caterpillar machine price list wt-mwl medium …

CATERPILLAR MACHINE PRICE LIST

WT-MWL

MEDIUM WHEEL LOADER WORK TOOLS Ship Weight List Price

lbs At Factory

Standard Equipment:

This WT-MWL Price List consists ofWork Tools for 950 through 982 MediumWheel Loaders

Listed below are the Machines andproducts for each machine group.The search for Machine sectionscopy the header below and pasteinto the search barSnow Removal Products for Medium

950 GC WHEEL LOADER-Buckets-Coupler-Blades-Snow Products

950 & 962 WHEEL LOADER-Buckets-Coupler-Forks-Blades-Material Handling Arm-Rakes-Snow Products

966 & 972 WHEEL LOADER-Buckets-Coupler-Forks-Material Handling Arm-Rakes-Blades-Snow Products

980H, 980K, 980L AND 980M WHEEL LOADER-Buckets-Coupler-Forks-Blades-Snow Product-Block Handling Tools

982M WHEEL LOADER-Buckets

Cat Snow Blades for Wheel Loaders- Key Features (GEHQ0237)Cat V-Plows for Wheel Loaders- Key Features (GEHQ0238)Cat Snow Push for Wheel Loaders- Key Features (GEHQ0239)Cat Ice Scarifiers for Wheel Loaders- Key Features (GEHQ0240)

Supersedes 09FEB2021 Subject to change without notice Effective 20FEB2021Printed in USACaterpillar: Confidential Green

US-A D U. S. DOLLAR CURRENCY WT-MWL-001

Caterpillar -2021 Price ListEducational Services Commission of New Jersey

NJ State Approved Co-op #65MCESCCPS Grounds Equipment - Bid #ESCNJ 18/19-25

Bid Term: 2/22/19 - 2/21/21; Extended to 2/21/22


WT-MWL


lbs At Factory

Wheel Loaders have updated bucketnomenclature to include key attributes:Arrangement or not, Bucket type,duty (durability), bucket width,capacity and interface to the carrier.Details can be found in MarketingBulletin TEJB9847.







WT-MWL


lbs At Factory

0P-4739 MEDIUM WHEEL LOADER WORK TOOLS 0 NC.........................

PLEASE USE THE 0P REFERENCE NUMBER LISTED ABOVE WHEN ORDERING.

FOR QUESTIONS, SUPPORT AND QUOTATIONSPLEASE CONTACT THE SALES SUPPORT TEAM INAMERICAS NORTH VIA EMAIL AT [email protected]

0P-0210Please use this packing code to orders from this Price List.







WT-MWL


lbs At Factory

TECHNOLOGY PRODUCTS

CAT PAYLOAD - WEIGHING SYSTEM

NOTE: Refer to KITS-MWL pricelist to order dealer installedkit for CAT PAYLOAD for GC, H-Series, and K-Series.Refer to SIS serial number prefix C55 forinstallation and calibration instructions.







WT-MWL

REF Ship Weight List Price

USE NO. lbs At FactoryCATERPILLAR WORK TOOLS

950 GC WHEEL LOADER

950GC BUCKETS / PIN ON

GC-TYPE GENERAL PURPOSE PERFORMANCE SERIES (PIN-ON)

W 448-5092 BKT GP GC 114" 4.00YD3 PO 3,243 $11,549 NI.........................

GC-TYPE PERFORMANCE SERIES BUCKETFOR USE WITH: 950GC Machines ONLYREQUIRES: G.E.T.CAPACITIES:3.75 YD3 (2.9 M3) w/bolt-on adapters, 117" (2972mm) wide4.00 YD3 (3.1 M3) w/bolt-on adapters and segments, 114" (2894mm) wide4.00YD3(3.1M3) w/bolt-on cutting edges, 114" (2894mm)wide (bucket tag)110% FILL FACTOR:4.50 YD3 (3.4 M3) with bolt-on edges, 114" (2894MM) wide (bucket tag)REQUIRES GET: Choose one set of adaptors, tips and optional

bolt-on segmentsFOR BOCE ARRANGEMENT - order bucket part: 559-9419

W 559-9419 BKTA GP GC 115" 4.00YD3 PO 3,505 $13,010 NI........................

Lane 1 Work ToolINCLUDES: 448-5092 Bucket-GP with Standard steelBolt-On Cutting Edge GP

W 461-6531 BKT GP GC 114" 4.25YD3 PO 3,161 $11,674 NI.........................

GC-TYPE PERFORMANCE SERIES BUCKETFOR USE WITH: 950GC Machines ONLYREQUIRES: G.E.T.CAPACITIES:4.00 YD3 (3.1 M3) w/bolt-on adapters, 117" (2972mm) wide4.25 YD3 (3.3 M3) w/bolt-on adapters and segments, 114" (2894mm) wide4.25YD3(3.3M3) w/bolt-on cutting edges, 114" (2894mm)wide (bucket tag)110% FILL FACTOR:4.75 YD3 (3.6 M3) with bolt-on edges, 114" (2894MM) wide (bucket tag)REQUIRES GET: Choose one set of adaptors, tips and optional bolt-onSEGMENTSFOR BOCE ARRANGEMENT - order bucket part: 559-9424

P 559-9424 BKTA GP GC 115" 4.25YD3 PO 3,593 $13,135 NI........................

Lane 1 Work Tool Cutting Edge GPINCLUDES: 461-6531 Bucket-GP with Standard steel

Bolt-On Cutting Edge GP







WT-MWL



950 GC WHEEL LOADER (CONT.)

GC-TYPE MATERIAL HANDLING PERFORMANCE SERIES (PIN-ON)

W 477-7221 BKT FF GC 114" 4.00YD3 PO 3,100 $11,393 NI.........................

GC-TYPE PERFORMANCE SERIES BUCKETFOR USE WITH: 950GC Machines ONLYREQUIRES: G.E.T.CAPACITIES:3.75 YD3 (2.9 M3) w/bolt-on adapters, 117" (2972mm) wide4.00 YD3 (3.1 M3) w/bolt-on adapters and segments, 114" (2894mm) wide4.00YD3(3.1M3) w/bolt-on cutting edges, 114"(2894mm)wide (bucket tag)110% FILL FACTOR:4.50 YD3 (3.4 M3) with bolt-on edges, 114" (2894MM) wide (bucket tag)

W 477-7372 BKT FF GC 114" 4.25YD3 PO 3,192 $11,710 NI.........................

GC-TYPE PERFORMANCE SERIES BUCKETFOR USE WITH: 950GC Machines ONLYREQUIRES: G.E.T.CAPACITIES:4.00 YD3 (23.1 M3) w/bolt-on adapters, 117" (2972mm) wide4.25 YD3 (3.3 M3) w/bolt-on adapters and segments, 114" (2894mm) wide4.25YD3(3.3M3) w/bolt-on cutting edges, 114"(2894mm)wide (bucket tag)110% FILL FACTOR:4.75 YD3 (3.6 M3) with bolt-on edges, 114" (2894MM) wide (bucket tag)

950GC COUPLER / FUSION

W 310-9391 QUICK COUPLER, FUSION 1,090 $6,778 NI............................

REQUIRES: Kit, Coupler Hydraulic Supply (530-2463)ONLY FOR USE WITH: 950 GC Machines

950GC COUPLER HYDRAULIC SUPPLY GROUP (FUSION)

W 530-2463 KIT, COUPLER HYDRAULIC SUPPLY 29 $1,978 NI........................

FOR USE WITH: 310-9391 Coupler950GC STANDARD LIFT machinesmachine seriel number prefix M5K and M5T

W 323-9292 JUMPER LINES FOR 3V QC 21 $1,082 NI..............................

REQUIRED: when coupler is used with hydraulic tools that require 3rdvalve

950GC BUCKETS / FUSION

GENERAL PURPOSE PERFORMANCE SERIES (FUSION)







WT-MWL




950GC BUCKETS / FUSION (Cont.)

W 382-9834 BKT GP ST 114" 4.00YD3 FUS 3,384 $13,931 NI........................

PERFORMANCE SERIES BUCKETFOR USE WITH: 950GC, 950G/H/KREQUIRES: G.E.T.CAPACITIES:3.75 YD3 (2.9 M3) with bolt-on adapters, 117"(2972mm) wide4.00 YD3 (3.1 M3) with bolt-on adapters and segments, 117"(2972mm)4.00 YD3 (3.1 M3) with bolt-on cutting edges, 114"(2894mm) wide110% FILL FACTOR:4.50 YD3 (3.4M3) with bolt on edges, 114" (2894MM) wide (bucket tag)REQUIRES GET: Choose one set of adaptors, one set of tips andoptional bolt-on segmentsFOR BOCE ARRANGEMENT - order bucket part: 559-9421

W 559-9421 BKTA GP ST 115" 4.00YD3 FUS 3,810 $15,392 NI.......................

PERFORMANCE SERIES BUCKETLane 1 Work ToolINCLUDES: 382-9834 Bucket-GP with Standard steelBolt-On Cutting Edge GP


PERFORMANCE SERIES BUCKETREQUIRES G.E.T.CAPACITIES:4.25 YD3 (3.2 M3) with bolt-on adapters, 117"(2972mm) wide4.50 YD3 (3.4 M3) with bolt-on adapters and segments, 117"(2972mm)4.50 YD3 (3.4 M3) with bolt-on cutting edges, 114"(2894mm) wide110% FILL FACTOR:4.80 YD3 (3.7 M3) with bolt on edges, 114" (2894MM) wide (bucket tag)

950GC BUCKET G.E.T.

BOLT ON CUTTING EDGE

W 139-9229 CUTTING EDGE, BOLT-ON 600 $1,461..............................

1.2" (30mm) thick, 114"(2894mm) wide(1 required)

ADVANSYS G.E.TA80 G.E.T. FOR GENERAL PURPOSE AND PERFORMANCEBUCKETS (INCLUDING MOUNTING HARDWARE)

W 539-5785 ADAPTERS, TIP, BOLT-ON, A080 316 $2,110........................

(1 required)Includes 8 AdaptersFOR USE WITH: A80 tips

W 505-3984 TIP, GENERAL DUTY 15 $89...................................

(8 required)FOR USE WITH: A80 adapters







WT-MWL




950GC BUCKET G.E.T. (Cont.)

W 107-3394 SEGMENTS, BOLT ON 334 $1,143.................................

Set of 7 segments, 35mm thick (1 required)ONLY FOR USE WITH: ADAPTERS, TIP, BOLT-ON & TIPS

PALLET FORK CARRIAGES (FUSION)

W 530-1861 ITA PALLET FORK CARRIAGE, 84" 1,321 $6,400 NI......................

84"(2134mm) CarriageFOR USE WITH: Fusion CouplerREQUIRES: 2 - Class IV Tines (Pallet Fork)CANNOT BE USED WITH: Class III construction tines

PALLET FORK TINES (FUSION)

W 530-1869 ITA TINE, PALLET FORK 72" 396 $2,429 NI............................

REQUIRES: 530-1861 CARRIAGE, 84"TINE WIDTH: 6" (150mm)TINE THICKNESS: 2.5" (65mm)



950 GC SNOW REMOVAL / FUSION

HYDRAULIC ANGLE SNOW BLADES

W 524-6848 BLD 144 HYD ANG SNW TRP FUS 3,020 $14,371 NI.....................

BLADE HEIGHT: 42" (1067mm)FOR USE WITH: Fusion Coupler

ONE AVAILABLE HYDRAULIC FUNCTIONS (E.G. 3F)WITH LINES GP-IMPLEMENT 3F INSTALLED

CANADIAN DEALERS REFERENCE WT-CADSNW PRICE LIST

W 524-6849 BLD 168 HYD ANG SNW TRP FUS 3,157 $18,518 NI......................



U/V ANGLE BLADES

W 524-6865 BLD 132 U/V ANG FUS 2,900 $29,628 NI..............................


TWO AVAILABLE HYDRAULIC FUNCTIONS (e.g. 3F & 4F)







WT-MWL




U/V ANGLE BLADES (Cont.)

W 524-6866 BLD 144 U/V ANG FUS 3,000 $33,332 NI..............................



W 542-1498 DIVERTER VALVE KIT, U/V ANG 0 $3,814 NI...........................

FOR USE WITH: OPTION FOR LOADERS WITH 3F ONLYREQUIRES: DEALER TO CREATE WIRING. HYDRAULICS ONLY.

SNOW PUSH

W 524-6872 BLD 180" SNOW PUSH FUS 6,913 $20,000 NI..........................

HEIGHT: 56" (1423mm)FOR USE WITH: Fusion Coupler

ICE SCRAPER

W 524-6876 SCARIFIER 147" FUS 3,309 $11,850 NI................................

V PLOW

W 314-2510 PLOW, 126" V SNOW 2,765 $10,297 NI...............................


950 & 962 WHEEL LOADER

950M/K & 962M/K BUCKETS / PIN ON

GENERAL PURPOSE PERFORMANCE SERIES (PIN-ON)

W 352-5537 BKT GP ST 114" 4.00YD3 PO 3,516 $14,101 NI.........................

PERFORMANCE SERIES BUCKETCAPACITIES:3.75YD3 (2.9M3) w/bolt-on adapters, 117"(2972mm) wide4.00YD3 (3.1M3) w/bolt-on adapters and segments, 117"(2972mm)4.00YD3 (3.1M3) w/bolt-on cutting edges, 114"(2894mm) wide(Bucket Tag)110% FILL FACTOR:4.50YD3(3.4M3) w/bolt-on cutting edges, 114"(2894mm) wide(Bucket Tag)Requires GET: Choose either bolt-on cutting edge with corner guardor one set of adaptors, one set of tips and optional bolt-on segments.







WT-MWL



950 & 962 WHEEL LOADER (CONT.)

950M/K & 962M/K BUCKETS / PIN ON (Cont.)

W 354-4853 BKT GP ST 114" 4.50YD3 PO 3,721 $14,967 NI.........................

PERFORMANCE SERIES BUCKETCAPACITIES:4.25YD3 (3.2M3) with bolt-on adapters, 117"(2972mm) wide4.50YD3 (3.4M3) with bolt-on adapters and segments, 117"(2972mm)4.50YD3(3.4M3) w/bolt-on cutting edges, 114"(2894mm) wide(Bucket Tag)110% FILL FACTOR:4.75YD3(3.7M3) w/bolt-on cutting edges, 114"(2894mm) wide(Bucket Tag)Requires GET: Choose one set of adaptors, one set of tips andoptional bolt-on segmentsFor BOCE Arrangement - order bucket part: 516-1452

W 516-1452 BKTA GP ST 115" 4.50YD3 PO 4,242 $16,428 NI........................

Lane 1 Work ToolINCLUDES: 354-4853 Bucket-GP with Standard steel Bolt-On Cutting Edges

W 354-4855 BKT GP ST 114" 4.75YD3 PO 3,803 $15,392 NI.........................

PERFORMANCE SERIES BUCKETCAPACITIES:4.50YD3 (3.4M3) with bolt-on adapters, 117"(2972mm) wide4.75YD3 (3.6M3) with bolt-on adapters and segments, 117"(2972mm)4.75YD3 (3.6M3) w/bolt-on cutting edges, 114"(2894mm) wide(Bucket Tag)110% FILL FACTOR:5.25YD3(4.0M3) w/bolt-on cutting edges, 114"(2894mm) wide(Bucket Tag)Requires GET: Choose one set of adaptors, one set of tips andoptional bolt-on segmentsFor BOCE Arrangement - order bucket part: 516-2814


Lane 1 Work ToolINCLUDES: 354-4855 Bucket-GP with Standard steel Bolt-On Cutting Edges

W 376-7800 BKT GP ST 114" 5.00YD3 PO 3,907 $15,867 NI.........................

