chhattisgarh state industrial development corporation limited water tanker.pdf · 1/127...

127
1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh Undertaking) 1 st Floor Udhyog Bhawan Ring Road No. -1, Telibhanadha Raipur 492006 (C.G) EPABX No.-91771-6002071-73, Tele Fax : 91771-2583793 & 91771- 4057624 (MKT) CIN- U45203CT1981SG001853 PAN – AABCM6288N Service Tax Regn. No- AABCM6288NSD004. Website: www. csidc.in, Email : [email protected], [email protected] SCHEDULE “C” LIST OF PARALLEL RATE CONTRACT FOR ITEM- Water Tanker S. No. Name of Tenderers Valid Up to Rate Contract No. 1. M/s Agrahari Agrotech Industries, Village-Bori, Tah & Dist.- Rajnandgaon Mob-9753072555 12-04-2017 to 11-04-2018 Rate Contract No. CSIDC/MKD/16-17/ 143/12768/WT/AAI/7915 2. M/s G.V. Industries, 22 A, Industrial Area, Dhar-454001 (M.P.) Mob-9425046639, 9826469388 12-04-2017 to 11-04-2018 Rate Contract No. CSIDC/MKD/ 16-17/ 143/12768/WT/G.V.I/7916 3. M/s National Engineering Works, Opp. Sirpur Lake Indore Ahmedabad Road, Indore (M.P.), Mob-07000233648 1 2 - 04 - 2017 to 11-04-2018 Rate Contract No. CSIDC/MKD/ 16-17/ 143/12768/WT/NEW/7920 4. M/s Netam Engineering Works, Audhogik Area, Bhakhara Road, Villa- Arjuni, Dhamtari, Mob-9406021763, 8602729134 12-04-2017 to 11-04-2018 Rate Contract No. CSIDC/MKD/ 16-17/ 143/12768/WT/NEW/7921 5. M/s New Malwa Agro & Fabricators, Plot No.-59, Sec-C, Sirgitti, Industrial Area, Bilaspur, Mob-9425046639, 7772086742 1 2 - 04 - 2017 to 11-04-2018 Rate Contract No. CSIDC/MKD/ 16-17/ 143/12768/WT/NMA&F/7922 6. M/s Rahul Enterprises, Office- 1016, Roshan Gagh, Pushpa Nagar Road, Esh Bagh (M.P.) Mob.-9826469388, 9826038441 1 2 - 04 - 2017 to 11-04-2018 Rate Contract No. CSIDC/MKD/ 16-17/ 143/12768/WT/RE/7923 7. M/s Shri Sai Steel Industries, Industrial.Area Nainpur, Surajpur, Distt.-Surajpur (C.G.) -497229 Mob.-9826649514 Email- [email protected] 1 7 - 05 - 2017 to 11-04-2018 Rate Contract No. CSIDC/MKD/ 16-17/ 143/12768/WT/SSSI/7919

Upload: others

Post on 19-Aug-2020

7 views

Category:

Documents


1 download

TRANSCRIPT

Page 1: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

1/127

Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh Undertaking) 1st Floor Udhyog Bhawan Ring Road No. -1, Telibhanadha Raipur 492006 (C.G) EPABX No.-91771-6002071-73, Tele Fax : 91771-2583793 & 91771- 4057624 (MKT) CIN- U45203CT1981SG001853 PAN – AABCM6288N Service Tax Regn. No- AABCM6288NSD004. Website: www. csidc.in, Email : [email protected], [email protected]

SCHEDULE “C”

LIST OF PARALLEL RATE CONTRACT FOR ITEM- Water Tanker

S.

No. Name of Tenderers Valid Up to Rate Contract No.

1. M/s Agrahari Agrotech Industries, Village-Bori, Tah & Dist.- Rajnandgaon Mob-9753072555

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/16-17/ 143/12768/WT/AAI/7915

2. M/s G.V. Industries, 22 A, Industrial Area, Dhar-454001 (M.P.) Mob-9425046639, 9826469388

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/ 143/12768/WT/G.V.I/7916

3. M/s National Engineering Works, Opp. Sirpur Lake Indore Ahmedabad Road, Indore (M.P.), Mob-07000233648

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/ 143/12768/WT/NEW/7920

4. M/s Netam Engineering Works, Audhogik Area, Bhakhara Road, Villa-Arjuni, Dhamtari, Mob-9406021763, 8602729134

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/ 143/12768/WT/NEW/7921

5. M/s New Malwa Agro & Fabricators, Plot No.-59, Sec-C, Sirgitti, Industrial Area, Bilaspur, Mob-9425046639, 7772086742

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/ 143/12768/WT/NMA&F/7922

6. M/s Rahul Enterprises, Office- 1016, Roshan Gagh, Pushpa Nagar Road, Esh Bagh (M.P.) Mob.-9826469388, 9826038441

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/ 143/12768/WT/RE/7923

7. M/s Shri Sai Steel Industries, Industrial.Area Nainpur, Surajpur, Distt.-Surajpur (C.G.) -497229 Mob.-9826649514 Email- [email protected]

17-05-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/ 143/12768/WT/SSSI/7919

Page 2: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

2/127

Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh Undertaking) 1st Floor Udhyog Bhawan Ring Road No. -1, Telibhanadha Raipur 492006 (C.G) EPABX No.-91771-6002071-73, Tele Fax : 91771-2583793 & 91771- 4057624 (MKT) CIN- U45203CT1981SG001853 PAN – AABCM6288N Service Tax Regn. No- AABCM6288NSD004. Website: www. csidc.in, Email : [email protected], [email protected]

No./CSIDC/MKD/PS-III/16-17/ Raipur, Dated : Registered A/D Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/AAI/7915 Dt.: 12-04-2017

To, M/s Agrahari Agrotech Industries, Village-Bori, Tah & Dist.- Rajnandgaon (C.G.) Mob-9753072555 [email protected] Sub :- Rate Contract for the supply of Water Tanker (Valid From dated 12-04-2017 to 11-04-2018)

Ref :- (I) This Office Tender Enquiry No. CSIDC/MKD/16-17/143/12768

(II) Your Offer acceptance along with undertaking submitted on dated 06-04-2017

Dear Sir,

You are hereby informed that your above referred tender read with subsequent letters mentioned above for the Stores specified in the Schedules annexed has been accepted. This Rate Contract will be governed by the terms and conditions brought in CSIDC Form No.1 & 2. The Rate Contract and the Schedules annexed hereto shall be the sole repository of this Rate Contract / Transaction. You are required to show the original INK-SIGNED subject Rate Contract to the satisfaction of Direct Demanding Officer who will place the supply order as per instructions contained in CSIDC form No. 2 and also to the Quality Assurance Officer for inspection purpose and to the Paying Authority at the time of getting the payment .

Conditions to be fulfilled by the Purchaser Department (DDO’s) for purchase of store from the Rate Contract holders and Quality Assurance Officer for Inspection of store before delivery :-

It is sole responsibility of the Purchase Department’s (DDO’s) and Quality Assurance Officer to comply with the following conditions as a pre-requisite before accepting delivery/conducting Inspections – (1) Purchase Department’s (DDO’s) shall ensure the validity of following documents applicable for the

Rate Contract Holder to his satisfactions :- A. Udyog Aadhar Memorandum, Valid Operational Certificate. B. PAN Card No., Sales Tax/VAT Tax Registration (TIN).

(2) The above set of documents (As applicable) are required to be inspected by the Quality Assurance Officer before conduction inspection of store.

(3) In case, on the date of delivery OR Inspection, if any of document as mentioned above are not valid OR the validity period of which has been expired. no inspection would be conducted and also no delivery of store to be received from the Rate Contract Holder.

Incharge Marketing

Page 3: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

3/127 (4) Purchase Department’s (DDO’s)/Quality Assurance Officer would be responsible for the any

consequence which may arise due to non compliance of the above conditions and shall keep CSIDC indemnified of any such consequence.

SCHEDULES ANNEXED: 1. Schedule “A” Description of Stores, Prices, Duties / Taxes. 2. Annexure -“B” Technical Particulars of Item Water Tanker. 3. Schedule “B” Special conditions of contract (if any). 4. Schedule “C” Information to DDOs about parallel rate contracts. 5. Schedule “D” Format for Drawal Report.

Total- 18 Pages. Yours faithfully,

(Subas Chandra Bhagat) Incharge Marketing

For and on behalf of the purchaser named in CSIDC Form No.2

Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/AAI/7915 Dt.: 12-04-2017 +

Copy to :-

1. The Secretary, Chhattisgarh Vidhan Sabha, Raipur.

2. The Registrar, Honourable High court Chhattisgarh, Bilaspur.

3. The Accountant General Chhattisgarh State, Raipur.

4. All HODs of Chhattisgarh Govt.

5. All The Collectors, Chhattisgarh Govt.

6. The Director Treasury, Chhattisgarh Govt. with a request to circulate the copy of Rate Contract to all Direct Demanding Officers of your

institution against issue of purchase order (Indent) in favor of Rate Contract Holders of CSIDC,

7. (i) The Director Education Department (DPI) Indrawati Bhawan, Naya Raipur (C.G.) (ii) The Commissioner Tribal Welfare Department Indrawati Bhawan, Naya Raipur (C.G.) (iii) The Commissioner Directorate of Women & Child Development Indrawati Bhawan, Naya Raipur (C.G.) (iv) Principle Chief Conservator of Forest C.G. Raipur.

8. (i) CSIDC (DEPARTMENTAL TECHNICAL WING) (ii) ADG (Q & A) , DGS&D, Jeewan Tara Building 5 Parliament Street New Delhi 110001 (iii) Manager (Operation) Indian Register of Shipping, Senior MIG-2, Secter A, 1st Floor, Infront

of Bank of India Indrapuri Bhopal. (iv) Chief Engineer, PDIL, 4th floor, 4/2 Karaya Road, 67 Shekespeare Sarani, Kolkata (W.B.) (v) General Manager (Inspection) RITES Ltd., Churchgate Station Road, Second Floor, M.K.

Road, Mumbai-400020 (vi) Operations Manager SGS India Pvt, Ltd. 43, RR Arcade, Zone-2, MP Nagar, Bhopal (MP)-

462011.

9. Manager (Tender), Marketing Div., CSIDC Ltd., Raipur. He is requested to maintain a master file of Rate Contract.

10. Computer cell, CSIDC Ltd., Raipur to release Rate Contract on CSIDC website.

11. Main file of Item- “Water Tanker.”

Incharge Marketing

For and on behalf of the purchaser named in CSIDC Form No.2

Page 4: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

4/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/AAI/7915 Dt.: 12-04-2017

SCHEDULE “A” Description of Stores, Prices, Duties/Taxes

For the supply of Item- Water Tanker as per Annexure’A’ enclosed.

1. (a) NAME AND FULL ADDRESS OF :- M/s Agrahari Agrotech Industries, THE FIRM Village-Bori,

Tah & Dist.- Rajnandgaon (C.G.) Mob-9753072555 [email protected]

(b) NAME AND FULL ADDRESS OF :- M/s Agrahari Agrotech Industries, MANUFACTURER Village-Bori,

Tah & Dist.- Rajnandgaon (C.G.)

(c) Catagery :- GEN

2. VALIDITY OF RATE CONTRACT :- From 12-04-2017 to 11-04-2018

3. DESCRIPTION OF ITEM- Water Tanker.

Item Code No.

Item Description Class Rate ( ) F.O.R. Destination

ED NA & VAT Extra if Applicable

Rate Per Unit 1 2 3

WT001 (A) Tankers Mounted On Four Wheel Trolley (With 7.50 X 16 Tyre & Tube) With Leaf Spring 5000 Liters

127139.00

WT002 4500 liters 123143.00 WT004 (A) Tankers Mounted On Four Wheel Trolley (With 7.50 X 16 Tyre &

Tube) Without Leaf Spring 5000 Liters 119060.00

WT005 4500 liters 115871.00 WT006 3500 liters 102104.00 WT007 (B) Tankers Mounted On Two Wheel Trolley With Leaf Spring 3500 Liters 90889.00 WT008 2500 Liters 80259.00 WT009 (B) Tankers Mounted On Two Wheel Trolley Without Leaf Spring 3500

Liters 88763.00

WT010 2500 Liters 73677.00 WT011 (C) Tankers Mounted On Four Wheel Trolley: (With 9x20 Tyres Tubes)

4000 Liters 122249.00

WT012 5000 Liters 127669.00 WT013 (D) Tankers Mounted On Two Wheel Trolley With Leaf Spring 4000 Liters 104178.00 WT014 4500 liters 110413.00 WT015 5000 Liters 117785.00 WT016 5500 Liters 123109.00 WT017 (D) Tankers Mounted On Two Wheel Trolley Without Leaf Spring: 4000

Liters 100457.00

WT018 4500 liters 106303.00 WT019 5000 Liters 114755.00 WT020 5500 Liters 120123.00

Note :- Technical particulars as per Annexure B enclosed

(Subas Chandra Bhagat)

Incharge Marketing

Page 5: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

5/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/AAI/7915 Dt.: 12-04-2017 4. TERMS OF DELIVERY : F. O. R Destination (Any where in C.G. State)

5. EXCISE DUTY : Not Applicable

6. SALES TAX /VAT : Extra, if applicable

TIN No. 22243609608 Address:-

M/s Agrahari Agrotech Industries, Village-Bori, Tah & Dist.- Rajnandgaon (C.G.)

7. DELIVERY PERIOD : 45 Days

8. a. ANNUAL TURN OVER/ : NM

b. MONETARY LIMIT : NM

c. INSTALLED CAPACITY : (As per UAM Certificate)

Water Tanker

Description Annual Capacity

Water Tanker 50 Nos.

9. SLAB DISCOUNT (IF ANY) : Nil 10. PRICES : Prices are Firm and Final 11. MINIMUM QUANTITY IN : Not Mentioned. SINGLE SUPPLY ORDER 12. STATUS OF RC HOLDING : Manufacturer

FIRM 13. REGISTRATION STATUS : Manufacturer is Registered with MSME-UAM UAN- CG15A0000541, Dt. 24-12-2016 14 BIS LICENSE : Not Applicable 15. PAYING AUTHORITY : As Mentioned in supply order to be issued by Direct Demanding Officers (DDOs).

16. PAYMENT TERMS : The payment of full 100% of prices of the stores of each consignment there-of will be made after receipt and acceptance of the stores by the consignee/interim consignee in full and good condition within 20 days as per SPR rule No.11, if the bills are in order. In case of delay in payment without any reason the department will be liable to pay interest as per prevailing bank rate. Bills are to be submitted in the prescribed form of the paying authority of purchaser / indenter and are to be supported with inspection note issued by the inspector and consignee’s Receipt Certificate.

(Subas Chandra Bhagat)

Incharge Marketing

Page 6: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

6/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/AAI/7915 Dt.: 12-04-2017

17 INSPECTION AUTHORITY : CSIDC (DEPARTMENTAL TECHNICAL WING) Bhilai OR ADG (Q & A) , DGS&D, Jeewan Tara Building 5 Parliament Street New Delhi 110001 OR Manager (Operation) Indian Register of Shipping Senior MIG-2, Secter A, 1st Floor, in front of Bank of India Indrapuri Bhopal (M.P.)

OR Chief Engineer, Project & Development India Ltd. 4st floor, 4/2 Karaya Road, 67 Shekespeare Sarani Kolkata (W.B.)

OR General Manager (Inspection) RITES Ltd. Churchgate Station Road, Second Floor, M.K. Road, Mumbai- 400020 (Mah) OR

Manager (Operations) SGS India Pvt. Ltd. 43, RR Arcade, Zone-2, MP Nagar, Bhopal-462011. (M.P.)

18 QUALITY ASSURANCE: CSIDC (DEPARTMENTAL TECHNICAL WING) Bhilai

Shri Sanjiv Awasthy Mob. No. 9926999936 Email- [email protected] OR Dy. Director (Q&A), DGS&D, Bhilai (C.G.) DGS&D, Sector 1, Street-10 Old Telegraph Office, Bhilai (C.G), Fax No.- 0788-2223374 OR Manager (Operation) Indian Register of Shipping Senior MIG-2, Secter A, 1st Floor, in front of Bank of India Indrapuri Bhopal. (M.P.) Shri Amit Kumar Gupta Mob. No. 8871453225] M. Nazim Athar Mob. No. 8085182339

E-mail- [email protected] OR

Chief Engineer, Project & Development India Ltd. 4st floor, 4/2 Karaya Road, 67 Shekespeare Sarani Kolkata (W.B.) Fax No. 033-22873274 OR

General Manager (Inspection) RITES Ltd. Rajnish Ahuja Western Region (Inspection) Pho. No 2201- 2523/5573 Direct 2201 7434 Mob. 08600 017717 Fax 022 22084155, 2222016219

E-mail- [email protected], [email protected] OR

Manager (Operations) SGS India Pvt. Ltd. 43, RR Arcade, Zone-2, MP Nagar, Bhopal-462011. (M.P.) Shri Jitendra Raj Mob. No. 9752848321

E-mail- [email protected]

(Subas Chandra Bhagat)

Incharge Marketing

Page 7: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

7/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/AAI/7915 Dt.: 12-04-2017 19. PLACE WHERE THE STORES At Manufacturer’s Factory at

ARE TO BE OFFERED FOR M/s Agrahari Agrotech Industries, INSPECTION Village-Bori,

Tah & Dist.- Rajnandgaon (C.G.)

20 INSPECTION CHARGES : Inspection charges 0.60%+ Service Tax As applicable to be paid extra at the time of inspection to Quality Assurance Officer which will be billed by the unit along with bill of the material and will be reimbursed by the paying authority of DDO.

21. SECURITY DEPOSIT : As per General conditions of contract, CSIDC Form No. 1, Clause 7,the Purchaser/DDOs may require the contractor to furnish a security deposit which shall be made after issue of the acceptance of the supply order within the period specified by the purchaser / DDOs. Such security deposit shall not ordinarily exceed 3% . The security shall be in form of Demand Drafts issued by any of the Scheduled Commercial Banks. No other form of security is to be accepted. The security deposit amount is to be refunded after successful completion of the supply.

22. Special Note 1. Purchasing Departments/end user will ensure to sending the copy of every Purchase order to this office. 2. Purchasing Departments/end user will ensure to Pre Dispatch inspection of stores through Inspection agency enlisted in the CSIDC Panel. 3. Purchasing Departments/end user will be responsible for ensuring the Quality of accepted stores. As per the Tech. Specification. 4. Purchasing Department/end user shall be ensure to execute the Integrity Pact between BUYER and BIDDER/ SUPPLIER in accordance with the letter vide No.799/eq-l- @2013 New Raipur Dated 10.07.2013 and 243/fo-@fu- @pkj@2013 New Raipur Dated 06.07.2013 issued by the Chief Secretary. Govt. of Chhattisgarh. 5. Purchasing Department/end user will ensure to issue the

Purchase Order in accordance with the Store Purchase Rules-2002 (As Amended) vide Clause No.-13

(Subas Chandra Bhagat) Incharge Marketing

Page 8: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

8/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/AAI/7915 Dt.: 12-04-2017

Annexure-B CSIDC/MKD/TECH/2016-17/28

SPECIFICATION FOR WATER TANKER MOUNTED ON FOUR / TWO WHEEL TROLLEY

TSC 23-11-2016

(E) SPECIFICATION OF PRODUCTS

(A) TANKERS MOUNTED ON FOUR WHEEL TROLLEY (WITH 7.50 X 16 TYRE & TUBE) WITH LEAF SPRING OR WITHOUT LEAF SPRING

1. Chassis:

The Chassis shall be fabricated as per standard practice to mount the MS tank. All the joint shall be welded with gusset plates wherever required as per standard practice.

The Chassis frame shall have two longitudinal member and 5 cross members of channel

section of size 125 x 65 mm (ISMC) for 4500 & 5000 lts. Capacity. For 3500 lts. Capacity the chassis frame shall have two longitudinal members and 4 cross members of channel section of size 100 x 50 mm (ISMC) The overall approximate dimensions of various tanker trolley chassis shall be as under:- -----------------------------------------------------------------------------------------------------

S.No. Approx.Cap Length Width -----------------------------------------------------------------------------------------------------

1. 5000 liters 4 metres 1.00 mtr. 2. 4500 liters 4 meters 1.00 mtr. 3. 3500 liters 3.5 meters 1.00 mtr.

-----------------------------------------------------------------------------------------------------

2. Turn table:

The turn table frame shall be made out of 100x50mm (ISMC) MS channel with cross support, fixed with double rings fabricated from Angle Iron 40x40x6 mm and with 40mm diameter centre pin with suitable washer and locking arrangement.

3. Draw Bar:

Draw bar shall be in triangular construction made out of ISMC of size 100x50 mm with spring loaded eyehook made of 40mm dia MS bar.

The straight length of draw bar should be 150 cms including eye hook. Draw bar shall be hinged with the frame of turn table by 500 x 25mm Ms round bar having locking arrangement at both the end.

4. Axle & Brake assembly:

Axle shall be made from 63 x 63mm square bar with both the end machined, threaded and fitted with hubs and hexagonal lock nut, fitted with twin taper roller bearings, and provided with grease nipples for greasing the moving parts. For braking mechanical-internal expanding type brakes with suitable drums. hand operated, on rear wheels compete, with steel rod, clamps, springs and hand lever be provided.

(S.N. Chopra)

Incharge PS-III

Page 9: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

9/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/AAI/7915 Dt.: 12-04-2017

5. Leaf Spring:

Four sets of leaf spring consisting of 13 leaves of size minimum 70 x 10mm, 1000mm long (distance between two pin) of alloy steel shall be provided. These leaf spring shall be fixed with frame by means of complete cast iron bracket assembly.

6. Tyres, tubes & wheel Assembly :

Four number tyre of 7.50 x 16 and tubes of standard make, Shall be provided with double plated rims 5mm thick with 5/6 nos. holes.

7. Water tanker:

The Water Tanker shall have capacity of 5000, 4500 & 3500 litres approx., and shall be manufactured in elliptical shape/ semi elliptical shape. The approx size of Water Tanker shall be as follows:- ----------------------------------------------------------------------------------------------------------- S. No. Approx. Major Axis Minor Axis Length ----------------------------------------------------------------------------------------------------------- 1. 5000 lit. 1.95 mtrs. 1.05 mtrs. 3.6 mtrs. 2. 4500 lit. 1.75 mtrs. 1.05 mtrs. 3.6 mtrs. 3. 3500 lit.. 1.5 mtrs 1.05 mtrs. 3.0 mtrs -----------------------------------------------------------------------------------------------------------

The tank shall be made out of 3.15mm thick MS sheet, and end plates of 4.0mm thick MS plate. End plate shall be maximum in two piece.

The tank shall be reinforced from inside by welding four numbers of elliptical rings made of 40 x 40 x 6mm MS angle one at both ends and two in between at suitable distance (total 04 on.) for 4500 & 5000 lts capacity. For 3500 lts capacity angle rings shall be provided at both ends and one at the middle (total 03 no.)

Two nos. baffle plate of 3.15mm thick MS sheet shall be provided in side the tank. These plates shall be properly welded with the central ring as per the standard practice. The height of baffle plate shall be 20cm. More than half of the height of tank. For 3500 lts capacity only one baffle plate be provided.

8. Manhole:

Two manhole with hinged cover shall be provided at the top of the tank. The cover of tank shall be fabricated from 3.15 thick MS sheet. The collar of the cover and manhole shall be made out of 4.00 mm MS strip. Locking arrangement for cover shall be provided; The manhole covers shall be such fabricated so that no foreign material may enter into the tank.

A 300 mm wide five steps ladder made of 32 x 32 x 2.5/3mm Ms angle be provided at left hand on rear side of the tanker (i.e. cleaner seat side). One no. 300 mm wide platform for full length at left hand be provided at appropriate level. The platform frame be made from Angle Iron 32 x 32 x2.5/3mm and 2.5 mm thick MS sheet. A suitable railing of 150 mm height on full length of platform shall be provided at the outer side of the platform by using 25x25x2.5/3mm Angle Iron or 25mm pipe and 2.0 mm MS sheet.

(S.N. Chopra) Incharge PS-III

Page 10: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

10/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/AAI/7915 Dt.: 12-04-2017

The rear wheels shall be covered with mudguards fabricated out of 1.6mm thick MS sheets,

as per standard practice.

The Water Tanker shall be fixed on the chassis by 8 nos. suitable arranged fabricated shoes (box type brackets) from 5mm thick plates and base plate of approximate size 23x17 cms. and 12mm thick OR made of suitable ISMC bolted to the chassis with suitable ‘U’ clamps (two nos. in each base) The box brackets width shall not be less than 60mm and the bottom of the tank shall be provided with 6 mm thick and 120mm wide saddle plates for full width of the tank as a base for the shoes (box type brackets).

9. Ball Bering No. 31213 must be used. (B) TANKERS MOUNTED ON TWO WHEEL TROLLEY WITH LEAF SPRING OR

WITHOUT LEAF SPRING 1. Chassis:

The Chassis shall be fabricated as per standard practice to mount the MS tank. All the joint shall be welded with gusset plates wherever required as per standard practice.

The Chassis frame shall have two longitudinal member and 4 cross members of channel

section of size 100 x 50 mm (ISMC).

The overall approximate dimensions of various tanker trolley chassis shall be as under:- -----------------------------------------------------------------------------------------------------

S.No. Approx.Cap Length Width -----------------------------------------------------------------------------------------------------

1. 3500 liters 3.0 metres 0.80 mtr. 2. 2500 liters 2.5 meters 0.80 mtr.

----------------------------------------------------------------------------------------------------- 2. Draw bar:

Draw bar shall be in triangular construction made out of MS channel of size 100 x 50 mm with spring loaded eyehook made of 40 mm dia MS bar.

The straight length of draw bar should be 150 cms including eye hook.

3. Axle & Brake assembly:

Axle shall be made from 63 x 63mm square bar with both the end machined and threaded and provided with iron hubs and hexagonal lock nut, fitted with twin taper roller bearings and provided with grease nipples for greasing the moving parts.

4. Leaf spring:

Two sets of leaf spring consisting of 13 leaves of size 70 x 10mm minimum 1000 mm long (distance between two pin) of alloy steel shall be provided. These leaf spring shall be fixed with frame by means of complete cast iron bracket assembly.

5. Tyres, tubes & wheel Assembly:

(S.N. Chopra)

Incharge PS-III

Page 11: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

11/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/AAI/7915 Dt.: 12-04-2017

Two number tyres of 7.50 x 16 and tubes of standard make shall be provided with double plated rims 5 mm thick with 5/6 nos. holes for 2500 lts. Capacity tanker. For 3500 lts. Capacity two number tyres of 9x16 and tubes of standard make shall be provided.

6. Water Tanker:

The Water Tanker Should have capacity of 2500 & 3500 liters approx. Manufactured in elliptical. Shape. The approx. size of Water Tanker are as follows :-

-------------------------------------------------------------------------------------------------------------- S.No. Approx.Cap Major Axis Minor Axis Length -------------------------------------------------------------------------------------------------------------- 1. 3500 liters 1.5 mtrs 1.05 mtrs 3.0 mtrs. 2. 2500 liters 1.20 mtrs 1.05 mtrs 2.5 mtrs. --------------------------------------------------------------------------------------------------------------

The tank shall be made out of 3.15 mm thick MS sheet, and end plates of 4.0 thick MS plate. End plate should be maximum two pieces.

The tank shall be reinforced from inside by welding three numbers of elliptical rings made of 40 x 40 x 6mm MS angle one at both ends and one in between at suitable distance.

One baffle plate of 3.15mm shall be provided inside the tank. These plates shall be properly welded with the central ring as per the standard practice. The height of baffle plate shall be 20 cm more than half of the height of tank.

7. Manhole:

One manhole with hinged cover shall be provided at the top of the tank. The cover of tank shall be fabricated from 3.15 thick MS sheet. The collar of the cover and manhole shall be made out of 4.00 mm MS strip. Locking arrangement for cover shall also be provided; The manhole cover shall be such fabricated so that no foreign material may enter in to the tank.

A 300 mm wide three steps ladder made of 32x32x2.5/3mm MS angle be provided at left hand on front side of the tanker (i.e. cleaner seat side). One no. 300mm wide platform for full length at left hand be provided at appropriate level. The platform frame be made from angle iron 32x32x2.5/3mm and 2.5 mm thick MS sheet. A suitable railing of 150mm height on full length of platform shall be provided at the outer side of the platform by using 25x25x3mm Angle Iron of 25mm pipe and 2.0mm MS Sheet.

The water tanker shall be fixed on the chassis by 6 nos. suitable arranged fabricated shoes (box type brackets) from 5mm thick plates and base plate of approximate size 23 x 17 cms. and 12 mm thick OR made of suitable ISMC bolted to the chassis with suitable ‘U’ clamps (two nos. in each base). The box brackets width shall not be less than 60 mm and the bottom of the tank shall be provided with 6 mm thick and 120 mm wide saddle plates for full width of the tank as a base for the shoes (box type brackets.)

8. Ball Bering No. 31213 must be used.

(C) TANKERS MOUNTED ON FOUR WHEEL TROLLEY: (WITH 9X20 TYRES TUBES)

1. Chassis: The Chassis shall be fabricated as per standard practice to mount the MS tank. All the joint

shall be welded with gusset plates wherever required as per standard practice.

(S.N. Chopra)

Incharge PS-III

Page 12: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

12/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/AAI/7915 Dt.: 12-04-2017

The chassis frame shall have two longitudinal member and 3 cross members of channel section of size 150x75mm (ISMC) for 4000 & 5000 It. Capacity.

The width of the chassis frame shall be of 1.0mt and length shall be equal to the length of the tank.

2. Turn table:

The turn table frame shall be made out of 100x50mm (ISMC or equivalent) MS channel with cross support, fixed with double rings fabricated out of Angle Iron 40x40x6 mm and with 40mm diameter centre pin with suitable washer and locking arrangement.

3. Draw Bar:

Draw bar shall be in triangular construction made out of Ms Channel of size 100x50 mm with spring loaded eyehook made of 40mm dia MS bar.

The straight length of draw bar should be 150 cms including eye hook. Draw bar shall be hinged with the frame of turn table by 100x25mm MS round bar having locking arrangement at both the end.

4. Axle & Brake assembly:

Axle shall be made from 63x63mm square bar of 1750mm length with both the end machined and threaded and provided with iron hubs and hexagonal lock nut, fitted with twin taper roller bearings, and provided with grease nipples for greasing the moving parts. For braking mechanical-internal expanding type brakes with suitable drums, hand operated, on rear wheels compete, with steel rod, clamps, springs and hand lever be provided.

5. Leaf Spring:

Four sets of leaf spring consisting of 13 leaves of size 70x11 mm minimum 1000mm long (distance between two pin) of alloy steel shall be provided. These leaf spring shall be fixed with frame by means of complete cast iron bracket assembly.

6. Tyres, tubes & wheel Assembly :

Four number tyre of 9 x 20 and tubes of standard make. Shall be provided with double plated rims 5 mm thick with 5/6 nos. holes. For four wheel trolley.

7. Water tanker:

The Water Tanker shall have capacity of 5000 & 4000 litres approx. manufactured in semi elliptical shape.

The minor axis of the tank shall be of 1.05 mtr. The manufacturer shall design major axis

and length of the semi elliptical tank accordingly. The tank shall be made out of 3.15 mm thick MS sheet, and end plates of 4.0 thick MS plate.

End plate should be maximum two pieces.

(S.N. Chopra)

Incharge PS-III

Page 13: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

13/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/AAI/7915 Dt.: 12-04-2017

The tank shall be reinforced from inside by welding three numbers of elliptical rings made of 40 x 40 x 6mm MS angle one at both ends and one in between at suitable distance.

Two baffle plate of 3.15mm shall be provided in side the tank. These plates shall be properly

welded with the central ring as per the standard practice. The height of baffle plate shall be 20 cm more than half of the height of tank.

8. Manhole:

Two manhole with hinged cover shall be provided at the top of the tank. The cover of tank shall be fabricated from 3.15 thick MS sheet. The collar of the cover and manhole shall be made out of 4.00 mm MS strip. Locking arrangement for cover shall also be provided; The manhole cover shall be such fabricated so that no foreign material may enter in to the tank.

A 300 mm wide three steps ladder made of 30x30x3mm MS angle be provided at left hand

on front side of the tanker. One no. 300mm wide platform for full length at left hand be provided at appropriate level. The platform frame be made from angle iron 35x35x3mm and 2.5 mm thick MS sheet. A suitable railing of 150mm height on full length of platform shall be provided at the outer side of the platform by using 25x25x3mm Angle Iron of 25mm pipe and 2.0mm MS Sheet.

The water tanker shall be fixed on the chassis by 8 nos. suitable arranged fabricated shoes

(box type brackets) from 5mm thick plates and base plate of approximate size 23 x 17 cms. and 12mm thick bolted to the chassis or made of 100x50mm channel properly covered with sheet of 3.15mm suitable ‘U’ clamps (two nos. in each base). The box brackets width shall not be less than 60 mm and the bottom of the tank shall be provided with 6 mm thick and 120 mm wide saddle plates for full width of the tank as a base for the shoes (box type brackets.)

9. Ball Bering No. –31213 must be used. (D) TANKERS MOUNTED ON TWO WHEEL TROLLEY WITH LEAF SPRING OF

WITHOUT LEAF SPRING: 1. Chassis:

The Chassis shall be fabricated as per standard practice to mount the MS tank. All the joint shall be welded with gusset plates wherever required as per standard practice.

