crush light curtain static - waupaca elevator company
TRANSCRIPT
PTE10124-H
29 JULY 2020
WE1726 North Ballard Road, Suite 1 - Appleton, WI 54911 - 920.991.9082
Technical Support 855.804.5774 - [email protected]
10. Depending on layout, place either transmitter or receiver in place against the trim and fasten with the provided hardware. The sticker and adjustments must be mounted facing outward.
6. Mark every transmitter and receiver fastening holes.
7. Place the transmitter and receiver off to the side.
8. Drill (2) - 1/4” through holes on the wall and pocket at the locations previously marked for the cords to be fed through the wall(s)/pocket.
9. Pilot (12) - 1/16” x 5/8” deep holes at all transmitter and receiver fastening holes.
Transmitter
Receiver
Wall
Inside the Wall Pocket
LightArray
Screen
1. Locate both car entrance walls. For example, locate wall pocket C and wall E. Reference Frameless Car Assembly.
2. Locate the top of the car sill and measure up 73-1/4” on the inside the wall and the pocket. Make a light mark.
3. From the previously made line. Measure 1/4” from the light curtain trim face on the wall and the pocket. Make a light mark.
4. Measure and lightly make a mark or shim 1/4” above the car sill and place the transmitter and receiver against the trim on wall C and E.
5. Verify the marks are placed correctly for the cord to be fed through the walls discreetly with the light array screens facing each other. The sticker and adjustments must be mounted facing outward.
CRUSHHAZARD
CUTTING
HAZARDCRUSHHAZARD
CRUSH
HAZARD
CRUSHHAZARD
CRUSH
HAZARD
ELECTRIC
HAZARD
FALLING
HAZARD
CRUSHHAZARD
PINCH
HAZARD
PUNCTURE
HAZARD
ANTI-STATIC
ALERT
This is not a gate substitute, both the gate and light curtain must be installed.
Instructions are only for products supplied by Waupaca Elevator.
1
10.
8
Fluorescent lights and direct sun light may aff ect operation of light curtain.
LightCurtian
Trim
Car Sill
1/4” hole
1/4” from the trim to hole
73 - 1/4”
LIGHT CURTAIN
INSTALLATION(IF PROVIDED)
Verify that both light array screens are facing each other and are aligned ready to transmit and receive light signals. Verify the relationship for both the receiver and transmitter are parallel on
the top and bottom surfaces. If the receiver and transmitter are not properly aligned the light curtain may not function properly.
2.
3.
9.
8.
1.
3
2
9, 10
SERIES : 008 ,114 , 115 ,116 , 118 , 021, 022 , 210
PTE10124-H
29 JULY 2020
WE1726 North Ballard Road, Suite 1 - Appleton, WI 54911 - 920.991.9082
Technical Support 855.804.5774 - [email protected]
CRUSHHAZARD
CUTTING
HAZARDCRUSHHAZARD
CRUSH
HAZARD
CRUSHHAZARD
CRUSH
HAZARD
ELECTRIC
HAZARD
FALLING
HAZARD
CRUSHHAZARD
PINCH
HAZARD
PUNCTURE
HAZARD
ANTI-STATIC
ALERT
LIGHT CURTAIN INSTALLATION
(IF PROVIDED) SERIES : 008 ,114 , 115 ,116 , 118 , 021, 022 , 210
ATTENTION : Once the elevator installation is complete, verify light curtain functions properly. When the elevator is traveling and an obstruction is placed between the transmitter and receiver the elevator must stop. Reference Light Curtain
Manufactures Instructions for adjustments and/or troubleshooting.
Instructions are for only products supplied by Waupaca Elevator.
11. Make a note of wire location in light curtain plugs (label if necessary) and remove the connector. Feed wire through 1/4” holes in the cab, and rewire plug with previous noted wire locations.
12. Locate light curtain interface appropriately and fasten onto car top with proper hardware. Plug in transmitter and receiver into light curtain interface. Do not pierce through to the interior surface of the car.
Note: Verify voltage is set to 115V, switch 1 is “ON”, and switches 2 & 3 are “OFF”.
13. Populate the gate switch receptacles sequentially GATE1 through GATE2 on the car top board. The light cur-tain can ONLY be plugged into GATE3. Reference Manual Switch Gate Program Page and verify that no fl oor has GATE3 programed.
14. Remove the jumper from GATE3 and insert into the female connector on the curtain interface harness. Then, insert the male plug into GATE3 on car top board.
15. Unplug the light curtain adapter from the remaining light curtain interface whip and feed the harness through a knock out on the car top. Reconnect the light curtain adapter to light curtain interface whip and plug into car top circuit board labeled AG1 - AG3. Verify secure connection of all the wires.
16. Secure all connections, wires, and conduit to car top as necessary. All wiring must meet N.E.C. and local code requirements.
Brown
Black
Top of Light Curtain Plug
Blue
Light Curtain Interface
Auto Gate Plugs
Plug into GATE3
Insert Jumper plug from
GATE3
Light Curtain Adapter
Note: If there is more
than 1 set of light curtains,
make sure they are wired
in a series circuit.
13.
15.
14.
12.
11.
15
14
12
11
13, 14