clown in a barrel i e ltr
TRANSCRIPT
http://www.canon.com/c-park/
* Push and pull the lever on the right. The barrels begin rolling back and forth and merry acrobat of clowns starts.
Assembly Instructions
Mountain fold(dotted line)Make a mountain fold.
Valley fold(dashed and dotted line)Make a valley fold.
Scissors line(solid line)Cut along the line.
Cut in line(solid line)Cut along the line.
Glue spot(Red dot)Glue parts with the same number together.
Glue spot(Green dot)Glue within the same part.
Glue spot(Blue dot)Glue to the rear of the other part.
GlueThe glue spot(colored dot)shows where to apply the glue.
Tools and materials
Assembly tip
Caution
Scissors, set square, glue(We recommend stick glue), pencil, usedballpoint pen, toothpicks, tweezers, (useful for handling small parts)
Before gluing, crease the paper along mountain fold and valley fold lines and make sure rounded sections are nice and stiff.
Glue, scissors and other tools may be dangerous to young children so be sure to keep them out of the reach of young children.
View of completed model
Assembly Instructions : Twelve US letter sheets (No. 1 to No. 12)
*Hint: Trace along the folds with a ruler and an exhausted pen (no ink) to get a sharper, easier fold.
* Build the model by carefully reading the Assembly Instructions , in the parts sheet page order.
Before starting assembly : Writing the number of each section on its back side before cutting out the sections is highly recommended.(* This way, you can be sure which section is which even after cutting out the sections.)
Indicates where sections should be glued together.
Indicates the order for assembling parts.
Indicates where to insert sections. Do not glue the sections together.
Round bar : Use to give parts a curved surface.
Tweezers : Useful in working with fine parts.
Be sure to build this model carefully.
Caution : Spread glue in a thin, even layer before gluing surfaces together.
Make two sets.
(Moving) Clown in a barrel : Assembly Instructions
(Moving) Clown in a barrel : Assembly Instructions
Prepare part 8 in the same way.
Firmly form the shape as you glue to prevent distortion.
Parts 5 to 9
(Moving) Clown in a barrel : Assembly Instructions
Before you glue the parts, arch the barrel parts with a round bar.
Parts 11 and 12
(Moving) Clown in a barrel : Assembly Instructions
Caution : Spread glue in a thin, even layer before gluing surfaces together.
(Moving) Clown in a barrel : Assembly Instructions
Caution : Make sure the direction of the barrel is correct.
Caution : Make sure the direction of Part 2 is correct before you glue it.
Parts 11 and 12
Parts 5 to 9
The hexagonal pasting margin comes to the front.
Turn the entire body over and insert the part 1.*It will be easier to work if you use 2 empty boxes on the left and right as supports.
(Moving) Clown in a barrel : Assembly Instructions
Parts 22 and 23
Parts 22 to 24
(Moving) Clown in a barrel : Assembly Instructions
Parts 3 and 13
Parts 3 and 13
Parts 22 to 24
(Moving) Clown in a barrel : Assembly Instructions
Parts 25 to 26
Slowly push and pull the lever to check the movement of the 2 barrels.
Glue the 8 corners of the top sheet (Part 19).
Next, glue Part 31.
(Moving) Clown in a barrel : Assembly Instructions
When you assemble the base, work carefully on a flat surface to prevent distortion.
First, put a lever through the hole in Part 28 and glue it, and then glue Part 29.
(Moving) Clown in a barrel : Assembly Instructions
Form the shape to prevent distortion and glue both arms
Arm part
Hand part
Head part
Torso and leg part
Before you glue them, arch the torso and leg parts with a round bar.
(Moving) Clown in a barrel : Assembly Instructions
Form the shape to prevent distortion and glue.
(Moving) Clown in a barrel : Assembly Instructions
Make two sets.
Prepare parts 33,34,35 in the same way.
Finished!