The Chassis frame shall have two longitudinal members and 4 cross members of channel

section of size 150 x 75 mm (ISMC) The overall approximate dimensions of various tanker trolley chassis shall be as under:- -----------------------------------------------------------------------------------------------------

S.No. Approx.Cap Length Width -----------------------------------------------------------------------------------------------------

1. 4000 liters 3.3 metres 1.2 mtr. 2. 4500 liters 3.5 meters 1.2 mtr. 3. 5000 liters 3.5 meters 1.2 mtr. 4. 5500 liters 3.7 metres 1.2 mtr.

-----------------------------------------------------------------------------------------------------

(S.N. Chopra) Incharge PS-III

Page 14: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

14/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/AAI/7915 Dt.: 12-04-2017 WATER TANKERS MOUNTED ON FOUR/TWO WHEEL TROLLEY 2. Draw Bar:

Draw bar shall be in triangular construction made out of MS channel of size 150x75 mm with spring loaded eyehook made of 40mm dia MS bar.

The minimum straight length of draw bar should be 150 cms including eye hook.

3. Axle & Brake assembly:

Axle shall be made from 72 x 72mm square bar with both the end machined and threaded and provided with iron hubs and hexagonal lock nut, fitted with twin taper roller bearings and provided with grease nipples for greasing the moving parts.

4. Leaf Spring:

Two sets of leaf spring consisting of 13 leaves of 4000 & 4500 Ltr. And 19 leaves for 5000 & 5500 ltr. Cap. Of size minimum 70 x 10mm minimum 900mm long (distance between two pin) of alloy steel shall be provided. These leaf spring shall be fixed with frame by means of complete cast iron bracket assembly.

5. Tyres, tubes & wheel Assembly :

Two number tyre of 9 x16 / 9x16 and tubes of standard make Shall be provided with double plated rims 5mm thick with 8 nos. holes.

6. Water tanker:

The Water Tanker should have capacity of 5000, 5500 litres approx. manufactured in elliptical shape. The approx size of Water Tanker are as follows:- ----------------------------------------------------------------------------------------------------------- S. No. Approx. Major Axis Minor Axis Length ----------------------------------------------------------------------------------------------------------- 1. 4000 lit. 1.65 meters 1.11 mtrs. 2.8 mtrs. 2. 4500 lit. 1.70 meters 1.13 mtrs. 3.0 mtrs. 3. 5000 lit. 1.80 meters 1.18 mtrs. 3.0 mtrs 4. 5500 lit. 1.80 meters 1.22 mtrs. 3.2 mtrs. -----------------------------------------------------------------------------------------------------------

WATER TANKERS MOUNTED ON FOUR/TWO WHEEL TROLLEY

The tank shall be made out of 3.15mm thick MS sheet, and end plates of 4.0mm thick MS plate. End plate should be in maximum two pieces.

The tank shall be reinforced form inside by welding three numbers of elliptical rings made of

40x40x6mm MS Angle one at both ends and one in between at suitable distance.

One baffle plate of 3.15mm shall be provided in side the tank. These plates shall be properly welded with the central ring as per the standard practice. The height of baffle plate shall be 20cm. more than half of the minor axis of tank.

(S.N. Chopra)

Incharge PS-III

Page 15: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

15/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/AAI/7915 Dt.: 12-04-2017 7. Manhole:

One manhole with hinged cover shall be provided at the top of the tank. The cover of tank shall be fabricated from 3.15 thick MS sheet. The collar of the cover and manhole shall be made out of 4.00 mm MS strip. Locking arrangement for cover shall also be provided; The manhole cover shall be such fabricated so that no foreign material may enter in to the tank.

A 300 mm wide three steps ladder made of 32x32x2.5/3mm MS angle be provided at

left hand on front side of the tanker (i.e. cleaner seat side). One no. 300mm wide platform for full length at left hand be provided at appropriate level. The platform frame be made from angle iron 32x32x2.5/3mm and 2.5 mm thick MS sheet. A suitable railing of 150mm height on full length of platform shall be provided at the outer side of the platform by using 25x25x3mm Angle Iron of 25mm pipe and 2.0mm MS Sheet.

The water tanker shall be fixed on the chassis by 6 nos. suitable arranged fabricated shoes (box type brackets) from 5mm thick plates and base plate of approximate size 23 x 17 cms. and 12 mm thick OR made of suitable ISMC bolted to the chassis with suitable ‘U’ clamps (two nos. in each base). The box brackets width shall not be less than 60 mm and the bottom of the tank shall be provided with 6 mm thick and 120 mm wide saddle plates for full width of the tank as a base for the shoes (box type brackets.)

Pump set stand shall be provided at rear side of the tank.

8. Ball Bering No. 31213 must be used.

WATER TANKERS MOUNTED ON FOUR/TWO WHEEL TROLLEY

1. Outlet:

Outlet 75 mm NB class ‘A’ GI nipple of 10 length (minimum) be provided at the rear of the tank along with required 75 mm GM full way wheel valve, followed by another 20 cm length nipple for connecting a hose pipe. A Drain plug of 50 mm shall be provided at the bottom of the tank at suitable place.

2. Accessories:

The water tanker shall be provided with 2 nos. of reflectors, number plate and tool box etc. The size of tool box should be 600 mm (L) x 300 mm (W) x 300 mm (H) made of 2.5 mm MS sheet.

3. Painting & Finishing:

The tanker should be spray painted, with printing coat of red-oxide and two coat of synthetic enamel paint and color as desired by consignee. Interior of the tank should be painted with two coat of suitable primer followed by Non-poisonous white rubber paint.

4. Guarantee:-

The manufacturer shall furnish guarantee for one year against manufacturing defects leakage etc., along with tenders incorporating that in case of complaint they shall undertake satisfactory repairs within 10 days free of cast.

(S.N. Chopra) Incharge PS-III

Page 16: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

16/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/AAI/7915 Dt.: 12-04-2017

5. Inspection:-

The inspection of water tanker shall be carried out by of CSIDC, Ltd. Approved Inspection Agencies

6. Ball Bering No. 31213 must be used.

Note:- If required minor deviation/amendment in specification may be done, after taking approval from CSIDC, Ltd,.

Recommended by Technical Specification Committee Dated 23-11-2016

(S.N. Chopra)

Incharge PS-III

Page 17: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

17/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/AAI/7915 Dt.: 12-04-2017

SCHEDULE ‘B’

(SPECIAL CONDITION OF CONTRACT) ISI Pressure Cooker

Rate Contract Will be governed by the Terms & Conditions laid down in the

CSIDC FORM NO. 1 & 2

(Subas Chandra Bhagat) Incharge Marketing

Page 18: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

18/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/AAI/7915 Dt.: 12-04-2017

SCHEDULE “C”

LIST OF PARALLEL RATE CONTRACT FOR ITEM- Water Tanker

(Subas Chandra Bhagat) Incharge Marketing

S.No. Name of Tenderers Valid Up to Rate Contract No.

1. M/s Agrahari Agrotech Industries, Village-Bori, Tah & Dist.- Rajnandgaon Mob-9753072555

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/AAI/7915

2. M/s G.V. Industries, 22 A, Industrial Area, Dhar-454001 (M.P.) Mob-9425046639, 9826469388

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/G.V.I/7916

3. M/s National Engineering Works, Opp. Sirpur Lake Indore Ahmedabad Road, Indore (M.P.), Mob-07000233648

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/NEW/7920

4. M/s Netam Engineering Works, Audhogik Area, Bhakhara Road, Villa-Arjuni, Dhamtari, Mob-9406021763, 8602729134

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/NEW/7921

5. M/s New Malwa Agro & Fabricators, Plot No.-59, Sec-C, Sirgitti, Industrial Area, Bilaspur, Mob-9425046639, 7772086742

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/NMA&F/7922

6. M/s Rahul Enterprises, Office- 1016, Roshan Gagh, Pushpa Nagar Road, Esh Bagh (M.P.) Mob.-9826469388, 9826038441

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/RE/7923

7. M/s Shri Sai Steel Industries, Industrial.Area Nainpur, Surajpur, Distt.-Surajpur (C.G.) -497229 Mob.-9826649514 Email- [email protected]

17-05-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/SSSI/7919

Page 19: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

19/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/AAI/7915 Dt.: 12-04-2017

SCHEDULE – “D”

FORMAT FOR QUATERLY DRAWAL REPORT Name of the Firm __________________ I- Jan-Mar Report No. __________________ II- Apr-June Rate Contract No. __________________ III- July-Sept. Date of Submission __________________ IV- Oct - Dec Total Position of Order against Rate Contract till the submission of Report. S.No. Name of

Department Quantity and Value of Orders Received (Rs.)

Quantity and Value of Orders Executed (Rs.)

Balance Quantity and Value to be Supplied (Rs.)

Reasons

Foot 1. Value indicate should be a) Value of orders received during the quarter-Rs.

Total value inclusive of all Taxes duties and incidental b) Value of orders supplied during the quarter-Rs. Charges

2. Nil report should also be Submitted.

(Subas Chandra Bhagat) Incharge Marketing

Page 20: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

20/127

Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh Undertaking) 1st Floor Udhyog Bhawan Ring Road No. -1, Telibhanadha Raipur 492006 (C.G) EPABX No.-91771-6002071-73, Tele Fax : 91771-2583793 & 91771- 4057624 (MKT) CIN- U45203CT1981SG001853 PAN – AABCM6288N Service Tax Regn. No- AABCM6288NSD004. Website: www. csidc.in, Email : [email protected], [email protected]

No./CSIDC/MKD/PS-III/16-17/ Raipur, Dated : Registered A/D Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/G.V.I/7916 Dt.: 12-04-2017

To, M/s G.V. Industries, 22 A, Industrial Area, Dhar-454001 (M.P.) Mob-9425046639, 9826469388 [email protected] Sub :- Rate Contract for the supply of Water Tanker (Valid From dated 12-04-2017 to 11-04-2018)

Ref :- (I) This Office Tender Enquiry No. CSIDC/MKD/16-17/143/12768

(II) Your Offer acceptance along with undertaking submitted on dated 10-04-2017

Dear Sir,

You are hereby informed that your above referred tender read with subsequent letters mentioned above for the Stores specified in the Schedules annexed has been accepted. This Rate Contract will be governed by the terms and conditions brought in CSIDC Form No.1 & 2. The Rate Contract and the Schedules annexed hereto shall be the sole repository of this Rate Contract / Transaction. You are required to show the original INK-SIGNED subject Rate Contract to the satisfaction of Direct Demanding Officer who will place the supply order as per instructions contained in CSIDC form No. 2 and also to the Quality Assurance Officer for inspection purpose and to the Paying Authority at the time of getting the payment .

Conditions to be fulfilled by the Purchaser Department (DDO’s) for purchase of store from the Rate Contract holders and Quality Assurance Officer for Inspection of store before delivery :-

It is sole responsibility of the Purchase Department’s (DDO’s) and Quality Assurance Officer to comply with the following conditions as a pre-requisite before accepting delivery/conducting Inspections – (1) Purchase Department’s (DDO’s) shall ensure the validity of following documents applicable for the

Rate Contract Holder to his satisfactions :- A. NSIC Registration Certificate, Valid Operational Certificate and Competency Certificate. B. PAN Card No., Sales Tax/VAT Tax Registration (TIN).

(2) The above set of documents (As applicable) are required to be inspected by the Quality Assurance Officer before conduction inspection of store.

(3) In case, on the date of delivery OR Inspection, if any of document as mentioned above are not valid OR the validity period of which has been expired. no inspection would be conducted and also no delivery of store to be received from the Rate Contract Holder.

Incharge Marketing

Page 21: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

21/127 (4) Purchase Department’s (DDO’s)/Quality Assurance Officer would be responsible for the any

consequence which may arise due to non compliance of the above conditions and shall keep CSIDC indemnified of any such consequence.

SCHEDULES ANNEXED: 1. Schedule “A” Description of Stores, Prices, Duties / Taxes. 2. Annexure -“B” Technical Particulars of Item Water Tanker. 3. Schedule “B” Special conditions of contract (if any). 4. Schedule “C” Information to DDOs about parallel rate contracts. 5. Schedule “D” Format for Drawal Report.

Total- 18 Pages. Yours faithfully,

(Subas Chandra Bhagat) Incharge Marketing

For and on behalf of the purchaser named in CSIDC Form No.2

Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/G.V.I/7916 Dt.: 12-04-2017 +

Copy to :-

1. The Secretary, Chhattisgarh Vidhan Sabha, Raipur.

2. The Registrar, Honourable High court Chhattisgarh, Bilaspur.

3. The Accountant General Chhattisgarh State, Raipur.

4. All HODs of Chhattisgarh Govt.

5. All The Collectors, Chhattisgarh Govt.

6. The Director Treasury, Chhattisgarh Govt. with a request to circulate the copy of Rate Contract to all Direct Demanding Officers of your

institution against issue of purchase order (Indent) in favor of Rate Contract Holders of CSIDC,

7. (i) The Director Education Department (DPI) Indrawati Bhawan, Naya Raipur (C.G.) (ii) The Commissioner Tribal Welfare Department Indrawati Bhawan, Naya Raipur (C.G.) (iii) The Commissioner Directorate of Women & Child Development Indrawati Bhawan, Naya Raipur (C.G.) (iv) Principle Chief Conservator of Forest C.G. Raipur.

8. (i) CSIDC (DEPARTMENTAL TECHNICAL WING) (iii) ADG (Q & A) , DGS&D, Jeewan Tara Building 5 Parliament Street New Delhi 110001 (iii) Manager (Operation) Indian Register of Shipping, Senior MIG-2, Secter A, 1st Floor, Infront

of Bank of India Indrapuri Bhopal. (iv) Chief Engineer, PDIL, 4th floor, 4/2 Karaya Road, 67 Shekespeare Sarani, Kolkata (W.B.) (v) General Manager (Inspection) RITES Ltd., Churchgate Station Road, Second Floor, M.K.

Road, Mumbai-400020 (vi) Operations Manager SGS India Pvt, Ltd. 43, RR Arcade, Zone-2, MP Nagar, Bhopal (MP)-

462011.

9. Manager (Tender), Marketing Div., CSIDC Ltd., Raipur. He is requested to maintain a master file of Rate Contract.

10. Computer cell, CSIDC Ltd., Raipur to release Rate Contract on CSIDC website.

11. Main file of Item- “Water Tanker.”

Incharge Marketing

For and on behalf of the purchaser named in CSIDC Form No.2

Page 22: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

22/127

Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/G.V.I/7916 Dt.: 12-04-2017

SCHEDULE “A” Description of Stores, Prices, Duties/Taxes

For the supply of Item- Water Tanker as per Annexure’A’ enclosed.

1. (a) NAME AND FULL ADDRESS OF :- M/s G.V. Industries, THE FIRM 22 A, Industrial Area,

Dhar-454001 (M.P.) Mob-9425046639, 9826469388

(b) NAME AND FULL ADDRESS OF :- M/s G.V. Industries, MANUFACTURER 22 A, Industrial Area,

Dhar-454001 (M.P.)

(c) Catagery :- GEN

2. VALIDITY OF RATE CONTRACT :- From 12-04-2017 to 11-04-2018

3. DESCRIPTION OF ITEM- Water Tanker.

Item Code No.

Item Description Class Rate ( ) F.O.R. Destination

ED NA & VAT Extra if Applicable

Rate Per Unit 1 2 3

WT001 (A) Tankers Mounted On Four Wheel Trolley (With 7.50 X 16 Tyre & Tube) With Leaf Spring 5000 Liters

127139.00

WT002 4500 liters 123143.00 WT004 (A) Tankers Mounted On Four Wheel Trolley (With 7.50 X 16 Tyre &

Tube) Without Leaf Spring 5000 Liters 119060.00

WT005 4500 liters 115871.00 WT006 3500 liters 102104.00 WT007 (B) Tankers Mounted On Two Wheel Trolley With Leaf Spring 3500 Liters 90889.00 WT008 2500 Liters 80259.00 WT009 (B) Tankers Mounted On Two Wheel Trolley Without Leaf Spring 3500

Liters 88763.00

WT010 2500 Liters 73677.00 WT011 (C) Tankers Mounted On Four Wheel Trolley: (With 9x20 Tyres Tubes)

4000 Liters 122249.00

WT012 5000 Liters 127669.00 WT013 (D) Tankers Mounted On Two Wheel Trolley With Leaf Spring 4000 Liters 104178.00 WT014 4500 liters 110413.00 WT015 5000 Liters 117785.00 WT016 5500 Liters 123109.00 WT017 (D) Tankers Mounted On Two Wheel Trolley Without Leaf Spring: 4000

Liters 100457.00

WT018 4500 liters 106303.00 WT019 5000 Liters 114755.00 WT020 5500 Liters 120123.00

Note :- Technical particulars as per Annexure B enclosed

(Subas Chandra Bhagat)

Incharge Marketing

Page 23: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

23/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/G.V.I/7916 Dt.: 12-04-2017 4. TERMS OF DELIVERY : F. O. R Destination (Any where in C.G. State)

5. EXCISE DUTY : Not Applicable

6. SALES TAX /VAT : Extra, if applicable

TIN No. 23061704271 Address:-

M/s G.V. Industries, 22 A, Industrial Area, Dhar-454001 (M.P.)

7. DELIVERY PERIOD : 45 Days

8. a. ANNUAL TURN OVER/ : 2013-2014 . 202219151.00 2014-2015 . 95043264.00 2015-2016 . 99724967.00

b. MONETARY LIMIT : NM

c. INSTALLED CAPACITY : (As per NSIC Certificate Issued By Indore (M.P.)

Water Tanker

Description Annual Capacity

Water Tanker 230 Nos.

9. SLAB DISCOUNT (IF ANY) : Nil 10. PRICES : Prices are Firm and Final 11. MINIMUM QUANTITY IN : Not Mentioned. SINGLE SUPPLY ORDER 12. STATUS OF RC HOLDING : Manufacturer

FIRM 13. REGISTRATION STATUS : Manufacturer is Registered with NSIC vide No.

NSIC/GP/IND/2014/0011343, Valid up to 30-12-2018 14 BIS LICENSE : Not Applicable 15. PAYING AUTHORITY : As Mentioned in supply order to be issued by Direct Demanding Officers (DDOs).

16. PAYMENT TERMS : The payment of full 100% of prices of the stores of each consignment there-of will be made after receipt and acceptance of the stores by the consignee/interim consignee in full and good condition within 20 days as per SPR rule No.11, if the bills are in order. In case of delay in payment without any reason the department will be liable to pay interest as per prevailing bank rate. Bills are to be submitted in the prescribed form of the paying authority of purchaser / indenter and are to be supported with inspection note issued by the inspector and consignee’s Receipt Certificate.

(Subas Chandra Bhagat)

Incharge Marketing

Page 24: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

24/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/G.V.I/7916 Dt.: 12-04-2017

17 INSPECTION AUTHORITY : CSIDC (DEPARTMENTAL TECHNICAL WING) Bhilai OR ADG (Q & A) , DGS&D, Jeewan Tara Building 5 Parliament Street New Delhi 110001 OR Manager (Operation) Indian Register of Shipping Senior MIG-2, Secter A, 1st Floor, in front of Bank of India Indrapuri Bhopal (M.P.)

OR Chief Engineer, Project & Development India Ltd. 4st floor, 4/2 Karaya Road, 67 Shekespeare Sarani Kolkata (W.B.)

OR General Manager (Inspection) RITES Ltd. Churchgate Station Road, Second Floor, M.K. Road, Mumbai- 400020 (Mah) OR

Manager (Operations) SGS India Pvt. Ltd. 43, RR Arcade, Zone-2, MP Nagar, Bhopal-462011. (M.P.)

18 QUALITY ASSURANCE: CSIDC (DEPARTMENTAL TECHNICAL WING) Bhilai

Shri Sanjiv Awasthy Mob. No. 9926999936 Email- [email protected] OR Dy. Director (Q&A), DGS&D, Bhilai (C.G.) DGS&D, Sector 1, Street-10 Old Telegraph Office, Bhilai (C.G), Fax No.- 0788-2223374 OR Manager (Operation) Indian Register of Shipping Senior MIG-2, Secter A, 1st Floor, in front of Bank of India Indrapuri Bhopal. (M.P.) Shri Amit Kumar Gupta Mob. No. 8871453225] M. Nazim Athar Mob. No. 8085182339

E-mail- [email protected] OR

Chief Engineer, Project & Development India Ltd. 4st floor, 4/2 Karaya Road, 67 Shekespeare Sarani Kolkata (W.B.) Fax No. 033-22873274 OR

General Manager (Inspection) RITES Ltd. Rajnish Ahuja Western Region (Inspection) Pho. No 2201- 2523/5573 Direct 2201 7434 Mob. 08600 017717 Fax 022 22084155, 2222016219

E-mail- [email protected], [email protected] OR

Manager (Operations) SGS India Pvt. Ltd. 43, RR Arcade, Zone-2, MP Nagar, Bhopal-462011. (M.P.) Shri Jitendra Raj Mob. No. 9752848321

E-mail- [email protected]

(Subas Chandra Bhagat)

Incharge Marketing

Page 25: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

25/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/G.V.I/7916 Dt.: 12-04-2017 19. PLACE WHERE THE STORES At Manufacturer’s Factory at

ARE TO BE OFFERED FOR M/s G.V. Industries, INSPECTION 22 A, Industrial Area,

Dhar-454001 (M.P.)

20 INSPECTION CHARGES : Inspection charges 0.60%+ Service Tax As applicable to be paid extra at the time of inspection to Quality Assurance Officer which will be billed by the unit along with bill of the material and will be reimbursed by the paying authority of DDO.

21. SECURITY DEPOSIT : As per General conditions of contract, CSIDC Form No. 1, Clause 7,the Purchaser/DDOs may require the contractor to furnish a security deposit which shall be made after issue of the acceptance of the supply order within the period specified by the purchaser / DDOs. Such security deposit shall not ordinarily exceed 3% . The security shall be in form of Demand Drafts issued by any of the Scheduled Commercial Banks. No other form of security is to be accepted. The security deposit amount is to be refunded after successful completion of the supply.

22. Special Note 1. Purchasing Departments/end user will ensure to sending the copy of every Purchase order to this office. 2. Purchasing Departments/end user will ensure to Pre Dispatch inspection of stores through Inspection agency enlisted in the CSIDC Panel. 3. Purchasing Departments/end user will be responsible for ensuring the Quality of accepted stores. As per the Tech. Specification. 4. Purchasing Department/end user shall be ensure to execute the Integrity Pact between BUYER and BIDDER/ SUPPLIER in accordance with the letter vide No.799/eq-l- @2013 New Raipur Dated 10.07.2013 and 243/fo-@fu- @pkj@2013 New Raipur Dated 06.07.2013 issued by the Chief Secretary. Govt. of Chhattisgarh. 5. Purchasing Department/end user will ensure to issue the

Purchase Order in accordance with the Store Purchase Rules-2002 (As Amended) vide Clause No.-13

(Subas Chandra Bhagat) Incharge Marketing

Page 26: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

26/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/G.V.I/7916 Dt.: 12-04-2017

Annexure-B CSIDC/MKD/TECH/2016-17/28

SPECIFICATION FOR WATER TANKER MOUNTED ON FOUR / TWO WHEEL TROLLEY

TSC 23-11-2016

(E) SPECIFICATION OF PRODUCTS

(A) TANKERS MOUNTED ON FOUR WHEEL TROLLEY (WITH 7.50 X 16 TYRE & TUBE) WITH LEAF SPRING OR WITHOUT LEAF SPRING

1. Chassis:

The Chassis shall be fabricated as per standard practice to mount the MS tank. All the joint shall be welded with gusset plates wherever required as per standard practice.

The Chassis frame shall have two longitudinal member and 5 cross members of channel

section of size 125 x 65 mm (ISMC) for 4500 & 5000 lts. Capacity. For 3500 lts. Capacity the chassis frame shall have two longitudinal members and 4 cross members of channel section of size 100 x 50 mm (ISMC) The overall approximate dimensions of various tanker trolley chassis shall be as under:- -----------------------------------------------------------------------------------------------------

S.No. Approx.Cap Length Width -----------------------------------------------------------------------------------------------------

1. 5000 liters 4 metres 1.00 mtr. 2. 4500 liters 4 meters 1.00 mtr. 3. 3500 liters 3.5 meters 1.00 mtr.

-----------------------------------------------------------------------------------------------------

2. Turn table:

The turn table frame shall be made out of 100x50mm (ISMC) MS channel with cross support, fixed with double rings fabricated from Angle Iron 40x40x6 mm and with 40mm diameter centre pin with suitable washer and locking arrangement.

3. Draw Bar:

Draw bar shall be in triangular construction made out of ISMC of size 100x50 mm with spring loaded eyehook made of 40mm dia MS bar.

The straight length of draw bar should be 150 cms including eye hook. Draw bar shall be hinged with the frame of turn table by 500 x 25mm Ms round bar having locking arrangement at both the end.

4. Axle & Brake assembly:

Axle shall be made from 63 x 63mm square bar with both the end machined, threaded and fitted with hubs and hexagonal lock nut, fitted with twin taper roller bearings, and provided with grease nipples for greasing the moving parts. For braking mechanical-internal expanding type brakes with suitable drums. hand operated, on rear wheels compete, with steel rod, clamps, springs and hand lever be provided.

(S.N. Chopra)

Incharge PS-III

Page 27: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

27/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/G.V.I/7916 Dt.: 12-04-2017

5. Leaf Spring:

Four sets of leaf spring consisting of 13 leaves of size minimum 70 x 10mm, 1000mm long (distance between two pin) of alloy steel shall be provided. These leaf spring shall be fixed with frame by means of complete cast iron bracket assembly.

6. Tyres, tubes & wheel Assembly :

Four number tyre of 7.50 x 16 and tubes of standard make, Shall be provided with double plated rims 5mm thick with 5/6 nos. holes.

7. Water tanker:

The Water Tanker shall have capacity of 5000, 4500 & 3500 litres approx., and shall be manufactured in elliptical shape/ semi elliptical shape. The approx size of Water Tanker shall be as follows:- ----------------------------------------------------------------------------------------------------------- S. No. Approx. Major Axis Minor Axis Length ----------------------------------------------------------------------------------------------------------- 1. 5000 lit. 1.95 mtrs. 1.05 mtrs. 3.6 mtrs. 2. 4500 lit. 1.75 mtrs. 1.05 mtrs. 3.6 mtrs. 3. 3500 lit.. 1.5 mtrs 1.05 mtrs. 3.0 mtrs -----------------------------------------------------------------------------------------------------------

The tank shall be made out of 3.15mm thick MS sheet, and end plates of 4.0mm thick MS plate. End plate shall be maximum in two piece.

The tank shall be reinforced from inside by welding four numbers of elliptical rings made of 40 x 40 x 6mm MS angle one at both ends and two in between at suitable distance (total 04 on.) for 4500 & 5000 lts capacity. For 3500 lts capacity angle rings shall be provided at both ends and one at the middle (total 03 no.)

Two nos. baffle plate of 3.15mm thick MS sheet shall be provided in side the tank. These plates shall be properly welded with the central ring as per the standard practice. The height of baffle plate shall be 20cm. More than half of the height of tank. For 3500 lts capacity only one baffle plate be provided.

8. Manhole:

Two manhole with hinged cover shall be provided at the top of the tank. The cover of tank shall be fabricated from 3.15 thick MS sheet. The collar of the cover and manhole shall be made out of 4.00 mm MS strip. Locking arrangement for cover shall be provided; The manhole covers shall be such fabricated so that no foreign material may enter into the tank.

A 300 mm wide five steps ladder made of 32 x 32 x 2.5/3mm Ms angle be provided at left hand on rear side of the tanker (i.e. cleaner seat side). One no. 300 mm wide platform for full length at left hand be provided at appropriate level. The platform frame be made from Angle Iron 32 x 32 x2.5/3mm and 2.5 mm thick MS sheet. A suitable railing of 150 mm height on full length of platform shall be provided at the outer side of the platform by using 25x25x2.5/3mm Angle Iron or 25mm pipe and 2.0 mm MS sheet.

(S.N. Chopra) Incharge PS-III

Page 28: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

28/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/G.V.I/7916 Dt.: 12-04-2017

The rear wheels shall be covered with mudguards fabricated out of 1.6mm thick MS sheets,

as per standard practice.

The Water Tanker shall be fixed on the chassis by 8 nos. suitable arranged fabricated shoes (box type brackets) from 5mm thick plates and base plate of approximate size 23x17 cms. and 12mm thick OR made of suitable ISMC bolted to the chassis with suitable ‘U’ clamps (two nos. in each base) The box brackets width shall not be less than 60mm and the bottom of the tank shall be provided with 6 mm thick and 120mm wide saddle plates for full width of the tank as a base for the shoes (box type brackets).

9. Ball Bering No. 31213 must be used. (B) TANKERS MOUNTED ON TWO WHEEL TROLLEY WITH LEAF SPRING OR

WITHOUT LEAF SPRING 1. Chassis:

The Chassis shall be fabricated as per standard practice to mount the MS tank. All the joint shall be welded with gusset plates wherever required as per standard practice.

The Chassis frame shall have two longitudinal member and 4 cross members of channel

section of size 100 x 50 mm (ISMC).

The overall approximate dimensions of various tanker trolley chassis shall be as under:- -----------------------------------------------------------------------------------------------------

S.No. Approx.Cap Length Width -----------------------------------------------------------------------------------------------------

1. 3500 liters 3.0 metres 0.80 mtr. 2. 2500 liters 2.5 meters 0.80 mtr.

----------------------------------------------------------------------------------------------------- 2. Draw bar:

Draw bar shall be in triangular construction made out of MS channel of size 100 x 50 mm with spring loaded eyehook made of 40 mm dia MS bar.

The straight length of draw bar should be 150 cms including eye hook.

3. Axle & Brake assembly:

Axle shall be made from 63 x 63mm square bar with both the end machined and threaded and provided with iron hubs and hexagonal lock nut, fitted with twin taper roller bearings and provided with grease nipples for greasing the moving parts.

4. Leaf spring:

Two sets of leaf spring consisting of 13 leaves of size 70 x 10mm minimum 1000 mm long (distance between two pin) of alloy steel shall be provided. These leaf spring shall be fixed with frame by means of complete cast iron bracket assembly.

5. Tyres, tubes & wheel Assembly:

(S.N. Chopra)

Incharge PS-III

Page 29: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

29/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/G.V.I/7916 Dt.: 12-04-2017

Two number tyres of 7.50 x 16 and tubes of standard make shall be provided with double plated rims 5 mm thick with 5/6 nos. holes for 2500 lts. Capacity tanker. For 3500 lts. Capacity two number tyres of 9x16 and tubes of standard make shall be provided.

6. Water Tanker:

The Water Tanker Should have capacity of 2500 & 3500 liters approx. Manufactured in elliptical. Shape. The approx. size of Water Tanker are as follows :-

-------------------------------------------------------------------------------------------------------------- S.No. Approx.Cap Major Axis Minor Axis Length -------------------------------------------------------------------------------------------------------------- 1. 3500 liters 1.5 mtrs 1.05 mtrs 3.0 mtrs. 2. 2500 liters 1.20 mtrs 1.05 mtrs 2.5 mtrs. --------------------------------------------------------------------------------------------------------------

The tank shall be made out of 3.15 mm thick MS sheet, and end plates of 4.0 thick MS plate. End plate should be maximum two pieces.

The tank shall be reinforced from inside by welding three numbers of elliptical rings made of 40 x 40 x 6mm MS angle one at both ends and one in between at suitable distance.

One baffle plate of 3.15mm shall be provided inside the tank. These plates shall be properly welded with the central ring as per the standard practice. The height of baffle plate shall be 20 cm more than half of the height of tank.

7. Manhole:

One manhole with hinged cover shall be provided at the top of the tank. The cover of tank shall be fabricated from 3.15 thick MS sheet. The collar of the cover and manhole shall be made out of 4.00 mm MS strip. Locking arrangement for cover shall also be provided; The manhole cover shall be such fabricated so that no foreign material may enter in to the tank.

A 300 mm wide three steps ladder made of 32x32x2.5/3mm MS angle be provided at left hand on front side of the tanker (i.e. cleaner seat side). One no. 300mm wide platform for full length at left hand be provided at appropriate level. The platform frame be made from angle iron 32x32x2.5/3mm and 2.5 mm thick MS sheet. A suitable railing of 150mm height on full length of platform shall be provided at the outer side of the platform by using 25x25x3mm Angle Iron of 25mm pipe and 2.0mm MS Sheet.

The water tanker shall be fixed on the chassis by 6 nos. suitable arranged fabricated shoes (box type brackets) from 5mm thick plates and base plate of approximate size 23 x 17 cms. and 12 mm thick OR made of suitable ISMC bolted to the chassis with suitable ‘U’ clamps (two nos. in each base). The box brackets width shall not be less than 60 mm and the bottom of the tank shall be provided with 6 mm thick and 120 mm wide saddle plates for full width of the tank as a base for the shoes (box type brackets.)

8. Ball Bering No. 31213 must be used.

(C) TANKERS MOUNTED ON FOUR WHEEL TROLLEY: (WITH 9X20 TYRES TUBES)

1. Chassis: The Chassis shall be fabricated as per standard practice to mount the MS tank. All the joint

shall be welded with gusset plates wherever required as per standard practice.

(S.N. Chopra)

Incharge PS-III

Page 30: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

30/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/G.V.I/7916 Dt.: 12-04-2017

The chassis frame shall have two longitudinal member and 3 cross members of channel section of size 150x75mm (ISMC) for 4000 & 5000 It. Capacity.

