city of tamarac comprehensive master identity campaign

notes

City of TamaracComprehensive Master IdentityCampaign

drawing: T-1

City of Tamarac Comprehensive Master Identity CampaignKey:

Section 1: General specifications and criteria for manufacturing and installation Pages T2 - T4

Section 2: Electronic Message Center Specifications for Type EMC Signage Pages T4 - T5

Section 3: Work Sheets and related bid information Page T6

Section 4: Color Palette Selections for Non-illuminated (NI) and Illuminated (IL) Pages T7-T10

Section 5: Fabrication Specifications for Type T1 Signage Type T1-NI Pages T11 - T16 Type T1-IL

Section 6: FDOT 2015 Design Standards for Single / Cantilevered Ground Signs Pages T-17 - T18

Section 7: Fabrication Specifications for Type T2 Signage Type T2-NI Pages T19 - T20 Type T2-IL

Section 8: Fabrication Specifications for Type P1 Signage Pages T-21 - T22 Type P1-NI Type P1-IL-EMC

Section 9: Fabrication Specifications for Type P2 Signage Pages T23 - T24 Type P2-IL-EMC Single Face Type P2-IL-EMC Double Face

Section 10: Fabrication Specifications for Municipal Complex Signage Page T25 Type MC-IL-EMC

Section 11: Fabrication Specifications for Community Center Signage Page T26 Type CC-IL-EMC

Section 12: Fabrication Specifications for Residential Identity Signage Pages T27 - T29 Type RD-NI Type RD-IL-EMC

Section 13: Fabrication Specifications for Type D Directional Signage Pages T30 - T32 Type DIR-1- Dedicated Post Mount Type DIR-2- Existing Post Mount

project: Identity Branding

date: 03/31/15

scope of work: General Specifications

06 24 2105

notes


drawing: T-2

ALUMINUM:1) All aluminum shall conform to aluminum specifications ofhardness and dimensional tolerances.

2) Aluminum sheet and plate shall conform to ASTM B 209, Alloy 5000series for painted finish.

3) Extruded aluminum shall be Alloy 6063-T5.

4) Unless otherwise specifically approved in writing by the client representative,furnish exact sections, weights and kinds of material specified, using details anddimensions shown. Not all connections are detailed: similar details apply to similar conditions, unless otherwise indicated. Contact the City of Tamaracrepresentative promptly to verify design of members or connections in any situation where design requirements are unclear.

5) Establish that joint welding procedures are pre-qualified or tested in accordancewith American Welding Society (AWS) qualification procedures.

6) Welders must currently be certified under American Welding Society (AWS)qualification standards.

7) Materials provided shall be free of surface blemishes such as pitting, roller marks,rolled trade names and surface roughness. Edges that are either joined or formedby Braking are to be crisp and sharp and finished in accordance with AluminumAssociation Specifications.

STRUCTURAL STEEL:

1) Fabrication and erection of structural steel framing members shall be in accordance with the latest edition of the AISC “Code of Standard Practice forSteel Buildings and Bridges.”

2) Unless otherwise specifically approved in writing by the client representative,furnish exact sections, weights and kinds of material specified, using details anddimensions shown. Not all connections are detailed: similar details apply to similar conditions, unless otherwise indicated. Contact the City of Tamaracrepresentative promptly to verify design of members or connections in any situation where design requirements are unclear.

3) Establish that joint welding procedures are pre-qualified or tested in accordancewith American Welding Society (AWS) qualification procedures.

4) Welders must currently be certified under American Welding Society (AWS)qualification standards.

5) Steel shall be delivered in timely fashion, to permit most efficient and economical flow of work. Deliver anchor bolts, washers and other anchoragedevices in time to avoid delays and permit their proper installation.

6) Protect steel and other materials from damage and corrosion.

7) Structural steel members shall conform to ASTM A 36. Steel pipe columnsshall conform to ASTM A 53.

8) Galvanized anchor bolts shall conform to ASTM A 307. Carbon steel, Grade C.Galvanized steel plate washers and nuts shall conform to ASTM A 36.

9) High strength structural bolts shall conform to ASTM A 325, with matchingASTM A 563 nuts and ASTM F 436 washers.

10) Carbon steel nuts and bolts shall conform to ASTM A 307. Provide hexagonalbolt heads and nuts at all exposed locations.

11) Welding electrodes and fluxes shall conform to ASTM Standards for all applications.

12) Shop fabricate and assemble to maximum degree possible in compliance with requirements of AISC specifications. Cut, fit and assemble units with exposed surfaces smooth, square and free from cutting marks, shear distortion,burrs and nicks. Tolerances shall be as specified in AISC code unless more stringent requirements are indicated on the drawings. Perform thermal cuttingby machine, to greatest extent possible. Plain thermally cut edges which are tobe welded.

13) Comply with requirements of AWS code for welding procedures and qualityof welds, including appearance. For built up sections, assemble components andweld using procedures which will maintain proper alignment of finished section.Verify that weld sizes, fabrication sequence and equipment to be employed willlimit distortions to allowable tolerances. Surface bleed of back side welding onexposed surfaces will not be acceptable. Grind smooth exposed fillet weld½ inch and larger. Grind flush all butt welds. Dress all exposed welds. Removeall weld splatter “dingle berries” for a smooth surface.

14) Accurately mill ends of columns and other members which must transmitloads in bearing. Make all holes in steel members by means of cutting, drilling orpunching at right angles to surface of metal. Do not make or enlarge holes byburning. Provide holes in steel members as required to permit connection ofwork by others.

15) Erect structural steel in compliance with AISC code and specificationsdealing with architecturally exposed structural steel. Set structural membersaccurately to locations and elevations indicated, with tolerances established inAISC code, before making final connections. Do not use thermal cutting to correctfabrication errors on any major structural member.

16) Clean bearing and contact surfaces before assembly. Slightly roughen concrete and masonry surfaces to improve bond. Set base and bearing platesaccurately, using metal wedges, shims or setting nuts as required. Aftertightening anchor bolts and ensuring that structure is plumb, grout solidly between plates and bearing surfaces. Comply with manufacturer’sinstructions for non-shrink grout.

17) Use high strength bolts which comply with requirements of AISC “Specification for Structural Joints Using ASTM A 325 or A 490 Bolts.”

18) Do not perform welding when surfaces are wet, or exposed to rain or highwind. Perform field welding in accordance with AWS “Structural Welding Steel.”Tighten and leave in place erection bolts used in field welded construction.Verify that weld sizes, erection sequence and equipment to be employed willlimit distortions to allowable tolerances. Touch up all field welds with primer andfinish coat in accordance with paint specification section.

GRAPHICS:

1) Contractor shall be responsible for coordination of the graphics and signagewith the City of Tamarac and other sub contractors and trades people relative tothis work. These coordination efforts will include, but not be limited to, deliveries,work schedules and installation. Storage space at city facilities is limited and willalso require coordination and or approval of finished work stored at the city facility. Any finished work stored at the city facility without prior permission will berelocated at contractors expense.

2) Finished digital artwork for all symbols and other custom designed graphic components, such as logos, logo type and arrow heads used for all sign types shallbe furnished or specified by the City/Designer for reproduction. All enlarging andreducing is the responsibility of the sign contractor.


date: 03/31/15


notes


drawing: T-3

GRAPHICS: (continued)

3) Problems such as messages being too long to fit into the required formats, difficult logo or logo type components to reproduce accurately,etc., must be brought to the attention of the designer, prior to execution.It is required that the sign contractor not resolve these kinds ofdiscrepancies on their own.

4) All graphic designs created by the Designer and/or the City for thisproject are to be used exclusively for this project. The sign contractormust receive express written permission from both the Designer and theCity for any use other than for the completion of this project, includingself promotion and publication.

5) All work shall be complete in every respect and satisfactory to allgoverning legislative authorities, building codes and the City/Designer.

6) Three (3) sets of detailed shop drawings (plans, elevations and scaleddrawings) are to be submitted to the Designer for review prior to production. These drawings are to show/indicate all materials, finishes,construction details, lighting, and installation detailing of art work andsignage structure, including locations of all material seams both finishedand unfinished. Additional drawings may be requested by the Designer,at the contractors expense, to further indicate items in question.

7) Contractor shall, within 5 days of contract execution, provide City representatives with a list of electrical requirements for each element.