PERFORMANCE SERIES BUCKETCAPACITIES:4.75YD3(3.6M3) w/bolt-on adapters, 117"(2972mm) wide5.00YD3(3.8M3) w/bolt-on adapters and segments, 117"(2972mm)5.00YD3(3.8M3) w/bolt-on cutting edges, 114"(2894mm) wide(Bucket Tag)110% FILL FACTOR:5.50YD3(4.20M3) w/bolt-on cutting edges, 114"(2894mm) wide(Bucket Tag)Requires GET: Choose one set of A80 adaptors, one set of tips (8 qty)and optional bolt-on segmentsFor BOCE Arrangement - order bucket part: 516-2560


Lane 1 Work ToolPERFORMANCE SERIES BUCKETINCLUDES: 376-7800 Bucket-GP with BOCE







WT-MWL




General Purpose-Abrasion (PIN ON)

W 395-2119 BKTA GP AB 118" 5.00YD3 PO 4,610 $19,242 NI........................



FLAT FLOOR PERFORMANCE SERIES (PIN-ON)

W 354-4865 BKT FF ST 114" 4.50YD3 PO 3,704 $14,942 NI.........................


W 354-4867 BKT FF ST 114" 5.00YD3 PO 3,918 $15,885 NI.........................


MULTI-PURPOSE (PIN ON)

W 380-8308 BKTA MP ST 116" 3.75YD3 PO 4,687 $29,831 NI........................

116" (2943mm) wideINCLUDES: Bolt-on Cutting EdgeREQUIRES: 3rd valve

SIDE DUMP (PIN ON)

W 383-2233 BKTA SD ST 127" 3.75 YD3 PO 5,413 $30,586 NI.......................








WT-MWL




HIGH DUMP (PIN-ON)

For light materials only - Applications include woodchips,grains and wood pellets. Not intended for waste applications.

W 521-1706 BKTA HD ST 120" 8.0 YD3 PO 6,617 $35,449 NI........................

120" (3037mm) wideINCLUDES: Bolt on Cutting EdgeREQUIRES: 3rd valve

W 521-1704 BKTA HD ST 132" 10.0 YD3 PO 7,129 $38,438 NI.......................




WASTE HANDLING (PIN-ON)

950K / 962K

W 516-3001 BKTA WD LM 120" 6.75YD3 PO 5,139 $21,632 NI.......................

Dozing style bucket121" (3059mm) wideIncludes: 309-1062 CUTTING EDGE, BOLT-ON (steel)CAPACITIES:6.75YD3 with Bolt-on cutting edge18.00YD3 Dozing capacity with Bolt-on cutting edge

W 516-3013 BKTA WD LM 119" 6.75YD3 PO 5,146 $23,444 NI.......................

Dozing style bucket121" (3059mm) wideIncludes: 437-0288 CUTTING EDGE, BOLT-ON RUBBERCAPACITIES:6.75YD3 with Bolt-on cutting edge18.00YD3 Dozing capacity with Bolt-on cutting edge

W 516-2981 BKTA WLC ST 120" 8.00YD3 PO 5,895 $26,179 NI......................

Load and Carry style bucket121" (3059mm) wideIncludes: 309-1062 CUTTING EDGE, BOLT-ON (Steel)CAPACITIES:8.00YD3 with Bolt-on cutting edge







WT-MWL




WASTE HANDLING (PIN-ON) (Cont.)

W 516-2903 BKTA WLC ST 119" 8.00YD3 PO 5,900 $27,992 NI.......................

Load and Carry style bucket.121" (3059mm) wide.Includes: 437-0288 CUTTING EDGE, BOLT-ON RUBBERCAPACITIES:8.00YD3 with Bolt-on cutting edge.

W 449-4377 BKT WTC ST 121" 5.75 YD3 PO 7,929 $33,892 NI.......................

Waste Handling bucket with clamp for light sorting or dozingwhen fully open.121" (3059mm) wideREQUIRES: 309-1062 CUTTING EDGE, BOLT-ON (steel) or

437-0288 CUTTING EDGE, BOLT-ON RUBBERALSO REQUIRES: 3rd ValveCAPACITIES:5.50YD3 with Bolt-on cutting edge

WOODCHIP (PIN-ON)

For light materials only - Applications include woodchips, snow,grains and wood pellets. Not intended for waste applications.

W 354-4873 BKTA WC ST 131" 12.00YD3 PO 5,401 $29,529 NI.......................

131" (3330mm) wideINCLUDES: Bolt-on Cutting EdgeCAPACITIES:12.0YD3 (9.2m3) with Bolt-on cutting edge

W 354-4875 BKTA WC ST 131" 13.00YD3 PO 5,600 $30,981 NI.......................

131" (3330mm) wideINCLUDES: Bolt-on Cutting EdgeCAPACITIES:13.0YD3(9.9M3) with Bolt-on cutting edge

950M/K & 962M/K BUCKETS / FUSION

GENERAL PURPOSE (FUSION)







WT-MWL




950M/K & 962M/K BUCKETS / FUSION (Cont.)


PERFORMANCE SERIES BUCKETFOR USE WITH: Fusion CouplerCAPACITIES:3.75YD3 (2.9M3) w/bolt-on adapters, 117"(2972mm) wide4.00YD3 (3.1M3) w/bolt-on adapters and segments, 117"(2972mm)4.00YD3 (3.1M3) w/bolt-on cutting edges, 114"(2894mm) wide(Bucket Tag)110% FILL FACTOR:4.50YD3(3.4M3) w/bolt-on cutting edges, 114"(2894mm) wide (Bucket Tag)Requires GET: Choose one set of adaptors, one set of tips andoptional bolt-on segmentsFor BOCE Arrangement - order bucket part: 516-3431


PERFORMANCE SERIES BUCKETINCLUDES: 348-0242 Bucket-GP with BOLT-ON CUTTING EDGE (BOCE)


PERFORMANCE SERIES BUCKETFOR USE WITH: Fusion CouplerCAPACITIES:4.25YD3(3.2M3) w/bolt-on adapters, 117"(2972mm) wide4.50YD3(3.4M3) w/bolt-on adapters and segments, 117"(2972mm)4.50YD3(3.4M3) w/bolt-on cutting edges, 114"(2894mm) wide(Bucket Tag)110% FILL FACTOR:5.00YD3(3.7M3) w/bolt-on cutting edges, 114"(2894mm) wide(Bucket Tag)Requires GET: Choose one set of adaptors, one set of tips andoptional bolt-on segmentsFor BOCE Arrangement - order bucket part: 516-1417


Lane 1 Work ToolINCLUDES: 354-4854 BUCKET-GP with Bolt-on cutting edge (BOCE)


PERFORMANCE SERIES BUCKETFOR USE WITH: Fusion CouplerCAPACITIES:4.50YD3(3.4M3) w/bolt-on adapters, 117"(2972mm) wide4.75YD3(3.6M3) w/bolt-on adapters and segments, 117"(2972mm)4.75YD3(3.6M3) w/bolt-on cutting edges, 114"(2894mm) wide(Bucket Tag)110% Fill Factor:5.25YD4(4.0M3) w/bolt-on cutting edges, 114"(2894mm) wide(Bucket Tag)Requires GET: Choose one set of adaptors, one set of tips andoptional bolt-on segmentsFor BOCE Arrangement - order bucket part: 516-2827


Lane 1 Work ToolINCLUDES: 354-4856 BUCKET-GP with bolt-on cutting edge







WT-MWL






PERFORMANCE SERIES BUCKETFOR USE WITH: Fusion CouplerCAPACITIES:4.75YD3(3.6 M3) w/bolt-on adapters, 117"(2972mm) wide5.00YD3(3.8 M3) w/bolt-on adapters and segments, 117"(2972mm)5.00YD3(3.8 M3) w/bolt-on cutting edges, 114"(2894mm) wide(Bucket Tag)110% FILL FACTOR5.50YD3(4.2M3) w/bolt-on cutting edges, 114"(2894mm) wide(Bucket Tag)Requires GET: Choose one set of A80 adaptors, one set of tips (8 qty)and optional bolt-on segmentsFor BOCE Arrangement - order bucket part: 516-2761


PERFORMANCE SERIES BUCKETINCLUDES: 376-7801 Bucket-GP with BOCE

FLAT FLOOR PERFORMANCE SERIES (FUSION)

W 354-4866 BKT FF ST 114" 4.50YD3 FUS 3,411 $14,515 NI........................

PERFORMANCE SERIES BUCKETFOR USE WITH: Fusion CouplerCAPACITIES:4.25YD3(3.2M3) w/bolt-on adapters, 117"(2972mm) wide4.50YD3(3.4M3) w/bolt-on adapters and segments, 117"(2972mm)4.50YD3(3.4M3) w/bolt-on cutting edges, 114"(2894mm) wide(Bucket Tag)110% FILL FACTOR:5.00YD3(3.7M3) w/bolt-on cutting edges, 114"(2894mm) wide(Bucket Tag)Requires GET: Choose either bolt-on cutting edge with corner guardor one set of adaptors, one set of tips and optional bolt-on segments.

W 354-4868 BKT FF ST 114" 5.00YD3 FUS 3,611 $15,389 NI.........................

PERFORMANCE SERIES BUCKETFOR USE WITH: Fusion CouplerCAPACITIES:4.75YD3(3.6M3) w/bolt-on adapters, 117"(2972mm) wide5.00YD3(3.8M3) w/bolt-on adapters and segments, 117"(2972mm)5.00YD3(3.8M3) w/bolt-on cutting edges, 114"(2894mm) wide(Bucket Tag)110% FILL FACTOR:5.50YD3(4.2M3) w/bolt-on cutting edges, 114"(2894mm) wide(Bucket Tag)Requires GET: Choose either bolt-on cutting edge with corner guardor one set of adaptors, one set of tips and optional bolt-on segments.

SPECIAL APPLICATION (FUSION)

MULTI-PURPOSE (FUSION)







WT-MWL





W 313-1397 BKTA MP ST 116" 3.75 YD3 FUS 4,601 $29,361 NI......................

116" (2943mm) wideINCLUDES: Bolt-on Cutting EdgeFOR USE WITH: Fusion CouplerREQUIRES: 3rd vavle

SIDE DUMP (FUSION)

W 314-2547 BKTA SD ST 127" 3.75 YD3 FUS 5,177 $30,586 NI......................

127" (3220mm) wideINCLUDES: Bolt-on Cutting EdgeFOR USE WITH: Fusion CouplerREQUIRES: 3rd valve

HIGH DUMP (FUSION)

For heavy duty applications such as waste or handlingheaping materials such as compost.

W 312-1727 BKTA HD ST 115" 6.0 YD3 FUS 5,891 $53,157 NI.......................




HIGH DUMP (FUSION)



120" (3037mm) wideINCLUDES: Bolt-on cutting edgeREQUIRES: 3rd valve







WT-MWL





W 521-1762 BKTA HD ST 132" 10.0 YD3 FUS 7,131 $38,438 NI......................




WASTE HANDLING (FUSION)

W 519-3516 BKT WD ST 119" 6.75 YD3 FUS 4,319 $18,065 NI.......................

Lane 1 Work ToolDozing style bucket121" (3059mm) wideREQUIRES: Bolt-on cutting steel edge 309-1062 or rubber edge 437-0288CAPACITIES:6.75 CYD with Bolt-on cutting edge18.00 CYD Dozing capacity with Bolt-on cutting edge

WOODCHIP (FUSION)


W 354-4874 BKTA WC ST 131" 12.00YD3 FUS 5,227 $29,454 NI......................

131" (3330mm) wideINCLUDES: Bolt-on Cutting EdgeFOR USE WITH: Fusion CouplerCAPACITIES:12.0YD3 (9.2M3) w/bolt-on cutting edges


131" (3330mm) wideINCLUDES: Bolt-on Cutting EdgeFOR USE WITH: Fusion CouplerCAPACITIES:13.0YD3 (9.9M3) w/bolt-on cutting edges

950 & 962 BUCKET G.E.T.








WT-MWL




950 & 962 BUCKET G.E.T. (Cont.)


1.2" (30mm) thick, 114" (2894mm) wide, (1 required)

W 174-7949 GUARD, CORNER 81 $678......................................

FOR USE WITH: General Purpose Buckets with Bolt-OnCutting Edges Only


1.2" (30mm) thick, 121" (3059mm) wide (1 required)FOR USE WITH: 519-3516 Dozing Bucket

449-4377 Waste Handling Bucket

W 437-0288 CUTTING EDGE, BOLT-ON RUBBER 293 $4,410........................

1.2" (30mm) thick, 121" (3059mm) wide (1 required)FOR USE WITH: 519-3516 Dozing Bucket

449-4377 Waste Handling Bucket

W 174-7948 GUARD, CORNER 67 $439......................................

FOR USE WITH: 139-9229 CUTTING EDGE, BOLT-ON

A80 G.E.T. FOR GENERAL PURPOSE AND FLAT FLOOR BUCKETS(INCLUDING MOUNTING HARDWARE)


(1 required)FOR USE WITH: A80 tips


35mm thick. (1 required)FOR USE WITH: A80 adapters and tips


FOR USE WITH: A80 adapters (8 required)W 505-3982 TIPS AS, HEAVY DUTY 18 $107.................................

FOR USE WITH: A80 adapters (8 required)W 505-4081 TIP, PENETRATION 14 $75....................................

FOR USE WITH: A80 adapters (8 required)







WT-MWL




950M/K & 962M/K COUPLERS / FUSION


Lane 1 Work ToolREQUIRES: Supply Group

950M & 962M COUPLER SUPPLY GROUPS (FUSION)


Lane 1 Work ToolFOR USE WITH: 349-5246 Coupler

950M STANDARD LIFT machinesmachine serial number prefix EMB, XCJ, J1S,FTR, ENE and LCR


Lane 1 Work ToolFOR USE WITH: 349-5246 Coupler

962M STANDARD LIFT machinesmachine serial number prefix EJB, JYD, J2S, F2T,LSE and RCL


FOR USE WITH: 349-5246 Coupler950M/962M HIGH LIFT machinesmachine serial number prefix EMB, XCJ, J1S, FTR,ENE and LCRmachine serial number prefix EJB, JYD, J2S, F2T,LSE and RCL

950K & 962K COUPLER SUPPLY GROUPS


FOR USE WITH: 349-5246 CouplerFOR USE WITH: 950K STANDARD LIFT Machines

machine serial number prefix R4A, FER, J5M and LRN


FOR USE WITH: 349-5246 CouplerFOR USE WITH: 962K STANDARD LIFT Machines

machine serial number prefix X4T, FLL, T6A and MRM

W 368-0687 KIT, COUPLER HYDRAULIC SUPPLY 111 $1,626 NI.......................

FOR USE WITH: 349-5246 CouplerFOR USE WITH: 950K/962K HIGH LIFT Machines

machine serial number prefix R4A, FER, J5M and LRNmachine serial number prefix X4T, FLL, T6A and MRM

950M/K & 962M/K COUPLER CONNECTOR LINES (FUSION)







WT-MWL




950K & 962K COUPLER SUPPLY GROUPS (Cont.)

W 378-8421 LINES GP-IMPLEMENT 3V (QC) 22 $560 NI...........................

REQUIRED: When coupler is used with hydraulic tools thatrequire 3rd valve.