The width of the chassis frame shall be of 1.0mt and length shall be equal to the length of the tank.

2. Turn table:

The turn table frame shall be made out of 100x50mm (ISMC or equivalent) MS channel with cross support, fixed with double rings fabricated out of Angle Iron 40x40x6 mm and with 40mm diameter centre pin with suitable washer and locking arrangement.

3. Draw Bar:

Draw bar shall be in triangular construction made out of Ms Channel of size 100x50 mm with spring loaded eyehook made of 40mm dia MS bar.

The straight length of draw bar should be 150 cms including eye hook. Draw bar shall be hinged with the frame of turn table by 100x25mm MS round bar having locking arrangement at both the end.

4. Axle & Brake assembly:

Axle shall be made from 63x63mm square bar of 1750mm length with both the end machined and threaded and provided with iron hubs and hexagonal lock nut, fitted with twin taper roller bearings, and provided with grease nipples for greasing the moving parts. For braking mechanical-internal expanding type brakes with suitable drums, hand operated, on rear wheels compete, with steel rod, clamps, springs and hand lever be provided.

5. Leaf Spring:

Four sets of leaf spring consisting of 13 leaves of size 70x11 mm minimum 1000mm long (distance between two pin) of alloy steel shall be provided. These leaf spring shall be fixed with frame by means of complete cast iron bracket assembly.

6. Tyres, tubes & wheel Assembly :

Four number tyre of 9 x 20 and tubes of standard make. Shall be provided with double plated rims 5 mm thick with 5/6 nos. holes. For four wheel trolley.

7. Water tanker:

The Water Tanker shall have capacity of 5000 & 4000 litres approx. manufactured in semi elliptical shape.

The minor axis of the tank shall be of 1.05 mtr. The manufacturer shall design major axis

and length of the semi elliptical tank accordingly. The tank shall be made out of 3.15 mm thick MS sheet, and end plates of 4.0 thick MS plate.

End plate should be maximum two pieces.

(S.N. Chopra)

Incharge PS-III

Page 31: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

31/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/G.V.I/7916 Dt.: 12-04-2017

The tank shall be reinforced from inside by welding three numbers of elliptical rings made of 40 x 40 x 6mm MS angle one at both ends and one in between at suitable distance.

Two baffle plate of 3.15mm shall be provided in side the tank. These plates shall be properly

welded with the central ring as per the standard practice. The height of baffle plate shall be 20 cm more than half of the height of tank.

8. Manhole:

Two manhole with hinged cover shall be provided at the top of the tank. The cover of tank shall be fabricated from 3.15 thick MS sheet. The collar of the cover and manhole shall be made out of 4.00 mm MS strip. Locking arrangement for cover shall also be provided; The manhole cover shall be such fabricated so that no foreign material may enter in to the tank.

A 300 mm wide three steps ladder made of 30x30x3mm MS angle be provided at left hand

on front side of the tanker. One no. 300mm wide platform for full length at left hand be provided at appropriate level. The platform frame be made from angle iron 35x35x3mm and 2.5 mm thick MS sheet. A suitable railing of 150mm height on full length of platform shall be provided at the outer side of the platform by using 25x25x3mm Angle Iron of 25mm pipe and 2.0mm MS Sheet.

The water tanker shall be fixed on the chassis by 8 nos. suitable arranged fabricated shoes

(box type brackets) from 5mm thick plates and base plate of approximate size 23 x 17 cms. and 12mm thick bolted to the chassis or made of 100x50mm channel properly covered with sheet of 3.15mm suitable ‘U’ clamps (two nos. in each base). The box brackets width shall not be less than 60 mm and the bottom of the tank shall be provided with 6 mm thick and 120 mm wide saddle plates for full width of the tank as a base for the shoes (box type brackets.)

9. Ball Bering No. –31213 must be used. (D) TANKERS MOUNTED ON TWO WHEEL TROLLEY WITH LEAF SPRING OF

WITHOUT LEAF SPRING: 1. Chassis:

The Chassis shall be fabricated as per standard practice to mount the MS tank. All the joint shall be welded with gusset plates wherever required as per standard practice.

The Chassis frame shall have two longitudinal members and 4 cross members of channel

section of size 150 x 75 mm (ISMC) The overall approximate dimensions of various tanker trolley chassis shall be as under:- -----------------------------------------------------------------------------------------------------

S.No. Approx.Cap Length Width -----------------------------------------------------------------------------------------------------

1. 4000 liters 3.3 metres 1.2 mtr. 2. 4500 liters 3.5 meters 1.2 mtr. 3. 5000 liters 3.5 meters 1.2 mtr. 4. 5500 liters 3.7 metres 1.2 mtr.

-----------------------------------------------------------------------------------------------------

(S.N. Chopra) Incharge PS-III

Page 32: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

32/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/G.V.I/7916 Dt.: 12-04-2017 WATER TANKERS MOUNTED ON FOUR/TWO WHEEL TROLLEY 2. Draw Bar:

Draw bar shall be in triangular construction made out of MS channel of size 150x75 mm with spring loaded eyehook made of 40mm dia MS bar.

The minimum straight length of draw bar should be 150 cms including eye hook.

3. Axle & Brake assembly:

Axle shall be made from 72 x 72mm square bar with both the end machined and threaded and provided with iron hubs and hexagonal lock nut, fitted with twin taper roller bearings and provided with grease nipples for greasing the moving parts.

4. Leaf Spring:

Two sets of leaf spring consisting of 13 leaves of 4000 & 4500 Ltr. And 19 leaves for 5000 & 5500 ltr. Cap. Of size minimum 70 x 10mm minimum 900mm long (distance between two pin) of alloy steel shall be provided. These leaf spring shall be fixed with frame by means of complete cast iron bracket assembly.

5. Tyres, tubes & wheel Assembly :

Two number tyre of 9 x16 / 9x16 and tubes of standard make Shall be provided with double plated rims 5mm thick with 8 nos. holes.

6. Water tanker:

The Water Tanker should have capacity of 5000, 5500 litres approx. manufactured in elliptical shape. The approx size of Water Tanker are as follows:- ----------------------------------------------------------------------------------------------------------- S. No. Approx. Major Axis Minor Axis Length ----------------------------------------------------------------------------------------------------------- 1. 4000 lit. 1.65 meters 1.11 mtrs. 2.8 mtrs. 2. 4500 lit. 1.70 meters 1.13 mtrs. 3.0 mtrs. 3. 5000 lit. 1.80 meters 1.18 mtrs. 3.0 mtrs 4. 5500 lit. 1.80 meters 1.22 mtrs. 3.2 mtrs. -----------------------------------------------------------------------------------------------------------

WATER TANKERS MOUNTED ON FOUR/TWO WHEEL TROLLEY

The tank shall be made out of 3.15mm thick MS sheet, and end plates of 4.0mm thick MS plate. End plate should be in maximum two pieces.

The tank shall be reinforced form inside by welding three numbers of elliptical rings made of

40x40x6mm MS Angle one at both ends and one in between at suitable distance.

One baffle plate of 3.15mm shall be provided in side the tank. These plates shall be properly welded with the central ring as per the standard practice. The height of baffle plate shall be 20cm. more than half of the minor axis of tank.

(S.N. Chopra)

Incharge PS-III

Page 33: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

33/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/G.V.I/7916 Dt.: 12-04-2017 7. Manhole:

One manhole with hinged cover shall be provided at the top of the tank. The cover of tank shall be fabricated from 3.15 thick MS sheet. The collar of the cover and manhole shall be made out of 4.00 mm MS strip. Locking arrangement for cover shall also be provided; The manhole cover shall be such fabricated so that no foreign material may enter in to the tank.

A 300 mm wide three steps ladder made of 32x32x2.5/3mm MS angle be provided at

left hand on front side of the tanker (i.e. cleaner seat side). One no. 300mm wide platform for full length at left hand be provided at appropriate level. The platform frame be made from angle iron 32x32x2.5/3mm and 2.5 mm thick MS sheet. A suitable railing of 150mm height on full length of platform shall be provided at the outer side of the platform by using 25x25x3mm Angle Iron of 25mm pipe and 2.0mm MS Sheet.

The water tanker shall be fixed on the chassis by 6 nos. suitable arranged fabricated shoes (box type brackets) from 5mm thick plates and base plate of approximate size 23 x 17 cms. and 12 mm thick OR made of suitable ISMC bolted to the chassis with suitable ‘U’ clamps (two nos. in each base). The box brackets width shall not be less than 60 mm and the bottom of the tank shall be provided with 6 mm thick and 120 mm wide saddle plates for full width of the tank as a base for the shoes (box type brackets.)

Pump set stand shall be provided at rear side of the tank.

8. Ball Bering No. 31213 must be used.

WATER TANKERS MOUNTED ON FOUR/TWO WHEEL TROLLEY

1. Outlet:

Outlet 75 mm NB class ‘A’ GI nipple of 10 length (minimum) be provided at the rear of the tank along with required 75 mm GM full way wheel valve, followed by another 20 cm length nipple for connecting a hose pipe. A Drain plug of 50 mm shall be provided at the bottom of the tank at suitable place.

2. Accessories:

The water tanker shall be provided with 2 nos. of reflectors, number plate and tool box etc. The size of tool box should be 600 mm (L) x 300 mm (W) x 300 mm (H) made of 2.5 mm MS sheet.

3. Painting & Finishing:

The tanker should be spray painted, with printing coat of red-oxide and two coat of synthetic enamel paint and color as desired by consignee. Interior of the tank should be painted with two coat of suitable primer followed by Non-poisonous white rubber paint.

4. Guarantee:-

The manufacturer shall furnish guarantee for one year against manufacturing defects leakage etc., along with tenders incorporating that in case of complaint they shall undertake satisfactory repairs within 10 days free of cast.

(S.N. Chopra) Incharge PS-III

Page 34: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

34/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/G.V.I/7916 Dt.: 12-04-2017

5. Inspection:-

The inspection of water tanker shall be carried out by of CSIDC, Ltd. Approved Inspection Agencies

6. Ball Bering No. 31213 must be used.

Note:- If required minor deviation/amendment in specification may be done, after taking approval from CSIDC, Ltd,.

Recommended by Technical Specification Committee Dated 23-11-2016

(S.N. Chopra)

Incharge PS-III

Page 35: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

35/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/G.V.I/7916 Dt.: 12-04-2017

SCHEDULE ‘B’

(SPECIAL CONDITION OF CONTRACT) ISI Pressure Cooker

Rate Contract Will be governed by the Terms & Conditions laid down in the

CSIDC FORM NO. 1 & 2

(Subas Chandra Bhagat) Incharge Marketing

Page 36: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

36/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/G.V.I/7916 Dt.: 12-04-2017

SCHEDULE “C” LIST OF PARALLEL RATE CONTRACT FOR ITEM- Water Tanker

(Subas Chandra Bhagat) Incharge Marketing

S.No. Name of Tenderers Valid Up to Rate Contract No.

1. M/s Agrahari Agrotech Industries, Village-Bori, Tah & Dist.- Rajnandgaon Mob-9753072555

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/AAI/7915

2. M/s G.V. Industries, 22 A, Industrial Area, Dhar-454001 (M.P.) Mob-9425046639, 9826469388

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/G.V.I/7916

3. M/s National Engineering Works, Opp. Sirpur Lake Indore Ahmedabad Road, Indore (M.P.), Mob-07000233648

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/NEW/7920

4. M/s Netam Engineering Works, Audhogik Area, Bhakhara Road, Villa-Arjuni, Dhamtari, Mob-9406021763, 8602729134

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/NEW/7921

5. M/s New Malwa Agro & Fabricators, Plot No.-59, Sec-C, Sirgitti, Industrial Area, Bilaspur, Mob-9425046639, 7772086742

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/NMA&F/7922

6. M/s Rahul Enterprises, Office- 1016, Roshan Gagh, Pushpa Nagar Road, Esh Bagh (M.P.) Mob.-9826469388, 9826038441

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/RE/7923

7. M/s Shri Sai Steel Industries, Industrial.Area Nainpur, Surajpur, Distt.-Surajpur (C.G.) -497229 Mob.-9826649514 Email- [email protected]

17-05-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/SSSI/7919

Page 37: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

37/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/G.V.I/7916 Dt.: 12-04-2017

SCHEDULE – “D”

FORMAT FOR QUATERLY DRAWAL REPORT Name of the Firm __________________ I- Jan-Mar Report No. __________________ II- Apr-June Rate Contract No. __________________ III- July-Sept. Date of Submission __________________ IV- Oct - Dec Total Position of Order against Rate Contract till the submission of Report. S.No. Name of

Department Quantity and Value of Orders Received (Rs.)

Quantity and Value of Orders Executed (Rs.)

Balance Quantity and Value to be Supplied (Rs.)

Reasons

Foot 1. Value indicate should be a) Value of orders received during the quarter-Rs.

Total value inclusive of all Taxes duties and incidental b) Value of orders supplied during the quarter-Rs. Charges

2. Nil report should also be Submitted.

(Subas Chandra Bhagat) Incharge Marketing

Page 38: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

38/127

Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh Undertaking) 1st Floor Udhyog Bhawan Ring Road No. -1, Telibhanadha Raipur 492006 (C.G) EPABX No.-91771-6002071-73, Tele Fax : 91771-2583793 & 91771- 4057624 (MKT) CIN- U45203CT1981SG001853 PAN – AABCM6288N Service Tax Regn. No- AABCM6288NSD004. Website: www. csidc.in, Email : [email protected], [email protected]

No./CSIDC/MKD/PS-III/16-17/ Raipur, Dated : Registered A/D Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7920 Dt.: 12-04-2017

To, M/s National Engineering Works, Opp. Sirpur Lake Indore Ahmedabad Road, Indore, (M.P.) Mob-07000233648 Sub :- Rate Contract for the supply of Water Tanker (Valid From dated 12-04-2017 to 11-04-2018)

Ref :- (I) This Office Tender Enquiry No. CSIDC/MKD/16-17/143/12768

(II) Your Offer acceptance along with undertaking submitted on dated 10-04-2017

Dear Sir,

You are hereby informed that your above referred tender read with subsequent letters mentioned above for the Stores specified in the Schedules annexed has been accepted. This Rate Contract will be governed by the terms and conditions brought in CSIDC Form No.1 & 2. The Rate Contract and the Schedules annexed hereto shall be the sole repository of this Rate Contract / Transaction. You are required to show the original INK-SIGNED subject Rate Contract to the satisfaction of Direct Demanding Officer who will place the supply order as per instructions contained in CSIDC form No. 2 and also to the Quality Assurance Officer for inspection purpose and to the Paying Authority at the time of getting the payment .

Conditions to be fulfilled by the Purchaser Department (DDO’s) for purchase of store from the Rate Contract holders and Quality Assurance Officer for Inspection of store before delivery :-

It is sole responsibility of the Purchase Department’s (DDO’s) and Quality Assurance Officer to comply with the following conditions as a pre-requisite before accepting delivery/conducting Inspections – (1) Purchase Department’s (DDO’s) shall ensure the validity of following documents applicable for the

Rate Contract Holder to his satisfactions :- A. NSIC Registration Certificate, Valid Operational Certificate and Competency Certificate. B. PAN Card No., Sales Tax/VAT Tax Registration (TIN).

(2) The above set of documents (As applicable) are required to be inspected by the Quality Assurance Officer before conduction inspection of store.

(3) In case, on the date of delivery OR Inspection, if any of document as mentioned above are not valid OR the validity period of which has been expired. no inspection would be conducted and also no delivery of store to be received from the Rate Contract Holder.

Incharge Marketing

Page 39: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

39/127 (4) Purchase Department’s (DDO’s)/Quality Assurance Officer would be responsible for the any

consequence which may arise due to non compliance of the above conditions and shall keep CSIDC indemnified of any such consequence.

SCHEDULES ANNEXED: 1. Schedule “A” Description of Stores, Prices, Duties / Taxes. 2. Annexure -“B” Technical Particulars of Item Water Tanker. 3. Schedule “B” Special conditions of contract (if any). 4. Schedule “C” Information to DDOs about parallel rate contracts. 5. Schedule “D” Format for Drawal Report.

Total- 18 Pages. Yours faithfully,

(Subas Chandra Bhagat) Incharge Marketing

For and on behalf of the purchaser named in CSIDC Form No.2

Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7920 Dt.: 12-04-2017 +

Copy to :-

1. The Secretary, Chhattisgarh Vidhan Sabha, Raipur.

2. The Registrar, Honourable High court Chhattisgarh, Bilaspur.

3. The Accountant General Chhattisgarh State, Raipur.

4. All HODs of Chhattisgarh Govt.

5. All The Collectors, Chhattisgarh Govt.

6. The Director Treasury, Chhattisgarh Govt. with a request to circulate the copy of Rate Contract to all Direct Demanding Officers of your

institution against issue of purchase order (Indent) in favor of Rate Contract Holders of CSIDC,

7. (i) The Director Education Department (DPI) Indrawati Bhawan, Naya Raipur (C.G.) (ii) The Commissioner Tribal Welfare Department Indrawati Bhawan, Naya Raipur (C.G.) (iii) The Commissioner Directorate of Women & Child Development Indrawati Bhawan, Naya Raipur (C.G.) (iv) Principle Chief Conservator of Forest C.G. Raipur.

8. (i) CSIDC (DEPARTMENTAL TECHNICAL WING) (ii) ADG (Q & A) , DGS&D, Jeewan Tara Building 5 Parliament Street New Delhi 110001 (iii) Manager (Operation) Indian Register of Shipping, Senior MIG-2, Secter A, 1st Floor, Infront

of Bank of India Indrapuri Bhopal. (iv) Chief Engineer, PDIL, 4th floor, 4/2 Karaya Road, 67 Shekespeare Sarani, Kolkata (W.B.) (v) General Manager (Inspection) RITES Ltd., Churchgate Station Road, Second Floor, M.K.

Road, Mumbai-400020 (vi) Operations Manager SGS India Pvt, Ltd. 43, RR Arcade, Zone-2, MP Nagar, Bhopal (MP)-

462011.

9. Manager (Tender), Marketing Div., CSIDC Ltd., Raipur. He is requested to maintain a master file of Rate Contract.

10. Computer cell, CSIDC Ltd., Raipur to release Rate Contract on CSIDC website.

11. Main file of Item- “Water Tanker.”

Incharge Marketing

For and on behalf of the purchaser named in CSIDC Form No.2

Page 40: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

40/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7920 Dt.: 12-04-2017

SCHEDULE “A” Description of Stores, Prices, Duties/Taxes

For the supply of Item- Water Tanker as per Annexure’A’ enclosed.

1. (a) NAME AND FULL ADDRESS OF :- M/s National Engineering Works, THE FIRM Opp. Sirpur Lake Indore Ahmedabad Road,

Indore, (M.P.) Mob-07000233648

(b) NAME AND FULL ADDRESS OF :- M/s National Engineering Works, MANUFACTURER Opp. Sirpur Lake Indore Ahmedabad Road,

Indore, (M.P.)

(c) Catagery :- GEN

2. VALIDITY OF RATE CONTRACT :- From 12-04-2017 to 11-04-2018

3. DESCRIPTION OF ITEM- Water Tanker.

Item Code No.

Item Description Class Rate ( ) F.O.R. Destination

ED NA & VAT Extra if Applicable

Rate Per Unit 1 2 3

WT001 (A) Tankers Mounted On Four Wheel Trolley (With 7.50 X 16 Tyre & Tube) With Leaf Spring 5000 Liters

127139.00

WT002 4500 liters 123143.00 WT004 (A) Tankers Mounted On Four Wheel Trolley (With 7.50 X 16 Tyre &

Tube) Without Leaf Spring 5000 Liters 119060.00

WT005 4500 liters 115871.00 WT006 3500 liters 102104.00 WT007 (B) Tankers Mounted On Two Wheel Trolley With Leaf Spring 3500 Liters 90889.00 WT008 2500 Liters 80259.00 WT009 (B) Tankers Mounted On Two Wheel Trolley Without Leaf Spring 3500

Liters 88763.00

WT010 2500 Liters 73677.00 WT011 (C) Tankers Mounted On Four Wheel Trolley: (With 9x20 Tyres Tubes)

4000 Liters 122249.00

WT012 5000 Liters 127669.00 WT013 (D) Tankers Mounted On Two Wheel Trolley With Leaf Spring 4000 Liters 104178.00 WT014 4500 liters 110413.00 WT015 5000 Liters 117785.00 WT016 5500 Liters 123109.00 WT017 (D) Tankers Mounted On Two Wheel Trolley Without Leaf Spring: 4000

Liters 100457.00

WT018 4500 liters 106303.00 WT019 5000 Liters 114755.00 WT020 5500 Liters 120123.00

Note :- Technical particulars as per Annexure B enclosed

(Subas Chandra Bhagat)

Incharge Marketing

Page 41: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

41/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7920 Dt.: 12-04-2017 4. TERMS OF DELIVERY : F. O. R Destination (Any where in C.G. State)

5. EXCISE DUTY : Not Applicable

6. SALES TAX /VAT : Extra, if applicable

TIN No. 23689018211 Address:-

M/s National Engineering Works, Opp. Sirpur Lake Indore Ahmedabad Road, Indore, (M.P.)

7. DELIVERY PERIOD : 45 Days

8. a. ANNUAL TURN OVER/ : 2013-14 . 106972887.00 2014-15 . 30062269.00 2015-16 . 118570218.00

b. MONETARY LIMIT : NM

c. INSTALLED CAPACITY : (As per NSIC Certificate Issued By Indore (M.P.)

Water Tanker

Description Annual Capacity

Water Tanker 480 Nos.

9. SLAB DISCOUNT (IF ANY) : Nil 10. PRICES : Prices are Firm and Final 11. MINIMUM QUANTITY IN : Not Mentioned. SINGLE SUPPLY ORDER 12. STATUS OF RC HOLDING : Manufacturer

FIRM 13. REGISTRATION STATUS : Manufacturer is Registered with NSIC vide No.

NSIC/GP/IND/2015/0015707, Valid up to 07-05-2017 14 BIS LICENSE : Not Applicable 15. PAYING AUTHORITY : As Mentioned in supply order to be issued by Direct Demanding Officers (DDOs).

16. PAYMENT TERMS : The payment of full 100% of prices of the stores of each consignment there-of will be made after receipt and acceptance of the stores by the consignee/interim consignee in full and good condition within 20 days as per SPR rule No.11, if the bills are in order. In case of delay in payment without any reason the department will be liable to pay interest as per prevailing bank rate. Bills are to be submitted in the prescribed form of the paying authority of purchaser / indenter and are to be supported with inspection note issued by the inspector and consignee’s Receipt Certificate.

(Subas Chandra Bhagat)

Incharge Marketing

Page 42: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

42/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7920 Dt.: 12-04-2017

17 INSPECTION AUTHORITY : CSIDC (DEPARTMENTAL TECHNICAL WING) Bhilai OR ADG (Q & A) , DGS&D, Jeewan Tara Building 5 Parliament Street New Delhi 110001 OR Manager (Operation) Indian Register of Shipping Senior MIG-2, Secter A, 1st Floor, in front of Bank of India Indrapuri Bhopal (M.P.)

OR Chief Engineer, Project & Development India Ltd. 4st floor, 4/2 Karaya Road, 67 Shekespeare Sarani Kolkata (W.B.)

OR General Manager (Inspection) RITES Ltd. Churchgate Station Road, Second Floor, M.K. Road, Mumbai- 400020 (Mah) OR

Manager (Operations) SGS India Pvt. Ltd. 43, RR Arcade, Zone-2, MP Nagar, Bhopal-462011. (M.P.)

18 QUALITY ASSURANCE: CSIDC (DEPARTMENTAL TECHNICAL WING) Bhilai

Shri Sanjiv Awasthy Mob. No. 9926999936 Email- [email protected] OR Dy. Director (Q&A), DGS&D, Bhilai (C.G.) DGS&D, Sector 1, Street-10 Old Telegraph Office, Bhilai (C.G), Fax No.- 0788-2223374 OR Manager (Operation) Indian Register of Shipping Senior MIG-2, Secter A, 1st Floor, in front of Bank of India Indrapuri Bhopal. (M.P.) Shri Amit Kumar Gupta Mob. No. 8871453225] M. Nazim Athar Mob. No. 8085182339

E-mail- [email protected] OR

Chief Engineer, Project & Development India Ltd. 4st floor, 4/2 Karaya Road, 67 Shekespeare Sarani Kolkata (W.B.) Fax No. 033-22873274 OR

General Manager (Inspection) RITES Ltd. Rajnish Ahuja Western Region (Inspection) Pho. No 2201- 2523/5573 Direct 2201 7434 Mob. 08600 017717 Fax 022 22084155, 2222016219

E-mail- [email protected], [email protected] OR

Manager (Operations) SGS India Pvt. Ltd. 43, RR Arcade, Zone-2, MP Nagar, Bhopal-462011. (M.P.) Shri Jitendra Raj Mob. No. 9752848321

E-mail- [email protected]

(Subas Chandra Bhagat)

Incharge Marketing

Page 43: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

43/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7920 Dt.: 12-04-2017 19. PLACE WHERE THE STORES At Manufacturer’s Factory at

ARE TO BE OFFERED FOR M/s National Engineering Works, INSPECTION Opp. Sirpur Lake Indore Ahmedabad Road,

Indore, (M.P.)

20 INSPECTION CHARGES : Inspection charges 0.60%+ Service Tax As applicable to be paid extra at the time of inspection to Quality Assurance Officer which will be billed by the unit along with bill of the material and will be reimbursed by the paying authority of DDO.

21. SECURITY DEPOSIT : As per General conditions of contract, CSIDC Form No. 1, Clause 7,the Purchaser/DDOs may require the contractor to furnish a security deposit which shall be made after issue of the acceptance of the supply order within the period specified by the purchaser / DDOs. Such security deposit shall not ordinarily exceed 3% . The security shall be in form of Demand Drafts issued by any of the Scheduled Commercial Banks. No other form of security is to be accepted. The security deposit amount is to be refunded after successful completion of the supply.

22. Special Note 1. Purchasing Departments/end user will ensure to sending the copy of every Purchase order to this office. 2. Purchasing Departments/end user will ensure to Pre Dispatch inspection of stores through Inspection agency enlisted in the CSIDC Panel. 3. Purchasing Departments/end user will be responsible for ensuring the Quality of accepted stores. As per the Tech. Specification. 4. Purchasing Department/end user shall be ensure to execute the Integrity Pact between BUYER and BIDDER/ SUPPLIER in accordance with the letter vide No.799/eq-l- @2013 New Raipur Dated 10.07.2013 and 243/fo-@fu- @pkj@2013 New Raipur Dated 06.07.2013 issued by the Chief Secretary. Govt. of Chhattisgarh. 5. Purchasing Department/end user will ensure to issue the

Purchase Order in accordance with the Store Purchase Rules-2002 (As Amended) vide Clause No.-13

(Subas Chandra Bhagat) Incharge Marketing

Page 44: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

44/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7920 Dt.: 12-04-2017

Annexure-B CSIDC/MKD/TECH/2016-17/28

SPECIFICATION FOR WATER TANKER MOUNTED ON FOUR / TWO WHEEL TROLLEY

TSC 23-11-2016

(E) SPECIFICATION OF PRODUCTS

(A) TANKERS MOUNTED ON FOUR WHEEL TROLLEY (WITH 7.50 X 16 TYRE & TUBE) WITH LEAF SPRING OR WITHOUT LEAF SPRING

1. Chassis:

The Chassis shall be fabricated as per standard practice to mount the MS tank. All the joint shall be welded with gusset plates wherever required as per standard practice.

The Chassis frame shall have two longitudinal member and 5 cross members of channel

section of size 125 x 65 mm (ISMC) for 4500 & 5000 lts. Capacity. For 3500 lts. Capacity the chassis frame shall have two longitudinal members and 4 cross members of channel section of size 100 x 50 mm (ISMC) The overall approximate dimensions of various tanker trolley chassis shall be as under:- -----------------------------------------------------------------------------------------------------

S.No. Approx.Cap Length Width -----------------------------------------------------------------------------------------------------

1. 5000 liters 4 metres 1.00 mtr. 2. 4500 liters 4 meters 1.00 mtr. 3. 3500 liters 3.5 meters 1.00 mtr.

-----------------------------------------------------------------------------------------------------

2. Turn table:

The turn table frame shall be made out of 100x50mm (ISMC) MS channel with cross support, fixed with double rings fabricated from Angle Iron 40x40x6 mm and with 40mm diameter centre pin with suitable washer and locking arrangement.

3. Draw Bar:

Draw bar shall be in triangular construction made out of ISMC of size 100x50 mm with spring loaded eyehook made of 40mm dia MS bar.

The straight length of draw bar should be 150 cms including eye hook. Draw bar shall be hinged with the frame of turn table by 500 x 25mm Ms round bar having locking arrangement at both the end.

4. Axle & Brake assembly:

Axle shall be made from 63 x 63mm square bar with both the end machined, threaded and fitted with hubs and hexagonal lock nut, fitted with twin taper roller bearings, and provided with grease nipples for greasing the moving parts. For braking mechanical-internal expanding type brakes with suitable drums. hand operated, on rear wheels compete, with steel rod, clamps, springs and hand lever be provided.

(S.N. Chopra)

Incharge PS-III

Page 45: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

45/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7920 Dt.: 12-04-2017

5. Leaf Spring:

Four sets of leaf spring consisting of 13 leaves of size minimum 70 x 10mm, 1000mm long (distance between two pin) of alloy steel shall be provided. These leaf spring shall be fixed with frame by means of complete cast iron bracket assembly.

6. Tyres, tubes & wheel Assembly :

Four number tyre of 7.50 x 16 and tubes of standard make, Shall be provided with double plated rims 5mm thick with 5/6 nos. holes.

7. Water tanker:

The Water Tanker shall have capacity of 5000, 4500 & 3500 litres approx., and shall be manufactured in elliptical shape/ semi elliptical shape. The approx size of Water Tanker shall be as follows:- ----------------------------------------------------------------------------------------------------------- S. No. Approx. Major Axis Minor Axis Length ----------------------------------------------------------------------------------------------------------- 1. 5000 lit. 1.95 mtrs. 1.05 mtrs. 3.6 mtrs. 2. 4500 lit. 1.75 mtrs. 1.05 mtrs. 3.6 mtrs. 3. 3500 lit.. 1.5 mtrs 1.05 mtrs. 3.0 mtrs -----------------------------------------------------------------------------------------------------------

The tank shall be made out of 3.15mm thick MS sheet, and end plates of 4.0mm thick MS plate. End plate shall be maximum in two piece.

The tank shall be reinforced from inside by welding four numbers of elliptical rings made of 40 x 40 x 6mm MS angle one at both ends and two in between at suitable distance (total 04 on.) for 4500 & 5000 lts capacity. For 3500 lts capacity angle rings shall be provided at both ends and one at the middle (total 03 no.)

Two nos. baffle plate of 3.15mm thick MS sheet shall be provided in side the tank. These plates shall be properly welded with the central ring as per the standard practice. The height of baffle plate shall be 20cm. More than half of the height of tank. For 3500 lts capacity only one baffle plate be provided.

8. Manhole:

Two manhole with hinged cover shall be provided at the top of the tank. The cover of tank shall be fabricated from 3.15 thick MS sheet. The collar of the cover and manhole shall be made out of 4.00 mm MS strip. Locking arrangement for cover shall be provided; The manhole covers shall be such fabricated so that no foreign material may enter into the tank.

A 300 mm wide five steps ladder made of 32 x 32 x 2.5/3mm Ms angle be provided at left hand on rear side of the tanker (i.e. cleaner seat side). One no. 300 mm wide platform for full length at left hand be provided at appropriate level. The platform frame be made from Angle Iron 32 x 32 x2.5/3mm and 2.5 mm thick MS sheet. A suitable railing of 150 mm height on full length of platform shall be provided at the outer side of the platform by using 25x25x2.5/3mm Angle Iron or 25mm pipe and 2.0 mm MS sheet.

(S.N. Chopra) Incharge PS-III

Page 46: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

46/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7920 Dt.: 12-04-2017

The rear wheels shall be covered with mudguards fabricated out of 1.6mm thick MS sheets,

as per standard practice.

The Water Tanker shall be fixed on the chassis by 8 nos. suitable arranged fabricated shoes (box type brackets) from 5mm thick plates and base plate of approximate size 23x17 cms. and 12mm thick OR made of suitable ISMC bolted to the chassis with suitable ‘U’ clamps (two nos. in each base) The box brackets width shall not be less than 60mm and the bottom of the tank shall be provided with 6 mm thick and 120mm wide saddle plates for full width of the tank as a base for the shoes (box type brackets).

9. Ball Bering No. 31213 must be used. (B) TANKERS MOUNTED ON TWO WHEEL TROLLEY WITH LEAF SPRING OR

WITHOUT LEAF SPRING 1. Chassis:

The Chassis shall be fabricated as per standard practice to mount the MS tank. All the joint shall be welded with gusset plates wherever required as per standard practice.

The Chassis frame shall have two longitudinal member and 4 cross members of channel

section of size 100 x 50 mm (ISMC).

The overall approximate dimensions of various tanker trolley chassis shall be as under:- -----------------------------------------------------------------------------------------------------

S.No. Approx.Cap Length Width -----------------------------------------------------------------------------------------------------

1. 3500 liters 3.0 metres 0.80 mtr. 2. 2500 liters 2.5 meters 0.80 mtr.

