data sheet controlit - НовЭК, Новосибирская ... 1/16 din controller/alarm unit c50...

ControlIT

1/16 DIN Controller/Alarm Unit

C50

High visibility dual 4-digit display– shows set point and process variable

Standard relay or logic control output– simple time proportioning or on/off control

Optional alarm relay– additional relay to give hi/lo process alarm

Universal process input– direct connection for any process signal

IP65 (NEMA3) protection and full noiseimmunity– reliability in the harshest environments

NEMA 4X / IP66 construction–hose-down protection

One-shot autotune–automatic setting of optimum PID values

C50 – the 1/16 DIN controller to suityour simplest applications

Data SheetSS/C50_7

1/16 DIN Controller/Alarm UnitC50 SS/C50_7

2

C50

The C50 Controller/Alarm unit is a compact single loopcontroller, with the capability to measure, indicate andcontrol a variety of process variables.

The unit is ideal for simple PID control, offering On/Off orTime proportioning control with a one shot self-tune facility.The C50 can also act as an independent alarm unit, forexample, as an over-temperature safety cutout unit forfurnaces or ovens.

The unit is quickly set up for most process signal inputsand, with IP65 (NEMA3) front panel protection, is suitablefor a wide range of applications.

Solid State Relay

Contactor

AlarmAnnunciator

Standard Option

• Thermocouple• RTD• Linear milliamps• Linear volts, millivolts

• Relay• Logic

Relay

Universal Process Input Primary Output

Additional Alarm Output

KEY:


3

PID ControlThe unit’s primary relay or logic output can provide a time proportioning PID output,for control of contactors and solid state relays (SSR).

Override AlarmBy configuring the relay output as an overrange alarm, the C50 can act as anindependent alarm unit, providing protection for your process.

Ramping Set PointTo reduce shock to the process when changing set point, the C50 can be configuredto ramp up to the new set point over a preset period of time.

SP

t


4

Specification

Summary

PID single loop controller/alarm unit

Autotune Facility

Fully User Configurable

IP65 (NEMA3) Front Face

OperationDisplay

High intensity, 7-segment, 2 x 4 red LED display

Size upper 10mm (0.39 in.)

lower 8mm (0.31 in.)

Configuration

User defined via front panel and internal links.

OutputsPrimary output (fitted as standard)

User configurable as either:

Relay:

SPDT 2A 120/240V AC

or

TTL Logic (SSR Drive):

Digital >4.2V DC for

Min load 1kΩ

Not isolated from input

Output functions

User configurable as either:

On/Off control output

Time proportioning PID control output

PhysicalSize

48mm (1.89 in.) x 48mm (1.89 in.)x 110mm (4.33 in.) (depth behind panel)

Weight

<200g (0.44lbs.) approx.

OptionSecond relay output, configurable for alarms, meets thespecification of the standard relay output.

ElectricalVoltage:

90 to 264 V AC 50/60 Hz

Power consumption:

<4VA


5

Analog InputsSingle universal process input.

Type

Universally Configurable for:

Thermocouple (THC)

Resistance Thermometer (RTD)

Linear Millivolt

Linear Current

Linear DC voltage

Input Sampling Rate

1 sample/250ms

Input impedance:

Millivolts/THC/RTD >100MΩ

Volts >47KΩ

Current <4.7Ω

Linearizer functions

Automatic linearisation of THC types B, J, K, R, S, T, L, N andRTD Pt100

Broken Sensor protection

For the following options, break detected within two seconds andcontrol outputs DOWN scale to OFF (0% power):

THC, RTD, DC mV, DC Volts (1 – 5V and 2 – 10V),DC mA (4 to 20mA).

Cold junction compensation:

Automatic CJC incorporated as standard.

Input noise rejection

Common mode rejection: >120dB at 50/60Hz withbalanced lead.

Series mode rejection: >500% of span at 50/60Hz.

