contor viko multi phase

7/27/2019 Contor Viko Multi Phase

1/16

1

OPERATION MANUAL

THREE-PHASE MULTI TARIFF-DEMANDMETER

ACTIVE

ELECTRONIC ELECTRICITY METER

MODEL : VEM-T5100DB0

MODEL : VEM-T5100DB2


2/16

2

CONTENTS

GENERAL INFORMATION AND WARNINGS ...3

TYPE CODE TABLE............3

GENERAL FEATURES...................................... .....4

TABLE OF PRODUCT SPECIFICATIONS............ 5

FUNCTIONS..........5

INSTALLATION INSTRUCTIONS.........6CONNECTION DIAGRAMS............7

RS485 CONNECTION INFORMATION.............7

DISPLAY SYMBOLS.......8

DISPLAY INFORMATION..9

SUB-MENU INFORMATION.......................10-11

SECOND SUB-MENU INFORMATION..............13-15

ERROR WARNING DISPLAYS.........14

COMPANY AND TECHNICAL SERVICE INFORMATION...15

GENERAL INFORMATION AND WARNINGS


3/16

3

This manual provides information regarding the specifications, installation and operation of the VIKO BRAND,

VEM-T series Electronic Electricity Meters.

PLEASE READ THIS MANUAL CAREFULLY BEFORE ATTEMPTING TO INSTALL OROPERATE THE METER!

THE INSTALLATION OF THE METER MUST BE PERFORMED BY QUALIFIED PERSONNEL,IN ACCORDANCE WITH THE METERS OPERATIONAL INFORMATION.

POWER LINES MUST BE DISCONNECTED DURING THE INSTALLATION AND

DISASSEMBLY OF THE METER. COMING INTO CONTACT WITH PARTS THAT ARE CHARGED WITH VOLTAGES POSE

LETHAL RISK.

THE METER MUST BE OPERATED IN ENVIRONMENTS HAVING TEMPERATURESBETWEEN THE VALUES SPECIFIED WITHIN THIS MANUAL.

THE EXTERIOR SURFACE OF THE METER SHOLD NOT BE CLEANED USING ABRASIVEMATERIALS.

THE CALIBRATION AND PROGRAMMING OF THE METER IS CARRIED OUT DURING THEPRODUCTION PHASE AND EACH METER IS OFFERED AFTER CONDUCTING QUALITY

CONTROLS. THERE ARE NO MAINTENANCE OR PROGRAMMING ACTIVITIES THAT MAY

BE CONDUCTED BY THE USERS.

This manual is the property of Viko, and it may not be copied, reproduced, or lent to third parties.

All information contained herein is current information at the time of printing. VIKO reserves the right to make

changes without prior notification.

Scope of the Guarantee

Our meters are guaranteed against production flaws for a period of five (5) years. The damages that may arise

due to installation and operation of the meters that are not in accordance with the information stated in this

manual are excluded from the scope of the guarantee.

Servicing or maintenance may only be performed by VIKOs authorized technical service personnel or other

persons or organizations that are authorized by VIKO. The damages that may arise due to the servicing or

maintenance performed by unauthorized persons renders the guarantee void.

VIKO BRAND, VEM-T series Electronic Electricity Meters are designed and produced in accordance with the

most current international standards applicable in Turkey. The meters are designed to provide precise readings,

with the help of high-tech components for flawless operation over long periods of time in accordance with themost current international standards to provide ease of use while possessing physical qualities that are able to

satisfy site requirements.

The meter satisfies the following standards:

TS EN 50470-1

TS EN 50470-3

TS EN 62054-21

TS EN 62056-21

METER TYPE CODE TABLE


4/16

4

PRODUCTCODE

TYPE OFMEASUREMENT CURRENT TYPE OF CONNECTION

MEASUREMENTCLASS

COMMUNICATIONOUTPUT TYPE

VEM - X XXXXX X X X X

VIKO ENERGYMETERING M = MONOPHASE 1080 D = DIRECT CONNECTION A = CLASS A 0= NOT

NULLCHARACTERNORMAL

T = THREEPHASE 10100C = WITH CURRENTTRANSFORMER B = CLASS B 1= RS232

P= WITHADVANCEPAYMENT

C = COMBI x5V = WITH CURRENT/VOLTAGETRANSFORMER C = CLASS C 2= RS485

1060 3= PLC5(80)

5(100)

General Features

Active energy measurement

Active demand measurement

Has a timer and calendar that may operate during power outages.

