compact controller for stand-by and parallel operating...
TRANSCRIPT
Compact Controller for Stand-by and Parallel Operating Gen-sets
Inteli New Technology Modular Gen-set Controller
IG-NT, IG-NTC, IG-NT-BB, IG-NTC-BB, IS-NT, IS-NTC-BB IM-NT
Software version IGS-NT-2.6, IM-NT-2.9 November 2011
INSTALLATION GUIDE
ComAp, spol. s r.o. Copyright © 2011 ComAp s.r.o. Kundratka 2359/17, 180 00 Praha 8, Czech Republic Written by Pavel Mareš Tel: +420 246 012 111, Fax: +420 246 316 647 Prague, Czech Republic E-mail: [email protected], www.comap.cz
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
2
Table of Contents Table of Contents .................................................................................................................................... 2 General Guidelines.................................................................................................................................. 6
What is described in this manual? ....................................................................................................... 6 WARNING............................................................................................................................................ 6
Remote control ................................................................................................................................. 6 Dangerous voltage............................................................................................................................... 6 Adjust set points................................................................................................................................... 6 Conformity declaration......................................................................................................................... 7 Symbols ............................................................................................................................................... 7 Text ...................................................................................................................................................... 7 Required and optional modules ........................................................................................................... 8
Dongle overview............................................................................................................................... 9 Available PC software ...................................................................................................................... 9
Marine Application Notes....................................................................................................................... 10 Safety requirements........................................................................................................................... 10
Power supply.................................................................................................................................. 11 Default configuration .......................................................................................................................... 12
Override function ............................................................................................................................ 12 Terminals and Dimensions.................................................................................................................... 13
Controller terminals and dimensions ................................................................................................. 13 IG-NT, IG-NTC, IM-NT ................................................................................................................... 13 IG-Display....................................................................................................................................... 14 IS-NT with IS-Display ..................................................................................................................... 14 IS-Display ....................................................................................................................................... 15 InteliVision 8 ................................................................................................................................... 16 IS-NT with InteliVision 8 ................................................................................................................. 16 IS-NT-BB ........................................................................................................................................ 17 InteliVision 5 ................................................................................................................................... 17 IG-NT-BB (IG-NTC-BB, IS-NTC-BB).............................................................................................. 18 IG-NT-BB with InteliVision 5........................................................................................................... 18
Front panels interface ........................................................................................................................ 19 InteliGen NT controller ................................................................................................................... 19 InteliMains NT controller................................................................................................................. 19 InteliSys NT controller .................................................................................................................... 20 InteliVision 5 ................................................................................................................................... 21 InteliVision 8 ................................................................................................................................... 22
Display Wiring .................................................................................................................................... 23 IG-Display wiring ............................................................................................................................ 23 IS-Display wiring............................................................................................................................. 23 InteliVision 5 ................................................................................................................................... 25 InteliVision 8 ................................................................................................................................... 26
Peripheral modules terminals and dimension.................................................................................... 30 IG-AVRi + IG-AVRi TRANS........................................................................................................... 30 IS-BIN16/8...................................................................................................................................... 31 IS-AIN8........................................................................................................................................... 32 IGL-RA15 Remote annunciator...................................................................................................... 32 IGS-PTM ........................................................................................................................................ 33 IG-IB Internet bridge....................................................................................................................... 34 I-LB Local Bridge............................................................................................................................ 35 I-CB Communication Bridge........................................................................................................... 35 I-RB16, I-RB16/231 relay board..................................................................................................... 36 I-CR CAN Repeater........................................................................................................................ 37 I-AOUT8 ......................................................................................................................................... 38
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
3
I-LBA............................................................................................................................................... 41 Recommended Wiring ........................................................................................................................... 42
IG-NT ................................................................................................................................................. 42 InteliGen – New Technology .......................................................................................................... 42 Interface ......................................................................................................................................... 43
IG-NTC............................................................................................................................................... 44 InteliGen – New Technology – Option C........................................................................................ 44 Interface ......................................................................................................................................... 45
IS-NT-BB............................................................................................................................................ 46 InteliSys – New Technology – Base Box ....................................................................................... 46 Interface ......................................................................................................................................... 47
IM-NT ................................................................................................................................................. 48 InteliMains – New Technology ....................................................................................................... 48 Interface ......................................................................................................................................... 49
IG-NT-BB ........................................................................................................................................... 50 InteliGen – New Technology – Base Box....................................................................................... 50 Interface ......................................................................................................................................... 51
IG-NTC-BB......................................................................................................................................... 52 InteliGen – New Technology - Option C – Base Box ..................................................................... 52 Interface ......................................................................................................................................... 53
IS-NTC-BB ......................................................................................................................................... 54 InteliSys – New Technology – Base Box ....................................................................................... 54
IS-NTC-BB Jumper Settings.............................................................................................................. 56 Wiring................................................................................................................................................. 58
General........................................................................................................................................... 58 Power supply.................................................................................................................................. 58 Power supply fusing ....................................................................................................................... 58 Grounding....................................................................................................................................... 59 Magnetic pick-up ............................................................................................................................ 59
Voltage measurement........................................................................................................................ 61 Voltage measurement separation .................................................................................................. 61 IG MTU........................................................................................................................................... 62
Current measurement ........................................................................................................................ 62 Earth fault protection ...................................................................................................................... 63 Recommended wiring IG-NT – SPTM application ......................................................................... 65 Recommended wiring IG-NT – SPI application ............................................................................. 66 Recommended wiring IG-NT – MINT application .......................................................................... 67
Single phase applications .................................................................................................................. 68 Recommended wiring..................................................................................................................... 68
Controller Binary inputs and outputs.................................................................................................. 69 Binary output via I-RB16 ................................................................................................................ 69 Wiring example 1............................................................................................................................ 69 Wiring example 2............................................................................................................................ 70 Wiring example 3............................................................................................................................ 70 Wiring example 4............................................................................................................................ 71
Binary inputs on IS-BIN16/8 .............................................................................................................. 73 Binary outputs on IS-BIN16/8 ............................................................................................................ 73
Binary output protections ............................................................................................................... 73 Dongle installation.............................................................................................................................. 74
IS-NT Jumpers ............................................................................................................................... 75 Analog input jumpers...................................................................................................................... 75 Speed governor output jumper....................................................................................................... 75
Analog output jumper......................................................................................................................... 76 Analog inputs wiring examples .......................................................................................................... 77
Resistive sensors (two wires)......................................................................................................... 77 Resistive sensors (one wire) .......................................................................................................... 77 Current sensors.............................................................................................................................. 78 Current and resistive sensors ........................................................................................................ 78
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
4
Voltage and resistive sensors ........................................................................................................ 79 Tristate sensors.............................................................................................................................. 80
Analog inputs on IS-AIN8................................................................................................................... 81 External modules connection............................................................................................................. 82
IS-AIN8, IS-BIN8/16 address setting.............................................................................................. 83 IS-AIN8, IS-BIN8/16 SW version check ......................................................................................... 83 IGS-PTM and IGL-RA15 module connection................................................................................. 84 Connection of ECU on CAN1......................................................................................................... 85 CAN bus Tx, Rx LED indication ..................................................................................................... 85
I-CB wiring and configuration............................................................................................................. 85 Recommended CAN/RS485 connection ........................................................................................... 86
CAN bus connection....................................................................................................................... 86 RS485 connection .......................................................................................................................... 86
Default Sensors ..................................................................................................................................... 88 Default characteristics........................................................................................................................ 88
Controller ........................................................................................................................................ 88 Tristate sensor................................................................................................................................ 88 IS-AIN8........................................................................................................................................... 88
Sensor fail detection (FLS) ................................................................................................................ 90 Speed Governor Interface List .............................................................................................................. 91
Electronic engines interface............................................................................................................... 91 Communication Bridge Unit ........................................................................................................... 91
Speed governor interface................................................................................................................... 91 Controller Speed reg out voltage limits .......................................................................................... 91
AVR Interface List.................................................................................................................................. 98 Technical Data..................................................................................................................................... 107
Power supply ................................................................................................................................... 107 Operating conditions ........................................................................................................................ 107 Dimensions and weight.................................................................................................................... 108 Mains and generator ........................................................................................................................ 108
Current inputs............................................................................................................................... 108 Voltage inputs – IG/IS-NT and modifications ............................................................................... 108
Binary inputs and outputs ................................................................................................................ 108 Binary inputs................................................................................................................................. 108 Binary open collector outputs....................................................................................................... 109
Analog inputs ................................................................................................................................... 109 D+ function....................................................................................................................................... 109 Speed pick-up input ......................................................................................................................... 109 Communication interface ................................................................................................................. 109
RS232 interface............................................................................................................................ 109 RS485 interface............................................................................................................................ 109 CAN bus interface ........................................................................................................................ 109
Analog outputs ................................................................................................................................. 110 IG-AVRi............................................................................................................................................ 110
IG-AVRi Trans/LV......................................................................................................................... 110 IG-AVRi Trans/100....................................................................................................................... 110
IGS-PTM .......................................................................................................................................... 111 Binary inputs................................................................................................................................. 111 Binary open collector outputs....................................................................................................... 111 Analog inputs................................................................................................................................ 111 Analog output ............................................................................................................................... 111
IS-AIN8............................................................................................................................................. 111 Analog inputs................................................................................................................................ 112
I-AOUT8........................................................................................................................................... 112 IS-BIN16/8 ....................................................................................................................................... 112
Binary inputs................................................................................................................................. 113 Open collector outputs ................................................................................................................. 113 Frequency inputs.......................................................................................................................... 113
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
5
IGL-RA15 ......................................................................................................................................... 113 Power supply................................................................................................................................ 113 Operating conditions .................................................................................................................... 113 Dimensions and weight ................................................................................................................ 113 Horn output................................................................................................................................... 114
I-CB, I-CR ........................................................................................................................................ 114 Power supply................................................................................................................................ 114 Operating conditions .................................................................................................................... 114 Dimensions and weight ................................................................................................................ 114 CAN bus interface ........................................................................................................................ 114 RS232 interface............................................................................................................................ 114
I-LB................................................................................................................................................... 114 IG-IB................................................................................................................................................. 114 I-RBxx .............................................................................................................................................. 115 IG-MTU ............................................................................................................................................ 115 IG-MTU-2-1...................................................................................................................................... 115
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
6
General Guidelines
What is described in this manual?
IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTION - This manual contains important instructions for IGS-NT controllers family that shall be followed during installation and maintenance of the Inteli NT genset controllers. It is intended for use by Gen-set control panel builders and for everybody who is concerned with installation, operation and maintenance of the gen-set.
WARNING
Remote control The controller can be remotely controlled. In the event that maintenance needs to be done to the gen-set, check the following to ensure that the engine cannot be started. To be sure:
Disconnect remote control via RS232 or another communication line Disconnect input REMOTE START/STOP
or Disconnect output STARTER and outputs GCB CLOSE/OPEN and MCB CLOSE/OPEN.
Be aware the unqualified manipulation can disconnect the object from the power supply source. The controller contains a large number of configurable setpoints, because of this it is impossible to describe all applications. Controller functions are subject to change from SW version to SW version. This manual only describes the product and is not guaranteed to be set for your application on arrival.
!!! CAUTION !!! Dangerous voltage The terminals for voltage and current measurement should never be touched. Properly connect the grounding terminals. Do not disconnect the Controller CT terminals for any reason.
Adjust set points All parameters are djusted to their typical values. But the set points in the “Basic settings” settings group !!must!! be adjusted before the first startup of the gen-set.
!!! WRONG ADJUSTMENT OF BASIC PARAMETERS CAN DESTROY THE GEN-SET !!!
The following instructions are for qualified personnel only. To avoid personal injury do not perform any action not specified in this User guide !!!
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
7
WARNING – VERY IMPORTANT !!! Be aware that the binary outputs can change state during and after software reprogramming. Before the controller is used again ensure that the proper configuration and setpoint settings
are set in the controller. Every time you want to disconnect following controller terminals:
• Mains voltage measuring and / or • Binary output for MCB control and / or • MCB feedback
Be aware that the MCB can be switched off and gen-set can start !!!
Switch controller to MAN mode and disconnect the Binary outputs Starter and Fuel or press EMERGENCY STOP button to avoid unexpected automatic start of gen-set and GCB closing during
any work or maintenance on the gen-set or switchboard.
Conformity declaration
Following described machine complies with the appropriate basic safety and health requirement of the EC Low Voltage Directive No: 73/23 / EEC and EC Electromagnetic Compatibility Directive 89/336 / EEC based on its design and type, as brought into circulation by us.
CAUTION! Use the device according to instruction in manual only to ensure the protection provided by this device. This protection can be affected by using of the device any other way.
Symbols Symbols used in this manual:
Grounding point symbol
AC voltage symbol
DC voltage symbol
Text PAGE (Capital letters in the frame) buttons on the front panel
Break Return (Italic) set points Generator protections Set point group Note: ComAp believes that all information provided herein is correct and reliable and reserves the right to update at any time. ComAp does not assume any responsibility for its use unless otherwise expressly undertaken.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
8
Required and optional modules
Controller Description Standard / Optional
IG-NT IG-NTC IM-NT
Controller Central Units with internal display
Standard
IS-NT-BB IG-NT-BB IG-NTC-BB IS-NTC-BB
Controller Central Unit without internal display Standard
Accessories and modules Description Standard /
Optional IG-Display Additional display for IG-NT/NTC/EE/EEC, IM-NT Optional IS-Display Additional display for IS-NT-BB Optional InteliVision 5 Additional colour display for IS-NT-BB, IG-
NT/NTC/EE/EEC, IM-NT, IS-NTC-BB, IG-NT-BB, IG-NTC-BB
Optional
InteliVision 8 Additional colour display for for IS-NT-BB, IG-NT/NTC/EE/EEC, IM-NT, IS-NTC-BB, IG-NT-BB, IG-NTC-BB
Optional
IG-AVRI Controller AVR interface Optional IG-AVRi-TRANS/LV IG-AVRi-TRANS/100
Voltage transformer for supplying AVRi module Optional
AT LINK-CABLE 1,8m
RS232 (InteliMonitor, GenConfig) communication cable (It is not a part of controller delivery.)
Optional
IS-AIN8 External analog inputs unit Optional IS-BIN16/8 External binary I/O unit Optional I-LB+ Replaces IG-MU and I-LB (RS232/RS485
communication speed increased to 57600 bps); communication with multiple controllers to a local PC.
Optional
IG-IB Internet bridge Optional I-CB/CAT-Gas I-CB/CAT-Diesel I-CB/MTU I-CB/MTU-SIAM4000 I-CB/DeutzTEMe
Inteli - Communication Bridge: Interface unit for some types of engines with ECU (without J1939)
Optional
IGL-RA15 Remote annunciator Optional IGS-PTM External analog, binary I/O unit Optional I-AOUT8 8 analog outputs unit Optional IG-MTU Voltage transformer unit to separate mains and
generator voltage measurement Optional
IG-MTU-2-1 Voltage transformer unit with voltage ratio 2:1 to separate mains and generator voltage measurement
Optional
Controller central unit contains complete hardware for all applications. Number of inputs and outputs can be expanded by additional modules IS-AIN8, IS-BIN16/8, IGS-PTM, IGL-RA15, I-AOUT8.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
9
Dongle overview Dongle Function No dongle for Single parallel to mains is required. IGS-NT-LSM+PMS Dongle for multiple applications MINT with Load sharing, Var sharing
and Power management function IGS-NT-SUS-LSM+PMS
Dongle for multiple application SUS MINT with Load sharing, Var sharing and Power management function
IGS-NT-SUS-PCM Dongle for SUS application See chapter Dongle installation to learn how to place the dongle into the controller.
