DQD 507 Rev. 2012-05-22 Page 1

Certificate of Compliance Certificate: 70047714 (225996) Master Contract: 225996

Project: 70091002 Date Issued: 2016-12-02

Issued to: SpectraSensors, Inc.

11027 Arrow Route

Rancho Cucamonga, California 91730

USA

Attention: Paul Silva

The products listed below are eligible to bear the CSA Mark shown

with adjacent indicators 'C' and 'US' for Canada and US or with adjacent

indicator 'US' for US only or without either indicator for Canada only.

Issued by: Sorin Tat

Sorin Tat

PRODUCTS

CLASS - C225882 - PROCESS CONTROL EQUIPMENT-For Hazardous Locations - Certified to US

Standards

CLASS - C225802 - PROCESS CONTROL EQUIPMENT-For Hazardous Locations-

Class I, Division 2, Groups A, B, C and D, T4, Type 4X;

Oxygen Analyzer, Model OXY5500.

Rated at 120Vac 115mA or at 240Vac 91mA, 50/60Hz or at 9-30Vdc, 0.5A max. For use in an ambient

temperature range of: -20C to +60C.

Relay contact ratings for external connection: L-S1 and L-S2 with the following rating specifications: 250mA,

Maximum peakVoltage= 400V.

Note:

- Interconnection of the Analyzer enclosure shall be accomplished using wiring methods approved for Class I,

Division 2 hazardous locations as per the Canadian Electrical Code (CEC) Appendix J and the National Electrical

Code (NEC) Article 501.

Certificate: 70047714

Project: 70091002

Master Contract: 225996

Date Issued: 2016-12-02

DQD 507 Rev. 2012-05-22 Page 2

APPLICABLE REQUIREMENTS

CAN/CSA C22.2 No. 0-10 General Requirements – Canadian Electrical Code, Part II CSA C22.2 No.94.2-15/UL50E Enclosures for electrical equipment, environmental considerations

CAN/CSA C22.2 No. 213-M1987 Non-Incendive Electrical Equipment for Use in Class I, Division 2

Hazardous Locations

CAN/CSA 61010-1-12 Safety Requirements for Electrical Equipment for Measurement, Control and

Laboratory Use - Part 1: General Requirements - Third Edition

ANSI/UL 61010-1 Safety Requirements for Electrical Equipment for Measurement, Control and

Laboratory Use - Part 1: General Requirements - Third Edition

CAN/CSA C22.2 No. 60529:05 Degrees of protection provided by enclosures (IP Code)

ANSI/ISA 12.12.01 - 2011 Non-Incendive Electrical Equipment for Use in Class I and II, Division 2,

Class III Divisions 1 and 2 Hazardous (Classified) Locations

ANSI/IEC 60529 - 2004 Degrees of protection provided by enclosures (IP Code)

DQD 507 Rev. 2012-05-22 Page 1

Supplement to Certificate of Compliance

Certificate: 70047714 (225996) Master Contract: 225996

The products listed, including the latest revision described below,

are eligible to be marked in accordance with the referenced Certificate.

Product Certification History

Project Date Description

70091002 2016-12-02 Update report 70047714 in order to add a new gasket and to update the

electrical ratings for DC supply to: 9 - 30Vdc, 0.5A max.

70047714 2016-02-22 Original certification for Class I Div.2 of OXY5500.

ATTESTATION D’EXAMEN DE TYPE

TYPE EXAMINATION CERTIFICATE

Seul le texte en français peut engager la responsabilité du LCIE. Ce document ne peut être reproduit que dans son intégralité, sans aucune modification. Il est établi en accord avec le référentiel de certification ATEX du LCIE. The LCIE’s liability applies only on the French text. This document may only be reproduced in its entirety and without any change. It is issued in accordance with LCIE’s ATEX Certification Rules.

CERT-ATEX-FORM 05 Rev. 02 Page 1 of 3

1 Version : 01 LCIE 16 ATEX 1012 X Issue : 01

Directive 2014/34/UE Directive 2014/34/EU

2 Appareil ou Système de Protection destiné à être utilisé en Atmosphères Explosibles

Equipment or Protective System Intended for use in Potentially Explosive Atmospheres

3 Produit : Product : Analyseur d’oxygène Oxygen Analyzer

Type: OXY5500

4 Fabricant : Manufacturer :

SpectraSensors Inc.

