content · 2406-1006 optic injector metal ferrule col-umn id 0.32mm h100021 has been replaced by...
TRANSCRIPT
2
Content Page
OPTIC Liners 3
OPTIC 2
Consumables 5
OPTIC 3
Consumables 7
Spare Parts 9
OPTIC-4
Consumables 12
Spare Parts 13
OPTIC accessories 15
LINEX
Consumables, spare parts 16
PHASER
Consumables 17
Spare Parts 18
2
3
OPTIC Liners
Part number Description Explanation
2414-1001 Fritted Liner This liner contains a medium porosity frit made . This liner can be used for hot
and cold Split/Less injections. In addition, if used with a suitable packing material
the liner can be used for large volume injection, thermal desorption, solid sam-
pling and pyrolysis applications.
2414-1003 Single-Necked Liner This liner is specially made for hot or cold split injections. The large internal
diameter of 3.4 mm facilitates mixing of the sample with the carrier gas.
2414-1005 Splitless Liner This liner is for hot and cold splitless injection of sample volumes below 1 µl. The narrow internal diameter of 1 mm ensures fast transfer of the sample to the column under splitless conditions. We advise this liner for SPME techniques.
2414-1007 Sintered glass liner This liner is both very inert and capable of operation up to 350°C. As such it is
suitable for the large volume injection of compounds that have the tendency to
breakdown. The capacity of the liner is lower than that of a packed liner (about
50 µl, depending upon solvent used). To maximize its capacity, the liner should
be used in combination with a syringe fitted with a dome tipped, side-hole nee-
dle.
2414-1008 Special deactivated
Sintered glass liner
This liner is both very inert, highly deactivated and capable of operation up to
350°C. As such it is suitable for the large volume injection of compounds that
have the tendency to breakdown. The capacity of the liner is lower than that of a
packed liner (about 50 µl, depending upon solvent used). To maximize its capac-
ity, the liner should be used in combination with a syringe fitted with a dome
tipped, side-hole needle.
2414-1009 Baffled Splitless
Liner
This liner is for hot and cold splitless injection of sample volumes below 1 µl. The
narrow internal diameter of 1 mm ensures fast transfer of the sample to the
column under splitless conditions. With this liner the sample will not have any
chance of being injected directly to the bottom of the injector. This liner will give
better results for the high boiling components.
2414-1011 Fritted liner with
taper
This liner contains a medium porosity frit made from sintered, deactivated glass.
With a taper on the bottom. This liner can be used for split/less, thermal desorp-
tion, pyrolysis injections. In addition, if used with a suitable packing material the
liner can be used for large volume injection, thermal desorption, solid sampling
and pyrolysis applications.
2414-1013 LINEX DMI tapered
liner
This liner has special dents to hold the DMI-vail. This ensures that there will be
no compounds traps on the frit. The taper will increase sensitivity of the in-
creased linear velocity to the column, which will reduce peak width and increase
peak height
2414-1015 Needle Guide DMI
Tapered liner
The needle guide will ensure the automated introduction of sample in the DMI
Vial when using a extra long needled syringe
2414-1016 LINEX metal Needle
Guide
The needle guide will ensure the automated introduction of sample in the DMI
Vial when using a extra long needled syringe. Made out of metal
2414-1020 Fritted Liner packed
with
Chromosorb W
The liner contains Chromosorb W packing material that combines a maximum
operating temperature (350°C) with a high sample capacity (in excess of 100 µl in
most cases).
4
OPTIC Liners
Part number Description Explanation
2414-1021 Fritted Liner filled
with Tenax GR,
Mesh 80-100
The liner contains Tenax GR 80-100 mesh packing material that combines a
maximum operating temperature (350°C) with a high sample capacity (in excess
of 100 µl in most cases).
2414-1022 Fritted Liner packed
with Tenax GR,
mesh 60-80
Tenax GR is a porous polymer resin based on 2,6-diphenylene-oxide plus 30% Graphite. It is a widely used adsorbent resins for use with Purge and Trap Thermal Desorption for applications such as trapping VOC's in air and liquids. Tenax GR is especially beneficial in trapping volatile organics from high moisture content samples due to its low breakthrough volume for water. Tenax GR can be used with: Hydrocarbons, Alcohols & Glycols, Aldehydes and Ketones, Halogens, Amines, Aromatics and Terpenes.
2414-1023 Fritted Liner packed
with
Carbosieve III
Carbosieve SIII is a large surface area carbon molecular sieve which is ideal for
trapping the smallest organics. While it has a higher affinity for water than most
other resins, its small pore size provides the best trapping ability for the volatile
organics.
2414-1024 Fritted Liner packed
with Tenax GR and
Carboxen
The liner has a combination of Tenax GR and Carboxen.
To have the maximum advantage from the different packing materials.
2414-1025 Fritted Liner packed
with Tenax TA and
Carboxen
The liner has a combination of Tenax TA and Carboxen.
To have the maximum advantage from the different packing materials.