8) All products used in the fabrication, joining, finishing or other procedures necessary in the execution of the work shall be used accordingto the manufactures instructions for the use of such products. Design ofinternal structure, mounting assemblies and connections are by SignContractor. Sign Contractor shall submit three (3) sets of comprehensiveshop drawings incorporating typical mounting structures for all signcomponents given site conditions.

9) Submit four (4) 3” x 5” samples of all actual material to be used for eachdifferent finish surface, (each color and texture) coated to match the proper color texture and finish as for each indicated, to show the quality of fabrication and design.

10) Shop fabricate, assemble and finish to maximum degree possible.Contractor will adhere to all details and dimensions on drawings withoutdeviation. Cut, fit and assemble units with exposed surfaces smooth, square and free from cutting marks, shear distortion, burrs, nicks and sharp corners.

11) There shall be no visible seams or fasteners. All joints and connectionsshall be finished flush, true and smooth without defects. Finish welds onexposed surfaces and spot welds shall be imperceptible in the finishedwork. No gaps, light leaks, oil canning or waviness will be acceptable.

12) Except where indicated otherwise, finish all surfaces smooth.

13) All flat metal sign facing and cladding to be aluminum unless otherwiseindicated, and shall be free from pitting, warping, waviness, bulges, oilcanning or other physical deformities. Minimum material thickness shallbe .125 inches or as indicated in drawings. Internal support structureshall be rust proof treated steel or aluminum, as indicated. Where steel andaluminum (dissimilar metals) meet, the metals shall be materially isolatedto prevent electrolytic reaction.

14) Letterforms, logos, patterns and other graphics shall be cut/applied true to artwork/typeface and have clean edges andcorners. Letter forms having rounded positive or negative corners,nicked, cut or ragged edges will not be acceptable. Letter formsshall be aligned to maintain a baseline parallel to the sign formatand margins shall be maintained as per the design documents.

15) Internally illuminated signs shall be illuminated using fixturesand lighting as specified in design documents. There shall be no“Hot Spots” or shadows and light distribution shall be uniform andeven. All illuminated signs shall be free of light leaks and all ventingshall be light baffled as required. Exterior illumination, if required,must be outdoor, weather proof fixtures, lamps and ballasts/transformers. Sign contractor to provide the City/Designer withcomplete lighting replacement information including brand, type,wattage, color, etc. for all lighted components. This informationshall be in type written format 8 ½” x 11”.

16) All illuminated signs shall have access to their interiors for re-lamping and maintenance. Such service panels shall be concealed,tight fitting, light proof and water proof, flush with adjacent surfacesand secured against vandalism. Contractor to supply 5% attic stockof all lighting used.

17) All illuminated signs shall use UL approved and listed / labeledcomponents and the completed sign must bear the UL label.All transformers and electrical hardware shall be concealed, non audible and non-visible to pedestrian and vehicular traffic.

18) Provide disconnect switches for all Illuminated signs in accordancewith FBC / NEC electrical code requirements. Locate disconnect switcheson or in signs so they are not easily visible to the public.

19) All Fabricator or other labels on all signs shall be concealed fromview, with the exception of UL labels.

20) Installation of all elements shall be the responsibility of the contractor. Contractor will be responsible for any damage caused tothe site or adjacent objects or elements during installation. Contractor shall be responsible for cleaning up all work areas uponthe completion of their work on a daily basis. Sign Contractor toprovide to the Designer and the City, a complete finish / componentcare instruction manual as specified by the manufacturers for on-goingcosmetic sign cleaning and maintenance.

1) All metal surfaces to be painted with acrylic linear polyurethaneenamel as manufactured by Matthews Paint Company, or equal,to match colors as specified. Two components, acrylic aliphatic isocyanate / acrylic polyurethane are formatted with ultraviolet (UV)inhibitors and are engineered for exterior graphics and signage components.

2) All steel and aluminum surfaces shall be properly treated and primedas required, using Matthews or equal pretreatment. Primer and finishpaint system. Primer and finish paint system must be approved bythe City of Tamarac representative prior to application.All paint finishes shall be guaranteed free from chalking, discoloration,fading or any other defect for a period of five (5) years.Contractor shall be responsible for protecting the finish during and after installation.

INSPECTIONS:

1) Inspections shall be performed in accordance with the applicablelocal building codes and by a registered building inspector. Allinspections to be coordinated by the Sign Contractor. Inspections orpermit requirements shall be required for the following types of work:

A. Foundation work

B. Re-bar placement and all concrete construction

C. All Electrical work

D. All FDOT related work

2) Engineering for all the elements shall be submitted to the designerand the City of Tamarac at the time of the shop drawing submittal.All engineering submittals must be sealed and stamped by a FloridaLicensed Structural Engineer.

WORKING HOURS:

1) Project work hours for installation shall be between the hours of7 A.M. EST and 7 P.M. EST and shall not impede in any way with thenormal traffic flow and patterns for product installed in /on city/county ROWs

2) All site work schedules shall be submitted to the City of Tamaracrepresentative, in writing, for approval prior to beginning theinstallation work required. Failure to do so may result in denied access.

PAINT & FINISHES:


date: 03/31/15


GENERAL NOTES:

1) All materials and workmanship shall conform to the most recentedition of the FBC /NEC. All work shall be performed to the highestdegree of professional standards and shall be free of imperfectionsin material and workmanship and be suitable for its intended useand location.The contractor shall have broad knowledge, diverse shop and fieldexperience, flexibility, coordination ability, skilled craftsmen and physical plant necessary to produce quality products equivalent toor superior to similar type products produced by other contractorsin the same area of expertise.It is intended that all finished work be of the highest quality to passeye-level examination and scrutiny by the City of Tamarac and it’srepresentatives. Contractor shall be responsible for all foundations,structural and electrical engineering, compliance with all applicablelocal, state, FDOT and national codes and inspections.

2) Specific notes and details on drawings shall take precedence overgeneral notes and typical details.

3) Design Loads: All elements shall be engineered to withstand windload requirements as specified by all applicable wind load zones forState building codes.

4) The contract structural drawings and specifications represent thefinished structure unless otherwise shown. They do not indicate themethod of construction, nor the details of fabrication required forthe complete structural integrity of the elements nor do theyrepresent the considerations of the preferred shop practices of theindividual contractors therefore it shall be the responsibility of thecontractor to perform the complete structural design of the elementsall reasonable safety factors necessary to protect the City and it’srepresentatives against public liability.

5) All work must be performed in accordance with all Federal, Stateand Local Safety Laws.

6) Contractor shall provide three (3) sets of shop drawings to the Cityand it’s representatives for approval, including required engineering,which shall be sealed by a Florida registered and licensed structuralengineer. All signs and / or design elements shall be reviewed and approved by the City and it’s representatives. Contractor shallincorporate all modifications and corrections to the shop drawings and resubmit for approval. Upon approval of shop drawings, contractorshall proceed with the required submittals. Work shall not commenceuntil submittals have been approved and the contractor receiveswritten authorization to proceed from the City of Tamarac.

notes


drawing: T-4


date: 03/31/15


TIME & SCHEDULE:

1) Contractor shall submit a detailed working schedule. This detailed scheduleshall show all time lines indicating the start and completion dates for shop drawings, submittals, permits, fabrication, shipping and installation. Contracttime schedule must be submitted with the signed contract documents to be part of the record of transaction.

SPECIALTY PRODUCTS:

1) LED LightingLED Lighting shall be AGILIGHT PRO 160 LED 6500K White Specifications LIGHT OUTPUT 160 lm per foot (@ 6500K) LIGHT PATTERN batwing beam pattern INPUT VOLTAGE 12V DC MODULE CURRENT 0.075A MODULE WATTAGE 0.9W (max. 0.95W) 60W Power Supply Loading 60 modules DIMENSIONS 3.33" x 0.80" x 0.44" (85 mm x 20 mm x 11 mm) INGRESS PROTECTION IP68 rated OPERATING TEMPERATURE -40°C to +60°C L70 LIFETIME 50,000 hours Population Density Guide PRO 160 LED Module STANDARD (inch) CHANNEL DEPTH 3” MULTIPLE ROWS ROW SPACING 8

AGILIGHT Brand LED 60W Power SupplyAGILIGHT Brand PRO 160 LED 6500K White

2) LED Power Supply:Agilight LED 60W Power Supply with built-in weathercompartments for wiring enclosures.Does not require a transformer box

Specifications INPUT VOLTAGE 100-277V AC Max Output Power 60W Output Voltage 12V DC Typical Efficiency 87% IP Rating IP68 OPERATING TEMPERATURE -35°C to +60°C DIMENSIONS 10.98" × 3.23" × 2.03" Population Density Guide Features and Benefits 2) LED Power Supply:Agilight LED 60W Power Supply with built-in weathercompartments for wiring enclosures.Does not require a transformer box

notes


drawing: T-5


date: 03/31/15

scope of work: General / EMC Specifications

Electronic Message Centers: ContinuedAll Electronic Message Centers (EMC) provided by Watchfire by Time-O-Matic1015 Maple StreetDanville, IL 61832Reference: Job Site Name: City Of Tamarac

All units to be front vented, flush mounted to fabricatedsign displays.Options include C. Amber 19MM EMC with broadband wireless data link to City of Tamarac network source.

