core review 2012-2013 04

Core Review2012-2013 04

If you are going to step off a ladder onto a platform or roof, the top of the ladder should extend at least__feet above the point where the ladder touches the platform or roof.4325

The color of the oxygen hose is__WhiteYellowRedGreen

There are ____ categories of on-the-job events.ThreeTwo FourFive

A red barricade in a work area indicates danger from ___Radiation in the airFalling objects or a load of suspended over an areaPhysical hazards such as bumping into equipmentLoose debris on the ground

Flash burns can cause serious eye damage. Never wear___when welding. A watchJewelryContact lensesglasses

The ultimate responsibility for on-the-job safety rests with___Your supervisorOSHAYouHuman resources

Most hard hats are now made of ___.Metal FiberglassTeflonvinyl

A type of IA ladder is rated for___ use

300 lbs., extra duty /professional225 lbs., medium duty/ commercial200 lbs., light duty/ household250 lbs., heavy duty / industrial

Work that takes place near a hazard but not in direct contact with it is called __ work.Proximity Near contactExtra cautionHazardous

To prevent ear infections ,clean your ear plugs regularly with__.AlcoholSoap and waterMineral spiritsSoft cloth

The lanyard on a safety harness must be short enough to prevent you from falling more than __.9678

Because heating and cutting metals can create more than ___ , always perform cutting operations in a well- ventilated area.Galvanized brassToxic fumesSlagOxyfuel

Yellow signs with a black panel with yellow letters are __ signs. CautionInformationalSafetyDanger

Every electrical cord should have a __ label attached to it.VoltageULWattage Gfci

To protect against a brief exposure from gas or fumes, use ___.Supplied air maskHalf mask, or mouth piece with mechanical filterFull face piece with chemical canisterSelf-contained breathing apparatus

Someone who has the knowledge and experience to handle problems is a ___ person. CompetentEligible ProficientQualified

The highest safe standing level on a extension ladder is the ___ rung from the top.Fourth Fifth SecondThird

You must check three things before and during welding operations : hoses, regulators, and ___.NozzlesRespiratorsThe wind directionThe work area

In welding, the ___ containing oxygen and acetelyne must be stored upright and separated by metal NozzlesProtective capsRespiratorsCylinders

Heat is anything that will raise the fuels temperatures to the __ point.Vapor BurnArcflash

Poor housekeeping, excessive noise , and inadequate guards are ___.Justifiable conditionsUnsafe conditionsUnsafe actsAcceptable risks

If an electrical current cannot complete its circuit, it will try to go to ___.

WaterGroundAirMetal

Always use a friction striker to light a ___.Cutting torch Galvanized surfaceFlame-cutting outfitFlame cutter

One of the most common safety grounding systems used to protect you from accidental electrical shock is the __ system.Five-wireFour-wireTwo-wireThree-wire

A ___ / tagout system protects workers from hazardous energy while they work with machines and equipment

DisconnectLockoutDe-energizedlockdown

You must never___ your personal protective equipment.MaintainClean or buffInspectAlter or modify

Post and chain, steel cable, and ___ are acceptable for a protective barricade.RopeWooden railsYellow tapePlastic barrels

Every shipment of a hazardous substance must be accompanied by a(n), which must be made available on the job site.PPE ANSISCBAMSDS

Never remove the tags from a fire extinguisher. These tags show ___The manufacturer of the extinguisherWho maintains the fire extinguisherWhen the fire extinguisher was purchasedWhen the fire extinguisher was last serviced and inspected.

Never remove the tags from a fire extinguisher. These tags show ___The manufacturer of the fire extinguisherWho maintains the fire extinguisherWhen the fire extinguisher was purchasedWhen the fire extinguisher was last serviced and inspected.

One basic job site electrical safety guideline is to use only a ___ for plugs.GFCISpliceSwitchConcealed receptacle

Effective speech is even more important with telephone calls because There may be background noiseYou cannnot see the person or their reactionsYour teammates may be listening The person may not hear you clearly

Effective speech is even more important with telephone calls because There may be background noiseYou cannot see the person or their reactionsYour teammates may be listening The person may not hear you clearly

More words automatically mean better writingTruefalse

Instructions or steps for procedures are easier to remember if you ___.Memorize each stepImagine yourself performing the taskRead the text out loudWatch someone do it after you read the text

One of the best ways to improve your speaking skills is to ___.Take many notes Tell jokes constantlyListen to someone who speaks wellListen to everyone around you