2414-1026 Fritted Liner packed
with Carbotrap
Carbotrap is graphitized carbon black that is an ideal adsorbent resin for the
trapping of a wide range of organic analytes from C4/C5 through the medium
boilers. It has a coarse mesh size (20/40) which prevent high backpressures in
the desorption tubes
2414-1027 Fritted Liner (frit on
15 mm) packed with
Tenax TA
The liner contains Tenax TA 60-80 mesh packing material that combines a maxi-
mum operating temperature (350°C) with a high sample capacity (in excess of
100 µl in most cases).
2414-1040 Starter Kit for LVI
Sampling, pack of 5
different liners
5 different liners to take maximum advantage of OPTIC inlet, when optimizing or
developing a method. Contains:
2414-1001, Fritted Liner with Frit at 15 mm
2414-1003, Splitless Liner
2414-1020, Fritted Liner packed with Chromosorb W
2414-1009, Baffled liner (splitless injections)
2414-1013, Sintered Glass Liner with Taper
2406-1010 DMI Sample Insert
30µl
The container for sample when using the DMI technique, volume 30 µl.
Pk/ 100
2406-1020 DMI Sample Insert,
60 µl
The container for sample when using the DMI technique, volume 60 µl.
Pk/ 100
5
OPTIC 2 Consumables
Part number Description
A100014
PTFE Covered Septum, 9 mm
Pk/50
A100015
Graphite Ferrule for 0.25 - 0.32
mm ID Column, Pk/10
A100016
Graphite Ferrule for 0.53 mm ID
Column, Pk/10
A100030
PTFE Reducing Ferrule, 1/8" to
1/16", Pk/10
A100041
High Quality Low Bleed Septum 9
mm, Pl/25
A100067
PTFE Top Boss Insulator,
Pk/10
A100111
Merlin Micro-seal ®
Pk/ 1
5
6
OPTIC 2 Consumables
Part number Description
A100120
Brass Liner Blanking Cap
Pk/10
A100122
Nylon Liner Blanking Cap
Pk/10
A1000141
Stainless Steel Liner Blanking Cap
Pk/10
A100124
Graphite Ferrule for 0.1-0.18 mm
ID Column, pk/10
6
7
OPTIC 3 Consumables
Part number Description
A100030
PTFE Reducing Ferrule, 1/8" to
1/16”
A100067
PTFE Top Boss Insulator
3007-11605
High resistance Silicon O-ring for
liner
H100001
General Purpose Red Septa 11
mm,
H100002
Has been replaced by
2406-1002
Low Bleed White Septum 11 mm
H100003
Has been replaced by
2406-1003
Graphite Ferrule for 0.53 mm ID
Column
H100004
Has been replaced by
2406-1004
Graphite Ferrule for 0.1 - 0.32 mm
ID Column
7
8
OPTIC 3 Consumables
Part number Description
H100007
Graphite/Vespel Ferrule
(for OPTIC 3 Special Tee)
H100009
O-ring for 1/4 Tube, 5.7 x 1.9
H100010
Empty tube for Thermal
Desorption 1/4
H100012
100 µl syringe for Shimadzu AOC
20i
H100013
OPTIC 3 HT Injection Port Septa
transparent
H100019
Has been replaced by
2406-1005
OPTIC Injector Metal Ferrule Col-
umn ID =<0.25mm
H100020
Has been replaced by
2406-1006
OPTIC Injector Metal Ferrule Col-
umn ID 0.32mm
H100021
has been replaced by
2406-1007
OPTIC Injector Metal Ferrule Col-
umn ID 0.53mm
H200139
has been replaced by
2406-2049
OPTIC injector metal nut for metal
ferrule,
8
9
OPTIC 3 Spare parts
Part number Description
H200001
has been replaced by
2406-2047
Stainless Steel Injector Bottom
Nut
H200002
Has been replaced by
2406-2010
Standard Septum Nut
H200003
Has been replaced by
2406-2012
Clamp Nut Insulator
H200004 Has been
replaced by 2406-
1002
Injector Bottom Insulation Cap
H200005
Has been replaced by
2406-2270
GC Oven Thermocouple
H200007
OPTIC 3 EGC Fitting 1/8"
9
10
OPTIC 3 Spare parts
Part number Description
H200008
Viton O-ring for EGC Fittings
H200037
One-touch mini connector for OP-
TIC 3 cooling valve
H200044
OPTIC 3 Charcoal Split Filter
Cartridge
H200050
Split Line Charcoal Filter
Assembly (H200044 + H200051)
H200139
Has been replaced by
2406-2039
OPTIC Injector Metal Nut for metal
ferrule
L200218
Fitting 1/16 OD tubing
10-32 thread
10
11
OPTIC 3 Spare parts
Part number Description
H400038
Solvent Monitor Assembly
H400058
Septum Nut Sampling connection
(1/16)
H500021
has been replaced by
2406-2048