Automatic daylight saving adjustments in accordance with the EU norms in force Technical hardware that allows for canceling the application of daylight savings or makes it possible to

alter the times.

Storage of the data belonging to the previous year.

8 time zones and 4 tariffs, the tariffs may be altered without having to remove the meter from where it isplaced.

Communication through an optical port

Large LCD display for ease of reading

Availability of information from the optical port and LCD display even if there is a power outage.

Ability to view the electric terminal cover and top covers (open/closed) positions on the LCD display

Critical battery level warning

Timer error warning

60 day demand profile

Ability to set the index information displayed on the LCD display in 5 integers and 3 decimals, 6integers and 2 decimals or 7 integers and 1 decimal.

Displaying of the active operational direction for all phases on the LCD display

Phase sequence error warnings

Demand definition and displaying of warnings in the event of exceeding demand

THE FOLLLOWING INFORMATION ARE DISPLAYED IN THE SUB-MENU THAT CAN BE

ACCESSED BY PRESSING AND HOLDING DOWN THE METER READING BUTTON.

Displaying of the index information of the previous month on the LCD display Displaying of the voltage levels for each phase on the LCD display

Displaying of the voltage levels between phases on the LCD display

Displaying of the current values for each phase on the LCD display

Displaying of the power factor values for each phase on the LCD display

Displaying of the network frequency for each phase on the LCD display

Displaying of the power values for each phase on the LCD display

Displaying of the total power passing through the meter on the LCD display

TABLE OF PRODUCT SPECIFICATIONS


5/16

5

MODELT5100DB2T5100DB0

T10100DB2T10100DB0

TYPE OFCONNECTION

THREEPHASE,3 PHASE4 WIRES

THREEPHASE,3 PHASE4 WIRES

CURRENT CIRCUITPOWER CONSUMPTION

< 2 W 10 VA

OPERATING VOLTAGE 230/400 V 230/400 VVOLTAGE CIRCUITPOWER CONSUMPTION


6/16

6

HOLDING PART : They are used during the installation of the meter. The position of the part of the meter

can be adjusted vertically with the help of the adjustment screws found on the back of the meter.

LCD DISPLAY : It displays the information gathered by the meter.

OPTICAL PORT : It is a communication unit that enables communication between the meter and a handheld terminal or computer for the programming of permitted parameters or for the reading of the information

gathered by the meter.

READING BUTTON : It is the button that successively updates the informaton gathered by the meter on the

LCD display. If the meter button is not pressed, the display information will be updated automatically every 5

seconds and displayed on the screen. The automatic screen will start to operate 30 seconds after a reading has

been conducted using the button.

TOP COVER SEAL: It is a seal affixed after the production, quality control and calibration procedures of the

meter have been conducted. Due to the fact that legal action may be taken against unauthorized persons

that tamper with these seals, the seals shall not be removed or damaged.

TERMINAL COVER SEAL: It is an area where the distribution company must affix their seals in order to

prevent unauthorized access to the electric terminal block where the meter connections are made. Due to the

fact that legal action may be taken against persons that have not been authorized by the distribution

company but tamper with the electric terminal seals, the seals shall not be removed or damaged

TERMINAL COVER : It is the part which covers the area where the meters connections are made. In the

event that the covers are opened, the information at the time of opening of the covers are recorded in the

devices memory. After installation, power is supplied after the covers have been closed. There is a part

underneath that may be broken off for the cables to be inserted.

Fi ure 1 Fi ure 2


7/16

7

INSTALLATION OF THE METER AND ITS SEALS

The meter is installed by the help of the installation part located on the top of the device and the three

installation holes found on either bottom side of the device. The dimensions of the device are shown in

figure 1, and the installation holes are shown in figure 2.

The VEM-T series electronic electricity meters are protected against unauthorized use with the help of atotal of 3 seals of which 2 are calibration seals and 1 is an electric terminalcover seal.

INSTALLATION INSTRUCTIONS

1- Install the meter using the installation holes as shown in figure 2.2- Make the phase and neutral connections in accordance with the connection diagram.

(While the connections are being made, make sure that the tips of the cables are properly stripped,

that the connection screws in the electric terminal are tightened in a way that does not damage the

conductor, and that no faulty connections are made.)