Available PC software Name Function GenConfig Common IGS-NT family configuration (off-line) tool. InteliMonitor Common IGS-NT family monitoring (on-line) tool. WinScope Graphic monitoring-recording tool. IGS-Log Common IGS-NT family logging PC SW. IBConfig Internet Bridge configuration tool. Gm_setup GSM modem setup tool. ICBEdit I-CB configuration tool. Hint: For more information about controllers and modules (number of I/O, communication ports, …) see IGS-NT-x.y-Application guide.pdf.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
10
Marine Application Notes The IGS-NT system and components can be used as Control, Monitoring and Protection for single and multiple generator applications according to Marine Type Approval Regulation Controller is tested and approved:
- For location in Machinery spaces and Control room – Location class B. - According the EMC rules for general power distribution zones.
Safety requirements Additional, independent safety and protection devices are necessary to meet safety requirements of Rules and Regulations of Marine Classification Societies. The sensors and circuits utilized for the second stage alarm and automatic shutdown are to be independent of those required for the first stage alarm (LR Rulefinder 2008 - V9.10). The project designer is responsible to follow Marine regulations in project design wiring and InteliGen-NT or InteliSys-NT controller configuration and setpoint setting. Usually is necessary to use additional, independent equipment for Emergency stop, Overspeed, Low oil pressure and Overcurrent protection. Oil mist and engine bearing temperature monitoring are to be provided when arrangements are fitted to override the automatic shutdown for excessive reduction of the lubrication oil pressure (or for engines above 2250 kW). The Overriding of this protection is to be independent. Required alarms and safeguards for auxiliary engines.
Lubrication oil inlet temperature high Lubrication oil inlet pressure low Coolant outlet temperature high Coolant pressure or flow low Exhaust gas temperature high
The maximal wire length for Binary (Analog) inputs and outputs should be less than 10 meters, otherwise the separation relay or additional protection has to be used.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
11
+24V
DC
0 V
DC
BO 1
BO
2
BO
3
BO
4
BO
5
BO 6
BO
7
BO 8
BO 9
BO
10
BO
12
BO
13
BO
14
BO
15
BO
16
BO
11
+PW
R B
OU
T
+PW
R B
OU
T
BI 1
BI 2
BI 3
BI 4
BI 5
BI 6
BI 7
BI 8
BI 9
BI 1
0
BI 1
2
BI 1
3
BI 1
4
BI 1
5
BI 1
6
BI 1
1
+ -
IS-NT (IG-NT)
I-RB16 ( I-RB8 )
K17 K18
Max wire length < 10m
Max wire length < 10m
1 2 3
In the case of longer distance wires the additional protection has to be used for Signal inputs and Outputs close to controller terminals. Protection is available on request in ComAp.
1N40
07
3x
14D
K39
0
33M
/50
14D
K22
0
14D
K39
0
14D
K39
0
Power supply To have full Surge protection ±2kV for controller power supply terminals the external component (e.g. two DK4/35 U S14 K60 from Weidmueller for DIN rail) has to be connected.
+24VB from battery
-24VB from battery
IG-NT or IS-NT controller
Controller box shielding
+24VB
0VB
The I-LBA (low battery adaptor) module is to be used when power supply voltage dip up to 200ms is required. The up to 100ms supply voltage dip is acceptable by IG-NT or IS-NT controller itself.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
12
IS-NT (IG-NT)
- +Controller box shielding
Default configuration Use the default IG-MINT-Marine-2.3.ant or IS-MINT-Marine-2.3.ant (or higher) to avoid incorrect system setting and configuration. Default configuration can be modified using the GenConfig-2.3 (or higher) PC tool. Please take care of following items that are included in default configuration file: - The function "Virtual Peripheries" shall not be used for marine application. - An automatic start of the generator after acknowledgement of alarm shall be prevented (Basic settings: FltResGoToMAN = ENABLED). - Common alarm contacts interfacing the machinery alarm system shall be re-triggered in case of occurring new alarm" (BO5 = Alarm flashing).
Override function The “Sd override” (Shut-down override) function is included in default configuration on Binary input BI7. Active Override is indicated by a " ! " mark on the display and on Binary output BO4 Common SdOvr. The default Override function blocks all protections except the Overspeed, Emergency stop and all Analog or Binary protections configured as SD Override. It is strongly recommended to modify names of such values to begin or finish with letters SDO – e.g. WaterTemp SDO. Use internal PLC function when the independent override protection e.g. for Bearing temperature is required.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
13
Terminals and Dimensions
Controller terminals and dimensions
IG-NT, IG-NTC, IM-NT
170 (6,7")
185 (7,3")
123
(4,8
“) RS
232
USB
68
2,7
“
Cutout for IG-XX/IM-NT113 x 175 mm
4,4 x 6,9”
123
(4,8
“)
110
(4,3
“)
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
14
IG-Display
170 (6,7")
185 (7,3")
Cutout for IG-DISPLAY113 x 175 mm
4,4 x 6,9”
123
(4,8
“)
110
(4,3
“)
IS-NT with IS-Display
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
15
IS-Display
30
1,2“
176
(6,9
“)
290 (114,2")
280 (11")
184
(72,
44“)
Cutout for IS-DISPLAY178 x 2827,0 x 11,1”
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
16
InteliVision 8
IS-NT with InteliVision 8
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
17
IS-NT-BB
170 (6,7")
194 (7,6")
123
(4,8
“) RS
232
USB
68
2,7
“
110
(4,3
“)
184 (7,3")
90 (3
,6")
4x o 4,3 35 (1,4") 2x M3
68 (2,7“)
194 (7,6")
Hint: In the environment rich on vibrations it is not recommended to fix IS-NT-BB on the DIN rail but to screw it down on to the switchboard rear side.
InteliVision 5
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
18
IG-NT-BB (IG-NTC-BB, IS-NTC-BB)
IG-NT-BB with InteliVision 5
RS
232
114
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
19
Front panels interface
InteliGen NT controller InteliGen controller types IG-NT, IG-NTC InteliGen – Remote Display IG-DISPLAY Available for applications SPI, SPTM, MINT, COX, CombiI
InteliMains NT controller InteliMains controller types IM-NT InteliMains – Remote Display IG-DISPLAY Available for applications MCB, MGCB, BTB
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
20
InteliSys NT controller InteliSys controller types IS-NT InteliSys – Remote Display IS-DISPLAY Available for applications SPI, SPTM, MINT, COX, Combi
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
21
InteliVision 5 Colour detachable display. Available for units: Unit Number of displays Display address IG-NT(C) –BB 2 1 and 2 IS-NTC – BB 3 1, 2, 3 IM-NT-BB 2 1 and 2 IG-NT(C) 1 2 IS-NT-BB 3 1, 2 ,3 IM-NT 1 2
Hint: Display is connected via RS-485 only! Use the RS485 socket which is dedicated for communication with displays.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
22
InteliVision 8 Colour detachable display.available for all InteliGen, InteliSys and InteliMains controllers. Connection type: CAN2, RS 485, RS 232.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
23
Display Wiring
IG-Display wiring IG-NT IG- DISPLAY
IS-D
ISP A1
COMR1B1
RS485Wire length: up to 1000 meters
IG-D
ISPL
AY
A1COMR1B1
POW
ER
8-36 VDC
0 VDC
POW
ER
0 VDC
RS2
32
MODEM / GSM
GenConfigInteliMonitor
BI: Alternative brightness
A1COMR1
B1
IG-N
T
8-36 VDC
IS-Display wiring
IS-N
T-B
B
IS-D
ISPL
AY
IS-NT
RS485Wire length: up to 1000 meters
IS-DISPLAYIS
-DIS
PLA
Y
IS-D
ISP
A1COMR1
B1
IS-N
T-B
B
A1COMR1B1
POW
ER
POW
ER
A1COMR1
B1
0 VDC
POW
ER
8-36 VDC
0 VDCBI: Alternative brightness
8-36 VDC
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
24
IS-DISPLAYIS-NT-BB
IS-D
ISP A 1
COMR1B 1
IS-N
T-B
B
RS485Wire length: up to 1000 meters
IS-N
T-B
B
A1COMR1B1
IS-D
ISPL
AY
POW
ER
8-36 VDC
0 VDC
POW
ER
0 VDC
USB
RS2
32U
SB
MODEM / GSM
GenConfigInteliMonitor
BI:Alternative brightness
A1COMR1
B1
8-36 VDC
IS-NT- BB
IS-D
ISP A1
COMR1B1
IS- DISPLAY
IS-N
T-B
B
RS485Wire length: up to 1000 meters
POW
ER
0 VDC
USB
RS2
32U
SB
MODEM / GSM
GenConfigInteliMonitor
POW
ER
8-36 VDC
0 VDC
IS-D
ISPL
A Y
A1COMR1B1
IS-D
ISPL
AY
IS-D
ISPL
AY
8-36 VDC
BI:Alternative brightness
Hint: The state of BI Alternative brightness only influences the particular display. IS-NT-BB unit doesn’t include internal display. For IG/IS-NT hardware options consult IGS-NT-x.y-Application guide.pdf.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
25
InteliVision 5
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
26
InteliVision 8 How to connect InteliVision8 with IG-NT?
Hint: Only one external display could be connecter to the control unit via RS485.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
27
How to connect InteliVision8 with G-NT-BB?
IG-NT-BBR
S232 (1)
DISPLAY CAN1 CAN2
ABC
OM HL
CO
M HLC
OM
InteliVision 8
PC
Modbusterminal
Modem
OR
OR
OR
IG-Display InteliVision 5 InteliVision 8
I-LB+ / IG-IB/InteliVision 8
Local address 1
I-LB+ / IG-IB/InteliVision 8
Local address 2
I-LB+ / IG-IB/InteliVision 8
Modem address 1
I-LB+ / IG-IB/InteliVision 8
Modem address 2
PC PC Modem Modem
OR/AND* OR/AND*
Intercontroller CAN2RS4
85te
rmin
al
RS
232
Hint: Two displays could be connected to the IG-NT-BB control unit via RS485 (display terminal) with addresses 1 and 2.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
28
How to connect InteliVision8 with IS-NT-BB?
Hint: Up to three displays could be connected with IS-NTC-BB via RS 485(1).
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
29
How to connect InteliVision 8 with IS-NTC-BB?
Hint: Up to three displays could be connected with IS-NTC-BB via RS 485(1).
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
30
Peripheral modules terminals and dimension
IG-AVRi + IG-AVRi TRANS
AVRi
-
AVRi
+
OUT1
OUT2 AC
1AC
2
OCOM
LB 5
Primary terminals 230-277 VAC / 400-480 VAC
0 - 18
43 (1,7”) 43 (1,7”)
36(1
,4”)
0 - 230/277 - 400/480
IG-AVRiTRANS/LV
Secondary terminals 18 VAC
IG-AVRi unit is DIN rail mount (35mm) IG-AVRi TRANS are DIN rail mount (35mm)
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
31
IS-BIN16/8 45 (1,8")146 (5,7")
160
(6,3
") 40 (1,6")
25 (1,0")
IN1
-
RPM
+
IN 2
IN1
+
RPM
-
IS-BIN16/8 unit is DIN railmount (35mm)
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
32
IS-AIN8 46, 4 (18,3")
40 (15,7")
25 (9,8")
70 (27,5")
146 (57,5")
160
(63"
)
POWER8 - 36V DC
CO
M
CAN 1
H L
+
iS-AIN8
IS-AIN8 unit is DIN rail mount (35mm)
IGL-RA15 Remote annunciator Remote (CAN bus, up to 200 meters) 15 LED states indicator. IGL-RA15 unit can be connected to controller via CAN as Binary output group with addresses 1+2 or 3+4 or 5+6 or 7+8. To configure IGL-RA15 use GenConfig -> Modules -> Available modules, select IGL-RA15 module and add it using + button. GenConfig automatically adds IGL-RA15 binary outputs to the configuration. For more information about IGL-RA15 consult manual (IGL-RA15-1.2.pdf) and New features list (IGL-RA15-2.0-New features.pdf).
InteliGenNT, InteliGenNT-B , InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
33
165 (6,5”)
38(1
,5”)
40(1
,6”)~75
(3,0
”)
~35
(1,4
”)
180 (7,1”)185 (7,3”)
106
(4,2
”)
44 (1,7”)54 (2,1”)
~25
(1,0
”)
120
(4,7
”)12
5(4
,9”)
Cutoutfor Remote Annunciator
167 x 108 mm(6,6 x 4,3)”
IGS-PTM IGS-PTM is I/O extension module with 8 binary I/O, four analog inputs configurable for range:
• 0 – 250 Ω (suitable for Pt100, Ni100, VDO pressure, VDO level), • 0 – 100 mV (suitable for thermocouples), • 0 – 20 mA.
and one analog output configurable for range • 0 to 20 mA.
Detail descriptions see in IGS-PTM-7.0.pdf manual. Hint: The 0-100 mV inputs are only suitable for thermocouples electrical separated from the frame – “isolated” type. For non-isolated type thermocouples use IS-AIN8 module. The 0-250Ω input is not possible to use for Pt1000, Ni1000 and VDO Temp sensors due to measurement range < 250Ω. For operation with IGS-NT controller it is necessary to close IGS jumper.
B, InteliGenNTC-BB, InteliSysNT
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
34
95 mm(3,7´´)
43 mm(1,7´´)
96 m
m (3
,8´´)COMPENSATION
GND
POWER
8-36V DC
BINARY OUTPUTS
BINARY INPUTS ANALOG INPUTS
AI4
BI8
BI7
BI6
BI5
BI4
BI3
BI2
BI1
0-20 mA ANALOG OUT
BO8
BO1
BO2
BO3
BO4
BO5
BO6
BO7
CAN
RxTx
CAN
LH
COM
LB 4
AO-
AO+
iGS-PTM
IGS-PTM unit is DIN rail (35mm) mounted.
IG-IB Internet bridge
95 mm(3,7´´)
43 mm(1,7´´)
96 m
m (3
,8´´
)
See InteliCommunicationGuide for further information. It is recommended to use IG-IB firmware version 2.0. IG-IB unit is DIN 35 mm rail mounted.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
35
I-LB Local Bridge I-LB+ is a successor of the IG-MU and I-LB units designed to be used with IG/IS-NT controllers. It therefore provides additional communication port and higher communication speed. Speed for direct/modem connection can be up to 57600 bps (IG-MU only 19200 bps). There are two versions of I-LB: Name Description Dimensions and terminals I-LB+ with USB
port (speed ≈ 115200 bps)
95 mm(3,7´´)
43 mm(1,7´´)
96 m
m (3
,8´´)
D1D2P1P2P3P4P5P6
P7120
120 RxD
TxD
RxC
TxC
Tx
Rx
Indication LED: TxC, RxC Indicates data transfer on the CAN line. TxD, RxD Indicates data transfer on the RS232 line. Tx, Rx Indicates data transfer on USB RUN Lights when at least one other unit is active on the CAN bus.
Blinks when no unit is communicated on the CAN bus (during communication speed detection).
PWR Lights All the time when power supply is switched on.