Accuracy

Measurement error: <± 0.25% of span ± 1LSD

Linearizer: Typically ±0.2 °C

Display range: –1999 to +9999

CJC accuracy: <± 0.05 °C /°C change in ambienttemperature

Temperature Limits

epyTCHT °C °F

485CEI&521SBNreP .niM .xaM .niM .xaM

RepyT 0 0561 23 2003

SepyT 0 9461 23 0003

JepyT

0 4.502 23 7.104

0 054 23 248

0 167 23 1041

TepyT002– 262 823– 305

0 6.062 23 105

KepyT002– 067 823– 9931

002– 3731 823– 3052

LepyT

0 7.502 23 2.204

0 054 23 148

0 267 23 3041

BepyT 001 2481 112 5133

NepyT0 9931 23 0552

0 008 0.23 1741

DTRepyT157CEI&06734NIDrep

9.001– 001 7.941– 9.112

002– 602 823– 204

9.001– 3.735 7.941– 999

0 9.001 23 6.312

0 003 23 175

0 008 0.23 1741

.etoN006wolebdeetnaraugtonsiycaruccaecnamrofreP ° 211(C ° SdnaR,Bsepytrof)F

.selpuocomreht

001,munitalperiw-3,DTR Ω 004ot0foegnarhtiw Ω.

Electrical Input Ranges

epyTtupnI.niMeulaV

eulaV.xaM.niMeulaV

eulaV.xaM

Vm 0 05 01 05

V 0 5 1 5

V 0 01 2 01

Am 0 02 4 02


6

Overall Dimensions

Electrical Connections

10(0.39)

110(4.33)

+ 0.6- 0

+ 0.03- 0

48(1.89)

48 (1.89)

Panel cut out45

(1.77 )

+ 0.6- 0

+ 0.03- 0

45

(1.77 )

N/O C N/C

7

8

9

16 17 18

13 14 15

10

11

12

1

2

3

4

5

6

Relay Output 2

L

N96 to 264V AC Mains Supply

N/O

C

N/C

Rel

ayO

utp

ut

1

RTD

–

+

THC

–

+

V/mV

+

–mA

+

–DC

fo

r S

SR

Dimensions in mm (in.)


7

Ordering Information

05C 1/ 61 tinUmralA/rellortnoCNID 05C X/ X X X X X X

)ylnoslaunamrof(egaugnaL

hsilgnEhcnerFnamreG

KFD

sepyTtupnI

lasrevinU 2

1tuptuO

cigoL/yaleR 1

2tuptuO

enoNyaleR1

01

serutaeFlaicepS/gnimmargorP

enoN 0 0 0


SS

/C50

Issu

e 7

ABB Inc.125 E. County Line RoadWarminsterPA 18974USATel: +1 215 674 6000Fax: +1 215 674 7183

ABB LimitedHoward Road, St NeotsCambridgeshirePE19 8EUUKTel: +44 (0)1480 475321Fax: +44 (0)1480 217948

ABB has Sales & Customer Supportexpertise in over 100 countries worldwide

www.abb.com

The Company’s policy is one of continuous productimprovement and the right is reserved to modify the

information contained herein without notice.

Printed in UK (07.04)

© ABB 2004

ControlIT

1/8 DIN Process Controller

C100

PID controller with 'one shot' auto-tune– single loop, heat/cool and ramp/soak as standard

Quick code, front face or PC configuration– easy commissioning and operation using our

Windows™-based software

Universal process input withtransmitter power supply– direct connection for any process signal

Hoseproof front panel and full noise immunity– reliability in the harshest environments

RS485/Modbus serial communications– SCADA, PLC and open systems integration

C100 –the easy-to use 1/8 DIN controller

with extensive capabilities

Data SheetSS/C100_10

1/8 DIN Process ControllerC100 SS/C100_10

2

C100

The C100 Universal Process controller is a highly versatile,single loop controller designed to be exceptionally easy tooperate and set up.

Universal input and integral transmitter power supply ensurethat the C100 has the capabilities to measure a wide rangeof process signals such as temperature, pressure, flow andlevel.