W 378-8422 LINES GP-IMPLEMENT 3V&4V (QC) 44 $1,118 NI........................

REQUIRED: When coupler is used with hydraulic tools that require3rd and/or 4th valve.

950M/K & 962M/K FORKS / PIN ON

LOGGING (PIN ON)

W 379-5408 FORK, LOGGING 64" 5,451 $41,268 NI................................

90"(2298mm) carriage and 64"(1609mm) tinesINCLUDES: Double Top Clamp, GET tips and connecting linesREQUIRES: 3rd valve

LOG AND LUMBER (PIN-ON)

W 379-2323 FORK, LOG & LUMBER 48" 2,504 $12,978 NI...........................

96"(2438mm) carriage and 48"(12194mm) non-swinging tines

W 379-2340 FORK, LOG & LUMBER 60" 2,948 $14,051 NI............................






LOG AND LUMBER W/ SEMI-MILLYARD TOP CLAMP (PIN ON)

W 382-7885 FORK, LOG & LUMBER SM 76" 4,370 $30,713 NI........................

76"(1923mm) carriage and 48"(1219mm) tinesINCLUDES: Millyard top clamp and connecting linesREQUIRES: 3rd valve

UNLOADING GRAPPLE (PIN ON)

W 396-8852 FORK, GRAPPLE 36" 4,949 $38,838 NI................................

73"(1850mm) carriage and 36"(917mm) tinesINCLUDES: Top clamp and connector lines from coupler to the toolREQUIRES: 3rd valve







WT-MWL




950M/K & 962M/K FORKS / PIN ON (Cont.)

SORTING GRAPPLE (PIN ON)

W 417-3422 FORK, GRAPPLE 48" 5,260 $39,649 NI................................








WT-MWL




950M/K & 962M/K FORKS / PIN ON (Cont.)

MILLYARD (PIN ON)

W 374-7148 FORK, MILLYARD 64" 5,865 $38,531 NI...............................

90"(2286mm) carriage and 64"(1609mm) tinesINCLUDES: Millyard top clamp, GET tips and connecting linesREQUIRES: 3rd valve

MILLYARD POLE (PIN ON)

W 384-3214 FORK, MILLYARD POLE 66" 4,506 $39,121 NI...........................

86"(2184mm) carriage and 66"(1677mm) tinesINCLUDES: Millyard top clamp, Roller tips and connecting linesREQUIRES: 3rd valve


86"(2184mm) carriage and 66"(1677mm) tinesINCLUDES: Millyard top clamp, Solid tips and connecting linesREQUIRES: 3rd valve

W 390-6753 BUCKET-CU, 132" 8.00 YD3 4,379 $12,946 NI..........................

Slips on over Millyard Pole ForksFOR USE WITH: 384-3214, 445-2466, 442-4392 and 445-2489

PIPE AND POLE FORK (PIN ON)

W 377-2845 FORK, PIPE & POLE 4,500 $45,290 NI.................................

108"(2731mm) carriage and 72"(1829mm) tinesINCLUDES: Connector Lines from the coupler to the toolTINE WIDTH: 8" (203mm)TINE THICKNESS: 3" (76mm)

950M/K & 962M/K FORKS / COUPLER / FUSION

LOG AND LUMBER (FUSION)


84"(2134mm) carriage and 48"(1219mm) non-swinging tinesFOR USE WITH: Fusion couplerTINE WIDTH: 7" (180mm)TINE THICKNESS: 2.5" (65mm)







WT-MWL




950M/K & 962M/K FORKS / COUPLER / FUSION (Cont.)


84" (2134mm) carriage and 60"(1524mm) non-swinging tinesFOR USE WITH: Fusion couplerTINE WIDTH: 7" (180mm)TINE THICKNESS: 3.5" (90mm)


84" (2134mm) carriage and 72"(1829mm) non-swinging tinesFOR USE WITH: Fusion couplerTINE WIDTH: 7" (180mm)TINE THICKNESS: 3.5" (90mm)


84" (2134mm) carriage and 96" (2438mm) non-swinging tinesFOR USE WITH: Fusion couplerTINE WIDTH: 7" (180mm)TINE THICKNESS: 3.5" (90mm)




96"(2438mm) carriage and 60"(1524mm) non-swinging tinesFOR USE WITH: Fusion couplerTINE WIDTH: 7"(180mm)TINE THICKNESS: 3.5"(90mm)





LOG AND LUMBER W/ SEMI-MILLYARD TOP CLAMP (FUSION)







WT-MWL





W 380-8227 FORK, LOG & LUMBER SM 72" 4,425 $30,713 NI........................

76"(1923mm) carriage and 48"(1219mm) tinesINCLUDES: Millyard top clamp and connector lines from

coupler to the tool.FOR USE WITH: Fusion CouplerREQUIRES:3rd valve,connector lines from machine to machine to coupler.TINE WIDTH: 7"(180mm)TINE THICKNESS: 3"(76mm)

UNLOADING GRAPPLE (FUSION)

W 377-0722 FORK, GRAPPLE 30" 4,253 $38,031 NI................................


W 352-7339 FORK, GRAPPLE 36" 4,729 $38,838 NI................................


W 361-3084 FORK, GRAPPLE 36" 5,664 $51,785 NI................................

73"(1850mm) carriage and 36"(917mm) tinesINCLUDES: Top clamp, Kick out and connector lines from coupler to theREQUIRES: 3rd and 4th valve.

SORTING GRAPPLE (FUSION)

W 442-9358 FORK, GRAPPLE 48" 5,082 $39,649 NI................................


MILLYARD (FUSION)


90" (2286mm) carriage and 64" (1609mm) tinesINCLUDES: Millyard top clamp, GET tips and connector linesREQUIRED: 3rd valve

MILLYARD POLE (FUSION)


73"(1855mm) carriage and 48"(1219mm) tinesINCLUDES: Millyard top clamp, Roller tips and connecting lineREQUIRES: 3rd valve







WT-MWL






86"(2184mm) carriage and 66"(1677mm) tinesINCLUDES: Millyard top clamp, Solid tips and connecting linesREQUIRES: 3rd valve

W 390-6753 BUCKET-CU, 132" 8.00 YD3 4,379 $12,946 NI..........................

Slips on over Millyard Pole ForksFOR USE WITH: 384-3214, 445-2466, 442-4392 and 445-2489









CONSTRUCTION FORK CARRIAGES (FUSION)

W 520-7957 CARRIAGE GROUP, 96" 1,761 $8,000 NI..............................

Lane 1 Work Tool - Ships loose from Caterpillar Work Tools & Services96"(2438mm) carriageFOR USE WITH: Fusion CouplerREQUIRES: TINE GROUP

W 520-7968 CARRIAGE GROUP, 108" 1,877 $9,199 NI.............................

108"(2743mm) carriageFOR USE WITH: Fusion CouplerREQUIRES: TINE GROUP

CONSTRUCTION FORK TINE GROUPS (FUSION)







WT-MWL




CONSTRUCTION FORK CARRIAGES (FUSION) (Cont.)

W 520-7985 TINE GROUP, 48" 1,012 $4,013 NI..................................

INCLUDES: Right and Left offset tines.REQUIRES: Carriage Group 520-7957 or 520-7968TINE WIDTH: 7" (180mm)TINE THICKNESS: 3.5" (90mm)

W 520-7980 TINE GROUP, 60" 1,150 $5,276 NI..................................

Lane 1 Work ToolINCLUDES: Right and Left offset tines.REQUIRES: Carriage Group 520-7957 or 520-7968TINE WIDTH: 7" (180mm)TINE THICKNESS: 3.5" (90mm)

W 520-7979 TINE GROUP, 72" 1,288 $6,786 NI..................................


W 520-7986 TINE GROUP, 84" 1,425 $9,425 NI..................................


W 520-7981 TINE GROUP, 96" 1,562 $11,714 NI..................................


PIPE AND POLE (FUSION)


106"(2693mm) Carriage, 72"(1829mm) TinesINCLUDES: Connector linesFOR USE WITH: Fusion CouplerREQUIRES: 3rd ValveTINE WIDTH: 8"(204mm)TINE THICKNESS: 3"(77mm)







WT-MWL




950M/K & 962M/K MATERIAL HANDLING ARMS / FUSION

W 289-9885 ARM, MATERIAL HANDLING 1,560 $7,635 NI..........................

Lane 1 Work Tool - Ships loose from Caterpillar Work Tool & ServicesExtendable Lenth 123" (3124mm) to 183" (4648mm)FOR USE WITH: Fusion Coupler

950M/K & 962M/K SNOW REMOVAL / FUSION



BLADE HEIGHT: 42" (1067mm)FOR USE WITH: Fusion CouplerREQUIRES: ONE AVAILABLE HYDRAULIC FUNCTIONS (E.G. 3F) WITH LINES GP-

IMPLEMENT 3F INSTALLEDCANADIAN DEALERS REFERENCE WT-CADSNW PRICE LIST


BLADE HEIGHT: 42" (1067mm)FOR USE WITH: Fusion CouplerREQUIRES: ONE AVAILABLE HYDRAULIC FUNCTIONS (E.G. 3F) WITH LINES GP-

IMPLEMENT 3F INSTALLEDCANADIAN DEALERS REFERENCE WT-CADSNW PRICE LIST

U/V ANGLE BLADES (FUSION)

W 524-6865 BLD 132 U/V ANG FUS 2,900 $29,628 NI..............................

BLADE HEIGHT: 40" (1016mm)FOR USE WITH: Fusion CouplerREQUIRES: TWO AVAILABLE HYDRAULIC FUNCTIONS (e.g. 3F & 4F)CANADIAN DEALERS REFERENCE WT-CADSNW PRICE LIST

W 524-6866 BLD 144 U/V ANG FUS 3,000 $33,332 NI..............................

BLADE HEIGHT: 40" (1016mm)FOR USE WITH: Fusion CouplerREQUIRES: TWO AVAILABLE HYDRAULIC FUNCTIONS (e.g. 3F & 4F)CANADIAN DEALERS REFERENCE WT-CADSNW PRICE LIST

SNOW PUSH (FUSION)











WT-MWL




ICE SCRAPER (FUSION)


FOR USE WITH: Fusion Coupler

V PLOW (FUSION)

W 314-2510 PLOW, 126" V SNOW 2,765 $10,297 NI...............................








WT-MWL




950H/G/K & 962H/G/K BROOMS

HYDRAULIC ANGLE BROOMS

W 202-9000 BA30 ANGLE BROOM, HYD, 24V 1,100 $19,015 NI......................

(BCP PRODUCT)Excluding hook group, 915mm (36") brush diameterHydraulic angling 30 degr. left/right of center using 24V Divert ValveSweeping width straight - max angled: 3000mm (118") - 2590mm (102")Brush material - 50% Polypropylene / 50% Steel WireREQUIRES: Machine side: Hydr. 3rd valve group with front lines + QDs,Continious flow, Kit Electrical Switch (see "BROOM KITS" below)

REQUIRES: Broom side: hook group and QDs kit

W 202-8999 BA30 ANGLE BROOM, HYD, 24V,WTR 1,540 $24,965 NI..................

(BCP PRODUCT)Excluding hook group, 915mm (36") brush diameterHydraulic angling 30 degr. left/right of center using 24V Divert ValveSweeping width straight - max angled: 3000mm (118") - 2590mm (102")Brush material - 50% Polypropylene / 50% Steel WireINCLUDES: Water sprinklers, 24V water pump and 600L watertankREQUIRES: Machine side: Hydr. 3rd valve group with front lines + QDs,Continious flow, Kit Electrical Switch (see "BROOM KITS" below)


MANUAL ANGLE BROOMS

W 202-7700 BA30 ANGLE BROOM, MAN 1,078 $17,915 NI..........................

(BCP PRODUCT)Excluding hook group, 915mm (36") brush diameterManual angling - 0, 15 and 30 degrees left or right of centerSweeping width straight - max angled: 3000mm (118") - 2590mm (102")Brush material - 50% Polypropylene / 50% Steel WireREQUIRES: Machine side: Hydraulic 3rd valve group with front lines,Continious flow, Hydraulic quick couplings kit








WT-MWL




950H/G/K & 962H/G/K BROOMS (Cont.)

SPECIAL APPLICATION BROOMS

W 257-9680 SA30 ANGLE BROOM, HYD, HO, 24V 1,520 $21,869 NI..................

(BCP PRODUCT)Excluding hook groupHydraulic angling 30 degr. left/right of center using 24V Divert Valve915mm (36") brush diameter, Brush material - 100% PolypropyleneSweeping width straight - max angled: 3000mm (118") - 2590mm (102")REQUIRES: Machine side: Hydr. 3rd valve group with front lines + QDs,

Continious flow, Kit Electrical Switch (see "BROOM KITS" below)REQUIRES: Broom side: hook group and QDs kit

BROOM ELECTRICAL KIT

W 205-9410 KIT, BROOM, ELEC, MWL 11 $354 NI...............................

(BCP PRODUCT)

BROOM HOOK GROUPS

W 497-9469 HOOK, BROOM, FUSION 324 $1,111 NI...............................

(BCP PRODUCT)FOR USE WITH: BA30

W 487-8481 HOOK, BROOM, IT38 112 $1,111 NI.................................

(BCP PRODUCT)FOR USE WITH: standard quick coupler IT 38

BROOM QUICK COUPLING KIT

W 200-0724 KIT, CONVERSION TEMA 3 $215 NI.................................

(BCP PRODUCT)FOR USE WITH: Machines using nipple type quick disconnects







WT-MWL




950L/H/G & 962L/H/G BUCKETS / PIN-ON


W 415-3251 BKT GP ST 114" 3.50YD3 PO 3,205 $13,182 NI.........................

PERFORMANCE SERIES BUCKETCAPACITIES:3.25 YD3 (2.5 M3) with bolt-on adapters, 117"(2972mm) wide3.50 YD3 (2.7 M3) with bolt-on adapters and segments, 117"(2972mm)3.50 YD3 (2.7 M3) with bolt-on cutting edges, 114"(2894mm) wideRequires GET: Choose either bolt-on cutting edge with corner guard orone set of A80 adaptors, one set of tips and optional bolt-on segments

W 391-4950 BKT GP ST 114" 4.00YD3 PO 3,404 $13,956 NI.........................

PERFORMANCE SERIES BUCKETCAPACITIES:3.75 YD3 (2.9 M3) with bolt-on adapters, 117"(2972mm) wide4.00 YD3 (3.1 M3) with bolt-on adapters and segments, 117"(2972mm)4.00 YD3 (3.1 M3) with bolt-on cutting edges, 114"(2894mm) wide

W 395-3265 BKT GP ST 114" 4.25YD3 PO 3,503 $14,367 NI.........................

PERFORMANCE SERIES BUCKETCAPACITIES:4.00 YD3 (3.1 M3) with bolt-on adapters, 117"(2972mm) wide4.25 YD3 (3.3 M3) with bolt-on adapters and segments, 117"(2972mm)4.25 YD3 (3.3 M3) with bolt-on cutting edges, 114"(2894mm) wideRequires GET: Choose either bolt-on cutting edge with corner guard orone set of A80 adaptors, one set of tips (8 qty) and optional bolt-onsegments

W 394-8476 BKT GP ST 114" 4.50YD3 PO 3,567 $14,743 NI.........................


W 395-3949 BKT GP ST 114" 4.75YD3 PO 3,697 $15,231 NI.........................