I-CB Communication Bridge
POWER8-36V DC
COM
RS 23
2
LB 4i-CB
95 mm(3,7´´)
43 mm(1,7´´)
96 m
m (3
,8´´)
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
36
I-CB (Communication bridge) is CAN bus interface between Controller and Engine Control Unit (ECU) that has not standard J1939 communication (MTU, CAT etc.). Engine values (RPM, Oil pressure and other) are received from ECU via CAN and corresponding sensors are not needed on controller. Use ICBEdit software for I-CB configuration (included in installation package).
I-RB16, I-RB16/231 relay board Relay board contains 16 relays for binary (open collector) output separation. All relays are placed in sockets. Number relays: 16 in socket Nominal voltage: 24 VDC Voltage range: 16,8 – 36 VDC Relay opens at: 10% of nominal voltage Electric / mechanic cycles: 100 000 (when switching 16A) / 10 000 000 Operating temperature range: - 40°C to 70°C Maximal load: 16A resistive load 4A inductive load Contacts protection: varistor 14DK390 Relay-connector connection:
1 – 2 n.o. 1 – 3 n.c.
1K
2 3
I-RB16/231 board contains relays that can switch 231 VAC load.
Mechanical dimension I-RB16 is 35 mm DIN rail mounted. One unit contains two parts (separate PCB) 8 relays each on common plastic base. I-RB16 is 60mm high from DIN rail base.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
37
16X17
11 1 11 1 11
1 +X18
11 1 11 1 11
RE1
RE2
RE3
ER4
RE5
RE6
RE7
RE8
RE9
RE10
RE11
ER12
RE13
RE14
RE15
RE16
X3 X1X2X6 X4X5X8 X7X11 X9X10X14 X12X13X16 X15
9 + 8
16 X18 9 +View B
X18
8 X17 1 +
View B
3 X1 1
X1 X2 X3 X4 X5 X6 X7 X8 X9 X10 X11 X12 X13 X14 X15 X16
View A
3 X2 1 3 X3 1 3 X4 1 3 X5 1 3 X6 1 3 X7 1 3 X8 1 3 X9 1 3 X10 1 3 X11 1 3 X12 1 3 X13 1 3 X14 1 3 X15 1 3 X16 1
View A300
95
X17
Hint: I-RB contains two separate boards, 8 relay each. It can be ordered as I-RB8 as well.
I-CR CAN Repeater I-CR module enables to extend CAN bus line of
- extension modules CAN1 to more than 200 meters - intercontroller CAN2 to more than 200/900 meters (in 32C/8C mode)
More application details see in separate manual “Extending the CAN bus”.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
38
95 mm(3,7´´)
43 mm(1,7´´)
96 m
m (3
,8´´
)
I-AOUT8 I-AOUT8 is a new extension unit with 8 analog outputs. Each analog output can be switched by jumper for.
- 0 to 20 mA - 0 to 10 VDC - PWM (Pulse With Modulation on 1,2 kHz)
I-AOUT8 module is connected on IGS-NT CAN1 (peripheral) bus. The corresponding module Address 1 to 4 (default 1) must be set on module (by Adr.1 and Adr.2 jumpers) and in controller configuration. Communication fail is indicated in controller Alarm list and by binary output. Use GenConfig PC tool for controller configuration.
It is possible to connect up to four I-AOUT8 units to one controller. Unit is 35 mm DIN rail mounted. CAN1 terminating 120 ohm resistor jumper is connected in default. AGND terminals are on the same potential.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
39
95 mm (3,7´)43 mm(1,7´)
Powersupply
I-AOUT8ComApHW:SW:
ANALOG OUTPUTS
ANALOG OUTPUTS
CAN
U - I - p U - I - p U - I - p U - I - p
p - I - U p - I - U p - I - U p - I - U
1 2 Pwr
120 ohm
Functions Number of analog outputs 8, no galvanic separation Type of analog outputs (jumper selectable)
U I p
0 to 10VDC ± 1% , max 5 mA 0 to 20 mA ± 1% , max 500 ohms pwm 1200 Hz, 5V level, max 10 mA
Power supply 8 to 36 VDC Current consumption 100 ÷ 300 mA at 24 VDC Communication interface CAN1, with jumper selectable address 1 to 4
Jumper selectable terminating resistor 120 ohms. RS232 interface TTL, firmware upgrade via AT-link. Operating temperature range -40°C to +70°C Analog outputs refreshment Max. 300 ms
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
40
CAN address jumper setting Up to four modules can be connected to one controller. Set module CAN address corresponding to configuration according table below.
CAN Address Jumper 1 Jumper 21 No No 2 Yes No 3 No Yes 4 Yes Yes
Analog output hardware modification Follow the p-I-I-U symbols on the module sticker. There are two equivalent positions for mA measuring.
AOUT jumper Symbol Function
p Pwm Pulse-Width-Modulation
I 0 to 20 mA
U 0 to 10 VDC
LED indication Green LED is located near the power supply connector.
I-AOUT8 module state LED Pwr No power supply Dark Memory fail Fast blink (100/100 ms) Communication fail Slow blink (300/300 ms) OK Continuous light
Wiring and jumper setting example Voltage output 0 to 10 VDC Current output 0 to 20 mA Current output 0 to 20 mA Pwm output
5V, max 10 mA
AGND
AOUT
AGND
AOUT
max 500ohm
+
+
+
max 5 mA+
AGND
AOUT
max 500ohm
AGND
AOUT
Pwm output 1200 Hz Current output 0 to 20 mA Current output 0 to 20 mA Voltage output 0 to 10 VDC
Hint: Extension module communication fail can be configured in GenConfig to No protection, Warning, Shutdown.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
41
I-LBA For the connections with 12VDC power supply an I-LBA module can be connected to controller power terminals in order to allow the controller to continue operation during cranking if the battery voltage dip occurs. Controllers which may be supplied from I-LBA module: Controller IG-NT/
IG-NT-BB IG-NTC/
IG-NTC-BB IS-BB/
IS-NTC-BB IS-NT IG-CU IS-CU IL-CU/
IL-NT Connection applicable
YES YES YES NO YES NO YES
AVRi
-
AVRi
+
OUT1
OUT2 AC
1AC
2
OCOM
LB 5
Hint: The I-LBA unit is intended to supply one controller unit only at the same time. It is not recommended to use +PWR BOUT outputs on thecontroller as a source for relays, as their consumption would exhaust I-LBA capacitors very fast. It is also not recommended to supply any kind of above controllers with LT (Low Temperature) display because of the high current consumption of the LT display. See also chapter Power supply fusing.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
42
Recommended Wiring
IG-NT Side label
InteliGen – New Technology
Side connectors
Back connectors
RS485 bias resistor jumpers
120 Ω Jumper
Boot JUMPER (with long holder)
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
43
Interface Function Terminals Note Generator voltage L1,L2,L3, (N) 3x 277 Ph-N or 480 Ph-Ph VAC
(neutral not needed), max 350 / 600VAC *, CAT III Mains/Bus voltage L1,L2,L3, (N) 3x 277 Ph-N or 480 Ph-Ph VAC
(neutral not needed), max 350 / 600VAC, CAT III Generator current L1k,L1l, L2k,L2l,
L3k,L3l 0 ÷ 5 Amps, max 10 A all time, 150 A for 2 sec
Neutral/Mains current LNk,LNl 0 ÷ 5 Amps, max 10 A all time, 150 A for 2 sec IG-AVRi interface AVRI-OUT, AVRI-COM TTL (5V PWM) interface to IG-AVRi Power supply + , - 8 ÷ 36 VDC D+ D plus Inputs and outputs Binary inputs BI1 ÷ BI6
BI7 ÷ BI12 Activation to minus power supply.
Binary outputs BO1 ÷ BO6 BO7 ÷ BO12
Load is connected to plus power supply.
Analog inputs AI1 ÷ AI3 Ohms, mA, Volts sensors Analog outputs SG-OUT, SG-COM Speed governor output interface (±10V / 5V PWM;
500 – 3000Hz) RPM RPM-IN, RPM-COM Min 2 Vpk-pk (from 4 Hz to 4 kHz) Communication interface RS232 (1) D SUB9 (male) PC: InteliMonitor, GenConfig or
Modem, GSM modem or ECU (e.g. Cummins ModBus) or InteliVision 8
RS232 (2) None RS485 (1) ** A1,B1,COMR1 IG-Display (Remote display) or InteliVision 8
(remote display) or for PC (via RS485 converter) = redirected RS232 (1) see Basic settings: RS485(1)conv. For IG-Display and InteliVision 8, the setpoint RS485 (1) conv has to be set to DISABLED value.
RS485 (2) None CAN1 L1,H1,COMC1 Extension modules: IS-AIN, IS-BIN,IGS-PTM, IGL-
RA15, I-AOUT CAN2 L2,H2,CONC2 Intercontroller (Load&VAR sharing, Power
management) and monitoring (IG-IB, I-LB) and up to 4 InteliVision 8 displays
Hint: * IG-MTU or IG-MTU-2-1 can be used for three wire systems, systems with separated Neutral or when galvanic separation between generator or mains voltage and controller is required. ** When more devices connected to RS485 bias resistor jumpers should be closed only on one of them.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
44
IG-NTC
InteliGen – New Technology – Option C
US
B
Boot JUMPER (with long holder)
120 Ω Jumper
RS485 bias resistor jumpers
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
45
Interface Function Terminals Note Generator voltage L1,L2,L3, (N) 3x120 / 277 Ph-N or 208 / 480 Ph-Ph VAC
(neutral not needed), max 350 / 600VAC *, CAT III Mains/Bus voltage L1,L2,L3, (N) 3x120 / 277 Ph-N or 208 / 480 Ph-Ph VAC
(neutral not needed), max 350 / 600VAC, CAT III Generator current L1k,L1l, L2k,L2l,
L3k,L3l 0 ÷ 5 Amps, max 10 A all time, 150 A for 2 sec 0 ÷ 1 Amp, max 2 Amps all time
Neutral/Mains current LNk,LNl 0 ÷ 5 Amps, max 10 A all time, 150 A for 2 sec 0 ÷ 1 Amp, max 2 Amps all time
IG-AVRi interface AVRI-OUT, AVRI-COM TTL (5V PWM) interface to IG-AVRi Power supply + , - 8 ÷ 36 VDC D+ D plus Inputs and outputs Binary inputs BI1 ÷ BI6
BI7 ÷ BI12 Activation to minus power supply.
Binary outputs BO1 ÷ BO6 BO7 ÷ BO12
Load is connected to plus power supply.
Analog inputs AI1 ÷ AI3 Ohms, mA, Volts sensors Analog outputs SG-OUT, SG-COM Speed governor output interface (±10V / 5V PWM;
500 – 3000Hz) RPM RPM-IN, RPM-COM Min 2 Vpk-pk (from 4 Hz to 4 kHz) Communication interface RS232 (1) D SUB9 (male) PC: InteliMonitor, GenConfig or
Modem, GSM modem or ECU (e.g. Cummins ModBus) or InteliVision 8
RS232 (2) D SUB9 (male) PC: InteliMonitor, GenConfig or Modem, GSM modem or InteliVision 8
RS485 (1) ** non isolated
A1,B1,COMR1 IG-Display (Remote display) or InteliVision 8 (remote display) or for PC (via RS485 converter) = redirected RS232 (1) see Basic settings: RS485(1)conv. For IG-Display and InteliVision 8, the setpoint RS485 (1) conv has to be set to DISABLED value.
RS485 (2) ** isolated
A2,B2,COMR2 Redirected RS232 (2) - see Basic settings: RS485(2)conv. PC: InteliMonitor, GenConfig or Modem, GSM modem or InteliVision 8
USB 2.0 slave PC: InteliMonitor, GenConfig CAN1 L1,H1,COMC1 Extension modules: IS-AIN, IS-BIN,IGS-PTM, IGL-
RA15, I-AOUT CAN2 L2,H2,CONC2 Intercontroller (Load&VAR sharing, Power
management) and monitoring (IG-IB, I-LB) and up to 4 InteliVision 8 displays
Hint: * IG-MTU or IG-MTU-2-1 can be used for three wire systems, systems with separated Neutral or when galvanic separation between generator or mains voltage and controller is required. ** When more devices connected to RS485 bias resistor jumpers should be closed only on one of them.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
46
IS-NT-BB
InteliSys – New Technology – Base Box
Boot JUMPER (with long holder)
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
47
Interface Function Terminals Note Generator voltage L1,L2,L3, (N) 3x120 / 277 Ph-N or 208 / 480 Ph-Ph VAC, CAT III
(neutral not needed), max 350 / 600VAC * Mains/Bus voltage L1,L2,L3, (N) 3x120 / 277 Ph-N or 208 / 480 Ph-Ph VAC
(neutral not needed), max 350 / 600VAC, CAT III Generator current L1k,L1l, L2k,L2l,
L3k,L3l 0 ÷ 5 Amps, max 10 A all time, 150 A for 2 sec 0 ÷ 1 Amp, max 2 Amps all time
Neutral/Mains current LNk,LNl 0 ÷ 5 Amps, max 10 A all time, 150 A for 2 sec 0 ÷ 1 Amp, max 2 Amps all time
IG-AVRi interface AVRI-OUT, AVRI-COM TTL (5V PWM) interface to IG-AVRi Power supply + , - 8 ÷ 36 VDC D+ D plus Inputs and outputs Binary inputs BI1 ÷ BI6
BI7 ÷ BI16 Activation to minus power supply.
Binary outputs BO1 ÷ BO6 BO7 ÷ BO16
Load is connected to plus power supply.
Analog inputs AI1 ÷ AI4 Ohms, mA, Volts sensors Analog outputs SG-OUT, SG-COM
AOUT+, AOUT-COM Speed governor output interface (±10V / 5V PWM; 500 – 3000Hz) Configurable analog output, mA, V.
RPM RPM-IN, RPM-COM Min 2 Vpk-pk (from 4 Hz to 4 kHz) Communication interface RS232 (1) D SUB9 (male) PC: InteliMonitor, GenConfig or
Modem, GSM modem or ECU (e.g. Cummins ModBus) or InteliVision 8
RS232 (2) D SUB9 (male) PC: InteliMonitor, GenConfig or Modem, GSM modem or InteliVision 8
RS485 (1) ** A1,B1,COMR1 Up to 3 IS-Displays (Remote display), up to 3 InteliVision 8 displays (remote display)
RS485 (2) ** A2,B2,COMR2 Redirected RS232 (2) - see Basic settings: RS485(2)conv. PC: InteliMonitor, GenConfig or Modem, GSM modem or InteliVision 8
USB Non isolated
2.0 slave PC: InteliMonitor, GenConfig
CAN1 L1,H1,COMC1 Extension modules: IS-AIN, IS-BIN,IGS-PTM, IGL-RA15, I-AOUT
CAN2 L2,H2,CONC2 Intercontroller (Load&VAR sharing, Power management), monitoring (IG-IB, I-LB) and up to 4 InteliVision 8
Hint: * IG-MTU or IG-MTU-2-1 can be used for three wire systems, systems with separated Neutral or when galvanic separation between generator or mains voltage and controller is required. ** When more devices connected to RS485 bias resistor jumpers should be closed only on one of them.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
48
IM-NT
InteliMains – New Technology
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
49
Interface Function Terminals Note Mains voltage L1,L2,L3, (N) 3x120 / 277 Ph-N or 207 / 480 Ph-Ph VAC
(neutral not needed), max 350 / 600VAC, CAT III Bus voltage L1,L2,L3, (N) 3x120 / 277 Ph-N or 207 / 480 Ph-Ph VAC
(neutral not needed), max 350 / 600VAC, CAT III Mains current L1k,L1l, L2k,L2l, L3k,L3l 0 ÷ 5 Amps, max 10 A all time, 150 A for 2 sec
0 ÷ 1 Amp, max 2 Amps all time Aux current IAk,IAl 0 ÷ 5 Amps, max 10 A all time, 150 A for 2 sec
0 ÷ 1 Amp, max 2 Amps all time Power supply + , - 8 ÷ 36 VDC Inputs and outputs Binary inputs BI1 ÷ BI6 Activation to minus power supply. Binary outputs BO1 ÷ BO6 Load is connected to plus power supply. Communication interface RS232 (1) D SUB9 (male) PC: InteliMonitor, GenConfig or
Modem, GSM modem or ECU (e.g. Cummins ModBus) or InteliVision 8
RS232(2) None RS485 (1) ** non isolated
A1,B1,COMR1 IG-Display (Remote display) or InteliVision 8 (remote display) or for PC (via RS485 converter) = redirected RS232 (1) see Basic settings: RS485(1)conv. For IG-Display and InteliVision 8, the setpoint RS485 (1) conv has to be set to DISABLED value.