----------------------------------------------------------------------------------------------------- 2. Draw bar:

Draw bar shall be in triangular construction made out of MS channel of size 100 x 50 mm with spring loaded eyehook made of 40 mm dia MS bar.

The straight length of draw bar should be 150 cms including eye hook.

3. Axle & Brake assembly:

Axle shall be made from 63 x 63mm square bar with both the end machined and threaded and provided with iron hubs and hexagonal lock nut, fitted with twin taper roller bearings and provided with grease nipples for greasing the moving parts.

4. Leaf spring:

Two sets of leaf spring consisting of 13 leaves of size 70 x 10mm minimum 1000 mm long (distance between two pin) of alloy steel shall be provided. These leaf spring shall be fixed with frame by means of complete cast iron bracket assembly.

5. Tyres, tubes & wheel Assembly:

(S.N. Chopra)

Incharge PS-III

Page 47: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

47/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7920 Dt.: 12-04-2017

Two number tyres of 7.50 x 16 and tubes of standard make shall be provided with double plated rims 5 mm thick with 5/6 nos. holes for 2500 lts. Capacity tanker. For 3500 lts. Capacity two number tyres of 9x16 and tubes of standard make shall be provided.

6. Water Tanker:

The Water Tanker Should have capacity of 2500 & 3500 liters approx. Manufactured in elliptical. Shape. The approx. size of Water Tanker are as follows :-

-------------------------------------------------------------------------------------------------------------- S.No. Approx.Cap Major Axis Minor Axis Length -------------------------------------------------------------------------------------------------------------- 1. 3500 liters 1.5 mtrs 1.05 mtrs 3.0 mtrs. 2. 2500 liters 1.20 mtrs 1.05 mtrs 2.5 mtrs. --------------------------------------------------------------------------------------------------------------

The tank shall be made out of 3.15 mm thick MS sheet, and end plates of 4.0 thick MS plate. End plate should be maximum two pieces.

The tank shall be reinforced from inside by welding three numbers of elliptical rings made of 40 x 40 x 6mm MS angle one at both ends and one in between at suitable distance.

One baffle plate of 3.15mm shall be provided inside the tank. These plates shall be properly welded with the central ring as per the standard practice. The height of baffle plate shall be 20 cm more than half of the height of tank.

7. Manhole:

One manhole with hinged cover shall be provided at the top of the tank. The cover of tank shall be fabricated from 3.15 thick MS sheet. The collar of the cover and manhole shall be made out of 4.00 mm MS strip. Locking arrangement for cover shall also be provided; The manhole cover shall be such fabricated so that no foreign material may enter in to the tank.

A 300 mm wide three steps ladder made of 32x32x2.5/3mm MS angle be provided at left hand on front side of the tanker (i.e. cleaner seat side). One no. 300mm wide platform for full length at left hand be provided at appropriate level. The platform frame be made from angle iron 32x32x2.5/3mm and 2.5 mm thick MS sheet. A suitable railing of 150mm height on full length of platform shall be provided at the outer side of the platform by using 25x25x3mm Angle Iron of 25mm pipe and 2.0mm MS Sheet.

The water tanker shall be fixed on the chassis by 6 nos. suitable arranged fabricated shoes (box type brackets) from 5mm thick plates and base plate of approximate size 23 x 17 cms. and 12 mm thick OR made of suitable ISMC bolted to the chassis with suitable ‘U’ clamps (two nos. in each base). The box brackets width shall not be less than 60 mm and the bottom of the tank shall be provided with 6 mm thick and 120 mm wide saddle plates for full width of the tank as a base for the shoes (box type brackets.)

8. Ball Bering No. 31213 must be used.

(C) TANKERS MOUNTED ON FOUR WHEEL TROLLEY: (WITH 9X20 TYRES TUBES)

1. Chassis: The Chassis shall be fabricated as per standard practice to mount the MS tank. All the joint

shall be welded with gusset plates wherever required as per standard practice.

(S.N. Chopra)

Incharge PS-III

Page 48: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

48/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7920 Dt.: 12-04-2017

The chassis frame shall have two longitudinal member and 3 cross members of channel section of size 150x75mm (ISMC) for 4000 & 5000 It. Capacity.

The width of the chassis frame shall be of 1.0mt and length shall be equal to the length of the tank.

2. Turn table:

The turn table frame shall be made out of 100x50mm (ISMC or equivalent) MS channel with cross support, fixed with double rings fabricated out of Angle Iron 40x40x6 mm and with 40mm diameter centre pin with suitable washer and locking arrangement.

3. Draw Bar:

Draw bar shall be in triangular construction made out of Ms Channel of size 100x50 mm with spring loaded eyehook made of 40mm dia MS bar.

The straight length of draw bar should be 150 cms including eye hook. Draw bar shall be hinged with the frame of turn table by 100x25mm MS round bar having locking arrangement at both the end.

4. Axle & Brake assembly:

Axle shall be made from 63x63mm square bar of 1750mm length with both the end machined and threaded and provided with iron hubs and hexagonal lock nut, fitted with twin taper roller bearings, and provided with grease nipples for greasing the moving parts. For braking mechanical-internal expanding type brakes with suitable drums, hand operated, on rear wheels compete, with steel rod, clamps, springs and hand lever be provided.

5. Leaf Spring:

Four sets of leaf spring consisting of 13 leaves of size 70x11 mm minimum 1000mm long (distance between two pin) of alloy steel shall be provided. These leaf spring shall be fixed with frame by means of complete cast iron bracket assembly.

6. Tyres, tubes & wheel Assembly :

Four number tyre of 9 x 20 and tubes of standard make. Shall be provided with double plated rims 5 mm thick with 5/6 nos. holes. For four wheel trolley.

7. Water tanker:

The Water Tanker shall have capacity of 5000 & 4000 litres approx. manufactured in semi elliptical shape.

The minor axis of the tank shall be of 1.05 mtr. The manufacturer shall design major axis

and length of the semi elliptical tank accordingly. The tank shall be made out of 3.15 mm thick MS sheet, and end plates of 4.0 thick MS plate.

End plate should be maximum two pieces.

(S.N. Chopra)

Incharge PS-III

Page 49: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

49/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7920 Dt.: 12-04-2017

The tank shall be reinforced from inside by welding three numbers of elliptical rings made of 40 x 40 x 6mm MS angle one at both ends and one in between at suitable distance.

Two baffle plate of 3.15mm shall be provided in side the tank. These plates shall be properly

welded with the central ring as per the standard practice. The height of baffle plate shall be 20 cm more than half of the height of tank.

8. Manhole:

Two manhole with hinged cover shall be provided at the top of the tank. The cover of tank shall be fabricated from 3.15 thick MS sheet. The collar of the cover and manhole shall be made out of 4.00 mm MS strip. Locking arrangement for cover shall also be provided; The manhole cover shall be such fabricated so that no foreign material may enter in to the tank.

A 300 mm wide three steps ladder made of 30x30x3mm MS angle be provided at left hand

on front side of the tanker. One no. 300mm wide platform for full length at left hand be provided at appropriate level. The platform frame be made from angle iron 35x35x3mm and 2.5 mm thick MS sheet. A suitable railing of 150mm height on full length of platform shall be provided at the outer side of the platform by using 25x25x3mm Angle Iron of 25mm pipe and 2.0mm MS Sheet.

The water tanker shall be fixed on the chassis by 8 nos. suitable arranged fabricated shoes

(box type brackets) from 5mm thick plates and base plate of approximate size 23 x 17 cms. and 12mm thick bolted to the chassis or made of 100x50mm channel properly covered with sheet of 3.15mm suitable ‘U’ clamps (two nos. in each base). The box brackets width shall not be less than 60 mm and the bottom of the tank shall be provided with 6 mm thick and 120 mm wide saddle plates for full width of the tank as a base for the shoes (box type brackets.)

9. Ball Bering No. –31213 must be used. (D) TANKERS MOUNTED ON TWO WHEEL TROLLEY WITH LEAF SPRING OF

WITHOUT LEAF SPRING: 1. Chassis:

The Chassis shall be fabricated as per standard practice to mount the MS tank. All the joint shall be welded with gusset plates wherever required as per standard practice.

The Chassis frame shall have two longitudinal members and 4 cross members of channel

section of size 150 x 75 mm (ISMC) The overall approximate dimensions of various tanker trolley chassis shall be as under:- -----------------------------------------------------------------------------------------------------

S.No. Approx.Cap Length Width -----------------------------------------------------------------------------------------------------

1. 4000 liters 3.3 metres 1.2 mtr. 2. 4500 liters 3.5 meters 1.2 mtr. 3. 5000 liters 3.5 meters 1.2 mtr. 4. 5500 liters 3.7 metres 1.2 mtr.

-----------------------------------------------------------------------------------------------------

(S.N. Chopra) Incharge PS-III

Page 50: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

50/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7920 Dt.: 12-04-2017 WATER TANKERS MOUNTED ON FOUR/TWO WHEEL TROLLEY 2. Draw Bar:

Draw bar shall be in triangular construction made out of MS channel of size 150x75 mm with spring loaded eyehook made of 40mm dia MS bar.

The minimum straight length of draw bar should be 150 cms including eye hook.

3. Axle & Brake assembly:

Axle shall be made from 72 x 72mm square bar with both the end machined and threaded and provided with iron hubs and hexagonal lock nut, fitted with twin taper roller bearings and provided with grease nipples for greasing the moving parts.

4. Leaf Spring:

Two sets of leaf spring consisting of 13 leaves of 4000 & 4500 Ltr. And 19 leaves for 5000 & 5500 ltr. Cap. Of size minimum 70 x 10mm minimum 900mm long (distance between two pin) of alloy steel shall be provided. These leaf spring shall be fixed with frame by means of complete cast iron bracket assembly.

5. Tyres, tubes & wheel Assembly :

Two number tyre of 9 x16 / 9x16 and tubes of standard make Shall be provided with double plated rims 5mm thick with 8 nos. holes.

6. Water tanker:

The Water Tanker should have capacity of 5000, 5500 litres approx. manufactured in elliptical shape. The approx size of Water Tanker are as follows:- ----------------------------------------------------------------------------------------------------------- S. No. Approx. Major Axis Minor Axis Length ----------------------------------------------------------------------------------------------------------- 1. 4000 lit. 1.65 meters 1.11 mtrs. 2.8 mtrs. 2. 4500 lit. 1.70 meters 1.13 mtrs. 3.0 mtrs. 3. 5000 lit. 1.80 meters 1.18 mtrs. 3.0 mtrs 4. 5500 lit. 1.80 meters 1.22 mtrs. 3.2 mtrs. -----------------------------------------------------------------------------------------------------------

WATER TANKERS MOUNTED ON FOUR/TWO WHEEL TROLLEY

The tank shall be made out of 3.15mm thick MS sheet, and end plates of 4.0mm thick MS plate. End plate should be in maximum two pieces.

The tank shall be reinforced form inside by welding three numbers of elliptical rings made of

40x40x6mm MS Angle one at both ends and one in between at suitable distance.

One baffle plate of 3.15mm shall be provided in side the tank. These plates shall be properly welded with the central ring as per the standard practice. The height of baffle plate shall be 20cm. more than half of the minor axis of tank.

(S.N. Chopra)

Incharge PS-III

Page 51: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

51/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7920 Dt.: 12-04-2017 7. Manhole:

One manhole with hinged cover shall be provided at the top of the tank. The cover of tank shall be fabricated from 3.15 thick MS sheet. The collar of the cover and manhole shall be made out of 4.00 mm MS strip. Locking arrangement for cover shall also be provided; The manhole cover shall be such fabricated so that no foreign material may enter in to the tank.

A 300 mm wide three steps ladder made of 32x32x2.5/3mm MS angle be provided at

left hand on front side of the tanker (i.e. cleaner seat side). One no. 300mm wide platform for full length at left hand be provided at appropriate level. The platform frame be made from angle iron 32x32x2.5/3mm and 2.5 mm thick MS sheet. A suitable railing of 150mm height on full length of platform shall be provided at the outer side of the platform by using 25x25x3mm Angle Iron of 25mm pipe and 2.0mm MS Sheet.

The water tanker shall be fixed on the chassis by 6 nos. suitable arranged fabricated shoes (box type brackets) from 5mm thick plates and base plate of approximate size 23 x 17 cms. and 12 mm thick OR made of suitable ISMC bolted to the chassis with suitable ‘U’ clamps (two nos. in each base). The box brackets width shall not be less than 60 mm and the bottom of the tank shall be provided with 6 mm thick and 120 mm wide saddle plates for full width of the tank as a base for the shoes (box type brackets.)

Pump set stand shall be provided at rear side of the tank.

8. Ball Bering No. 31213 must be used.

WATER TANKERS MOUNTED ON FOUR/TWO WHEEL TROLLEY

1. Outlet:

Outlet 75 mm NB class ‘A’ GI nipple of 10 length (minimum) be provided at the rear of the tank along with required 75 mm GM full way wheel valve, followed by another 20 cm length nipple for connecting a hose pipe. A Drain plug of 50 mm shall be provided at the bottom of the tank at suitable place.

2. Accessories:

The water tanker shall be provided with 2 nos. of reflectors, number plate and tool box etc. The size of tool box should be 600 mm (L) x 300 mm (W) x 300 mm (H) made of 2.5 mm MS sheet.

3. Painting & Finishing:

The tanker should be spray painted, with printing coat of red-oxide and two coat of synthetic enamel paint and color as desired by consignee. Interior of the tank should be painted with two coat of suitable primer followed by Non-poisonous white rubber paint.

4. Guarantee:-

The manufacturer shall furnish guarantee for one year against manufacturing defects leakage etc., along with tenders incorporating that in case of complaint they shall undertake satisfactory repairs within 10 days free of cast.

(S.N. Chopra) Incharge PS-III

Page 52: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

52/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7920 Dt.: 12-04-2017

5. Inspection:-

The inspection of water tanker shall be carried out by of CSIDC, Ltd. Approved Inspection Agencies

6. Ball Bering No. 31213 must be used.

Note:- If required minor deviation/amendment in specification may be done, after taking approval from CSIDC, Ltd,.

Recommended by Technical Specification Committee Dated 23-11-2016

(S.N. Chopra)

Incharge PS-III

Page 53: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

53/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7920 Dt.: 12-04-2017

SCHEDULE ‘B’

(SPECIAL CONDITION OF CONTRACT) ISI Pressure Cooker

Rate Contract Will be governed by the Terms & Conditions laid down in the

CSIDC FORM NO. 1 & 2

(Subas Chandra Bhagat) Incharge Marketing

Page 54: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

54/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7920 Dt.: 12-04-2017

SCHEDULE “C” LIST OF PARALLEL RATE CONTRACT FOR ITEM- Water Tanker

(Subas Chandra Bhagat) Incharge Marketing

S.No. Name of Tenderers Valid Up to Rate Contract No.

1. M/s Agrahari Agrotech Industries, Village-Bori, Tah & Dist.- Rajnandgaon Mob-9753072555

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/AAI/7915

2. M/s G.V. Industries, 22 A, Industrial Area, Dhar-454001 (M.P.) Mob-9425046639, 9826469388

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/G.V.I/7916

3. M/s National Engineering Works, Opp. Sirpur Lake Indore Ahmedabad Road, Indore (M.P.), Mob-07000233648

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/NEW/7920

4. M/s Netam Engineering Works, Audhogik Area, Bhakhara Road, Villa-Arjuni, Dhamtari, Mob-9406021763, 8602729134

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/NEW/7921

5. M/s New Malwa Agro & Fabricators, Plot No.-59, Sec-C, Sirgitti, Industrial Area, Bilaspur, Mob-9425046639, 7772086742

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/NMA&F/7922

6. M/s Rahul Enterprises, Office- 1016, Roshan Gagh, Pushpa Nagar Road, Esh Bagh (M.P.) Mob.-9826469388, 9826038441

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/RE/7923

7. M/s Shri Sai Steel Industries, Industrial.Area Nainpur, Surajpur, Distt.-Surajpur (C.G.) -497229 Mob.-9826649514 Email- [email protected]

17-05-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/SSSI/7919

Page 55: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

55/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7920 Dt.: 12-04-2017

SCHEDULE – “D”

FORMAT FOR QUATERLY DRAWAL REPORT Name of the Firm __________________ I- Jan-Mar Report No. __________________ II- Apr-June Rate Contract No. __________________ III- July-Sept. Date of Submission __________________ IV- Oct - Dec Total Position of Order against Rate Contract till the submission of Report. S.No. Name of

Department Quantity and Value of Orders Received (Rs.)

Quantity and Value of Orders Executed (Rs.)

Balance Quantity and Value to be Supplied (Rs.)

Reasons

Foot 1. Value indicate should be a) Value of orders received during the quarter-Rs.

Total value inclusive of all Taxes duties and incidental b) Value of orders supplied during the quarter-Rs. Charges

2. Nil report should also be Submitted.

(Subas Chandra Bhagat) Incharge Marketing

Page 56: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

56/127

Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh Undertaking) 1st Floor Udhyog Bhawan Ring Road No. -1, Telibhanadha Raipur 492006 (C.G) EPABX No.-91771-6002071-73, Tele Fax : 91771-2583793 & 91771- 4057624 (MKT) CIN- U45203CT1981SG001853 PAN – AABCM6288N Service Tax Regn. No- AABCM6288NSD004. Website: www. csidc.in, Email : [email protected], [email protected]

No./CSIDC/MKD/PS-III/16-17/ Raipur, Dated : Registered A/D Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7921 Dt.: 12-04-2017

To, M/s Netam Engineering Works, Audhogik Area, Bhakhara Road, Villa-Arjuni, Dhamtari (C.G.) Mob-9406021763, 8602729134, [email protected] Sub :- Rate Contract for the supply of Water Tanker (Valid From dated 12-04-2017 to 11-04-2018)

Ref :- (I) This Office Tender Enquiry No. CSIDC/MKD/16-17/143/12768

(II) Your Offer acceptance along with undertaking submitted on dated 10-04-2017

Dear Sir,

You are hereby informed that your above referred tender read with subsequent letters mentioned above for the Stores specified in the Schedules annexed has been accepted. This Rate Contract will be governed by the terms and conditions brought in CSIDC Form No.1 & 2. The Rate Contract and the Schedules annexed hereto shall be the sole repository of this Rate Contract / Transaction. You are required to show the original INK-SIGNED subject Rate Contract to the satisfaction of Direct Demanding Officer who will place the supply order as per instructions contained in CSIDC form No. 2 and also to the Quality Assurance Officer for inspection purpose and to the Paying Authority at the time of getting the payment .

Conditions to be fulfilled by the Purchaser Department (DDO’s) for purchase of store from the Rate Contract holders and Quality Assurance Officer for Inspection of store before delivery :-

It is sole responsibility of the Purchase Department’s (DDO’s) and Quality Assurance Officer to comply with the following conditions as a pre-requisite before accepting delivery/conducting Inspections – (1) Purchase Department’s (DDO’s) shall ensure the validity of following documents applicable for the

Rate Contract Holder to his satisfactions :- A. UAM, Valid Operational Certificate and Competency Certificate. B. PAN Card No., Sales Tax/VAT Tax Registration (TIN).

(2) The above set of documents (As applicable) are required to be inspected by the Quality Assurance Officer before conduction inspection of store.

(3) In case, on the date of delivery OR Inspection, if any of document as mentioned above are not valid OR the validity period of which has been expired. no inspection would be conducted and also no delivery of store to be received from the Rate Contract Holder.

Incharge Marketing

Page 57: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

57/127 (4) Purchase Department’s (DDO’s)/Quality Assurance Officer would be responsible for the any

consequence which may arise due to non compliance of the above conditions and shall keep CSIDC indemnified of any such consequence.

SCHEDULES ANNEXED: 1. Schedule “A” Description of Stores, Prices, Duties / Taxes. 2. Annexure -“B” Technical Particulars of Item Water Tanker. 3. Schedule “B” Special conditions of contract (if any). 4. Schedule “C” Information to DDOs about parallel rate contracts. 5. Schedule “D” Format for Drawal Report.

Total- 18 Pages. Yours faithfully,

(Subas Chandra Bhagat) Incharge Marketing

For and on behalf of the purchaser named in CSIDC Form No.2

Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7921 Dt.: 12-04-2017 +

Copy to :-

1. The Secretary, Chhattisgarh Vidhan Sabha, Raipur.

2. The Registrar, Honourable High court Chhattisgarh, Bilaspur.

3. The Accountant General Chhattisgarh State, Raipur.

4. All HODs of Chhattisgarh Govt.

5. All The Collectors, Chhattisgarh Govt.

6. The Director Treasury, Chhattisgarh Govt. with a request to circulate the copy of Rate Contract to all Direct Demanding Officers of your

institution against issue of purchase order (Indent) in favor of Rate Contract Holders of CSIDC,

7. (i) The Director Education Department (DPI) Indrawati Bhawan, Naya Raipur (C.G.) (ii) The Commissioner Tribal Welfare Department Indrawati Bhawan, Naya Raipur (C.G.) (iii) The Commissioner Directorate of Women & Child Development Indrawati Bhawan, Naya Raipur (C.G.) (iv) Principle Chief Conservator of Forest C.G. Raipur.

8. (i) CSIDC (DEPARTMENTAL TECHNICAL WING) (ii) ADG (Q & A) , DGS&D, Jeewan Tara Building 5 Parliament Street New Delhi 110001 (iii) Manager (Operation) Indian Register of Shipping, Senior MIG-2, Secter A, 1st Floor, Infront

of Bank of India Indrapuri Bhopal. (iv) Chief Engineer, PDIL, 4th floor, 4/2 Karaya Road, 67 Shekespeare Sarani, Kolkata (W.B.) (v) General Manager (Inspection) RITES Ltd., Churchgate Station Road, Second Floor, M.K.

Road, Mumbai-400020 (vi) Operations Manager SGS India Pvt, Ltd. 43, RR Arcade, Zone-2, MP Nagar, Bhopal (MP)-

462011.

9. Manager (Tender), Marketing Div., CSIDC Ltd., Raipur. He is requested to maintain a master file of Rate Contract.

10. Computer cell, CSIDC Ltd., Raipur to release Rate Contract on CSIDC website.

11. Main file of Item- “Water Tanker.”

Incharge Marketing

For and on behalf of the purchaser named in CSIDC Form No.2

Page 58: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

58/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7921 Dt.: 12-04-2017

SCHEDULE “A” Description of Stores, Prices, Duties/Taxes

For the supply of Item- Water Tanker as per Annexure’A’ enclosed.

1. (a) NAME AND FULL ADDRESS OF :- M/s Netam Engineering Works, THE FIRM Audhogik Area, Bhakhara Road,

Villa-Arjuni, Dhamtari (C.G.) Mob-9406021763, 8602729134 [email protected]

(b) NAME AND FULL ADDRESS OF :- M/s Netam Engineering Works, MANUFACTURER Audhogik Area, Bhakhara Road,

Villa-Arjuni, Dhamtari (C.G.)

(c) Catagery :- GEN

2. VALIDITY OF RATE CONTRACT :- From 12-04-2017 to 11-04-2018

3. DESCRIPTION OF ITEM- Water Tanker.

Item Code No.

Item Description Class Rate ( ) F.O.R. Destination

ED NA & VAT Extra if Applicable

Rate Per Unit 1 2 3

WT001 (A) Tankers Mounted On Four Wheel Trolley (With 7.50 X 16 Tyre & Tube) With Leaf Spring 5000 Liters

127139.00

WT002 4500 liters 123143.00 WT004 (A) Tankers Mounted On Four Wheel Trolley (With 7.50 X 16 Tyre &

Tube) Without Leaf Spring 5000 Liters 119060.00

WT005 4500 liters 115871.00 WT006 3500 liters 102104.00 WT007 (B) Tankers Mounted On Two Wheel Trolley With Leaf Spring 3500 Liters 90889.00 WT008 2500 Liters 80259.00 WT009 (B) Tankers Mounted On Two Wheel Trolley Without Leaf Spring 3500

Liters 88763.00

WT010 2500 Liters 73677.00 WT011 (C) Tankers Mounted On Four Wheel Trolley: (With 9x20 Tyres Tubes)

4000 Liters 122249.00

WT012 5000 Liters 127669.00 WT013 (D) Tankers Mounted On Two Wheel Trolley With Leaf Spring 4000 Liters 104178.00 WT014 4500 liters 110413.00 WT015 5000 Liters 117785.00 WT016 5500 Liters 123109.00 WT017 (D) Tankers Mounted On Two Wheel Trolley Without Leaf Spring: 4000

Liters 100457.00

WT018 4500 liters 106303.00 WT019 5000 Liters 114755.00 WT020 5500 Liters 120123.00

Note :- Technical particulars as per Annexure B enclosed

(Subas Chandra Bhagat)

Incharge Marketing

Page 59: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

59/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7921 Dt.: 12-04-2017 4. TERMS OF DELIVERY : F. O. R Destination (Any where in C.G. State)

5. EXCISE DUTY : Not Applicable

6. SALES TAX /VAT : Extra, if applicable

TIN No. 22832104846 Address:-

M/s Netam Engineering Works, Audhogik Area, Bhakhara Road, Villa-Arjuni, Dhamtari (C.G.)

7. DELIVERY PERIOD : 45 Days

8. a. ANNUAL TURN OVER/ : NM

b. MONETARY LIMIT : NM

c. INSTALLED CAPACITY : (As per UAM Certificate)

Water Tanker

Description Annual Capacity

Water Tanker 10 Nos.

9. SLAB DISCOUNT (IF ANY) : Nil 10. PRICES : Prices are Firm and Final 11. MINIMUM QUANTITY IN : Not Mentioned. SINGLE SUPPLY ORDER 12. STATUS OF RC HOLDING : Manufacturer

FIRM 13. REGISTRATION STATUS : Manufacturer is Registered with MSME-UAM UAN- CG04A0000376 14 BIS LICENSE : Not Applicable 15. PAYING AUTHORITY : As Mentioned in supply order to be issued by Direct Demanding Officers (DDOs).

16. PAYMENT TERMS : The payment of full 100% of prices of the stores of each consignment there-of will be made after receipt and acceptance of the stores by the consignee/interim consignee in full and good condition within 20 days as per SPR rule No.11, if the bills are in order. In case of delay in payment without any reason the department will be liable to pay interest as per prevailing bank rate. Bills are to be submitted in the prescribed form of the paying authority of purchaser / indenter and are to be supported with inspection note issued by the inspector and consignee’s Receipt Certificate.

(Subas Chandra Bhagat)

Incharge Marketing

Page 60: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

60/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7921 Dt.: 12-04-2017

17 INSPECTION AUTHORITY : CSIDC (DEPARTMENTAL TECHNICAL WING) Bhilai OR ADG (Q & A) , DGS&D, Jeewan Tara Building 5 Parliament Street New Delhi 110001 OR Manager (Operation) Indian Register of Shipping Senior MIG-2, Secter A, 1st Floor, in front of Bank of India Indrapuri Bhopal (M.P.)

OR Chief Engineer, Project & Development India Ltd. 4st floor, 4/2 Karaya Road, 67 Shekespeare Sarani Kolkata (W.B.)

OR General Manager (Inspection) RITES Ltd. Churchgate Station Road, Second Floor, M.K. Road, Mumbai- 400020 (Mah) OR

Manager (Operations) SGS India Pvt. Ltd. 43, RR Arcade, Zone-2, MP Nagar, Bhopal-462011. (M.P.)

18 QUALITY ASSURANCE: CSIDC (DEPARTMENTAL TECHNICAL WING) Bhilai

Shri Sanjiv Awasthy Mob. No. 9926999936 Email- [email protected] OR Dy. Director (Q&A), DGS&D, Bhilai (C.G.) DGS&D, Sector 1, Street-10 Old Telegraph Office, Bhilai (C.G), Fax No.- 0788-2223374 OR Manager (Operation) Indian Register of Shipping Senior MIG-2, Secter A, 1st Floor, in front of Bank of India Indrapuri Bhopal. (M.P.) Shri Amit Kumar Gupta Mob. No. 8871453225] M. Nazim Athar Mob. No. 8085182339

E-mail- [email protected] OR

Chief Engineer, Project & Development India Ltd. 4st floor, 4/2 Karaya Road, 67 Shekespeare Sarani Kolkata (W.B.) Fax No. 033-22873274 OR

General Manager (Inspection) RITES Ltd. Rajnish Ahuja Western Region (Inspection) Pho. No 2201- 2523/5573 Direct 2201 7434 Mob. 08600 017717 Fax 022 22084155, 2222016219

E-mail- [email protected], [email protected] OR

Manager (Operations) SGS India Pvt. Ltd. 43, RR Arcade, Zone-2, MP Nagar, Bhopal-462011. (M.P.) Shri Jitendra Raj Mob. No. 9752848321

E-mail- [email protected]

(Subas Chandra Bhagat)

Incharge Marketing

Page 61: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

61/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7921 Dt.: 12-04-2017 19. PLACE WHERE THE STORES At Manufacturer’s Factory at

ARE TO BE OFFERED FOR M/s Netam Engineering Works, INSPECTION Audhogik Area, Bhakhara Road,

Villa-Arjuni, Dhamtari (C.G.)

20 INSPECTION CHARGES : Inspection charges 0.60%+ Service Tax As applicable to be paid extra at the time of inspection to Quality Assurance Officer which will be billed by the unit along with bill of the material and will be reimbursed by the paying authority of DDO.

21. SECURITY DEPOSIT : As per General conditions of contract, CSIDC Form No. 1, Clause 7,the Purchaser/DDOs may require the contractor to furnish a security deposit which shall be made after issue of the acceptance of the supply order within the period specified by the purchaser / DDOs. Such security deposit shall not ordinarily exceed 3% . The security shall be in form of Demand Drafts issued by any of the Scheduled Commercial Banks. No other form of security is to be accepted. The security deposit amount is to be refunded after successful completion of the supply.

22. Special Note 1. Purchasing Departments/end user will ensure to sending the copy of every Purchase order to this office. 2. Purchasing Departments/end user will ensure to Pre Dispatch inspection of stores through Inspection agency enlisted in the CSIDC Panel. 3. Purchasing Departments/end user will be responsible for ensuring the Quality of accepted stores. As per the Tech. Specification. 4. Purchasing Department/end user shall be ensure to execute the Integrity Pact between BUYER and BIDDER/ SUPPLIER in accordance with the letter vide No.799/eq-l- @2013 New Raipur Dated 10.07.2013 and 243/fo-@fu- @pkj@2013 New Raipur Dated 06.07.2013 issued by the Chief Secretary. Govt. of Chhattisgarh. 5. Purchasing Department/end user will ensure to issue the

Purchase Order in accordance with the Store Purchase Rules-2002 (As Amended) vide Clause No.-13

(Subas Chandra Bhagat) Incharge Marketing

Page 62: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

62/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7921 Dt.: 12-04-2017

Annexure-B CSIDC/MKD/TECH/2016-17/28

SPECIFICATION FOR WATER TANKER MOUNTED ON FOUR / TWO WHEEL TROLLEY

TSC 23-11-2016

(E) SPECIFICATION OF PRODUCTS

(A) TANKERS MOUNTED ON FOUR WHEEL TROLLEY (WITH 7.50 X 16 TYRE & TUBE) WITH LEAF SPRING OR WITHOUT LEAF SPRING

1. Chassis:

The Chassis shall be fabricated as per standard practice to mount the MS tank. All the joint shall be welded with gusset plates wherever required as per standard practice.

The Chassis frame shall have two longitudinal member and 5 cross members of channel

section of size 125 x 65 mm (ISMC) for 4500 & 5000 lts. Capacity. For 3500 lts. Capacity the chassis frame shall have two longitudinal members and 4 cross members of channel section of size 100 x 50 mm (ISMC) The overall approximate dimensions of various tanker trolley chassis shall be as under:- -----------------------------------------------------------------------------------------------------

S.No. Approx.Cap Length Width -----------------------------------------------------------------------------------------------------

1. 5000 liters 4 metres 1.00 mtr. 2. 4500 liters 4 meters 1.00 mtr. 3. 3500 liters 3.5 meters 1.00 mtr.

-----------------------------------------------------------------------------------------------------

2. Turn table:

The turn table frame shall be made out of 100x50mm (ISMC) MS channel with cross support, fixed with double rings fabricated from Angle Iron 40x40x6 mm and with 40mm diameter centre pin with suitable washer and locking arrangement.

3. Draw Bar:

Draw bar shall be in triangular construction made out of ISMC of size 100x50 mm with spring loaded eyehook made of 40mm dia MS bar.

The straight length of draw bar should be 150 cms including eye hook. Draw bar shall be hinged with the frame of turn table by 500 x 25mm Ms round bar having locking arrangement at both the end.

4. Axle & Brake assembly:

Axle shall be made from 63 x 63mm square bar with both the end machined, threaded and fitted with hubs and hexagonal lock nut, fitted with twin taper roller bearings, and provided with grease nipples for greasing the moving parts. For braking mechanical-internal expanding type brakes with suitable drums. hand operated, on rear wheels compete, with steel rod, clamps, springs and hand lever be provided.

(S.N. Chopra)

Incharge PS-III

Page 63: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

63/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7921 Dt.: 12-04-2017

5. Leaf Spring:

Four sets of leaf spring consisting of 13 leaves of size minimum 70 x 10mm, 1000mm long (distance between two pin) of alloy steel shall be provided. These leaf spring shall be fixed with frame by means of complete cast iron bracket assembly.