Analog, logic and relay control outputs are all fitted asstandard, with the option to add further i/o capabilities suchas additional relays, remote set point and digital input, tosuit your application.

The configuration of the C100 is simply achieved by movingthe security switch and entering a simple code from thefront panel keys. No passwords, no input links, nocomplications.

With hoseproof front panel protection and superior RFimmunity as standard the C100 has been designed tocontrol reliably in the harshest of today’s industrialenvironments.


3

PID Control

Alarms

PVRetransmission

AlarmAnnunciator

SCADA Systems (on PC)KEY: Standard Option

Transmitter PowerSupply

Universal Process Input• Thermocouple• RTD• 4 to 20mA• Volts, millivolts

Primary Outputs1 x Analog1 x Logic1 x Relay

Serial CommunicationsRS485 Modbus RTU

Additional Alarm Outputs2 x Relays

Auxiliary Inputs

• Digital• Remote Set Point


4

PID ControlSimple PID control is available using any of the unit’s threebuilt-in outputs.

• 4 to 20mA analog

• Logic 18V time proportioning (to drive solid state relays)

• 5A relay for Time proportioning or On/Off control

SP

t

SP

PV1

PV2 OP

MRA A

OPOP

MRA A

OPOP

SP

Ramp/Soak Set Point ProfilesThe ramp/soak facility available on every C100 provides for asingle program, four-segment profile. This facility also includesguaranteed ramp/soak, repeat program, skip and reset.

Master/Slave and CascadeTwo or more C100s can be used in master/slave, or cascade,configuration with the addition of the remote set point optionto the basic unit.

Heat/CoolHeat/Cool control strategies may be implemented on thestandard C100, using a combination of the analog, logic andrelay outputs.

RS485/ModbusFitted with an optional RS485 serial communication board, theC100 can communicate with PLCs and SCADA systems using


5

Standard FunctionsControl types

Programmable for manual, on/off, time proportioning,current proportioning and heat/cool control.

Set points

Local

Remote

4 selectable fixed value

Ramping set point

Profile controller

Number 4 ramp/soak segments

Features Guaranteed ramp/soak, self seeking set point,program repeat

Controls Run, hold and stop from front panel switcheRun/hold or run/stop from digital input

Alarms

Number Two user-defined

Type High/low processHigh/low deviation

Specification

SummaryP, PI, PID single loop controller

Autotune facility

Fully user configurable

Hoseproof front face

OperationDisplay

High-intensity 7-segment, 2 x 4-digit LED display

Display range –999 to +9999

Display resolution ±1 digit

Display height 10mm (0.39 in.)

Configuration

User defined via front panel or PC Configurator


6

Analog InputsNumber

One as standard

One optional (4 to 20mA remote set point input)

Input sampling rate

250ms per channel

Type

Universally configurable to provide (Channel 1 only):

Thermocouple (THC)

Resistance Thermometer (RTD)

Millivolt

Current

DC voltage

Input impedance

mA 100Ω

mV, V >10MΩ


Programmable for standard inputs:

SqRoot, THC types B, E, J, K, N, R, S, T or Pt100

Broken sensor protection

Upscale drive on THC and RTD

Downscale drive on milliamps and voltage

Cold junction compensation

Automatic CJC incorporated as standard

Stability <0.05°C/°C change in ambient temperature

Input protection

Common mode isolation >120dB at 50/60Hz with 300Ωimbalance

Series mode rejection >60dB 50/60Hz

Transmitter power supply

24V, 30mA max. powers one 2-wire transmitter

...Specification


7

elpuocomrehT egnaRmumixaM °C egnaRmumixaM °F )gnidaerfo%(ycaruccA

B 0081ot81– 0723ot0 ro%52.0 ±2° 002evoba(C ° )C

E 009ot001– 0561ot041– ro%52.0 ± 5.0 °CJ 009ot001– 0561ot041– ro%52.0 ± 5.0 °CK 0031ot001– 0532ot041– ro%52.0 ± 5.0 °CN 0031ot002– 0532ot523– ro%52.0 ± 5.0 °CR 0071ot81– 0003ot0 ro%52.0 ± 0.1 ° 003evoba(C ° )C

