IfcStairPset_StairCommon
Name Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierNumberOfRiser Total number of the risers included in the stair IfcCountMeasureNumberOfTreads Total number of treads included in the stair IfcCountMeasureRiserHeight Vertical distance from tread to tread. The riser height is supposed to be
equal for all steps of a stair or stair flight.IfcPositiveLengthMeasure / LENGTHUNIT
TreadLength Horizontal distance from the front of the thread to the front of the nexttread. The tread length is supposed to be equal for all steps of the stair orstair flight at the walking line.
IfcPositiveLengthMeasure / LENGTHUNIT
RequiredHeadroom Required headroom clearance for the passageway according to theapplicable building code or additional requirements
IfcPositiveLengthMeasure / LENGTHUNIT
HandicapAccessible Indication that this object is designed to be accessible by the handicapped.Set to (TRUE) if this stair is rated as handicap accessible according thelocal building codes, otherwise (FALSE). Accessibility maybe provided byadditional means.
IfcBoolean
IsExternal Indication whether the element is designed for use in the exterior (TRUE)or not (FALSE). If (TRUE) it is an external element and faces the outside ofthe building.
IfcBoolean
FireRating Fire rating for this object. It is given according to the national fire safetyclassification.
IfcLabel
FireExit Indication whether this object is designed to serve as an exit in the case offire (TRUE) or not (FALSE). Here it defines an exit stair in accordance to thenational building code.
IfcBoolean
HasNonSkidSurface Indication whether the surface finish is designed to prevent slippery (TRUE)or not (FALSE).
IfcBoolean
Base Quantities
IfcSuspendedCeilingQuantities
Name Description Value TypeArea Total area of the covering in the elevation view taking into account
possible openings. The exact definition and calculation rules depend on themethod of measurement used.
Solibri analysis
Thickness The thickness measure is the value of a distance Solibri analysisVolume A volume measure is the value of the solid content of a body Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to
place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)
Solibri analysis
Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)
Solibri analysis
Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)
Solibri analysis
Name Description Value TypeGrossArea Total area of the covering in the elevation view. The exact definition and
calculation rules depend on the method of measurement used.IfcQuantityArea
NetArea Total area of the covering in the elevation view taking into accountpossible openings. The exact definition and calculation rules depend on themethod of measurement used.
IfcQuantityArea
IfcSuspendedCeilingPset_CoveringCommon
Name Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierFireRating Fire rating for this object. It is given according to the national fire safety
classification.IfcLabel
AcousticRating Acoustic rating for this object. It is giving according to the national buildingcode. It indicates the sound transmission resistance of this object by anindex ration (instead of providing full sound absorbtion values).
IfcLabel
FlammabilityRating Flammability Rating for this object. It is given according to the nationalbuilding code that governs the rating of flammability for materials.
IfcLabel
FragilityRating Indication on the fragility of the covering (e.g., under fire conditions). It isgiven according to the national building code that might provide aclassification for fragility.
IfcLabel
SurfaceSpreadOfFlame Indication on how the flames spread around the surface, It is givenaccording to the national building code that governs the fire behaviour formaterials.
IfcLabel
Material Main material of the covering, it should only be given, if no IfcMaterialclass is assigned to the IfcCovering instance.
IfcLabel
Combustible Indication whether the object is made from combustible material (TRUE) ornot (FALSE).
IfcBoolean
TotalThickness Thickness of the covering, The thickness information is provided in additionto the shape representation and the geometric parameters used within. Incases of inconsistency between the geometric parameters and the shapeproperties, provided in the attached property, the geometric parameterstake precedence.
IfcPositiveLengthMeasure / LENGTHUNIT
Finish Finish selection for this object. Here specification of the surface finish forinformational purposes
IfcText
IfcWallQuantities
Name Description Value TypeArea Area of the wall as viewed by an elevation view of the middle plane. It does
take into account all wall modifications (such as openings). The exactdefinition and calculation rules depend on the method of measurementused.
Solibri analysis
Area (minimum) Other side of the same wall (see Area, often the same value) Solibri analysisGross Area Area of the wall as viewed by an elevation view of the middle plane of the
wall. It does not take into account any wall modifications (such asopenings). The exact definition and calculation rules depend on the methodof measurement used.
Solibri analysis
Gross Area (minimum) Other side of the same wall (see Gross Area, often the same value) Solibri analysisArea of Doors Area of the doors in the wall as viewed by an elevation view of the middle
plane. The exact definition and calculation rules depend on the method ofmeasurement used.
Solibri analysis
Area of Windows Area of the windows in the wall as viewed by an elevation view of themiddle plane. The exact definition and calculation rules depend on themethod of measurement used.
Solibri analysis
Area of Openings Area of the openings in the wall as viewed by an elevation view of themiddle plane. The exact definition and calculation rules depend on themethod of measurement used.
Solibri analysis
Bottom Area Total area of the cross section (or profile) of the wall. The exact definitionand calculation rules depend on the method of measurement used.
