dball-dball2-tl2-rsr en ig zb · 2017-08-28 · 7 with the exception of the obdii diagnostic...
TRANSCRIPT
SmartStart CompatibleSmartStart is equipped with D2D which means it can be connected to an interface module and used in, RemoteStart Ready ( ) mode the use of See the section for moreRSR without a remote starter. Module Programminginformation.
Installation Guide
Update Alert: Firmware updates are posted the web on a regular basis. We recommendon
that you check for firmware and/or install guide updates prior to installing this product.
Remote Start Ready ( ) is a function that enables the interface module to remote start the vehicleRSRcompletely on its own. Consequently, there is no need for an aftermarket or an remote starter in order toOEMstart the vehicle from a distance.
Important!This product is compatible with vehicles equipped with a manual transmission.NOT
The 2 firmware for 2 is an all-in-one door lock and override module compatible with specificTL DBALLToyota, and Lexus vehicles. This guide supports the installation of a 2 in Remote Start ReadyDBALL( ) mode o . This solution offers three (3)RSR with or without a Plug & Play T-Harness ( ptional)configuration options to control your system: 3x Lock Remote Start Activation, System orOEM RFSmartStart (all sold separately).
This module can only be flashed and configured using Xpress at www.directechs.com or using the DirectechsVIPMobile application for smartphones. Refer to for more information.the Module Programming section non page
• If the vehicle is already equipped with an OEM remote starter, the installer must disconnect it before installing theDBALL otherwise it will not program.• No takeover feature is available on Push-to-Start vehicles.
® Toyota Lexus are registered trademarks and property of .and their respective companies
IndexVehicle Application Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 02
OEM Remote Starter Detection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 03
Installation s s(Wiring Diagram & Vehicle Wiring Reference Chart )
Type 1 with T-Harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 04Type 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 05Type 2 with T-Harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 07Type 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 08Type 3 with T-Harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Type 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Type 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13SmartStart/ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15XL202 Installation Notes
Programming
Module Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Module Reset & Hard Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Feature & Option List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Feature Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
LED Diagnostics & Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Parking Light Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Limited One-Year Consumer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Warranty
Quick Reference Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Rev.: 20170825
Platform: DBALL2
Firmware: TL2 Remote Start Ready Installation(RSR)
© 2017 Directed. All rights reserved.
Vehicle Application GuidePage 2
The following table lists the vehicles and features which are compatible with this product. The number assigned to each yearallows you to determine which installation type should be used for your vehicle.
Rev.: 20170825
Platform: DBALL2
Firmware: TL2 Remote Start Ready Installation(RSR)
© 2017 Directed. All rights reserved.
Vehicles 2017
2016
2015
2014
2013
2012
2011
2010
2009
PK
-Im
mobili
zer
Bypass-D
ata
No
Key
Req'd
AV
-Auto
Headla
mp
Shuto
ff
DL-A
rmF
acto
ryS
ecurity
DL-D
isarm
Facto
ryS
ecurity
DL-D
oor
Lock
Contr
ol
DL-D
oor
Unlo
ck
DL-D
river
Priority
Unlo
ck
DL-H
atc
hG
lass
Rele
ase
DL-S
lidin
gD
oor
Contr
olD
river
DL-S
lidin
gD
oor
Contr
olP
assenger
DL-T
runk
/H
atc
hR
ele
ase
RS
-3x
LO
CK
ST
AR
T(S
tart
contr
olusin
gO
EM
Rem
ote
)
RS
-3x
LO
CK
ST
OP
(Sto
pcontr
olusin
gO
EM
Rem
ote
)
RS
-Rem
ote
Sta
rtR
eady
PT
SIg
n-R
FT
D
RS
-Sm
art
Sta
rt
RS
-Tach
/R
PM
Outp
ut
SS
-Entr
yM
onitoring
ALL
Door
Pin
s
SS
-Entr
yM
onitoring
Hood
Pin
SS
-Entr
yM
onitoring
Tru
nk/H
atc
hP
in
SS
-Facto
ryA
larm
Trigger
Monitoring
ST
-Bra
ke
Sta
tus
(foot
bra
ke)
ST
-Door
Locks
Sta
tus
ST
-Ignitio
nS
tatu
s
Lexus
CT 200h (Smart Key) 3 3 3 3 3 3 3 • • • • • • • • • • • • • • • • • • • •
GX 460 (Smart Key) 2 2 2 2 2 2 2 2 • • • • • • • • • • • • • • • • • • • •
HS 250h (Smart Key) 3 3 3 • • • • • • • • • • • • • • • • • • • •
RX 350 (Smart Key) 2 2 2 2 2 2 • • • • • • • • • • • • • • • • • • • •
RX 450h (Smart Key) 2 2 2 2 2 2 • • • • • • • • • • • • • • • • • • • •
Toyota
4Runner (Smart Key) 2 2 2 2 2 2 2 2 • • • • • • • • • • • • • • • • • • • •
Prius (Smart Key) 3 3 3 3 3 • • • • • • • • • • • • • • • • • • • •
Prius v (Smart Key) 4 3 3 3 3 3 • • • • • • • • • • • • • • • • • • • •
Sienna (Smart Key) 2 2 2 2 2 2 2 • • • • • • • • • • • • • • • • • • • • • •
Venza (Smart Key) 1 1 1 1 1 1 1 1 • • • • • • • • • • • • • • • • • • • •
Legend:
AV: Horn & Light Controls
CC: Comfort & Convenience Controls
DL: OE Door Lock & Alarm Controls
FOB: Sync CAN Interface w / FOB Remote
PK: Transponder & Immobilizer Override
RS: Remote Start & Engine Controls
SS: Integrated Security & Monitoring
ST: Function/Feature Status
Page 3
Rev.: 20170825
Platform: DBALL2
Firmware: TL2 Remote Start Ready Installation(RSR)
© 2017 Directed. All rights reserved.
Important OEM Remote Starter Information
If the vehicle has an active OEM remote starter it will program into convenience only (no immobilizer bypass). The reasonfor this is to allow aftermarket security to be installed while keeping the factory remote starter active. If you wish for theinterface to control the remote start sequence, perform one of the following:
If the vehicle is equipped with a physical add-on Lexus/Toyota OEM Remote StarterThe factory remote starter must be permanently disconnected before programming the Directed interface as both modulescannot coexist. See “Locating the physical OEM remote starter” chart below.