S 0071ot81– 0003ot0 ro%52.0 ± 5.0 ° 002evoba(C ° )C

T 003ot052– 055ot004– ro%52.0 ± 5.0 °C

DTR egnaRmumixaM °C egnaRmumixaM °F )gnidaerfo%(ycaruccA

001TP 006ot002– 0011ot523– ro%52.0 ± 5.0 °C

stupnIraeniL egnaR )gnidaerfo%(ycaruccA

spmailliM 02ot0 ro%52.0 ±2µA


stloV 5ot0 ro%52.0 ± 002 µV

stloV 5ot1 ro%52.0 ± 002 µV

stlovilliM 05ot0 ro%52.0 ± 02 µV

tupnItooRerauqS egnaR )gnidaerfo%(ycaruccA


.setoN.segnartoor.qsdnaelpuocomrehtfodnewolemertxetadeetnaraugtonsiycaruccaecnamrofreP

001,munitalperiw-3,DTR Ω 004ot0foegnarhtiw,)157CEI(dradnats06734NIDrep Ω.orezwolebnaps.niM

sdradnatsCHTsdradnatsDTR

07TepyT ° 621/C °F501NepyT ° 981/C °F

485CEI01734NID157CEI06734NID

Standard Analog Input Ranges


8

...Specification

OutputsControl output/retransmission

Analog, configurable in the range of 4 to 20mA

Max. load 15V (750Ω at 20mA)

Accuracy ≤0.25% of span

Dielectric 500V DC from I/P (not isolated from logic O/P)

Logic output

18V DC at 20mA

Min. load 400Ω

Dielectric 500V DC from I/P (not isolated from control O/P)

Relay output

One relay as standard (SPDT) (5A @ 115/230V AC)

OptionsOne option board can be installed from:

Type 1 One relay

Type 2 Two relays + one digital input + remote setpoint

Type 3 One relay + one digital input + remote setpoint + Modbus serial communications

Relay output

SPDT 5A @ 115/230V AC

Digital input

Type Volt-free

Minimum pulse 250ms(not isolated form remote set point)

Modbus serial communications

Connections RS422/485, 2 or 4-wire

Speed 2.4k or 9.6k baud rate

Protocol Modbus RTU slave

Remote Set Point Input

4 to 20 mA DC, 100Ω nominal input impedance

Preset to process variable engineering units(not isolated from digital inputs)

PhysicalSize

48 wide x 96 high x 125mm(1.89 in. wide x 3.78 in. high x 4.92 in.)

Weight

250g (0.5lb) approximate

ElectricalVoltage

85 to 265V AC (50/60Hz)

24V DC

Power consumption

< 6VA

EnvironmentalOperating limits

0 to 55°C (32 to 131°F)

5 to 95%RH non-condensing

Temperature stability

< 0.02% of reading or 2µV/°C (1µV/°F)

Front face

IP65 (NEMA3), case rear IP20

EMCEmissions

Meets requirements of EN50081-2

Immunity


Design and manufacturing standards

CE Mark

Safety standards

EN61010 – 1

C22.2 No. 1010

UL 310 – 1

FM 3810


9

COMMANDER 100

119 (4.64) 48 (1.89)

96(3.78)

14.7 (0.58)

91(3.58)

Cut out dims. 45 wide x 92 high

(1.77 wide x 3.62 high)

+ 0.6– 0

+ 0.8– 0

+ 0.02– 0

+ 0.03– 0

2.7 (0.11) 44.6 (1.76)

40 (1.57) 79 (3.11)

Dimensions

Dimensions in mm (in,)


10


Remote Set Point Input (–)

Remote Set Point Input (+)

Digital Input (–)

Digital Input (+)