An appendix is a(n) ___.Alphabetical listing of terms and definitions used in a bookAlphabetical listing of topics with corresponding page numbersGraphic summary of important facts an figuresSource of additional information placed at the end of a section, chapter, or book

Verbal communication is the skill of ___.Thinking and comprehendingBeing on timeSpeaking and listeningFilling out reports

When making a telephone call, you should first___.Identify yourself Ask to whom you are speakingTake notes of the conversationExplain the purpose of your call

A punch list___.Identifies deficiencies requiring correction at a completionIncludes the definitions of words from a bookProvides and alphabetical listing of site materials Provides a summary of the project

One way to highlight information in a paragraph is to put it in a(n)___.Bulleted listGlossaryAppendixindex

Real listening is the process of ___ what someone has said not just hearing it.RecordingRepeating Summarizingunderstanding

Identifying options and alternatives is an important part of ____.Critical thinking skillsDeveloping an organizational chartDeveloping a financial planStarting a business

Another term for PDA is a ___ computerLaptopHandheldPortabledesktop

When offering constructive criticism to a team mate, you should never___.Criticize him or her in front of teammates or the supervisorPoint out incorrect techniques the first time they occurWrite down your criticismsCompliment him or her first

The first step in resolving a conflict with your teammates is to ___.Discuss possible solutionsAllow everyone to describe the problemAdmit to each other that there is a conflictAnalyze and discuss the problem

The first step to solving a job-related problems is to____.Choose a solution Define the problemMonitor the problemAnalyze and discuss the problem

One of the most common barriers to problem solving is ___.Fear of failureClosed-mindednessInability to communicate wellLack of motivation

Each of the following would be considered company-confidential except_____.Your companys strategic planOur companys addressEmployee salariesA contract bid

Printed text or pictures can be copied into an electronic format using a ___ScannerPlotterHard driveMonitor

Printed text or pictures can be copied into an electronic format using a ___ScannerPlotterC) Hard DriveMonitor

Suppose you own your own construction business and you want to create some brochures advertising your business. You would use ____ software to do this.SpreadsheetCADDesktop publishingE-mail

Alcohol falls into the class of drugs called ___.StimulantsAmphetaminesBarbiturates hallucinogens

Two of the most common problems supervisors face on the job are ___ and ___.Gossiping sloppy workUnprofessional attitudes; poor work ethicsDishonesty; absenteeismAbsenteeism; lateness

Material inventories and employee information can be stored on computer ___Menus Word processorsDatabases Browsers

What type of technology allows you to communicate with other computers without using physical connectionBatteryRobotWirelesselectrical

Proper initiative means always acting on your ownTruefalse

Imagine you have a problem on your job site. Following the firve step problem solving procedure you choose a solution and implement it. However your solution doesnt solve the problem your next step should be to ____.Select another possible solutionConsult the employee handbookAsk someone else to solve the problemAbandon your efforts

The first step to starting a new business is to ___Establish a business philosophyDevelop a marketing planEvaluate the need for such a businessSelect a location for the business

A statement that explains how a company does business is called a(n)___Employee handbookCompany philosophyMission statementReference

Parts that cannot easily be handled by other types of machines are cut and formed by ___.CADsPDAsCMCsEDMs

Two of the most common problems supervisors face on the job are ___ and ___.Gossiping sloppy workUnprofessional attitudes; poor work ethicsDishonesty; absenteeismAbsenteeism; lateness

What type of technology allows you to communicate with other computers without using physical connectionBatteryRobotWirelesselectrical

Proper initiative means always acting on your ownTruefalse

Imagine you have a problem on your job site. Following the firve step problem solving procedure you choose a solution and implement it. However your solution doesnt solve the problem your next step should be to ____.Select another possible solutionConsult the employee handbookAsk someone else to solve the problemAbandon your efforts

The first step to starting a new business is to ___Establish a business philosophyDevelop a marketing planEvaluate the need for such a businessSelect a location for the business

A statement that explains how a company does business is called a(n)___Employee handbookCompany philosophyMission statementReference

If you have a conflict with your supervisor, you should first ____ . Write down your thoughtsThink about the cause of the conflictLeave a message for your supervisorDiscuss it with your teammates

The chips and circuits that enable a computer to perform its functions are contained in the ___CD-romCPUHVACPDA

A hand saw hat is used for rough cutting , such as cutting access holes for piping and electrical boxes, is commonly called a __ saw. KeyholeBackDovetailCoping