Solibri analysis
Height The height measure is the value of a distance Solibri analysisHeight (minimum) Other side of the same wall (see Height, often the same value) Solibri analysisLength A length measure is the value of a distance Solibri analysisLength (minimum) Other side of the same wall (see Length, often the same value) Solibri analysisThickness The thickness measure is the value of a distance Solibri analysisThickness (minimum) Other side of the same wall (see Thickness, often the same value) Solibri analysisVolume A volume measure is the value of the solid content of a body Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to
place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)
Solibri analysis
Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)
Solibri analysis
Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)
Solibri analysis
IfcWall
Base QuantitiesName Description Value TypeNominalLength Total nominal (or average) length of the wall along the wall path. The exact
definition and calculation rules depend on the method of measurementused.
IfcQuantityLength
NominalWidth Total nominal (or average) width (or thickness) of the wall perpendicular tothe wall path. The exact definition and calculation rules depend on themethod of measurement used.
IfcQuantityLength
NominalHeight Total nominal (or average) height of the wall along the wall path. The exactdefinition and calculation rules depend on the method of measurementused.
IfcQuantityLength
GrossFootprintArea Area of the wall as viewed by a ground floor view, not taking any wallmodifications (like recesses) into account. It is also referred to as the footprint of the wall. The exact definition and calculation rules depend on themethod of measurement used.
IfcQuantityArea
NetFootprintArea Area of the wall as viewed by a ground floor view, taking all wallmodifications (like recesses) into account. It is also referred to as the footprint of the wall. The exact definition and calculation rules depend on themethod of measurement used.
IfcQuantityArea
GrossSideArea Area of the wall as viewed by an elevation view of the middle plane of thewall. It does not take into account any wall modifications (such asopenings). The exact definition and calculation rules depend on the methodof measurement used.
IfcQuantityArea
NetSideArea Area of the wall as viewed by an elevation view of the middle plane. It doestake into account all wall modifications (such as openings). The exactdefinition and calculation rules depend on the method of measurementused.
IfcQuantityArea
GrossSideAreaLeft Area of the wall as viewed by an elevation view of the left side (whenviewed along the wall path orientation). It does not take into account anywall modifications (such as openings). The exact definition and calculationrules depend on the method of measurement used.
IfcQuantityArea
NetSideAreaLeft Area of the wall as viewed by an elevation view of the left side (whenviewed along the wall path orientation). It does take into account all wallmodifications (such as openings). The exact definition and calculation rulesdepend on the method of measurement used.
IfcQuantityArea
GrossSideAreaRight Area of the wall as viewed by an elevation view of the right side (whenviewed along the wall path orientation). It does not take into account anywall modifications (such as openings). The exact definition and calculationrules depend on the method of measurement used.
IfcQuantityArea
NetSideAreaRight Area of the wall as viewed by an elevation view of the right side (whenviewed along the wall path orientation). It does take into account all wallmodifications (such as openings). The exact definition and calculation rulesdepend on the method of measurement used.
IfcQuantityArea
GrossVolume Volume of the wall, without taking into account the openings and theconnection geometry. The exact definition and calculation rules depend onthe method of measurement used.
IfcQuantityVolume
NetVolume Volume of the wall, after subtracting the openings and after considering theconnection geometry. The exact definition and calculation rules depend onthe method of measurement used.
IfcQuantityVolume
IfcWall
Pset_WallCommonName Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierAcousticRating Acoustic rating for this object. It is giving according to the national building
code. It indicates the sound transmission resistance of this object by anindex ration (instead of providing full sound absorbtion values).
IfcLabel
FireRating Fire rating given according to the national fire safety classification. IfcLabelCombustible Indication whether the object is made from combustible material (TRUE) or
not (FALSE).IfcBoolean
SurfaceSpreadOfFlame Indication on how the flames spread around the surface, It is givenaccording to the national building code that governs the fire behaviour formaterials.
IfcLabel
ThermalTransmittance Thermal transmittance coefficient (U-Value) of a material. Here the totalthermal transmittance coefficient through the wall (including all materials).
IfcThermalTransmittanceMeasure /THERMALTRANSMITTANCEUNIT
IsExternal Indication whether the element is designed for use in the exterior (TRUE)or not (FALSE). If (TRUE) it is an external element and faces the outside ofthe building.
IfcBoolean
ExtendToStructure Indicates whether the object extend to the structure above (TRUE) or not(FALSE).
IfcBoolean
LoadBearing Indicates whether the object is intended to carry loads (TRUE) or not(FALSE).
IfcBoolean
Compartmentation Indication whether the object is designed to serve as a firecompartmentation (TRUE) or not (FALSE).