Relay 2 Normally Open

Relay 2 Common

Relay 2 Normally Closed

Analog Input (–)

Analog Input (+)

Analog Input (Rtd)

Transmitter PSU (+)

Logic / Analog Output (+)

Analog Output (–)

Logic Output (–)


Relay 1 Common


Neutral

Live

1

2

3

4

Thermocouple,

Millivolts and Volts

(–)

(+)

2-Lead RTD

and Resistance

1

2

3

4

Milliamps

(100 shunt placed across

Terminals 1 and 2)

(–)

(+)

Milliamps using internal

2-wire transmitter power supply

(100Ω shunt placed across

Terminals 1 and 2)

13

14

15

16

17

18

19

20

21

22

23

24

1

2

3

4

5

6

7

8

9

10

11

12

Seebelow

1

2

3

4

3-Lead RTD

RedRed

White

a.c. power


Relay 3 Common


1

2

3

5

Tx

–

+4

1

2

3

4

White

Red

+

–

+

–

Common

20

21

22

23

24

Tx

Tx/ Rx RS485


11

Instrument Coding ExampleC100 / 01 0 0/ STD

C100 1/8 DIN Process Controller

One additional relay

85V to 265V AC power supply

Standard build

Configured to factory standard

Ordering Guide

001C 1/8 rellortnoCssecorPNID 001C / X X X X / X X X X

draoBnoitpO enoN–yalerlanoitiddaenO–

tupnilatigideno+syalerlanoitiddaowT–Am02ot4tnioptesetomer+

tupnilatigideno+yalerlanoitiddaenO–subdoM/584SR+tnioptesetomer+

000

0

012

3

ylppuSrewoP CAV562otV58CDV42

01

dliuB dradnatSynapmoClavorppaASC

lavorppaLUlavorppaMF

0124

serutaeFlaicepS/gnimmagorP dradnatsyrotcafotderugifnoCstnemeriuqerremotsucotderugifnoC

serutaeflaicepS

SCS

TUP

DSX X



ABB LimitedHoward Road, St. NeotsCambridgeshirePE19 8EUUKTel: +44 (0)1480 475321Fax: +44 (0)1480 217948


www.abb.com




© ABB 2004

SS

/C10

0Is

sue

10

Wall-/Pipe-mount Universal Process Controller

COMMANDER 310

IP66/NEMA 4X wall/pipe-mount housing– no need for an instrument panel

Single output, Heat/Cool or Motorized Valvecontrol– one controller for every PID control application

9 program, 30 segment Ramp/Soak– comprehensive set point profiling capabilities

Analog, relay and logic outputs as standard– extensive control output requirements

built-in

Universal process input with 0.1% accuracy– direct connection of any process signal, simple

installation without recalibration

RS485 Modbus serial communications– SCADA, PLC and open systems integration

COMMANDER 310 – gives you thecontrol that you need wherever

you need it

Data SheetSS/C310_6

Wall-/Pipe-mount Universal Process ControllerCOMMANDER 310 SS/C310_6

2

COMMANDER 310

The COMMANDER 310 Wall/pipe-mount UniversalProcess Controller is a highly versatile single-loop controllerpackaged in a robust field-mounting housing.

No need to fit an expensive instrument panel when installingor upgrading process equipment. The COMMANDER 310can be rapidly commissioned by simply fixing it to any flatsurface or pipe and making the electrical connections viathe cable entry glands on the underside of the unit.

The instrument has extensive control and i/o capabilitiesfitted as standard, allowing it to be rapidly configured foralmost any application.

With IP66/NEMA4X water/dust protection theCOMMANDER 310 can be mounted right next to yourprocess, no matter how harsh the environment.