If the vehicle is equipped with a BCM enabled Lexus/Toyota OEM Remote StarterThe vehicle does not have a physical remote starter and only one module can be programed at a time. In this casetemporally disable the OEM remote start system using the following process:
1. Remove the fuse powering the OEM Remote Starter. See "Locating the fuse powering of the OEM remote starter" below.2. Perform a module reset, see page 17.3. Perform the "Module programming" steps on page 16.4. After programing is successful replace the fuse powering the OEM Remote Starter.
Important Module Programming InformationDuring "Module Programming" if the Directed interface detects an OEM Remote Starter it will direct the installer to the"Important OEM Remote Starter Information" section of the guide detailing the next steps.
Locating the fuse powering of the OEM remote starter
Make Model Fuse location Fuse Name Fuse Value
Lexus CT 200h (Smart Key) Engine room relay box, left side of engine compartment. MAYDAY 10A
Lexus GX 460 (Smart Key) Engine room relay box, left side of engine compartment. MAYDAY 7.5A
Lexus RX 350 (Smart Key) Engine room relay box, left side of engine compartment. MAYDAY/TEL 7.5A
Lexus RX 450h (Smart Key) Engine room relay box, left side of engine compartment. MAYDAY 7.5A
Locating the physical OEM remote starter
Make Model OEM Remote Starter & Connectors Location
Toyota Venza (Smart Key) Behind glove box.
Lexus RX 450h (Smart Key) Behind glove box.
Lexus RX 350 (Smart Key) Behind glove box.
Toyota 4Runner (Smart Key) Behind glove box & passenger kick panel.
Toyota Sienna (Smart Key) Behind glove box & passenger kick panel.
Lexus HS 250h (Smart Key) Behind glove box.
Prius Prius (Smart Key) Under dash panel & driver kick panel.
Lexus CT 200h Behind glove box.
Lexus GX 460 (Smart Key) Behind glove box.
Toyota Prius V (Smart Key) Behind glove box.
Page 4
BRX:Black,pin 23
Main body ECUBack side
(-) Parking Lights pin 23: ,Red
Main Body ECU(white conn. back of body ECU)
Main Body ECU(white conn. back of body ECU)
BTX:Blue,
pin 22
(-) OutputSLP : Yellow
Immo. Data 1: 10Yellow/Black:
Immo. Data 2: 11Orange/Black:
[1] : 2(-) Push-to-Start Output Green/Black:
:(-) SLP Violet, pin 4
Steering Lock(Black conn. under steering column)
1235 47 6
Important!The devices, but supplied with the .Hood Pin and Remote Start Safety Override Switch are mandatory safety are 2NOT DBALL
(-) Parking Lights Output: 4Red/Black:
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
OBDII16-pin Diagnostic Connector
(vehicle side)
TLTH2(optional)
6: (-) HoodWhite/Black:
Hood Pin
Remote Start SafetyOverride Switch
Note: Hood pin onlyrequired on vehicle notequipped with a factoryhood pin.
13 15 16 18
23 26
14 17
24 25
5 6 7 8 9 104321
12 201911
22 282721 22 23
2322 2618
107
25
13 14 16 178
21
9 11 12 15
24
1 2 3 4 5 6
2319 20
You can connect to either aXL RFTD202 aORSmartStart module.
Refer to theSmartStart/ 202XLInstallation Notes for moreinformation.
10
10
4
Installation Type 1 with T-Harness
[ ]1 Connection required only if Pit-Stop/Idle mode is desired.
14
12
RF
Prog utton. B
LED
14
12
2
DBALL2
D2Donly
[ ] S1 (-) Push-to- tart:Blue, pin 7
ENGINESTARTSTOP
BlackConnector
Connexion required only if Pit-Stop/ Idle mode is desired. (Refer toQuick Reference Guide ( )QRG atthe end of the guide .)
1345
1214 11 10 8
2
9
6
13
7
Rev.: 20170825
Platform: DBALL2
Firmware: TL2 Remote Start Ready Installation(RSR)
© 2017 Directed. All rights reserved.
Rev.: 20170825
Platform: DBALL2
Firmware: TL2 Remote Start Ready Installation(RSR)
© 2017 Directed. All rights reserved.
1 8
169
HS CAN Low pin 14: White, ( ) V+ 12 pin 16: Lt. Green,
HS CAN :High pin 6Yellow,(-) Ground pin 4,
OBDIIDiagnostic Connector
HS CAN : 3High Tan/Black:
HS CAN : 4Low Tan:
(-) Ground: 14Black:
(+) 12V Input: 13Red:
Important!The devices, but supplied with the .Hood Pin and Remote Start Safety Override Switch are mandatory safety are 2NOT DBALL
(-) Output:SLP Yellow :/Red 11
(-) Ground: Brown/Red: 12
You can connect to either a 202XLRFTD a SmartStart module.OR
Refer to the SmartStart/ 202XLInstallation Notes for more information.
6: (-) HoodWhite/Black:
Hood Pin
Remote Start SafetyOverride Switch
Note: Hood pin onlyrequired on vehicle notequipped with a factoryhood pin.
Main body ECUBack side
Immo. Data 1: 10Yellow/Black:
Immo Data 2: 11Orange/Black:
[1] : 2(-) Push-to-Start Output Green/Black:
(-) Parking Lights Output: 4Red/Black:
2322 2618
107
25
13 14 16 178
21
9 11 12 15
24
1 2 3 4 5 6
2319 20
BRX:Black,pin 23
BTX:Blue,
pin 22
13 15 16 18
23 26
14 17
24 25
5 6 7 8 9 104321
12 201911
22 282721 22 23
(-) Parking Lights pin 23: ,Red
SLP: Violet: pin 4
Steering Lock(black conn. under steering column)
1235 47 6
[ ] S1 (-) Push-to- tart:Blue, pin 7
ENGINESTARTSTOP
BlackConnector
Connexion required only if Pit-Stop/ Idle mode is desired. (Refer toQuick Reference Guide ( )QRG atthe end of the guide .)
1345
1214 11 10 8
2
9
6
13
7
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
Installation Type 1
10
14
12
10
RF
Prog utton. B
LED
4
14
12
2
2DBALL
Page 5
[ ]1 Connection required only if Pit-Stop/Idle mode is desired.
Main Body ECU(white conn. back of
body ECU) Main Body ECU(white conn. back of
body ECU)
Rev.: 20170825
Platform: DBALL2
Firmware: TL2 Remote Start Ready Installation(RSR)
© 2017 Directed. All rights reserved.