IfcBoolean
Base Quantities
IfcWindowQuantities
Name Description Value TypeArea Total area of the window in the elevation view. The exact definition and
calculation rules depend on the method of measurement used.Solibri analysis
Height The height measure is the value of a distance Solibri analysisWidth The width measure is the value of a distance Solibri analysisFrame Length A length measure is the value of a distance Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to
place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)
Solibri analysis
Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)
Solibri analysis
Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)
Solibri analysis
Name Description Value Type
IfcWindowPset_WindowCommon
Name Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierFireRating Fire rating for this object. It is given according to the national fire safety
classification.IfcLabel
AcousticRating Acoustic rating for this object. It is giving according to the national buildingcode. It indicates the sound transmission resistance of this object by anindex ration (instead of providing full sound absorbtion values).
IfcLabel
SecurityRating Index based rating system indicating security level. It is giving according tothe national building code.
IfcLabel
IsExternal Indication whether the element is designed for use in the exterior (TRUE)or not (FALSE). If (TRUE) it is an external element and faces the outside ofthe building.
IfcBoolean
Infiltration Infiltration flowrate of outside air for the filler object based on the area ofthe filler object at a pressure level of 50 Pascals. It shall be used, if thelength of all joints is unknown.
IfcVolumetricFlowRateMeasure /VOLUMETRICFLOWRATEUNIT
ThermalTransmittance Thermal transmittance coefficient (U-Value) of a material. It applies to thetotal door construction.
IfcThermalTransmittanceMeasure /THERMALTRANSMITTANCEUNIT
GlazingAreaFraction Fraction of the glazing area relative to the total area of the filling element.It shall be used, if the glazing area is not given separately for all panelswithin the filling element.
IfcPositiveRatioMeasure
SmokeStop Indication whether the object is designed to provide a smoke stop (TRUE)or not (FALSE).
IfcBoolean
Base Quantities
Quantities
IfcZone
Name Description Value Type
Name Description Value TypeArea Total area of the extruded area of the zone, taking into account possible
zone openings. The exact definition and calculation rules depend on themethod of measurement used.
Solibri analysis
Height The height measure is the value of a distance Solibri analysisPerimeter The perimeter measure of the space is the value of a distance Solibri analysisArea of Doors Total area of doors Solibri analysisArea of Windows Total area of windows Solibri analysisVolume A volume measure is the value of the solid content of a body Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to
place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)
Solibri analysis
Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)
Solibri analysis
Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)
Solibri analysis
IfcZone
IfcSpace 1 IfcSpace 2
*Also Pset_Space.... parameters can be used
IfcZonePset_ZoneCommon
Name Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierCategory Category of space usage or utilization of the area. It is defined according to
the presiding national building code.IfcLabel
GrossAreaPlanned Total planned gross area for the space. Used for programming the space. IfcAreaMeasure /AREAUNIT
NetAreaPlanned Total planned net area for the space. Used for programming the space. IfcAreaMeasure /AREAUNIT
PubliclyAccessible Indication whether this space (in case of e.g., a toilet) is designed to serveas a publicly accessible space, e.g., for a public toilet (TRUE) or not(FALSE).
IfcBoolean
HandicapAccessible Indication whether this space (in case of e.g., a toilet) is designed to serveas an accessible space for handicapped people, e.g., for a public toilet(TRUE) or not (FALSE). This information is often used to declare the needfor access for the disabled and for special design requirements of thisspace.
IfcBoolean
IfcZone
IfcSpace 1 IfcSpace 2
IJpelaar - Breda
4
Pontsteiger - Amsterdam
4
BIMvan structuur naar
de gewenste output
versie20150623
INFORMATIEIDENTIFICATION
PLATTEGROND
GEVELAANZICHTDOORSNEDE
SCHEDULE
DETAIL 1:5
3D + tags 3D + tags + 2D opmaak
LOCATION QUANTITYPSET_**COMMON
SPECIFIEK PER ENTITEIT
MANUFACTURER WARRANTY
IFC PARAMETERS - COMMON PROPERTYSET
NL-SFBBOUWLAAG
NAAM GEBOUW
RUIMTE NAAM ZONENAME2 - BOUWNUMMERZONENAME - WONINGTYPE
GROEPERING VAN RUIMTEN
SITE
PROJECTNAAM
30
§2.1.2Lokale positie en orientatie
RVB BIM NORM V1.1
§2.2.7.2Terrein
§2.2.4Bestandsformaat- en naam
§2.2.7.1Project
§2.1.2Lokale positie en orientatie
§2.2.6.4ObjectGUID
§2.1.4Entiteiten
§2.2.7.7Groepering van ruimten
§2.2.7.3Bouwwerk
§2.2.6.2Informatie- indeling
§2.2.7.8Elementen
§2.1.9Bouwlaagindeling
§2.2.6.3Objectrelaties
§2.1.5Nauwkeurigheid
§2.2.7.6Ruimte
§2.1.2Lokale positie en orientatie
<bouwlaagnummer><verdiepingsoort>
<spatie><tekstuele beschrijving>
IFC 2X3 NL-SfB codering NEN 2574
www.duravermeer.nl
DURA VERMEER DIVISIE BOUW EN VASTGOED BV
De Bouw 793991 SX HoutenT (030) 288 16 [email protected]