Options include the following specifications:

Amber and Full Color RGB EMC at sizes and sign types as noted

STANDARD FEATURESColor: LED RGBColor Capability: 1.15 QuintillionViewing Angles: 140 Horiz/70 VertVideo: plays prerecorded clips up to30FPS;Imports Windows Video(AVI);Animated Text & graphicsIncludes:Brightness: Day 10,000 NITs ;Night 750 NITsIgnite Graphics SoftwarePRODUCT SPECIFICATIONSCabinet Size:Pixel Pitch W19mm Color41in H x 6ft 3in L x 5in DCabinet Style: Double Face Twinpak (Slim)Character Size: 6 lines / 19 Characters at a 5" type.Approx. Weight: 518 Lbs.Warranty: Standard 5 Year Watchfire warranty applies.Electrical Service:120.00 VOLT 6.00 amps per face / 12.00amps total Single Phase Service Refer tothe Installation manual for details onwiring. Based on 18.00 hours of operation aday, plus or minus 10% depending on howthe sign is programmed.Example: 7.5 KWHrs a day x $0.07 = 0.53/Day

Pixel Matrix: 48 X 96Viewing Area: 36in H x 6ft LCommunications: Broadband Wireless With 1 Year Data PlanGroup Link: Not OrderedTemperature Sensor: w/100-Step Photocell w/15 ft CableSoftware Training: Web Based Software TrainingPersonal Computer: Ignite IncludedFiber Optic Cable: Not RequiredCabinet Separation: Standard Up To 15 FeetPower Requirements: Standard As QuotedSign Mounting Kit: Not RequiredSpare Parts Kit: OptionalWebcam: Optional

STANDARD FEATURESColor: LED AmberColor Capability: 4096 shadesViewing Angles: 90 Horizontal/40 VerticalVideo: Plays prerecorded clips up to 30FPS;Animated Text & graphicsIncludes:Brightness: Daytime 5000 NITs ; Nighttime 500 NITsIgnite Graphics SoftwarePRODUCT SPECIFICATIONSCabinet Size:Pixel Pitch Mono19mm Amber17in H x 10ft 3in L x 5in DCabinet Style: Double Face Twinpak (Slim)Character Size: 2 lines / 32 Characters at a 5" type.Approx. Weight: 384 Lbs.Warranty: Standard 5 Year Watchfire warranty applies.Electrical Service:120.00 VOLT 2.00 amps per face / 4.00amps total Single Phase Service Refer tothe Installation manual for details onwiring. Based on 18.00 hours of operation aday, plus or minus 10% depending on howthe sign is programmed.Example: 2.5 KWHrs a day x $0.07 = 0.18/DayPixel Matrix: 16 X 160Viewing Area: 12in H x 10ft L

Communications: Broadband Wireless With 1 Year DataPlanGroup Link: Not OrderedTemperature Sensor: w/100-Step Photocell w/15 ft CableSoftware Training: Web Based Software TrainingPersonal Computer: PC Not ordered. Ignite IncludedFiber Optic Cable: Not Ordered / Not RequiredCabinet Separation: Standard Up To 15 FeetPower Requirements: Standard As QuotedSign Mounting Kit: Not Ordered / Not RequiredSpare Parts Kit: Not OrderedWebcam: Not OrderedCustom Artwork Pkg: Not OrderedTechnician On-Site: Not OrderedOPTIONSSpecial Options: Not Ordered

STANDARD FEATURESColor: LED AmberColor Capability: 4096 shadesViewing Angles: 90 Horizontal/40 VerticalVideo: Plays prerecorded clips up to 30FPS;Animated Text & graphicsIncludes:Brightness: Daytime 5000 NITs ; Nighttime 500 NITsIgnite Graphics SoftwarePRODUCT SPECIFICATIONSCabinet Size:Pixel Pitch Mono19mm Amber17in H x 39in L x 5in DCabinet Style: Double Face Twinpak (Slim)Character Size: 2 lines / 10 Characters at a 5" type.Approx. Weight: 190 Lbs.Warranty: Standard 5 Year Watchfire warranty applies.Electrical Service:120.00 VOLT 1.00 amps per face / 2.00amps total Single Phase Service Refer tothe Installation manual for details onwiring. Based on 18.00 hours of operation aday, plus or minus 10% depending on howthe sign is programmed.Example: 1.2 KWHrs a day x $0.07 = 0.08/DayPixel Matrix: 16 X 48Viewing Area: 12in H x 36in LCommunications: Broadband Wireless With 1 Year DataPlanGroup Link: Not OrderedTemperature Sensor: w/100-Step Photocell w/15 ft CableSoftware Training: Web Based Software TrainingPersonal Computer: PC Not ordered. Ignite IncludedFiber Optic Cable: Not Ordered / Not RequiredCabinet Separation: Standard Up To 15 FeetPower Requirements: Standard As QuotedSign Mounting Kit: Not Ordered / Not RequiredSpare Parts Kit: Not OrderedWebcam: Not OrderedCustom Artwork Pkg: Not OrderedTechnician On-Site: Not OrderedOPTIONSSpecial Options: Not Ordered

STANDARD FEATURESColor: LED AmberColor Capability: 4096 shadesViewing Angles: 90 Horizontal/40 VerticalVideo: Plays prerecorded clips up to 30FPS;Animated Text & graphicsIncludes:Brightness: Daytime 5000 NITs ; Nighttime 500 NITsIgnite Graphics SoftwarePRODUCT SPECIFICATIONSCabinet Size:Pixel Pitch Mono19mm Amber41in H x 6ft 3in L x 5in DCabinet Style: Double Face Twinpak (Slim)Character Size: 6 lines / 19 Characters at a 5" type.Approx. Weight: 518 Lbs.Warranty: Standard 5 Year Watchfire warranty applies.Electrical Service:120.00 VOLT 4.00 amps per face / 8.00amps total Single Phase Service Refer tothe Installation manual for details onwiring. Based on 18.00 hours of operation aday, plus or minus 10% depending on howthe sign is programmed.Example: 5 KWHrs a day x $0.07 = 0.35/DayPixel Matrix: 48x96Viewing Area:36in H x 6ft L

Communications: Broadband Wireless With 1 Year DataPlanGroup Link: Not requiredTemperature Sensor: w/100-Step Photocell w/15 ft CableSoftware Training: Web Based Software TrainingPersonal Computer: PC Not ordered. Ignite IncludedFiber Optic Cable: Not RequiredCabinet Separation: Standard Up To 15 FeetPower Requirements: Standard As QuotedSign Mounting Kit: Not RequiredSpare Parts Kit: Not OrderedWebcam: Not OrderedCustom Artwork Pkg: Not OrderedTechnician On-Site: Not Ordered

Amber EMC Spec for T-2 and P2 DisplaysAmber EMC Spec for P1 DisplaysAmber EMC Spec for MC /CC Displays Full Color RGB EMC Spec for MC /CC Displays

notes


drawing: T-6


date: 03/31/15

scope of work: Work Sheet

Bid Work Sheet

1) It will be the responsibility of the bidder(s) to preview all site conditions andbe familiar with all aspects of the project. It is expected that the bidder(s) willinclude any contingencies and provisions for mobilization, staff time forpermits and approvals, project management and inspections / permits.

2. All City of Tamarac provisions in the RFP will take presidency over provisionsas set forth in the Simmons Design Group documents.

