British Standards for ParticleboardPanel Guide produced by Wood Panel Industries Federation, Timber Trade Federation, TRADA & BRE & National Green Specification August 2006 According to the both the Panel Guide and NGS (National Green Specification) - an independent organisation partnered with the Building Research Establishment to provide information to those involved with Sustainable Construction - the current British Standard for specifying particleboard is BS EN 312:2003. BS EN 312:2003: Particleboards. Specifications There are various types of board defined in BS EN 312 which indicate the range of use conditions of particleboard, with common applications including flooring, kitchen units and worktops, furniture and shopfitting. The 2003 version of this standard, replaced the previous 1997 version of BS EN 312, which was issued in seven parts. BS EN 312 specifies the requirements for particleboards to be used in dry and humid conditions, as particleboard is not normally suitable for exterior applications. With the introduction of the 2003 version of this standard a new grade of particleboard was introduced. This new grade was termed P3 and is intended to be a moisture resistant non-load bearing board, which should reduce the risk of moisture failure compared with the alternative grade P2. The basic mechanical properties of particleboard are controlled by BS EN 312 and design characteristic values for use of the load-bearing grades with Eurocode 5 are given in BS EN 12369-1. According to the Panel Guide, Cement Bonded Particleboard manufactured in Europe must be specified in accordance with the European standard EN 634. The UK version of this standard is BS EN 634. This standard states that particleboard can be bonded with Ordinary Portland Cement (OPC) or with magnesium-based cements. This standard has two parts: BS EN 634-1: Cement-bonded particleboards Specifications Part 1: General Requirements BS EN 634-2: Cement-bonded particleboards Specifications Part 2: Requirements for OPC bonded particleboards for use in dry, humid and exterior conditions. The second part of this standard BS EN 634:2 relates only to Ordinary Portland Cement Cement Bonded Particleboard Board. These boards have a very high durability and are suitable for use in dry, humid or exterior conditions. Their high density gives them good acoustic and fire performance. They are used for flooring, modular buildings and applications where high durability is required. The Panel Guide also states that Cement Bonded Particleboard that is used in construction must, by law, comply with the Harmonised Standard for wood-based panels which is BS EN 13986.

British Standards Institute August 2006 Analysis of the British Standard Institutes listings have identified the following standards for Particleboard:Standard Number BS EN 1087-1:1995 BS EN 634-1:1995 BS EN 634-2:1997 BS EN 319:1993 BS EN 335-3:1996 BS EN 123691:2001 BS EN 14322:2004 BS EN 13986:2004 BS EN 317:1993 Title Particle boards. Determination of moisture resistance. Particle boards. Determination of moisture resistance. Boil test Cement-bonded particle boards. Specification. General requirements Cement-bonded particle boards. Specification. Requirements for OPC bonded particleboards for use in dry, humid and exterior conditions Particleboards and fibreboards. Determination of tensile strength perpendicular to the plane of the board Hazard classes of wood and wood-based products against biological attack. Application to wood-based panels Wood-based panels. Characteristic values for structural design. OSB, particleboards and fireboards Wood-based panels. Melamine faced boards for interior uses. Definition, requirements and classification Wood-based panels for use in construction. Characteristics, evaluation of conformity and marking Particleboards and fibreboards. Determination of swelling in thickness after Status Confirmed, Current Confirmed, Current Current, Work in Hand Current Current Current Current Current Confirmed, Current