PERFORMANCE SERIES BUCKETCAPACITIES:4.50 YD3 (3.4 M3) with bolt-on adapters, 117"(2972mm) wide4.75 YD3 (3.6 M3) with bolt-on adapters and segments, 117"(2972mm)4.75 YD3 (3.6 M3) with bolt-on cutting edges, 114"(2894mm) wide

ROCK (PIN-ON)







WT-MWL




950L/H/G & 962L/H/G BUCKETS / PIN-ON (Cont.)

W 595-0410 BKTA RSP AB 118" 4.50YD3 PO 4,030 $26,149 NI.......................

Spade edge.118"(2985mm) wideINCLUDES: 5 piece bolt-on cutting edge system

950H/G & 962H/G BUCKETS / COUPLER / FUSION

GENERAL PURPOSE PERFOMANCE SERIES (FUSION)


PERFORMANCE SERIES BUCKETCAPACITIES:3.75 YD3 (2.9 M3) with bolt-on adapters, 117"(2972mm) wide4.00 YD3 (3.1 M3) with bolt-on adapters and segments, 117"(2972mm)4.00 YD3 (3.1 M3) w/bolt-on cutting edges,114"(2894mm)wide(bucket tag)110% FILL FACTOR:4.50 YD3 (3.4M3) with bolt-on edges, 114" (2894MM) wide (bucket tag)Includes Bolt On Cutting Edge GP




MULTIPURPOSE (FUSION)

W 313-1397 BKTA MP ST 116" 3.75 YD3 FUS 4,601 $29,361 NI......................

INCLUDES: Bolt on EdgeREQUIRES: 3rd valve

SIDE-DUMP (FUSION)



WASTE HANDLING (FUSION)







WT-MWL




950H/G & 962H/G BUCKETS / COUPLER / FUSION (Cont.)

W 311-6944 BKTA WD ST 120" 6.75 YD3 FUS 4,844 $24,256 NI......................

INCLUDES: Bolt on Edge

COAL (FUSION)

W 314-3191 BKT FF LM 130" 7.5 YD3 FUS 4,251 $21,206 NI.........................

130"(3307mm) wideREQUIRES: Bolt on Edge

950 & 962 BUCKET G.E.T.



30mm thick (1 required)

ADVANSYS GETA80 G.E.T. FOR GENERAL PURPOSE AND FLAT FLOOR BUCKETS




35mm thick. (1 required)FOR USE WITH: A80 adapters and tips


FOR USE WITH: A80 adapters (8 required)W 505-3982 TIPS AS, HEAVY DUTY 18 $107.................................


950L & 962L COUPLERS / FUSION


Lane 1 Work ToolFOR USE WITH: 950L and 962L machines950L machine serial number prefix LXX and TNS962L machine serial number prefix SXS and MTN

950L & 962L COUPLER SUPPLY GROUPS (FUSION)


FOR USE WITH: 310-9391 Coupler950L STANDARD LIFT machinesMachine serial number prefix LXX and TNS







WT-MWL




950L & 962L COUPLER SUPPLY GROUPS (FUSION) (Cont.)


FOR USE WITH: 310-9391 Coupler962L STANDARD LIFT machinesMachine serial number prefix SXS and MTN


FOR USE WITH: 310-9391 Coupler950L/962L HIGH LIFT machines950L Machine serial number prefix LXX and TNS962L Machine serial number prefix SXS and MTN

950L & 962L COUPLER CONNECTOR LINES (FUSION)


FOR USE WITH: 950L and 962L machinesREQUIRED: When coupler is used with hydraulic tools that require3rd valve.

950L & 962L COUPLER TILT LINK (FUSION)

W 475-0944 LINK, TILT 197 $1,635 NI.........................................

FOR USE WITH: 310-9391 Fusion Coupler on 950L and 962L HIGH LIFTlinkage machines

950H & 962H COUPLER / FUSION


Lane 1 Work Tool - Ships loose from Caterpillar Work Tool & ServicesFOR USE WITH: 950H/962H and 950G/962G series II machines

950H & 962H COUPLER SUPPLY GROUPS (FUSION)


FOR USE WITH: 310-9391 CouplerFOR USE WITH: 950H STANDARD LIFT machines

machine serial number prefix K5K, M1G, J5J, JAD and N1AFOR USE WITH: 962H STANDARD LIFT machines

machine serial number prefix K6K, M3G, J6J, MAL and N4AW 315-6316 KIT, COUPLER HYDRAULIC SUPPLY 44 $1,626 NI........................

FOR USE WITH: 310-9391 CouplerFOR USE WITH: 950H HIGH LIFT Machines

Machine serial number K5K, M1G, J5J, JAD, N1AFOR USE WITH: 962H HIGH LIFT Machines

Machine serial number K6K, M3G, J6J, MAL, N4AW 444-6448 KIT, COUPLER HYDRAULIC SUPPLY 37 $1,626 NI........................

FOR USE WITH: 310-9391 CouplerFOR USE WITH: 950H II STANDARD LIFT machines

Machine serial number JLX, MXLFOR USE WITH: 962H II STANDARD LIFT machines

Machine serial number PCW & SSA







WT-MWL




950H & 962H COUPLER SUPPLY GROUPS (FUSION) (Cont.)


FOR USE WITH: 310-9391 CouplerFOR USE WITH: 950H II HIGH LIFT machines

Machine serial number JLX, MXLFOR USE WITH: 962H II HIGH LIFT machines

Machine serial number PCW & SSA

COUPLER HOOKS (FUSION)

W 317-5562 HOOK, BLANK 787 $2,046 NI......................................

Lane 1 Work Tool - Ships loose from Caterpillar Work Tool & ServicesW 315-6309 HOOK, FLAT BACK 409 $1,207 NI...................................

Lane 1 Work Tool - Ships loose from Caterpillar Work Tool & Services

COUPLER CONNECTOR LINES (FUSION)


Lane 1 Work Tool - Ships loose from Caterpillar Work Tools & ServicesREQUIRED: when coupler is used with hydraulic

tools that require 3rd valveFOR USE WITH: 950H/962H and 950G/962G series II machines

950H/G & 962H/G COUPLER TILT LINK (FUSION)

W 344-0976 LINK, TILT 198 $1,635 NI.........................................

FOR USE WITH: 310-9391 coupler on 962H/G series IIHIGH LIFT machines

FOR USE WITH: 310-9391 coupler on 950H/G series IIHIGH LIFT machines

PIPE AND POLE FORK


106"(2693mm) Carriage, 72"(1829mm) TinesINCLUDES: Connector linesREQUIRES: 3rd ValveTINE WIDTH: 8"(204mm)TINE THICKNESS: 3"(77mm)

PIPE AND POLE FORK (FUSION)


106"(2693mm) Carriage, 72"(1829mm) TinesINCLUDES: Connector linesREQUIRES: Fusion Coupler and 3rd ValveTINE WIDTH: 8"(204mm)TINE THICKNESS: 3"(77mm)







WT-MWL




950H/G & 962H/G MATERIAL HANDLING ARMS (FUSION)


Lane 1 Work ToolExtendable Length 123" (3124mm) to 183" (4648mm)

950H/G & 962H/G RAKES / PIN-ON

LOADER (PIN-ON)

W 157-3471 RAKE, LOADER 112" 3,350 $16,668 NI................................

RAKING WIDTH: 112"(2845mm)HEIGHT: 66"(1676mm)NUMBER OF TEETH: 9TOOTH SPACING: 12"(305mm)

950H/G & 962H/G RAKES / COUPLER /FUSION

W 317-1242 RAKE-GP, 120" (QC) 1,485 $16,668 NI................................

FOR USE WITH: Fusion CouplerRAKING WIDTH: 112"(2844mm)OVERALL WIDTH: 120"(3047mm)HEIGHT: 65"(1653mm)NUMBER OF TEETH: 9TOOTH SPACING: 11.75"(299mm)

W 317-1254 RAKE, LOADER 112" W/DTC 4,894 $29,638 NI..........................

FOR USE WITH: Fusion CouplerDOUBLE TOP CLAMPRAKING WIDTH: 112"(2844mm)OVERALL WIDTH: 120"(3047mm)HEIGHT: 74"(1875mm)NUMBER OF TEETH: 9TOOTH SPACING: 11.75"(299mm)REQUIRES: 3rd valve200-0724 kit is required for mounting on 950H/962H machines







WT-MWL



966 & 972 WHEEL LOADER

966 & 972 BUCKETS / PIN-ON

GENERAL PURPOSE PERFORMANCE SERIES - 966 ONLY (PIN-ON)

W 363-5194 BKT GP ST 126" 5.00YD3 PO 4,583 $16,960 NI.........................

PERFORMANCE SERIES BUCKETFOR USE WITH: 966M/K/H/G MachinesCAPACITIES:4.75YD3(3.6M3) w/bolt-on adapters, 130"(3307mm) wide5.00YD3(3.8M3) w/bolt-on adapters & segments, 130"(3307mm) wide5.00YD3(3.8M3) w/bolt-on cutting edge, 127"(3220mm) wide(Bucket Tag)110% FILL FACTOR:5.50YD3(4.2M3) w/bolt-on cutting edge, 127"(3220mm) wide(Bucket Tag)Requires GET: Choose one set of adaptors, one set of tips (8 qty)and optional bolt-on segmentsFor BOCE Arrangement - order bucket part: 516-2406

P 516-2406 BKTA GP ST 127" 5.00YD3 PO 5,187 $18,778........................

Lane 1 Work ToolFOR USE WITH: 966M/K/H/G MachinesINCLUDES: 363-5194 Bucket-GP with BOCE

W 368-4582 BKT GP ST 126" 5.25YD3 PO 4,691 $17,513 NI.........................

PERFORMANCE SERIES BUCKETFOR USE WITH: 966M/K/H/G MachinesCAPACITIES:5.00YD3(3.8M3) w/bolt-on adapters, 130"(3307mm) wide5.25YD3(4.0M3) w/bolt-on adapters & segments, 130"(3307mm) wide5.25YD3(4.0M3) w/bolt-on cutting edge, 127"(3220mm) wide(Bucket Tag)110% FILL FACTOR:5.75YD3(4.4M3) w/bolt-on cutting edge, 127"(3220mm) wide (Bucket Tag)Requires GET: Choose either bolt-on cutting edge with corner guard orone set of adaptors, one set of tips (8 qty) and optional bolt-onsegments

W 363-5196 BKT GP ST 126" 5.50YD3 PO 4,815 $18,111 NI.........................










WT-MWL




966 & 972 BUCKETS / PIN-ON (Cont.)

W 363-5197 BKT GP ST 126" 6.00YD3 PO 4,978 $19,204 NI.........................

PERFORMANCE SERIES BUCKETFOR USE WITH: 966M/K/H/G MachinesCAPACITIES:5.75YD3(4.4M3) w/bolt-on adapters, 130"(3307mm) wide6.00YD3(4.6M3) w/bolt-on adapters and segments, 130"(3307mm)6.00YD3(4.6M3) w/bolt-on cutting edges, 127"(3220mm) wide(Bucket Tag)110% FILL FACTOR:6.75YD3(5.1M3) w/bolt-on cutting edges, 127"(3220mm) wide(Bucket Tag)Requires GET: Choose either bolt-on cutting edge with corner guard orone set of adaptors, one set of tips (8 qty) and optional bolt-onsegments

GENERAL PURPOSE PERFORMANCE SERIES - 972 ONLY (PIN-ON)

W 330-2045 BKT GP ST 126" 5.50YD3 PO 4,782 $18,051 NI.........................

FOR USE WITH: 972M/K/H/G MachinesPERFORMANCE SERIES BUCKETCAPACITIES:5.25YD3(4.0M3) w/bolt-on adapters, 130"(3302mm) wide5.50YD3(4.2M3) w/bolt-on adapters & segments, 130"(3302mm) wide5.50YD3(4.2M3) w/bolt-on cutting edge, 127"(3226mm) wide(Bucket Tag)110% FILL FACTOR6.00YD3(4.6M3) w/bolt-on cutting edge, 127"(3226mm) wide(Bucket Tag)Requires GET: Choose either bolt-on cutting edge with corner guard orone set of adaptors, one set of tips (8 qty) and optional bolt-onsegments

W 354-4831 BKT GP ST 126" 6.00YD3 PO 4,907 $19,067 NI.........................

PERFORMANCE SERIES BUCKETFOR USE WITH: 972M/K/H/G MachinesCAPACITIES:5.75YD3(4.4M3) w/bolt-on adapters, 130"(3302mm) wide6.00YD3(4.6M3) w/bolt-on adapters & segments, 130"(3307mm) wide6.00YD3(4.6M3) w/bolt-on cutting edge, 127"(3226mm) wide(Bucket Tag)110% FILL FACTOR:6.75YD3(5.1M3) w/bolt-on cutting edge, 127"(3226mm) wide(Bucket Tag)Requires GET: Choose either bolt-on cutting edge with corner guard orone set of adaptors, one set of tips (8 qty) and optional bolt-onsegments







WT-MWL





W 348-6785 BKT GP ST 126" 6.25YD3 PO 5,026 $19,704 NI.........................



Lane 1 Work ToolFOR USE WITH: 972M/K/H/G MachinesINCLUDES: 348-6785 Bucket-GP with BOCE and Corner Guards

W 354-4834 BKT GP ST 126" 6.50YD3 PO 5,099 $20,263 NI.........................

PERFORMANCE SERIES BUCKETFOR USE WITH: 972M/K/H/G MachinesCAPACITIES:6.25YD3(4.8M3) w/bolt-on adapters, 130"(3307mm) wide6.50YD3(5.0M3) w/bolt-on adapters and segments, 130"(3307mm)6.50YD3(5.0M3) w/bolt-on cutting edges, 127"(3220mm) wide(Bucket Tag)110% FILL FACTOR7.25YD3(5.5M3) w/bolt-on cutting edges, 127"(3220mm) wide(Bucket Tag)Requires GET: Choose either bolt-on cutting edge with corner guard orone set of adaptors, one set of tips (8 qty) and optional bolt-onsegments

GENERAL PURPOSE-ABRASION PERFORMANCE SERIES BUCKET- 972 ONLY (PIN-ON)


PERFORMANCE SERIES BUCKETFOR USE WITH: 972M MachinesINCLUDES: Bolt-On Cutting Edge (BOCE)CAPACITIES:6.75YD3(5.1M3) w/bolt-on Cutting Edges110% FILL FACTOR:7.25 YD3 (5.6 M3) with bolt-on edges, 132" (3357MM) wide (bucket tag)REQUIRES: COUNTERWEIGHT, AGGREGATE







WT-MWL






PERFORMANCE SERIES BUCKETFOR USE WITH: 972G/H/K/L/MINCLUDES: Bolt-On Cutting Edge (BOCE)CAPACITIES:7.00YD3(5.3M3) w/bolt-on cutting edge, 132"(3357mm) wide (bucket tag)110% FILL FACTOR:7.50YD3(5.8M3) w/bolt-on cutting edge, 132"(3357mm) wide (bucket tag)REQUIRES: COUNTERWEIGHT, AGGREGATE


100% FILL FACTOR is rated at 5.5M3 with BOCE110% FILL FACTOR is rated at 6.1M3 with BOCEIncludes Bolt-on Cutting EdgeRequires: Counterweight, Aggregate

FLAT FLOOR PERFORMANCE SERIES - 966 ONLY (PIN-ON)

W 368-4583 BKT FF ST 126" 5.50YD3 PO 4,912 $18,283 NI.........................