3. The City of Tamarac will accept approved alternates for LED internal lighting of proposed identity displays.

Bid Specifications: Work Sheet Layout is based on a starting base bid for a non-illuminated single face display (NI) with an additional cost for illumination (IL), an additional cost for Electronic Message Center (EMC), additional cost for double face (DF)

Bid Breakdown based on Site Mapping Type T1 Signage / Type T2 Signage Bid Breakdown based on Site Mapping Park Type P1 Signage / Type P2 Signage

Location 1: Type T1 NI IL


Location 3: Type T1 NI IL IL DF


Location 5: Type T2 IL EMC






Location 11: Type T2 V-Shape* IL EMC

Location 12A: Type T1 IL



Location 12B: Type T2 IL EMC

OPTION 1 OPTION 2 OPTION 3 Non-Illuminated Illuminated EMC

Location 1: Type P1

Location 2: Type P1

Location 3: Type P1

Location 4A: Type P1

Location 6: Type P2


Location 4B: Type P1


Location 7C: Type P1

Location 8: Type P2



Location 10: Type P2

Location 11: Type P2

Illuminated EMC

Location 5B: Type CC

Location 5A: Type MC IL EMC AMBER OPTION

IL EMC AMBER OPTION

Bid Breakdown based on Site Mapping: Specialty Type MC Signage / Type CC Signage

4. The City of Tamarac will accept approved alternates for EMC (Electronic Message Centers)for the proposed identity displays in which EMC’s are proposed.

5. The City of Tamarac will supply electrical source conduit and electrical feed to each locationin a state that allows for a proper electrical connection by authorized, licensed and qualifiedelectrical contractor. Sign Contractor responsible for electrical hook up to City suppliedelectrical sources.6. All fabricated, supplied products, electrical / electronic components and sub assembliesmust be warrantied against all product failure, fade and deterioration for a period offive (5) years. Extended warranties and service agreements should be included forconsideration by the City of Tamarac.

$______ $______

$______

$______

$______

$______

$______

$______

$______

$______

$______

$______

$______

$______ $______

$______

$______ $______

$______

$______

$______

$______

$______

$______

$______

$______

$______

$______

$______

$______

IL V Shape $______

NI IL

NI IL

NI IL IL DF

NI IL

IL EMC

IL

IL

IL

NI IL

IL EMC

IL

IL

IL

IL EMC

$______ $______

$______

$______

$______

$______

$______

$______

$______

$______

$______ $______

$______

$______

$______

$______

$______

$______

$______

$______

$______

$______

$______

IL DF$______

EMC $______

EMC $______

IL DF $______

IL DF $______

IL DF $______

EMC $______

EMC $______ IL DF$______

IL DF$______

Double Face / IL

$______

$______

EMC RGB FULL COLOR OPTION

EMC RGB FULL COLOR OPTION

$______

$______

TOTAL / DF $______

TOTAL / DF $______

Type RD-NI Single Face Option $____________ Double Face Option $______________ V-Shape Configuration $__________________

Bid Breakdown based on Pre-Determined Locations: Specialty Type RD-NI Signage / Type RD-IL Signage Bid Pricing based on a quantity of 3 Single Face, 3 Double Face and 2 V-Shape Displays

Type RD-IL Single Face Option $____________ Double Face Option $______________ V-Shape Configuration $__________________

7. Unless otherwise specified or directed, Sign Contractorwill be responsible to remove existing signage at grade.Below grade foundations will remain.

8. The City of Tamarac reserves the right to change /alterquantities shown within the bid and site mapping documentsas needed / required. All pricing will be considered to be bidon a “quantity” basic and pricing will remain un-changed regardlessof final quantity / option selection.

IL DF $______

NI $______

EMC $______

IL DF $______

IL DF$______

Single Face / IL*Single Face / NI*

Includes EMC additional Unitin Double Face Cost

OPTION 1 OPTION 2 OPTION 3 Non-Illuminated Illuminated EMC

Double Face / IL

Single Face / IL*Single Face / NI*

Includes EMC additional Unitin Double Face Cost

notes


drawing: T-7


date: 03/31/15

scope of work: Color Palette Specifications

1. .250 aluminum computer routed ribbon shape (1A) welded to 2”x2” x.125” aluminum square tube armature (1B) and .090 aluminum machine formed mounting tray (1C).

2. 3M 680-10 White reflective cut shape with clear custom digital UV stable inks in approved PMS color program. 3M 8914 Optically Clear over- laminent over printed surface.

3. Fabricated column feature from 2”x2”x.125” (3A) square aluminum tube with decorative capital. Decorative capital features a 1” x1” aluminum tube bottom collar (3B), .080 aluminum curved filler(3C) with 1.5”x1.5” aluminum tube top cap.(3D) .090 aluminum top cover. (3E) 2”x2” tube construction includes a .080 aluminum inner baffle (3F) to house Texture Plus simulated stone material. MPC 113SP textured finish in approved color palette.

6. Main Message Panels from .090 aluminum sheet (6A) with 90 degree machine formed returns to join panels. Panels secured to support posts with bent .090 (6B) aluminum inner shapes, through bolted as required. Message Panels secured to inner .090 aluminum shapes with #8 flat head fasteners, as required. Upper portion of Ribbon shape finished MPC Gloss Black with lower portion finished in approved color palette selections. Horizontal square tube band and lower portion of panel finished with MPC 287-113SP Course textured additive to satin finished acrylic polyurethane coatings.

7. Horizontal 1.5”x1.5” x.125” aluminum square tube band, capped end with .090 aluminum, blind mounted from behind with #8 flat head SS fasteners. MPC 113SP textured finish in approved color palette.

8. FDOT 2015 Approved Design Standards multi-directional break-away post base assembly with 4” OD schedule 40 aluminum round support posts. 9. Below grade embedment of support posts in accordance with FDOT approved practices and specifications with Florida Registered Structural Engineer calculations and documentation/Seal

4. Nominal 13/8” thick Stacked “Kurastone”Stone column inset material from Nichiha. Material cut and secured into column baffles with high-bond adhesive mastic and blind fasteners. www.nichiha.com 866-424-4421

5. .250” computer routed aluminum plate graphics (5A) blind mounted flush to aluminum background panel. Graphics finished gloss MAP Black with 3M 680-85 Black reflective message applied to .250” aluminum plate graphics. Typical: Front face only. Back face to receive 3M 680-85 (5B)Black reflective message applied directly to face of background panel.

Welcome to

The City For Your LifeTAMARACWelcome to

The City For Your LifeTAMARAC

Thank YouFor Visiting TheCity Of TamaracA

D

L OK M NQ

D

D

T

G

FH

H G

F

F

L OK M NQ

Type T1-NI / Free Standing Welcome Display

Type T1-NI / Free Standing Welcome Display

X

X

T

Color PaletteSmooth Finish Palette

MAP MP33653“Black Stallion”

D

MAP MP01451“Cold Stone Cream”

B

MAP MP32336“Cliffs of Dover”

A

Textured Finish Palette

MAP MP07380“Golden Lab”

C


I


G


F

HMAP MP07380“Golden Lab”

MAP MP32645“Designer White”

J


E

T

Stone Palette

X

U3M 3630-10

White Translucent Vinyl

V3M 3736-70

White Diffuser

W3M 7725-10White Vinyl

Nominal 1 3/8” thick Stacked “Kurastone”Stone column inset material from Nichiha. Material cut and secured into column baffles with high-bond adhesive mastic and blind fasteners. www.nichiha.com 866-424-4421

3M 680-85Black Reflective

Digital Transparent Vinyl

N

M

K

L

O

PMS 660 -C

PMS 375 -C

PMS 179 -C

PMS 2592 -C

PMS 1495 -C

3M 8914Optically ClearVinyl





P3M 3736-70 Day / Night

Translucent Vinyl

Q

R

S

3M Vinyl Palette

3M 680-10White Reflective

3M 3630-149 “Light Beige”

3M 3630-005 “Ivory”

notes


drawing: T-8


date: 03/31/15


Welcome to



Thank YouFor Visiting TheCity Of Tamarac

XA

X

T

L OK M NP

D

D

T

G

FH

H G

F

F

L OK M NP

Type T1-IL / Free Standing Welcome Display

Type T1-IL / Free Standing Welcome Display


2. 3/4” clear acrylic “push-thru” style shape with clear custom digital UV stable inks in approved PMS color program. 3M 8914 Optically Clear over- laminate over printed surface.