3- Before applying voltage, make sure that the electric terminal cover and the electric terminal coverbutton are closed.

4- Apply voltage and current. In the event that the directions of the current and voltage connections aremade in reverse, the phase that has been connected in reverse will be displayed on the screen as phase

P. In the event that the phase sequence has been connected in reverse, the R-S-T symbols flash on the

meter display. When this happens, control the meters connections after you have disconnected the

power. In the event that the meter is properly connected and the three phases are energized, the R-S-T

symbols will light up constantly. In the event that the current polarities are properly connected a + P

symbol will be displayed on all phases.

CONNECTION DIAGRAM OF A THREE-PHASE METER

RS 485 CONNECTI ON


8/16

8

VEM-T10100DB2MODEL: The RS485 outputs are supplied as standard components in our VEM-T5100DB2

Three-phase meters. It is possible to obtain a read-out from the meters thanks to these outputs. It is possible to

access numerous meters by connecting these outputs in parallel. The protocol structure for communicating with

the meters is as follows: Communicating structure is in accordance with the TS EN 62056-21 standard.

Communication established!

Baud Rate 300

--> /?00012835![CRLF]

[ACK]051

--> [ACK]051

Baud Rate 9600

--> [SOH]R2[STX]0.0.0()[ETX]P

[SOH]B0[STX]0.0.0()[ETX]P

--> [SOH]B0[STX]0.0.0()[ETX]P

Communication shut down!

DISPLAY SYMBOLS

Timer error warning

Lights up when information related to date is displayed on the LCD screen.

Lights up when information related to time is displayed on the LCD screen.

Battery warning

The section where OBIS codes of the information displayed on the meter screen is shown.

The numerator where the information contained in the meter is displayed.

The section that indicates which tariff information belongs to the tariffs

Indicates the tariff that the meter keeps records in.

The symbols indicating the direction of the current passing through the meter. When thesymbol +P is displayed on screen, it means that the connections of the meter have beenproperly made. When the symbol +P is displayed on screen, it means that the meters current


9/16

9

connections have been made in reverse.

It is displayed on the screen in the event that voltage is applied on the phase connections, it lights upconstantly when the connections have been made properly, and it flashes when there is an error in thephase sequence.

Indicates that the information displayed on the screen is related to demand.

Indicates the measurement units of the information displayed.

Terminal cover opening warning.

Top cover opening warning.

Displayed when information regarding reactive consumption is displayed on screen.

DISPLAY INFORMATION

DATE

TIME

TOTAL ACTIVE ENERGY

TARIFF 1

ACTIVE ENERGY

TARIFF 2

ACTIVE ENERGY

TARIFF 3ACTIVE ENERGY


10/16

10

TARIFF 4

ACTIVE ENERGY

CURRENT PERIOD (MONTH) ACTIVE ENERGY

P-MAX VALUE

DATE OF INFORMATION OF

ACTIVE ENERGY PMAX

TIME OF INFORMATION OF

ACTIVE ENERGY PMAX

Can be read in sequence by pressing the display information reading button. The automatic screen that operates 30 seconds after the

display button is pressed, indicates the information on screen at 5 second intervals.

SUB-MENU INFORMATIONThe sub-menu can be accessed by pressing and holding down the meter reading button for 3 seconds. The latest

demand reset information for the meter is displayed in the sub-menu. To exit the sub-menu, the reading button

must be pressed and held down for 3 seconds. If the meter is left in the sub-menu, it will return to the main

menu automatically after 30 seconds.

SERIAL NUMBER

PREVIOUS PERIOD TOTAL

ACTIVE ENERGY

PREVIOUS PERIOD TARIFF 1 TOTAL

ACTIVE ENERGY


ACTIVE ENERGY


ACTIVE ENERGY


11/16

11


ACTIVE ENERGY

PREVIOUS PERIOD (MONTH) ACTIVE ENERGY

P-MAX VALUE

PREVIOUS PERIOD

DATE OF INFORMATION OF

ACTIVE ENERGY PMAX

PREVIOUS PERIOD

TIME OF INFORMATION OF

ACTIVE ENERGY PMAX

DATE OF THE OPENING

TERMINAL COVER

TIME OF THE OPENING

TERMINAL COVER

NUMBER OF TIMES TERMINAL

COVER HAS BEEN OPENED


12/16

12

2. SUB-MENU INFORMATION (OPERATIONAL INFORMATION)The following information may be accessed in the meters 2nd sub-menu. To display the menu on the screen,

the reading button must be pressed and held down for 6 seconds. The first sub-menu is displayed 3 seconds

after the menu button is pressed, and if the button is kept held down for 6 seconds, the second sub-menu is

displayed. The menu button must be pressed for a long period of time to exit the sub-menu in question. If the

meter is left in the second sub-menu, it will return to the main menu automatically after 30 seconds.