Page 6
Vehicle Wiring Reference Chart - Type 1
Wire Information Connector Information
Function Color Pin Polarity Location Color Pins
Toyota Venza (Smart Key) 2009-2016
SLP Violet 4 (-) Steering Lock Position Connector. Black 7
PTS Blue 7 (-) Push-to-Start switch. Black 14
12V Lt. Green 16 (+) OBDII. Black 16
HS CAN High Yellow 6 Data OBDII. Black 16
HS CAN Low White 14 Data OBDII. Black 16
Parking Lights Red 23 (-) Rear of Main Body ECU. White 26
BRX Black 23 Data Rear of Main Body ECU. White 28
BTX Blue 22 Data Rear of Main Body ECU. White 28
Rev.: 20170825
Platform: DBALL2
Firmware: TL2 Remote Start Ready Installation(RSR)
© 2017 Directed. All rights reserved.
Immo. Data 1: 10Yellow/Black:
Immo Data 2: 11Orange/Black:
[1] : 2(-) Push-to-Start Output Green/Black:
Important!The devices, but supplied with the .Hood Pin and Remote Start Safety Override Switch are mandatory safety are NOT DBALL2
(-) Parking Lights Output: 4Red/Black:
You can connect to either aXL RFTD202 aORSmartStart module.
Refer to theSmartStart/ 202XLInstallation Notes formore information.
OBDII16-pin Diagnostic Connector
(vehicle side)
TLTH2(optional)
(-) OutputSLP : Yellow
BRX, pin 4
BTX, pin 16
MainBodyECU
Main Body ECU(white conn. on body ECU)
1 72 83
6
9 21
22
25
10
13
23
26
11
14
29
24
27
12
15
18
20
19
4 16 28
30
SLP: Green or Lt. Blue, pin 4
Steering Lock(black conn. under steering column)
1235 47 6
[ ] S1 (-) Push-to- tart:Blue or Lt. Green, pin 7
ENGINESTARTSTOP
BlackConnector
Connexion required only if Pit-Stop/ Idle mode is desired. (Refer toQuick Reference Guide ( )QRG atthe end of the guide .)
1345
1214 11 10 8
2
9
6
13
7
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
D2Donly
10
14
12
10
RF
Prog utton. B
LED
4
14
12
2
2DBALL
Page 7
Installation Type 2 with T-Harness
[ ]1 Connection required only if Pit-Stop/Idle mode is desired.
(-) Parking lights pin 30,
Rev.: 20170825
Platform: DBALL2
Firmware: TL2 Remote Start Ready Installation(RSR)
© 2017 Directed. All rights reserved.
Important!The devices, but supplied with the .Hood Pin and Remote Start Safety Override Switch are mandatory safety are 2NOT DBALL
You can connect to either a 202XLRFTD a SmartStart module.OR
Refer to the SmartStart/ 202XLInstallation Notes for more information.
6: (-) HoodWhite/Black:
Hood Pin
Remote Start SafetyOverride Switch
Note: Hood pin onlyrequired on vehicle notequipped with a factoryhood pin.
(-) Parking Lights Output: 4Red/Black:
MainBodyECU
HS CAN : 3High Tan/Black:
HS CAN : 4Low Tan:
(-) Ground: 14Black:
(+) 12V Input: 13Red:
(-) Output:SLP Yellow :/Red 11
(-) Ground: Brown/Red: 12
BRX, pin 4
BTX, pin 16
Whiteconnector(wire side view)
1 72 83
6
9 21
22
25
10
13
23
26
11
14
29
24
27
12
15
18
20
19
4 16 28
30
1235 47 6
1 8
169
HS CAN Low pin 14: White or Red, ( ) V+ 12 pin 16:
HS CAN High pin 6: Red or Violet,(-) Ground pin 4,
OBDIIDiagnostic Connector
(-) Parking lights pin 30,
Installation Type 2
10
14
12
10
RF
Prog utton. B
LED
4
14
12
2
2DBALL
Page 8
ENGINESTARTSTOP
BlackConnector
Connexion required onlyif Pit-Stop / Idle mode isdesired. (Refer to QuickReference Guide ( )QRGat the end of the guide .)
1345
1214 11 10 8
2
9
6
13
7 Immo. Data 1: 10Yellow/Black:
Immo Data 2: 11Orange/Black:
[1] : 2(-) Push-to-Start Output Green/Black:
Steering Lock(black conn. under steering column)
SLP: Green or Lt. Blue, pin 4
[ ] S1 (-) Push-to- tart:Blue or Lt. Green, pin 7
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
[ ]1 Connection required only if Pit-Stop/Idle mode is desired.
Rev.: 20170825
Platform: DBALL2
Firmware: TL2 Remote Start Ready Installation(RSR)
© 2017 Directed. All rights reserved.
Vehicle Wiring Reference Chart - Type 2Page 9
Wire Information Connector Information
Function Color Pin Polarity Location Color Pins
Lexus GX 460 (Smart Key) 2010-2017
SLP Lt. Blue 4 (-) Steering Lock Position Connector. Black 7
PTS Lt. Green 7 (-) Push-to-Start switch. Black 14
12V Gray 16 (+) OBDII. White 16
HS CAN High Red 6 Data OBDII. White 16
HS CAN Low White 14 Data OBDII. White 16
Parking Lights White 30 (-) Main Body ECU. White 30
BRX Red 4 Data Main Body ECU. White 30
BTX Green 16 Data Main Body ECU. White 30
Lexus RX 350 (Smart Key) 2010-2015
SLP Green 4 (-) Steering Lock Position Connector. Black 7
PTS Lt. Green 7 (-) Push-to-Start switch. Black 14
12V Lt. Green 16 (+) OBDII. White 1
HS CAN High Violet 6 Data OBDII. White 16
HS CAN Low Red 14 Data OBDII. White 16
Parking Lights Violet 30 (-) Main Body ECU. White 30
BRX Pink 4 Data Main Body ECU. Black 30
BTX Lt. Green 16 Data Main Body ECU. Black 30
Lexus RX 450h (Smart Key) 2010-2015
SLP Green 4 (-) Steering Lock Position Connector. Black 7
PTS Lt. Green 7 (-) Push-to-Start switch. Black 14
12V Lt. Green 16 (+) OBDII. White 16
HS CAN High Violet 6 Data OBDII. White 16
HS CAN Low Red 14 Data OBDII. White 16
Parking Lights Violet 30 (-) Main Body ECU. White 30
BRX Pink 4 Data Main Body ECU. White 30
BTX Lt. Green 16 Data Main Body ECU. White 30
Toyota 4Runner (Smart Key) 2010-2017
SLP Lt. Blue 4 (-) Steering Lock Position Connector. Black 7
PTS Lt. Green 7 (-) Push-to-Start switch. Black 14
12V Gray 16 (+) OBDII. White 16
HS CAN High Violet 6 Data OBDII. White 16
HS CAN Low White 14 Data OBDII. White 16
Parking Lights Red 30 (-) Main Body ECU. White 30
BRX Gray 4 Data Main Body ECU. White 30
BTX White 16 Data Main Body ECU. White 30
Toyota Sienna (Smart Key) 2011-2017
SLP Green 4 (-) Steering Lock Position Connector. Black 7
PTS Blue 7 (-) Push-to-Start switch. Black 14
12V Black 16 (+) OBDII. White 16
HS CAN High Red 6 Data OBDII. White 16
HS CAN Low White 14 Data OBDII. White 16
Parking Lights Yellow 30 (-) Main Body ECU. White 30
BRX Black 4 Data Main Body ECU. White 30
BTX Blue 16 Data Main Body ECU. White 30
Rev.: 20170825
Platform: DBALL2
Firmware: TL2 Remote Start Ready Installation(RSR)
© 2017 Directed. All rights reserved.