6. Tyres, tubes & wheel Assembly :

Four number tyre of 7.50 x 16 and tubes of standard make, Shall be provided with double plated rims 5mm thick with 5/6 nos. holes.

7. Water tanker:

The Water Tanker shall have capacity of 5000, 4500 & 3500 litres approx., and shall be manufactured in elliptical shape/ semi elliptical shape. The approx size of Water Tanker shall be as follows:- ----------------------------------------------------------------------------------------------------------- S. No. Approx. Major Axis Minor Axis Length ----------------------------------------------------------------------------------------------------------- 1. 5000 lit. 1.95 mtrs. 1.05 mtrs. 3.6 mtrs. 2. 4500 lit. 1.75 mtrs. 1.05 mtrs. 3.6 mtrs. 3. 3500 lit.. 1.5 mtrs 1.05 mtrs. 3.0 mtrs -----------------------------------------------------------------------------------------------------------

The tank shall be made out of 3.15mm thick MS sheet, and end plates of 4.0mm thick MS plate. End plate shall be maximum in two piece.

The tank shall be reinforced from inside by welding four numbers of elliptical rings made of 40 x 40 x 6mm MS angle one at both ends and two in between at suitable distance (total 04 on.) for 4500 & 5000 lts capacity. For 3500 lts capacity angle rings shall be provided at both ends and one at the middle (total 03 no.)

Two nos. baffle plate of 3.15mm thick MS sheet shall be provided in side the tank. These plates shall be properly welded with the central ring as per the standard practice. The height of baffle plate shall be 20cm. More than half of the height of tank. For 3500 lts capacity only one baffle plate be provided.

8. Manhole:

Two manhole with hinged cover shall be provided at the top of the tank. The cover of tank shall be fabricated from 3.15 thick MS sheet. The collar of the cover and manhole shall be made out of 4.00 mm MS strip. Locking arrangement for cover shall be provided; The manhole covers shall be such fabricated so that no foreign material may enter into the tank.

A 300 mm wide five steps ladder made of 32 x 32 x 2.5/3mm Ms angle be provided at left hand on rear side of the tanker (i.e. cleaner seat side). One no. 300 mm wide platform for full length at left hand be provided at appropriate level. The platform frame be made from Angle Iron 32 x 32 x2.5/3mm and 2.5 mm thick MS sheet. A suitable railing of 150 mm height on full length of platform shall be provided at the outer side of the platform by using 25x25x2.5/3mm Angle Iron or 25mm pipe and 2.0 mm MS sheet.

(S.N. Chopra) Incharge PS-III

Page 64: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

64/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7921 Dt.: 12-04-2017

The rear wheels shall be covered with mudguards fabricated out of 1.6mm thick MS sheets,

as per standard practice.

The Water Tanker shall be fixed on the chassis by 8 nos. suitable arranged fabricated shoes (box type brackets) from 5mm thick plates and base plate of approximate size 23x17 cms. and 12mm thick OR made of suitable ISMC bolted to the chassis with suitable ‘U’ clamps (two nos. in each base) The box brackets width shall not be less than 60mm and the bottom of the tank shall be provided with 6 mm thick and 120mm wide saddle plates for full width of the tank as a base for the shoes (box type brackets).

9. Ball Bering No. 31213 must be used. (B) TANKERS MOUNTED ON TWO WHEEL TROLLEY WITH LEAF SPRING OR

WITHOUT LEAF SPRING 1. Chassis:

The Chassis shall be fabricated as per standard practice to mount the MS tank. All the joint shall be welded with gusset plates wherever required as per standard practice.

The Chassis frame shall have two longitudinal member and 4 cross members of channel

section of size 100 x 50 mm (ISMC).

The overall approximate dimensions of various tanker trolley chassis shall be as under:- -----------------------------------------------------------------------------------------------------

S.No. Approx.Cap Length Width -----------------------------------------------------------------------------------------------------

1. 3500 liters 3.0 metres 0.80 mtr. 2. 2500 liters 2.5 meters 0.80 mtr.

----------------------------------------------------------------------------------------------------- 2. Draw bar:

Draw bar shall be in triangular construction made out of MS channel of size 100 x 50 mm with spring loaded eyehook made of 40 mm dia MS bar.

The straight length of draw bar should be 150 cms including eye hook.

3. Axle & Brake assembly:

Axle shall be made from 63 x 63mm square bar with both the end machined and threaded and provided with iron hubs and hexagonal lock nut, fitted with twin taper roller bearings and provided with grease nipples for greasing the moving parts.

4. Leaf spring:

Two sets of leaf spring consisting of 13 leaves of size 70 x 10mm minimum 1000 mm long (distance between two pin) of alloy steel shall be provided. These leaf spring shall be fixed with frame by means of complete cast iron bracket assembly.

5. Tyres, tubes & wheel Assembly:

(S.N. Chopra)

Incharge PS-III

Page 65: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

65/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7921 Dt.: 12-04-2017

Two number tyres of 7.50 x 16 and tubes of standard make shall be provided with double plated rims 5 mm thick with 5/6 nos. holes for 2500 lts. Capacity tanker. For 3500 lts. Capacity two number tyres of 9x16 and tubes of standard make shall be provided.

6. Water Tanker:

The Water Tanker Should have capacity of 2500 & 3500 liters approx. Manufactured in elliptical. Shape. The approx. size of Water Tanker are as follows :-

-------------------------------------------------------------------------------------------------------------- S.No. Approx.Cap Major Axis Minor Axis Length -------------------------------------------------------------------------------------------------------------- 1. 3500 liters 1.5 mtrs 1.05 mtrs 3.0 mtrs. 2. 2500 liters 1.20 mtrs 1.05 mtrs 2.5 mtrs. --------------------------------------------------------------------------------------------------------------

The tank shall be made out of 3.15 mm thick MS sheet, and end plates of 4.0 thick MS plate. End plate should be maximum two pieces.

The tank shall be reinforced from inside by welding three numbers of elliptical rings made of 40 x 40 x 6mm MS angle one at both ends and one in between at suitable distance.

One baffle plate of 3.15mm shall be provided inside the tank. These plates shall be properly welded with the central ring as per the standard practice. The height of baffle plate shall be 20 cm more than half of the height of tank.

7. Manhole:

One manhole with hinged cover shall be provided at the top of the tank. The cover of tank shall be fabricated from 3.15 thick MS sheet. The collar of the cover and manhole shall be made out of 4.00 mm MS strip. Locking arrangement for cover shall also be provided; The manhole cover shall be such fabricated so that no foreign material may enter in to the tank.

A 300 mm wide three steps ladder made of 32x32x2.5/3mm MS angle be provided at left hand on front side of the tanker (i.e. cleaner seat side). One no. 300mm wide platform for full length at left hand be provided at appropriate level. The platform frame be made from angle iron 32x32x2.5/3mm and 2.5 mm thick MS sheet. A suitable railing of 150mm height on full length of platform shall be provided at the outer side of the platform by using 25x25x3mm Angle Iron of 25mm pipe and 2.0mm MS Sheet.

The water tanker shall be fixed on the chassis by 6 nos. suitable arranged fabricated shoes (box type brackets) from 5mm thick plates and base plate of approximate size 23 x 17 cms. and 12 mm thick OR made of suitable ISMC bolted to the chassis with suitable ‘U’ clamps (two nos. in each base). The box brackets width shall not be less than 60 mm and the bottom of the tank shall be provided with 6 mm thick and 120 mm wide saddle plates for full width of the tank as a base for the shoes (box type brackets.)

8. Ball Bering No. 31213 must be used.

(C) TANKERS MOUNTED ON FOUR WHEEL TROLLEY: (WITH 9X20 TYRES TUBES)

1. Chassis: The Chassis shall be fabricated as per standard practice to mount the MS tank. All the joint

shall be welded with gusset plates wherever required as per standard practice.

(S.N. Chopra)

Incharge PS-III

Page 66: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

66/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7921 Dt.: 12-04-2017

The chassis frame shall have two longitudinal member and 3 cross members of channel section of size 150x75mm (ISMC) for 4000 & 5000 It. Capacity.

The width of the chassis frame shall be of 1.0mt and length shall be equal to the length of the tank.

2. Turn table:

The turn table frame shall be made out of 100x50mm (ISMC or equivalent) MS channel with cross support, fixed with double rings fabricated out of Angle Iron 40x40x6 mm and with 40mm diameter centre pin with suitable washer and locking arrangement.

3. Draw Bar:

Draw bar shall be in triangular construction made out of Ms Channel of size 100x50 mm with spring loaded eyehook made of 40mm dia MS bar.

The straight length of draw bar should be 150 cms including eye hook. Draw bar shall be hinged with the frame of turn table by 100x25mm MS round bar having locking arrangement at both the end.

4. Axle & Brake assembly:

Axle shall be made from 63x63mm square bar of 1750mm length with both the end machined and threaded and provided with iron hubs and hexagonal lock nut, fitted with twin taper roller bearings, and provided with grease nipples for greasing the moving parts. For braking mechanical-internal expanding type brakes with suitable drums, hand operated, on rear wheels compete, with steel rod, clamps, springs and hand lever be provided.

5. Leaf Spring:

Four sets of leaf spring consisting of 13 leaves of size 70x11 mm minimum 1000mm long (distance between two pin) of alloy steel shall be provided. These leaf spring shall be fixed with frame by means of complete cast iron bracket assembly.

6. Tyres, tubes & wheel Assembly :

Four number tyre of 9 x 20 and tubes of standard make. Shall be provided with double plated rims 5 mm thick with 5/6 nos. holes. For four wheel trolley.

7. Water tanker:

The Water Tanker shall have capacity of 5000 & 4000 litres approx. manufactured in semi elliptical shape.

The minor axis of the tank shall be of 1.05 mtr. The manufacturer shall design major axis

and length of the semi elliptical tank accordingly. The tank shall be made out of 3.15 mm thick MS sheet, and end plates of 4.0 thick MS plate.

End plate should be maximum two pieces.

(S.N. Chopra)

Incharge PS-III

Page 67: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

67/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7921 Dt.: 12-04-2017

The tank shall be reinforced from inside by welding three numbers of elliptical rings made of 40 x 40 x 6mm MS angle one at both ends and one in between at suitable distance.

Two baffle plate of 3.15mm shall be provided in side the tank. These plates shall be properly

welded with the central ring as per the standard practice. The height of baffle plate shall be 20 cm more than half of the height of tank.

8. Manhole:

Two manhole with hinged cover shall be provided at the top of the tank. The cover of tank shall be fabricated from 3.15 thick MS sheet. The collar of the cover and manhole shall be made out of 4.00 mm MS strip. Locking arrangement for cover shall also be provided; The manhole cover shall be such fabricated so that no foreign material may enter in to the tank.

A 300 mm wide three steps ladder made of 30x30x3mm MS angle be provided at left hand

on front side of the tanker. One no. 300mm wide platform for full length at left hand be provided at appropriate level. The platform frame be made from angle iron 35x35x3mm and 2.5 mm thick MS sheet. A suitable railing of 150mm height on full length of platform shall be provided at the outer side of the platform by using 25x25x3mm Angle Iron of 25mm pipe and 2.0mm MS Sheet.

The water tanker shall be fixed on the chassis by 8 nos. suitable arranged fabricated shoes

(box type brackets) from 5mm thick plates and base plate of approximate size 23 x 17 cms. and 12mm thick bolted to the chassis or made of 100x50mm channel properly covered with sheet of 3.15mm suitable ‘U’ clamps (two nos. in each base). The box brackets width shall not be less than 60 mm and the bottom of the tank shall be provided with 6 mm thick and 120 mm wide saddle plates for full width of the tank as a base for the shoes (box type brackets.)

9. Ball Bering No. –31213 must be used. (D) TANKERS MOUNTED ON TWO WHEEL TROLLEY WITH LEAF SPRING OF

WITHOUT LEAF SPRING: 1. Chassis:

The Chassis shall be fabricated as per standard practice to mount the MS tank. All the joint shall be welded with gusset plates wherever required as per standard practice.

The Chassis frame shall have two longitudinal members and 4 cross members of channel

section of size 150 x 75 mm (ISMC) The overall approximate dimensions of various tanker trolley chassis shall be as under:- -----------------------------------------------------------------------------------------------------

S.No. Approx.Cap Length Width -----------------------------------------------------------------------------------------------------

1. 4000 liters 3.3 metres 1.2 mtr. 2. 4500 liters 3.5 meters 1.2 mtr. 3. 5000 liters 3.5 meters 1.2 mtr. 4. 5500 liters 3.7 metres 1.2 mtr.

-----------------------------------------------------------------------------------------------------

(S.N. Chopra) Incharge PS-III

Page 68: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

68/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7921 Dt.: 12-04-2017 WATER TANKERS MOUNTED ON FOUR/TWO WHEEL TROLLEY 2. Draw Bar:

Draw bar shall be in triangular construction made out of MS channel of size 150x75 mm with spring loaded eyehook made of 40mm dia MS bar.

The minimum straight length of draw bar should be 150 cms including eye hook.

3. Axle & Brake assembly:

Axle shall be made from 72 x 72mm square bar with both the end machined and threaded and provided with iron hubs and hexagonal lock nut, fitted with twin taper roller bearings and provided with grease nipples for greasing the moving parts.

4. Leaf Spring:

Two sets of leaf spring consisting of 13 leaves of 4000 & 4500 Ltr. And 19 leaves for 5000 & 5500 ltr. Cap. Of size minimum 70 x 10mm minimum 900mm long (distance between two pin) of alloy steel shall be provided. These leaf spring shall be fixed with frame by means of complete cast iron bracket assembly.

5. Tyres, tubes & wheel Assembly :

Two number tyre of 9 x16 / 9x16 and tubes of standard make Shall be provided with double plated rims 5mm thick with 8 nos. holes.

6. Water tanker:

The Water Tanker should have capacity of 5000, 5500 litres approx. manufactured in elliptical shape. The approx size of Water Tanker are as follows:- ----------------------------------------------------------------------------------------------------------- S. No. Approx. Major Axis Minor Axis Length ----------------------------------------------------------------------------------------------------------- 1. 4000 lit. 1.65 meters 1.11 mtrs. 2.8 mtrs. 2. 4500 lit. 1.70 meters 1.13 mtrs. 3.0 mtrs. 3. 5000 lit. 1.80 meters 1.18 mtrs. 3.0 mtrs 4. 5500 lit. 1.80 meters 1.22 mtrs. 3.2 mtrs. -----------------------------------------------------------------------------------------------------------

WATER TANKERS MOUNTED ON FOUR/TWO WHEEL TROLLEY

The tank shall be made out of 3.15mm thick MS sheet, and end plates of 4.0mm thick MS plate. End plate should be in maximum two pieces.

The tank shall be reinforced form inside by welding three numbers of elliptical rings made of

40x40x6mm MS Angle one at both ends and one in between at suitable distance.

One baffle plate of 3.15mm shall be provided in side the tank. These plates shall be properly welded with the central ring as per the standard practice. The height of baffle plate shall be 20cm. more than half of the minor axis of tank.

(S.N. Chopra)

Incharge PS-III

Page 69: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

69/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7921 Dt.: 12-04-2017 7. Manhole:

One manhole with hinged cover shall be provided at the top of the tank. The cover of tank shall be fabricated from 3.15 thick MS sheet. The collar of the cover and manhole shall be made out of 4.00 mm MS strip. Locking arrangement for cover shall also be provided; The manhole cover shall be such fabricated so that no foreign material may enter in to the tank.

A 300 mm wide three steps ladder made of 32x32x2.5/3mm MS angle be provided at

left hand on front side of the tanker (i.e. cleaner seat side). One no. 300mm wide platform for full length at left hand be provided at appropriate level. The platform frame be made from angle iron 32x32x2.5/3mm and 2.5 mm thick MS sheet. A suitable railing of 150mm height on full length of platform shall be provided at the outer side of the platform by using 25x25x3mm Angle Iron of 25mm pipe and 2.0mm MS Sheet.

The water tanker shall be fixed on the chassis by 6 nos. suitable arranged fabricated shoes (box type brackets) from 5mm thick plates and base plate of approximate size 23 x 17 cms. and 12 mm thick OR made of suitable ISMC bolted to the chassis with suitable ‘U’ clamps (two nos. in each base). The box brackets width shall not be less than 60 mm and the bottom of the tank shall be provided with 6 mm thick and 120 mm wide saddle plates for full width of the tank as a base for the shoes (box type brackets.)

Pump set stand shall be provided at rear side of the tank.

8. Ball Bering No. 31213 must be used.

WATER TANKERS MOUNTED ON FOUR/TWO WHEEL TROLLEY

1. Outlet:

Outlet 75 mm NB class ‘A’ GI nipple of 10 length (minimum) be provided at the rear of the tank along with required 75 mm GM full way wheel valve, followed by another 20 cm length nipple for connecting a hose pipe. A Drain plug of 50 mm shall be provided at the bottom of the tank at suitable place.

2. Accessories:

The water tanker shall be provided with 2 nos. of reflectors, number plate and tool box etc. The size of tool box should be 600 mm (L) x 300 mm (W) x 300 mm (H) made of 2.5 mm MS sheet.

3. Painting & Finishing:

The tanker should be spray painted, with printing coat of red-oxide and two coat of synthetic enamel paint and color as desired by consignee. Interior of the tank should be painted with two coat of suitable primer followed by Non-poisonous white rubber paint.

4. Guarantee:-

The manufacturer shall furnish guarantee for one year against manufacturing defects leakage etc., along with tenders incorporating that in case of complaint they shall undertake satisfactory repairs within 10 days free of cast.

(S.N. Chopra) Incharge PS-III

Page 70: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

70/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7921 Dt.: 12-04-2017

5. Inspection:-

The inspection of water tanker shall be carried out by of CSIDC, Ltd. Approved Inspection Agencies

6. Ball Bering No. 31213 must be used.

Note:- If required minor deviation/amendment in specification may be done, after taking approval from CSIDC, Ltd,.

Recommended by Technical Specification Committee Dated 23-11-2016

(S.N. Chopra)

Incharge PS-III

Page 71: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

71/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7921 Dt.: 12-04-2017

SCHEDULE ‘B’

(SPECIAL CONDITION OF CONTRACT) ISI Pressure Cooker

Rate Contract Will be governed by the Terms & Conditions laid down in the

CSIDC FORM NO. 1 & 2

(Subas Chandra Bhagat) Incharge Marketing

Page 72: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

72/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7921 Dt.: 12-04-2017

SCHEDULE “C” LIST OF PARALLEL RATE CONTRACT FOR ITEM- Water Tanker

(Subas Chandra Bhagat) Incharge Marketing

S.No. Name of Tenderers Valid Up to Rate Contract No.

1. M/s Agrahari Agrotech Industries, Village-Bori, Tah & Dist.- Rajnandgaon Mob-9753072555

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/AAI/7915

2. M/s G.V. Industries, 22 A, Industrial Area, Dhar-454001 (M.P.) Mob-9425046639, 9826469388

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/G.V.I/7916

3. M/s National Engineering Works, Opp. Sirpur Lake Indore Ahmedabad Road, Indore (M.P.), Mob-07000233648

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/NEW/7920

4. M/s Netam Engineering Works, Audhogik Area, Bhakhara Road, Villa-Arjuni, Dhamtari, Mob-9406021763, 8602729134

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/NEW/7921

5. M/s New Malwa Agro & Fabricators, Plot No.-59, Sec-C, Sirgitti, Industrial Area, Bilaspur, Mob-9425046639, 7772086742

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/NMA&F/7922

6. M/s Rahul Enterprises, Office- 1016, Roshan Gagh, Pushpa Nagar Road, Esh Bagh (M.P.) Mob.-9826469388, 9826038441

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/RE/7923

7. M/s Shri Sai Steel Industries, Industrial.Area Nainpur, Surajpur, Distt.-Surajpur (C.G.) -497229 Mob.-9826649514 Email- [email protected]

17-05-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/SSSI/7919

Page 73: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

73/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NEW/7921 Dt.: 12-04-2017

SCHEDULE – “D”

FORMAT FOR QUATERLY DRAWAL REPORT Name of the Firm __________________ I- Jan-Mar Report No. __________________ II- Apr-June Rate Contract No. __________________ III- July-Sept. Date of Submission __________________ IV- Oct - Dec Total Position of Order against Rate Contract till the submission of Report. S.No. Name of

Department Quantity and Value of Orders Received (Rs.)

Quantity and Value of Orders Executed (Rs.)

Balance Quantity and Value to be Supplied (Rs.)

Reasons

Foot 1. Value indicate should be a) Value of orders received during the quarter-Rs.

Total value inclusive of all Taxes duties and incidental b) Value of orders supplied during the quarter-Rs. Charges

2. Nil report should also be Submitted.

(Subas Chandra Bhagat) Incharge Marketing

Page 74: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

74/127

Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh Undertaking) 1st Floor Udhyog Bhawan Ring Road No. -1, Telibhanadha Raipur 492006 (C.G) EPABX No.-91771-6002071-73, Tele Fax : 91771-2583793 & 91771- 4057624 (MKT) CIN- U45203CT1981SG001853 PAN – AABCM6288N Service Tax Regn. No- AABCM6288NSD004. Website: www. csidc.in, Email : [email protected], [email protected]

No./CSIDC/MKD/PS-III/16-17/ Raipur, Dated : Registered A/D Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NMA&F/7922 Dt.: 12-04-2017

To, M/s New Malwa Agro & Fabricators, Plot No.-59, Sec-C, Sirgitti, Industrial Area, Bilaspur (C.G.)-49500 Mob-9425046639, 7772086742 [email protected] Sub :- Rate Contract for the supply of Water Tanker (Valid From dated 12-04-2017 to 11-04-2018)

Ref :- (I) This Office Tender Enquiry No. CSIDC/MKD/16-17/143/12768

(II) Your Offer acceptance along with undertaking submitted on dated 10-04-2016

Dear Sir,

You are hereby informed that your above referred tender read with subsequent letters mentioned above for the Stores specified in the Schedules annexed has been accepted. This Rate Contract will be governed by the terms and conditions brought in CSIDC Form No.1 & 2. The Rate Contract and the Schedules annexed hereto shall be the sole repository of this Rate Contract / Transaction. You are required to show the original INK-SIGNED subject Rate Contract to the satisfaction of Direct Demanding Officer who will place the supply order as per instructions contained in CSIDC form No. 2 and also to the Quality Assurance Officer for inspection purpose and to the Paying Authority at the time of getting the payment .

Conditions to be fulfilled by the Purchaser Department (DDO’s) for purchase of store from the Rate Contract holders and Quality Assurance Officer for Inspection of store before delivery :-

It is sole responsibility of the Purchase Department’s (DDO’s) and Quality Assurance Officer to comply with the following conditions as a pre-requisite before accepting delivery/conducting Inspections – (1) Purchase Department’s (DDO’s) shall ensure the validity of following documents applicable for the

Rate Contract Holder to his satisfactions :- A. Udyog Aadhar Memorandum, Valid Operational Certificate. B. PAN Card No., Sales Tax/VAT Tax Registration (TIN).

(2) The above set of documents (As applicable) are required to be inspected by the Quality Assurance Officer before conduction inspection of store.

(3) In case, on the date of delivery OR Inspection, if any of document as mentioned above are not valid OR the validity period of which has been expired. no inspection would be conducted and also no delivery of store to be received from the Rate Contract Holder.

Incharge Marketing

Page 75: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

75/127 (4) Purchase Department’s (DDO’s)/Quality Assurance Officer would be responsible for the any

consequence which may arise due to non compliance of the above conditions and shall keep CSIDC indemnified of any such consequence.

SCHEDULES ANNEXED: 1. Schedule “A” Description of Stores, Prices, Duties / Taxes. 2. Annexure -“B” Technical Particulars of Item Water Tanker. 3. Schedule “B” Special conditions of contract (if any). 4. Schedule “C” Information to DDOs about parallel rate contracts. 5. Schedule “D” Format for Drawal Report.

Total- 18 Pages. Yours faithfully,

(Subas Chandra Bhagat) Incharge Marketing

For and on behalf of the purchaser named in CSIDC Form No.2

Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NMA&F/7922 Dt.: 12-04-2017 +

Copy to :-

1. The Secretary, Chhattisgarh Vidhan Sabha, Raipur.

2. The Registrar, Honourable High court Chhattisgarh, Bilaspur.

3. The Accountant General Chhattisgarh State, Raipur.

4. All HODs of Chhattisgarh Govt.

5. All The Collectors, Chhattisgarh Govt.

6. The Director Treasury, Chhattisgarh Govt. with a request to circulate the copy of Rate Contract to all Direct Demanding Officers of your

institution against issue of purchase order (Indent) in favor of Rate Contract Holders of CSIDC,

7. (i) The Director Education Department (DPI) Indrawati Bhawan, Naya Raipur (C.G.) (ii) The Commissioner Tribal Welfare Department Indrawati Bhawan, Naya Raipur (C.G.) (iii) The Commissioner Directorate of Women & Child Development Indrawati Bhawan, Naya Raipur (C.G.) (iv) Principle Chief Conservator of Forest C.G. Raipur.

8. (i) CSIDC (DEPARTMENTAL TECHNICAL WING) (ii) ADG (Q & A) , DGS&D, Jeewan Tara Building 5 Parliament Street New Delhi 110001 (iii) Manager (Operation) Indian Register of Shipping, Senior MIG-2, Secter A, 1st Floor, Infront

of Bank of India Indrapuri Bhopal. (iv) Chief Engineer, PDIL, 4th floor, 4/2 Karaya Road, 67 Shekespeare Sarani, Kolkata (W.B.) (v) General Manager (Inspection) RITES Ltd., Churchgate Station Road, Second Floor, M.K.

Road, Mumbai-400020 (vi) Operations Manager SGS India Pvt, Ltd. 43, RR Arcade, Zone-2, MP Nagar, Bhopal (MP)-

462011.

9. Manager (Tender), Marketing Div., CSIDC Ltd., Raipur. He is requested to maintain a master file of Rate Contract.

10. Computer cell, CSIDC Ltd., Raipur to release Rate Contract on CSIDC website.

11. Main file of Item- “Water Tanker.”

Incharge Marketing

For and on behalf of the purchaser named in CSIDC Form No.2

Page 76: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

76/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NMA&F/7922 Dt.: 12-04-2017

SCHEDULE “A” Description of Stores, Prices, Duties/Taxes

For the supply of Item- Water Tanker as per Annexure’A’ enclosed.

1. (a) NAME AND FULL ADDRESS OF :- M/s New Malwa Agro & Fabricators, THE FIRM Plot No.-59, Sec-C, Sirgitti, Industrial Area,

Bilaspur (C.G.)-49500 Mob-9425046639, 7772086742 [email protected]

(b) NAME AND FULL ADDRESS OF :- M/s New Malwa Agro & Fabricators, MANUFACTURER Plot No.-59, Sec-C, Sirgitti, Industrial Area,

Bilaspur (C.G.)-49500

(c) Catagery :- GEN

2. VALIDITY OF RATE CONTRACT :- From 12-04-2017 to 11-04-2018

3. DESCRIPTION OF ITEM- Water Tanker.

Item Code No.

Item Description Class Rate ( ) F.O.R. Destination

ED NA & VAT Extra if Applicable

Rate Per Unit 1 2 3

WT001 (A) Tankers Mounted On Four Wheel Trolley (With 7.50 X 16 Tyre & Tube) With Leaf Spring 5000 Liters

127139.00

WT002 4500 liters 123143.00 WT004 (A) Tankers Mounted On Four Wheel Trolley (With 7.50 X 16 Tyre &

Tube) Without Leaf Spring 5000 Liters 119060.00

WT005 4500 liters 115871.00 WT006 3500 liters 102104.00 WT007 (B) Tankers Mounted On Two Wheel Trolley With Leaf Spring 3500 Liters 90889.00 WT008 2500 Liters 80259.00 WT009 (B) Tankers Mounted On Two Wheel Trolley Without Leaf Spring 3500

Liters 88763.00

WT010 2500 Liters 73677.00 WT011 (C) Tankers Mounted On Four Wheel Trolley: (With 9x20 Tyres Tubes)

4000 Liters 122249.00

WT012 5000 Liters 127669.00 WT013 (D) Tankers Mounted On Two Wheel Trolley With Leaf Spring 4000 Liters 104178.00 WT014 4500 liters 110413.00 WT015 5000 Liters 117785.00 WT016 5500 Liters 123109.00 WT017 (D) Tankers Mounted On Two Wheel Trolley Without Leaf Spring: 4000

Liters 100457.00

WT018 4500 liters 106303.00 WT019 5000 Liters 114755.00 WT020 5500 Liters 120123.00

Note :- Technical particulars as per Annexure B enclosed

(Subas Chandra Bhagat)

Incharge Marketing

Page 77: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

77/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NMA&F/7922 Dt.: 12-04-2017 4. TERMS OF DELIVERY : F. O. R Destination (Any where in C.G. State)

5. EXCISE DUTY : Not Applicable

6. SALES TAX /VAT : Extra, if applicable

TIN No. 22354206825 Address:-

M/s New Malwa Agro & Fabricators, Plot No.-59, Sec-C, Sirgitti, Industrial Area, Bilaspur (C.G.)-49500

7. DELIVERY PERIOD : 45 Days

8. a. ANNUAL TURN OVER/ : NM

b. MONETARY LIMIT : NM

c. INSTALLED CAPACITY : (As per UAM Certificate)

Water Tanker

Description Annual Capacity

Water Tanker 1200 Nos.

9. SLAB DISCOUNT (IF ANY) : Nil 10. PRICES : Prices are Firm and Final 11. MINIMUM QUANTITY IN : Not Mentioned. SINGLE SUPPLY ORDER 12. STATUS OF RC HOLDING : Manufacturer

FIRM 13. REGISTRATION STATUS : Manufacturer is Registered with MSME-UAM UAN- CG02A0000758, Dt. 05-04-2016 14 BIS LICENSE : Not Applicable 15. PAYING AUTHORITY : As Mentioned in supply order to be issued by Direct Demanding Officers (DDOs).

16. PAYMENT TERMS : The payment of full 100% of prices of the stores of each consignment there-of will be made after receipt and acceptance of the stores by the consignee/interim consignee in full and good condition within 20 days as per SPR rule No.11, if the bills are in order. In case of delay in payment without any reason the department will be liable to pay interest as per prevailing bank rate. Bills are to be submitted in the prescribed form of the paying authority of purchaser / indenter and are to be supported with inspection note issued by the inspector and consignee’s Receipt Certificate.

(Subas Chandra Bhagat)

Incharge Marketing

Page 78: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

78/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NMA&F/7922 Dt.: 12-04-2017

17 INSPECTION AUTHORITY : CSIDC (DEPARTMENTAL TECHNICAL WING) Bhilai OR ADG (Q & A) , DGS&D, Jeewan Tara Building 5 Parliament Street New Delhi 110001 OR Manager (Operation) Indian Register of Shipping Senior MIG-2, Secter A, 1st Floor, in front of Bank of India Indrapuri Bhopal (M.P.)

OR Chief Engineer, Project & Development India Ltd. 4st floor, 4/2 Karaya Road, 67 Shekespeare Sarani Kolkata (W.B.)

OR General Manager (Inspection) RITES Ltd. Churchgate Station Road, Second Floor, M.K. Road, Mumbai- 400020 (Mah) OR

Manager (Operations) SGS India Pvt. Ltd. 43, RR Arcade, Zone-2, MP Nagar, Bhopal-462011. (M.P.)

18 QUALITY ASSURANCE: CSIDC (DEPARTMENTAL TECHNICAL WING) Bhilai

Shri Sanjiv Awasthy Mob. No. 9926999936 Email- [email protected] OR Dy. Director (Q&A), DGS&D, Bhilai (C.G.) DGS&D, Sector 1, Street-10 Old Telegraph Office, Bhilai (C.G), Fax No.- 0788-2223374 OR Manager (Operation) Indian Register of Shipping Senior MIG-2, Secter A, 1st Floor, in front of Bank of India Indrapuri Bhopal. (M.P.) Shri Amit Kumar Gupta Mob. No. 8871453225] M. Nazim Athar Mob. No. 8085182339

E-mail- [email protected] OR

Chief Engineer, Project & Development India Ltd. 4st floor, 4/2 Karaya Road, 67 Shekespeare Sarani Kolkata (W.B.) Fax No. 033-22873274 OR

General Manager (Inspection) RITES Ltd. Rajnish Ahuja Western Region (Inspection) Pho. No 2201- 2523/5573 Direct 2201 7434 Mob. 08600 017717 Fax 022 22084155, 2222016219

E-mail- [email protected], [email protected] OR

Manager (Operations) SGS India Pvt. Ltd. 43, RR Arcade, Zone-2, MP Nagar, Bhopal-462011. (M.P.) Shri Jitendra Raj Mob. No. 9752848321

E-mail- [email protected]

(Subas Chandra Bhagat)

Incharge Marketing

Page 79: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

79/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NMA&F/7922 Dt.: 12-04-2017 19. PLACE WHERE THE STORES At Manufacturer’s Factory at

ARE TO BE OFFERED FOR M/s New Malwa Agro & Fabricators, INSPECTION Plot No.-59, Sec-C, Sirgitti, Industrial Area,

Bilaspur (C.G.)-49500

20 INSPECTION CHARGES : Inspection charges 0.60%+ Service Tax As applicable to be paid extra at the time of inspection to Quality Assurance Officer which will be billed by the unit along with bill of the material and will be reimbursed by the paying authority of DDO.