RS485 (2) None USB None CAN1 L1,H1,COMC1 Extension modules: IS-AIN8, IS-BIN16/8,IGS-
PTM, IGL-RA15, I-AOUT8 CAN2 L2,H2,CONC2 Intercontroller (Load&VAR sharing, Power
management) and monitoring (IG-IB, I-LB) and up to 4 InteliVision 8 displays
Hint: ** When more devices connected to RS485 bias resistor jumpers should be closed only on one of them.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
50
IG-NT-BB
InteliGen – New Technology – Base Box
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
51
Interface Function Terminals Note Mains voltage L1,L2,L3, (N) 277 Ph-N or 480 Ph-Ph VAC
(neutral not needed), max 600VAC, CAT III Bus voltage L1,L2,L3, (N) 277 Ph-N or 480 Ph-Ph VAC
(neutral not needed), max 600VAC, CAT III Mains current L1k,L1l, L2k,L2l, L3k,L3l 0 ÷ 5 Amps, max 10 A all time, 150 A for 2 sec Aux current IAk,IAl 0 ÷ 5 Amps, max 10 A all time, 150 A for 2 sec Power supply + , - 8 ÷ 36 VDC Inputs and outputs Binary inputs BI1 ÷ BI6 Activation to minus power supply. Binary outputs BO1 ÷ BO6
BO7 ÷ BO12 Load is connected to plus or minus power supply (defined in GenConfig).
Communication interface RS232 (1) D SUB9 (male) PC: InteliMonitor, GenConfig or
Modem, GSM modem or ECU (e.g. Cummins ModBus) or InteliVision 8
RS485 (Display) ** non isolated
A1,B1,COMR1 IG-Display (Remote display) or InteliVision 8 (remote display) or for PC (via RS485 converter) = redirected RS232 (1) see Basic settings: RS485(1)conv. For IG-Display and InteliVision 8, the setpoint RS485 (1) conv has to be set to DISABLED value.
CAN1 L1,H1,COMC1 Extension modules: IS-AIN8, IS-BIN16/8,IGS-PTM, IGL-RA15, I-AOUT8, ECU
CAN2 L2,H2,CONC2 Intercontroller (Load&VAR sharing, Power management) and monitoring (IG-IB, I-LB) and up to 4 InteliVision 8 displays
Hint: ** When more devices connected to RS485 bias resistor jumpers should be closed only on one of them.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
52
IG-NTC-BB
InteliGen – New Technology - Option C – Base Box
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
53
Interface Function Terminals Note Generator voltage L1,L2,L3, (N) 3x120 / 277 Ph-N or 207 / 480 Ph-Ph VAC
(neutral not needed), max 350 / 600VAC *, CAT III Mains/Bus voltage L1,L2,L3, (N) 3x120 / 277 Ph-N or 207 / 480 Ph-Ph VAC
(neutral not needed), max 350 / 600VAC, CAT III Generator current L1k,L1l, L2k,L2l,
L3k,L3l 0 ÷ 5 Amps, max 10 A all time, 150 A for 2 sec 0 ÷ 1 Amp, max 2 Amps all time
Neutral/Mains current LNk,LNl 0 ÷ 5 Amps, max 10 A all time, 150 A for 2 sec 0 ÷ 1 Amp, max 2 Amps all time
IG-AVRi interface AVRI-OUT, AVRI-COM TTL (5V PWM) interface to IG-AVRi Power supply + , - 8 ÷ 36 VDC D+ D plus Inputs and outputs Binary inputs BI1 ÷ BI6
BI7 ÷ BI12 Activation to minus power supply.
Binary outputs BO1 ÷ BO6 BO7 ÷ BO12
Load is connected to plus or to minus power supply. (defined in GenConfig).
Analog inputs AI1 ÷ AI4 Ohms, mA, Volts sensors Analog outputs SG-OUT, SG-COM
AOUT+, AOUT-COM Speed governor output interface (±10V / 5V PWM; 500 – 3000Hz) Configurable analog output, mA, V.
RPM RPM-IN, RPM-COM Min 2 Vpk-pk (from 4 Hz to 4 kHz) Communication interface RS232 (1) D SUB9 (male) PC: InteliMonitor, GenConfig or
Modem, GSM modem or ECU (e.g. Cummins ModBus) or InteliVision 8
RS485 (Display) ** A1,B1,COMR1 Up to 3 IS-Displays (Remote display), up to 3 InteliVision 8 displays (remote display) or 3 InteliVision 5.
RS485 (2) ** A2,B2,COMR2 Redirected RS232 (2) – see Basic settings: RS485(2)conv. PC: InteliMonitor, GenConfig or Modem, GSM modem or InteliVision 8
USB Electrical isolated
2.0 slave PC: InteliMonitor, GenConfig
CAN1 L1,H1,COMC1 Extension modules: IS-AIN, IS-BIN,IGS-PTM, IGL-RA15, I-AOUT
CAN2 L2,H2,CONC2 Intercontroller (Load&VAR sharing, Power management), monitoring (IG-IB, I-LB) and up to 4 InteliVision 8
RJ45 (Ethernet) Ethernet cable Remote monitoring via Ethernet, InteliMonitor, WebSupervisor and etc…
Hint: ** When more devices connected to RS485 bias resistor jumpers should be closed only on one of them.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
54
IS-NTC-BB
InteliSys – New Technology – Base Box
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
55
Interface Function Terminals Note Generator voltage L1,L2,L3, (N) 3x120 / 277 Ph-N or 207 / 480 Ph-Ph VAC
(neutral not needed), max 350 / 600VAC *, CAT III Mains/Bus voltage L1,L2,L3, (N) 3x120 / 277 Ph-N or 207 / 480 Ph-Ph VAC
(neutral not needed), max 350 / 600VAC, CAT III Generator current L1k,L1l, L2k,L2l,
L3k,L3l 0 ÷ 5 Amps, max 10 A all time, 150 A for 2 sec 0 ÷ 1 Amp, max 2 Amps all time
Neutral/Mains current LNk,LNl 0 ÷ 5 Amps, max 10 A all time, 150 A for 2 sec 0 ÷ 1 Amp, max 2 Amps all time
IG-AVRi interface AVRI-OUT, AVRI-COM TTL (5V PWM) interface to IG-AVRi Power supply + , - 8 ÷ 36 VDC D+ D plus Inputs and outputs Binary inputs BI1 ÷ BI6
BI7 ÷ BI16 Activation to minus power supply.
Binary outputs BO1 ÷ BO6 BO7 ÷ BO16
Load is connected to plus or to minus power supply. (defined in GenConfig).
Analog inputs AI1 ÷ AI4 Ohms, mA, Volts sensors Analog outputs SG-OUT, SG-COM
AOUT+, AOUT-COM Speed governor output interface (±10V / 5V PWM; 500 – 3000Hz) Configurable analog output, mA, V.
RPM RPM-IN, RPM-COM Min 2 Vpk-pk (from 4 Hz to 4 kHz) Communication interface RS232 (1) D SUB9 (male) PC: InteliMonitor, GenConfig or
Modem, GSM modem or ECU (e.g. Cummins ModBus) or InteliVision 8
RS485 (Display) ** A1,B1,COMR1 Up to 3 IS-Displays (Remote display), up to 3 InteliVision 8 displays (remote display) or 3 InteliVision 5.
RS485 (2) ** A2,B2,COMR2 Redirected RS232 (2) – see Basic settings: RS485(2)conv. PC: InteliMonitor, GenConfig or Modem, GSM modem or InteliVision 8
USB Electrical isolated
2.0 slave PC: InteliMonitor, GenConfig
CAN1 L1,H1,COMC1 Extension modules: IS-AIN, IS-BIN,IGS-PTM, IGL-RA15, I-AOUT
CAN2 L2,H2,CONC2 Intercontroller (Load&VAR sharing, Power management), monitoring (IG-IB, I-LB) and up to 4 InteliVision 8
RJ45 (Ethernet) Ethernet cable Remote monitoring via Ethernet, InteliMonitor, WebSupervisor and etc…
Hint: ** When more devices connected to RS485 bias resistor jumpers should be closed only on one of them.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
56
IS-NTC-BB Jumper Settings
Hint: IG-NT-BB, IG-NTC-BB, IS-NTC-BB have the same jumpers position
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
57
Hint: IP setting could be recovered to default state when Jumper for default configuration is used. See the picture above.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
58
Wiring
General Tightening torque, allowable wire size and type, for the Field-Wiring Terminals:
For Mains(Bus) Voltage and Generator Voltage terminals Specified tightening torque is 0,56Nm (5,0 In-lb) Use only diameter 2,0-0,5mm (12-24AWG) conductor, rated for 90°C minimum.
For other controller field wiring terminals Specified tightening torque 0,79Nm (7,0 In-lb) Use only diameter 2,0-0,5mm (12-26AWG) conductor, rated for 75°C minimum.
Use copper conductors only.
To ensure proper function: Use grounding terminals. Cables for binary inputs and analogue inputs must not be placed along power cables. Analog and binary inputs should use shielded cables, especially when length exceeds 3m.
Power supply To ensure proper function:
Use power supply cable min. 2,5mm2 Use fuse 1 amps for IG-NT, IG-NTC
2 amps for IS-NT, IS-NTC-BB, IG-NT-BB, IG-NTC-BB Maximal continuous DC power supply voltage is 36VDC. See chapter Technical data. Hint: Switchboard lightning strikes protection according standard regulation is expected !!! The maximum allowable current through the controller negative terminal is 3 to 8A (depends on controller type and binary output load).
Power supply fusing A (2) respectively (1) amp fuse should be connected in-line with the power to the controller and modules, these items should never bee connected directly to the starting battery. Take care for proper controller, extension units and relays power supply fusing. Fuse value and type depends on number of connected devices and wire length. Recommended fuse (not fast) types:
Controller or unit Fuse Controller T1A orT2A IS-AIN8 T2A IS-BIN16/8 T1A
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
59
For more extension units use separate fusing according to the table above. Controller power supply should never be connected to starter terminals. For the connections with 12VDC power supply an I-LBA module can be connected to controller power terminals in order to allow the controller to continue operation during cranking if the battery voltage dip occurs. In this case, it is not recommended to use +PWR BOUT outputs on the controller as a source for relays, as their consumption would exhaust I-LBA capacitors very fast.
+
-
12VDC+-
controllerT2A
Battery
Relays
I-LBA
+
-
+
-
Grounding To ensure proper function: The shortest possible piece of wire should be used for controller grounding. Use cable min. 2,5mm2 Brass M4x10 screw with star washer securing ring type grounding terminal shall be used.
Magnetic pick-up To ensure proper function: Use a shielded cable Take care to interference signal when one common speed pick-up is used for both Speed governor and Controller. When some problems occur:
- check grounding connection from pick-up to controllers, disconnect ground connection to one of them.
- galvanically separate Controller RPM input using ComAp separation transformer RPM-ISO (1:1).
- use separate pick-up for Speed governor and Controller. Controller indicates "Sd Underspeed" + "Pickup fault" after engine start when the pickup signal is good for start and low speed but too strong for higher speed (loss of signal due to RPM input saturation). Increase gap between pickup and engine flywheel or change pickup type.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
60
Hint: If RPM is measured from the generator voltage (Gear teeth = 0), controller can detect RPM on no running gen-set when:
• Controller generator voltage terminals are opened (e.g. due to opening of fuse switch) • Non zero RPM causes controller “Not ready” state and engine start is blocked.
GENERATORL1L2L3
N
L1L2L3
N
MAINSVOLTAGE
GENERATORVOLTAGE
L1 L2 L3 L3L2L1N
MCB GCBMAINS
LOAD
N
Active NPN pick-up sensor recommended connection
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
61
Voltage measurement Four-wire generator and mains or bus
Four-wire generator and three wire mains or bus
G
GENERATOR MAINS / BUSL3L2L1N LL2L1N
L1
L2L3
N
3
Three-wire generator and mains or bus
G
GENERATOR MAINS / BUSL3L2L1N LL2L1N
L1
L2L3
3
Hint: No separation transformers for three wires voltage connection (without N) are needed. Switchboard flash protection according standard regulation is expected!
T 1 T2
0V
L1 L2 L3
VOLTAGE TERMINALS
0V 100V
100V
MAINS/BUSGENERATOR L1
L3L2
Principle of two transformers measuring - typical wiring for high voltage application spare of one transformer.
Voltage measurement separation For optional separation of Mains/bus and generator voltage from the controller (e.g. on ships) use IG-MTU.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
62
IG MTU Connect one or two IG-MTU units to separate generator and Mains/bus voltage from controller. Three wire mains Three wire mains and three wire genset or electric
separation
T1 T3T2
L1
L3L2
L3
GENERATORL1 MAINS / BUSL2
400V
400V
400V
0V0V 0V
0V 0V0V40
0V
400V
400V
L1 L3
MAINS / BUS VOLTAGE
L2 L1 L2 L3
GENERATORVOLTAGE
N
IG-MTU
NN
Ix-NT
T1 T3T2 T1 T3T2
L1
L3L2
L3
GENERATORL1
MAINS / BUS
L2
400V
400V
400V
L1 L3
MAINS / BUSVOLTAGE
L2
Ix- NT
L1 L2 L3
GENERATOR
VOLTAGE
N
IG- MTUIG- MTU
0 V 0 V
0 V
400V
400V
400V
0 V
0 V
0 V
400V
400V
400V
0 V
0 V
0 V
400V
400V
400V
0 V
0 V
0 V
N
Current measurement To ensure proper function: • Use cables of 2,5 mm2 • Use 5A transformers • Connect CT according to following drawings
L1L2L3
N
G
I1k I1l
K Lk l
I2k I2l
K Lk l
I3k I3l
K Lk l
Standard three CT connection
L1L2L3
G
I1k I1l
K Lk l
I2k I2l
K Lk l
I3k I3l
Two CT connection Typical wiring for middle-high voltage application spare of one transformer.
Mains power and PF measuring
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
63
G
GENERATOR
I3k I3l
L1L2L3
N
K Lk l
I1k I1l
K Lk l
I2k I2l
K Lk l
MAINS
Inl Ink
L Kl k
Hint: Please, check carefully all current and voltage connections and sensing input rotations before final operation. Some possible problems might occur e.g.: Power is measured in Island operation correctly without any measurement failure. In Mains Parallel operation is measured power 10kW; with currents 3x 125A and Cos phi 0.01. It might be caused with wrongly connected voltage (Cyclic false connection) sensing. Correctly connected sensing has to be connected in order L1-L2-L3. In the case of example it is in following order: L3-L1-L2; L2-L3-L1 (No reverse rotation; just cyclic interchanged)
Earth fault protection Earth fault current protection is active only when Process control: IE measurement = ANALOG INPUT or NONE. Connect separate current transformer to gen-set neutral. Adjust EarthFltCurrCT in Basic settings and EarthFaultCurr and EthFltCurr del limits in Generator protection group.