3. Fabricated column feature from 2”x2”x.125” (3A) square aluminum tube with decorative capital. Decorative capital features a 1” x1” aluminum tube bottom collar (3B), .080 aluminum curved filler(3C) with 1.5”x1.5” aluminum tube top cap.(3D) .090 aluminum top cover. (3E) 2”x2” tube construction includes a .080 aluminum inner baffle (3F) to house KuraStone simulated stone material. MPC 113SP textured finish in approved color palette.

6. Front Message display from .090 aluminum sheet (6A) with 90 degree machine formed returns to join panels. Display secured to support posts with bent .090 (6B) aluminum inner shapes, through bolted as required. Front display / back message Panel secured to inner .090 aluminum shapes with #8 flat head fasteners, as required. Upper portion of Ribbon shape finished MPC Gloss Black with lower portion finished in approved color palette selections. Horizontal square tube band and lower portion of panel finished with MPC 287-113SP Course textured additive to satin finished acrylic polyurethane coatings.

7. Horizontal 1.5”x1.5” x.125” aluminum square tube band, capped end with .090 aluminum, blind mounted from behind with #8 flat head SS fasteners. MPC 113SP textured finish in approved color palette.8. FDOT 2015 Approved Design Standards multi-directional break-away post base assembly with 4” OD schedule 40 aluminum round support posts. 9. Below grade embedment of support posts in accordance with FDOT approved practices and specifications with Florida Registered Structural Engineer calculations and documentation/Seal


5. 3/4” thick clear acrylic “push-thru” style graphics (5A) mounted from within a fabricated 3” deep aluminum LED light display. Graphics finished with 3M 3630-20 day/night black vinyl with 3M 3736-70 white diffuser applied second surface. Typical: Front face only. Back face to receive 3M 680-85 (5B)Black reflective message applied directly to face of background panel.



D


B


A



C


I


G


F



J


E

T

Stone Palette

X

U3M 3630-10


V3M 3736-70

White Diffuser





N

M

K

L

O

PMS 660 -C

PMS 375 -C

PMS 179 -C

PMS 2592 -C

PMS 1495 -C







Translucent Vinyl

Q

R

S

3M Vinyl Palette



3M 3630-005 “Ivory”

Welcome toMAINLANDS

PARK

Parks & Recreation DepartmentDNI EJFIEFJKV’ QWO20EJdffweoifjnmfmnfm

SKFWEKFWNE EFVVMEV VMEP;LPK OJWLPFP

Welcome toMAINLANDS

PARK



notes


drawing: T-9


date: 03/31/15





6. Main Message Panels from .090 aluminum sheet (6A) with 90 degree machine formed returns to join panels. Panels secured to support posts with bent .090 (6B) aluminum inner shapes, through bolted as required. Message Panels secured to inner .090 aluminum shapes with #8 flat head fasteners, as required. Entire shape finished MPC Gloss Black per criteria palette selections.

8. FDOT 2015 Approved Design Standards multi-directional break-away post base assembly with 4” OD schedule 40 aluminum round support posts.

9. Below grade embedment of support posts in accordance with FDOT approved practices and specifications with Florida Registered Structural Engineer calculations and documentation/Seal


5. .250” computer routed aluminum plate graphics (5A) blind mounted flush to aluminum background panel. Graphics finished gloss MAP White with 3M 680-10 White reflective message applied to .250” aluminum plate graphics. Typical: Both faces for a double sided display.. For single face versions, Back face to receive 3M 680-10 (5B)White reflective message applied directly to face of background panel.

L OK M NQ

D

D

D

Q

H

HQ

D

E

Type P1-NI / Free Standing Welcome Display

Type P1-NI / Free Standing Welcome Display

X

X

L OK M NQ

Q

Q

E Q

P

P

L OK M NQ

PP

Q

**

*

Note: For displays that are located on non-FDOT traffic medians or ROW’s, a direct burial installation will be allowed which will eliminate the FDOT break-away castings and FDOT below grade approved practices. All other Engineering/ support standards must be met and are applicable.



D


B


A



C


I


G


F



J


E

T

Stone Palette

X

U3M 3630-10


V3M 3736-70

White Diffuser





N

M

K

L

O

PMS 660 -C

PMS 375 -C

PMS 179 -C

PMS 2592 -C

PMS 1495 -C







Translucent Vinyl

Q

R

S

3M Vinyl Palette



3M 3630-005 “Ivory”

Welcome toMAINLANDS

PARK



Welcome toMAINLANDS

PARK



notes


drawing: T-10


date: 03/31/15




D


B


A



C


I


G


F


L OK M NP

D

D

D

Q

H

HQ

D

U


J


E

L OK M NP

Type P1-IL / Free Standing Welcome Display

Type P1-IL / Free Standing Welcome Display

X

X

L OK M NV

Q

V

U V

T

Stone Palette

X

U3M 3630-10


V3M 3736-70

White Diffuser




L OK M NP


N

M

K

L

O

PMS 660 -C

PMS 375 -C

PMS 179 -C

PMS 2592 -C

PMS 1495 -C







Translucent Vinyl




6. Front Message display from .090 aluminum sheet (6A) with 90 degree machine formed returns to join panels. Display secured to support posts with bent .090 (6B) aluminum inner shapes, through bolted as required. Front display / back message Panel secured to inner .090 aluminum shapes with #8 flat head fasteners, as required. Entire display shape finished MPC Gloss Black.




5. 3/4” thick clear acrylic “push-thru” style graphics (5A) mounted from within a fabricated 3” deep aluminum LED light display. Graphics finished with 3M 3630-20 day/night black vinyl with 3M 3736-70 white diffuser applied second surface. Typical for all double sided displays.

7. Remote operated, face mounted EMC. Refer to Pages T-4 and T-5 for manufacturer details and bid specifications.

**

*


Q

R

S

3M Vinyl Palette



3M 3630-005 “Ivory”

Welcome to



Thank YouFor Visiting TheCity Of Tamarac6'-0"

4'-5"

1'-3"

1 1/2"

3 1/2"

6”

2 1/4"

1 1/2"

2 "

1"

4'-5"

1 1/2"

3”

6"

4"

10 "

3'-10"

2 1/2"

notes


drawing: T-11

1

2

6

6

7

5B

1

8

9"

Type T1-NI / Free Standing Welcome Displayscale: 3/4”=1’-0”


date: 03/31/15

scope of work: Type T1 Entrance Specifications

9









5A

4

1B

3E

3D

1C

1A

6B

3A

6A

4

Plan / Frontscale: 3/4”=1’-0”

Plan / Backscale: 3/4”=1’-0”

5"

1'-4"

9”

1’-3”10 "

4

3

Welcome to


Thank YouFor Visiting TheCity Of Tamarac6'-0"

4'-5"

1'-4"

1 1/2"

3 1/2"

6”

2 1/4"

1 1/2"

2 "

1"

4'-5"

1 1/2"

3”

6"

4"

10 "

3'-10"

2 1/2"

1

2

6

6

7

5

1

8

9"

notes


drawing: T-12


date: 03/31/15










9

Type T1-NI / Free Standing Welcome Displayscale: 3/4”=1’-0”

4

1B

3E

3D

1C

1A

6B

3A

6A

4



1'-3"5"

10 "

4

3

notes


drawing: T-13








date: 03/31/15


3E

3D

3C

3B

3A

3F

3E

3D

3C

3B

3A

3F

3E

3D

3C

3B

3A

3F

1A

1B

1C

6A

8

3

4

1A

1B

1C

6A

4

3

6B

7

8

7

6B



Isometric: Type T1-NI / Free Standing Welcome Display

I-1 I-2

I-3I-4

I-5

I-6NOTE: Isometric renderings represent general fabrication process for T-Type, P-Type, MC, CC, RD identity displays for component processes


1"

1 1/2"

3”

6"

4"

notes


drawing: T-14

1

2

6

6

7

5B

1

8

12"

Type T1-IL / Free Standing Welcome Display project: Identity Branding

date: 03/31/15

scope of work: Type T1-ILEntrance Specifications

9


2. 3/4” clear acrylic “push-thru” style shape with clear custom digital UV stable inks in approved PMS color program. 3M 8914 Optically Clear over- laminate over printed surface. Internal LED illumination3. Fabricated column feature from 2”x2”x.125” (3A) square aluminum tube with decorative capital. Decorative capital features a 1” x1” aluminum tube bottom collar (3B), .080 aluminum curved filler(3C) with 1.5”x1.5” aluminum tube top cap.(3D) .090 aluminum top cover. (3E) 2”x2” tube construction includes a .080 aluminum inner baffle (3F) to house KuraStone simulated stone material. MPC 113SP textured finish in approved color palette.