Key for OPTIC Injector Bottom Nut
H500024
has been replaced by
2406-2039
OPTIC 3 Column Mounting Jig
L100007
has been replaced by
2406-1008
Liner O-ring
material: Viton
11
12
OPTIC-4 Consumables
Part number Description
2406-1017
OPTIC Low Bleed Red Septa
2406-1003
OPTIC Graphite Ferrule for 0.53
mm ID Column
2406-1004
OPTIC Graphite Ferrule for 0.1 -
0.32 mm ID Column
2406-1005
OPTIC Inlet Metal Ferrule, Column
ID 0.25mm
2406-1006
OPTIC Inlet Metal Ferrule, Column
ID 0.32 mm
2406-1007
OPTIC Inlet Metal Ferrule, Column
ID 0.53m m
2406-1018
OPTIC non-stick Liner O-rings
2406-1009
OPTIC EFC Inlet Connection o-ring,
12
13
OPTIC-4 Spare parts
Part number Description
2406-2039
OPTIC Column Mounting Jig
2406-2047
OPTIC Stainless Steel Inlet Bottom
Nut
2406-2048
Key for OPTIC Inlet Bottom Nut
2406-2049
OPTIC Inlet Bottom Nut for Metal
Ferrule
2406-2010
OPTIC-4 Inlet Septum Nut
Standard
2406-2013
OPTIC-4 Inlet Clamp Nut Insulator
2406-2015
OPTIC-4 Inlet Septum Nut,
Shimadzu type
2406-2016
OPTIC-4 Inlet Septum Nut Insert,
Shimadzu type
2406-4021
OPTIC-4 External Solvent Monitor
Assembly
13
14
OPTIC-4 Spare parts
Part number Description
2406-4205
OPTIC-4 Inlet Cooling Valve
2406-2051
OPTIC-4 EFC Fitting, 1/8" tubing
3007-16201
Shimadzu aluminum packing
type-G
2406-2257
Fuse, Slow Blow, 230V, 6.3A
2406-2269
OPTIC Inlet Bottom Insulation Cap
2406-2270
OPTIC GC Oven Thermocouple
2406-4025
OPTIC-4 Split Line Filter Assy
14
15
OPTIC Accessories
Part number Description
G300025
Gas Leak Detector LD239
3001-12101
Packing Funnel for Liners
3001-12701
Glass wool inserter
3001-12801
Glass wool remover
3001-12720
Septum Pick
3001-12730
Injector port cleaning Kit
3001-12745
Ferrule removal tool
2406-4164
Or
2406-4167
OPTIC Standard On-Column Tool
kit
Or
OPTIC On-Column Tool kit for
Shimadzu GC
15
16
LINEX Consumables
Part number Description
2406-1018
OPTIC non-stick Liner O-rings
L400020
Has been replaced by
2411-4107
CDCS Liner Caps Assy
2411-2046 Fitting 1/16" OD tubing, 10-32
thread
2411-2001 LINEX Bushing
LINEX Accessories
Part number Description
L200043
Has been replaced by
2411-2500
CDCS 98 position Tray for Capped
Liners
L200030
Has been replaced by
2411-2026
LINEX 98 position Tray, Plastic
L500001
Has been replaced by
LINEX Capping-De-Capping
Station 2.0
16
17
PHASER Consumables
Part number Description
3007-14105
Graphite Ferrule for 0.25 mm
column
3007-14108
Graphite Ferrule for 0.32 mm
column
3007-14110
Graphite Ferrule for 0.53 mm
column
3007-31104
Graphite Vespel ®Ferrule for <0.25
mm column
3007-31105
Graphite Vespel ®Ferrule for 0.25
mm column
3007-31108
Graphite Vespel ®Ferrule for 0.32
mm column
3007-31110
Graphite Vespel ®Ferrule for 0.53
mm column
17
18
PHASER Spare parts
Part number Description
2702-18506
Glass Nose Cone
Type Y
2702-18505
Glass Nose Cone
Type R
sge123730
SilFlow 4 Port Splitter 1.1mm Port
sge123704 SilFlow Nuts ,
sge123705 SilFlow Ferrules 1.1mm ID
sge123706 SilFlow Ferrules 0.4mm ID
sge123707 SilFlow Ferrules 0.5mm ID
sge123709 SilFlow Ferrules 0.7mm ID
sge123713 SilFlow Ferrules 0.35mm ID
sge123717 SilTite FingerTite Tool
sge123742 SilFlow Ferrules 0.8mm ID
sge123755 SilFlow SS capillary Tubing 1.1 mm
OD Sleeved to 1/16"
18
19
PHASER Spare parts
Part number Description
2702-18560 Spare Fuse 250 V T 3 A
5.2 x 20 mm
2702-18561 Spare Fuse 250 V T 5 A
5.2 x 20 mm,
3004-32231 PFA Tubing
3.18 mm O.D. x 1.58 mm I.D.
3004-50041 Sulfinert® Tubing
0.74 mm O.D. x 0.53 mm I.D.
1010-36132 Fused Silica Capillary Tubing
0.150 mm I.D. x 0.375 mm O.D.
1010-36222 Fused Silica Capillary Tubing
0.200 mm I.D. x 0.350 mm O.D.
1010-36322 Fused Silica Capillary Tubing
0.250 mm I.D. x 0.350 mm O.D.
1010-36452 Fused Silica Capillary Tubing
0.250 mm I.D. x 0.350 mm O.D.
1010-36682 Fused Silica Capillary Tubing
0.200 mm I.D. x 0.350 mm O.D.
19