immersion in water BS 6100-4.3:1984 Glossary of building and civil engineering terms. Forest products. Wood based panel products Eurocode 5. Design of timber structures. General. Common rules and rules for buildings Particleboards. Definition and classification Structural use of timber. Code of practice for permissible stress design, materials and workmanship Cement bonded particleboards. Determination of frost resistance Wood-based panels. Surface soundness. Test method Particleboards. Specifications Extruded particleboards. Specifications Cement-bonded particleboards. Definition and classification Cement-bonded particleboards. Determination of hard body impact resistance Oriented strand boards (OSB). Definitions, classification and specifications prEN 12869-1. Wood-based panels. Structural floor decking on joists. Part 1. Performance specifications prEN 12869-2. Wood-based panels. Structural floor decking on joists. Part 2. Performance requirements prEN 12870-1. Wood-based panels. Structural wall sheathing on studs. Part 1. Performance specifications ISO 17064. Wood-based panels. Fibreboard and particleboard. Vocabulary EN 300. Oriented strand boards (OSB). Definitions, classification and specifications BS EN 634-2. Cement-bonded particleboards. Specifications. Part 2. Requirements for OPC bonded particleboards for use in dry, humid and external conditions ISO 16893-1. Wood-based panels. Particleboard. Part 1. Classifications Current, Proposed for Confirmation, Work in Hand Current Current Current, Work in Hand Current Current Current Current Confirmed, Current Confirmed, Current Current, Work in Hand Current, Draft for Public Comment Current, Draft for Public Comment Current, Draft for Public Comment Current, Draft for Public Comment Current, Draft for Public Comment Current, Draft for Public Comment Current, Draft for Public Comment

BS EN 1995-11:2004 BS EN 309:2005 BS 5268-2:2002 BS EN 1328:1997 BS EN 311:2002 BS EN 312:2003 BS EN 14755:2005 BS EN 633:1994 BS EN 1128:1996 BS EN 300:1997 97/103065 DC 97/103066 DC 97/103067 DC 03/305686 DC 04/30113724 DC 05/30132017 DC

06/30146208 DC

British Standards for profile productsBritish Standards Institute June 2006 Due to the number of various products and varying names given to the types of products produced by Likov, analysis of the British Standards Institute was carried out by searching for key terms to describe Likov products. The following is a list of the key terms that were used to find British Standards which could be applicable to Likov products:

Search Terms: +bead +plasterStandard Number BS 6452-1:1984 Title Beads for internal plastering and dry lining. Specification for galvanized steel beads Status Current, Proposed for Confirmation Current

BS EN 13658-1:2005 Metal lath and beads. Definitions, requirements and test methods. Internal plastering

Search Terms: +construction +joint +fillerStandard Number Title Status

BS 6093:1993 06/30147091 DC

Code of practice for design of joints and jointing in building construction BS 6093. Design of joints and jointing in building construction. Guide

Current, Work in Hand Current, Draft for Public Comment

British Standards for bathroom productsThe Bathroom Manufacturers Association May 2006 The Bathroom Manufacturers Association (BMA) is the trade association for manufacturers of bathroom products trading in the UK. According to the Bathroom Manufacturers Association the main British Standards for shower heads are as follows: BSEN 1112: Shower outlets High Pressure BSEN 13904: Shower outlets Low Pressure BSEN 1113: Shower hoses High Pressure BSEN 13905: Shower hoses Low Pressure The Bathroom Manufacturers Association do not believe there are any British Standards in place for bathroom shelving, soap dishes and these type of bathroom accessories. British Standards Institute June 2006 Analysis of the British Institute website has identified the following British Standards for Towel rails, taps, and shower heads. British Standards for Towel Rails:Standard Number BS EN 60335-243:2003 04/30109592 DC Title Specification for safety of household and similar electrical appliances. Particular requirements for clothes dryers and towel rails. Part 2-43 Particular requirements for clothes dryers and towel rails IEC 60335-2-43 A1. Household and similar electrical appliances. Safety. Part 2-43. Particular requirements for appliances for clothes dryers and towel rails Status Current, Work in Hand Current, Draft for Public Comment

British Standards for Bathroom Taps:Standard Number BS 5412:1996 Title Specification for low-resistance single taps and combination tap assemblies (nominal size and ) suitable for operation at PN 10 max. and a minimum flow pressure of 0.01 MPa (0. 1 bar) Sanitary tapware. Automatic shut-off valves PN 10 Sanitary tapware. General technical specifications for single taps and mixer taps (nominal size 1/2) PN 10. Minimum flow pressure of 0.05 MPa (0.5 bar) Shower hoses for (PN 10) sanitary tapware Sanitary tapware. Thermostatic mixing valves (PN 10). General technical specification Sanitary tapware. Low pressure mechanical mixing valves. General technical specification Thermostatic mixing valves for use in care establishments Acoustics. Laboratory tests on noise emission from appliances and equipment used in water supply installations. Method of measurement Sanitary tapware. Low pressure thermostatic mixing valves. General technical specifications Sanitary tapware. General specifications for flow rate regulators Status Current