5 Adresse : Address :

11027 Arrow Route Rancho Cucamonga, CA 91730

Etats-Unis

6 Ce produit et ses variantes éventuelles acceptées sont décrits dans I'annexe de la présente attestation et dans les documents descriptifs cités en référence.

This product any acceptable variation thereto is specified in the schedule to this certificate and the documents therein referred to.

7 Le LCIE certifie que ce produit est conforme aux Exigences Essentielles de Sécurité et de Santé pour la conception et la construction de produits destinés à être utilisés en atmosphères explosibles, données dans l’annexe II de la Directive.

LCIE certifies that product has been found to comply with the Essential Health and Safety Requirements relating to the design and construction of products intended for use in potentially explosive atmospheres, given in Annex II to the Directive.

Les résultats des vérifications et essais figurent dans le(s) rapport(s) confidentiel(s) N° :

The examination and test results are recorded in confidential report(s) N°:

13670-674713 ; 144638-693583

8 Le respect des Exigences Essentielles de Sécurité et de Santé est assuré par la conformité à :

Compliance with the Essential Health and Safety Requirements has been assured by compliance with :

EN 60079-0:2012 + A11:2013 ; EN 60079-15:2010

9 Le signe « X » lorsqu'il est placé à la suite du numéro de l’attestation, indique que cet appareil est soumis aux conditions particulières d’utilisation, mentionnées dans l’annexe de cette attestation.

If the sign “X” is placed after the certificate number, it indicates that the product is subject to the Specific Conditions of Use specified in the schedule to this certificate.

10 Cette Attestation d'Examen de Type concerne uniquement la conception et la construction du produit spécifié.

This Type Examination Certificate relates only to the design and construction of the specified product.

Des exigences supplémentaires de la directive sont applicables pour la fabrication et la fourniture du produit. Ces dernières ne sont pas couvertes par la présente attestation.

Further requirements of the Directive apply to the manufacturing process and supply of this product. These are not covered by this certificate.

11 Le marquage du produit est mentionné dans l’annexe de cette attestation.

The marking of the product is specified in the schedule to this certificate.

Fontenay-aux-Roses, le 22 septembre 2017 Responsable de Certification Certification Officer

Julien Gauthier

ATTESTATION D’EXAMEN DE TYPE - ANNEXE

TYPE EXAMINATION CERTIFICATE - SCHEDULE

Seul le texte en français peut engager la responsabilité du LCIE. Ce document ne peut être reproduit que dans son intégralité, sans aucune modification. Il est établi en accord avec le référentiel de certification ATEX du LCIE. The LCIE’s liability applies only on the French text. This document may only be reproduced in

its entirety and without any change. It is issued in accordance with LCIE’s ATEX Certification Rules.

CERT-ATEX-FORM 05 Rev. 02 Page 2 of 3

1 Version : 01 LCIE 16 ATEX 1012 X Issue : 01

12 DESCRIPTION DU PRODUIT DESCRIPTION OF PRODUCT

Cet analyseur est un dispositif qui permet la mesure de l’oxygène dans le gaz naturel via un capteur d’oxygène inséré dans le process. De plus, une sonde PT100 peut être aussi connectée. Un capteur de pression peut être installé en option. L’équipement se compose de deux enveloppes imbriquées l’une dans l’autre. L’enveloppe intérieure contient l’électronique I/O nécessaire et des ports de communication. Elle est montée via un rail dans la seconde enveloppe qui contient le reste des modules. Le couvercle de l’analyseur possède une fenêtre pour l’écran d’affichage du transmetteur et un clavier. L’analyseur peut être alimenté en AC/DC ou DC/DC.

This analyzer is a device which allows the measurement of oxygen in natural gas using a flow oxygen sensor which is inserted into the process stream. In addition to the probe, there is a PT-100 4-wire temperature sensor connected to the controller. A pressure transducer is offer as an option. The equipment consists of two enclosures which are nested into each other. The inner enclosure houses the necessary transmitter electronic I/O ports and communication ports. This inner enclosure is mounted via cap rail to the outer enclosure which includes all modules. The cover of the analyzer has a window for the transmitter screen display and a foil keyboard. The analyzer can be supplied in AC/DC or DC/DC.