G
I1k I1l I3k I3lI2k I2l
K Lk l
L1L2L3
N
Ink Inl
K Lk l K L
k l
L K
l k
The simplest arrangement covers all zones from the generator windings to the final circuits in the load network.
GL1L2L3
N
Ink Inl
k lk lk lk l
This arrangement covers earth faults in the load network only.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
64
GL1L2L3
N
Ink Inl
L K
l k
k lk lk lk l
K L
This arrangement necessary for restricted earth fault protection. The location of the neutral earthing point in relation to the protection current transformers in the neutral conductor determines whether four or five current transformers are employed.
GL1L2L3
N
Ink Inl
k lk lk lk l
This arrangement necessary for restricted earth fault protection. The location of the neutral earthing point in relation to the protection current transformers in the neutral conductor determines whether four or five current transformers are employed.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
65
Recommended wiring IG-NT – SPTM application
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
66
Recommended wiring IG-NT – SPI application
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
67
Recommended wiring IG-NT – MINT application
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
68
Single phase applications There is no special archive file or software for single phase applications. Use standard archive.
Recommended wiring Generator (Mains) single phase voltage has to be connected to all three voltage terminals L1, L2, L3. Generator current has to be connected to L1k, L1l terminals only. Adjust setpoint Gener protect:Gen I unbal to 200%. For single phase measurement of Mains import/export power connect L3 current transformer to Ink and Inl terminals of the controller. Measured power is internally multiplied by 3. Adjust correctly setpoints Basic settings:Im3/ErFlCurCTp and Im3/ErFlCurCTs.
Hint: Recommended wiring is applicable on IG-NT, IG-NT-BB, IG-NTC-BB, IS-NT, IS-NTC-BB.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
69
Controller Binary inputs and outputs
Binary output via I-RB16
Wiring example 1
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
70
Wiring example 2
Wiring example 3
Hint: If +PWR BOUT are used, the controller consumption is increased by all relays connected. Therefore, an I-LBA module cannot be used. Use maximum 2,5A fuses. Wiring of I/O is the same for IM-NT It is recommended to separate inputs by diodes when two or more binary inputs are connected in parallel to avoid wrong input activation when one controller is switched off.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
71
IG/IS-NTBIBI
IG/IS-NT
Wiring example 4
IG-NT-BB Binary Input/Output wiring
Binary output
Low side switch High side switch
Hint: Both Power supplies socket with + BATT and GND have to be used to ensure proper BO function.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
72
It is recommended to separate inputs by diodes when two or more binary inputs are connected in parallel to avoid wrong input activation when one controller is switched off. Wiring of I/O is the same for IG-NT-BB, IG-NTC-BB and IS-NTC-BB controllers.
Binary Input
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
73
Binary inputs on IS-BIN16/8 There are two groups of eight Binary inputs BI1 to BI8 and BI9 to BI16. Each group has a separate Common terminal COM1 and COM2. The Common terminal can be connected to positive or negative pole – see following drawing. Binary inputs are galvanically separated from IS-BIN16/8 power supply. A Binary inputs Common terminal is connected to positive supply terminal, Binary inputs contacts are closed to negative supply terminals.
Binary inputs common terminal is connected to negative supply terminal, Binary inputs contacts are closed to positive supply terminals.
BI 1 ( BI 9)BI 2 ( BI 10)BI 3 ( BI 11)
BI 8 ( BI 16)COM 1 ( COM 2) +
8 - 36 V-
POWER -POWER +
+8 - 36 V
-
BI 1 ( BI 9)BI 2 ( BI 10)BI 3 ( BI 11)
BI 8 ( BI 16)COM 1 ( COM 2)POWER +POWER -
Input voltage range for opened contact is from 8 VDC to Power supply VDC. Input voltage range for closed contact is from 0 to 2 VDC. Voltage level is defined between Binary input and Binary input COM terminal and does not depend on “positive” or “negative” connection. Impulse inputs do not work with IGS-NT controller.
Binary outputs on IS-BIN16/8 IS-BIN16/8 binary outputs are galvanically separated from IS-BIN16/8 power supply. It is necessary to connect plus 24 VDC (power supply ) to IS-BIN16/8 terminal according to following drawing. The maximum load values are 0.5 A / 36V for one output.
IS-B
IN16
/8
Binary output protections Controller inputs and outputs terminals are protected against transient disturbance. Protection capability is limited. Never use DC relays without protection diodes. Use protection diodes at all relays in the switchboard even if they are not connected directly to controller Binary outputs.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
74
+-
K1 K1K2 K2
ControllerT2A
Fuse
Fuse
Battery
DC relays
HUGELOADS
STARTER
+8 - 36 V-
Example of controller protection
Dongle installation Dongle for load sharing, power management and additional PLC functions should be installed from the rear side of the controller under the rubber plug. The dongle label should remain visible as shown on the picture.
BI 1
BI 6
BI 7 BI 1
2
BO
1
BO
8
BO
9
BO
12
+BA
TTG
ND
AV
Ri O
UT
AVR
i CO
M
D+
RS
232 (1)
ABC
OM HL
CO
M HLC
OM
N L1 L2 L3 N L1 L2 L3
I1K
I1L
I2K
I2L
I3K
I3L K L
BO
2B
O3
BO
4B
O 5
BO
6B
O 7
BO
10
BO
11
BI 8
BI 9 BI 1
0B
I 11
BI 2
BI 3
BI 4 BI 5
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
75
IS-NT Jumpers Controller hardware jumpers:
Function Jumper options Software configuration Analog inputs Current
Voltage Resistance
Required
Speed governor output ± 10VDC voltage output (use SpdGovPWM rate = 1200 Hz) ± 10VDC voltage output via 10 kΩ resistor (use SpdGovPWM rate = 1200 Hz) PWM 500 – 3000Hz (SpdGovPWM rate setpoint)
Not needed
Analog output 0 to 20 mA 0 to 10 VDC
Not needed
CAN or RS485 terminating resistors
Closed jumper connects 120Ω resistor to CAN1, CAN2, RS485-1, RS485-2
Not needed
Analog input jumpers
Current range: 0 to 25 mA (max) Voltage range: 0 to 5 VDC (max) Resistive range: 0 to 2400 Ω
Speed governor output jumper
SG COMSG OUT
PWM
SG COMSG OUT
VoutR
SG COMSG OUTVout
Pulse Width Modulation 1200 Hz / 5V / 10mA max V-outR range: ± 10 VDC via 10 kΩ V-out range: ± 10 VDC
Hint:
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
76
SG COM is internally connected to controller 0VDC power supply. IS-NT-BB and IS-NTC-BB have the same jumper position. For more details about IS-NTC-BB see the chapter IS-NTC-BB Jumper Settings.
Analog output jumper
Voltage Voltage range: 0 to 10 VDC
AI 4
AI 3
AI 2
AI 1
AI C
OM
SG
OU
TS
G C
OMA
OU
T +A
OU
T CO
M
RP
M IN
RP
M C
OM
Current Current range: 0 to 20 mA
AI 4
AI 3
AI 2
AI 1
AI C
OM
SG
OU
TS
G C
OMA
OU
T +A
OU
T CO
M
RP
M IN
RP
M C
OM
AOUT COM is internally connected to controller 0 VDC power supply.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
77
Analog inputs wiring examples
Resistive sensors (two wires)
Resistive sensors (one wire)
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
78
Current sensors
Current and resistive sensors
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
79
Voltage and resistive sensors
Hint: Analog input has to be configured for voltage input when thermocouples are used. Correct curve is necessary for different type of thermocouples. Resistive sensors like PT 100/1000, Ni600 have to be used with resistive settings on analog input.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
80
Tristate sensors
Hint: Tri state sensor connection is the same for all IG/IS-NT controllers:connection is For more details see the chapter IS-NTC-BB Jumper Settings.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
81
Isolated analogue inputs Grounded analogue inputs
Analog inputs on IS-AIN8 IS-AIN8 extension module analog inputs can be configured to
• Resistor two wire input • Resistor three wire input • Current input • Thermocouple input • Voltage input
Select sensor characteristic from the list or define user sensor characteristic in PC configuration tool.
ABCD
Resistor sensor input – two wire connection. Range 0 to 2400 ohms. Pt100, Pt1000, Ni100, Ni1000 D terminal is shielding
ABCD
Resistor sensor input – three wire connection. Range 0 to 2400 ohms. Pt100, Pt1000, Ni100, Ni1000 – recomended. D terminal is shielding
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
82
ABCD
Passive current sensor (current source is in IS-AIN8) Range 0 to + 20 mA or 4 to + 20 mA D terminal is shielding
ABCD
+ +24 VDC
0 VDCSensor
mA
ABCD
+
+24 VDC
0 VDC
SensormA
Active current sensor (current source is in sensor) Range –20mA to +20 mA or 4 to + 20 mA D terminal is shielding
ABCD
+
Thermocouple J, K, L D terminal is shielding From IS-AIN8 hardware version 5.1 can be B terminal grounded to frame
ABCD
+
Voltage input Range 0 to + 2500 mV. Voltage range is 0 to ± 1000 mV. D terminal is shielding
ABCD
+
R1
R2
For 10V input voltage range connect external resistors R1, R2 and select sensor characteristic 10V. R1=10 kohm, R2=2,7 kohm. D terminal is shielding
Hint: Thermocouples connected to IS-AIN8 hardware versions below 5.0 must be galvanically separated from the frame. If the thermocouples are connected to IS-AIN8, appropriate jumpers must be removed (see rear sticker).
External modules connection IS-BIN16/8 is an extension module with 16 binary inputs and 8 binary outputs. IS-AIN8 is an extension module with 8 analog inputs. All I/O can be configured to any logical function or protection. It is possible to connect up to 10 IS-AIN8 and 4 IS-BIN16/8 external units to one CONTROLLER. External modules IS-BIN16/8 and IS-AIN8 are connected to CONTROLLER CAN1 bus. Controllers are connected to CONTROLLER CAN2 bus in multiple applications. To operate external modules
• Connect all external modules to CAN1 bus line
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
83
• On each module adjust I/O CAN1 address in the range of 1 to 7 for IS-BIN16/8 inputs, 1 to 4 for IS- BIN16/8 outputs (address 0 switches corresponding communication OFF) or 0 to 9 for IS-AIN8 (0 has address 10 meaning).
• Input output address is displayed on the front panel LED’s • Use PC configuration tool to configure CONTROLLER according external modules setting
IS-BIN16/8 module has two separate CAN1 addresses for binary inputs Group 1, Group 2 and binary outputs Group (total three addresses). The CAN1 address for BI Group 1 and for BO Group 2 can be adjusted on the IS-BIN16/8. The address for BI Group 2 is set automatically to the address following BI Group 1. Hint: CAN address 0 disables corresponding CAN message (Group data are not send).
IS-AIN8, IS-BIN8/16 address setting • Press Address button during IS-AIN8 power supply on to switch to addressing mode. • Then repeatedly press or keep pressed address button to adjust required address according to
CONTROLLER configuration. • After setting requested address, release the buttons and wait until the digits blink – it indicates
write the changed address to EEPROM memory.
IS-AIN8, IS-BIN8/16 SW version check Let suppose IS-AIN8 of SW version 1.4. Shortly press address button. Following sequence appears on the display: number “1”, one second pause, number “4”, two second pause, number “1”, one second pause, number “4”, two second pause and finally IS-AIN8 actual address. Error message (e.g. SD BOUT2) appears on Controller screen when Binary input or output Address x is configured but corresponding unit is not recognized (no message is received from CAN bus). Check IS configuration and corresponding external IS-AIN, IS-BIN unit address setting.
CA
N1
CA
N2
CA
N1
CA
N1
CA
N1
CA
N1
120
CA
N1
CA
N2
Hint: CAN bus line has to be terminated by 120 ohm resistors on the both ends. Always check the number and placement of terminating resistors in the CAN bus line, only correct wiring ensures reliable operation! Resistors must be placed at either end of the line (see picture), and correct number of resistors must be used! Correct number can be checked using ohmmeter - when power supply for ALL devices on the CAN bus line (including third party, e.g. ECU) is switched off, the resistance measured between A and B wire should be 60 Ohms.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
84
For longer distances is recommended to connect one CAN COM terminal (one connection for whole site) and cable shielding to the ground in one point. External units can be connected on the CAN bus line in any order, but line arrangement (no tails, no star) is necessary. Recommended CAN bus data cables see in Chapter Technical data. IG-MU and IG-IB units are connected to CONTROLLER CAN2 bus.
IGS-PTM and IGL-RA15 module connection It is possible to connect up to four IGS-PTM and one IGL-RA15 to one CONTROLLER. IGS-PTM can be connected to CONTROLLER like IS-AIN8 and IS-BIN16. IGS-PTM behaves like IS-AIN8 and IS-BIN16/8 modules in one unit. IGS-PTM and I-CB units contain internal jumper removable 120-ohm resistor.
CA
N1
CA
NH
CA
NL
CA
NL
CAN
HC
OM
CA
NL
CAN
HC
OM
CA
N1
CA
NL
CAN
HC
OM
CA
NL
CAN
HC
OM
CA
NL
CAN
HC
OM
CA
N1
CA
N2
CA
N1
CA
N2
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
85
Connection of ECU on CAN1
CAN1
CA
N1
CA
NL
CAN
HC
OM
CA
NL
CAN
HC
OM
CA
N1C
AN2
CA
N1C
AN2
ECU communicating over the CAN bus is connected to CAN1 port of the controller and other ComAp modules can be connected to this CAN bus as well. For detailed description of connection of various ECUs refer to ComAp Electronic Engines Support manual.
CAN bus Tx, Rx LED indication Tx and Rx LED is connected directly to Tx and Rx signal.
Status Tx Rx Communication is OK Fast flashing – data transfer CAN bus is interrupted Continuous light Continuous light Short connection H – L Fine flashing Dark Short connection L – COM Dark Dark Short connection H – COM Fine flashing Dark Wrong connection H – H, L – L Synchro flashing
I-CB wiring and configuration
CAN H
CAN L
EngineControl Unit
Controller
CAN HCAN L
CA N L
CAN HC O M
CAN L
CAN HCO M
CAN H
CAN L
I-CB
CAN 1 CAN ECU
ECU
1. Configure I-CB using I-CBEdit software. Configured I-CB behaves like fictive IS-AIN and IS-BIN
units. I-CB configuration associates selected values (from ECU database) received from Engine Control Unit to selected CAN addressees (fictive IS-AIN, IS-BIN inputs and outputs).