BS EN 816:1997 BS EN 200:1992 BS EN 1113:1997 BS EN 1111:1999 BS EN 1286:1999 BS 7942:2000 BS EN ISO 38221:1999 BS EN 1287:1999 BS EN 246:2003

Current Current, Work in Hand Current Current Current Current Current Current Current

BS EN 248:2002 BS EN 695:2005 BS EN 13904:2003 BS EN 13905:2003 BS EN 817:1998 96/105590 DC 02/101511 DC 05/30127036 DC

Sanitary tapware. General specification for electrodeposited coatings of Ni-Cr Kitchen sinks. Connecting dimensions Low resistance shower outlets for sanitary tapware Low resistance shower hoses for sanitary tapware Sanitary tapware. Mechanical mixers (PN 10). General technical specifications Specification for installations inside buildings conveying water for human consumption. Part 3. Pipe sizing (prEN 806-3) BS EN 200. Sanitary tapware. Single taps and combination taps (PN 10). General technical specification EN 817. Sanitary tapware. Mechanical mixers (PN 10). General technical specifications

Current Current Current Current Current, Work in Hand Current, Draft for Public Comment Current, Draft for Public Comment Current, Draft for Public Comment

British Standards for Shower Heads/Hoses:Standard Number BS 6340-4:1984 BS EN 1112:1997 BS EN 1113:1997 Title Shower units. Specification for shower heads and related equipment Shower outlets for (PN 10) sanitary tapware Shower hoses for (PN 10) sanitary tapware Status Current Current Current

British Standards for Security DoorsThe Door & Hardware Federation May 2006 The Door & Hardware Federation (DHF) was created by a merger between the Association of Building Hardware Manufacturers and the Door & Shutter Manufacturers Association. DHF represents the interests of manufacturers and installers of industrial, pedestrian and garage doors as well as manufacturers of locks and building hardware. The DHF has established six specialist groups: Building Hardware Group Drive & Control Group Garage Door Group Industrial Door Group Metal Doorset Forum Repair & Service Group

According to the DHF there are a number of standards which cover the products of Security Doors; Security Shutters; and Garage Doors, these include British and other standards and are as follows:Applicable British and other Standards BS 1245:1975 Specification for metal door frames (steel) BS 3621:2004 Thief resistant lock assemblies - Key egress BS 476-20:1987 Fire tests on building materials and structures. Method for determination of the fire resistance of elements of construction (general principles) BS 476-22:1987 Fire tests on building materials and structures. Methods for determination of the fire resistance of non-loadbearing elements of construction BS EN 12426:2000 Industrial, commercial and garage doors and gates. Air permeability. Classification BS EN 12427:2000 Industrial, commercial and garage doors and gates. Air permeability. Test method BS EN 12428:2000 Industrial, commercial and garage doors and gates. Thermal transmittance. Requirements for the calculation BS EN 12444:2001 BS EN 61000-6-2:2001 Electromagnetic compatibility (EMC). Generic standards. Immunity standard for industrial environments BS EN 60335-2-95:2001 Safety of electrical appliances Particular requirements for drives for vertically-moving garage doors BS EN 60335-2-97:2001 Safety of electrical appliances Particular requirements for drives for rolling shutters, awnings, blinds &c