Important!The devices, but supplied with the .Hood Pin and Remote Start Safety Override Switch are mandatory safety are 2NOT DBALL
(-) Parking Lights Output: 4Red/Black:
You can connect to either aXL RFTD202 aORSmartStart module.
Refer to theSmartStart/ 202XLInstallation Notes for moreinformation.
OBDII16-pin Diagnostic Connector
(vehicle side)
TLTH2(optional)
MainBodyECU
BRX: or pin 4Yellow Violet,
BTX: orBlue Green, pin 16
1 72 83
6
9 21
22
25
10
13
23
26
11
14
29
24
27
12
15
18
20
19
4 16 28
30
(-) Parking lights pin 30: or ,Yellow White/Black
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
Install Type with T-Harnessation 3
10
14
12
10
RF
Prog utton. B
LED
4
14
12
2
2DBALL
Page 10
D2Donly
[ ]1 Connection required only if Pit-Stop/Idle mode is desired.
Immo. Data 1: 10Yellow/Black:
Immo Data 2: 11Orange/Black:
[1] : 2(-) Push-to-Start Output Green/Black:
Main Body ECU(white conn. on body ECU)
[ ] S1 (-) Push-to- tart:Black Blue,or pin 7
ENGINESTARTSTOP
BlackConnector
1345
1214 11 10 8
2
9
6
13
7
6: (-) HoodWhite/Black:
Hood Pin
Remote Start SafetyOverride Switch
Note: Hood pin onlyrequired on vehicle notequipped with a factoryhood pin.
Connexion required onlyif Pit-Stop / Idle mode isdesired. (Refer to QuickReference Guide ( )QRGat the end of the guide .)
Rev.: 20170825
Platform: DBALL2
Firmware: TL2 Remote Start Ready Installation(RSR)
© 2017 Directed. All rights reserved.
Important!The devices, but supplied with the .Hood Pin and Remote Start Safety Override Switch are mandatory safety are 2NOT DBALL
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
Install Type with T-Harnessation 3 out
Page 11
[ ]1 Connection required only if Pit-Stop/Idle mode is desired.
HS CAN High: 3Tan/Black:
HS CAN Low: 4Tan:
(-) Ground: 14Black:
(+) 12 : 13V Input Red:
You can connect to either a 202XLRFTD a SmartStart module.OR
Refer to the SmartStart/ 202XLInstallation Notes for more information.
6: (-) HoodWhite/Black:
Hood Pin
Remote Start SafetyOverride Switch
Note: Hood pin onlyrequired on vehicle notequipped with a factoryhood pin.
(-) Parking Lights Output: 4Red/Black:
MainBodyECU1 72 83
6
9 21
22
25
10
13
23
26
11
14
29
24
27
12
15
18
20
19
4 16 28
30
1 8
169
HS CAN Low pin 14: ( ) V+ 12 pin 16:
HS CAN High pin 6:(-) Ground: pin 4
OBDIIDiagnostic Connector
10
14
12
10
RF
Prog utton. B
LED
4
14
12
2
DBALL2
Main Body ECU(white conn. on body ECU)
[ ] S :1 (-) Push-to- tartBlack Blue,or pin 7
ENGINESTARTSTOP
BlackConnector
1345
1214 11 10 8
2
9
6
13
7 Immo. Data 1: 10Yellow/Black:
Immo Data 2: 11Orange/Black:
[1] : 2(-) Push-to-Start Output Green/Black:
BRX: or pin 4Yellow Violet,
BTX: orBlue Green, pin 16
(-) Parking lights pin 30: or ,Yellow White/Black
Connexion required onlyif Pit-Stop / Idle mode isdesired. (Refer to QuickReference Guide ( )QRGat the end of the guide .)
Rev.: 20170825
Platform: DBALL2
Firmware: TL2 Remote Start Ready Installation(RSR)
© 2017 Directed. All rights reserved.