2. Configure corresponding CONTROLLER CAN addresses and tick in PC configuration tool.
3. Configure separate inputs and outputs in corresponding Analog, Binary inputs, outputs in PC configuration tool.
Hint: In case of CAT engines, there is RS232 connection between I-CB and CCM.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
86
Recommended CAN/RS485 connection
CAN bus connection The bus has to be terminated by 120 Ohm resistors at both ends. External units can be connected on the CAN bus line in any order, but keeping line arrangement (no tails, no star) is necessary. Standard maximum bus length is 200m for 32C CAN BUS MODE and 900m for 8C CAN BUS MODE Shielded cable has to be used, shielding has to be connected to PE on one side (controller side). A) For shorter distances (all network components within one room) – picture 1 Interconnect H and L; shielding connect to PE on controller side B) For longer distances (connection between rooms within one building) – picture 2 Interconnect H, L, COM; shielding connect to PE in one point C) In case of surge hazard (connection out of building in case of storm etc.) – picture 3 We recommend to use following protections: - Phoenix Contact (http://www.phoenixcontact.com): PT 5-HF-12DC-ST with PT2x2-BE (base element) - Saltek (http://www.saltek.cz): DM-012/2 R DJ Recommended data cables: BELDEN (http://www.belden.com) A) For shorter distances: 3105A Paired - EIA Industrial RS-485 PLTC/CM (1x2 conductors) B) For longer distances: 3106A Paired - EIA Industrial RS-485 PLTC/CM (1x2+1 conductors) C) In case of surge hazard: 3106A Paired - EIA Industrial RS-485 PLTC/CM (1x2+1 conductors)
RS485 connection The line has to be terminated by 120 Ohm resistors at both ends. External units can be connected on the RS485 line in any order, but keeping line arrangement (no tails, no star) is necessary. Standard maximum link length is 1000m. Shielded cable has to be used, shielding has to be connected to PE on one side (controller side). A) For shorter distances (all network components within one room) – picture 1 interconnect A and B; shielding connect to PE on controller side B) For longer distances (connection between rooms within one building) – picture 2 interconnect A, B, COM; shielding connect to PE in one point C) In case of surge hazard (connection out of building in case of storm etc.) – picture 3 We recommend to use following protections: - Phoenix Contact (http://www.phoenixcontact.com): PT 5-HF-5DC-ST with PT2x2-BE (base element) (or MT-RS485-TTL) - Saltek (http://www.saltek.cz): DM-006/2 R DJ Recommended data cables: BELDEN (http://www.belden.com) A) For shorter distances: 3105A Paired - EIA Industrial RS-485 PLTC/CM (1x2 conductors) B) For longer distances: 3106A Paired - EIA Industrial RS-485 PLTC/CM (1x2+1 conductors) C) In case of surge hazard: 3106A Paired - EIA Industrial RS-485 PLTC/CM (1x2+1 conductors)
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
87
Picture 1 - shorter distances (all network components within one room) 120 Ω 120 Ω Picture 2 - longer distances (connection between rooms within one building)
CAN1 H
COML
CAN2
120
1.iS-CUAddr.: 1Addr.: 1
CAN1
CAN1
8.iS-AINAddr.: 8
7.iS-BINAddr.: in13
out7
CAN1
CAN1
1.iS-AINAddr.: 1
120
1.iS-BINAddr.: in1
out1
CAN1
CAN2
2.iS-CU
120
HCOM
L
HCOM
LH
COML
HCOM
L
HCOM
LH
COML
HCOM
L
Picture 3 - surge hazard (connection out of building in case of storm etc.) 120 Ω 120 Ω
PT5-HF-12DC-ST (CAN) PT5-HF-5DC-ST (RS485)
H/A L/B COM
H/A L/B COM
H/A L/B COM
H/A L/B COM
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
88
Default Sensors
Default characteristics
Controller
VDO Temp VDO Press ohms 1°C 1°F ohms 1 bar psi
Primary Converted Converted Primary Converted Converted 29,0 51,0 69,0 95,0 135,0 195,0 290,0 440,0
700,00 1800,0 3200,0
110 90 80 70 60 50 40 30 20 0
-16
230 194 176 158 140 122 104 86 68 32 3
10,0 50,0 85,0 119,0 152,0 180,0
0,0 2,0 4,0 6,0 8,0
10,0
0 29 58 87 116 145
Tristate sensor Resistance Considered as < 750Ω Inactive 750 - 2700Ω Active > 2700Ω Sensor failure (interrupted wire)
IS-AIN8 PT100 (IEC 571) PT1000 (IEC 571) Ni100 (IEC 43760) Ni1000 (IEC 43760)
0,1 Ù 0,1 °C 0,1 °F 0,1 Ù 0,1 °C 0,1 °F 0,1 Ù 0,1 °C 0,1 °F 0,1 Ù 0,1 °C 0,1 °F843, 922, 1000, 1078, 1155, 1232, 1309, 1385, 1461, 1536, 1610, 1685, 1758, 1832, 1905, 1977, 2049, 2120, 2191, 2262, 2332, 2401,
-400, -200, 0, 200, 400, 600, 800, 1000, 1200, 1400, 1600, 1800, 2000, 2200, 2400, 2600, 2800, 3000, 3200, 3400, 3600, 3800,
-400, -40, 320, 680, 1040, 1400, 1760, 2120, 2480, 2840, 3200, 3560, 3920, 4280, 4640, 5000, 5360, 5720, 6080, 6440, 6800, 7160,
7800, 8000, 8200, 8400, 8600, 8800, 9000, 9200, 9400, 9600, 9800, 10000, 10200, 10400, 10600, 10800, 11000, 11200, 11400, 11600, 1800, 12000,
-558, -508, -457, -407, -356, -306, -255, -204, -153, -102, -51, 0,
51, 103, 154, 205, 257, 308, 360, 412, 464, 516,
-684, -594, -503, -413, -321, -231, -139, -47, 45, 136, 228, 320, 412, 505, 597, 689, 783, 874, 968,
1062, 1155, 1249,
695, 743, 791, 841, 893, 946,
1000, 1056, 1112, 1171, 1230, 1291, 1353, 1417, 1483, 1549, 1618, 1688, 1760, 1833, 1909, 1986,
-600, -500, -400, -300,-200, -100,
0, 100, 200, 300, 400, 500, 600, 700, 800, 900, 1000,1100,1200,1300,1400,1500,
-760, -580, -400, -220, -40, 140, 320, 500, 680, 860, 1040,1220,1400,1580,1760,1940,2120,2300,2480,2660,2840,3020,
7909, 8107, 8308, 8512, 8717, 8925, 9135, 9347, 9562, 9780, 10000, 10223, 10448, 10676, 10907, 11140, 11376, 11615, 11857, 12102, 12350, 12601,
-500, -450, -400, -350, -300, -250, -200, -150, -100, -50, 0, 50, 100, 150, 200, 250, 300, 350, 400, 450, 500, 550,
-580, -490, -400, -310, -220, -130, -40, 50,
140, 230, 320, 410, 500, 590, 680, 770, 860, 950, 1040,1130,1220,1310,
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
89
PT100 (IEC 571) PT1000 (IEC 571) Ni100 (IEC 43760) Ni1000 (IEC 43760) 0,1 Ù 0,1 °C 0,1 °F 0,1 Ù 0,1 °C 0,1 °F 0,1 Ù 0,1 °C 0,1 °F 0,1 Ù 0,1 °C 0,1 °F2470, 2539, 2607, 2675, 2742, 2809, 2875, 2941, 3006, 3072, 3136, 3200, 3264, 3327, 3389, 3451, 3513, 3574, 3635, 3695, 3755, 3815, 3874, 3903,
4000, 4200, 4400, 4600, 4800, 5000, 5200, 5400, 5600, 5800, 6000, 6200, 6400, 6600, 6800, 7000, 7200, 7400, 7600, 7800, 8000, 8200, 8400, 8500,
7520, 7880, 8240, 8600, 8960, 9320, 9680, 10040 10400 10760 11120 11480 11840 12200 12560 12920 13280 13640 14000 14360 14720 15080 15440 15620
12200, 12400, 12600, 12800, 13000, 13200, 13400, 13600, 13800, 14000, 14200, 14400, 14600, 14800, 15000, 15200, 15400, 15600, 15800, 16000, 16200, 16400, 16600, 16800, 17000, 17200, 17400, 17600, 17800, 18000, 18200, 18400, 18600, 18800, 19000, 19200, 19400, 19790,
568, 620, 672, 724, 776, 829, 881, 934, 987,
1039, 1092, 1145, 1198, 1251, 1304, 1358, 1411, 1645, 1518, 1572, 1625, 1679, 1733, 1787, 1841, 1895, 1950, 2004, 2058, 2113, 2168, 2222, 2277, 2332, 2387, 2442, 2497, 2605,
1342, 1436, 1530, 1623, 1717, 1812, 1906, 2001, 2097, 2190, 2286, 2381, 2476, 2572, 2667, 2764, 2860, 3281, 3052, 3150, 3245, 3342, 3439, 3537, 3634, 3731, 3830, 3927, 4024, 4123, 4222, 4320, 4419, 4518, 4617, 4716, 4815, 5009,
2066, 2148, 2232, 2318, 2407, 2498, 2592, 2689, 2789,
1600,1700,1800,1900,2000,2100,2200,2300,2400,
3200,3380,3560,3740,3920,4100,4280,4460,4640,
12854, 13111, 13371, 13635, 13901, 14171, 14444, 14720, 15000, 15283, 15570, 15860, 16154, 16451, 16752, 17056, 17365, 17677, 17993, 18312, 18636, 18964, 19295, 19631, 19970, 20314, 20662, 21013, 21370,
600, 650, 700, 750, 800, 850, 900, 950, 1000, 1050, 1100, 1150, 1200, 1250, 1300, 1350, 1400, 1450, 1500, 1550, 1600, 1650, 1700, 1750, 1800, 1850, 1900, 1950, 2000,
1400,1490,1580,1670,1760,1850,1940,2030,2120,2210,2300,2390,2480,2570,2660,2750,2840,2930,3020,3110,3200,3290,3380,3470,3560,3650,3740,3830,3920,
4-20mA/ 100
4-20mA/ 60
0-20mA/ 100-PTM
4-20mA/ 100-PTM
Primary Converted Converted Primary Converted Primary Converted170 200 230 280 330 390 460 560 690
0 13 25 38 50 63 75 88 100
0 8 15 23 30 38 45 53 60
0 38 57 77 96 116 135 155 174 194
0 20 30 40 50 60 70 80 90 100
38 57 77 96 116 135 155 174 194
0 12 25 37 50 62 75 87 100
100mV/100-PTM
Primary Converted 0
10 40 70
110 140 170 210 230 250
0 4
16 28 45 57 68 84 92
100
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
90
Sensor fail detection (FLS) If the measured resistance, voltage or current on an analog input gets out of valid range, the sensor fail will be detected and a sensor fail message will appear in the alarmlist. The valid range is defined by the most-left (RL) and most-right (RH) points of the sensor characteristic ±12.5% from RH-RL.
Hint: The sensor fail alarm does not influence the gen-set operation. Sensor fail does not activate Binary output Alarm. If engine shutdown/stop is required when Fls appears, configure in GenConfig -> Inputs/Outputs -> Analog inputs -> Protection -> property “Active when” to Under/Over limit + Fls.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
91
Speed Governor Interface List Hint: Read carefully Speed governor instructions before connecting controller Speed governor interface!
Electronic engines interface All below mentioned interface examples describe analog interface even if they are (in some cases) used for Electronic Control Units (Electronic engines) with CAN data bus. There are several possibilities to connect CAN bus interface between Electronic engine and ComAp controller. Refer to ComAp Electronic Engines Support manual.
Communication Bridge Unit I-CB unit is an interface between Controller and Electronic engine. Following I-CB types are available: For more details see I-CB-ICBEdit-1.1.pdf manual.
I-CB type Engine I-CB/MTU MTU I-CB/MTU-SIAM4000 MTU I-CB/CAT-Diesel CAT I-CB/CAT-Gas CAT I-CB/DeutzTEMe Deutz
Speed governor interface Following chapter describes analog interface to engines with standard electronic speed governors.
Controller Speed reg out voltage limits Setpoints Sync/Ld ctrl: SpeedGovLowLim [0,01V] and SpeedGovHiLim [0,01V] limit low and high levels of output voltage. E.g. instead of full –10V to +10V Speed governor output range can be set SpeedGovLowLim = 0,00 V and SpeedGovHiLim = 5,00 V to reduce the output range from 0 to 5V. Heinzmann
Sync/Load ctrl: Speed gov bias = 0,00 V SpeedRegChar = POSITIVE
Sync/Load ctrl: Speed gov bias = 5,00 V SpeedRegChar = POSITIVE
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
92
Sync/Load ctrl: Speed gov bias = 0,00 V SpeedRegChar = POSITIVE
Terminals A3 and B3 are on OEM 14-pin connector. Mounted on Perkins 40xx engines.
Sync/Load ctrl: Speed gov bias = 5V SpeedRegChar = POSITIVE SpeedGovLowLim = 0,8V (without resistor Speed gov bias = 2,75V SpeedGovLowLim = 0V SpeedGovHiLim = 6V)
ComAp
Sync/Load ctrl: Speed gov bias = 5,1V SpeedRegChar = POSITIVE SpeedGovLowLim = 0,0V SpeedGovHiLim = 10V
Caterpillar PEEC
SG COM
SG OUT
PWM19Cate
rpill
arPE
EC 9
Pay attention to the connector and jumper orientation.
Sync/Load ctrl: SpdGovPWM rate = 500 Hz
Potentiometer turns cw (droop 0%)
Sync/Load ctrl: Speed gov bias = 5,10 V SpeedRegChar = POSITIVE SpeedGovLowLim = 0V SpeedGovHiLim = 10V
Sync/Load ctrl: Speed gov bias = 5,10 V SpeedRegChar = POSITIVE SpeedGovLowLim = 0V SpeedGovHiLim = 10V
Sync/Load ctrl: Speed gov bias = 5,10 V SpeedRegChar = POSITIVE SpeedGovLowLim = 0V SpeedGovHiLim = 10V
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
93
Sync/Load ctrl: Speed gov bias = 5,10 V SpeedRegChar = POSITIVE SpeedGovLowLim = 0V SpeedGovHiLim = 10V
PEEC
Sync/Load ctrl: SpdGovPWM rate = 500 Hz
Cummins
Cum
min
sEF
C
Spurious operation of the controller push buttons is caused by excessive interference from the speed controller when capacitor is not connected between power supply terminals 1 and 2.
Sync/Load ctrl: Speed gov bias = 6,40 V SpeedRegChar = POSITIVE SpeedGovLowLim = 5V SpeedGovHiLim = 7,8V
A 1I 9
Cum
min
sEC
PG SG COMSG OUT
Vout
Pay attention to the connector and jumper orientation.