7. Horizontal 1.5”x1.5” x.125” aluminum square tube band, capped end with .090 aluminum, blind mounted from behind with #8 flat head SS fasteners. MPC 113SP textured finish in approved color palette.8. FDOT 2015 Approved Design Standards multi-directional break-away post base assembly with 4” OD schedule 40 aluminum round support posts. 9. Below grade embedment of support posts in accordance with FDOT approved practices and specifications with Florida Registered Structural Engineer calculations and documentation/Seal


5. 3/4” thick clear acrylic “push-thru” style graphics (5A) mounted from within a fabricated 3” deep aluminum LED light display. Graphics finished with 3M 3630-20 day/night black vinyl with 3M 3736-70 white diffuser applied second surface. Internal LED Illumination. Typical: Front face only. Back face to receive 3M 680-85 (5B)Black reflective message applied directly to face of background panel.

5A

4

1B

3E

3D

1C

1A

6B

3A

6A

4



Welcome to



4'-5"

1 1/2"

3 1/2"

6”

2 1/4"

1 1/2"

2 "

10 "

2 1/2"

1

9

scale: 3/4”=1’-0”1'-4"

4'-5"

6'-0"

3'-10"

scale: 3/4”=1’-0”

18"

8"

12”

18”10 "

4

3


1"

1 1/2"

3”

6"

4"

1

2

6

6

7

5B

1

8

9"

Type T1-IL / Free Standing Welcome Display9

5A

4

1B

3E

3D

1C

1A

6B

3A

6A

4

Welcome to


4'-5"

1 1/2"

3 1/2"

6”

2 1/4"

1 1/2"

2 "

10 "

2 1/2"

1

1'-4"

4'-5"

6'-0"

3'-10"

scale: 3/4”=1’-0”

18"

8"

12”

18”10 "

4

3

Plan / Front Plan / Backscale: 3/4”=1’-0”scale: 3/4”=1’-0”

notes


drawing: T-15


date: 03/31/15

scope of work: Type T1-IL Specifications


transformer

electrical disconnect








5. 3/4” thick clear acrylic “push-thru” style graphics (5A) mounted from within a fabricated 3” deep aluminum LED light display. Graphics finished with 3M 3630-20 day/night black vinyl with 3M 3736-70 white diffuser applied second surface. Typical: Front face only. Back face to receive 3M 680-85 (5B)Black reflective message applied directly to face of background panel. Transformer fits within LED display



66

2

5

5

notes


drawing: T-16


date: 03/31/15

scope of work: Type T1-IL Specifications


6

5

5

Isometric: Type T1-IL / Free Standing Welcome Display

I-1 I-2

I-2

I-3








NOTE: Isometric renderings represent general fabrication process for T-Type, P-Type, MC, CC, RD identity displays for component processes

notes

City of TamaracComprehensive Master IdentityCampaignproject: Identity Branding

date: 03/31/15

scope of work: FDOT Specifications

drawing: T-17

8. FDOT 2015Approved Design Standards multi-directional break-away post base assembly with 4” OD schedule 40 aluminum round support posts.


notes

City of TamaracComprehensive Master IdentityCampaignproject: Identity Branding

date: 03/31/15

scope of work: FDOT Specifications

drawing: T-18

8. FDOT 2015Approved Design Standards multi-directional break-away post base assembly with 4” OD schedule 40 aluminum round support posts.


Welcome to

The City For Your LifeTAMARAC5'-6"

1'-0 "

7'-4"

12'-9"

1'-2"

4"6"

5"7"

14'-9"

15'-7"

1'-7"

2"

1 1/2"

notes


drawing: T-19

Type T2-NI / Free Standing Welcome Displayproject: Identity Branding

date: 04/10/15

scope of work: Type T2-NI Entrance Specifications

4

1

2

3

6

7

5


9

8

D

G

F

L OK M NQ

FFD T

X

Plan / Front

scale: 3/4”=1’-0”

scale: 3/4”=1’-0”







4. Nominal 13/8” thick Stacked “Kurastone”Stone column inset material from Nichiha. Material cut and secured into column baffles with high-bond adhesive mastic and blind fasteners. www.nichiha.com 866-424-44215. .250” computer routed aluminum plate graphics (5A) blind mounted flush to aluminum background panel. Graphics finished gloss MAP Black with 3M 680-85 Black reflective message applied to .250” aluminum plate graphics. Typical: Front face only. Back face to receive 3M 680-85 (5B)Black reflective message applied directly to face of background panel.

Welcome to

The City For Your LifeTAMARAC5'-6"

7'-4"

12'-9"

1'-2"

4"6"

14'-9"

15'-7"

1'-7"

2"

notes


drawing: T-20


date: 04/10/15

scope of work: Type T2-IL-E Entrance Specifications

10

5"7"

1 1/2"

4

1

2

3

6

7

5

D

G

F

FFD T

X


2. 3/4” clear acrylic “push-thru” style shape with clear custom digital UV stable inks in approved PMS color program. 3M 8914 Optically Clear over- laminate over printed surface. Internal LED illumination.3. Fabricated column feature from 2”x2”x.125” (3A) square aluminum tube with decorative capital. Decorative capital features a 1” x1” aluminum tube bottom collar (3B), .080 aluminum curved filler(3C) with 1.5”x1.5” aluminum tube top cap.(3D) .090 aluminum top cover. (3E) 2”x2” tube construction includes a .080 aluminum inner baffle (3F) to house KuraStone simulated stone material. MPC 113SP textured finish in approved color palette.




4. Nominal 1 3/8” thick Stacked “Kurastone”Stone column inset material from Nichiha. Material cut and secured into column baffles with high-bond adhesive mastic and blind fasteners. www.nichiha.com 866-424-4421

L OK M NP

10.Remote operated, face mounted 17” x 96” EMC. with 12” x 96” viewing area. Refer to Page T5 T-5 for manufacturer details and bid specifications.


10

separate electrical disconnectfor sign and EMC

1'-0 "

Type T2-IL-EMC / Single Face Free Standing Welcome Display

9

8

scale: 3/4”=1’-0”

transformertransformer


notes


drawing: T-21

Type P1-NI / Double Face Free Standing Park Identity Displayscale: 1/2”=1’-0”


date: 04/10/15

scope of work: Type P1-NI Entrance Specifications

Welcome toMAINLANDS

PARK

Welcome toMAINLANDS

PARK

6'-0"

4'-8"

1'-4 "

1 1/2"

3 1/2"

6”

1 1/2"

2 "

1"

4'-5"

1 1/2"

3”

3'-6"

4

1

3

1

2

6

5

8

5'-1"

10 " 9"





5

7

9


2. 3M 680-10 White reflective cut shapes with clear custom digital UV stable inks in approved PMS color program. 3M 8914 Optically Clear over- laminent over printed surface.

3. Fabricated column feature from 2”x2”x.125” (3A) square aluminum tube with decorative capital. Decorative capital features a 1” x1” aluminum tube bottom collar (3B), .080 aluminum curved filler(3C) with 1.5”x1.5” aluminum tube top cap.(3D) .090 aluminum top cover. (3E) 2”x2” tube construction includes a .080 aluminum inner baffle (3F) to house Kurastone simulated stone material. MPC 113SP textured finish in approved color palette.

6. Main Message Panels from .090 aluminum sheet (6A) with 90 degree machine formed returns to join panels. Panels secured to support posts with bent .090 (6B) aluminum inner shapes, through bolted as required. Message Panels secured to inner .090 aluminum shapes with #8 flat head fasteners, as required. Entire shape finished MPC Gloss Black per criteria palette selections.




5. .250” computer routed aluminum plate graphics (5A) blind mounted flush to aluminum background panel. Graphics finished gloss MAP White with 3M 680-20 White reflective message applied to .250” aluminum plate graphics. Typical: Both Faces for double sided displays.

*

* Note: For displays that are located on non-FDOT traffic medians or ROW’s, a direct burial installation will be allowed which will eliminate the FDOT break-away castings and FDOT below grade approved practices. All other Engineering/ support standards must be met and are applicable.