Vehicle Wiring Reference Chart - Type 3Page 12
Wire Information Connector Information
Function Color Pin Polarity Location Color Pins
Lexus CT 200h (Smart Key) 2011-2017
PTS Black 7 (-) Push-to-Start switch. Black 14
12V Red 16 (+) OBDII. White 16
HS CAN High Red 6 Data OBDII. White 16
HS CAN Low White 14 Data OBDII. White 16
Parking Lights Yellow 30 (-) Main Body ECU. Black 30
BRX Yellow 4 Data Main Body ECU. Black 30
BTX Blue 16 Data Main Body ECU. Black 30
Lexus HS 250h (Smart Key) 2010-2012
PTS Blue 7 (-) Push-to-Start switch. Black 14
12V Yellow 16 (+) OBDII. White 16
HS CAN High Green 6 Data OBDII. White 16
HS CAN Low Black 14 Data OBDII. White 16
Parking Lights White/Black 30 (-) Main Body ECU. Black 30
BRX Yellow 4 Data Main Body ECU. Black 30
BTX Blue 16 Data Main Body ECU. Black 30
Toyota Prius (Smart Key) 2010-2014
PTS Black 7 (-) Push-to-Start switch. Black 14
12V Red 16 (+) OBDII. White 16
HS CAN High Black 6 Data OBDII. White 16
HS CAN Low White 14 Data OBDII. White 16
Parking Lights Yellow 30 (-) Main Body ECU. White 30
BRX Violet 4 Data Main Body ECU. White 30
BTX Green 16 Data Main Body ECU. White 30
Toyota Prius V (Smart Key) 2012
PTS Black 7 (-) Push-to-Start switch. Black 14
12V Red 16 (+) OBDII. White 16
HS CAN High Black 6 Data OBDII. White 16
HS CAN Low White 14 Data OBDII. White 16
Parking Lights Yellow 30 (-) Main Body ECU. White 30
BRX Violet 4 Data Main Body ECU. White 30
BTX Green 16 Data Main Body ECU. White 30
Toyota Prius V (Smart Key) 2013-2016
PTS Black 7 (-) Push-to-Start switch. Black 14
12V Lt. Blue 16 (+) OBDII. White 16
HS CAN High Black 6 Data OBDII. White 16
HS CAN Low White 14 Data OBDII. White 16
Parking Lights Yellow 30 (-) Main Body ECU. White 30
BRX Violet 4 Data Main Body ECU. White 30
BTX Green 16 Data Main Body ECU. White 30
Rev.: 20170825
Platform: DBALL2
Firmware: TL2 Remote Start Ready Installation(RSR)
© 2017 Directed. All rights reserved.
Important!The devices, but supplied with the .Hood Pin and Remote Start Safety Override Switch are mandatory safety are 2NOT DBALL
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
Install Type 4ation
Page 13
[ ]1 Connection required only if Pit-Stop/Idle mode is desired.
HS CAN High: 3Tan/Black:
HS CAN Low: 4Tan:
(-) Ground: 14Black:
(+) 12 : 13V Input Red:
You can connect to either a 202XLRFTD a SmartStart module.OR
Refer to the SmartStart/ 202XLInstallation Notes for more information.
6: (-) HoodWhite/Black:
Hood Pin
Remote Start SafetyOverride Switch
Note: Hood pin onlyrequired on vehicle notequipped with a factoryhood pin.
(-) Parking Lights Output: 4Red/Black:
MainBodyECU1 72 83
6
9 21
2210
13
2311
14
29
24
27
12
15
18
20
19
4 16 28
30
10
14
12
10
RF
Prog utton. B
LED
4
14
12
2
DBALL2
Main Body ECU(white conn. on body ECU)
Immo. Data 1: 10Yellow/Black:
Immo Data 2: 11Orange/Black:
[1] : 2(-) Push-to-Start Output Green/Black:
BRX: 25pinViolet,
BTX: 2Green, pin 6
(-) Parking lights pin 30: ,Yellow
HS CAN Low: pin 2White,
HS CAN High: pin 3Black,
Steering Sensor
(White 5-pin connector)
5 1234
[1] ( S-) Push-to- tart:10White, pin
ENGINESTARTSTOP
Blackconnector 134
9 8 6
2
7
5
10
25
26
Main Body ECU(white conn. front
of body ECU)
(+) 12V pin 1: White,
Rev.: 20170825
Platform: DBALL2
Firmware: TL2 Remote Start Ready Installation(RSR)
© 2017 Directed. All rights reserved.
Vehicle Wiring Reference Chart 4- TypePage 14
Wire Information Connector Information
Function Color Pin Polarity Location Color Pins
Toyota Prius V (Smart Key) 2017
PTS White 5 (-) Push-to-Start switch. Black 10
12V White 1 (+) Main Body ECU. White 1
Parking Lights Yellow 30 (-) Main Body ECU. White 30
BRX Violet 25 Data Main Body ECU. White 30
BTX Green 26 Data Main Body ECU. White 30
HS CAN High Black 3 Data Steering Sensor on steering column White 5
HS CAN Low White 2 Data Steering Sensor on steering column White 5
Rev.: 20170825
Platform: DBALL2
Firmware: TL2 Remote Start Ready Installation(RSR)
© 2017 Directed. All rights reserved.
The 202 and antenna are not included and be purchased separately.optional XL MUST
Refer to the Passive Keyless Entry ( ) Installation Guide (N2102T) for detailed wiring information.PKE
4
4
XL202
An
ten
na
XOVER
SmartStart is and not included. It be purchased separately.optional MUST
SmartStart is and not included. It be purchased separately.optional MUST
Th solution offers three (3) configuration options to control your system 3x Locke Remote Start Ready ( ) :DBALL RSR OEMs This section provides specific installation information forRemote Start Activation, Kit or SmartStart (all sold separately).RF
SmartStart and 202.XL
Configuration Wires (Gray & White)Connect Gray wire to (-) Ground
5 pins
D2D (4 pins, white)
4 pins
2 pins,not usedCABLE
CABLE
The modules must be connected in a specific order. Refer to the section for more information.Module Programming
1. Use the D2D Crossover ( ) cable that is provided with 202, and the one in the package.XOVER XL NOT DBALL2. The modules must be connected in a specific order. Refer to the section for more information.Module Programming
The modules must be connected in a specific order. Refer to the section for more information.Module Programming
SmartStart/ 202 Installation NotesXL
SmartStart Revision B
RF Kit
RF PKE& CombinationKit
Refer to the Passive Keyless Entry ( ) Installation Guide (N2102T) for detailed wiring information.PKE
RF PKE BT, & SmartStart CombinationKit
SmartStart Revision A
LED
Prog.Button
D2D (4 pins, white)
4 pins
2 pins,not used
OR
SmartStart
Configuration Wires (White & Brown or Blue)Cut Brown or Blue Loop
LED
THIS SIDE UP
LED
DBALL/2DBALL
DBALL/2DBALL
DBALL/2DBALL
Page 15
Module Programming
Important
Page 71
10-pinD2D
XL202
10-pinD2DSmartStart
OR
The module be disconnected from any power source before SmartStart canDBALL mustbe connected to it. Failing to do so could damage .DBALL
a. To ensure that the D2D communication between SmartStart and works properly, theDBALLGray wire must be connected to a ground source ( SmartStart), and the Brown or BlueRev Bloop must be cut ( SmartStart).Rev A
b. Do connect the 2-pin harness (on SmartStart). Power and ground will be provided byNOTthe D2D connector.DBALL
Connect SmartStart to using the D2D port.DBALL
SmartStart Installation
Connect 202 to using the D2D port.XL DBALL
XL202 Installation
Refer to the Diagnostics section on page for more information and for troubleshooting purposes.LED 19-20
You have successfully completed the module programming sequence.