DETAIL DE LA GAMME RANGE DETAILS

N/A N/A

MARQUAGE MARKING

Le marquage du produit doit comprendre : The marking of the product shall include the following :

SpectraSensors Inc. ou sa marque commerciale déposée Adresse : … Type : OXY5500 N° de fabrication : … Année de fabrication : …

II 3 G

Ex nA IIC T3 Gc IP64 LCIE 16 ATEX 1012 X -20°C ≤ Tamb ≤ +60°C AVERTISSEMENT – NE PAS OUVRIR SI UNE ATMOSPHERE EXPLOSIVE PEUT ETRE PRESENTE.

SpectraSensors Inc. or its trademark Address: … Type : OXY5500 Serial number : … Year of construction : …

II 3 G

Ex nA IIC T3 Gc IP64 LCIE 16 ATEX 1012 X -20°C ≤ Tamb ≤ +60°C WARNING – DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE MAY BE PRESENT.

L’appareil doit également comporter le marquage normalement prévu par les normes de construction qui le concernent sous la responsabilité du fabricant.

The equipment shall also bear the usual marking required by the product standards applying to such equipment under the manufacturer responsibility.

13 CONDITIONS PARTICULIERES D'UTILISATION SPECIFIC CONDITIONS OF USE

a. L'installation électrique à laquelle est connecté l'équipement doit être protégée contre les transitoires. Le dispositif de protection doit être réglé à un niveau n'excédant pas 140% de la tension assignée de crête aux bornes de l'alimentation du matériel (conformément au paragraphe 13.c de la norme EN 60079-15).

The electrical installation to which the apparatus is connected must be protected against transients. The protective device has to be set at a level not exceeding 140% of the peak rated voltage values at the power supply terminals (according to clause 13.c) of standard EN 60079-15).

b. Risque potentiel de charges électrostatiques, voir instruction. Potential static electrostatic hazard, see instruction.

14 EXIGENCES ESSENTIELLES DE SANTE ET DE SECURITE ESSENTIAL HEALTH AND SAFETY REQUIREMENTS

Couvertes par les normes listées au point 8. Covered by standards listed at 8.

15 DOCUMENTS DESCRIPTIFS DESCRIPTIVE DOCUMENTS

N° Description Reference Rev. Date Page(s)

1. Technical file 8300002033 B 2017/04/25 121

ATTESTATION D’EXAMEN DE TYPE - ANNEXE

TYPE EXAMINATION CERTIFICATE - SCHEDULE

Seul le texte en français peut engager la responsabilité du LCIE. Ce document ne peut être reproduit que dans son intégralité, sans aucune modification. Il est établi en accord avec le référentiel de certification ATEX du LCIE. The LCIE’s liability applies only on the French text. This document may only be reproduced in

its entirety and without any change. It is issued in accordance with LCIE’s ATEX Certification Rules.

CERT-ATEX-FORM 05 Rev. 02 Page 3 of 3

1 Version : 01 LCIE 16 ATEX 1012 X Issue : 01

16 INFORMATIONS COMPLEMENTAIRES ADDITIONAL INFORMATIONS

Essais individuels Routine tests

Conformément au paragraphe 23.2.1 de la norme EN 60079-15, chaque exemplaire de l’équipement doit être soumis à un essai de rigidité diélectrique (effectué selon le paragraphe 6.5.1).

According to clause 23.2.1 of standard EN 60079-15, each apparatus shall be submitted to a dielectric strength test (carried out in accordance with clause 6.5.1).

Paramètres

Ratings

18-30 V DC ou 80-253 V AC 18-30 V DC or 80-253 V AC

Produits considérés conformes à la Directive 2014/34/UE

(conformément à l’Article 14 de la Directive 2014/34/UE) Product regarded as conforming to Directive 2014/34/EU

(in accordance with Article 14 of Directive 2014/34/EU) Les équipements certifiés suivants peuvent être intégrés :

The following certified equipment can be integrated :

Désignation du produit Designation of product

Fabricant Manufacturer

Type Type

Document de référence Document of reference

Transmetteur de pression Pressure transmitter

GP:50 311.N LCIE 08 ATEX 6132 X

Alimentation AC AC power supply

SIEMENS 6EP1331-ISH03 EPS 08 ATEX 1101 X

Accessoires d’entrée Entry accessories

CMP 737, 747, 757, 767, 797 SIRA 13 ATEX 1265 X

Entrée de câble Cable gland

HUMMEL HSK-MZ-EMV KEMA 99 ATEX 6971 X

Ces produits sont déclarés conformes par leurs fabricants et

leur conformité ne relève pas de la responsabilité du LCIE. These products are declared compliant by their manufacturers

and their conformity does not fall under the responsibility of LCIE.