PERFORMANCE SERIES BUCKETFOR USE WITH: 966M/K/H/G MachinesCAPACITIES:5.25 YD3(4.0M3) with bolt-on adapters, 130"(3307mm) wide5.50 YD3(4.0 M3) with bolt-on adapters & segments, 130"(3307mm) wide5.50 YD3(4.2 M3) with bolt-on cutting edge, 126"(3221mm) wide110% FILL FACTOR:6.00YD3(4.60M3) w/bolt-on cutting edges, 126"(3221mm) wideRequires GET: Choose either bolt-on cutting edge with corner guard orone set of adaptors, one set of tips (8 qty) and optional bolt-onsegments

W 380-9835 BKT FF ST 126" 5.75YD3 PO 5,009 $18,860 NI.........................

PERFORMANCE SERIES BUCKETFOR USE WITH: 966M/K/H/GCAPACITIES:5.50YD3(4.2M3) w/bolt-on adapters, 130"(3307mm) wide5.75YD3(4.4M3) w/bolt-on adapters and segments, 130"(3307mm)5.75YD3(4.4M3) w/bolt-on cutting edges, 127"(3220mm) wide(Bucket Tag)110% FILL FACTOR:6.24YD3(4.8M3) w/bolt-on cutting edges, 127"(3220mm) wide(Bucket Tag)Requires GET: Choose either bolt-on cutting edge with corner guard orone set of adaptors, one set of tips (8 qty) and optional bolt-onsegments







WT-MWL





W 363-5201 BKT FF ST 126" 6.00YD3 PO 5,108 $19,456 NI.........................


FLAT FLOOR PERFORMANCE SERIES - 972 ONLY (PIN-ON)

W 368-4580 BKT FF ST 126" 6.00YD3 PO 4,980 $19,208 NI.........................

PERFORMANCE SERIES BUCKETFOR USE WITH: 972M/K/H/G MachinesCAPACITIES:5.75YD3(4.4M3) w/bolt-on adapters, 130"(3307mm) wide6.00YD3(4.6M3) w/bolt-on adapters & segments, 130"(3307mm) wide6.00YD3(4.6M3) w/bolt-on cutting edge, 127"(3220mm) wide(Bucket Tag)110% FILL FACTOR:6.75YD3(5.1M3) w/bolt-on cutting edges, 127"(3220mm) wide (Bucket Tag)Requires GET: Choose one set of adaptors, one set of tips (8 qty)and optional bolt-on segmentsFor BOCE Arrangement - order bucket part: 516-1817

W 516-1817 BKTA FF ST 127" 6.00YD3 PO 5,584 $21,026 NI........................


W 361-4996 BKT FF ST 126" 6.75YD3 PO 5,243 $20,986 NI.........................


ROCK PERFORMANCE SERIES - 966 ONLY (PIN-ON)







WT-MWL





W 554-0034 BKT RSP ST 128" 4.50YD3 PO 5,022 $25,285 NI........................

100% FILL FACTOR is rated at 3.4M3 including GET110% FILL FACTOR is rated at 3.7M3 including GETWith spade base edge, K90 two strap adaptors.Requires GET: Choose set of tips with optional set of bolt-on segmentsand/or optional sidebar protectors.


Rated width and capacity of bucket including GET.With spade base edge, ADVANSYS90 two strap adaptors.Requires GET: Choose set of tips with optional set of bolt-on segmentsand/or optional sidebar protectors.

ROCK PERFORMANCE SERIES - 972 ONLY (PIN-ON)


PERFORMANCE SERIES BUCKETSpade EdgeFOR USE WITH: 972M/K/H/G Machines ONLY!!!CAPACITIES:5.00YD3(3.8M3) w/weld-on adptrs, 128"(3255mm) wide5.25YD3(4.0M3) w/weld-on adptrs & segments,128"(3255mm)wide-Bucket Tag110% FILL FACTOR:5.75YD3(4.4M3) w/weld-on adptrs & segments,128"(3255mm)wide-Bucket Tag

SLAG (PIN-ON)

W 343-8820 BKT SLG HD 128" 4.50YD3 PO 9,136 $45,669 NI........................

128"(3250mm) wideINCLUDES: (7) weld-on K110 double-strap adapters and (1) segment groupREQUIRES: (7) K110 tips

SPECIAL APPLICATION (PIN-ON)

P 384-5794 BKT IO XD 128" 3.75YD3 PO 5,584 $35,090.........................

5,584 $35,090 NICAPACITIES:2.8 m3 with bolt-on adapters2.95 m3 with bolt-on adapters & segments2.95 m3 with bolt-on cutting edge110% FILL FACTOR:3.3 m3 with GETs

MULTIPURPOSE (PIN-ON)







WT-MWL





W 385-2592 BKT MP ST 127" 4.0 YD3 PO 5,999 $32,804 NI.........................

127"(3226mm) wideREQUIRES: 3rd valveCAPACITIES:3.75YD3(2.9M3) with bolt-on adapters, 127"(3226mm) wide4.00YD3(3.1M3) with bolt-on adapters & segments, 127"(3226mm) wide4.00YD3(3.1M3) with bolt-on cutting edge, 127"(3226mm) wideRequires GET: Choose either bolt-on cutting edge with corner guard orone set of adaptors, one set of tips (8 qty) and optional bolt-onsegments

WASTE HANDLING (PIN-ON)

W 449-4381 BKT WTC ST 132" 6.5 YD3 PO 9,248 $36,969 NI........................

Waste Handling bucket with clamp for light sorting or dozingwhen fully open.132" (3357mm) wideREQUIRES: Bolt-on cutting steel edge 437-8813 or rubber edge 383-9845ALSO REQUIRES: 3rd ValveCAPACITIES:6.50YD3 with Bolt-on cutting edge

W 516-2131 BKTA WD ST 132" 8.50YD3 PO 7,048 $30,239 NI.......................

Dozing style bucket132" (3357mm) wideINCLUDES: STEEL BOLT-ON CUTTING EDGE (BOCE)CAPACITIES:8.50YD3 (6.5M3) with Bolt-on cutting edge24.00YD3 (18.3 M3) dozing capacity with Bolt-on cutting edge

W 516-2101 BKTA WD ST 131" 8.50YD3 PO 6,777 $31,514 NI.......................

Dozing style bucket132" (3357mm) wideINCLUDES: RUBBER BOLT-ON CUTTING EDGE (BOCE)CAPACITIES:8.50YD3 (6.5M3) with Bolt-on cutting edge24.00YD3 (18.3 M3) dozing capacity with Bolt-on cutting edge

W 516-2103 BKTA WLC ST 132" 9.75YD3 PO 7,513 $35,271 NI......................

Load and Carry style bucketINCLUDES: BOLT-ON CUTTING EDGE (BOCE)INCLUDES: Steel BOLT-ON CUTTING EDGE (BOCE)CAPACITIES:9.75YD3 with Bolt-on cutting edge







WT-MWL





W 516-2145 BKTA WLC ST 131" 9.75YD3 PO 7,242 $36,546 NI.......................

Load and Carry style bucketINCLUDES: BOLT-ON CUTTING EDGE (BOCE)INCLUDES: Rubber BOLT-ON CUTTING EDGE (BOCE)CAPACITIES:9.75YD3 with Bolt-on cutting edge

SIDE-DUMP (PIN-ON)

W 143-7202 BKTA SD ST 145" 4.75 YD3 PO 6,301 $33,982 NI.......................

145"(3683mm) wideINCLUDES: Bolt-on cutting edgeREQUIRES: 3rd valve

HIGH DUMP (PIN-ON)



132" (3350mm) wideINCLUDES: Bolt on cutting edgeREQUIRES: 3rd valve





WOODCHIP (PIN-ON)


W 553-9645 BKTA WC ST 155" 15.50YD3 PO 7,061 $37,535 NI......................

INCLUDES: Bolt on cutting edgeFOR USE WITH: 966 Aggregate Configuration including Counterweight







WT-MWL





W 553-9649 BKTA WC ST 155" 18.25 YD3 PO 7,412 $35,356 NI......................

INCLUDES: Bolt on cutting edgeFOR USE WITH: 972 Aggregate Configuration including Counterweight

COAL PERFORMANCE SERIES - 966 ONLY (PIN-ON)

W 363-5203 BKTA FF LM 136" 9.25YD3 PO 6,314 $27,763 NI........................

PERFORMANCE SERIES BUCKETFOR USE WITH: 966M/K/H/G MachinesINCLUDES: Bolt on cutting edgeCAPACITIES:9.00 CYD (6.9 CUM) with bolt-on adapters, 136"(3447mm) wide9.25 CYD (7.1 CUM) with bolt-on cutting edges, 136"(447mm) wide

COAL PERFORMANCE SERIES - 972 ONLY (PIN-ON)

W 361-5002 BKTA FF LM 136" 9.5 YD3 PO 7,028 $30,318 NI........................

PERFORMANCE SERIES BUCKETFOR USE WITH: 972M/K/H/G MachinesINCLUDES: Bolt on cutting edgeCAPACITIES:9.50 YD3 (7.2 M3) with bolt-on cutting edges, 136"(447mm) wide

966 & 972 BUCKETS / COUPLER / FUSION

GENERAL PURPOSE PERFORMANCE SERIES - 966 ONLY (FUSION)









WT-MWL




966 & 972 BUCKETS / COUPLER / FUSION (Cont.)


PERFORMANCE SERIES BUCKETFOR USE WITH: 966M/K/H/GCAPACITIES:5.25YD3(4.0M3) w/bolt-on adapters, 130"(3307mm) wide5.50YD3(4.2M3) w/bolt-on adapters and segments, 130"(3307mm)5.50YD3(4.2M3) w/bolt-on cutting edges, 127"(3220mm) wide(Bucket Tag)110% FILL FACTOR:6.00YD3(4.6M3) w/bolt-on cutting edges, 127"(3220mm) wide(Bucket Tag)Requires GET: Choose one set of adaptors, one set of tips (8 qty)and optional bolt-on segmentsFor BOCE Arrangement - order bucket part: 515-5842


Lane 1 Work ToolINCLUDES: 362-9276 Bucket-GP with BOCE



GENERAL PURPOSE PERFORMANCE SERIES - 972 ONLY (FUSION)


PERFORMANCE SERIES BUCKETFOR USE WITH: 972M/K/H/G MachinesCAPACITIES:5.25YD3(4.0M3) w/bolt-on adapters, 130"(3302mm) wide5.50YD3(4.2M3) w/bolt-on adapters and segments, 130"(3302mm)5.50YD3(4.2M3) w/bolt-on cutting edges, 127"(3226mm) wide(Bucket Tag)110% FILL FACTOR:Requires GET: Choose either bolt-on cutting edge with corner guard orone set of K90 adaptors, one set of tips (8 qty) and optional bolt-onsegments







WT-MWL










PERFORMANCE SERIES BUCKETFOR USE WITH: 972M/K/H/G MachinesCAPACITIES:6.00YD3(4.6M3) w/bolt-on adapters, 130"(3302mm) wide6.25YD3(4.8M3) w/bolt-on adapters and segments, 130"(3302mm)6.25YD3(4.8M3) w/bolt-on cutting edges, 127"(3226mm) wide(Bucket Tag)110% FILL FACTOR7.00YD3(5.3M3) w/bolt-on cutting edges, 127"(3226mm) wide(Bucket Tag)Requires GET: Choose either bolt-on cutting edge with corner guard orone set of adaptors, one set of tips (8 qty) and optional bolt-onsegments


PERFORMANCE SERIES BUCKETFOR USE WITH: 972M/K/H/G MachinesCAPACITIES:6.25YD3(4.8M3) w/bolt-on adapters, 130"(3307mm) wide6.50YD3(5.0M3) w/bolt-on adapters and segments, 130"(3307mm)6.50YD3(5.0M3) w/bolt-on cutting edges, 127"(3220mm) wide(Bucket Tag)110% FILL FACTOR:7.25YDR(5.5M3) w/bolt-on cutting edges, 127"(3220mm) wide(Bucket Tag)Requires GET: Choose either bolt-on cutting edge with corner guard orone set of adaptors, one set of tips (8 qty) and optional bolt-onsegments







WT-MWL





FLAT FLOOR PERFORMANCE SERIES - 966 ONLY (FUSION)





FLAT FLOOR PERFORMANCE SERIES - 972 ONLY (FUSION)




MULTIPURPOSE (FUSION)







WT-MWL





W 313-1398 BKTA MP ST 127" 4.0 YD3 FUS 6,140 $32,501 NI.......................


SIDE-DUMP (FUSION)



COAL PERFORMANCE SERIES - 972 ONLY (FUSION)

W 361-5003 BKTA FF LM 136" 9.50YD3 FUS 6,870 $29,413 NI.......................

PERFORMANCE SERIES BUCKETFOR USE WITH: 972M/K/H/G MachinesINCLUDES: Bolt on cutting edge

HIGH DUMP (FUSION)

For heavy duty applications such as waste or handlingheaping materials such as compost.


120"(3059mm) wideINCLUDES: Bolt on EdgeREQUIRES: 3rd valve

HIGH DUMP (FUSION)












WT-MWL







ROCK PERFORMANCE SERIES - 966 ONLY (FUSION)

W 554-0036 BKT RSP ST 128" 4.50YD3 FUS 4,716 $24,617 NI.......................

100% FILL FACTOR is rated at 3.4M3 including GET110% FILL FACTOR is rated at 3.7M3 including GETWith spade base edge, ADVANSYS A90 two strap adaptors.Requires GET: Choose set of tips with optional set of bolt-on segmentsand/or optional sidebar protectors.

WOODCHIP (FUSION)



FOR USE WITH: 966 Aggregate Configuration including CounterweightW 553-9651 BKTA WC ST 155" 18.25YD3 FUS 7,341 $41,878 NI......................

FOR USE WITH: 972 Aggregate Configuration including Counterweight

966 & 972 BUCKET G.E.T.

BOLT ON CUTTING EDGES


30mm thick (1 required)FOR USE WITH: 127" buckets


35mm thick (1 required)FOR USE WITH: Rock buckets only

W 140-6824 CUTTING EDGE, HEAVY DUTY 696 $2,056..........................

35mm thick (1 required)FOR USE WITH: 127" buckets


FOR USE WITH: 449-4381 BucketW 383-9845 CUTTING EDGE, BOLT-ON RUBBER 319 $4,810........................

FOR USE WITH: 449-4381 Bucket

ADVANSYS A90 GET







WT-MWL




966 & 972 BUCKET G.E.T. (Cont.)



W 135-9293 SEGMENT, BOLT ON 481 $1,597..................................

40mm thick (1 required)FOR USE WITH: Rock buckets only

W 338-0559 SEGMENTS, BOLT ON,HALF ARROW 619 $2,188......................

40mm thick, half arrow (1 required)FOR USE WITH: A90 adapters and tipsFOR USE WITH: Rock buckets only


FOR USE WITH: A90 adapters (8 required)W 505-4091 TIP, PENETRATION 19 $103....................................

FOR USE WITH: A90 adapters (8 required)W 505-3996 TIP, EXTRA DUTY 23 $126.....................................

FOR USE WITH: A90 adapters (8 required)W 505-3991 TIP, ABRASION, HEAVY DUTY 30 $146...........................


W 100-6667 SEGMENTS, BOLT ON, SET OF 7 162 $1,007........................

FOR USE WITH: 539-5795 ADAPTERS, TIP, BOLT-ON, A090

PROTECTORS

P 135-8245 PROTECTORS, SIDEBAR, SET OF 2 50 $444........................