3 Press the Push-to-Start (PTS) button to turn vehicle ignition OFFonceonce the module is successfully programmed.
Off
ENGINESTARTSTOP
PUSH 2x
Solid Greenx3 secs.
Solid Red
& &
&ENGINESTARTSTOP
PUSH 1x
2
Press the vehicle Push-to-Start ( ) button (2) to turnPTS twicethe ignition . Wait for the to turn solid green forON LED ONthree (3) seconds .*
* The LED flashes orange if an OEM remote starter has beendetected. See the section "If the Vehicle
is Equipped with an OEM Remote Starter" on page 3.
110-pinD2D
1st
12-pin14-pin
2nd
3rd
&Solid
Connect the 10-pin 2-pin harnesses to, 1 and 14-pinDBALL, then w .ait until the turns solid redLED ON
Rev.: 20170825
Platform: DBALL2
Firmware: TL2 Remote Start Ready Installation(RSR)
© 2017 Directed. All rights reserved.
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check toensure everything is correct prior to moving onto the next step.
Note: Before connecting either the 202 or SmartStart module to , it is important to ensure that the proper feature andXL DBALLfunction programming is selected using Xpress (version 4. or higher). Visit www.directechs.com to download the latestVIP 5version of the application.
Warning! To take advantage of advanced features, you must use Xpress 4.5 (and higher) or the Directechs Mobile app.VIP
When the flashing operation is successful, you can proceed with the programming instructions below.
Flashing a module using your computer:
1. Connect the interface module to your computer using theXKLoader2.
2. Go to www.directechs.com using Internet Explorer, andselect the button.Config for RSR
3. Follow the instructions to select your vehicle, installationtype, and configure your options.
4. Once you have configured the firmware options, click on theFLASH button.
Flashing a module using your smartphone or tablet
1. Connect the interface module to your oader3.XKL
2. Launch the Directechs Mobile app on your smartphone ortablet.
3. Select and follow the on screenFLASH YOUR MODULEinstructions.
1If required for your installation, connect the 10-pin & 12-pinharnesses to the module Press hold the rogramming. and pbutton, then connect the 14-pin harness to the module.
10-pinD2D
1st
12-pin14-pin
2nd
4th
3rd
Warning gainst xecuting a Hard Reset!A EA hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (suchas and D2D options) may have to be reconfigured. See the section of this guide.RFTD Feature & Option List
2
Solid
&Release
3 Release the programming button. The turns solid red.LED ON
Module Reset
Hard Reset
2 & &
1
Wait 3 seconds until the orange then release theLED turns solidONp The turns solid red.rogramming button. LED ON
If required for your installation, connect the 10-pin & 12-pinharnesses to the module Press hold the rogramming. and pbutton, then connect the 14-pin harness to the module.
10-pinD2D
1st
12-pin14-pin
2nd
4th
3rd
A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashedto the module using the web config tool will not be affected.
Page 18
Solid Release Solid
Solid Flashes
&Wait 3 seconds until the orange aitLED turns solid , and w 10 more secondsONuntil the andLED starts to flash orange red.
Rev.: 20170825
Platform: DBALL2
Firmware: TL2 Remote Start Ready Installation(RSR)
© 2017 Directed. All rights reserved.
Rev.: 20170825
Platform: DBALL2
Firmware: TL2 Remote Start Ready Installation(RSR)
© 2017 Directed. All rights reserved.
Feature and Option List
Feat. Operation Flashes/Option Description
1. No RF Output* Module is connected to a remote starter using a standard installation.
2. RFTD Output Module is connected to an XL202 using an RSR or RXT installation (when available).
3. SmartStart Module is connected to SmartStart using an RSR or RXT installation (when available).
1. Driver priority* Unlocks only the driver door on first press and unlocks all doors on a second press within 5 seconds.
2. All Unlocks all doors on first press.
1. DisabledThe OEM alarm will not be controlled by DBALL upon remote start. No disarm or arm command will be
executed at the beginning or end of the sequence; it must be controlled by the Remote Starter.
2. SafelockSmart OEM Alarm Control will behave like a standard Safelock feature on a remote starter. It will unlock at
the beginning of the sequence, and relock after start and shutdown.
3. Enabled*
Smart OEM Alarm Control will synchronize with the OEM alarm so that it will disarm and rearm the vehicle
in the remote start sequence, only when required. The reason for this is, factory alarm control must often be
done by lock or unlock operation. This could create unnecessary actions on door lock modules, such as the
horn to honk. When possible, Smart OEM Alarm Control will monitor the alarm and door lock status to
detect if the disarm or rearm is required. If the vehicle is unlocked or is not equipped with factory alarm, the
disarm/rearm will not be executed. Smart OEM Alarm Control will also monitor the remote starter actions so
that the factory alarm control is not done twice. A remote starter, for which the Safelock feature is active,
will work perfectly with this option and will make it invisible to the user.
* Default Option
Smart OEM Alarm
Control3
RFTD Output Type1
Unlock Driver Priority2
It is recommended to configure all features and options listed below thethe using configuration tool found on the moduleflashing page on www.directechs.com. The web offers more options; however, manual configuration of the features is possibleusing the information on this page.
To enter feature programming routine� Turn t , thenhe ignition .ON OFF� Within 5 seconds, press and the rogramming button turns after 3 seconds . Release theHOLD LED ONp until the orange ( )
Programming button.� The to indicate the feature number is 1. After a short delay, the flashes rapidly to indicateLED LEDwill flash green once slowly red
the current option of feature 1 .(i.e. 1x green followed by 1x red indicates feature 1 is set to option 1) The flashing sequence willrepeat until .a new command is entered
Changing feature options� Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature. When installing
the in using 3x Lock Remote Start Activation only, there is no aftermarket transmitter on which to press lock/unlockDBALL RSR OEMto change the options of the selected feature. Tapping the green or blue lock/unlock wires on the black 10-pin harness to ground willchange the option for the selected feature.
� The flashes rapidly the number of times equal to the current option number. After a short delay, the flashes green slowlyLED LEDredthe number of times to indicate the current feature. repeat until .The flashing sequence will a new command is entered
Accessing another feature� Press and release the programming button a number of times to advance from the current feature to the next desired feature.� The flashes green slowly the number of times equal to the feature number. After a short delay, the flashes red rapidly toLED LED
indicate the current option of the current feature. repeat until .The flashing sequence will a new command is entered
When the maximum number of features or options is reached, the will start flashing again from the first feature or option.LED
Once a feature is programmed� Other features can be programmed.� The feature programming can be exited.