Valve positioner

Solid state relay

Contactor

Alarmannunciator

Chart recorderSlave controller

SCADA systems (on PC)KEY: Standard Option

Transmitter PowerSupply

Auxiliary Inputs

• Digital (x 2)• Remote Set Point• Valve position feedback

Universal Process Input• Thermocouple• RTD• 4 to 20mA• Volts, millivolts

Control Outputs• Analog (4 to 20mA)• Logic• Relay x 2

Additional Alarm Outputs1 x Relay

Auxiliary OutputProcess ValueRetransmission

Serial CommunicationsRS485 Modbus RTU


3

PID ControlThe COMMANDER 310’s isolated analog output provides thestandard control output to I/P converters, thyristors etc.Alternatively, built-in relays can be used to generate a time-proportioning control output.

Solid State Relay SSRA 12V time-proportioning logic output on the standard C310 canbe used to drive solid state relays (SSRs).

SP

t

Valve PositionThe COMMANDER 310 is fitted with twin relays and a valve-position input for closed-loop control of a motorized valve.'Boundless' control (without position feedback) and analogcontrol (using 4 to 20mA output) are also available in thestandard unit.

Heat/CoolHeat/cool control strategies may be implemented on thestandard COMMANDER 310, using a combination of theanalog control output and one relay.

Ramp/Soak Set Point ProfilesThe standard ramp/soak facility provides 30 segments, freelyassignable amongst 9 programs. A Segment Event functionenables relays to be switched on or off at predetermined pointswithin the program.

Serial CommunicationsNot only does the COMMANDER 310 provide clear processinformation in the field, it can also communicate plant data tocontrol rooms via an RS485 link, using Modbus protocol.


4

Specification

Summary

epytDTR/CHT&521SBNreP

485CEI

C F

.nim .xam.nimnaps

.nim .xam.nimnaps

BepyT 81– 0081 017 0 2723 8721

EepyT 001– 009 54 841– 2561 18

JepyT 001– 009 05 841– 2561 09

KepyT 001– 0031 56 841– 2732 711

LepyT 001– 009 05 841– 2561 09

NepyT 002– 0031 09 823– 2732 261

S&RepyT 81– 0071 023 0 2903 675

TepyT 052– 003 06 814 275 801

06734NIDrepDTR157CEI& 002– 006 52 823– 2111 54

.setoN

004wolebdeetnaraugtonsiycaruccaecnamrofreP 257(C rof)FselpuocomrehtSdnaR,Bsepyt

001,munitalperiw-3,DTR 004ot0foegnarhtiw, orezwolebnaps.niM 07TepyT 621(C )F

501NepyT 981(C )F

epyttupnI eulav.niM eulav.xaM naps.niM

stlovilliM 0002– 0002 5.2

stloV 02– 02 52.0

spmailliM 001– 001 52.0

ecnatsiseR 0 0008 01

Temperature limits

Electrical limits

Input noise rejection

Common mode rejection >140dB at 50/60Hz with 500imbalance

Series mode rejection >60dB at 50/60Hz

Accuracy

Measurement error <0.1% of reading or 5V

Linearizer Typically 0.1C (0.2F)

Display range –9999 to +9999

CJC accuracy <0.05C/C change in ambient

Transmitter power supply

24V 30mA max. powers one loop, fitted as standard

COMMANDER 310 Wall-/Pipe-mount Universal Controller

P, PI, PID single loop controller

Autotune facility

Fully user configurable

IP66 (NEMA 4X) front face and housing

OperationDisplay

High-intensity 7-segment, 0.56 in. (14mm), 2 x 6 red LED display

Configuration

User defined via front panel

Analog InputsNumber

Three universal process inputs

Type

Universally configurable for:

Channels 1 & 2 – Thermocouple (THC)

(Process Variable & Resistance thermometer

Remote Set Point) (RTD)

Millivolt

Current

DC voltage

Resistance

Channel 3 – DC voltage

(Actuator PositionFeedback) Current Resistance

Input sampling rate

160ms per channel

Millivolts/THC >10M

Voltage 500k

Current 10


Programmable for input channels 1 and 2

Sqrt, X3/2, X5/2 THC types B, E, J, K, R, S, T, L, N or Pt100

Broken sensor protection

Programmable Up/Downscale or None

Cold junction compensation

Automatic CJC incorporated as standard


5

OutputsControl output

Configurable as either:

Analog in the range of 0 to 20mA

Max. load 15V (750 at 20mA)

Accuracy 0.1% of span

Isolation 1kV AC

Logic 12V DC (SSR drive)

Max. load 400

Isolation 1kV AC

Retransmission

0 to 20mA configurable for process variable, set point or positionfeedback values

Max. load 15V (750 at 20mA)

Accuracy 0.1% of span

Relay outputs

Three relays, configurable for time proportioning control, valvedrive or alarms.