*

notes


drawing: T-22

Type P1-IL-EMC / Double Face Free Standing Park Identity Displayscale: 1/2”=1’-0”


date: 04/10/15

scope of work: Type P1-IL-E Specifications

Welcome toMAINLANDS

PARK

Welcome toMAINLANDS

PARK

6'-0"

4'-8"

1'-4 "

1 1/2"

3 1/2"

6”

1 1/2"

2 "

1"

4'-5"

1 1/2"

3”

3'-6"

4

1

3

1

2

7

6

5

8

5'-1"

10 " 9"


2. 3/4” clear acrylic “push-thru” style shape with clear custom digital UV stable inks in approved PMS color program. 3M 8914 Optically Clear over- laminate over printed surface. Internal LED illumination.3. Fabricated column feature from 2”x2”x.125” (3A) square aluminum tube with decorative capital. Decorative capital features a 1” x1” aluminum tube bottom collar (3B), .080 aluminum curved filler(3C) with 1.5”x1.5” aluminum tube top cap.(3D) .090 aluminum top cover. (3E) 2”x2” tube construction includes a .080 aluminum inner baffle (3F) to house KuraStone simulated stone material. MPC 113SP textured finish in approved color palette.

6. Message display from .090 aluminum sheet with 90 degree machine formed returns to join panels. Display secured to support posts with bent .090 aluminum inner shapes, through bolted as required. Front display / back message Panel secured to inner .090 aluminum shapes with #8 flat head fasteners, as required. Entire display shape finished MPC Gloss Black.





*

**

7.Remote operated, face mounted 17” x 39” EMC. with 12” x 36” viewing area. Refer to Page T5 for manufacturer details and bid specifications.

4

1B

3E

3D

1C

1A

6B

3A

6A

4



11" 22”

10

10


transformer

11"

22”

5. 3/4” thick clear acrylic “push-thru” style graphics (5A) mounted from within a fabricated 3” deep aluminum LED light display. Graphics finished with 3M 3630-10 White translucent vinyl with 3M 3736-70 white diffuser applied second surface. Internal LED illumination. Typical: Double Face Display.

1'-0 "

Welcome to

It Starts In ParksMAINLANDS PARK

5'-6"

1'-0 "

7'-4"

1'-1"

5"

14'-9"

15'-7"

1'-7"

2"

notes


drawing: T-23Type P2-IL-E / Single Face Free Standing Welcome Displayscale: 1/2”=1’-0”


date: 04/10/15


4

1

2

3

6

5

7 1/2"

75"7"




6. Front Message display from .090 aluminum sheet (6A) with 90 degree machine formed returns to join panels. Display secured to support posts with bent .090 (6B) aluminum inner shapes, through bolted as required. Front display / back message Panel secured to inner .090 aluminum shapes with #8 flat head fasteners, as required. Entire display shape finished MPC Gloss Black.




7. Remote operated, face mounted 17” x 96” EMC. with 12” x 96” viewing area. Refer to Page T5 for manufacturer details and bid specifications.

**

*




2. 3/4” clear acrylic “push-thru” style shape with clear custom digital UV stable inks in approved PMS color program. 3M 8914 Optically Clear over- laminate over printed surface. Internal LED illumination.


9

8

1'-0 "1'-0 "

Type P2-IL-EMC / Double Face Free Standing Welcome Displayscale: 1/2”=1’-0”

9

8

Welcome to

It Starts In ParksMAINLANDS PARK

5'-6"

7'-4"

1'-1"

5"

14'-9"

15'-7"

1'-7"

2"

notes


drawing: T-24


date: 04/10/15


4

1

2

3

6

5

7 1/2"

75"7"



8. FDOT 2015 Approved Design Standards for multi-directional break-away post base assembly with 4” OD schedule 40 aluminum round support posts.




**

*




2. 3/4” clear acrylic “push-thru” style shape with clear custom digital UV stable inks in approved PMS color program. 3M 8914 Optically Clear over- laminate over printed surface. Internal LED illumination.

1'-0" 2'-2"

6. Complete display manufactured as an aluminum skin and frame construction with internal 2” x 2” x 1/4” aluminum L angle sub structure and .125” aluminum faces. Display returns from .090 aluminum over sub-frame. Upper portion of Ribbon shape finished MPC Gloss Black with lower portion finished in approved color palette selections. Horizontal rectangular tube band and lower portion of panel finished with MPC 287-113SP Course textured additive to satin finished acrylic polyurethane coatings.


TAMARACMunicipal ComplexTAMARAC

10'-1"

Municipal Complex

7'-5"

Type MC-IL-EMC / Double Face Free Standing Municipal Complex Identity Displayscale: 1/2”=1’-0”

75257525

TAMARACMunicipal ComplexTAMARACMunicipal Complex

7'-5"

1'-4"

1'-0"

0'-6"

3'-5"

0'-7"

4'-10"

0'-3"

752575251'-6"

0'-5"

0'-5"

1'-8"

6'-0"



2'-2"

1'-4"

3'-0"

8'-10"

notes


drawing: T-25


date: 04/10/15

scope of work: Type MC Specifications

1. Fabricated .090 aluminum ribbon shape, 4” deep, (1A) welded to 4”x4” x.125” aluminum square tube armature, secured within fabricated display.

2. 3/4” clear acrylic “push-thru” style shapes with clear custom digital UV stable inks in approved PMS color program. 3M 8914 Optically Clear over- laminate over printed surface.



7. Horizontal 1”x 3” x.125” aluminum rectangular tube band, mitered, blind mounted from behind with #8 flat head SS fasteners. MPC 113SP textured finish in approved color palette.


5. 3/4” thick clear acrylic “push-thru” style graphics (5A) mounted from within a fabricated 3” deep aluminum LED light display. Graphics finished with 3M 3630-20 day/night black vinyl with 3M 3736-70 white diffuser applied second surface. Internal LED illumination. Typical: Double Face Display.


9. Direct burial of steel supports with Florida certified structural engineering approved foundation and support steel. Provide a 6” tall x 42” x 8’-0” concrete pad as a buffer against landscaping equipment damage.

Planscale: 1/2”=1’-0”

2

1

6

3

5

8

7

3

3

3

9

10'-1"

7'-5"

Type CC-IL-EMC / Double Face Free Standing Community Center Identity Displayscale: 1/2”=1’-0”

75257525

7'-5"

1'-4"

1'-0"

0'-6"

3'-5"

0'-7"

7'-3"

0'-3"

752575251'-6"

0'-5"

0'-5"

1'-8"

6'-0"



2'-2"

1'-4"

3'-0"

8'-10"

notes


drawing: T-26


date: 04/10/15

scope of work: Type CC Specifications

1. Fabricated .090 aluminum ribbon shape, 4” deep, (1A) welded to 4”x4” x.125” aluminum square tube armature, secured within fabricated display.

2. 3/4” clear acrylic “push-thru” style shapes with clear custom digital UV stable inks in approved PMS color program. 3M 8914 Optically Clear over- laminate over printed surface.



7. Horizontal 1”x 3” x.125” aluminum rectangular tube band, mitered, blind mounted from behind with #8 flat head SS fasteners. MPC 113SP textured finish in approved color palette.


5. 3/4” thick clear acrylic “push-thru” style graphics (5A) mounted from within a fabricated 3” deep aluminum LED light display. Graphics finished with 3M 3630-20 day/night black vinyl with 3M 3736-70 white diffuser applied second surface. Internal LED illumination. Typical: Both faces of double face Display


Planscale: 1/2”=1’-0”

2

1

6

3

5

8

7

3

3

3

9

TAMARACCommunity CenterTAMARACCommunity Center

TAMARACCommunity CenterTAMARACCommunity Center


Colony West EstatesColony West Estates5'-6"

7'-4"

12'-9"

14'-9"

15'-7"

1'-7"

2"

1 1/2"

notes


drawing: T-27

Type RD-NI / Free Standing Non Illuminated Single Face Neighborhood Display project: Identity Branding

date: 04/10/15

scope of work: Type RD Specifications

4

1

2

3

6

7

5

A T T A M A R A C







4. Nominal 13/8” thick Stacked “Kurastone”Stone column inset material from Nichiha. Material cut and secured into column baffles with high-bond adhesive mastic and blind fasteners. www.nichiha.com 866-424-44215. .250” computer routed aluminum plate graphics (5A) blind mounted flush to aluminum background panel. Graphics finished gloss MAP Black with 3M 680-85 Black reflective message applied to .250” aluminum plate graphics. Typical: Front face only. Back face to receive 3M 680-85 (5B)Black reflective message applied directly to face of background panel.