21. SECURITY DEPOSIT : As per General conditions of contract, CSIDC Form No. 1, Clause 7,the Purchaser/DDOs may require the contractor to furnish a security deposit which shall be made after issue of the acceptance of the supply order within the period specified by the purchaser / DDOs. Such security deposit shall not ordinarily exceed 3% . The security shall be in form of Demand Drafts issued by any of the Scheduled Commercial Banks. No other form of security is to be accepted. The security deposit amount is to be refunded after successful completion of the supply.

22. Special Note 1. Purchasing Departments/end user will ensure to sending the copy of every Purchase order to this office. 2. Purchasing Departments/end user will ensure to Pre Dispatch inspection of stores through Inspection agency enlisted in the CSIDC Panel. 3. Purchasing Departments/end user will be responsible for ensuring the Quality of accepted stores. As per the Tech. Specification. 4. Purchasing Department/end user shall be ensure to execute the Integrity Pact between BUYER and BIDDER/ SUPPLIER in accordance with the letter vide No.799/eq-l- @2013 New Raipur Dated 10.07.2013 and 243/fo-@fu- @pkj@2013 New Raipur Dated 06.07.2013 issued by the Chief Secretary. Govt. of Chhattisgarh. 5. Purchasing Department/end user will ensure to issue the Purchase Order in accordance with the Store Purchase Rules-2002 (As Amended) vide Clause No.-13

(Subas Chandra Bhagat) Incharge Marketing

Page 80: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

80/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NMA&F/7922 Dt.: 12-04-2017

Annexure-B CSIDC/MKD/TECH/2016-17/28

SPECIFICATION FOR WATER TANKER MOUNTED ON FOUR / TWO WHEEL TROLLEY

TSC 23-11-2016

(E) SPECIFICATION OF PRODUCTS

(A) TANKERS MOUNTED ON FOUR WHEEL TROLLEY (WITH 7.50 X 16 TYRE & TUBE) WITH LEAF SPRING OR WITHOUT LEAF SPRING

1. Chassis:

The Chassis shall be fabricated as per standard practice to mount the MS tank. All the joint shall be welded with gusset plates wherever required as per standard practice.

The Chassis frame shall have two longitudinal member and 5 cross members of channel

section of size 125 x 65 mm (ISMC) for 4500 & 5000 lts. Capacity. For 3500 lts. Capacity the chassis frame shall have two longitudinal members and 4 cross members of channel section of size 100 x 50 mm (ISMC) The overall approximate dimensions of various tanker trolley chassis shall be as under:- -----------------------------------------------------------------------------------------------------

S.No. Approx.Cap Length Width -----------------------------------------------------------------------------------------------------

1. 5000 liters 4 metres 1.00 mtr. 2. 4500 liters 4 meters 1.00 mtr. 3. 3500 liters 3.5 meters 1.00 mtr.

-----------------------------------------------------------------------------------------------------

2. Turn table:

The turn table frame shall be made out of 100x50mm (ISMC) MS channel with cross support, fixed with double rings fabricated from Angle Iron 40x40x6 mm and with 40mm diameter centre pin with suitable washer and locking arrangement.

3. Draw Bar:

Draw bar shall be in triangular construction made out of ISMC of size 100x50 mm with spring loaded eyehook made of 40mm dia MS bar.

The straight length of draw bar should be 150 cms including eye hook. Draw bar shall be hinged with the frame of turn table by 500 x 25mm Ms round bar having locking arrangement at both the end.

4. Axle & Brake assembly:

Axle shall be made from 63 x 63mm square bar with both the end machined, threaded and fitted with hubs and hexagonal lock nut, fitted with twin taper roller bearings, and provided with grease nipples for greasing the moving parts. For braking mechanical-internal expanding type brakes with suitable drums. hand operated, on rear wheels compete, with steel rod, clamps, springs and hand lever be provided.

(S.N. Chopra)

Incharge PS-III

Page 81: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

81/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NMA&F/7922 Dt.: 12-04-2017

5. Leaf Spring:

Four sets of leaf spring consisting of 13 leaves of size minimum 70 x 10mm, 1000mm long (distance between two pin) of alloy steel shall be provided. These leaf spring shall be fixed with frame by means of complete cast iron bracket assembly.

6. Tyres, tubes & wheel Assembly :

Four number tyre of 7.50 x 16 and tubes of standard make, Shall be provided with double plated rims 5mm thick with 5/6 nos. holes.

7. Water tanker:

The Water Tanker shall have capacity of 5000, 4500 & 3500 litres approx., and shall be manufactured in elliptical shape/ semi elliptical shape. The approx size of Water Tanker shall be as follows:- ----------------------------------------------------------------------------------------------------------- S. No. Approx. Major Axis Minor Axis Length ----------------------------------------------------------------------------------------------------------- 1. 5000 lit. 1.95 mtrs. 1.05 mtrs. 3.6 mtrs. 2. 4500 lit. 1.75 mtrs. 1.05 mtrs. 3.6 mtrs. 3. 3500 lit.. 1.5 mtrs 1.05 mtrs. 3.0 mtrs -----------------------------------------------------------------------------------------------------------

The tank shall be made out of 3.15mm thick MS sheet, and end plates of 4.0mm thick MS plate. End plate shall be maximum in two piece.

The tank shall be reinforced from inside by welding four numbers of elliptical rings made of 40 x 40 x 6mm MS angle one at both ends and two in between at suitable distance (total 04 on.) for 4500 & 5000 lts capacity. For 3500 lts capacity angle rings shall be provided at both ends and one at the middle (total 03 no.)

Two nos. baffle plate of 3.15mm thick MS sheet shall be provided in side the tank. These plates shall be properly welded with the central ring as per the standard practice. The height of baffle plate shall be 20cm. More than half of the height of tank. For 3500 lts capacity only one baffle plate be provided.

8. Manhole:

Two manhole with hinged cover shall be provided at the top of the tank. The cover of tank shall be fabricated from 3.15 thick MS sheet. The collar of the cover and manhole shall be made out of 4.00 mm MS strip. Locking arrangement for cover shall be provided; The manhole covers shall be such fabricated so that no foreign material may enter into the tank.

A 300 mm wide five steps ladder made of 32 x 32 x 2.5/3mm Ms angle be provided at left hand on rear side of the tanker (i.e. cleaner seat side). One no. 300 mm wide platform for full length at left hand be provided at appropriate level. The platform frame be made from Angle Iron 32 x 32 x2.5/3mm and 2.5 mm thick MS sheet. A suitable railing of 150 mm height on full length of platform shall be provided at the outer side of the platform by using 25x25x2.5/3mm Angle Iron or 25mm pipe and 2.0 mm MS sheet.

(S.N. Chopra) Incharge PS-III

Page 82: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

82/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NMA&F/7922 Dt.: 12-04-2017

The rear wheels shall be covered with mudguards fabricated out of 1.6mm thick MS sheets,

as per standard practice.

The Water Tanker shall be fixed on the chassis by 8 nos. suitable arranged fabricated shoes (box type brackets) from 5mm thick plates and base plate of approximate size 23x17 cms. and 12mm thick OR made of suitable ISMC bolted to the chassis with suitable ‘U’ clamps (two nos. in each base) The box brackets width shall not be less than 60mm and the bottom of the tank shall be provided with 6 mm thick and 120mm wide saddle plates for full width of the tank as a base for the shoes (box type brackets).

9. Ball Bering No. 31213 must be used. (B) TANKERS MOUNTED ON TWO WHEEL TROLLEY WITH LEAF SPRING OR

WITHOUT LEAF SPRING 1. Chassis:

The Chassis shall be fabricated as per standard practice to mount the MS tank. All the joint shall be welded with gusset plates wherever required as per standard practice.

The Chassis frame shall have two longitudinal member and 4 cross members of channel

section of size 100 x 50 mm (ISMC).

The overall approximate dimensions of various tanker trolley chassis shall be as under:- -----------------------------------------------------------------------------------------------------

S.No. Approx.Cap Length Width -----------------------------------------------------------------------------------------------------

1. 3500 liters 3.0 metres 0.80 mtr. 2. 2500 liters 2.5 meters 0.80 mtr.

----------------------------------------------------------------------------------------------------- 2. Draw bar:

Draw bar shall be in triangular construction made out of MS channel of size 100 x 50 mm with spring loaded eyehook made of 40 mm dia MS bar.

The straight length of draw bar should be 150 cms including eye hook.

3. Axle & Brake assembly:

Axle shall be made from 63 x 63mm square bar with both the end machined and threaded and provided with iron hubs and hexagonal lock nut, fitted with twin taper roller bearings and provided with grease nipples for greasing the moving parts.

4. Leaf spring:

Two sets of leaf spring consisting of 13 leaves of size 70 x 10mm minimum 1000 mm long (distance between two pin) of alloy steel shall be provided. These leaf spring shall be fixed with frame by means of complete cast iron bracket assembly.

5. Tyres, tubes & wheel Assembly:

(S.N. Chopra)

Incharge PS-III

Page 83: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

83/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NMA&F/7922 Dt.: 12-04-2017

Two number tyres of 7.50 x 16 and tubes of standard make shall be provided with double plated rims 5 mm thick with 5/6 nos. holes for 2500 lts. Capacity tanker. For 3500 lts. Capacity two number tyres of 9x16 and tubes of standard make shall be provided.

6. Water Tanker:

The Water Tanker Should have capacity of 2500 & 3500 liters approx. Manufactured in elliptical. Shape. The approx. size of Water Tanker are as follows :-

-------------------------------------------------------------------------------------------------------------- S.No. Approx.Cap Major Axis Minor Axis Length -------------------------------------------------------------------------------------------------------------- 1. 3500 liters 1.5 mtrs 1.05 mtrs 3.0 mtrs. 2. 2500 liters 1.20 mtrs 1.05 mtrs 2.5 mtrs. --------------------------------------------------------------------------------------------------------------

The tank shall be made out of 3.15 mm thick MS sheet, and end plates of 4.0 thick MS plate. End plate should be maximum two pieces.

The tank shall be reinforced from inside by welding three numbers of elliptical rings made of 40 x 40 x 6mm MS angle one at both ends and one in between at suitable distance.

One baffle plate of 3.15mm shall be provided inside the tank. These plates shall be properly welded with the central ring as per the standard practice. The height of baffle plate shall be 20 cm more than half of the height of tank.

7. Manhole:

One manhole with hinged cover shall be provided at the top of the tank. The cover of tank shall be fabricated from 3.15 thick MS sheet. The collar of the cover and manhole shall be made out of 4.00 mm MS strip. Locking arrangement for cover shall also be provided; The manhole cover shall be such fabricated so that no foreign material may enter in to the tank.

A 300 mm wide three steps ladder made of 32x32x2.5/3mm MS angle be provided at left hand on front side of the tanker (i.e. cleaner seat side). One no. 300mm wide platform for full length at left hand be provided at appropriate level. The platform frame be made from angle iron 32x32x2.5/3mm and 2.5 mm thick MS sheet. A suitable railing of 150mm height on full length of platform shall be provided at the outer side of the platform by using 25x25x3mm Angle Iron of 25mm pipe and 2.0mm MS Sheet.

The water tanker shall be fixed on the chassis by 6 nos. suitable arranged fabricated shoes (box type brackets) from 5mm thick plates and base plate of approximate size 23 x 17 cms. and 12 mm thick OR made of suitable ISMC bolted to the chassis with suitable ‘U’ clamps (two nos. in each base). The box brackets width shall not be less than 60 mm and the bottom of the tank shall be provided with 6 mm thick and 120 mm wide saddle plates for full width of the tank as a base for the shoes (box type brackets.)

8. Ball Bering No. 31213 must be used.

(C) TANKERS MOUNTED ON FOUR WHEEL TROLLEY: (WITH 9X20 TYRES TUBES)

1. Chassis: The Chassis shall be fabricated as per standard practice to mount the MS tank. All the joint

shall be welded with gusset plates wherever required as per standard practice.

(S.N. Chopra)

Incharge PS-III

Page 84: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

84/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NMA&F/7922 Dt.: 12-04-2017

The chassis frame shall have two longitudinal member and 3 cross members of channel section of size 150x75mm (ISMC) for 4000 & 5000 It. Capacity.

The width of the chassis frame shall be of 1.0mt and length shall be equal to the length of the tank.

2. Turn table:

The turn table frame shall be made out of 100x50mm (ISMC or equivalent) MS channel with cross support, fixed with double rings fabricated out of Angle Iron 40x40x6 mm and with 40mm diameter centre pin with suitable washer and locking arrangement.

3. Draw Bar:

Draw bar shall be in triangular construction made out of Ms Channel of size 100x50 mm with spring loaded eyehook made of 40mm dia MS bar.

The straight length of draw bar should be 150 cms including eye hook. Draw bar shall be hinged with the frame of turn table by 100x25mm MS round bar having locking arrangement at both the end.

4. Axle & Brake assembly:

Axle shall be made from 63x63mm square bar of 1750mm length with both the end machined and threaded and provided with iron hubs and hexagonal lock nut, fitted with twin taper roller bearings, and provided with grease nipples for greasing the moving parts. For braking mechanical-internal expanding type brakes with suitable drums, hand operated, on rear wheels compete, with steel rod, clamps, springs and hand lever be provided.

5. Leaf Spring:

Four sets of leaf spring consisting of 13 leaves of size 70x11 mm minimum 1000mm long (distance between two pin) of alloy steel shall be provided. These leaf spring shall be fixed with frame by means of complete cast iron bracket assembly.

6. Tyres, tubes & wheel Assembly :

Four number tyre of 9 x 20 and tubes of standard make. Shall be provided with double plated rims 5 mm thick with 5/6 nos. holes. For four wheel trolley.

7. Water tanker:

The Water Tanker shall have capacity of 5000 & 4000 litres approx. manufactured in semi elliptical shape.

The minor axis of the tank shall be of 1.05 mtr. The manufacturer shall design major axis

and length of the semi elliptical tank accordingly. The tank shall be made out of 3.15 mm thick MS sheet, and end plates of 4.0 thick MS plate.

End plate should be maximum two pieces.

(S.N. Chopra)

Incharge PS-III

Page 85: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

85/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NMA&F/7922 Dt.: 12-04-2017

The tank shall be reinforced from inside by welding three numbers of elliptical rings made of 40 x 40 x 6mm MS angle one at both ends and one in between at suitable distance.

Two baffle plate of 3.15mm shall be provided in side the tank. These plates shall be properly

welded with the central ring as per the standard practice. The height of baffle plate shall be 20 cm more than half of the height of tank.

8. Manhole:

Two manhole with hinged cover shall be provided at the top of the tank. The cover of tank shall be fabricated from 3.15 thick MS sheet. The collar of the cover and manhole shall be made out of 4.00 mm MS strip. Locking arrangement for cover shall also be provided; The manhole cover shall be such fabricated so that no foreign material may enter in to the tank.

A 300 mm wide three steps ladder made of 30x30x3mm MS angle be provided at left hand

on front side of the tanker. One no. 300mm wide platform for full length at left hand be provided at appropriate level. The platform frame be made from angle iron 35x35x3mm and 2.5 mm thick MS sheet. A suitable railing of 150mm height on full length of platform shall be provided at the outer side of the platform by using 25x25x3mm Angle Iron of 25mm pipe and 2.0mm MS Sheet.

The water tanker shall be fixed on the chassis by 8 nos. suitable arranged fabricated shoes

(box type brackets) from 5mm thick plates and base plate of approximate size 23 x 17 cms. and 12mm thick bolted to the chassis or made of 100x50mm channel properly covered with sheet of 3.15mm suitable ‘U’ clamps (two nos. in each base). The box brackets width shall not be less than 60 mm and the bottom of the tank shall be provided with 6 mm thick and 120 mm wide saddle plates for full width of the tank as a base for the shoes (box type brackets.)

9. Ball Bering No. –31213 must be used. (D) TANKERS MOUNTED ON TWO WHEEL TROLLEY WITH LEAF SPRING OF

WITHOUT LEAF SPRING: 1. Chassis:

The Chassis shall be fabricated as per standard practice to mount the MS tank. All the joint shall be welded with gusset plates wherever required as per standard practice.

The Chassis frame shall have two longitudinal members and 4 cross members of channel

section of size 150 x 75 mm (ISMC) The overall approximate dimensions of various tanker trolley chassis shall be as under:- -----------------------------------------------------------------------------------------------------

S.No. Approx.Cap Length Width -----------------------------------------------------------------------------------------------------

1. 4000 liters 3.3 metres 1.2 mtr. 2. 4500 liters 3.5 meters 1.2 mtr. 3. 5000 liters 3.5 meters 1.2 mtr. 4. 5500 liters 3.7 metres 1.2 mtr.

-----------------------------------------------------------------------------------------------------

(S.N. Chopra) Incharge PS-III

Page 86: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

86/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NMA&F/7922 Dt.: 12-04-2017 WATER TANKERS MOUNTED ON FOUR/TWO WHEEL TROLLEY 2. Draw Bar:

Draw bar shall be in triangular construction made out of MS channel of size 150x75 mm with spring loaded eyehook made of 40mm dia MS bar.

The minimum straight length of draw bar should be 150 cms including eye hook.

3. Axle & Brake assembly:

Axle shall be made from 72 x 72mm square bar with both the end machined and threaded and provided with iron hubs and hexagonal lock nut, fitted with twin taper roller bearings and provided with grease nipples for greasing the moving parts.

4. Leaf Spring:

Two sets of leaf spring consisting of 13 leaves of 4000 & 4500 Ltr. And 19 leaves for 5000 & 5500 ltr. Cap. Of size minimum 70 x 10mm minimum 900mm long (distance between two pin) of alloy steel shall be provided. These leaf spring shall be fixed with frame by means of complete cast iron bracket assembly.

5. Tyres, tubes & wheel Assembly :

Two number tyre of 9 x16 / 9x16 and tubes of standard make Shall be provided with double plated rims 5mm thick with 8 nos. holes.

6. Water tanker:

The Water Tanker should have capacity of 5000, 5500 litres approx. manufactured in elliptical shape. The approx size of Water Tanker are as follows:- ----------------------------------------------------------------------------------------------------------- S. No. Approx. Major Axis Minor Axis Length ----------------------------------------------------------------------------------------------------------- 1. 4000 lit. 1.65 meters 1.11 mtrs. 2.8 mtrs. 2. 4500 lit. 1.70 meters 1.13 mtrs. 3.0 mtrs. 3. 5000 lit. 1.80 meters 1.18 mtrs. 3.0 mtrs 4. 5500 lit. 1.80 meters 1.22 mtrs. 3.2 mtrs. -----------------------------------------------------------------------------------------------------------

WATER TANKERS MOUNTED ON FOUR/TWO WHEEL TROLLEY

The tank shall be made out of 3.15mm thick MS sheet, and end plates of 4.0mm thick MS plate. End plate should be in maximum two pieces.

The tank shall be reinforced form inside by welding three numbers of elliptical rings made of

40x40x6mm MS Angle one at both ends and one in between at suitable distance.

One baffle plate of 3.15mm shall be provided in side the tank. These plates shall be properly welded with the central ring as per the standard practice. The height of baffle plate shall be 20cm. more than half of the minor axis of tank.

(S.N. Chopra)

Incharge PS-III

Page 87: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

87/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NMA&F/7922 Dt.: 12-04-2017 7. Manhole:

One manhole with hinged cover shall be provided at the top of the tank. The cover of tank shall be fabricated from 3.15 thick MS sheet. The collar of the cover and manhole shall be made out of 4.00 mm MS strip. Locking arrangement for cover shall also be provided; The manhole cover shall be such fabricated so that no foreign material may enter in to the tank.

A 300 mm wide three steps ladder made of 32x32x2.5/3mm MS angle be provided at

left hand on front side of the tanker (i.e. cleaner seat side). One no. 300mm wide platform for full length at left hand be provided at appropriate level. The platform frame be made from angle iron 32x32x2.5/3mm and 2.5 mm thick MS sheet. A suitable railing of 150mm height on full length of platform shall be provided at the outer side of the platform by using 25x25x3mm Angle Iron of 25mm pipe and 2.0mm MS Sheet.

The water tanker shall be fixed on the chassis by 6 nos. suitable arranged fabricated shoes (box type brackets) from 5mm thick plates and base plate of approximate size 23 x 17 cms. and 12 mm thick OR made of suitable ISMC bolted to the chassis with suitable ‘U’ clamps (two nos. in each base). The box brackets width shall not be less than 60 mm and the bottom of the tank shall be provided with 6 mm thick and 120 mm wide saddle plates for full width of the tank as a base for the shoes (box type brackets.)

Pump set stand shall be provided at rear side of the tank.

8. Ball Bering No. 31213 must be used.

WATER TANKERS MOUNTED ON FOUR/TWO WHEEL TROLLEY

1. Outlet:

Outlet 75 mm NB class ‘A’ GI nipple of 10 length (minimum) be provided at the rear of the tank along with required 75 mm GM full way wheel valve, followed by another 20 cm length nipple for connecting a hose pipe. A Drain plug of 50 mm shall be provided at the bottom of the tank at suitable place.

2. Accessories:

The water tanker shall be provided with 2 nos. of reflectors, number plate and tool box etc. The size of tool box should be 600 mm (L) x 300 mm (W) x 300 mm (H) made of 2.5 mm MS sheet.

3. Painting & Finishing:

The tanker should be spray painted, with printing coat of red-oxide and two coat of synthetic enamel paint and color as desired by consignee. Interior of the tank should be painted with two coat of suitable primer followed by Non-poisonous white rubber paint.

4. Guarantee:-

The manufacturer shall furnish guarantee for one year against manufacturing defects leakage etc., along with tenders incorporating that in case of complaint they shall undertake satisfactory repairs within 10 days free of cast.

(S.N. Chopra) Incharge PS-III

Page 88: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

88/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NMA&F/7922 Dt.: 12-04-2017

5. Inspection:-

The inspection of water tanker shall be carried out by of CSIDC, Ltd. Approved Inspection Agencies

6. Ball Bering No. 31213 must be used.

Note:- If required minor deviation/amendment in specification may be done, after taking approval from CSIDC, Ltd,.

Recommended by Technical Specification Committee Dated 23-11-2016

(S.N. Chopra)

Incharge PS-III

Page 89: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

89/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NMA&F/7922 Dt.: 12-04-2017

SCHEDULE ‘B’

(SPECIAL CONDITION OF CONTRACT) ISI Pressure Cooker

Rate Contract Will be governed by the Terms & Conditions laid down in the

CSIDC FORM NO. 1 & 2

(Subas Chandra Bhagat) Incharge Marketing

Page 90: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

90/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NMA&F/7922 Dt.: 12-04-2017

SCHEDULE “C” LIST OF PARALLEL RATE CONTRACT FOR ITEM- Water Tanker

(Subas Chandra Bhagat) Incharge Marketing

S.No. Name of Tenderers Valid Up to Rate Contract No.

1. M/s Agrahari Agrotech Industries, Village-Bori, Tah & Dist.- Rajnandgaon Mob-9753072555

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/AAI/7915

2. M/s G.V. Industries, 22 A, Industrial Area, Dhar-454001 (M.P.) Mob-9425046639, 9826469388

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/G.V.I/7916

3. M/s National Engineering Works, Opp. Sirpur Lake Indore Ahmedabad Road, Indore (M.P.), Mob-07000233648

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/NEW/7920

4. M/s Netam Engineering Works, Audhogik Area, Bhakhara Road, Villa-Arjuni, Dhamtari, Mob-9406021763, 8602729134

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/NEW/7921

5. M/s New Malwa Agro & Fabricators, Plot No.-59, Sec-C, Sirgitti, Industrial Area, Bilaspur, Mob-9425046639, 7772086742

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/NMA&F/7922

6. M/s Rahul Enterprises, Office- 1016, Roshan Gagh, Pushpa Nagar Road, Esh Bagh (M.P.) Mob.-9826469388, 9826038441

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/RE/7923

7. M/s Shri Sai Steel Industries, Industrial.Area Nainpur, Surajpur, Distt.-Surajpur (C.G.) -497229 Mob.-9826649514 Email- [email protected]

17-05-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/SSSI/7919

Page 91: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

91/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/NMA&F/7922 Dt.: 12-04-2017

SCHEDULE – “D”

FORMAT FOR QUATERLY DRAWAL REPORT Name of the Firm __________________ I- Jan-Mar Report No. __________________ II- Apr-June Rate Contract No. __________________ III- July-Sept. Date of Submission __________________ IV- Oct - Dec Total Position of Order against Rate Contract till the submission of Report. S.No. Name of

Department Quantity and Value of Orders Received (Rs.)

Quantity and Value of Orders Executed (Rs.)

Balance Quantity and Value to be Supplied (Rs.)

Reasons

Foot 1. Value indicate should be a) Value of orders received during the quarter-Rs.

Total value inclusive of all Taxes duties and incidental b) Value of orders supplied during the quarter-Rs. Charges

2. Nil report should also be Submitted.

(Subas Chandra Bhagat) Incharge Marketing

Page 92: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

92/127

Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh Undertaking) 1st Floor Udhyog Bhawan Ring Road No. -1, Telibhanadha Raipur 492006 (C.G) EPABX No.-91771-6002071-73, Tele Fax : 91771-2583793 & 91771- 4057624 (MKT) CIN- U45203CT1981SG001853 PAN – AABCM6288N Service Tax Regn. No- AABCM6288NSD004. Website: www. csidc.in, Email : [email protected], [email protected]

No./CSIDC/MKD/PS-III/16-17/ Raipur, Dated : Registered A/D Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/RE/7923 Dt.: 12-04-2017

To, M/s Rahul Enterprises, Office- 1016, Roshan Gagh, Pushpa Nagar Road, Esh Bagh (M.P.) Mob.-9826469388, 9826038441 [email protected] Sub :- Rate Contract for the supply of Water Tanker (Valid From dated 12-04-2017 to 11-04-2018)

Ref :- (I) This Office Tender Enquiry No. CSIDC/MKD/16-17/143/12768

(II) Your Offer acceptance along with undertaking submitted on dated 10-04-2017

Dear Sir,

You are hereby informed that your above referred tender read with subsequent letters mentioned above for the Stores specified in the Schedules annexed has been accepted. This Rate Contract will be governed by the terms and conditions brought in CSIDC Form No.1 & 2. The Rate Contract and the Schedules annexed hereto shall be the sole repository of this Rate Contract / Transaction. You are required to show the original INK-SIGNED subject Rate Contract to the satisfaction of Direct Demanding Officer who will place the supply order as per instructions contained in CSIDC form No. 2 and also to the Quality Assurance Officer for inspection purpose and to the Paying Authority at the time of getting the payment .

Conditions to be fulfilled by the Purchaser Department (DDO’s) for purchase of store from the Rate Contract holders and Quality Assurance Officer for Inspection of store before delivery :-

It is sole responsibility of the Purchase Department’s (DDO’s) and Quality Assurance Officer to comply with the following conditions as a pre-requisite before accepting delivery/conducting Inspections – (1) Purchase Department’s (DDO’s) shall ensure the validity of following documents applicable for the

Rate Contract Holder to his satisfactions :- A. NSIC Registration Certificate, Valid Operational Certificate and Competency Certificate. B. PAN Card No., Sales Tax/VAT Tax Registration (TIN).

(2) The above set of documents (As applicable) are required to be inspected by the Quality Assurance Officer before conduction inspection of store.

(3) In case, on the date of delivery OR Inspection, if any of document as mentioned above are not valid OR the validity period of which has been expired. no inspection would be conducted and also no delivery of store to be received from the Rate Contract Holder.

Incharge Marketing

Page 93: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

93/127 (4) Purchase Department’s (DDO’s)/Quality Assurance Officer would be responsible for the any

consequence which may arise due to non compliance of the above conditions and shall keep CSIDC indemnified of any such consequence.

SCHEDULES ANNEXED: 1. Schedule “A” Description of Stores, Prices, Duties / Taxes. 2. Annexure -“B” Technical Particulars of Item Water Tanker. 3. Schedule “B” Special conditions of contract (if any). 4. Schedule “C” Information to DDOs about parallel rate contracts. 5. Schedule “D” Format for Drawal Report.

Total- 18 Pages. Yours faithfully,

(Subas Chandra Bhagat) Incharge Marketing

For and on behalf of the purchaser named in CSIDC Form No.2

Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/RE/7923 Dt.: 12-04-2017 +

Copy to :-

1. The Secretary, Chhattisgarh Vidhan Sabha, Raipur.

2. The Registrar, Honourable High court Chhattisgarh, Bilaspur.

3. The Accountant General Chhattisgarh State, Raipur.

4. All HODs of Chhattisgarh Govt.

5. All The Collectors, Chhattisgarh Govt.

6. The Director Treasury, Chhattisgarh Govt. with a request to circulate the copy of Rate Contract to all Direct Demanding Officers of your

institution against issue of purchase order (Indent) in favor of Rate Contract Holders of CSIDC,

7. (i) The Director Education Department (DPI) Indrawati Bhawan, Naya Raipur (C.G.) (ii) The Commissioner Tribal Welfare Department Indrawati Bhawan, Naya Raipur (C.G.) (iii) The Commissioner Directorate of Women & Child Development Indrawati Bhawan, Naya Raipur (C.G.) (iv) Principle Chief Conservator of Forest C.G. Raipur.

8. (i) CSIDC (DEPARTMENTAL TECHNICAL WING) (ii) ADG (Q & A) , DGS&D, Jeewan Tara Building 5 Parliament Street New Delhi 110001 (iii) Manager (Operation) Indian Register of Shipping, Senior MIG-2, Secter A, 1st Floor, Infront

of Bank of India Indrapuri Bhopal. (iv) Chief Engineer, PDIL, 4th floor, 4/2 Karaya Road, 67 Shekespeare Sarani, Kolkata (W.B.) (v) General Manager (Inspection) RITES Ltd., Churchgate Station Road, Second Floor, M.K.

Road, Mumbai-400020 (vi) Operations Manager SGS India Pvt, Ltd. 43, RR Arcade, Zone-2, MP Nagar, Bhopal (MP)-

462011.

9. Manager (Tender), Marketing Div., CSIDC Ltd., Raipur. He is requested to maintain a master file of Rate Contract.

10. Computer cell, CSIDC Ltd., Raipur to release Rate Contract on CSIDC website.

11. Main file of Item- “Water Tanker.”

Incharge Marketing

For and on behalf of the purchaser named in CSIDC Form No.2

Page 94: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

94/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/RE/7923 Dt.: 12-04-2017

SCHEDULE “A” Description of Stores, Prices, Duties/Taxes

For the supply of Item- Water Tanker as per Annexure’A’ enclosed.

1. (a) NAME AND FULL ADDRESS OF :- M/s Rahul Enterprises, THE FIRM Office- 1016, Roshan Gagh,

Pushpa Nagar Road, Esh Bagh (M.P.) Mob.-9826469388, 9826038441 [email protected]

(b) NAME AND FULL ADDRESS OF :- M/s Rahul Enterprises, MANUFACTURER Office- 1016, Roshan Gagh,

Pushpa Nagar Road, Esh Bagh (M.P.)

(c) Catagery :- GEN

2. VALIDITY OF RATE CONTRACT :- From 12-04-2017 to 11-04-2018

3. DESCRIPTION OF ITEM- Water Tanker.

Item Code No.

Item Description Class Rate ( ) F.O.R. Destination

ED NA & VAT Extra if Applicable

Rate Per Unit 1 2 3

WT001 (A) Tankers Mounted On Four Wheel Trolley (With 7.50 X 16 Tyre & Tube) With Leaf Spring 5000 Liters

127139.00

WT002 4500 liters 123143.00 WT004 (A) Tankers Mounted On Four Wheel Trolley (With 7.50 X 16 Tyre &

Tube) Without Leaf Spring 5000 Liters 119060.00

WT005 4500 liters 115871.00 WT006 3500 liters 102104.00 WT007 (B) Tankers Mounted On Two Wheel Trolley With Leaf Spring 3500 Liters 90889.00 WT008 2500 Liters 80259.00 WT009 (B) Tankers Mounted On Two Wheel Trolley Without Leaf Spring 3500

Liters 88763.00

WT010 2500 Liters 73677.00 WT011 (C) Tankers Mounted On Four Wheel Trolley: (With 9x20 Tyres Tubes)

4000 Liters 122249.00

WT012 5000 Liters 127669.00 WT013 (D) Tankers Mounted On Two Wheel Trolley With Leaf Spring 4000 Liters 104178.00 WT014 4500 liters 110413.00 WT015 5000 Liters 117785.00 WT016 5500 Liters 123109.00 WT017 (D) Tankers Mounted On Two Wheel Trolley Without Leaf Spring: 4000

Liters 100457.00

WT018 4500 liters 106303.00 WT019 5000 Liters 114755.00 WT020 5500 Liters 120123.00

Note :- Technical particulars as per Annexure B enclosed

(Subas Chandra Bhagat)

Incharge Marketing

Page 95: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

95/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/RE/7923 Dt.: 12-04-2017 4. TERMS OF DELIVERY : F. O. R Destination (Any where in C.G. State)

5. EXCISE DUTY : Not Applicable

6. SALES TAX /VAT : Extra, if applicable

TIN No. 23291704193 Address:-

M/s Rahul Enterprises, Office- 1016, Roshan Gagh, Pushpa Nagar Road, Esh Bagh (M.P.)

7. DELIVERY PERIOD : 45 Days

8. a. ANNUAL TURN OVER/ : 2013-14 . 301.89 Lac. 2014-15 . 158.56 Lac. 2015-16 . 251.67 Lac.

b. MONETARY LIMIT : NM

c. INSTALLED CAPACITY : (As per NSIC Certificate Issued By Indore (M.P.)