Sync/Load ctrl: Speed gov bias = 2,50 V SpeedRegChar = POSITIVE
SG COMSG OUT
VoutR
0V5V
Cum
min
sO
NA
N
Sync/Load ctrl: Speed gov bias = 2,50 V SpeedRegChar = POSITIVE SpeedGovLowLim = 0V SpeedGovHiLim = 5V
Sync/Load ctrl: Speed gov bias = 5,00 V SpeedRegChar = POSITIVE
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
94
CU
MM
INS
QSL
9
Sync/Load ctrl: Speed gov bias = 3,50 V SpeedRegChar = POSITIVE SpeedGovLowLim = 2,5V SpeedGovHiLim = 5V
Barber Colman
SG COMSG OUT
VoutR
29
Bar
ber
Col
man
DYN
A80
00
Sync/Load ctrl: Speed gov bias = 6,00 V SpeedRegChar = POSITIVE SpeedGovLowLim = 4V SpeedGovHiLim = 8V
SG COMSG OUT
VoutR
2
Bar
ber C
olm
anD
YN1
1068
4
9
Sync/Load ctrl: Speed gov bias = 6,00 V SpeedRegChar = POSITIVE SpeedGovLowLim = 4V SpeedGovHiLim = 8V
GAC
SG COMSG OUT
VoutR
GNG
AC
ESD
550
0
Sync/Load ctrl: Speed gov bias = 5,00 V SpeedRegChar = NEGATIVE SpeedGovLowLim = 4V SpeedGovHiLim = 6V
Sync/Load ctrl: Speed gov bias = 5,00 V SpeedRegChar = NEGATIVE
SG COMSG OUT
VoutR
225G
AC
EGS
104
B
Sync/Load ctrl: Speed gov bias = 5,00 V SpeedRegChar = NEGATIVE SpeedGovLowLim = 4V SpeedGovHiLim = 6V
SG COMSG OUT
VoutR
LAG
AC
SDG
735
Sync/Load ctrl: Speed gov bias = 5,00 V SpeedRegChar = NEGATIVE SpeedGovLowLim = 2,5V SpeedGovHiLim = 7,5V Tau act.= 1
WOODWARD
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
95
WO
OD
WA
RD
ProA
ctII
Sync/Load ctrl: Speed gov bias = 0,00 V SpeedRegChar = POSITIVE SpeedGovLowLim = -2,5V SpeedGovHiLim = 2,5V
Hint: For Woodward EPG speed governor (revision F) are limits: SpeedGovLowLim = -3V SpeedGovHiLim = +2V Speed gov bias = -0,5 V
Sync/Load ctrl: Speed gov bias =0 V SpeedRegChar = POSITIVE SpeedGovLowLim = -3 V SpeedGovHiLim = 3 V
Sync/Load ctrl: Speed gov bias = 3,1 V SpeedRegChar = POSITIVE SpeedGovLowLim = 6,5 V SpeedGovHiLim = 0,0 V
Sync/Load ctrl: Speed gov bias = 5,00 V SpeedRegChar = POSITIVE
Terminals 19 and 20 are marked as analog inputs # 1.
25,26 = Speed Signal Inputs
Sync/Load ctrl: Speed gov bias = 5,00 V SpeedRegChar = POSITIVE
Sync/Load ctrl: Speed gov bias = 5,00 V SpeedRegChar = POSITIVE
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
96
For Woodward DPG 2223 the ILS terminal is 10.
Sync/Load ctrl: Speed gov bias = 2,50 V SpeedRegChar = POSITIVE SpeedGovLowLim = 0V SpeedGovHiLim = 5V
Sync/Load ctrl: Speed gov bias = 2,50 V SpeedRegChar = POSITIVE SpeedGovLowLim = 0V SpeedGovHiLim = 5V
12 SG COMSG OUT
VoutR11
Sync/Load ctrl: Speed gov bias = 0 V
MTU
SG COMSG OUT
Vout368 ( 0 to 10 VDC)
MTU
MD
EC20
00,4
000
Pay attention to the connector and jumper orientation.
Sync/Load ctrl: Speed gov bias = 4,90 V SpeedRegChar = POSITIVE SpeedGovLowLim = 0V SpeedGovHiLim = 10V
DEUTZ
SG COM
SG OUT
Vout23 GND24 (0, 5 to 4, 5 VDC)
DEU
TZBF
6M
2117
Opened for 0% Droop
Plug F
Pay attention to the connector and jumper orientation.
Sync/Load ctrl: Speed gov bias = 2,50 V SpeedRegChar = POSITIVE SpeedGovLowLim = 0,5V SpeedGovHiLim = 4,5V
PERKINS
SG COMSG OUT
Vout19
PER
KIN
S40
16E6
1TR
S
18
Pay attention to the connector and jumper orientation.
Sync/Load ctrl: Speed gov bias = 5,00 V SpeedRegChar = POSITIVE SpeedGovLowLim = 2,5V SpeedGovHiLim = 7,5V
SG COMSG OUT
VoutPER
KIN
S23
00,2
800
2024
122
Sync/Load ctrl: Speed gov bias = 2,50 V SpeedRegChar = POSITIVE SpeedGovLowLim = 0,5V SpeedGovHiLim = 4,5V
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
97
Pay attention to the connector and jumper orientation. Above mentioned pin numbers refer to the Customer Interface Connector. The J1 connector on ECM has the following numbering: 20 = J1/3; 24 = J1/17
VBREF GNDRPS INPUT
PER
KIN
S13
00ED
i
SG COMSG OUT
VoutR
Sync/Load ctrl: Speed gov bias = 2,5 V SpeedRegChar = POSITIVE SpeedGovLowLim = 0,8V SpeedGovHiLim = 4,5V
TOHO
Sync/Load ctrl: Speed gov bias = 4,00 V SpeedRegChar = POSITIVE
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
98
AVR Interface List Read carefully AVR instructions before connecting to controller! Basler: APR 63-5, AEC 63-7, KR-FX, KR-FFX
AVRi output is connected instead of external resistor for voltage adjusting.
AVRi trim to minimum counter clockwise. Volt/PF ctrl: AVR DCout bias = 50% VoltRegChar = POSITIVE
Basler: DECS 100
AVRi output is connected instead of external resistor for voltage adjusting.
AVRi trim to minimum counter clockwise. Volt/PF ctrl: AVR DCout bias = 50% VoltRegChar = POSITIVE
BASLER: DESC 200
AVRi trim to minimum counter clockwise. Volt/PF ctrl: AVR DCout bias = 50% VoltRegChar = POSITIVE
Stamford SX 460
AVRi output is connected instead of external resistor for voltage adjusting.
AVRi trim to minimum counter clockwise. Volt/PF ctrl: AVR DCout bias = 50% VoltRegChar = POSITIVE
STAMFORD SX 440, AS440, MX 321, SX 421
PFC3 module is not required.
AVRi trim to minimum counter clockwise. Volt/PF ctrl: AVR DCout bias = 50% VoltRegChar = POSITIVE
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
99
STAMFORD MX 341
iG-
AVR
i
Hint: Disconnect the droop CT (terminal S1 & S2) and short the droop CT leads short the terminal S1,S2 on the AVR
AVRi trim to minimum counter clockwise. Volt/PF ctrl: AVR DCout bias = 50% VoltRegChar = POSITIVE
Leroy Somer: R 438 LS, R448 Kutai EA448
AVRi output is connected instead Remote voltage trimmer 470 ohm to terminals ST4. Module R726 is not required.
AVRi trim to minimum counter clockwise. Volt/PF ctrl: AVR DCout bias = 50% VoltRegChar = POSITIVE
Leroy Somer: R 449
Module R726 is not required.
AVRi trim to minimum counter clockwise. Volt/PF ctrl: AVR DCout bias = 50% VoltRegChar = POSITIVE
Leroy Somer: R 450
AVRi+
AVRi-
18VACFrom generator
OUT 1
OUT2
iG-AVRiTRANS
230/400VAC0VAC
AVRI COMAVRI OUT
Hint: Use AVRi instead of potentiometer 1000 Ohm Read Leroy Somer R450 manual before use.
AVRi trim to minimum counter clockwise. Volt/PF ctrl: AVR DCout bias = 50% VoltRegChar = POSITIVE
Leroy Somer: R 129
AVRi+
AVRi-
18VACFrom generator
OUT 1
OCOM iG-
AVR
i
iG-AVRiTRANS
230/400VAC0 VAC
AVRI COMAVRI OUT
J2
AVRi output is connected instead Remote voltage trimmer 470 ohm to terminal J2. Module R726 is not required.
AVRi trim to minimum counter clockwise. Volt/PF ctrl: AVR DCout bias = 50% VoltRegChar = POSITIVE
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
100
Leroy Somer: R 221, R 222
iG-
AVR
i
Module R726 is not required. AVRi trim to minimum counter clockwise +5%. Volt/PF ctrl: AVR DCout bias = 24% VoltRegChar = POSITIVE
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
101
Leroy Somer: R 230
AVRi+
AVRi -
from generator
iG-
AVR
i
iG-AVRiTRANS
230/ 400VAC0 VAC
AVRI COMAVRI OUT
OUT1OUT2
Module R726 is not required. AVRi trim to minimum counter clockwise. Volt/PF ctrl: AVR DCout bias = 50% VoltRegChar = POSITIVE Leroy Somer: R 230
iG-
AVR
i
AVRi trim to minimum counter clockwise. Volt/PF ctrl: AVR DCout bias = 50% VoltRegChar = POSITIVE
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
102
Remove Link J4 and replace through R500 Primary voltage setting with resistors connected: 230V Hint: Disconnect one wire (OUT 1), set voltage on running Generator to U = nom. Measure Voltage over Resistor Depending on Value increase AVRi potentiometer to get Range. Set exact Value with Bias Voltage//PF regulation (gain=0) Stop gen-set and connect when equal Voltage and polarity is achieved. Set again in regulation loop on demand Leroy Somer: R 438 LS, R448
AVRi output is connected instead Remote voltage trimmer 470 ohm to terminals ST4. Module R726 is not required.
AVRi trim to minimum counter clockwise. Volt/PF ctrl: AVR DCout bias = 50% VoltRegChar = POSITIVE
Leroy Somer: R 449
AVRi trim to minimum counter clockwise. Volt/PF ctrl: AVR DCout bias = 50% VoltRegChar = POSITIVE
Leroy Somer: R 129
AVRi+
AVRi-
18VACFrom generator
OUT1
OCOM iG-
AVR
i
iG-AVRiTRANS
230/400VAC0VAC
AVRI COMAVRI OUT
J2
AVRi output is connected instead Remote voltage trimmer 470 ohm to terminal J2.
AVRi trim to minimum counter clockwise. Volt/PF ctrl: AVR DCout bias = 50% VoltRegChar = POSITIVE
Leroy Somer: R 250
AVRi+
AVRi-
18VACFrom generator
OUT1
OCOM iG-
AVR
i
iG-AVRiTRANS
230/400VAC0VAC
AVRI COMAVRI OUT
J2
AVRi trim to minimum counter clockwise. VoltRegChar = POSITIVE AVRDCout bias = 50%
Mecc Alte Spa: U.V.R.6
AVRi trim to maximum clockwise. Volt/PF ctrl: AVR DCout bias = 75% VoltRegChar = NEGATIVE
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
103
AVRi output is connected instead Remote voltage trimmer 100Kohm (OUT1=top position wire and GND =second top position).
Hint: VoltRegChar = POSITIVE is achived with IG-AVRi OUT2 and GND connection.
Mecc Alte Spa: S.R.7/2
AVRi+
AVRi-
18VACFrom generator
OUT1
GND iG-
AVR
i
iG-AVRi
TRANS
230/400VAC0VAC
AVRI COMAVRI OUT
AVRi trim to maximum clockwise. Volt/PF ctrl: AVR DCout bias = 75% VoltRegChar = NEGATIVE
Mecc Alte DSR
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
104
AVRi trim = 1/16 from minimum ( =6,25% => max. = 2,5V). Volt/PF ctrl: AVR DCout bias = 50% VoltRegChar = POSITIVE The Vext input (connector CN1 – terminals 10 and 11) permits analogical remote control of output voltage with a programmable variation range of up to ±10% (parameter 16, by default the setting is ±5%) with respect to the value set. If you want to use continuous voltage, it will be effective if it is in the range between 0V and +2,5V. The input tolerates voltages from –5V to +5V, but for values exceeding the limits of 0V / +2,5V (or in the event of disconnection) it is automatically disabled and the voltage adjustment goes back to the value set through the trimmer (if enabled) or through parameter 19 (as shown on the picture). Changing of DSR parameters requires PC with dedicated software and DI1-DSR unit! DSR automatically detects presence of transformer for parallel operation (if used it works with droop, if not used it works isochronous). Piller
AVRi output is connected instead Remote voltage trimmer 100Kohm.
AVRi trim to minimum counter clockwise. Volt/PF ctrl: AVR DCout bias = 39% VoltRegChar = POSITIVE
Catterpillar VR6, VR3F
For VR3F link 4-7 has to be removed.
AVRi trim to minimum counter clockwise. Volt/PF ctrl: AVR DCout bias = 50% VoltRegChar = POSITIVE
Caterpillar VR6-B
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
105
AVRi trim to minimum counter clockwise. Volt/PF ctrl: AVR DCout bias = 0% VoltRegChar = POSITIVE Voltage range (-2V; 2V)
Caterpillar CDVR
Pin 44 on DVR – PF regulation directly from DVR is not connected.
AVRi trim to 50% Volt/PF ctrl: AVR DCout bias = 50% VoltRegChar = POSITIVE
Catterpillar DVR
Pin 44 on DVR – PF regulation directly from DVR is not connected.
AVRi trim to 25% Volt/PF ctrl: AVR DCout bias = 50% VoltRegChar = POSITIVE
AVK Newage MA330, 327, 321, 341
AVRi trim to minimum counter clockwise Volt/PF ctrl: AVR DCout bias = 50% VoltRegChar = POSITIVE
Newer Leroy Somer
Regulation signal +/- 0..2,5V
AVRi trim to minimum counter clockwise Volt/PF ctrl: AVR DCout bias = 50% VoltRegChar = POSITIVE
AVK Newage Cosimat N+
Volt/PF ctrl: AVR DCout bias = 25% VoltRegChar = NEGATIVE
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
106
Marathon DVR2000E
AVRi trim to 1/3 clockwise Volt/PF ctrl: AVR DCout bias = 50% VoltRegChar = POSITIVE
Marathon PM100, 200 Volt/PF ctrl:
AVRi+
AVRi-
18VACFrom generator
OUT1
iG-AVRi
TRANS
7
6
230/400VAC0VAC
AVRI COMAVRI OUT
OUT2
AVR DCout bias = 50% VoltRegChar = POSITIVE
MarelliMotori Mark I (M40FA640A/A) AVRi trim to 20%
AVRi+
AVRi-
18VACFrom generator
OUT2
OUT1
iG-
AVR
i
iG-AVRiTRANS
230/400VAC0VAC
AVRI COMAVRI OUT
68
Volt/PF ctrl: AVR DCout bias = 50% VoltRegChar = POSITIVE
MarelliMotori (M40FA610A)
iG-
AVR
i
Volt/PF ctrl: AVR DCout bias = 50% VoltRegChar = POSITIVE
KATO (KCR 360, 760) Volt/PF ctrl:
iG-
AVR
i
AVR DCout bias = 50% VoltRegChar = POSITIVE
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
107
Technical Data
Power supply Controller IS-Display IG-Display InteliVision 8 InteliVision 5
Voltage supply 8-36V DC 8-36V DC 8-36V DC 8-36V DC 8-36V DC Consumption depends on supply voltage
0,4A at 8VDC 0,3A at 8VDC 0,4A at 8VDC 1A at 8VDC 0.7 A at 8VDC
0,15 A at 24VDC
0,1 A at 24VDC
0,14 A at 24VDC
0,35A at 24VDC 0.55 A at 24VDC
0,1A at 36VDC
0,09A at 30VDC
0,12A at 30VDC
0,25A at 36VDC 0.45 A at 36VDC
Battery voltage measurement tolerance
2 % at 24V
RTC battery life-cycle
10 year
Hint: When internal RTC battery becomes flat, controller function (e.g. Ready for stand by) does not change until controller power supply is switched off. Some time before the battery is completely exhausted, a warning message appears in Alarmlist: "RTCbatteryFlat". After the next power switch on (with flat battery already) controller:
Stays in the INIT state (not possible to run genset) All History records disappear except of “System log: SetpointCS err” record Time and Date values are set to zero Statistics values are random
Operating conditions IS-NT** operating temperature -20..+70oC * IS-NT-BB operating temperature -40..+70oC * IG-NT-BB, IS-NTC-BB operating temperature -30 +70°C IG-NT-BB, IS-NTC-BB storage temperature -40 +80°C IS-NT*** operating temperature (LT version) -40..+70oC * Storage temperature -30..+80oC Storage temperature IS-NT-BB -40..+80oC Flash memory data retention time 10 years Protection front panel IP65 Humidity 95% without condensation IEC/EN 60068-2-30 Standard conformity Low Voltage Directive EN 61010-1:95 +A1:97 Electromagnetic Compatibility EN 50081-1:94 (EN 61000-6-3)
EN 50081-2:96 (EN 61000-6-4) EN 50082-1:99 (EN 61000-6-1)
EN 50082-2:97 (EN 61000-6-2) Vibration 5 - 25 Hz, ±1,6mm
25 - 100 Hz, a = 4 g Shocks a = 200 m/s2 Hint: * USB port should be used only above 0°C.