Exiting feature programming� No activity for 30 seconds; after 30 seconds, the will turn orange for 2 seconds to confirm the end of the programmingLED ON
sequence.OR
� Press and the programming button for 3 seconds. After 3 seconds, the will turn orange for 2 seconds to confirm theHOLD LED ONend of the programming sequence.
Feature ProgrammingProgramming
Button
Page 19
LED Diagnostics & TroubleshootingPage 20
Rev.: 20170825
Platform: DBALL2
Firmware: TL2 Remote Start Ready Installation(RSR)
© 2017 Directed. All rights reserved.
LED Description Troubleshooting
Module has no power.
Make sure the D2D harness is connected or that the 12
Volt is present between the red and black wires. If the
12 Volt is present, the module may be defective.
Waiting to begin the programming sequence.Ensure the correct programming procedure is being
followed.
Initialization failed.Reset the module and complete the programming again.
If the issue persists, please contact Technical Support.
Transponder functions were skipped.
(If compatible) when RXT mode is not desired or
convenience features are needed, please reset and
reprogram the module.
All required CAN networks has been detected. Normal operation.
1 of 2 CAN networks has been detected. Normal operation
Key2GO initiated.Please follow the steps indicated in “Module
programming” to complete the Key2GO programming.
Module was successfully programmed with all functions. Normal operation
Module was successfully programmed without
transponder functions.Normal operation.
CAN2 not detected.
Check the CAN2 Orange/Green and Orange/Brown wire
connections. Wake up the data bus by turning the
ignition on and try again. If your installation does not
require this connection, skip this step by pressing the
programming button 5 times.
J1850 not detected.Check the J1850 wire connection. Wake up the data bus
by turning the ignition on and try again.
CAN1 not detected.
Check the CAN1 Tan and Tan/Black wire connections.
Wake up the data bus by turning the ignition on and try
again. If your installation does not require this
connection, skip this step by pressing the programming
button 5 times.
Bypass data not detected.
Check the bypass line connection. If more than one wire
is used, make sure they are not inverted. Ensure the
vehicle still operates correctly using the factory key.
Bypass processing error.
The bypass calculation failed. Reset the module and try
again. If the condition persists, please contact Technical
Support.
ISO 1 not detected.
The Yellow/Black wire did not detect the expected
signal. Refer to "Installation (wiring diagrams & vehicle
wiring reference charts)" to check the connections.
ISO 2 not detected.
The Orange/Black wire did not detect the expected
signal. Refer to "Installation (wiring diagrams & vehicle
wiring reference charts)" to check the connections.
MUX not detected.
The Violet/Green or Violet/Brown wire did not detect the
expected voltage value. Refer to "Installation (wiring
diagrams & vehicle wiring reference charts)" to check
the connections.
Module Programming
Module Programming - Error Codes
Solid red
Flashes redx 1
Flashes redx 1
Flashes redx 2
Flashes redx 3
Flashes redx 4
Flashes redx 5
Flashes redx 6
Flashes redx 7
Solid greenx 3 secs
Flashesgreen
Solid orange
Flashes red& green
Off
Flashesorange
Flashesorangeslowly
Solid orangex 3 secs
Rev.: 20170825
Platform: DBALL2
Firmware: TL2 Remote Start Ready Installation(RSR)
© 2017 Directed. All rights reserved.
Page 21
LED Description Troubleshooting
OBDII feature is not supported.The diagnostic data bus was not detected, therefore the
SmartStart features will be limited.
Ground When Running (Status) command received. The module has initialized the remote start sequence.
Ignition ON command received.The module has received the Ignition ON command and
is processing the remote start sequence.
Start ON command received.The module has received the Start ON command and is
processing the remote start sequence.
PTS shutdown error.The PTS output from the module was not activated due
to safety protection.
CAN bus incorrectly detected.
Verify the CAN1 and CAN2 connections. Refer to
“Installation (wiring diagrams & vehicle wiring reference
charts)” to check the connections.
LOCK command received.
UNLOCK command received.
TRUNK command received.
AUX1 command received.
AUX2 command received.
AUX3 command received.
Takeover successful. Normal operation.
Runsafe was not disabled.No UNLOCK command was received prior to opening the
door, or the 45 second timer expired in takeover mode.
Brake was not detected.The brakes were not detected, which prevents the
system from shutting down the vehicle.
Smart key was not detected.The smart key was not detected, which prevents the
system from shutting down the vehicle.
Speed was detected.The vehicle was detected as moving, which prevents the
system from shutting it down.
3x OEM Lock Remote Start Activation was attempted
when RFTD feature is disabled.
Activated from Web automatically when using RSR flash
tool or can be done manually. Refer to feature
programing section for more information.
Feature error.An RSR feature file mismatch was detected. Please
contact Technical Support.
RSR codes
External module synchronization
Commands
Activation Ground When Running (Status)
If the bypass module fails to flash, it did not receive the
signal. Commands can come from RF or D2D.
Shutdown codes
(Flashes red,red thenorange) x 10
Flashes red& orange
Flashes redx 21
Flashes redx 2
Flashes redx 4
Flashes redx 7
Flashes redx 9
Flashes redx 10
Flashes redx 1
Flashes redx 3
Flashesgreen
Flashesgreenquickly
Flashesgreen x 1
Flashesorange x 1
Flashesorange x 2
Flashesorange x 3
Flashesorange x 5
Flashesorange x 4
Flashesorange x 6
Page 22
Flashes Diagnostic
1 Runtime expired.
2 Over-rev shutdown.
3 Low/No RPM.
4 Transmitter shutdown.
5 Brake shutdown.
6 Hood shutdown/Remote start safety override switch is ON*.
7 Remote start safety override switch is ON*.
The parking lights on your vehicle will flash a specific number of times 3 seconds following an unscheduled shutdown orfailure to start. Each flashing pattern is described below.
* If the vehicle hood status is supported through data, safety override switch input will report 7 flashes.
Parking Light Error Codes
Rev.: 20170825
Platform: DBALL2
Firmware: TL2 Remote Start Ready Installation(RSR)
© 2017 Directed. All rights reserved.
Limited Consumer WarrantyOne YearPage 23
For a period of from the date of purchase of a Directed Electronics remote start or security product, DirectedONE YEARElectronics. (“ ”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, theDIRECTEDsecurity or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or materialunder normal use, provided the following conditions are met: the Part was purchased from an authorized dealer;DIRECTEDand the Part is returned to , postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing theDIRECTEDfollowing information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and completeproduct and Part description.