(1 required)FOR USE WITH: Rock buckets only

966 & 972 COUPLER / FUSION


Lane 1 Work ToolREQUIRES: Coupler supply group if machine is not coupler ready(HIGH LIFT machines need tilt link 315-5743)FOR USE WITH: 966M/K/H & 972M/K/H

966M & 972M COUPLER SUPPLY GROUPS (FUSION)


FOR USE WITH: 310-9390 Coupler966M STANDARD LIFT machinesmachine serial number prefix KJP, LMM, EJA,DYC, B8P, P6C, FL2, L8R and R8D







WT-MWL




966M & 972M COUPLER SUPPLY GROUPS (FUSION) (Cont.)


FOR USE WITH: 310-9390 Coupler972M STANDARD LIFT machinesmachine serial number prefix A8P, GGN, LSJJPR, M5S, EDW, M8W and L8E


FOR USE WITH: 310-9390 Coupler966M/972M HIGH LIFT machinesmachine serial number prefix KJP, LMM, EJADYC, B8P, P6C, FL2, L8R and R8Dmachine serial number prefix A8P, GGN, LSJJPR, M5S, EDW, M8W, L8E

966L & 972L COUPLER SUPPLY GROUPS (FUSION)


FOR USE WITH: 310-9390 Coupler966L STANDARD LIFT machinesMachine serial number prefix FSL and FRS


FOR USE WITH: 310-9390 Coupler972L STANDARD LIFT machinesMachine serial number prefix YJW and RFB


FOR USE WITH: 310-9390 Coupler966L/972L HIGH LIFT machines966L Machine serial number prefix FSL and FRS972L Machine serial number prefix YJW and RFB

966K & 972K COUPLER SUPPLY GROUPS (FUSION)


FOR USE WITH: 310-9390 CouplerFOR USE WITH: 966K STANDARD LIFT Machines ONLY!!!

machine serial number TFS, PBG, A5S and NGX


FOR USE WITH: 310-9390 CouplerFOR USE WITH: 972K STANDARD LIFT Machines ONLY!!!

machine serial number prefix Z4W and PEM







WT-MWL




966M & 972M COUPLER SUPPLY GROUPS (FUSION) (Cont.)


FOR USE WITH: 310-9390 CouplerFOR USE WITH: 966K HIGH LIFT Machines

machine serial number prefix TFS, PBG, A5S and NGXFOR USE WITH: 972K HIGH LIFT Machines

machine serial number prefix Z4W and PEM

966H & 972H COUPLER SUPPLY GROUPS (FUSION)


FOR USE WITH: 972H STANDARD LIFT machinesmachine serial number A7D, A7G, A7J, GTA, LCC

FOR USE WITH: 966H STANDARD LIFT machinesmachine serial number A6D, A6G, A6J, RYF, TAL


FOR USE WITH: 972H HIGH LIFT machinesmachine serial number A7D, A7G, A7J, GTA, LCC

FOR USE WITH: 966H HIGH LIFT machinesmachine serial number A6D, A6G, A6J, RYF, TAL


FOR USE WITH: 310-9390 couplerFOR USE WITH: 966H/972H LRC STD LIFT machines

machine serial number prefix BJ6 and BS6machine serial number prefix WXZ and NPE


FOR USE WITH: 310-9390 Coupler950H/962H LRC HIGH LIFT machinesmachine serial number prefix BJ6 and BS6machine serial number prefix WXZ and NPE

COUPLER CONNECTOR LINES (FUSION)

W 394-7214 LINES GP-IMPLEMENT 3V&4V (QC) 37 $1,285 NI........................

REQUIRED: when coupler is used with hydraulictools that require 3rd and or 4th valveFOR USE WITH: 966M/972M machines







WT-MWL




COUPLER CONNECTOR LINES (FUSION) (Cont.)


Lane 1 Work ToolREQUIRED: when coupler is used with hydraulic

tools that require 3rd valveFOR USE WITH: 966M/K/H machines966L: machine serial number prefix FSL and FRS966M: machine serial number prefix KJP, LMM, EJA,

DYC, B8P, P6C,FL2, L8R and R8D

966K: machine serial number prefix TFS, PBG, A5S and NGX966H: machine serial number prefix A6G, A6J, RYF, TAL, BJ6, BS6966H: machine serial numbers A6D01937 and up

FOR USE WITH: 972M/K/H machines972M: machine serial number prefix A8P, GGN, LSJ, JPR,

M5S, EDW, L9S, M8W, L8E972K: machine serial number prefix Z4W and PEM972H: machine serial number prefix A7G, A7J, GTA, LCC, WXZ and NPE972H: machine serial number prefix A7D00729 and up972L: machine serial number prefix YJW and RFB

COUPLER HOOKS (FUSION)

W 317-5562 HOOK, BLANK 787 $2,046 NI......................................

Lane 1 Work Tool

W 315-6309 HOOK, FLAT BACK 409 $1,207 NI...................................

Lane 1 Work Tool

966 & 972 FORKS / PIN-ON

LOGGING (PIN-ON)

W 398-4960 FORK, LOGGING 63" 5,679 $40,444 NI................................

98" (2498mm) carriage and 63" (1609mm) tinesINCLUDES: Double Top Clamp, GET tips and connecting linesREQUIRES: 3rd valve

MILLYARD (PIN-ON)


(CWTS PRODUCT)96" (2419mm) carriage and 64" (1618mm) tinesINCLUDES: Millyard Top Clamp, GET tips and connecting linesREQUIRES: 3rd valve

MILLYARD POLE (PIN-ON)







WT-MWL




966 & 972 FORKS / PIN-ON (Cont.)


88" (2236mm) carriage and 66" (1677mm) tinesINCLUDES: Millyard Top Clamp, Roller tips and connecting linesREQUIRES: 3rd valve

W 390-6753 BUCKET-CU, 132" 8.00 YD3 4,379 $12,946 NI..........................

Slips on over Millyard Pole ForksFOR USE WITH: 422-4917

SORTING GRAPPLE (PIN-ON)

W 448-9058 FORK GP-GRAPPLE 48" 4,506 $45,313 NI..............................

77" (1943mm) carriage and 48" (1221mm) tinesINCLUDES: Top Clamp and connecting linesREQUIRES: 3rd valve

FORK CONNECTOR LINES (PIN ON)

W 321-7903 LINES, CONNECTOR 8 $164 NI....................................

REQUIRES: Quantity of twoFOR USE WITH: 966K machinesFOR USE WITH: 966H machines

machine serial numbers A6D01937 and upmachine serial numbers A6G03852 and up

FOR USE WITH: 972K machinesFOR USE WITH: 972H machines

machine serial numbers A7D00729 and upmachine serial numbers A7G01227 and up

W 255-3588 LINES, CONNECTOR 0 $158 NI....................................

REQUIRES: Quantity of twoFOR USE WITH: 966H machines

machine serial numbers A6D01936 and downmachine serial numbers A6G03851 and down966G series I and II

FOR USE WITH: 972H machinesmachine serial numbers A7D00728 and downmachine serial numbers A7G01226 and down972G series I and II

PALLET (PIN-ON)

W 143-7206 FORK, PALLET 2,710 $10,478 NI....................................

96"(2438mm) carriage and 48"(1219mm) swinging tinesTINE WIDTH: 7"(180mm)TINE THICKNESS: 3"(76.2mm)







WT-MWL




966 & 972 FORKS / PIN-ON (Cont.)

W 143-7207 FORK, PALLET 2,855 $11,367 NI....................................

96"(2438mm) carriage and 60"(1524mm) swinging tinesTINE WIDTH: 7"(180mm)TINE THICKNESS: 3.5"(90mm)

W 143-7208 FORK, PALLET 2,995 $13,572 NI....................................


W 159-3022 FORK, PALLET 3,140 $14,596 NI....................................


PIPE AND POLE FORK (PIN-ON)


120"(3048MM) Carriage, 96"(2439mm) TinesINCLUDES: Connector linesREQUIRES: 3rd valveTINE WIDTH: 8"(203mm)TINE THICKNESS: 3.5"(90mm)

966 & 972 FORKS / COUPLER / FUSION

LOG & LUMBER FORK (FUSION)


84" (2134mm) carriage and 60" (1524mm) tines















WT-MWL




966 & 972 FORKS / COUPLER / FUSION (Cont.)



MILLYARD / FUSION


92" (2324mm) carriage and 63" (1609mm) tinesINCLUDES: Millyard Top Clamp, GET tips and connecting linesREQUIRES: 3rd valve










W 520-7957 CARRIAGE GROUP, 96" 1,761 $8,000 NI..............................

Lane 1 Work Tool96"(2438mm) carriageFOR USE WITH: Fusion CouplerREQUIRES: TINE GROUP


108"(2743mm) carriageFOR USE WITH: Fusion CouplerREQUIRES: TINE GROUP







WT-MWL





W 520-7985 TINE GROUP, 48" 1,012 $4,013 NI..................................

INCLUDES: Right and Left offset tines.REQUIRES: Carriage Group 520-7957 or 520-7968TINE WIDTH: 7" (180mm)TINE THICKNESS: 3.5" (90mm)

W 520-7980 TINE GROUP, 60" 1,150 $5,276 NI..................................


W 520-7979 TINE GROUP, 72" 1,288 $6,786 NI..................................


W 520-7986 TINE GROUP, 84" 1,425 $9,425 NI..................................


W 520-7981 TINE GROUP, 96" 1,562 $11,714 NI..................................


PIPE AND POLE FORK (FUSION)


120"(3048mm) Carriage, 96"(2439mm) TinesINCLUDES: Connector linesREQUIRES: Fusion Coupler and 3rd ValveTINE WIDTH: 8"(204mm)TINE THICKNESS: 3.5"(89mm)

966 & 972 MATERIAL HANDLING ARMS (FUSION)


Lane 1 Work Tool - Ships loose from Caterpillar Work Tool & ServicesExtendable Length 123" (3124mm) to 183" (4648mm)







WT-MWL




966 & 972 RAKES / PIN-ON

LOADER (PIN-ON)

W 230-5849 RAKE, LOADER 4,670 $22,761 NI....................................

RAKING WIDTH: 124"(3150mm)HEIGHT: 66"(1676mm)NUMBER OF TEETH: 9TOOTH SPACING: 13"(330mm)

966 & 972 RAKES / COUPLER / FUSION

W 317-1243 RAKE, LOADER 124" 4,597 $22,763 NI................................

FOR USE WITH: Fusion CouplerRAKING WIDTH: 124"(3156mm)OVERALL WIDTH: 132"(3353mm)HEIGHT: 66"(1668mm)NUMBER OF TEETH: 9TOOTH SPACING: 13"(330mm)

966 & 972 SNOW REMOVAL / FUSION



BLADE HEIGHT: 42" (1067mm)REQUIRES: Fusion Coupler















WT-MWL




U/V ANGLE BLADES

W 524-6865 BLD 132 U/V ANG FUS 2,900 $29,628 NI..............................


TWO AVAILABLE HYDRAULIC FUNCTIONS (e.g. 3F & 4F)CANADIAN DEALERS REFERENCE WT-CADSNW PRICE LIST

W 524-6866 BLD 144 U/V ANG FUS 3,000 $33,332 NI..............................



W 524-6867 BLD 168 U/V ANG FUS 3,150 $37,035 NI..............................



SNOW PUSH


HEIGHT: 56" (1423mm)REQUIRES: Fusion CouplerCANADIAN DEALERS REFERENCE WT-CADSNW PRICE LIST





W 524-6875 BLD 360" SNOW PUSH FUS 10,859 $39,997 NI.........................

HEIGHT: 56" (1423mm)REQUIRES: Fusion Coupler

ICE SCRAPER









WT-MWL




V-PLOW (FUSION)

W 314-2511 PLOW, 126" V SNOW 2,917 $11,886 NI...............................

HEIGHT: 84" (2134MM)FOR USE WITH: FUSION COUPLER







WT-MWL



980H, 980K, 980L AND 980M WHEEL LOADER

980M / 980K / 980H / 980G BUCKETS

All 980H/980G buckets listed will fit both Standardand High Lift loader configurations. Materialdensity will determine appropriate capacitybucket. Refer to Specalog. Exceedingmaximum payload may cause loader instability.

PIN-ON BUCKETS


W 330-2047 BKT GP ST 134" 7.00YD3 PO 5,860 $22,804 NI.........................

PERFORMANCE SERIES BUCKETCAPACITIES:6.50YD3(5.0M3) w/bolt-on adapters, 139"(3531mm) wide7.00YD3(5.35M3) w/bolt-on adapters & segments, 139"(3531mm)wide7.00YD3(5.35M3) w/bolt-on cutting edge, 136"(3454mm) wide(Bucket Tag)110% FILL FACTOR:7.75YD3(5.8M3) w/bolt-on cutting edge, 136"(3454mm) wide(Bucket Tag)Requires GET: Choose one set of A100 adaptors, one set of tips (8 qty)and optional bolt-on segmentsFor BOCE Arrangement - order bucket part: 516-1626


Lane 1 Work ToolINCLUDES: 330-2047 Bucket-GP with BOCE and Corner Guards.

W 330-2048 BKT GP ST 134" 7.50YD3 PO 6,087 $24,306 NI.........................

PERFORMANCE SERIES BUCKETREQUIRES: Counterweight, AggregateCAPACITIES:7.00YD3(5.35M3) w/bolt-on adapters, 139"(3531mm) wide7.50YD3(5.7M3) w/bolt-on adapters & segments, 139"(3531mm) wide7.50YD3(5.7M3) w/bolt-on cutting edge, 136"(3454mm) wide (Bucket Tag)110% FILL FACTOR8.25YD3(6.3M3) w/bolt-on cutting edge, 136"(3454mm) wide (Bucket Tag)Requires GET: Choose one set of A100 adaptors, one set of tips (8 qty)and optional bolt-on segmentsFor BOCE Arrangement - order bucket part: 516-1378









WT-MWL



980H, 980K, 980L AND 980M WHEEL LOADER (CONT.)

980M / 980K / 980H / 980G BUCKETS (Cont.)

W 348-6786 BKT GP ST 134" 7.75YD3 PO 6,182 $25,029 NI.........................

PERFORMANCE SERIES BUCKETREQUIRES: Counterweight, AggregateCAPACITIES:7.50YD3(5.7M3) w/bolt-on adapters, 139"(3531mm) wide7.75YD3(6.0M3) w/bolt-on adapters & segments, 139"(3531mm) wide7.75YD3(6.0M3) w/bolt-on cutting edge, 136"(3454mm) wide(Bucket Tag)110% Fill Factor:8.75YD3(6.6M3) w/bolt-on cutting edge, 136"(3454mm) wide(Bucket Tag)Requires GET: Choose one set of A100 adaptors, one set of tips (8 qty)and optional bolt-on segmentsFor BOCE Arrangement - order bucket part: 515-5841




PERFORMANCE SERIES BUCKETINCLUDES: BOLT-ON CUTTING EDGE (BOCE) & CORNER GUARDSREQUIRES: Counterweight, AggregateCAPACITIES:8.25YD3(6.4M3) w/bolt-on cutting edge, 137"(3481mm) wide(Bucket Tag)110% Fill Factor:9.25YD3(7.0M3) w/bolt-on cutting edge, 137"(3481mm) wide(Bucket Tag)

GENERAL PURPOSE ABRASION (PIN-ON)


PERFORMANCE SERIES BUCKETINCLUDES: ARM BOLT-ON CUTTING EDGE (BOCE) & CORNER GUARDSREQUIRES: Aggregate Package CounterweightCAPACITIES:7.75YD3(6.0M3) w/bolt-on cutting edge, 137"(3481mm) wide(Bucket Tag)110% Fill Factor:8.75YD3(6.6M3) w/bolt-on cutting edge, 137"(3481mm) wide(Bucket Tag)

HEAVY DUTY GENERAL PURPOSE (PIN-ON)







WT-MWL





W 494-2538 BKT GP HD 137" 7.50YD3 PO 7,736 $29,857 NI.........................