Water Tanker

Description Annum Capacity

Water Tanker 230 Nos.

9. SLAB DISCOUNT (IF ANY) : Nil 10. PRICES : Prices are Firm and Final 11. MINIMUM QUANTITY IN : Not Mentioned. SINGLE SUPPLY ORDER 12. STATUS OF RC HOLDING : Manufacturer

FIRM 13. REGISTRATION STATUS : Manufacturer is Registered with NSIC vide No.

NSIC/GP/IND/2014/0009750 Valid up to 19-12-2018 14 BIS LICENSE : Not Applicable 15. PAYING AUTHORITY : As Mentioned in supply order to be issued by Direct Demanding Officers (DDOs).

16. PAYMENT TERMS : The payment of full 100% of prices of the stores of each consignment there-of will be made after receipt and acceptance of the stores by the consignee/interim consignee in full and good condition within 20 days as per SPR rule No.11, if the bills are in order. In case of delay in payment without any reason the department will be liable to pay interest as per prevailing bank rate. Bills are to be submitted in the prescribed form of the paying authority of purchaser / indenter and are to be supported with inspection note issued by the inspector and consignee’s Receipt Certificate.

(Subas Chandra Bhagat)

Incharge Marketing

Page 96: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

96/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/RE/7923 Dt.: 12-04-2017

17 INSPECTION AUTHORITY : CSIDC (DEPARTMENTAL TECHNICAL WING) Bhilai OR ADG (Q & A) , DGS&D, Jeewan Tara Building 5 Parliament Street New Delhi 110001 OR Manager (Operation) Indian Register of Shipping Senior MIG-2, Secter A, 1st Floor, in front of Bank of India Indrapuri Bhopal (M.P.)

OR Chief Engineer, Project & Development India Ltd. 4st floor, 4/2 Karaya Road, 67 Shekespeare Sarani Kolkata (W.B.)

OR General Manager (Inspection) RITES Ltd. Churchgate Station Road, Second Floor, M.K. Road, Mumbai- 400020 (Mah) OR

Manager (Operations) SGS India Pvt. Ltd. 43, RR Arcade, Zone-2, MP Nagar, Bhopal-462011. (M.P.)

18 QUALITY ASSURANCE: CSIDC (DEPARTMENTAL TECHNICAL WING) Bhilai

Shri Sanjiv Awasthy Mob. No. 9926999936 Email- [email protected] OR Dy. Director (Q&A), DGS&D, Bhilai (C.G.) DGS&D, Sector 1, Street-10 Old Telegraph Office, Bhilai (C.G), Fax No.- 0788-2223374 OR Manager (Operation) Indian Register of Shipping Senior MIG-2, Secter A, 1st Floor, in front of Bank of India Indrapuri Bhopal. (M.P.) Shri Amit Kumar Gupta Mob. No. 8871453225] M. Nazim Athar Mob. No. 8085182339

E-mail- [email protected] OR

Chief Engineer, Project & Development India Ltd. 4st floor, 4/2 Karaya Road, 67 Shekespeare Sarani Kolkata (W.B.) Fax No. 033-22873274 OR

General Manager (Inspection) RITES Ltd. Rajnish Ahuja Western Region (Inspection) Pho. No 2201- 2523/5573 Direct 2201 7434 Mob. 08600 017717 Fax 022 22084155, 2222016219

E-mail- [email protected], [email protected] OR

Manager (Operations) SGS India Pvt. Ltd. 43, RR Arcade, Zone-2, MP Nagar, Bhopal-462011. (M.P.) Shri Jitendra Raj Mob. No. 9752848321

E-mail- [email protected]

(Subas Chandra Bhagat)

Incharge Marketing

Page 97: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

97/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/RE/7923 Dt.: 12-04-2017 19. PLACE WHERE THE STORES At Manufacturer’s Factory at

ARE TO BE OFFERED FOR M/s Rahul Enterprises, INSPECTION Office- 1016, Roshan Gagh,

Pushpa Nagar Road, Esh Bagh (M.P.)

20 INSPECTION CHARGES : Inspection charges 0.60%+ Service Tax As applicable to be paid extra at the time of inspection to Quality Assurance Officer which will be billed by the unit along with bill of the material and will be reimbursed by the paying authority of DDO.

21. SECURITY DEPOSIT : As per General conditions of contract, CSIDC Form No. 1, Clause 7,the Purchaser/DDOs may require the contractor to furnish a security deposit which shall be made after issue of the acceptance of the supply order within the period specified by the purchaser / DDOs. Such security deposit shall not ordinarily exceed 3% . The security shall be in form of Demand Drafts issued by any of the Scheduled Commercial Banks. No other form of security is to be accepted. The security deposit amount is to be refunded after successful completion of the supply.

22. Special Note 1. Purchasing Departments/end user will ensure to sending the copy of every Purchase order to this office. 2. Purchasing Departments/end user will ensure to Pre Dispatch inspection of stores through Inspection agency enlisted in the CSIDC Panel. 3. Purchasing Departments/end user will be responsible for ensuring the Quality of accepted stores. As per the Tech. Specification. 4. Purchasing Department/end user shall be ensure to execute the Integrity Pact between BUYER and BIDDER/ SUPPLIER in accordance with the letter vide No.799/eq-l- @2013 New Raipur Dated 10.07.2013 and 243/fo-@fu- @pkj@2013 New Raipur Dated 06.07.2013 issued by the Chief Secretary. Govt. of Chhattisgarh. 5. Purchasing Department/end user will ensure to issue the

Purchase Order in accordance with the Store Purchase Rules-2002 (As Amended) vide Clause No.-13

(Subas Chandra Bhagat) Incharge Marketing

Page 98: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

98/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/RE/7923 Dt.: 12-04-2017

Annexure-B CSIDC/MKD/TECH/2016-17/28

SPECIFICATION FOR WATER TANKER MOUNTED ON FOUR / TWO WHEEL TROLLEY

TSC 23-11-2016

(E) SPECIFICATION OF PRODUCTS

(A) TANKERS MOUNTED ON FOUR WHEEL TROLLEY (WITH 7.50 X 16 TYRE & TUBE) WITH LEAF SPRING OR WITHOUT LEAF SPRING

1. Chassis:

The Chassis shall be fabricated as per standard practice to mount the MS tank. All the joint shall be welded with gusset plates wherever required as per standard practice.

The Chassis frame shall have two longitudinal member and 5 cross members of channel

section of size 125 x 65 mm (ISMC) for 4500 & 5000 lts. Capacity. For 3500 lts. Capacity the chassis frame shall have two longitudinal members and 4 cross members of channel section of size 100 x 50 mm (ISMC) The overall approximate dimensions of various tanker trolley chassis shall be as under:- -----------------------------------------------------------------------------------------------------

S.No. Approx.Cap Length Width -----------------------------------------------------------------------------------------------------

1. 5000 liters 4 metres 1.00 mtr. 2. 4500 liters 4 meters 1.00 mtr. 3. 3500 liters 3.5 meters 1.00 mtr.

-----------------------------------------------------------------------------------------------------

2. Turn table:

The turn table frame shall be made out of 100x50mm (ISMC) MS channel with cross support, fixed with double rings fabricated from Angle Iron 40x40x6 mm and with 40mm diameter centre pin with suitable washer and locking arrangement.

3. Draw Bar:

Draw bar shall be in triangular construction made out of ISMC of size 100x50 mm with spring loaded eyehook made of 40mm dia MS bar.

The straight length of draw bar should be 150 cms including eye hook. Draw bar shall be hinged with the frame of turn table by 500 x 25mm Ms round bar having locking arrangement at both the end.

4. Axle & Brake assembly:

Axle shall be made from 63 x 63mm square bar with both the end machined, threaded and fitted with hubs and hexagonal lock nut, fitted with twin taper roller bearings, and provided with grease nipples for greasing the moving parts. For braking mechanical-internal expanding type brakes with suitable drums. hand operated, on rear wheels compete, with steel rod, clamps, springs and hand lever be provided.

(S.N. Chopra)

Incharge PS-III

Page 99: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

99/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/RE/7923 Dt.: 12-04-2017

5. Leaf Spring:

Four sets of leaf spring consisting of 13 leaves of size minimum 70 x 10mm, 1000mm long (distance between two pin) of alloy steel shall be provided. These leaf spring shall be fixed with frame by means of complete cast iron bracket assembly.

6. Tyres, tubes & wheel Assembly :

Four number tyre of 7.50 x 16 and tubes of standard make, Shall be provided with double plated rims 5mm thick with 5/6 nos. holes.

7. Water tanker:

The Water Tanker shall have capacity of 5000, 4500 & 3500 litres approx., and shall be manufactured in elliptical shape/ semi elliptical shape. The approx size of Water Tanker shall be as follows:- ----------------------------------------------------------------------------------------------------------- S. No. Approx. Major Axis Minor Axis Length ----------------------------------------------------------------------------------------------------------- 1. 5000 lit. 1.95 mtrs. 1.05 mtrs. 3.6 mtrs. 2. 4500 lit. 1.75 mtrs. 1.05 mtrs. 3.6 mtrs. 3. 3500 lit.. 1.5 mtrs 1.05 mtrs. 3.0 mtrs -----------------------------------------------------------------------------------------------------------

The tank shall be made out of 3.15mm thick MS sheet, and end plates of 4.0mm thick MS plate. End plate shall be maximum in two piece.

The tank shall be reinforced from inside by welding four numbers of elliptical rings made of 40 x 40 x 6mm MS angle one at both ends and two in between at suitable distance (total 04 on.) for 4500 & 5000 lts capacity. For 3500 lts capacity angle rings shall be provided at both ends and one at the middle (total 03 no.)

Two nos. baffle plate of 3.15mm thick MS sheet shall be provided in side the tank. These plates shall be properly welded with the central ring as per the standard practice. The height of baffle plate shall be 20cm. More than half of the height of tank. For 3500 lts capacity only one baffle plate be provided.

8. Manhole:

Two manhole with hinged cover shall be provided at the top of the tank. The cover of tank shall be fabricated from 3.15 thick MS sheet. The collar of the cover and manhole shall be made out of 4.00 mm MS strip. Locking arrangement for cover shall be provided; The manhole covers shall be such fabricated so that no foreign material may enter into the tank.

A 300 mm wide five steps ladder made of 32 x 32 x 2.5/3mm Ms angle be provided at left hand on rear side of the tanker (i.e. cleaner seat side). One no. 300 mm wide platform for full length at left hand be provided at appropriate level. The platform frame be made from Angle Iron 32 x 32 x2.5/3mm and 2.5 mm thick MS sheet. A suitable railing of 150 mm height on full length of platform shall be provided at the outer side of the platform by using 25x25x2.5/3mm Angle Iron or 25mm pipe and 2.0 mm MS sheet.

(S.N. Chopra) Incharge PS-III

Page 100: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

100/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/RE/7923 Dt.: 12-04-2017

The rear wheels shall be covered with mudguards fabricated out of 1.6mm thick MS sheets,

as per standard practice.

The Water Tanker shall be fixed on the chassis by 8 nos. suitable arranged fabricated shoes (box type brackets) from 5mm thick plates and base plate of approximate size 23x17 cms. and 12mm thick OR made of suitable ISMC bolted to the chassis with suitable ‘U’ clamps (two nos. in each base) The box brackets width shall not be less than 60mm and the bottom of the tank shall be provided with 6 mm thick and 120mm wide saddle plates for full width of the tank as a base for the shoes (box type brackets).

9. Ball Bering No. 31213 must be used. (B) TANKERS MOUNTED ON TWO WHEEL TROLLEY WITH LEAF SPRING OR

WITHOUT LEAF SPRING 1. Chassis:

The Chassis shall be fabricated as per standard practice to mount the MS tank. All the joint shall be welded with gusset plates wherever required as per standard practice.

The Chassis frame shall have two longitudinal member and 4 cross members of channel

section of size 100 x 50 mm (ISMC).

The overall approximate dimensions of various tanker trolley chassis shall be as under:- -----------------------------------------------------------------------------------------------------

S.No. Approx.Cap Length Width -----------------------------------------------------------------------------------------------------

1. 3500 liters 3.0 metres 0.80 mtr. 2. 2500 liters 2.5 meters 0.80 mtr.

----------------------------------------------------------------------------------------------------- 2. Draw bar:

Draw bar shall be in triangular construction made out of MS channel of size 100 x 50 mm with spring loaded eyehook made of 40 mm dia MS bar.

The straight length of draw bar should be 150 cms including eye hook.

3. Axle & Brake assembly:

Axle shall be made from 63 x 63mm square bar with both the end machined and threaded and provided with iron hubs and hexagonal lock nut, fitted with twin taper roller bearings and provided with grease nipples for greasing the moving parts.

4. Leaf spring:

Two sets of leaf spring consisting of 13 leaves of size 70 x 10mm minimum 1000 mm long (distance between two pin) of alloy steel shall be provided. These leaf spring shall be fixed with frame by means of complete cast iron bracket assembly.

5. Tyres, tubes & wheel Assembly:

(S.N. Chopra)

Incharge PS-III

Page 101: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

101/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/RE/7923 Dt.: 12-04-2017

Two number tyres of 7.50 x 16 and tubes of standard make shall be provided with double plated rims 5 mm thick with 5/6 nos. holes for 2500 lts. Capacity tanker. For 3500 lts. Capacity two number tyres of 9x16 and tubes of standard make shall be provided.

6. Water Tanker:

The Water Tanker Should have capacity of 2500 & 3500 liters approx. Manufactured in elliptical. Shape. The approx. size of Water Tanker are as follows :-

-------------------------------------------------------------------------------------------------------------- S.No. Approx.Cap Major Axis Minor Axis Length -------------------------------------------------------------------------------------------------------------- 1. 3500 liters 1.5 mtrs 1.05 mtrs 3.0 mtrs. 2. 2500 liters 1.20 mtrs 1.05 mtrs 2.5 mtrs. --------------------------------------------------------------------------------------------------------------

The tank shall be made out of 3.15 mm thick MS sheet, and end plates of 4.0 thick MS plate. End plate should be maximum two pieces.

The tank shall be reinforced from inside by welding three numbers of elliptical rings made of 40 x 40 x 6mm MS angle one at both ends and one in between at suitable distance.

One baffle plate of 3.15mm shall be provided inside the tank. These plates shall be properly welded with the central ring as per the standard practice. The height of baffle plate shall be 20 cm more than half of the height of tank.

7. Manhole:

One manhole with hinged cover shall be provided at the top of the tank. The cover of tank shall be fabricated from 3.15 thick MS sheet. The collar of the cover and manhole shall be made out of 4.00 mm MS strip. Locking arrangement for cover shall also be provided; The manhole cover shall be such fabricated so that no foreign material may enter in to the tank.

A 300 mm wide three steps ladder made of 32x32x2.5/3mm MS angle be provided at left hand on front side of the tanker (i.e. cleaner seat side). One no. 300mm wide platform for full length at left hand be provided at appropriate level. The platform frame be made from angle iron 32x32x2.5/3mm and 2.5 mm thick MS sheet. A suitable railing of 150mm height on full length of platform shall be provided at the outer side of the platform by using 25x25x3mm Angle Iron of 25mm pipe and 2.0mm MS Sheet.

The water tanker shall be fixed on the chassis by 6 nos. suitable arranged fabricated shoes (box type brackets) from 5mm thick plates and base plate of approximate size 23 x 17 cms. and 12 mm thick OR made of suitable ISMC bolted to the chassis with suitable ‘U’ clamps (two nos. in each base). The box brackets width shall not be less than 60 mm and the bottom of the tank shall be provided with 6 mm thick and 120 mm wide saddle plates for full width of the tank as a base for the shoes (box type brackets.)

8. Ball Bering No. 31213 must be used.

(C) TANKERS MOUNTED ON FOUR WHEEL TROLLEY: (WITH 9X20 TYRES TUBES)

1. Chassis: The Chassis shall be fabricated as per standard practice to mount the MS tank. All the joint

shall be welded with gusset plates wherever required as per standard practice.

(S.N. Chopra)

Incharge PS-III

Page 102: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

102/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/RE/7923 Dt.: 12-04-2017

The chassis frame shall have two longitudinal member and 3 cross members of channel section of size 150x75mm (ISMC) for 4000 & 5000 It. Capacity.

The width of the chassis frame shall be of 1.0mt and length shall be equal to the length of the tank.

2. Turn table:

The turn table frame shall be made out of 100x50mm (ISMC or equivalent) MS channel with cross support, fixed with double rings fabricated out of Angle Iron 40x40x6 mm and with 40mm diameter centre pin with suitable washer and locking arrangement.

3. Draw Bar:

Draw bar shall be in triangular construction made out of Ms Channel of size 100x50 mm with spring loaded eyehook made of 40mm dia MS bar.

The straight length of draw bar should be 150 cms including eye hook. Draw bar shall be hinged with the frame of turn table by 100x25mm MS round bar having locking arrangement at both the end.

4. Axle & Brake assembly:

Axle shall be made from 63x63mm square bar of 1750mm length with both the end machined and threaded and provided with iron hubs and hexagonal lock nut, fitted with twin taper roller bearings, and provided with grease nipples for greasing the moving parts. For braking mechanical-internal expanding type brakes with suitable drums, hand operated, on rear wheels compete, with steel rod, clamps, springs and hand lever be provided.

5. Leaf Spring:

Four sets of leaf spring consisting of 13 leaves of size 70x11 mm minimum 1000mm long (distance between two pin) of alloy steel shall be provided. These leaf spring shall be fixed with frame by means of complete cast iron bracket assembly.

6. Tyres, tubes & wheel Assembly :

Four number tyre of 9 x 20 and tubes of standard make. Shall be provided with double plated rims 5 mm thick with 5/6 nos. holes. For four wheel trolley.

7. Water tanker:

The Water Tanker shall have capacity of 5000 & 4000 litres approx. manufactured in semi elliptical shape.

The minor axis of the tank shall be of 1.05 mtr. The manufacturer shall design major axis

and length of the semi elliptical tank accordingly. The tank shall be made out of 3.15 mm thick MS sheet, and end plates of 4.0 thick MS plate.

End plate should be maximum two pieces.

(S.N. Chopra)

Incharge PS-III

Page 103: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

103/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/RE/7923 Dt.: 12-04-2017

The tank shall be reinforced from inside by welding three numbers of elliptical rings made of 40 x 40 x 6mm MS angle one at both ends and one in between at suitable distance.

Two baffle plate of 3.15mm shall be provided in side the tank. These plates shall be properly

welded with the central ring as per the standard practice. The height of baffle plate shall be 20 cm more than half of the height of tank.

8. Manhole:

Two manhole with hinged cover shall be provided at the top of the tank. The cover of tank shall be fabricated from 3.15 thick MS sheet. The collar of the cover and manhole shall be made out of 4.00 mm MS strip. Locking arrangement for cover shall also be provided; The manhole cover shall be such fabricated so that no foreign material may enter in to the tank.

A 300 mm wide three steps ladder made of 30x30x3mm MS angle be provided at left hand

on front side of the tanker. One no. 300mm wide platform for full length at left hand be provided at appropriate level. The platform frame be made from angle iron 35x35x3mm and 2.5 mm thick MS sheet. A suitable railing of 150mm height on full length of platform shall be provided at the outer side of the platform by using 25x25x3mm Angle Iron of 25mm pipe and 2.0mm MS Sheet.

The water tanker shall be fixed on the chassis by 8 nos. suitable arranged fabricated shoes

(box type brackets) from 5mm thick plates and base plate of approximate size 23 x 17 cms. and 12mm thick bolted to the chassis or made of 100x50mm channel properly covered with sheet of 3.15mm suitable ‘U’ clamps (two nos. in each base). The box brackets width shall not be less than 60 mm and the bottom of the tank shall be provided with 6 mm thick and 120 mm wide saddle plates for full width of the tank as a base for the shoes (box type brackets.)

9. Ball Bering No. –31213 must be used. (D) TANKERS MOUNTED ON TWO WHEEL TROLLEY WITH LEAF SPRING OF

WITHOUT LEAF SPRING: 1. Chassis:

The Chassis shall be fabricated as per standard practice to mount the MS tank. All the joint shall be welded with gusset plates wherever required as per standard practice.

The Chassis frame shall have two longitudinal members and 4 cross members of channel

section of size 150 x 75 mm (ISMC) The overall approximate dimensions of various tanker trolley chassis shall be as under:- -----------------------------------------------------------------------------------------------------

S.No. Approx.Cap Length Width -----------------------------------------------------------------------------------------------------

1. 4000 liters 3.3 metres 1.2 mtr. 2. 4500 liters 3.5 meters 1.2 mtr. 3. 5000 liters 3.5 meters 1.2 mtr. 4. 5500 liters 3.7 metres 1.2 mtr.

-----------------------------------------------------------------------------------------------------

(S.N. Chopra) Incharge PS-III

Page 104: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

104/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/RE/7923 Dt.: 12-04-2017 WATER TANKERS MOUNTED ON FOUR/TWO WHEEL TROLLEY 2. Draw Bar:

Draw bar shall be in triangular construction made out of MS channel of size 150x75 mm with spring loaded eyehook made of 40mm dia MS bar.

The minimum straight length of draw bar should be 150 cms including eye hook.

3. Axle & Brake assembly:

Axle shall be made from 72 x 72mm square bar with both the end machined and threaded and provided with iron hubs and hexagonal lock nut, fitted with twin taper roller bearings and provided with grease nipples for greasing the moving parts.

4. Leaf Spring:

Two sets of leaf spring consisting of 13 leaves of 4000 & 4500 Ltr. And 19 leaves for 5000 & 5500 ltr. Cap. Of size minimum 70 x 10mm minimum 900mm long (distance between two pin) of alloy steel shall be provided. These leaf spring shall be fixed with frame by means of complete cast iron bracket assembly.

5. Tyres, tubes & wheel Assembly :

Two number tyre of 9 x16 / 9x16 and tubes of standard make Shall be provided with double plated rims 5mm thick with 8 nos. holes.

6. Water tanker:

The Water Tanker should have capacity of 5000, 5500 litres approx. manufactured in elliptical shape. The approx size of Water Tanker are as follows:- ----------------------------------------------------------------------------------------------------------- S. No. Approx. Major Axis Minor Axis Length ----------------------------------------------------------------------------------------------------------- 1. 4000 lit. 1.65 meters 1.11 mtrs. 2.8 mtrs. 2. 4500 lit. 1.70 meters 1.13 mtrs. 3.0 mtrs. 3. 5000 lit. 1.80 meters 1.18 mtrs. 3.0 mtrs 4. 5500 lit. 1.80 meters 1.22 mtrs. 3.2 mtrs. -----------------------------------------------------------------------------------------------------------

WATER TANKERS MOUNTED ON FOUR/TWO WHEEL TROLLEY

The tank shall be made out of 3.15mm thick MS sheet, and end plates of 4.0mm thick MS plate. End plate should be in maximum two pieces.

The tank shall be reinforced form inside by welding three numbers of elliptical rings made of

40x40x6mm MS Angle one at both ends and one in between at suitable distance.

One baffle plate of 3.15mm shall be provided in side the tank. These plates shall be properly welded with the central ring as per the standard practice. The height of baffle plate shall be 20cm. more than half of the minor axis of tank.

(S.N. Chopra)

Incharge PS-III

Page 105: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

105/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/RE/7923 Dt.: 12-04-2017 7. Manhole:

One manhole with hinged cover shall be provided at the top of the tank. The cover of tank shall be fabricated from 3.15 thick MS sheet. The collar of the cover and manhole shall be made out of 4.00 mm MS strip. Locking arrangement for cover shall also be provided; The manhole cover shall be such fabricated so that no foreign material may enter in to the tank.

A 300 mm wide three steps ladder made of 32x32x2.5/3mm MS angle be provided at

left hand on front side of the tanker (i.e. cleaner seat side). One no. 300mm wide platform for full length at left hand be provided at appropriate level. The platform frame be made from angle iron 32x32x2.5/3mm and 2.5 mm thick MS sheet. A suitable railing of 150mm height on full length of platform shall be provided at the outer side of the platform by using 25x25x3mm Angle Iron of 25mm pipe and 2.0mm MS Sheet.

The water tanker shall be fixed on the chassis by 6 nos. suitable arranged fabricated shoes (box type brackets) from 5mm thick plates and base plate of approximate size 23 x 17 cms. and 12 mm thick OR made of suitable ISMC bolted to the chassis with suitable ‘U’ clamps (two nos. in each base). The box brackets width shall not be less than 60 mm and the bottom of the tank shall be provided with 6 mm thick and 120 mm wide saddle plates for full width of the tank as a base for the shoes (box type brackets.)

Pump set stand shall be provided at rear side of the tank.

8. Ball Bering No. 31213 must be used.

WATER TANKERS MOUNTED ON FOUR/TWO WHEEL TROLLEY

1. Outlet:

Outlet 75 mm NB class ‘A’ GI nipple of 10 length (minimum) be provided at the rear of the tank along with required 75 mm GM full way wheel valve, followed by another 20 cm length nipple for connecting a hose pipe. A Drain plug of 50 mm shall be provided at the bottom of the tank at suitable place.

2. Accessories:

The water tanker shall be provided with 2 nos. of reflectors, number plate and tool box etc. The size of tool box should be 600 mm (L) x 300 mm (W) x 300 mm (H) made of 2.5 mm MS sheet.

3. Painting & Finishing:

The tanker should be spray painted, with printing coat of red-oxide and two coat of synthetic enamel paint and color as desired by consignee. Interior of the tank should be painted with two coat of suitable primer followed by Non-poisonous white rubber paint.

4. Guarantee:-

The manufacturer shall furnish guarantee for one year against manufacturing defects leakage etc., along with tenders incorporating that in case of complaint they shall undertake satisfactory repairs within 10 days free of cast.

(S.N. Chopra) Incharge PS-III

Page 106: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

106/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/RE/7923 Dt.: 12-04-2017

5. Inspection:-

The inspection of water tanker shall be carried out by of CSIDC, Ltd. Approved Inspection Agencies

6. Ball Bering No. 31213 must be used.

Note:- If required minor deviation/amendment in specification may be done, after taking approval from CSIDC, Ltd,.

Recommended by Technical Specification Committee Dated 23-11-2016

(S.N. Chopra)

Incharge PS-III

Page 107: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

107/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/RE/7923 Dt.: 12-04-2017

SCHEDULE ‘B’

(SPECIAL CONDITION OF CONTRACT) ISI Pressure Cooker

Rate Contract Will be governed by the Terms & Conditions laid down in the

CSIDC FORM NO. 1 & 2

(Subas Chandra Bhagat) Incharge Marketing

Page 108: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

108/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/RE/7923 Dt.: 12-04-2017

SCHEDULE “C” LIST OF PARALLEL RATE CONTRACT FOR ITEM- Water Tanker

(Subas Chandra Bhagat) Incharge Marketing

S.No. Name of Tenderers Valid Up to Rate Contract No.

1. M/s Agrahari Agrotech Industries, Village-Bori, Tah & Dist.- Rajnandgaon Mob-9753072555

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/AAI/7915

2. M/s G.V. Industries, 22 A, Industrial Area, Dhar-454001 (M.P.) Mob-9425046639, 9826469388

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/G.V.I/7916

3. M/s National Engineering Works, Opp. Sirpur Lake Indore Ahmedabad Road, Indore (M.P.), Mob-07000233648

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/NEW/7920

4. M/s Netam Engineering Works, Audhogik Area, Bhakhara Road, Villa-Arjuni, Dhamtari, Mob-9406021763, 8602729134

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/NEW/7921

5. M/s New Malwa Agro & Fabricators, Plot No.-59, Sec-C, Sirgitti, Industrial Area, Bilaspur, Mob-9425046639, 7772086742

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/NMA&F/7922

6. M/s Rahul Enterprises, Office- 1016, Roshan Gagh, Pushpa Nagar Road, Esh Bagh (M.P.) Mob.-9826469388, 9826038441

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/RE/7923

7. M/s Shri Sai Steel Industries, Industrial.Area Nainpur, Surajpur, Distt.-Surajpur (C.G.) -497229 Mob.-9826649514 Email- [email protected]

17-05-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/SSSI/7919

Page 109: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

109/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/RE/7923 Dt.: 12-04-2017

SCHEDULE – “D”

FORMAT FOR QUATERLY DRAWAL REPORT Name of the Firm __________________ I- Jan-Mar Report No. __________________ II- Apr-June Rate Contract No. __________________ III- July-Sept. Date of Submission __________________ IV- Oct - Dec Total Position of Order against Rate Contract till the submission of Report. S.No. Name of

Department Quantity and Value of Orders Received (Rs.)

Quantity and Value of Orders Executed (Rs.)

Balance Quantity and Value to be Supplied (Rs.)

Reasons

Foot 1. Value indicate should be a) Value of orders received during the quarter-Rs.

Total value inclusive of all Taxes duties and incidental b) Value of orders supplied during the quarter-Rs. Charges

2. Nil report should also be Submitted.

(Subas Chandra Bhagat) Incharge Marketing

Page 110: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

110/127

Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh Undertaking) 1st Floor Udhyog Bhawan Ring Road No. -1, Telibhanadha Raipur 492006 (C.G) EPABX No.-91771-6002071-73, Tele Fax : 91771-2583793 & 91771- 4057624 (MKT) CIN- U45203CT1981SG001853 PAN – AABCM6288N Service Tax Regn. No- AABCM6288NSD004. Website: www. csidc.in, Email : [email protected], [email protected]

No./CSIDC/MKD/PS-III/16-17/ Raipur, Dated : Registered A/D Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/SSSI/7919 Dt.: 17-05-2017

To, M/s Shri Sai Steel Industries, Industrial.Area Nainpur, Surajpur, Distt.-Surajpur (C.G.) -497229 Mob.-9826649514 Email- [email protected] Sub :- Rate Contract for the supply of Water Tanker (Valid From dated 17-05-2017 to 10-04-2018)

Ref :- (I) This Office Tender Enquiry No. CSIDC/MKD/16-17/143/12768

(II) Your Offer acceptance along with undertaking submitted on dated 18-04-2017 & dated 17-05-2017

Dear Sir,

You are hereby informed that your above referred tender read with subsequent letters mentioned above for the Stores specified in the Schedules annexed has been accepted. This Rate Contract will be governed by the terms and conditions brought in CSIDC Form No.1 & 2. The Rate Contract and the Schedules annexed hereto shall be the sole repository of this Rate Contract / Transaction. You are required to show the original INK-SIGNED subject Rate Contract to the satisfaction of Direct Demanding Officer who will place the supply order as per instructions contained in CSIDC form No. 2 and also to the Quality Assurance Officer for inspection purpose and to the Paying Authority at the time of getting the payment .

Conditions to be fulfilled by the Purchaser Department (DDO’s) for purchase of store from the Rate Contract holders and Quality Assurance Officer for Inspection of store before delivery :-

It is sole responsibility of the Purchase Department’s (DDO’s) and Quality Assurance Officer to comply with the following conditions as a pre-requisite before accepting delivery/conducting Inspections – (1) Purchase Department’s (DDO’s) shall ensure the validity of following documents applicable for the

Rate Contract Holder to his satisfactions :- A. UAM/EM Part-II, Valid Operational Certificate and Competency Certificate. B. PAN Card No., Sales Tax/VAT Tax Registration (TIN).

(2) The above set of documents (As applicable) are required to be inspected by the Quality Assurance Officer before conduction inspection of store.

(3) In case, on the date of delivery OR Inspection, if any of document as mentioned above are not valid OR the validity period of which has been expired. no inspection would be conducted and also no delivery of store to be received from the Rate Contract Holder.

Incharge Marketing

Page 111: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

111/127 (4) Purchase Department’s (DDO’s)/Quality Assurance Officer would be responsible for the any

consequence which may arise due to non compliance of the above conditions and shall keep CSIDC indemnified of any such consequence.

SCHEDULES ANNEXED: 1. Schedule “A” Description of Stores, Prices, Duties / Taxes. 2. Annexure -“B” Technical Particulars of Item Water Tanker. 3. Schedule “B” Special conditions of contract (if any). 4. Schedule “C” Information to DDOs about parallel rate contracts. 5. Schedule “D” Format for Drawal Report.

Total- 18 Pages. Yours faithfully,

(Subas Chandra Bhagat) Incharge Marketing

For and on behalf of the purchaser named in CSIDC Form No.2

Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/RE/7919 Dt.: 17-05-2017 +

Copy to :-

1. The Secretary, Chhattisgarh Vidhan Sabha, Raipur.

2. The Registrar, Honourable High court Chhattisgarh, Bilaspur.

3. The Accountant General Chhattisgarh State, Raipur.

4. All HODs of Chhattisgarh Govt.

5. All The Collectors, Chhattisgarh Govt.

6. The Director Treasury, Chhattisgarh Govt. with a request to circulate the copy of Rate Contract to all Direct Demanding Officers of your

institution against issue of purchase order (Indent) in favor of Rate Contract Holders of CSIDC,

7. (i) The Director Education Department (DPI) Indrawati Bhawan, Naya Raipur (C.G.) (ii) The Commissioner Tribal Welfare Department Indrawati Bhawan, Naya Raipur (C.G.) (iii) The Commissioner Directorate of Women & Child Development Indrawati Bhawan, Naya Raipur (C.G.) (iv) Principle Chief Conservator of Forest C.G. Raipur.