17 DETAILS DES MODIFICATIONS DETAILS OF CHANGES

Version 00 : 2016/06/15 Version 01

Version initiale selon les normes : - EN 60079-0:2012 + A11:2013, - EN 60079-15:2010. Suppression du respirateur REDAPT du design. Changement du joint du couvercle. Modification du degré de protection d’IP65 à IP64.

Issue 00 : 2016/06/15 Issue 01

Initial issue according to standards - EN 60079-0:2012 + A11:2013, - EN 60079-15:2010. Deletion of the REDAPT breather from the design Change of the gasket of the cover Modification from IP65 to IP64

2017-09-22

Annex 01 to Certificate IECEx LCIE 16.0009X issue 01

Page 1 of 2

This Annex is valid only in combination with certificate mentioned above and may only be reproduced in its entirety and without any change. CERT-ATEX-FORM 14 Rev. 01

FULL EQUIPMENT DESCRIPTION

The analyser OXY5500 is a device which allows the measurement of oxygen in natural gas using a flow through fiber optic(*1) oxygen sensor, which is inserted into the process stream. In addition to the probe, there is a PT-100 4-wire temperature sensor connected to the controller. A pressure transducer is offer as an option and its measurement is fed back into the controller for pressure compensation and better accuracy of oxygen measurement.

The equipment consists of two enclosures which are nested into each other.

The inner enclosure houses the necessary transmitter electronic I/O ports and communication ports. This inner enclosure is mounted via cap rail to the outer enclosure which includes all modules.

The analyser can be supplied by :

- AC voltage via an AC/DC power supply SIEMENS, type 6EP1331-ISH03 (Ex nA IIC T3 Gc)

- Or DC voltage via a DC/DC power supply XP Power, type DDC15

The cover of the analyzer has a window for the transmitter screen display and a foil keyboard.

Products integrated into the equipment :

Equipment Manufacturer Type Marking COC Standards

Pressure transmitter

GP:50 311.N Ex nA IIC T5

-40°C=+80°C

IECEx LCI 08.0056 X IEC 60079-0 Ed.4 IEC 60079-15 Ed.3 (*2)

AC power supply

SIEMENS 6EP1331-

ISH03 --

Assessed during initial issue

/

Entry accessories

CMP 737, 747, 757, 767,

797 Ex e IIC Gb IECEx SIR13.0094 X

IEC 60079-0 Ed.6.0 IEC 60079-7 Ed.4

Cable gland HUMMEL HSK-MZ-

EMV Ex e IIC Gb IECEx KEM 07.0014X

IEC 60079-0 Ed.6.0 IEC 60079-7 Ed.4

Note: The Breather REDAPT is no longer used in the OXY5500 (refer to the Drawing EX0800000019 Rev E) compared to the initial issue. (*1) A fiber-optic probe is included to the analyser. This one is installed inside a conduit and is conform to the industrial standards. Therefore, according to ISH1 of standard IEC 60079-28, it is exempted of assessment according to IEC 60079-28 standard.

(*2) Because standards do not have the same edition, the comparison between the different editions were assessed during initial issue.

MARKING

SpectraSensors Inc. or its registered trademark Address : = Type : OXY5500 Serial number : = Year of construction : = Ex nA IIC T3 Gc IP64 IECEx LCIE 16.0009 X -20°C Tamb +60°C WARNING – DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE MAY BE PRESENT.

RANGE DETAILS

N/A

RATINGS

18-30 V DC or 80-253 V AC

Annex 01 to Certificate IECEx LCIE 16.0009X issue 01

Page 2 of 2

This Annex is valid only in combination with certificate mentioned above and may only be reproduced in its entirety and without any change. CERT-ATEX-FORM 14 Rev. 01

FULL CONDITIONS OF CERTIFICATION (ou FULL SCHEDULE OF LIMITATIONS)

a. The electrical installation to which the apparatus is connected must be protected against transients. The protective device has to be set at a level not exceeding 140% of the peak rated voltage values at the power supply terminals (according to clause 13.c) of standard IEC 60079-15). b. Potential static electrostatic hazard, see instruction.

ROUTINE TESTS

According to clause 23.2.1 of standard IEC 60079-15, each apparatus shall be submitted to a dielectric strength test (carried out in accordance with clause 6.5.1).

APPARATUS OVERVIEW

ADDITIONAL MANUFACTURING LOCATIONS

N/A