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
108
** IS-NT – including IS-Display and InteliVision 8 *** IS-NT – including IS-Display
Dimensions and weight Dimensions See Terminals and Dimensions chapter Weight (IG-NTC-BB) 950g
Mains and generator Nominal frequency 50-60Hz Frequency measurement tolerance 0,1Hz
Current inputs
IG-NT / IG-NT-BB IG-NTC / IG-NTC-BB / IS-NT-BB, IS-NTC-BB / IM-NT
Nominal input current (from CT) 5 A 1 A / 5 A Load (CT output impedance) < 0,1 Ω < 0,1 Ω CT input burden < 0,2 VA per phase (Inom=5A) < 0,1 VA per phase (Inom=1A)
< 0,2 VA per phase (Inom=5A) Max. measured current from CT 10 A 2 A / 10 A Current measurement tolerance 2% from the Nominal current 2% from the Nominal current Max. peak current from CT 150 A / 1s 150 A / 1s Max. short term current 12 A (for 30s) 2,4 A / 12 A (for 30s) Max. continuous current 5 A 1 A / 5 A
Voltage inputs – IG/IS-NT and modifications
IG-NT / IG-NT-BB IG-NTC / IG-NTC-BB / IS-NT-BB, IS-NTC-BB / IM-NT
Nominal voltage (ph-N / ph-ph) 277/480 VAC 120/207 or 277/480 VAC Maximal measured/allowed voltage
346/600 VAC 150/260 or 346/600 VAC
Input resistance 0,6 MΩ phase to phase 0,6 MΩ phase to phase 0,3 MΩ phase to neutral 0,3 MΩ phase to neutral Voltage measurement tolerance 1 % from the Nominal voltage 1 % from the Nominal voltage Over voltage class III / 2 (EN61010) III / 2 (EN61010) Hint: kW, kWh, Load sharing, VAr sharing measurement tolerance is 3%.
Binary inputs and outputs Binary inputs
IG-NT / IG-NTC / IG-NT-BB / IG-NTC-BB
IM-NT IS-NT-BB IS-NTC-BB
Number of inputs 12 6 16 Input resistance 4,7 kΩ 4,7 kΩ 4,7 kΩ Input range 0-36 VDC 0-36 VDC 0-36 VDC Switching voltage level for close contact indication
0-2 V 0-2 V 0-2 V
Max voltage level for open contact indication
8-36 V
8-36 V
8-36 V
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
109
Binary open collector outputs IG-NT / IG-NTC /
IG-NT-BB / IG-NTC-BB
IM-NT IS-NT-BB IS-NTC-BB
Number of outputs 12 6 16 Maximum current 0,5 A 0,5 A 0,5 A Maximum switching voltage
36 VDC 36 VDC 36 VDC
Analog inputs Not electrically separated Number of inputs 3 / 0 / 4 unipolar ( IG-NT(x), IG-NT(x)-BB/ IM-NT / IS-NT-BB,IS-NTC-BB ) Resolution 10 bits Jumper selectable range V, ohm, mA Maximal resistance range 2500 Ω Maximal voltage range 5 V Maximal current range 0 – 20 mA Input impedance 180 Ω for mA measuring Input impedance > 100 kΩ for V measuring Resistance measurement tolerance ± 2 % ± 2 Ω out of measured value Voltage measurement tolerance ± 1 % ± 1mV out of measured value Current measurement tolerance ± 1 % ± 0,5mA out of measured value
D+ function Max. D+ output current 300 mA Guaranteed level for signal Charging OK 80% of supply voltage
Speed pick-up input Type of sensor magnetic pick-up Minimum input voltage 2 Vpk-pk (from 4 Hz to 4 kHz) Maximum input voltage 50 Veff Minimum measured frequency 4 Hz Maximum measured frequency 10 kHz (min. input voltage 6Vpk-pk) Frequency measurement tolerance 0,2 %
Communication interface
RS232 interface Maximal distance 10m Speed up to 57.6kBd
RS485 interface Maximal distance 1000m Speed up to 57.6kBd
CAN bus interface Galvanically separated Maximal CAN bus length 200m Speed 250kBd Nominal impedance 120Ω
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
110
Cable type twisted pair (shielded) Following dynamic cable parameters are important especially for maximal 200 meters CAN bus length and 32 iS-COM units connected: Nominal Velocity of Propagation min. 75% (max. 4,4 ns/m) Wire crosscut min.0,25 mm2 Maximal attenuation (at 1 MHz) 2 dB / 100m Recommended Industrial Automation & Process Control Cables: BELDEN (see http://www.belden.com): 3082A DeviceBus for Allen-Bradley DeviceNet 3083A DeviceBus for Allen-Bradley DeviceNet 3086A DeviceBus for Honeywell SDS 3087A DeviceBus for Honeywell SDS 3084A DeviceBus for Allen-Bradley DeviceNet 3085A DeviceBus for Allen-Bradley DeviceNet 3105A Paired EIA Industrial RS485 cable LAPP CABLE (see http://www.lappcable.com) Unitronic BUS DeviceNet Trunk Cable Unitronic BUS DeviceNet Drop Cable Unitronic BUS CAN Unitronic-FD BUS P CAN UL/CSA
Analog outputs Speed governor output ± 10 V DC / 5 V PWM (500 – 3000Hz), max. 15 mA AVRi outputs PWM to IG-AVRi Current output 0 – 20 mA ± 0,3mA Voltage output 0 – 10 V DC, max. 15 mA Max load resistance 470R at 9,4V
IG-AVRi Power supply: 18V AC from IG-AVRi Trans/LV or IG-AVRi Trans/100 Absolutely maximum power supply range: 15 - 25 VAC Inputs: +AVR, -AVR (two wires, PWM from IG-CU) Outputs: OUT1, OUT2 floating (potential free) voltage source. AVRi output voltage range: potentiometer adjustable from +- 1V to +-10V DC. AVRi output current: max 15 mA. Mechanical dimensions: 96 x 27 x 43 mm , DIN rail (35 mm) mounted
IG-AVRi Trans/LV Primary voltage 1: 230-277 VAC Absolute low limit: 230 VAC – 20% Absolute high limit: 277 VAC + 20% Primary voltage 2: 400-480 VAC Absolute low limit: 400 VAC – 20% Absolute high limit: 480 VAC + 20% Frequency: 50 - 60 Hz Secondary voltage: 18 V AC, 5 VA Operating temperature -30..+70oC
IG-AVRi Trans/100 Primary voltage: 100 – 120 VAC
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
111
Absolute low limit: 100 VAC – 20% Absolute high limit: 120 VAC + 20% Frequency: 50 - 60 Hz Secondary voltage: 18 V AC Operating temperature -30..+70oC
IGS-PTM Voltage supply 8-36V DC Consumption 0,1A depend on supply voltage Mechanical dimensions: 40 x 95 x 45 mm , DIN rail (35 mm) mounted Interface to controller CAN Operating temperature -30..+70oC Binary inputs Number of inputs 8 Input resistance 4,7 kΩ Input range 0 - 36 VDC Switching voltage level for close contact indication 0 - 2 V Max voltage level for open contact indication 8-36 V
Binary open collector outputs Number of outputs 8 Maximum current 0,5 A Maximum switching voltage 36 VDC
Analog inputs Not electrically separated Number of inputs 4 Resolution 10 bits Maximal resistance range 0 – 250 Ω Maximal voltage range 0 – 100 mV Maximal current range 0 – 20 mA Resistance measurement tolerance 1 % ± 2 Ω out of measured value Voltage measurement tolerance 1,5 % ± 1mV out of measured value Current measurement tolerance 2,5 % ±0,5mA out of measured value
Analog output Not electrically separated Number of inputs 1 Resolution 10 bits Output range 0 to 20 mA ± 0,33 mA
IS-AIN8 Nominal power supply 24 VDC Power supply range 8 – 36 VDC Max. consumption 250 mA Mechanical dimensions: 150 x 160 x 50 mm ,
DIN rail (35 mm) mounted Connection to controller (galvanically separated) CAN1 Operating temperature -40..+70oC Storage temperature -40..+80oC Protection front panel IP 20 Humidity 95% without condensation
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
112
Standard conformity Low Voltage Directive EN 61010-1:95 +A1:97 Electromagnetic Compatibility EN 50081-1:94 (EN 61000-6-3)
EN 50081-2:96 (EN 61000-6-4) EN 50082-1:99 (EN 61000-6-1)
EN 50082-2:97 (EN 61000-6-2)
Analog inputs Nominal power supply 24 VDC Power supply range 8 – 36 VDC Number of inputs 8 Not galvanic separated Resolution 16 bits Each analog input can be software configured to: Measuring range Accuracy From to Resistance 0 Ω 2400 Ω ± 0,5 % 0 Ω 250 Ω ± 1,0 % Current Passive 0 / 4 mA 20 mA ± 0,5 % Active 4 mA 20 mA ± 0,5 % Active 0 mA ± 20 mA ± 0,5 % Voltage Thermocouples J, K, L type ± 0,2 % 0 mV 100 mV ± 0,2 % - 1000 mV + 1000 mV ± 0,5 % 0 mV 2500 mV ± 0,5 % Hint: Sensors must be isolated from the engine body (except for thermocouples (since HW version 5.0)). Follow rear sticker description and remove the appropriate jumpers in case of thermocouples not isolated from the engine body. It's possible to connect voltage up to 10V to an analog input if an external volt box which is described on p.53 is used.
I-AOUT8 Voltage supply 8-36V DC Consumption 0,1A depend on supply voltage Mechanical dimensions: 40 x 95 x 45 mm , 35 mm DIN rail mounted Interface to controller CAN Operating temperature -30..+70oC Number of analog outputs 8 (not electrically separated) Output range 0 to 10 VDC 0 to 20 mA PWM (1200 Hz)
IS-BIN16/8 Nominal power supply 24 VDC Power supply range 8 – 36 VDC Max. consumption 250 mA Mechanical dimensions: 150 x 160 x 50 mm ,
DIN rail (35 mm) mounted Connection to controller (galvanically separated) CAN1 Operating temperature -30..+70oC Storage temperature -40..+80oC Protection front panel IP 20
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
113
Humidity 95% without condensation Standard conformity Low Voltage Directive EN 61010-1:95 +A1:97 Electromagnetic Compatibility EN 50081-1:94 (EN 61000-6-3)
EN 50081-2:96 (EN 61000-6-4) EN 50082-1:99 (EN 61000-6-1)
EN 50082-2:97 (EN 61000-6-2) Binary inputs Galvanically separated two groups Number of inputs 8 + 8 Input resistance 3 kΩ Input voltage range 0-36 VDC Input voltage level for open contact 8 to Power supply VDC Input voltage level for close contact 0 to 2 VDC Voltage level is defined between Binary input and Binary input COM terminal.
Open collector outputs Number of outputs (galvanically separated) 8 Maximum current 0,5 A Maximum switching voltage 36 VDC
Frequency inputs Number of inputs 2 (RPM1, RPM2)
RPM1 Type of sensor magnetic pick-up Minimum input voltage 2 Vpk-pk (from 4 Hz to 4 kHz) Maximum input voltage 50 Veff Maximum measured frequency 8 kHz (min. input voltage 6Vpk-pk), frequency mode
RPM2 Type of sensor Contact or Active sensor Minimal pulse width 10 ms, integration mode Maximum measured frequency 60 Hz, integration mode Note: RPM1, RPM2 are available from IS SW version 2.6
IGL-RA15
Power supply Voltage supply 8-36V DC Consumption 0,35-0,1A (+1A max horn output)
Depend on supply voltage
Operating conditions Operating temperature -20..+70oC Storage temperature -30..+80oC Protection front panel IP65
Dimensions and weight Dimensions 180x120x55mm Weight 950g
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
114
Horn output Maximum current 1 A Maximum switching voltage 36 VDC
I-CB, I-CR
Power supply Voltage input 8-36V DC Consumption 0.1A depend on power supply
Operating conditions Operating temperature -20 ÷ +70 °C Storage temperature -30 ÷ +80 °C Humidity 85% without condensation Protection IP20
Dimensions and weight Dimensions 95x96x43 mm, DIN rail (35 mm) mounted Weight 300g
CAN bus interface Galvanic separated Maximal CAN bus length 200m Speed up to 250kBd (depends on ECU type connected) Nominal impedance 0Ω Cable type for iS connection sted pair (shielded)
RS232 interface Maximal distance 0m Speed p to 19.2kbps (depends on ECU type connected)
I-LB Voltage supply -36V DC Consumption ,1A depend on supply voltage Operating temperature -30..+70oC Mechanical dimensions: 5 x 96 x 43 mm , DIN rail (35 mm) mounted Interface to modem or PC S232, RS422, RS485, (USB – I-LB+ version) Interface to controller AN
IG-IB Voltage supply -36V DC Consumption ,1A depend on supply voltage Mechanical dimensions: 5 x 96 x 43 mm , DIN rail (35 mm) mounted Interface to controller S232 or CAN Interface to modem S232 Interface to Ethernet J45 (10baseT) Operating temperature -30..+70oC Storage temperature -30..+70oC
InteliGenNT, InteliGenNT-BB, InteliGenNTC-BB, InteliSysNT, InteliSysNTC-BB, InteliMainsNT, IGS-NT-2.6-Installation Guide.PDF, ©ComAp – November 2011
115
I-RBxx Number of relays: 6 or 8 in sockets Nominal voltage: 4 VDC Voltage range: 6,8 – 36 VDC Relay opens at: 0% of nominal voltage Electric / mechanic cycles: 00 000 / 10 000 000 Operating temperature range: 40°C to 70°C Maximal load: 6 A resistive load at 24VDC 4 A inductive load at 24 VDC (I-RBxx-231) 2 A at 231VAC Contacts protection: aristor 14DK390
IG-MTU Primary voltage Ph-Ph x400 VAC / 50Hz (3x480 VAC / 60 Hz) Secondary voltage Ph-N x 230 V AC ( 3x277 VAC / 60 Hz) , 5 VA Mechanical dimensions: 5 x 95 x 60 mm , DIN rail (35 mm) mounted Primary/secondary Phase shift 1° Operating temperature -30..+70oC
IG-MTU-2-1 Primary voltage Ph-Ph x600 VAC / 50Hz (3x720 VAC / 60 Hz) Secondary voltage Ph-N x 173 V AC ( 3x208 VAC / 60 Hz) , 5 VA Mechanical dimensions: 55 x 95 x 60 mm , DIN rail (35 mm) mounted Primary/secondary Phase shift 1° Operating temperature -30..+70oC