Which of the following tasks is commonly done with a power stapler but not with a power nailer.Installing ceiling tileApplying deckingApplying roofing materialApplying sheathing

The edge shown below is known as a ___ cut. MortiseBevelDadoChamfer

A portable circular saw has ___A retractable upper blade guardRetractable lower and upper blade guardsA retractable lower blade guardA fixed (non-adjustable) baseplate

Which of the following operations would normally be done using a pneumatic stapler rather than a nailerConstructing cabinetsInstalling finish workInstalling insulationInstalling framing

A circular saw blade designed for cutting plywood should have ___ teethA small widely spacedLarge, widely spacedSmall, scissor-likeLarge, scissor-like

The hand plane that is generally used to plane long boards is the ___ plane.BlockJackSmoothingjointer

The main function of a router is to ___Plane lumberCut patterns in woodCut metalDrill holes

You should always use ___ when using a table saw to rip boards less than 4 wide

An auxiliary fenceHold-downsA miter gaugeA push stick

The sawbuck is generally used to ___Cut dimension lumber to lengthSupport lumber while it is being cutCut wide moldingsDo rip cuts

The tool shown below is a ___.Adjustable T-squareSliding T-bevelTry squareSpeed square

A type of cut often made with circular saw is called a ____ cut. ReadingPocketDadoRabbet

A major difference between a builders level and a transit level is that the ____.Transit level can be moved up and downBuilders level can be used to plumb columnsTransit level cannot be used to check elevations Transit level can only move in the horizontal plane.

A type of adjustable square that can be used to set, test, and transfer angles is called a ___Sliding T-bevelTry squareMiter squareSpeed square

The ___ clamp is commonly used to secure round, oval, and oddly shaped work. SpringWebHandscrewQuick

Information about the structure or assembly is provided in the ____.BorderDrawing areaTitle blockLegend

Dimension lines end with ___.An x symbolArrows Circlessquares

The symbols used for each type of plan should be indicated on the ___.Title blockTitle sheet Scalelegend

The project is identified by the ___.company logoSheet titleScale Drawing number

On a grid, the ___ are normally across the top and the ___ are on the sidesletters;numbersKeynotes;numbersNumbers;lettersNumbers;keynotes

Site plans are developed using a(n) ____ scaleengineersNTSFloating Architects

Plans used for work that has to do with construction in or on the earth are called ___ plansStructuralSpecificationArchitecturalcivil

To clarify any discrepancies in the plans, use a(n) ___.HVACRFIIndexlegend

The lines commonly used on a blueprint are sometimes called the ___ of lines.LanguageAlphabetCollectionDirectory

to avoid confusion, the gridline system omits the letters___.u, v, wI,J,TM,N,HI,O,Q

The ___ form of an architects scale is commonly used because it contains a variety of scalesTriangularStraight edgeRight angleoval

A grid divides an area into small parts called ___.BaysSquaresPocketsregions

The dimensions is a measurement written as a ___.NumberSymbolLetterkeynote

On a blueprint, a dimension is located ___ the dimension line

AboveBelowAt the end ofNear the middle of

A keynote is a number or letter that is often used instead of symbols and usually appears in ___.A square or circlesThe upper left hand cornerBlock lettersThe upper right hand corner

The accuracy of a level depends on its ___.HeightWidthLengthWeight

Pliers that have serrated teeth that grip flat, square ,round, or hexagonal objects are called ____.needle-noseLinemanLocking Groove-joint

The ___ a steel rule is, the more accurately it measures.LongerThinnerHeavierWider

Depending on the type of utility knife, you can lock the blade in ___ different positions.FiveFourThreeSix

Which saw can fit in tight places that larger handsaw cannot?Dovetail sawCoping sawHacksawCompass saw

To use a square shovel, push the ___ of the shovel against the material to be moved and push until the shovel is loaded.Turned ridgeLeading edgeTipFoot balance

What kind of bar has two claws (one at each end) and is ground to a slant on both ends?cats pawChiselPincerFlat

A come-along, used to pull heavy loads horizontally over the ground for short distances, is also called a ___.Pulley Chain-fallTackleCable pluller

A come-along, used to pull heavy loads horizontally over the ground for short distances, is also called a ___.Pulley Chain-fallTackleCable puller

A screw driver is made up of a handle, a ___, and a blade.ShankThreadWedgeClaw

A carpenters square consists of a blade and a ___, which make up a 90- degree angle.Groove Slat ShaftTongue