PERFORMANCE SERIES BUCKETCAPACITIES:7.50YD3(5.7M3) w/bolt-on adapters & segments, 137"(3481mm)wide7.50YD3(5.7M3) w/bolt-on cutting edges, 137"(3481mm) wide(Bucket Tag)110% FILL FACTOR:8.25YD3(6.3M3) w/bolt-on cutting edges, 137"(3481mm) wide(Bucket Tag)INCLUDES: Sidebar protectorsRequires GET: Choose one set of A100 adaptors, one set of tips ( qty)and optional bolt-on segmentsFor BOCE Arrangement - order bucket part: 518-8291

W 518-8291 BKTA GP HD 137" 7.50YD3 PO 9,107 $34,082 NI........................

PERFORMANCE SERIES BUCKETLane 1 Work ToolINCLUDES: 494-2538 BUCKET w/BOCE, corner guards, & sidebar protectors

FLAT FLOOR PERFORMANCE SERIES BUCKETS PIN-ON

FLAT FLOOR, STANDARD

W 361-4998 BKT FF ST 134" 7.50YD3 PO 6,142 $24,435 NI.........................

PERFORMANCE SERIES BUCKETCAPACITIES:7.25YD3(5.5M3) w/bolt-on adapters, 139"(3535mm) wide7.50YD3(5.7M3) w/bolt-on adapters & segments, 139"(3535mm)wide7.50YD3(5.7M3) w/bolt-on cutting edges, 136"(3447mm) wide(Bucket Tag)110% FILL FACTOR:8.25YD3(6.3M3) w/bolt-on cutting edges, 136"(3447mm) wide(Bucket Tag)Requires GET: Choose one set of A100 adaptors, one set of tips (8 qty)and optional bolt-on segments nFor BOCE Arrangement - order bucket part: 462-9513

W 462-9513 BKTA FF ST 136" 7.50YD3 PO 7,176 $26,901 NI........................

Lane 1 Work ToolPERFORMANCE SERIES BUCKETINCLUDES: 361-4998 Bucket-GP with BOCE

W 361-5004 BKTA FF ST 143" 11.00YD3 PO 7,923 $36,061 NI.......................

PERFORMANCE SERIES BUCKET143"(3638mm) wideINCLUDES: bolt-on cutting edge

ROCK BUCKETS (PIN-ON)







WT-MWL





W 554-0044 BKT RSP AB 139" 7.00YD3 PO 7,769 $43,392 NI........................

PERFORMANCE SERIES BUCKETRated width and capacity of bucket including GET.With spade base edge, A100 two strap adapters.Requires GET: Choose set of tips with optional set of bolt-on segmentsand/or optional sidebar protectors.CANNOT BE USED WITH: COUNTERWEIGHT, AGGREGATE


PERFORMANCE SERIES SPADE EDGE BUCKETCANNOT BE USED WITH: Counterweight, AggregateCAPACITIES:4.2M3(5.50YD3) w/weld-on adapters, 3504mm(138") wide4.4M3(5.75YD3) w/weld-on adptrs & segments,3504mm(138")wide-Bucket Tag110% FILL FACTOR:4.8M3(6.25YD3) w/weld-on adptrs & segments,3504mm(138")wide-Bucket Tag

HEAVY DUTY QUARRY ROCK BUCKETSUse for bank or face loading 2700-2800 lbs/yd3material where high impact / high abrasion isencountered. Buckets include thicker base edge,four-piece liner package, inner & outer sidewear plates, bottom outside skid plates, hingebracket wear plates and base edge wear plates.Base edge ware plates included on Spade Edge.

W 260-1389 BKT RSP HD 138" 6.0 YD3 PO 8,049 $52,929 NI........................

SPADE EDGE.INCLUDES: (8) weld-on K110 H.D. double-strap adapters,(with A.R.M. on corner adapters), bolt-on half arrowsegments and (4) sidebar protectors.REQUIRES: 8-K110 tips.CANNOT BE USED WITH: COUNTERWEIGHT, AGGREGATE

SLAG (PIN-ON)

W 348-8565 BKT SLG HD 134" 5.00YD3 PO 11,689 $56,863 NI.......................

134"(3394mm) wideINCLUDES: (7) weld-on K130 double-strap adapters and (1) segment groupREQUIRES: (7) K130 heavy abrasion slag tips (309-1058 or 309-1059)

WASTE HANDLING (PIN ON)

980K







WT-MWL





W 517-2578 BKTA WD LM 153" 13.00YD3 PO 9,513 $49,636 NI......................

Dozing style bucket153" (3882 MM) wideCAPACITIES:13.00 YD3 (9.90M3) With BOCE32.00 YD3 (24.50M3) dozing capacity with BOCEINCLUDES: Steel BOCECANNOT BE USED WITH: COUNTERWEIGHT, AGGREGATE

W 516-1699 BKTA WD LM 150" 13.00YD3 PO 9,228 $51,558 NI......................

Dozing style bucket153" (3882 MM) wideCAPACITIES:13.00 YD3 (9.90M3) With BOCE32.00 YD3 (24.50M3) dozing capacity with BOCEINCLUDES: Rubber BOCECANNOT BE USED WITH: COUNTERWEIGHT, AGGREGATE

W 516-1756 BKTA WLC ST 153" 14.00YD3 PO 10,029 $56,496 NI.....................

Load and Carry style bucket153" (3882mm) wideCAPACITIES:14.00 YD3 (10.70M3) with bolt-on cutting edgeINCLUDES: Steel BOCE

W 516-1803 BKTA WLC ST 150" 14.00YD3 PO 9,744 $58,283 NI.....................

Load and Carry style bucket153" (3882mm) wideCAPACITIES:14.00 YD3 (10.70M3) with bolt-on cutting edgeINCLUDES: Rubber BOCE

WOODCHIP (PIN-ON)


W 195-2643 BKTA WC ST 164" 15.0 YD3 PO 8,792 $48,933 NI.......................

164"(4166mm) wideMAXIMUM MATERIAL DENSITY: 1230 lbs/yd3 (760kg/m3)INCLUDES: bolt-on cutting edgeFOR USE WITH: machine serial numbers 2KR04553 and up

machine serial numbers 9CM02126 and upmachine serial numbers AWH00234 and upgrease pin linkage







WT-MWL





W 553-9653 BKTA WC ST 175" 19.00YD3 PO 10,582 $54,564 NI.....................

INCLUDES: Bolt on cutting edgeFOR USE WITH: 980 AGG Configuration including Counterweight

COUPLER BUCKETS

GENERAL PURPOSE PERFORMANCE SERIES (FUSION)


PERFORMANCE SERIES BUCKETCAPACITIES:6.50YD3 (5.0M3) with bolt-on adapters, 139"(3351mm) wide7.00YD3 (5.4M3) with bolt-on adapters and segments, 139"(3351mm) wide7.00YD3 (5.4M3) with bolt-on cutting edges, 136"(3454mm) wide110% FILL FACTOR:7.75YD3 (5.9M3) with bolt-on cutting edges, 136"(3454mm) wide


Includes BOCE and corner guards.PERFORMANCE SERIES BUCKETCAPACITIES:7.00YD3 (5.4M3) with bolt-on adapters, 139"(3351mm) wide7.50YD3 (5.7M3) with bolt-on adapters and segments, 139"(3351mm) wide7.50YD3 (5.7M3) with bolt-on cutting edges, 136"(3454mm) wide110% FILL FACTOR:8.25YD3 (6.3M3) with bolt-on cutting edges, 136"(3454mm) wide

WOODCHIP (FUSION)


INCLUDES: Bolt on cutting edgeFOR USE WITH: 980 AGG Configuration including Counterweight


980M / 980K / 980H / 980G BUCKET G.E.T.

980M/980K/980H/980G BOLT ON CUTTING EDGES & CORNER GUARDS


35mm thick w/40mm endbits (1 required)W 127-0718 CUTTING EDGE, BOLT-ON 1,013 $2,753............................

40mm thick w/45mm endbits (1 required)Use for high abrasion application

W 229-6959 CUTTING EDGE, BOLT-ON HA 992 $3,150...........................

44MM thick w/48mm end bits (1 required)







WT-MWL




980M / 980K / 980H / 980G BUCKET G.E.T. (Cont.)

W 439-0497 CUTTING EDGE, BOLT-ON 1,004 $2,704............................

FOR USE WITH: Base edge 194-0659W 437-0206 CUTTING EDGE, BOLT-ON RUBBER 369 $5,553........................

FOR USE WITH: Base edge 194-0659W 174-7950 GUARD, CORNER 139 $1,076.....................................

FOR USE WITH: General Purpose Buckets withBolt-On Cutting Edges only.

G.E.T.

W 109-9059 SEGMENTS, BOLT ON,SET OF 7 395 $1,385.........................

30mm Thick (1 required)FOR USE WITH: A100 adapters and tips

W 135-9667 SEGMENTS, HD, BOLT-ON SET OF 7 560 $1,825.....................

45mm thick. (1 required)Use for high abrasion application.FOR USE WITH: A100 adapters and tips

W 119-3230 SEGMENTS, BOLT-ON, SET OF 7 653 $2,171........................

35mm thick (1 required)FOR USE WITH: Spade edge, A100 adapters and tips

W 107-3498 SEGMENTS, BOLT ON (HEAVY DUTY) 846 $2,710....................

45mm thick, (1 required)FOR USE WITH: Spade edge, A100 adapters & tips

W 109-3123 SEGMENTS,H.A.,BOLT-ON,SET OF 7 731 $1,657......................

45mm thick, half arrow (1 required)FOR USE WITH: Spade edge, A100 adapters & tips

W 539-5705 ADAPTER, ADVANSYS 100 304 $3,826.............................


W 505-4002 TIP, HEAVY DUTY ADVANSYS 30 $150...........................

FOR USE WITH: A100 adapters (8 required)W 505-4101 TIP, PENETRATION ADVANSYS 24 $131...........................

FOR USE WITH: A100 adapters (8 required)W 505-4004 TIP, GENERAL PURPOSE ADVANSYS 26 $142.......................

FOR USE WITH: A100 adapters and tips (8 required)W 505-4000 TIP, HEAVY PENETRAION ADVANSYS 37 $194......................

ONLY FOR USE WITH: A100 adapters (8 required)W 505-4103 TIP, PENETRATION PLUS ADVANSYS 28 $142......................

FOR USE WITH: A100 adapters (8 required)W 505-4001 TIP, HEAVY ABRASION 37 $154.................................


PROTECTORS

W 106-0912 PROTECTORS, SIDEBAR, SET OF 2 441 $850.......................

FOR USE WITH: Rock Buckets OnlyW 135-8245 PROTECTORS, SIDEBAR, SET OF 2 50 $444........................

(1 required)FOR USE WITH: Rock Buckte only







WT-MWL




980M / 980K / 980H / 980G BUCKET G.E.T. (Cont.)

W 357-2691 PROTECTORS, SIDEBAR, SET OF 4 159 $1,293.......................

(1 required)FOR USE WITH: Heavy Duty GP Buckets

Advansys 110


45mm thick, (1 required)FOR USE WITH: A110 adapters and tips


FOR USE WITH: A110 adapters (8 required)W 505-4111 TIP PENETRATION ADVANSYS 29 $168............................

FOR USE WITH: A110 adapters (8 required)W 505-4014 TIP, GENERAL DUTY 32 $158...................................

FOR USE WITH: A110 adapters (8 required)W 505-4010 TIP, HEAVY PENETRATION 47 $256..............................

FOR USE WITH: A110 adapters (8 required)W 505-4113 TIP, PENETRATION PLUS ADVANSYS 37 $196......................

FOR USE WITH: A110 adapters (8 required)W 505-4011 TIP, HEAVY ABRASION 52 $268.................................


980H/G BOLT ON CUTTING EDGES


35mm thick w/40mm endbits (1 required)W 127-0718 CUTTING EDGE, BOLT-ON 1,013 $2,753............................

40mm thick w/45mm endbits (1 required)Use for high abrasion application

W 229-6959 CUTTING EDGE, BOLT-ON HA 992 $3,150...........................

44MM thick w/48mm end bits (1 required)







WT-MWL




980M/K/L COUPLERS / FUSION


Lane 1 Work Tool - Ships loose from Caterpillar Work Tools & ServicesFOR USE WITH:

980L STANDARD LIFT machinesmachine serial number prefix D8Z980M STANDARD LIFT machinesmachine serial number prefix KRS, MK2,N8T, MK3, MGD980K STANDARD LIFT machinesmachine serial number prefix W7K and GTZ

NOT FOR USE WITH:495-7529: 980M Std Lubrication Ar495-7531: 980M High Lift Lubrication Ar495-7532: 980M Steel Mill Lubrication Ar498-5641: 980M Logger Lubrication Ar


FOR USE WITH:980L/M HIGH LIFT machines980L HIGH LIFT machinesmachine serial number prefix D8Z980M HIGH LIFT machinesmachine serial number prefix KRS, MK2,N8T, MK3, MGD

NOT FOR USE WITH:495-7529: 980M Std Lubrication Ar495-7531: 980M High Lift Lubrication Ar495-7532: 980M Steel Mill Lubrication Ar498-5641: 980M Logger Lubrication Ar

980L/M COUPLER SUPPLY GROUPS (FUSION)


Lane 1 Work Tool - Ships loose from Caterpillar Work Tools & ServicesFOR USE WITH: 447-6627 Coupler

980M STANDARD LIFT machinesmachine serial number prefix KRS, MK2,N8T, MK3 and MGD980L STANDARD LIFT machinesmachine serial number prefix D8Z


FOR USE WITH: 538-8670 Coupler980M HIGH LIFT machinesmachine serial number prefix KRS, MK2,N8T, MK3, MGD980L HIGH LIFT machinesmachine serial number prefix D8Z







WT-MWL




980M/K/L COUPLERS / FUSION (Cont.)

W 575-9012 LINES GP-IMPLEMENT 3V (QC) 36 $749 NI...........................

FOR USE WITH: 447-6627 Coupler980M STANDARD LIFT and HIGH LIFT machinesmachine serial number prefix KRS, MK2, WW3, XDJ,N8T, MK3 and MGD980L STANDARD LIFT and HIGH LIFT machinesmachine serial number prefix D8Z

REQUIRED: when coupler is used with hydraulic toolsthat require 3rd valve.

980K COUPLER SUPPLY GROUPS (FUSION)


FOR USE WITH: 447-6627 Coupler980K STANDARD LIFT machinesmachine serial number prefix W7K and GTZ

W 447-3925 LINES GP-IMPLEMENT 3V 24 $749 NI................................


REQUIRED: when coupler is used with hydraulic toolsthat require 3rd valve.

W 494-6541 KIT, REWORK AUTOLUBE 5 $803 NI................................


REQUIRED: when machine has autolube

980H/980G FORKS

PIN-ON FORKS

PALLET FORKS (PIN ON)

W 473-9106 FORK, PALLET 72" 5,472 $19,576 NI.................................

108" (2751mm) carriage and 72" (1828mm) swinging tinesTINE WIDTH: 8" (203mm)TINE THICKNESS: 3.5" (89mm)Load capacity is dependent on machine/worktool configuration.Please consult load charts.