SPDT 5A 120/240V AC normally open or normally closed

OptionSerial communications

Connections – RS485, 4-wire, 1.2k to 9.6k baud rate

Protocol – Modbus RTU

ElectricalVoltage

115V 15% or 230V 15% 50/60Hz (link selectable)

Power consumption

<10VA

Power interruption protection

<60ms/<3 cycles, no effect

>60ms/>3 cycles, controlled reset

Line interference

Meets IEC 801 Pt IV level 3 (>2kV spikes)

EnvironmentalOperating limits

–10 to 55C (14 to 131F), 0 to 95%RH non-condensing

Temperature stability

<0.02% of reading or 1V/C (0.5V/F)

Housing dust/water protection

IP66 (NEMA 4X)

RF protection

Meets IEC 801 Pt. III level 3

EMCEmissions


Immunity


Design and Manufacturing Standards

CE

CSA

CSA/FM Class 1 Div.2 Hazardous Area


6

Dimensions


Weight 4.5lb (2kg)

2.68 (68)

8.43(214)

9.13(232)

Fixi

ng C

entr

es

2.68 (68)

8.43(214)

9.13(232)

Fixi

ng C

entr

es

1.65(42)

2.375 (61) O.D.Vertical or Horizontal Post(Mounting Kit Pt. No. 4600/0138)

Allowance forCable Bends

6.3 (160)

9.84(250)

2.72 (69)FixingCentres

7.9 (200)

3 Fixing Holes0.25 (6.5) Dia

PowerSupply

Relay 1

Relay 2

Relay 3 Process Variable InputRemote SetPoint Input

Tx– 0V Rx+ Rx– + – + – 3rd 3+ 3– 1 2 CTx+

Modbus (RTU)(if option fitted)

LogicInput

ControlOutput

Position FeedbackInput

Retransmission Output

N/O C N/C N/O C N/C N/O C N/C 3rd 1+ 1– 3rd 2+ 2–

18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

12 13 14 15

1 2

16 17

L N

3 4 5 6 7 8 9 10 11

Dimensions in ins. (mm)


7

Ordering Information

rellortnoCssecorPlasrevinUtnuom-epiP/-llaW013REDNAMMOC X/013C X X /X XXXX

draoBnoitpOenoN

snoitacinummoCsubdoM584SR00

01

ylppuSrewoP)sgulpgniknalbhtiwdettifTPN(CAV511

)sdnalgelbachtiwdettif02M(CAV032)sdnalgelbachtiwdettif02M(CAV511

)sgulpgniknalbhtiwdettifTPN(CAV032

1245

dliuB

dradnatS)gnidnep(devorppaASC

2.viD1.lCMF/ASC

013

serutaeFlaicepS/gnimmargorP

dradnatsyrotcafotderugifnoCliatedremotsucotderugifnoC

serutaeflaicepsdeergA

DTSSUCXXPS

Instrument Coding Example C310 / 01 1 1 / STD

COMMANDER 310 Controller

RS485 Modbus Communications

115V AC

CSA approved

Factory standard configuration


SS

/C31

0Is

sue

6


ABB LimitedHoward Road, St NeotsCambridgeshirePE19 8EUUKTel: +44 (0)1480 475321Fax: +44 (0)1480 217948


www.abb.com




© ABB 2004

data sheet controlit - НовЭК, Новосибирская ... 1/16 din controller/alarm unit c50...

Documents