The end of the socket that fits in the handle is __HexagonalSquareRoundoval

When using an adjustable wrench, he first step is to ___.Pull the wrench toward youMake sure there is enough room for your fingersset the jaws to the correct size for the nut or boltFully tighten the jaws around the work

Some chalk lines can also be used as a ___. WedgeMeasuring tapeSteel rulePlumb bob

A heavy-duty tool used to drive posts or other large stakes is a ___HammerWedgeMalletSledgehammer

Ball peen hammers are classified by __.ColorWeight Materiallength

Pencil grinders are used to___.Grind away hard, heavy materialsSmooth the inside of materials such as pipeRemove rust and buff metalSmooth and polish intricate work

An example of an AC source of power is __.A batteryAirFluid pressureA wall plug

A power miter saw combines a miter box with a ___.Crosscut nail Nail-cutter sawCircular sawbandsaw

Portable belt sanders use continuous-loop abrasive belts stretched between two __.Springs DrumsDowelsWheels

A porta-power is an example of a(n) ___ tool. PneumaticElectricBatteryHydraulic

Saws with fine blades that are excellent for delicate and intricate cutting are called ___ saws.Worm-driveSaberReciprocatingcircular

The gunpowder cartridges used to power a powder-actuated tool are called ___.CompressorsBoostersCanistersBreakers

The first step when using a pneumatically powered nailer is to ___. Load the nails into the nailerRead the manufacturers instructionsCheck the air compressorInspect the nailer for damage

To prevent electrical shock, power tools should not be operated without the proper ___.ChuckPressureGFCIRPM

Drill bits are held in place by ___AugersGripsChucksCarbides

Blue print measurements most often are given in centimeters or ___.MillimetersDecimetersLitersKilometers

Area is the measurement of the ___ of an object

VolumeDepthSurfaceperimeter

Yesterday the job site received a gravel delivery of 5.7 cubic yards. The contractor has already used 2.3 cubic yards. The contractor has ___ cubic yards of gravel left.3.49.84.38.9

8/12 -4/8 = ___, reduce your answer to the lowest term.4/241/62/141/7

The formula to calculate the area of a rectangle is ___.Length x width0.5 x base x heightPi x radiusLength x width

You have to lay a floor for a 14- foot square shed. The area is ___ square feet. 144.019.628.0196.0

One sheet of drywall weighs 48.7 pounds. You have ordered 50 sheets, so your total order will weigh ___ pounds.2,430.0243.52,532.02,435.0

To clear a calculator, you must press the ___ key.CMRMON/CM+

While the measurement of the individual angles in a triangle can vary, their sum is always ___ degrees. 3601804590

To measure angles, you use an instrument called a __.PythagorasPerimeterProtractorvertex

You need to mix 42 pounds of mortar. Each pound of mortar mix requires 0.03 liters of water . How many liters of water do you need ? (round your answer to the nearest tenth.)1.3122.61.2613.2

Blue print measurements most often are given in centimeters or ___.MillimetersDecimetersLitersKilometers

What is the first step to finding the lowest common denominator of two fractions?Find the lowest common multiple of the denominatorsConvert each fractionReduce each fraction to its lowest terms multiply the denominators together

The most efficient way to add the same number together many times, is __.Multiplication SubtractionDivision Addition

What is the lowest term of the fraction 4/321/82/162/81/16

A yardstick is a standard ruler that is ___ feet long4532

When dividing , the number you are dividing by is called the ____. UnitDividendFractiondivisor

You have a piece of pipe that is 150 feet long. If you cut the pipe into 10 pieces of equal length , how long with each piece of pipe be?10 feet5 feet50 feet15 feet

If you have 364 boxes of drywall screws that must be divided equally between 7 job sites how many boxes does each site get ?56525054

+ =5/8 4/85/4

1/4 + 3/8 =5/8 4/85/4

The amount of space occupied in three dimensions is its___ . It is measured in cubic inches, feet and yards.AreaVolumeLengthcircumference

Area is the measurement of the ___ of an object

VolumeDepthSurfaceperimeter

You need to mix 42 pounds of mortar. Each pound of mortar mix requires 0.03 liters of water . How many liters of water do you need ? (round your answer to the nearest tenth.)1.3122.61.2613.2

A ___ is any one of the numeric symbols from 0 to 9.