W 473-9104 FORK, PALLET 96" 5,983 $21,804 NI.................................

108" (2751mm) carriage and 96" (2438mm) swinging tinesTINE WIDTH: 8" (203mm)TINE THICKNESS: 3.5" (89mm)Load capacity is dependent on machine/worktool configuration.Please consult load charts.







WT-MWL




980H/980G FORKS (Cont.)

LOGGING

W 383-1822 FORK, LOGGING 7,015 $54,649 NI...................................

109"(2769mm) carriage and 72"(1829mm) tinesINCLUDES: Double top clamp, GET tips and connecting linesREQUIRES: 3rd valveINSIDE HEIGHT: 64"(1627mm)FOR USE WITH: 980G/H/M Machine with Logging Arrangement onlyFOR USE WITH: Grease pin linkageMachine serial numbers 2KR04553 and upMachine serial numbers 9CM02126 and upMachine serial numbers AWH00234 and up

MILLYARD

W 507-6128 FORK, MILLYARD 8,788 $57,125 NI..................................

109" (2769mm) carriage and 72"(1829mm) tinesINCLUDES: Millyard top clamp, GET tips and connecting linesREQUIRES: 3rd valveFOR USE WITH: ALL 980G/H/M Machine with Logging Arrangement onlyFOR USE WITH: 980GII Grease pin linkage machinesMachine serial numbers 2KR04553 and upMachine serial numbers 9CM02126 and upMachine serial numbers AWH00234 and up







WT-MWL





COUPLER FORKS











Lane 1 Work Tool - Ships loose from Caterpillar Work Tools & Services108"(2731mm) carriageFOR USE WITH: Fusion CouplerREQUIRES: TINE GROUPLoad capacity is dependent on machine/worktool configuration.Please consult load charts.


W 523-4200 TINE GROUP, 72" 1,592 $11,261 NI..................................

Lane 1 Work Tool - Ships loose from Caterpillar Work Tools & ServicesINCLUDES: Right and Left straight tines.REQUIRES: Carriage Group 523-4199TINE WIDTH: 9.8" (250mm)TINE THICKNESS: 3.4" (85mm)Load capacity is dependent on machine/worktool configuration.Please consult load charts.







WT-MWL





W 523-4201 TINE GROUP, 84" 1,911 $12,847 NI..................................


W 523-4202 TINE GROUP, 96" 2,147 $14,908 NI..................................


980 MATERIAL HANDLING ARM


Extendable length 128" (3247mm) to 188" (4771mm)

SNOW REMOVAL (FUSION)




ONE AVAILABLE HYDRAULIC FUNCTIONS (e.g. 3F)REQUIRES: Jumper lines



ONE AVAILABLE HYDRAULIC FUNCTIONS (e.g. 3F)REQUIRES: Jumper lines

U/V ANGLE BLADES

W 524-6866 BLD 144 U/V ANG FUS 3,000 $33,332 NI..............................









WT-MWL




U/V ANGLE BLADES (Cont.)

W 524-6867 BLD 168 U/V ANG FUS 3,150 $37,035 NI..............................



SNOW PUSH







W 524-6875 BLD 360" SNOW PUSH FUS 10,859 $39,997 NI.........................


ICE SCRAPER


980H/980G BLOCK HANDLING TOOLS

980H/980G COUPLERS

W 212-8241 COUPLER, BLOCK HANDLING 2,235 $22,097 NI..........................

REQUIRES: 222-5269 Coupler Lines GroupFOR USE WITH: Logging Arrangement Machines Only

980H/980G COUPLER SUPPLY GROUP


FOR USE WITH: Block Handling Tools Only







WT-MWL




980H/980G BLOCK HANDLING TOOLS (Cont.)

980H/980G FORKS







WT-MWL



982M WHEEL LOADER

982M BUCKETS


W 392-7022 BKT GP ST 140" 8.25YD3 PO 7,800 $26,406 NI.........................

PERFORMANCE SERIES BUCKETCAPACITIES:7.75YD3(5.9M3) w/bolt-on adapters, 144"(3665mm) wide8.25YD3(6.3M3) w/bolt-on adapters and segments, 144"(3665mm)wide8.25 YD3(6.3M3) w/bolt-on cutting edges, 142"(3602mm) wide(Bucket Tag)REQUIRED BY: COUNTERWEIGHT, AGGREGATE110% FILL FACTOR:9.25YD3(7.0M3) w/bolt-on cutting edges, 142"(3602mm) wide(Bucket Tag)Requires GET: Choose one set of A100 adaptors, one set of tips (8 qty)and optional bolt-on segmentsFor BOCE Arrangement - order bucket part: 516-1499


Lane 1 Work ToolINCLUDES: 392-7022 Bucket-GP with BOCE

GENERAL PURPOSE-ABRASION PERFORMANCE SERIES (PIN-ON)

W 416-6462 BKT GP AB 140" 9.25YD3 PO 8,157 $37,317 NI.........................

PERFORMANCE SERIES BUCKETCAPACITIES:8.75YD3(6.7M3) w/bolt-on adapters, 144"(3665mm) wide9.25YD3(7.0M3) w/bolt-on adapters and segments, 144"(3665mm)wide9.25YD3(7.0M3) w/bolt-on cutting edges, 142"(3602mm) wide(Bucket Tag)110% FILL FACTOR:10.00YD3(7.7M3) w/bolt-on cutting edges, 142"(3602mm) wide(Bucket Tag)REQUIRES: COUNTERWEIGHT, AGGREGATERequires GET: Choose one set of A100 adaptors, one set of tips (8 qty)and optional bolt-on segmentsFor BOCE Arrangement - order bucket part: 518-6135


Lane 1 Work Tool - Ships loose from Caterpillar Work Tool & ServicesINCLUDES: 416-6462 Bucket-GP with BOCE







WT-MWL



982M WHEEL LOADER (CONT.)

982M BUCKETS (Cont.)

W 416-6463 BKT GP AB 140" 9.75YD3 PO 8,433 $39,719 NI.........................

Lane 1 Work Tool - Ships loose from Caterpillar Work Tool & ServicesPERFORMANCE SERIES BUCKETCAPACITIES:9.50YD3(7.2M3) w/bolt-on adapters, 144"(3665mm) wide9.75 YD3(7.5M3) w/bolt-on adapters and segments, 144"(3665mm)wide9.75 YD3(7.5M3) w/bolt-on cutting edges, 142"(3602mm) wide(Bucket Tag)110% FILL FACTOR10.75YD3(8.3M3) w/bolt-on cutting edges, 142"(3602mm) wide(Bucket Tag)REQUIRED BY: COUNTERWEIGHT, AGGREGATEPlease consult with the Caterpillar Dealer Instructor and/orRegional System Application Specialist to ensure proper bucketsize based on target payloads, target material densities, andestimated bucket fill factors to prevent machine overloading.

W 416-6464 BKT GP AB 140" 10.75YD3 PO 8,843 $44,281 NI........................

PERFORMANCE SERIES BUCKETCAPACITIES:10.25YD3(7.9M3) w/bolt-on adapters, 144"(3665mm) wide10.75YD3(8.2M3) w/bolt-on adapters and segments, 144"(3665mm)wide10.75YD3(8.2M3) w/bolt-on cutting edges, 142"(3602mm) wide(Bucket Tag)110% FILL FACTOR11.75YD3(9.0M3) w/bolt-on cutting edges, 142"(3602mm) wide(Bucket Tag)REQUIRED BY: COUNTERWEIGHT, AGGREGATEPlease consult with the Caterpillar Dealer Instructor and/orRegional System Application Specialist to ensure proper bucketsize based on target payloads, target material densities, andestimated bucket fill factors to prevent machine overloading.

HEAVY DUTY GENERAL PURPOSE PERFORMANCE SERIES (PIN-ON)

W 396-4829 BKT GP HD 142" 9.75YD3 PO 9,771 $42,338 NI.........................

PERFORMANCE SERIES BUCKETCAPACITIES:9.25YD3(7.0M3) w/bolt-on adapters, 144"(3665mm) wide9.75YD3(7.5M3) w/bolt-on adapters and segments, 144"(3665mm)wide9.75YD3(7.5M3) w/bolt-on cutting edges, 142"(3602mm) wide(Bucket Tag)110% FILL FACTOR10.75YD3(8.3M3) w/bolt-on cutting edges, 142"(3602mm) wide(Bucket Tag)REQUIRED BY: COUNTERWEIGHT, AGGREGATEPlease consult with the Caterpillar Dealer Instructor and/orRegional System Application Specialist to ensure proper bucketsize based on target payloads, target material densities, andestimated bucket fill factors to prevent machine overloading.

W 518-6127 BKTA GP HD 143" 9.25YD3 PO 10,897 $43,744 NI.......................

Lane 1 Work ToolPERFORMANCE SERIES BUCKETINCLUDES: BOLT-ON CUTTING EDGE (BOCE), CORNER GUARDS, & SIDEBARPROTECTORS







WT-MWL





MATERIAL HANDLING-HEAVY DUTY PERFORMANCE SERIES (PIN-ON)

W 396-4825 BKT FF HD 142" 9.25YD3 PO 9,956 $41,263 NI.........................

PERFORMANCE SERIES BUCKETCAPACITIES: with bolt-on adapters8.75YD3(6.7M3) w/bolt-on adapters, 144"(3665mm) wide9.25YD3(7.0M3) w/bolt-on adapters and segments, 144"(3665mm)wide9.25YD3(7.0M3) w/bolt-on cutting edges, 142"(3602mm) wide(Bucket Tag)REQUIRED BY: COUNTERWEIGHT, AGGREGATE110% FILL FACTOR:10.00YD3(7.7M3) w/bolt-on cutting edges, 142"(3602mm) wide(Bucket Tag)

ROCK PERFORMANCE SERIES (PIN-ON)

W 557-9586 BKT RSP ST 144" 7.0 YD3 PO 8,878 $45,419 NI........................

PERFORMANCE SERIES SPADE EDGE BUCKETCAPACITIES:6.75YD3(5.1M3) w/weld-on adapters, 144"(3648mm) wide7.00YD3(5.4M3) w/weld-on adptrs & segments,144"(3648mm)wide-Bucket Tag110% FILL FACTOR7.75YD3(5.9M3) w/weld-on adptrs & segments,144"(3648mm)wide-Bucket TagCANNOT BE USED WITH: COUNTERWEIGHT, AGGREGATE

W 539-0404 BKT RSP XD 144" 7.00YD3 PO 9,967 $56,156 NI........................

PERFORMANCE SERIES SPADE EDGE BUCKETCAPACITIES:6.75 YD3 (5.1 M3) with weld-on adapters, 144"(3648mm) wide7.00 YD3 (5.4 M3) with weld-on adapters and segments, 144"(3648mm)widCANNOT BE USED WITH: COUNTERWEIGHT, AGGREGATE

W 559-8096 BKTA RSP XD 143" 7.00YD3 PO 10,390 $58,713 NI......................

Lane 1 Work ToolINCLUDES: 539-0404 Bucket-Rock and Tip, General Duty

W 557-9587 BKT RSP XD 143" 7.50YD3 PO 10,223 $60,056 NI.......................

PERFORMANCE SERIES SPADE EDGE BUCKETCAPACITIES:7.25 YD3 (5.6 M3) with weld-on adapters, 144"(3648mm) wide7.50 YD3 (5.8 M3) with weld-on adapters and segments, 144"(3648mm)wideCANNOT BE USED WITH: COUNTERWEIGHT, AGGREGATE

COAL (PIN-ON)

W 416-6478 BKTA FF LM 143" 11.50YD3 PO 9,958 $42,069 NI.......................

INCLUDES: Bolt-on cutting edge







WT-MWL





WASTE (PIN-ON)

W 416-6477 BKTA WD ST 153" 13.25YD3 PO 10,792 $42,308 NI.....................

Dozing style bucketCAPACITIES:13.25 YD3 (10.2 m3) with Bolt-on cutting edge38.50 YD3 (29.5 M3) Dozing capacity with Bolt-on cutting edgeINCLUDES: Bolt-on cutting edge

WOODCHIP (PIN-ON)


W 416-6476 BKTA WC ST 164" 15.75YD3 PO 10,318 $46,840 NI.....................

INCLUDES: Bolt-on cutting edgeW 553-9657 BKTA WC ST 175" 22.50YD3 PO 11,971 $68,290 NI.....................

INCLUDES: Bolt on cutting edge

982M BUCKET G.E.T.

FOR CWTS PRODUCT - BUCKET G.E.T. CAN ONLY BE ORDERED AS INSTALLEDAND WITH A BUCKET!!

W 9W-1479 CUTTING EDGE, BOLT-ON 932 $2,535..............................

35mm thick w/ 40mm endbits (1 required)FOR USE WITH: Base edge 4E-6085

W 442-8514 CUTTING EDGE, BOLT-ON 1,059 $3,204............................

40mm thick w/ 45mm endbits (1 required)Use for high abrasion applicationFOR USE WITH: Base edge 4E-6085

W 174-7950 GUARD, CORNER 139 $1,076.....................................

FOR USE WITH: GP and MH style buckets with Bolt-on Cutting Edges.

W 357-2691 PROTECTORS, SIDEBAR, SET OF 4 159 $1,293.......................

(1 required)FOR USE WITH: HD GP, HD MH and HD QUARRY ROCK buckets







WT-MWL




982M BUCKET G.E.T. (Cont.)

W 106-0912 PROTECTORS, SIDEBAR, SET OF 2 441 $850.......................

(1 required)FOR USE WITH: ROCK buckets only

A100 G.E.T.

W 539-5705 ADAPTER, ADVANSYS 100 304 $3,826.............................


W 9W-0818 SEGMENTS, BOLT ON, SET OF 7 355 $1,290........................

30mm Thick, (1 required)FOR USE WITH: A100 adapters and tips



W 505-4101 TIP, PENETRATION ADVANSYS 24 $131...........................


W 505-4004 TIP, GENERAL PURPOSE ADVANSYS 26 $142.......................


W 505-4000 TIP, HEAVY PENETRAION ADVANSYS 37 $194......................


W 505-4103 TIP, PENETRATION PLUS ADVANSYS 28 $142......................


W 505-4001 TIP, HEAVY ABRASION 37 $154.................................

FOR USE WITH: K100 adapters (8 required)

A110 G.E.T. ADVANSYS

FOR 982M ROCK BUCKETS ONLY

W 119-3230 SEGMENTS, BOLT-ON, SET OF 7 653 $2,171........................




W 109-3123 SEGMENTS,H.A.,BOLT-ON,SET OF 7 731 $1,657......................










WT-MWL




982M BUCKET G.E.T. (Cont.)

W 505-4111 TIP PENETRATION ADVANSYS 29 $168............................




W 505-4010 TIP, HEAVY PENETRATION 47 $256..............................


W 505-4113 TIP, PENETRATION PLUS ADVANSYS 37 $196......................


W 505-4011 TIP, HEAVY ABRASION 52 $268.................................


PACKING

PACKING CODES

0P-0210 PACK, DOMESTIC TRUCK 0 NC................................

0P-5812 PACK, EXPORT 0 NC........................................

W 0G-0007 CWTS CUSTOM PRODUCT ACC QUOTE 0 NC NI......................

Can only be used for ETO ordersPlease use the "NOTES" screen when ordering to mention the quotenumber and to specify the required product(s) as mentioned inthe quote.






caterpillar machine price list wt-mwl medium …

Documents