7

5

scale: 3/4”=1’-0”


Colony West EstatesColony West Estates5'-6"

7'-4"

12'-9"

14'-9"

15'-7"

1'-7"

2"

1 1/2"

notes


drawing: T-28

Type RD-IL / Free Standing Internally Illuminated Single Face Neighborhood Display project: Identity Branding

date: 04/10/15


4

1

2

3

6

7

5

A T T A M A R A C7

5


2. 3/4” clear acrylic “push-thru” style shape with clear custom digital UV stable inks in approved PMS color program. 3M 8914 Optically Clear over- laminate over printed surface. Internal LED illumination.3. Fabricated column feature from 2”x2”x.125” (3A) square aluminum tube with decorative capital. Decorative capital features a 1” x1” aluminum tube bottom collar (3B), .080 aluminum curved filler(3C) with 1.5”x1.5” aluminum tube top cap.(3D) .090 aluminum top cover. (3E) 2”x2” tube construction includes a .080 aluminum inner baffle (3F) to house KuraStone simulated stone material. MPC 113SP textured finish in approved color palette.4. Nominal 1 3/8” thick Stacked “Kurastone”Stone column inset material from Nichiha. Material cut and secured into column baffles with high-bond adhesive mastic and blind fasteners. www.nichiha.com 866-424-44215. 3/4” thick clear acrylic “push-thru” style graphics (5A)

mounted from within a fabricated 3” deep aluminum LED light display. Graphics finished with 3M 3630-20 day/night black vinyl with 3M 3736-70 white diffuser applied second surface. Internal LED Illumination. Typical: Front face only. Back face to receive 3M 680-85 (5B)Black reflective message applied directly to face of background panel.




scale: 3/4”=1’-0”


Colony West EstatesColony West EstatesA T T A M A R A C

Colony West EstatesColony West EstatesA T T A M A R A C

Plan Viewscale: 3/8”=1’-0”

Note:Both displays share a common

column feature

Type RD-NI or IL / Free Standing Internally Illuminated V-Shape Neighborhood Displayscale: 3/8”=1’-0”

21'-9"

11'-10"

V-Shape Version of the Residential Display can be configured as an RD-NI (Non-Illuminated) or RD-IL (Illuminated) Version.Common fabrication details and specifications apply to both the NI and IL and can be found on pages T-27 and T-28

notes


drawing: T-29


date: 04/10/15



2. 3/4” clear acrylic “push-thru” style shape with clear custom digital UV stable inks in approved PMS color program. 3M 8914 Optically Clear over- laminate over printed surface. Internal LED illumination.3. Fabricated column feature from 2”x2”x.125” (3A) square aluminum tube with decorative capital. Decorative capital features a 1” x1” aluminum tube bottom collar (3B), .080 aluminum curved filler(3C) with 1.5”x1.5” aluminum tube top cap.(3D) .090 aluminum top cover. (3E) 2”x2” tube construction includes a .080 aluminum inner baffle (3F) to house KuraStone simulated stone material. MPC 113SP textured finish in approved color palette.4. Nominal 1 3/8” thick Stacked “Kurastone”Stone column inset material from Nichiha. Material cut and secured into column baffles with high-bond adhesive mastic and blind fasteners. www.nichiha.com 866-424-44215. 3/4” thick clear acrylic “push-thru” style graphics (5A)

mounted from within a fabricated 3” deep aluminum LED light display. Graphics finished with 3M 3630-20 day/night black vinyl with 3M 3736-70 white diffuser applied second surface. Internal LED Illumination. Typical: Front face only. Back face to receive 3M 680-85 (5B)Black reflective message applied directly to face of background panel.




CommunityCenter

MunicipalComplex

AquaticCenter

SportsComplex

RecreationCenter

0'-3" 1'-6"

4'-0

"

1'-7"

CommunityCenter

MunicipalComplex

AquaticCenter

SportsComplex

RecreationCenter

TA

MA

RA

C

0'-4"

24"

5

4

9

2

9

3

1

9’-0” minimumclearance

4

5

6

4'-0

"

1

8

7

2

1'-10"

notes


drawing: T-30

1. One piece .125 aluminum computer routed shape secured into extruded components with a continuous vertical weld.


date: 04/10/15

scope of work: Type DIR Specifications

7. 3M 3930 High Intensity Grade Prismatic White reflective message background applied to computer routed .125” thick aluminum shape on primary message surface. Opposite face to remain blank (no color) 3M 7725-12 Black opaque Directional graphics applied to white reflective background, as message required

2. Charleston Industries Extruded component Part 100Series 2: 2” square extrusion

3. Charleston Industries Extruded component Part 1203 Series 2/3/4 1/8” Panel Adapter

4. 1/4” thick aluminum plate manufactured bracket system

5. 4”x4”x1/4” wall aluminum square tube primary support

6. Breakaway Mounting System: Transpo B525

8. 3M 3930 High Intensity Grade Prismatic White reflective message background with clear custom digital UV stable inks in approved PMS color program. 3M 8914 Optically Clear over- laminent over printed surface.

9. 3/8” diameter Stainless Steel through bolts with nuts /washers, as required

3

Opposite Traffic Patternscale: 1”=1’-0”

Type DIR-1 / City Directional DisplayTypical Directional Placement on a dedicated post

Section Detail

scale: 1”=1’-0”


NMK L O

D

Z Y S

D

D

D


D

S3M 3630-149 “Light Beige”


N

M

K

L

O

PMS 660 -C

PMS 375 -C

PMS 179 -C

PMS 2592 -C

PMS 1495 -C






Y3M 7725-12 Black

Opaque Vinyl

Z3M 3930

High Intensity WhiteVinyl

3M Vinyl Palette Smooth Finish Palette

CommunityCenter

MunicipalComplex

AquaticCenter

SportsComplex

RecreationCenter

0'-2" 1'-6"

4'-0

"

1'-7"

CommunityCenter

MunicipalComplex

AquaticCenter

SportsComplex

RecreationCenter

TA

MA

RA

C

0'-4"

5

4

8

2

9

3

1

9’-0” minimumclearance

4

5

1

7

6

2

1'-10"

notes


drawing: T-31

1. One piece .125 aluminum computer routed shape secured into extruded components with a continuous vertical weld.


date: 04/10/15


6. 3M 3930 High Intensity Grade Prismatic White reflective message background applied to computer routed .125” thick aluminum shape on primary message surface. Opposite face to remain blank (no color) 3M 7725-12 Black opaque Directional graphics applied to white reflective background, as message required

2. Charleston Industries Extruded component Part 100Series 2: 2” square extrusion

3. Charleston Industries Extruded component Part 1203 Series 2/3/4 1/8” Panel Adapter

4. 1/4” thick aluminum plate manufactured bracket system to fit and secure to existing concrete posts as determined and approved by the City/County

5. Existing Concrete Posts.

7. 3M 3930 High Intensity Grade Prismatic White reflective message background with clear custom digital UV stable inks in approved PMS color program. 3M 8914 Optically Clear over- laminent over printed surface.

8. 3/8” diameter Stainless Steel through bolts with nuts /washers, sleeves, as required

3

Opposite Traffic Patternscale: 1”=1’-0”

Type DIR-2 / City Directional DisplayTypical Directional Placement on an existing concrete post

Section Detail

scale: 1”=1’-0”


D

S3M 3630-149 “Light Beige”


N

M

K

L

O

PMS 660 -C

PMS 375 -C

PMS 179 -C

PMS 2592 -C

PMS 1495 -C






Y3M 7725-12 Black

Opaque Vinyl

Z3M 3930

High Intensity WhiteVinyl

3M Vinyl Palette Smooth Finish Palette

8

NMK L O

D

Z Y S

D

D

D

D

D

4'-0

"Note: Bracket sizes will varywith post/location placement

Type DIR-1 City Directional Display

CommunityCenter

MunicipalComplex

AquaticCenter

SportsComplex

RecreationCenter

TA

MA

RA

C

Typical Directional DIR-1Placement on a dedicated post

Welcome to


10'-0 "

CommunityCenter

MunicipalComplex

AquaticCenter

SportsComplex

RecreationCenter

TA

MA

RA

C

Typical Directional Placement on a dedicated post

Welcome to


TA

MA

RA

C

CommunityCenter

MunicipalComplex

AquaticCenter

SportsComplex

RecreationCenter

Typical Directional DIR-2 Placement on an existing post

notes


drawing: T-32


date: 04/10/15


city of tamarac comprehensive master identity campaign

Documents