DigitNumber Valuesymbol

A screw is 3-7/10 inches long. Using decimals, this is written as __ inches 3.303.603.133.70

The bottom number of a fraction is the ___.NumeratorDenominatorNegativepositive

Put the following decimals in order from smallest to largest: 0.012, 0.210, 0.112,0.2010.012, 0.112, 0.201, 0.2100.210, 0.112, 0.012, 0.2010.112, 0.210, 0.201, 0.0120.201, 0.210, 0.112, 0.012

When converting a percent to a decimal, you must first drop the percent sign. You then move the decimal point ___ place(s) to the ___two; leftone; rightOne; leftTwo;right

When converting a percent to a decimal, you must first drop the percent sign. You then move the decimal point ___ place(s) to the ___two; leftone; rightOne; leftTwo; right

Subtracting one number from another is finding the ___ between them

Place valueDifferenceTotal Sum

If you are adding 54 + 32, you will need to ___ the tens part of the sum from the units column to the tens column and add it there.CarrySumMoveTotal

When dividing fractions, the first step is to ___the fraction you are dividing byMultiplyInvertReduceConvert

Whole numbers are complete units without ___ or decimals DigitsSymbolsValuesfractions

7/8 x3/9 = ____ reduce your answer to the lowest term21/728/217/2424/63

The average American generates ________pounds of solid waste in a day.1.04.56.58.0

Using building materials that contain recycled materials is an example of a LEED ________ credit.Sustainable Sites Water EfficiencyEnergy and AtmosphereMaterials and Resources

Most energy consumed in the United States is produced using _______. A) fossil fuels B) renewable resources C) solar power D) nuclear energy

Everyday products require ______ energy to be produced.Alternative MinimalA large amount of energyrenewable

A vehicle produces the greatest amount of air pollution when the____.Engine is coldEngine is hotEngine is idlingVehicle is operating at high speeds

A vehicle produces the greatest amount of air pollution when the____.

Engine is coldEngine is hotEngine is idlingVehicle is operating at high speeds

The area of human activity that consumes the most energy is ______.

TransportationBuilding construction and operationIndustrial manufacturingHeavy engineering and infrastructure

A brownfield is a(n) _________.WetlandWildlife refugeEcological resourceArea that may be contaminated

Rainwater harvesting and gray water are ________.Alternative sources of waterUnsustainableContaminated with pathogensUnsafe sources of water

The single greatest contributor to the U.S. carbon footprint is ______.DeforestationAquifer depletionFossil fuel useSoil erosion

Bioswales are engineered basins used to ______.Percolate water back into the soilConvey water to the storm water sewer Transport water to the treatment plantContaminate local streams

Deforestation contributes to global warming by ___________.

Increasing runoffIncreasing stream pollutionDecreasing habitatsCausing an imbalance in the carbon cycle

All of the energy required to produce a consumer product is termed ______ energy.EmbodiedRenewableRecycledProduction

All of the energy required to produce a consumer product is termed ______ energy.

EmbodiedRenewableRecycledProduction

Appliances that perform in the top 25 percent of their product class in terms of energy use are called ______.Energy BestLEEDEnergy StarGreen

The cost of building a green facility should be considered __________.

When selecting the siteWhen selecting materialsDuring constructionThrough its entire life cycle

Changes that make the most difference with the least amount of effort are __________.

Life cycle cost analysisMaterial choicesLeverage pointsGreen idea

The predominant national green building rating system in the U.S. is___________.LEEDGreen AdvantageLean Construction InstituteU.S Green Builders

A green building rating system is a ________.

Consistent way to evaluate and compare buildingsMandatory requirement for home loansDecorating standardMethod of site selection

The lowest level of LEED certification that a building can achieve is ______.

PlatinumGoldSilverCertified

The lowest level of LEED certification that a building can achieve is ______.PlatinumGoldSilverCertified

According to the LEED certification standard, a building earning 52 points would be _________.PlatinumGoldSilverCertified

The first step in the LEED certification process for a building is ________.Design reviewProject registrationTechnical supportOwner notification

The LEED credit that covers construction activity is _______.Sustainable SitesWater EfficiencyEnergy and AtmosphereIndoor Environmental Quality

Using locally available materials for construction is an example of a LEED _______ credit.Materials and ResourcesEnergy and AtmosphereWater EfficiencySustainable Sites

Using locally available materials for construction is an example of a LEED _______ credit.