8. (i) CSIDC (DEPARTMENTAL TECHNICAL WING) (ii) ADG (Q & A) , DGS&D, Jeewan Tara Building 5 Parliament Street New Delhi 110001 (iii) Manager (Operation) Indian Register of Shipping, Senior MIG-2, Secter A, 1st Floor, Infront

of Bank of India Indrapuri Bhopal. (iv) Chief Engineer, PDIL, 4th floor, 4/2 Karaya Road, 67 Shekespeare Sarani, Kolkata (W.B.) (v) General Manager (Inspection) RITES Ltd., Churchgate Station Road, Second Floor, M.K.

Road, Mumbai-400020 (vi) Operations Manager SGS India Pvt, Ltd. 43, RR Arcade, Zone-2, MP Nagar, Bhopal (MP)-

462011.

9. Manager (Tender), Marketing Div., CSIDC Ltd., Raipur. He is requested to maintain a master file of Rate Contract.

10. Computer cell, CSIDC Ltd., Raipur to release Rate Contract on CSIDC website.

11. Main file of Item- “Water Tanker.”

Incharge Marketing

For and on behalf of the purchaser named in CSIDC Form No.2

Page 112: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

112/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/SSSI/7919 Dt.: 17-05-2017

SCHEDULE “A” Description of Stores, Prices, Duties/Taxes

For the supply of Item- Water Tanker as per Annexure’A’ enclosed.

1. (a) NAME AND FULL ADDRESS OF :- M/s Shri Sai Steel Industries, THE FIRM Industrial.Area Nainpur, Surajpur,

Distt.-Surajpur (C.G.) -497229 Mob.-9826649514

(b) NAME AND FULL ADDRESS OF :- M/s Shri Sai Steel Industries, MANUFACTURER Industrial.Area Nainpur, Surajpur,

Distt.-Surajpur (C.G.) -497229 Mob.-9826649514

(c) Catagery :- GEN

2. VALIDITY OF RATE CONTRACT :- From 17-05-2017 to 10-04-2018

3. DESCRIPTION OF ITEM- Water Tanker.

Item Code No.

Item Description Class Rate ( ) F.O.R. Dest

ED & VAT Extra As Applicable

Rs per Unit 1 2 3

WT001 (A) Tankers Mounted On Four Wheel Trolley (With 7.50 X 16 Tyre & Tube) With Leaf Spring 5000 Liters

127139.00

WT002 4500 liters 123143.00 WT004 (A) Tankers Mounted On Four Wheel Trolley (With 7.50 X 16 Tyre &

Tube) Without Leaf Spring 5000 Liters 119060.00

WT005 4500 liters 115871.00 WT006 3500 liters 102104.00 WT007 (B) Tankers Mounted On Two Wheel Trolley With Leaf Spring 3500 Liters 90889.00 WT008 2500 Liters 80259.00 WT009 (B) Tankers Mounted On Two Wheel Trolley Without Leaf Spring 3500

Liters 88763.00

WT010 2500 Liters 73677.00 WT011 (C) Tankers Mounted On Four Wheel Trolley: (With 9x20 Tyres Tubes)

4000 Liters 122249.00

WT012 5000 Liters 127669.00 WT013 (D) Tankers Mounted On Two Wheel Trolley With Leaf Spring 4000 Liters 104178.00 WT014 4500 liters 110413.00 WT015 5000 Liters 117785.00 WT016 5500 Liters 123109.00 WT017 (D) Tankers Mounted On Two Wheel Trolley Without Leaf Spring: 4000

Liters 100457.00

WT018 4500 liters 106303.00 WT019 5000 Liters 114755.00 WT020 5500 Liters 120123.00

Note :- Technical particulars as per Annexure B enclosed

(Subas Chandra Bhagat)

Incharge Marketing

Page 113: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

113/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/SSSI/7919 Dt.: 17-05-2017 4. TERMS OF DELIVERY : F. O. R Destination (Any where in C.G. State)

5. EXCISE DUTY : Not Applicable

6. SALES TAX /VAT : Extra, if applicable

TIN No. 22615004313 Address:-

M/s Shri Sai Steel Industries, Industrial.Area Nainpur, Surajpur, Distt.-Surajpur (C.G.) -497229 Mob.-9826649514

7. DELIVERY PERIOD : 45 Days

8. a. ANNUAL TURN OVER/ : 2015-16 . 62,04,101.00 2014-15 . 60,00,969.00 2013-14 . 1,53,18,098.00

b. MONETARY LIMIT : NM

c. INSTALLED CAPACITY : (As per DTIC EM Part-II Registration Certificate Issued By DTIC Surajpur

Water Tanker

Description Capacity/Per Annum

Water Tanker 30 Nos.

9. SLAB DISCOUNT (IF ANY) : Nil 10. PRICES : Prices are Firm and Final 11. MINIMUM QUANTITY IN : Not Mentioned. SINGLE SUPPLY ORDER 12. STATUS OF RC HOLDING : Manufacturer

FIRM 13. REGISTRATION STATUS : Manufacturer is Registered with UAM vide No.

CG27A0000018, Dt. 24-11-2009. 14 BIS LICENSE : Not Applicable 15. PAYING AUTHORITY : As Mentioned in supply order to be issued by Direct Demanding Officers (DDOs).

16. PAYMENT TERMS : The payment of full 100% of prices of the stores of each consignment there-of will be made after receipt and acceptance of the stores by the consignee/interim consignee in full and good condition within 20 days as per SPR rule No.11, if the bills are in order. In case of delay in payment without any reason the department will be liable to pay interest as per prevailing bank rate. Bills are to be submitted in the prescribed form of the paying authority of purchaser / indenter and are to be supported with inspection note issued by the inspector and consignee’s Receipt Certificate.

(Subas Chandra Bhagat)

Incharge Marketing

Page 114: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

114/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/SSSI/7919 Dt.: 17-05-2017

17 INSPECTION AUTHORITY : CSIDC (DEPARTMENTAL TECHNICAL WING) Bhilai OR ADG (Q & A) , DGS&D, Jeewan Tara Building 5 Parliament Street New Delhi 110001 OR Manager (Operation) Indian Register of Shipping Senior MIG-2, Secter A, 1st Floor, in front of Bank of India Indrapuri Bhopal (M.P.)

OR Chief Engineer, Project & Development India Ltd. 4st floor, 4/2 Karaya Road, 67 Shekespeare Sarani Kolkata (W.B.)

OR General Manager (Inspection) RITES Ltd. Churchgate Station Road, Second Floor, M.K. Road, Mumbai- 400020 (Mah) OR

Manager (Operations) SGS India Pvt. Ltd. 43, RR Arcade, Zone-2, MP Nagar, Bhopal-462011. (M.P.)

18 QUALITY ASSURANCE: CSIDC (DEPARTMENTAL TECHNICAL WING) Bhilai

Shri Sanjiv Awasthy Mob. No. 9926999936 Email- [email protected] OR Dy. Director (Q&A), DGS&D, Bhilai (C.G.) DGS&D, Sector 1, Street-10 Old Telegraph Office, Bhilai (C.G), Fax No.- 0788-2223374 OR Manager (Operation) Indian Register of Shipping Senior MIG-2, Secter A, 1st Floor, in front of Bank of India Indrapuri Bhopal. (M.P.) Shri Amit Kumar Gupta Mob. No. 8871453225] M. Nazim Athar Mob. No. 8085182339

E-mail- [email protected] OR

Chief Engineer, Project & Development India Ltd. 4st floor, 4/2 Karaya Road, 67 Shekespeare Sarani Kolkata (W.B.) Fax No. 033-22873274 OR

General Manager (Inspection) RITES Ltd. Rajnish Ahuja Western Region (Inspection) Pho. No 2201- 2523/5573 Direct 2201 7434 Mob. 08600 017717 Fax 022 22084155, 2222016219

E-mail- [email protected], [email protected] OR

Manager (Operations) SGS India Pvt. Ltd. 43, RR Arcade, Zone-2, MP Nagar, Bhopal-462011. (M.P.) Shri Jitendra Raj Mob. No. 9752848321

E-mail- [email protected]

(Subas Chandra Bhagat)

Incharge Marketing

Page 115: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

115/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/SSSI/7919 Dt.: 17-05-2017 19. PLACE WHERE THE STORES At Manufacturer’s Factory at

ARE TO BE OFFERED FOR M/s Shri Sai Steel Industries, INSPECTION Industrial.Area Nainpur, Surajpur,

Distt.-Surajpur (C.G.) -497229

20 INSPECTION CHARGES : Inspection charges 0.60%+ Service Tax As applicable to be paid extra at the time of inspection to Quality Assurance Officer which will be billed by the unit along with bill of the material and will be reimbursed by the paying authority of DDO.

21. SECURITY DEPOSIT : As per General conditions of contract, CSIDC Form No. 1, Clause 7,the Purchaser/DDOs may require the contractor to furnish a security deposit which shall be made after issue of the acceptance of the supply order within the period specified by the purchaser / DDOs. Such security deposit shall not ordinarily exceed 3% . The security shall be in form of Demand Drafts issued by any of the Scheduled Commercial Banks. No other form of security is to be accepted. The security deposit amount is to be refunded after successful completion of the supply.

22. Special Note 1. Purchasing Departments/end user will ensure to sending the copy of every Purchase order to this office. 2. Purchasing Departments/end user will ensure to Pre Dispatch inspection of stores through Inspection agency enlisted in the CSIDC Panel. 3. Purchasing Departments/end user will be responsible for ensuring the Quality of accepted stores. As per the Tech. Specification. 4. Purchasing Department/end user shall be ensure to execute the Integrity Pact between BUYER and BIDDER/ SUPPLIER in accordance with the letter vide No.799/eq-l- @2013 New Raipur Dated 10.07.2013 and 243/fo-@fu- @pkj@2013 New Raipur Dated 06.07.2013 issued by the Chief Secretary. Govt. of Chhattisgarh.

(Subas Chandra Bhagat) Incharge Marketing

Page 116: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

116/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/SSSI/7919 Dt.: 17-05-2017

Annexure-B CSIDC/MKD/TECH/2016-17/28

SPECIFICATION FOR WATER TANKER MOUNTED ON FOUR / TWO WHEEL TROLLEY

TSC 23-11-2016

(E) SPECIFICATION OF PRODUCTS

(A) TANKERS MOUNTED ON FOUR WHEEL TROLLEY (WITH 7.50 X 16 TYRE & TUBE) WITH LEAF SPRING OR WITHOUT LEAF SPRING

1. Chassis:

The Chassis shall be fabricated as per standard practice to mount the MS tank. All the joint shall be welded with gusset plates wherever required as per standard practice.

The Chassis frame shall have two longitudinal member and 5 cross members of channel

section of size 125 x 65 mm (ISMC) for 4500 & 5000 lts. Capacity. For 3500 lts. Capacity the chassis frame shall have two longitudinal members and 4 cross members of channel section of size 100 x 50 mm (ISMC) The overall approximate dimensions of various tanker trolley chassis shall be as under:- -----------------------------------------------------------------------------------------------------

S.No. Approx.Cap Length Width -----------------------------------------------------------------------------------------------------

1. 5000 liters 4 metres 1.00 mtr. 2. 4500 liters 4 meters 1.00 mtr. 3. 3500 liters 3.5 meters 1.00 mtr.

-----------------------------------------------------------------------------------------------------

2. Turn table:

The turn table frame shall be made out of 100x50mm (ISMC) MS channel with cross support, fixed with double rings fabricated from Angle Iron 40x40x6 mm and with 40mm diameter centre pin with suitable washer and locking arrangement.

3. Draw Bar:

Draw bar shall be in triangular construction made out of ISMC of size 100x50 mm with spring loaded eyehook made of 40mm dia MS bar.

The straight length of draw bar should be 150 cms including eye hook. Draw bar shall be hinged with the frame of turn table by 500 x 25mm Ms round bar having locking arrangement at both the end.

4. Axle & Brake assembly:

Axle shall be made from 63 x 63mm square bar with both the end machined, threaded and fitted with hubs and hexagonal lock nut, fitted with twin taper roller bearings, and provided with grease nipples for greasing the moving parts. For braking mechanical-internal expanding type brakes with suitable drums. hand operated, on rear wheels compete, with steel rod, clamps, springs and hand lever be provided.

(S.N. Chopra)

Incharge PS-III

Page 117: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

117/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/SSSI/7919 Dt.: 17-05-2017

5. Leaf Spring:

Four sets of leaf spring consisting of 13 leaves of size minimum 70 x 10mm, 1000mm long (distance between two pin) of alloy steel shall be provided. These leaf spring shall be fixed with frame by means of complete cast iron bracket assembly.

6. Tyres, tubes & wheel Assembly :

Four number tyre of 7.50 x 16 and tubes of standard make, Shall be provided with double plated rims 5mm thick with 5/6 nos. holes.

7. Water tanker:

The Water Tanker shall have capacity of 5000, 4500 & 3500 litres approx., and shall be manufactured in elliptical shape/ semi elliptical shape. The approx size of Water Tanker shall be as follows:- ----------------------------------------------------------------------------------------------------------- S. No. Approx. Major Axis Minor Axis Length ----------------------------------------------------------------------------------------------------------- 1. 5000 lit. 1.95 mtrs. 1.05 mtrs. 3.6 mtrs. 2. 4500 lit. 1.75 mtrs. 1.05 mtrs. 3.6 mtrs. 3. 3500 lit.. 1.5 mtrs 1.05 mtrs. 3.0 mtrs -----------------------------------------------------------------------------------------------------------

The tank shall be made out of 3.15mm thick MS sheet, and end plates of 4.0mm thick MS plate. End plate shall be maximum in two piece.

The tank shall be reinforced from inside by welding four numbers of elliptical rings made of 40 x 40 x 6mm MS angle one at both ends and two in between at suitable distance (total 04 on.) for 4500 & 5000 lts capacity. For 3500 lts capacity angle rings shall be provided at both ends and one at the middle (total 03 no.)

Two nos. baffle plate of 3.15mm thick MS sheet shall be provided in side the tank. These plates shall be properly welded with the central ring as per the standard practice. The height of baffle plate shall be 20cm. More than half of the height of tank. For 3500 lts capacity only one baffle plate be provided.

8. Manhole:

Two manhole with hinged cover shall be provided at the top of the tank. The cover of tank shall be fabricated from 3.15 thick MS sheet. The collar of the cover and manhole shall be made out of 4.00 mm MS strip. Locking arrangement for cover shall be provided; The manhole covers shall be such fabricated so that no foreign material may enter into the tank.

A 300 mm wide five steps ladder made of 32 x 32 x 2.5/3mm Ms angle be provided at left hand on rear side of the tanker (i.e. cleaner seat side). One no. 300 mm wide platform for full length at left hand be provided at appropriate level. The platform frame be made from Angle Iron 32 x 32 x2.5/3mm and 2.5 mm thick MS sheet. A suitable railing of 150 mm height on full length of platform shall be provided at the outer side of the platform by using 25x25x2.5/3mm Angle Iron or 25mm pipe and 2.0 mm MS sheet.

(S.N. Chopra) Incharge PS-III

Page 118: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

118/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/SSSI/7919 Dt.: 17-05-2017

The rear wheels shall be covered with mudguards fabricated out of 1.6mm thick MS sheets,

as per standard practice.

The Water Tanker shall be fixed on the chassis by 8 nos. suitable arranged fabricated shoes (box type brackets) from 5mm thick plates and base plate of approximate size 23x17 cms. and 12mm thick OR made of suitable ISMC bolted to the chassis with suitable ‘U’ clamps (two nos. in each base) The box brackets width shall not be less than 60mm and the bottom of the tank shall be provided with 6 mm thick and 120mm wide saddle plates for full width of the tank as a base for the shoes (box type brackets).

9. Ball Bering No. 31213 must be used. (B) TANKERS MOUNTED ON TWO WHEEL TROLLEY WITH LEAF SPRING OR

WITHOUT LEAF SPRING 1. Chassis:

The Chassis shall be fabricated as per standard practice to mount the MS tank. All the joint shall be welded with gusset plates wherever required as per standard practice.

The Chassis frame shall have two longitudinal member and 4 cross members of channel

section of size 100 x 50 mm (ISMC).

The overall approximate dimensions of various tanker trolley chassis shall be as under:- -----------------------------------------------------------------------------------------------------

S.No. Approx.Cap Length Width -----------------------------------------------------------------------------------------------------

1. 3500 liters 3.0 metres 0.80 mtr. 2. 2500 liters 2.5 meters 0.80 mtr.

----------------------------------------------------------------------------------------------------- 2. Draw bar:

Draw bar shall be in triangular construction made out of MS channel of size 100 x 50 mm with spring loaded eyehook made of 40 mm dia MS bar.

The straight length of draw bar should be 150 cms including eye hook.

3. Axle & Brake assembly:

Axle shall be made from 63 x 63mm square bar with both the end machined and threaded and provided with iron hubs and hexagonal lock nut, fitted with twin taper roller bearings and provided with grease nipples for greasing the moving parts.

4. Leaf spring:

Two sets of leaf spring consisting of 13 leaves of size 70 x 10mm minimum 1000 mm long (distance between two pin) of alloy steel shall be provided. These leaf spring shall be fixed with frame by means of complete cast iron bracket assembly.

5. Tyres, tubes & wheel Assembly:

(S.N. Chopra)

Incharge PS-III

Page 119: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

119/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/SSSI/7919 Dt.: 17-05-2017

Two number tyres of 7.50 x 16 and tubes of standard make shall be provided with double plated rims 5 mm thick with 5/6 nos. holes for 2500 lts. Capacity tanker. For 3500 lts. Capacity two number tyres of 9x16 and tubes of standard make shall be provided.

6. Water Tanker:

The Water Tanker Should have capacity of 2500 & 3500 liters approx. Manufactured in elliptical. Shape. The approx. size of Water Tanker are as follows :-

-------------------------------------------------------------------------------------------------------------- S.No. Approx.Cap Major Axis Minor Axis Length -------------------------------------------------------------------------------------------------------------- 1. 3500 liters 1.5 mtrs 1.05 mtrs 3.0 mtrs. 2. 2500 liters 1.20 mtrs 1.05 mtrs 2.5 mtrs. --------------------------------------------------------------------------------------------------------------

The tank shall be made out of 3.15 mm thick MS sheet, and end plates of 4.0 thick MS plate. End plate should be maximum two pieces.

The tank shall be reinforced from inside by welding three numbers of elliptical rings made of 40 x 40 x 6mm MS angle one at both ends and one in between at suitable distance.

One baffle plate of 3.15mm shall be provided inside the tank. These plates shall be properly welded with the central ring as per the standard practice. The height of baffle plate shall be 20 cm more than half of the height of tank.

7. Manhole:

One manhole with hinged cover shall be provided at the top of the tank. The cover of tank shall be fabricated from 3.15 thick MS sheet. The collar of the cover and manhole shall be made out of 4.00 mm MS strip. Locking arrangement for cover shall also be provided; The manhole cover shall be such fabricated so that no foreign material may enter in to the tank.

A 300 mm wide three steps ladder made of 32x32x2.5/3mm MS angle be provided at left hand on front side of the tanker (i.e. cleaner seat side). One no. 300mm wide platform for full length at left hand be provided at appropriate level. The platform frame be made from angle iron 32x32x2.5/3mm and 2.5 mm thick MS sheet. A suitable railing of 150mm height on full length of platform shall be provided at the outer side of the platform by using 25x25x3mm Angle Iron of 25mm pipe and 2.0mm MS Sheet.

The water tanker shall be fixed on the chassis by 6 nos. suitable arranged fabricated shoes (box type brackets) from 5mm thick plates and base plate of approximate size 23 x 17 cms. and 12 mm thick OR made of suitable ISMC bolted to the chassis with suitable ‘U’ clamps (two nos. in each base). The box brackets width shall not be less than 60 mm and the bottom of the tank shall be provided with 6 mm thick and 120 mm wide saddle plates for full width of the tank as a base for the shoes (box type brackets.)

8. Ball Bering No. 31213 must be used.

(C) TANKERS MOUNTED ON FOUR WHEEL TROLLEY: (WITH 9X20 TYRES TUBES)

1. Chassis: The Chassis shall be fabricated as per standard practice to mount the MS tank. All the joint

shall be welded with gusset plates wherever required as per standard practice.

(S.N. Chopra)

Incharge PS-III

Page 120: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

120/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/SSSI/7919 Dt.: 17-05-2017

The chassis frame shall have two longitudinal member and 3 cross members of channel section of size 150x75mm (ISMC) for 4000 & 5000 It. Capacity.

The width of the chassis frame shall be of 1.0mt and length shall be equal to the length of the tank.

2. Turn table:

The turn table frame shall be made out of 100x50mm (ISMC or equivalent) MS channel with cross support, fixed with double rings fabricated out of Angle Iron 40x40x6 mm and with 40mm diameter centre pin with suitable washer and locking arrangement.

3. Draw Bar:

Draw bar shall be in triangular construction made out of Ms Channel of size 100x50 mm with spring loaded eyehook made of 40mm dia MS bar.

The straight length of draw bar should be 150 cms including eye hook. Draw bar shall be hinged with the frame of turn table by 100x25mm MS round bar having locking arrangement at both the end.

4. Axle & Brake assembly:

Axle shall be made from 63x63mm square bar of 1750mm length with both the end machined and threaded and provided with iron hubs and hexagonal lock nut, fitted with twin taper roller bearings, and provided with grease nipples for greasing the moving parts. For braking mechanical-internal expanding type brakes with suitable drums, hand operated, on rear wheels compete, with steel rod, clamps, springs and hand lever be provided.

5. Leaf Spring:

Four sets of leaf spring consisting of 13 leaves of size 70x11 mm minimum 1000mm long (distance between two pin) of alloy steel shall be provided. These leaf spring shall be fixed with frame by means of complete cast iron bracket assembly.

6. Tyres, tubes & wheel Assembly :

Four number tyre of 9 x 20 and tubes of standard make. Shall be provided with double plated rims 5 mm thick with 5/6 nos. holes. For four wheel trolley.

7. Water tanker:

The Water Tanker shall have capacity of 5000 & 4000 litres approx. manufactured in semi elliptical shape.

The minor axis of the tank shall be of 1.05 mtr. The manufacturer shall design major axis

and length of the semi elliptical tank accordingly. The tank shall be made out of 3.15 mm thick MS sheet, and end plates of 4.0 thick MS plate.

End plate should be maximum two pieces.

(S.N. Chopra)

Incharge PS-III

Page 121: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

121/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/SSSI/7919 Dt.: 17-05-2017

The tank shall be reinforced from inside by welding three numbers of elliptical rings made of 40 x 40 x 6mm MS angle one at both ends and one in between at suitable distance.

Two baffle plate of 3.15mm shall be provided in side the tank. These plates shall be properly

welded with the central ring as per the standard practice. The height of baffle plate shall be 20 cm more than half of the height of tank.

8. Manhole:

Two manhole with hinged cover shall be provided at the top of the tank. The cover of tank shall be fabricated from 3.15 thick MS sheet. The collar of the cover and manhole shall be made out of 4.00 mm MS strip. Locking arrangement for cover shall also be provided; The manhole cover shall be such fabricated so that no foreign material may enter in to the tank.

A 300 mm wide three steps ladder made of 30x30x3mm MS angle be provided at left hand

on front side of the tanker. One no. 300mm wide platform for full length at left hand be provided at appropriate level. The platform frame be made from angle iron 35x35x3mm and 2.5 mm thick MS sheet. A suitable railing of 150mm height on full length of platform shall be provided at the outer side of the platform by using 25x25x3mm Angle Iron of 25mm pipe and 2.0mm MS Sheet.

The water tanker shall be fixed on the chassis by 8 nos. suitable arranged fabricated shoes

(box type brackets) from 5mm thick plates and base plate of approximate size 23 x 17 cms. and 12mm thick bolted to the chassis or made of 100x50mm channel properly covered with sheet of 3.15mm suitable ‘U’ clamps (two nos. in each base). The box brackets width shall not be less than 60 mm and the bottom of the tank shall be provided with 6 mm thick and 120 mm wide saddle plates for full width of the tank as a base for the shoes (box type brackets.)

9. Ball Bering No. –31213 must be used. (D) TANKERS MOUNTED ON TWO WHEEL TROLLEY WITH LEAF SPRING OF

WITHOUT LEAF SPRING: 1. Chassis:

The Chassis shall be fabricated as per standard practice to mount the MS tank. All the joint shall be welded with gusset plates wherever required as per standard practice.

The Chassis frame shall have two longitudinal members and 4 cross members of channel

section of size 150 x 75 mm (ISMC) The overall approximate dimensions of various tanker trolley chassis shall be as under:- -----------------------------------------------------------------------------------------------------

S.No. Approx.Cap Length Width -----------------------------------------------------------------------------------------------------

1. 4000 liters 3.3 metres 1.2 mtr. 2. 4500 liters 3.5 meters 1.2 mtr. 3. 5000 liters 3.5 meters 1.2 mtr. 4. 5500 liters 3.7 metres 1.2 mtr.

-----------------------------------------------------------------------------------------------------

(S.N. Chopra) Incharge PS-III

Page 122: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

122/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/SSSI/7919 Dt.: 17-05-2017 WATER TANKERS MOUNTED ON FOUR/TWO WHEEL TROLLEY 2. Draw Bar:

Draw bar shall be in triangular construction made out of MS channel of size 150x75 mm with spring loaded eyehook made of 40mm dia MS bar.

The minimum straight length of draw bar should be 150 cms including eye hook.

3. Axle & Brake assembly:

Axle shall be made from 72 x 72mm square bar with both the end machined and threaded and provided with iron hubs and hexagonal lock nut, fitted with twin taper roller bearings and provided with grease nipples for greasing the moving parts.

4. Leaf Spring:

Two sets of leaf spring consisting of 13 leaves of 4000 & 4500 Ltr. And 19 leaves for 5000 & 5500 ltr. Cap. Of size minimum 70 x 10mm minimum 900mm long (distance between two pin) of alloy steel shall be provided. These leaf spring shall be fixed with frame by means of complete cast iron bracket assembly.

5. Tyres, tubes & wheel Assembly :

Two number tyre of 9 x16 / 9x16 and tubes of standard make Shall be provided with double plated rims 5mm thick with 8 nos. holes.

6. Water tanker:

The Water Tanker should have capacity of 5000, 5500 litres approx. manufactured in elliptical shape. The approx size of Water Tanker are as follows:- ----------------------------------------------------------------------------------------------------------- S. No. Approx. Major Axis Minor Axis Length ----------------------------------------------------------------------------------------------------------- 1. 4000 lit. 1.65 meters 1.11 mtrs. 2.8 mtrs. 2. 4500 lit. 1.70 meters 1.13 mtrs. 3.0 mtrs. 3. 5000 lit. 1.80 meters 1.18 mtrs. 3.0 mtrs 4. 5500 lit. 1.80 meters 1.22 mtrs. 3.2 mtrs. -----------------------------------------------------------------------------------------------------------

WATER TANKERS MOUNTED ON FOUR/TWO WHEEL TROLLEY

The tank shall be made out of 3.15mm thick MS sheet, and end plates of 4.0mm thick MS plate. End plate should be in maximum two pieces.

The tank shall be reinforced form inside by welding three numbers of elliptical rings made of

40x40x6mm MS Angle one at both ends and one in between at suitable distance.

One baffle plate of 3.15mm shall be provided in side the tank. These plates shall be properly welded with the central ring as per the standard practice. The height of baffle plate shall be 20cm. more than half of the minor axis of tank.

(S.N. Chopra)

Incharge PS-III

Page 123: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

123/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/SSSI/7919 Dt.: 17-05-2017 7. Manhole:

One manhole with hinged cover shall be provided at the top of the tank. The cover of tank shall be fabricated from 3.15 thick MS sheet. The collar of the cover and manhole shall be made out of 4.00 mm MS strip. Locking arrangement for cover shall also be provided; The manhole cover shall be such fabricated so that no foreign material may enter in to the tank.

A 300 mm wide three steps ladder made of 32x32x2.5/3mm MS angle be provided at

left hand on front side of the tanker (i.e. cleaner seat side). One no. 300mm wide platform for full length at left hand be provided at appropriate level. The platform frame be made from angle iron 32x32x2.5/3mm and 2.5 mm thick MS sheet. A suitable railing of 150mm height on full length of platform shall be provided at the outer side of the platform by using 25x25x3mm Angle Iron of 25mm pipe and 2.0mm MS Sheet.

The water tanker shall be fixed on the chassis by 6 nos. suitable arranged fabricated shoes (box type brackets) from 5mm thick plates and base plate of approximate size 23 x 17 cms. and 12 mm thick OR made of suitable ISMC bolted to the chassis with suitable ‘U’ clamps (two nos. in each base). The box brackets width shall not be less than 60 mm and the bottom of the tank shall be provided with 6 mm thick and 120 mm wide saddle plates for full width of the tank as a base for the shoes (box type brackets.)

Pump set stand shall be provided at rear side of the tank.

8. Ball Bering No. 31213 must be used.

WATER TANKERS MOUNTED ON FOUR/TWO WHEEL TROLLEY

1. Outlet:

Outlet 75 mm NB class ‘A’ GI nipple of 10 length (minimum) be provided at the rear of the tank along with required 75 mm GM full way wheel valve, followed by another 20 cm length nipple for connecting a hose pipe. A Drain plug of 50 mm shall be provided at the bottom of the tank at suitable place.

2. Accessories:

The water tanker shall be provided with 2 nos. of reflectors, number plate and tool box etc. The size of tool box should be 600 mm (L) x 300 mm (W) x 300 mm (H) made of 2.5 mm MS sheet.

3. Painting & Finishing:

The tanker should be spray painted, with printing coat of red-oxide and two coat of synthetic enamel paint and color as desired by consignee. Interior of the tank should be painted with two coat of suitable primer followed by Non-poisonous white rubber paint.

4. Guarantee:-

The manufacturer shall furnish guarantee for one year against manufacturing defects leakage etc., along with tenders incorporating that in case of complaint they shall undertake satisfactory repairs within 10 days free of cast.

(S.N. Chopra) Incharge PS-III

Page 124: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

124/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/SSSI/7919 Dt.: 17-05-2017

5. Inspection:-

The inspection of water tanker shall be carried out by of CSIDC, Ltd. Approved Inspection Agencies

6. Ball Bering No. 31213 must be used.

Note:- If required minor deviation/amendment in specification may be done, after taking approval from CSIDC, Ltd,.

Recommended by Technical Specification Committee Dated 23-11-2016

(S.N. Chopra)

Incharge PS-III

Page 125: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

125/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/SSSI/7919 Dt.: 17-05-2017

SCHEDULE ‘B’

(SPECIAL CONDITION OF CONTRACT) ISI Pressure Cooker

Rate Contract Will be governed by the Terms & Conditions laid down in the

CSIDC FORM NO. 1 & 2

(Subas Chandra Bhagat) Incharge Marketing

Page 126: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

126/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/SSSI/7919 Dt.: 17-05-2017

SCHEDULE “C”

LIST OF PARALLEL RATE CONTRACT FOR ITEM- Water Tanker

(Subas Chandra Bhagat) Incharge Marketing

S.No. Name of Tenderers Valid Up to Rate Contract No.

1. M/s Agrahari Agrotech Industries, Village-Bori, Tah & Dist.- Rajnandgaon Mob-9753072555

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/AAI/7915

2. M/s G.V. Industries, 22 A, Industrial Area, Dhar-454001 (M.P.) Mob-9425046639, 9826469388

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/G.V.I/7916

3. M/s National Engineering Works, Opp. Sirpur Lake Indore Ahmedabad Road, Indore (M.P.), Mob-07000233648

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/NEW/7920

4. M/s Netam Engineering Works, Audhogik Area, Bhakhara Road, Villa-Arjuni, Dhamtari, Mob-9406021763, 8602729134

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/NEW/7921

5. M/s New Malwa Agro & Fabricators, Plot No.-59, Sec-C, Sirgitti, Industrial Area, Bilaspur, Mob-9425046639, 7772086742

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/NMA&F/7922

6. M/s Rahul Enterprises, Office- 1016, Roshan Gagh, Pushpa Nagar Road, Esh Bagh (M.P.) Mob.-9826469388, 9826038441

12-04-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/RE/7923

7. M/s Shri Sai Steel Industries, Industrial.Area Nainpur, Surajpur, Distt.-Surajpur (C.G.) -497229 Mob.-9826649514 Email- [email protected]

17-05-2017 to

11-04-2018

Rate Contract No. CSIDC/MKD/ 16-17/143/12768/WT/SSSI/7919

Page 127: Chhattisgarh State Industrial Development Corporation Limited Water Tanker.pdf · 1/127 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh

127/127 Rate Contract No. CSIDC/MKD/16-17/143/12768/WT/SSSI/7919 Dt.: 17-05-2017

SCHEDULE – “D”

FORMAT FOR QUATERLY DRAWAL REPORT Name of the Firm __________________ I- Jan-Mar Report No. __________________ II- Apr-June Rate Contract No. __________________ III- July-Sept. Date of Submission __________________ IV- Oct - Dec Total Position of Order against Rate Contract till the submission of Report. S.No. Name of

Department Quantity and Value of Orders Received (Rs.)

Quantity and Value of Orders Executed (Rs.)

Balance Quantity and Value to be Supplied (Rs.)

Reasons

Foot 1. Value indicate should be a) Value of orders received during the quarter-Rs.

Total value inclusive of all Taxes duties and incidental b) Value of orders supplied during the quarter-Rs. Charges

2. Nil report should also be Submitted.

(Subas Chandra Bhagat) Incharge Marketing