This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to itsintended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation orother causes not arising out of defect in materials or construction.
TO THE MAXIMUM EXTENT ALLOWED BY LAW EXCEPT AS STATED ABOVE ALL WARRANTIES INCLUDING, , ,BUT NOT LIMITED TO EXPRESS WARRANTY IMPLIED WARRANTY WARRANTY OF MERCHANTABILITY, , ,FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUALPROPERTY ARE EXPRESSLY EXCLUDED AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY, ;PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY OBLIGATION OR LIABILITY IN CONNECTION WITH ITS,PRODUCTS DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALLACTS OF.THIRD PARTIES INCLUDING DEALERS OR INSTALLERS DIRECTED IS NOT OFFERING GUARANTEE OR. AINSURANCE AGAINST VANDALISM DAMAGE OR THEFT OF THE AUTOMOBILE ITS PARTS OR CONTENTS, , , ,AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER INCLUDING WITHOUT LIMITATION, ,LIABILITY FOR THEFT DAMAGE OR VANDALISM IN THE EVENT OF CLAIM OR DISPUTE INVOLVING, , . A ADIRECTED OR ITS SUBSIDIARY THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF,CALIFORNIA CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE.DISPUTE THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED.TO THE AUTHORIZED DIRECTED DEALER PURCHASE PRICE OF THE PART DIRECTED SHALL NOT BE’S .RESPONSIBLE FOR ANY DAMAGES WHATSOEVER INCLUDING BUT NOT LIMITED TO ANY CONSEQUENTIAL, ,DAMAGES INCIDENTAL DAMAGES DAMAGES FOR THE LOSS OF TIME LOSS OF EARNINGS COMMERCIAL, , , ,LOSS LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE NOTWITHSTANDING THE ABOVE THE, . ,MANUFACTURER DOES OFFER LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED OPTION THEA ’SPARTAS DESCRIBED ABOVE.
This warranty only covers Parts sold within the United States ofAmerica and Canada. Parts sold outside of the United States ofAmerica or Canada are sold “ - ” and shall have , express or implied. Some states do not allow limitationsAS IS NO WARRANTYon how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warrantygives you specific legal rights and you may also have other rights that vary from State to State. does not and hasDIRECTEDnot authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.For further details relating to warranty information of Directed products, please visit the support section of ’sDIRECTEDwebsite at: www.directed.com
920-10012-01 2013-07
This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the selectvehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. : Under noDISCLAIMERcircumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for anyconsequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, norwill they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / databus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of thisproduct be liable for consequential damages sustained in connection with this product and neither assumes nor authorizesany representative or other person to assume for it any obligation or liability other than the replacement of this product only.
Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1;7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent:2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089; EuropeanPatent: 1,053,128; Pat. Pending: 2,291,306. Made in Canada.
Rev.: 20170825
Platform: DBALL2
Firmware: TL2 Remote Start Ready Installation(RSR)
© 2017 Directed. All rights reserved.
Quick Reference GuideDBALL2 TL2- Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
1
2
3
Stop the vehicle in a safe parking spotand put the gear in Park (P).
Pressremote start
*button
* Your aftermarket remote may differ from the model shown in the illustrations.
Stop & put vehicle in Park (P)
P&
&
HO
LD
E vehicle withxitSmart Key
Pit Stop Mode
The Mode feature is practical when you need to stop and run an errand,Pit Stopbut wish to keep the engine running.
Note: We recommend that you always lock the doorsof your vehicle when leaving it unattended.
It is now safe to leave the exitengine running and thevehicle with the in hand.factory remote
Press the button to remote start the vehicle.*
The willparking lights flash once toindicate the vehicle is now in
it Stop .P Mode
Remote Start Ready ( )RSR
Remote Start Ready ( ) is a function that enables the interfaceRSRmodule to remote start the vehicle completely on its own.Consequently, there is no need for an aftermarket or an remoteOEMstarter in order to start the vehicle from a distance.
3x Lock Remote Start ActivationOEM
This solution includes the option to remote start your vehicle by pressing the Lockbutton 3 times consecutively. If your vehicle allows the remote to remainOEMactive while the engine is running, you may shut down your remote starter bypressing the Lock button 3 times once more.
Note: The range offered by remotes is limited and typically requires you to beOEMwithin eyesight of the vehicle to control it.
Vehicle Takeover
The vehicle takeover feature is not available in this firmware. The vehicle engine will shut down as soon as the door is opened.
Flashes x1
Quick Reference GuideDBALL2 TL2- Remote Start Ready (RSR) Installation
© 2017 Directed. All rights reserved.
Button(s) Actions
Press & hold for 1 second to lock.
Press & hold for 1 second to unlock.
Press & hold for 1 second to remote
start.
Press & hold for 5 seconds to activate
the trunk release (optional).
Press once, then to activate the
rear hatch/tail glass release (optional).*
Press 3 times, then to activate
the panic mode.
Press once, then to reset the
remote starter runtime.
List of Available Commands
x1 +
x3 +
x1 +
* This output is configurable. see your authorized installation center for moreinformation.
Note that the information below is for Viper, Clifford and Python models. Icons andcommands may differ depending on the remote brand and model purchased. Referto your authorized installation center for more information.
SmartStart Compatible
This system is compatible with Directed SmartStart 3.0. Fora complete list of supported features, please visitwww.mysmartstart.com.
What is SmartStart?
Now you can remote start, lock and unlock your car just by pushing a button onyour smartphone; using the SmartStart App from Directed, the leader in vehiclesecurity and remote start. The simple graphical interface gives you control over thefollowing features of your installed remote start or security with remote start system:
� Lock/Arm� Unlock/Disarm� Remote Car Starter� Trunk Release� Panic� Aux Channels
You can also control multiple vehicles – great for families – and assign more thanone user to control a vehicle. It's easy with SmartStart!
But, this is only the beginning! SmartStart is loaded with additional featuresincluding tracking, SmartSchedule, vehicle status, roadside assistance, homeGPScontrol, parked car finder and more.
3.0 enables a "Cloud-Connected Car" like never before, providing an entirely newlevel of 2-way interaction with your vehicle. Connectivity is managed through theDirected Cloud Services ( ) network linking car, app, end user, and the Internet.DCS
For more information, visit www.mysmartstart.com.