R PHASE VOLTAGE VALUE

S PHASE VOLTAGE VALUE

T PHASE VOLTAGE VALUE

VOLTAGE VALUE BETWEEN R-S PHASES

VOLTAGE VALUE BETWEEN R-T PHASES

VOLTAGE VALUE BETWEEN S-T PHASES

R PHASE CURRENT

S PHASE CURRENT


13/16

13

T PHASE CURRENT

R PHASE ACTIVE POWER

S PHASE ACTIVE POWER

T PHASE ACTIVE POWER

R PHASE REACTIVE POWER

S PHASE REACTIVE POWER

T PHASE REACTIVE POWER

R PHASE APPARENT POWER

S PHASE APPARENT POWER

T PHASE APPARENT POWER


14/16

14

R PHASE COS VALUE

S PHASE COS VALUE

T PHASE COS VALUE

R PHASE FREQUENCY

S PHASE FREQUENCY

T PHASE FREQUENCY

ERROR WARNING DISPLAYS

Terminal cover opening warning.

The meter is designed to detect and record instances when the cover used for covering the terminal section that

the connections are made is opened. For the meter not to keep records of any opening of the covers during the

initial installation of the meter, the cover opening records are not kept until the meter records indexes. However,

a warning flashes to indicate the opening of the electric terminal covers. If the index that is required for

keeping record has not passed through the meter, the warning on the screen disappears after the covers are

closed. In order for records to be kept after the meter is installed, the terminal covers must be closed, and the

necessary index must be passed through the meter. If the recording of the opening of covers is activated, themeter, records the date and time of the first opening of the covers in each month and counts, records, and stores

the number of times they have been opened during the month. This information may b e accessed in the meters


15/16

15

sub-menus. During the passage to the next month, it stores the current information in its memory as the

previous months information and resets the information for the next month. It keeps recording the openings of

the covers in the next month as described above. If a month passes with the cover of the device open, it records

the date of the passing of the month as the initial opening of the covers, but indicates the number of openings as

0.

It is possible to delete the electric terminal cover opening warning through conducting optical readings from the

meter. Optical readings only delete the warning on the device display, the stored memory regarding the

openings are not erased. .

Top cover opening warning:

The device is designed to detect, record and store the date and time of the opening of the cover that covers the

section where the measurement section is located. The top cover should not be tampered with, as the opening

of the top cover which has been sealed will be regarded as attempting illegal use. When the cover is opened, a

flashing warning for the opening of the top cover will be displayed on the screen. The date and time of theopening of the top cover will be recorded and stored in memory. Only the first opening of the covers will be

recorded, and subsequent openings will be ignored. It is only possible to reset the warning for the opening of

the top cover by authorized personnel in the factory environment.

Battery warning:

Appears on the screen when the battery supplying power to the meters timer is at a critical level. Due to thefact that the battery is place underneath the top cover, it must be replaced by authorized service personnel.

Contact our technical service in the event that a warning is displayed.

Timer error warning:

Appears on the screen when there is an error associated with the timer. In this case, the meters tariff function is

disabled and it records the whole index as a T1 tariff. Please contact our technical service in the event that a

timer error warning is displayed.


16/16

16

COMPANY DETAILS

COMPANY TITLE: VIKO Elektrik ve Elektronik Endustrisi San.ve Tic. A.S.

ADDRESS: Abdurrahmangazi Mah. Ebubekir Cad. No:44

34887 Sancaktepe-Samandira / Istanbul

Tel : 0 216 564 55 55

Fax: 0 216 564 55 05

Web:www.vikosayac.com

TECHNICAL SERVICE ADDRESS

Abdurrahmangazi Mah. Ebubekir Cad. No:44

34887 Sancaktepe-Samandira / Istanbul

Tel : 0 216 564 55 55

Fax: 0 216 564 55 66
http://www.vikosayac.com/http://www.vikosayac.com/

contor viko multi phase

Documents