Materials and ResourcesEnergy and AtmosphereWater EfficiencySustainable Sites

The LEED credit that reward projects that address local environmental issues is ________.Materials and ResourcesRegional PriorityInnovation in DesignEnergy and Atmosphere

The LEED credit for building with low-emission materials is ________.Sustainable SitesMaterials and ResourcesIndoor Environmental QualityEnergy and atmosphere

A construction phase pitfall to achieving LEED certification is ______.Using heavy equipmentLack of owner agreementSloppy documentation of products usedDesign errors

When flushing out a building the EPA recommends that the building be flushed for a period of _______ with 100 percent outside air.1 day2 days1 week2 weeks

1 day2 days1 week2 weeks

When flushing out a building the EPA recommends that the building be flushed for a period of _______ with 100 percent outside air.

The basic components of the LEED certification system are _________.Regulations and lawsPrerequisites, credits and pointsRecycled and reused materials Materials and methods

The Indoor Environmental Quality Credit for thermal comfort verification requires a(n) ____ after one year of occupancy.Thermal comfort surveyThermostat recalibrationAirflow analysisTemperature variation analysis

Lack of coordination with other trades affects your LEED certification because of __________.Increased labor disputesReduced overall energy performanceIncreased change ordersBuilding hazards

A best practice for building sites that want to achieve LEED certification is to select the right ___________.ArchitectLocationContractorSubcontractor

To lower the center of gravity when moving materials, you should always place the __________. Lightest load on the bottomLongest load on topHeaviest load on the bottomHeaviest load on top

What is the appropriate vehicle to use for lifting and moving heavy loads on smooth surfaces ?Georgia buggyIndustrial forkliftPipe transportPowered wheelbarrow

What is the proper procedure to lift objects ?Bend over with your knees straight, feet together, and then lift.Lift with your back, keep your legs straight, and keep your arms up.Lift with your legs, keep your back straight, and keep your head up.Lift with your arms, keep your legs straight, and keep your head up.

What is the proper procedure to lift objects ?Bend over with your knees straight, feet together, and then lift.Lift with your back, keep your legs straight, and keep your arms up.Lift with your legs, keep your back straight, and keep your head up.Lift with your arms, keep your legs straight, and keep your head up

In order to work with motorized materials-handling equipment, you must be _________.Trained, certified, and authorizedExperienced and knowledgeableA job foreman or supervisorLicensed to drive

Before attempting to lift any materials, you should ___________.Look for any protruding nails, wires, or sharp edgesUse a safety harnessAsk your supervisor for helpEnsure the stacking ratio is no greater than 3:1

What non-motorized materials-handling device uses force applied with a lever, screw, or hydraulic press to raise heavy objects?Industrial forkliftPorta-PowerHand truckJack

Before using a materials-handling device, you must ___________.Inspect itClean itLubricate itCharge it

When moving a material cart on an inclined or declined surface, you must be sure _________.The load does not exceed the labeled weight capacity.The hand brake is within your reachThe hydraulic ram has been removedThe load is cushioned with moving pads to prevent slippage

You can have trouble transporting a load that is ______________.ContainerizedLong and cumbersomeShrink-wrappedpalletized

When using hand signals, you must always ________________.Be certified and authorizedWear reflective glovesKeep eye contact with the operatorMake sure you can hear the backup alarm

When working with cables and a pull system, it is acceptable to use _______.Another cable or wireA low stretch ropeA rope with a lower load rating than the forceA high-stretch rope

Which of the following is considered a load in relation to materials handling?A portable generator powering a nail gunAn elevator carrying workers and tools to an upper floorA pneumatic compressor powering a pavement breakerA cement mixer pouring cement into a form

What is the diameter of the fall zone when working around a forklift ?A minimum of thirty feetTwice the length of the base of the forkliftTwice the height of the object being liftedTwice the width of the object being lifted

What device may have a rotating table surface and/or spikes on the table surface for a better grip ?Roller skidsPallet jackPallet conveyorAccumulating conveyer

In material-handling jargon, the quantity of materials that can be transported at one time by a machine or vehicle is called a _______.StackLoadShipmentConsignment

In material-handling jargon, the quantity of materials that can be transported at one time by a machine or vehicle is called a _______.StackLoadShipmentConsignment

**************************************************************************************************************************************************************************************************************************************************************************************************************************

core review 2012-2013 04

Documents

work area

light duty household250

medium duty commercial200

extra duty professional225

heavy duty industrialwork

onthejob safety rests

safety harness

ear infections