BS 476-31.1:1983 Fire tests on building materials and structures. Methods for measuring smoke penetration through doorsets and shutter assemblies. Method of measurement under ambient temperature conditions BS 5588 Fire precautions in the design, construction and use of buildings. Various parts published from 1984 onwards. Some have now been withdrawn. See also DD 9999:2005 BS 6375-1:2004 Performance of windows and doors. Classification for weathertightness and guidance on selection and specification BS 6399-2:1997 Loading for buildings. Code of practice for wind loads BS 8220-1:2000 Guide for security of buildings against crime - Part 1 - Dwellings BS 8220-2:1995 Guide for security of buildings against crime - Part 2 - Offices and shops BS 8220-3:2004 Guide for security of buildings against crime - Part 3: Storage, industrial and distribution premises BS 8424:2004 Building hardware. Pull handles. Requirements and test methods BS 8621:2004 Thief resistant lock assemblies - Keyless egress BS EN 1125:1997 Panic exit devices operated by a horizontal bar BS EN 1154:1997 Controlled door closing devices BS EN 1155:1997 Electrically powered hold open devices for swing doors BS EN 1158:1997 Door coordinator devices BS EN 12046-2:2000 Doors - Operating forces - Test method BS EN 12051:2000 Door and window bolts

Industrial, commercial and garage doors and gates. Resistance to wind load. Testing and calculation BS EN 12445:2001 Industrial, commercial and garage doors and gates. Safety in use of power operated doors. Test methods BS EN 12453:2001 Industrial, commercial and garage doors and gates. Safety in use of power operated doors. Requirements BS EN 12489:2000 Industrial, commercial and garage doors and gates. Resistance to water penetration. Test method BS EN 12604:2000 Industrial, commercial and garage doors and gates. Mechanical aspects. Requirements BS EN 12605:2000 Industrial, commercial and garage doors and gates. Mechanical aspects. Test methods BS EN 12635:2002 Industrial, commercial and garage doors and gates. Installation and use BS EN 1294:2000 Door leaves - Behaviour under humidity variations BS EN 12978:2003 Industrial, commercial and garage doors and gates. Safety devices for power operated doors and gates. Requirements and test methods BS EN 1303:2005 Cylinders for locks BS EN 13241-1:2003 Industrial, commercial and garage doors and gates Product standard - Products w/out fire/smoke resistance BS EN 13724:2002 Apertures of private letter boxes and letter plates. Requirements and test methods BS EN 14600:2005

BS EN 61000-6-3:2001 Electromagnetic compatibility (EMC). Generic standards. Emission standard for residential, commercial and light-industrial environments DD 171:1987 Guide to specifying performance requirements for hinged or pivoted doors (including test methods) DD 9999:2005 Code of practice for fire safety in the design, construction and use of buildings DD CEN/TS 13126-1:2004 Fittings for windows - Common requirements DD CEN/TS 13126-10:2004 Fittings for windows - Arm balancing systems DD CEN/TS 13126-11:2004 Fittings for windows - Top hung projecting reversible hardware DD CEN/TS 13126-12:2004 Fittings for windows - Side hung projecting reversible hardware DD CEN/TS 13126-13:2004 Fittings for windows - Sash balances DD CEN/TS 13126-14:2004 Fittings for windows - Sash fasteners DD CEN/TS 13126-15:2004 Fittings for windows - Rollers DD CEN/TS 13126-16:2004 Fittings for windows - Fittings for lift and slide systems DD CEN/TS 13126-17:2004 Fittings for windows - Fittings for tilt and slide systems DD CEN/TS 13126-2:2004 Fittings for windows - Casement fastener handles DD CEN/TS 13126-3:2004 Fittings for windows - Fittings for espagnolette bolts DD CEN/TS 13126-4:2004 Fittings for windows - Espagnolette bolts

BS EN 12207:2000 Windows and doors - Air permeability Classification BS EN 12208:2000 Windows and doors - Watertightness Classification BS EN 12209:2003 Mechanically operated locks, latches and striking plates BS EN 12210:2000 Windows and doors - Resistance to windload - Classification BS EN 12211:2000 Windows and doors - Resistance to windload - Test method BS EN 12217:2003 Doors - Operating forces - Requirements and classification BS EN 12219:2000 Doors - Climatic Influences - Requirements and Classification BS EN 12320:2001 Padlocks and padlock fittings BS EN 12400:2002 Windows and pedestrian doors Mechanical durability - Requirements and Classification BS EN 12424:2000 Industrial, commercial and garage doors and gates. Resistance to wind load. Classification BS EN 12425:2000 Industrial, commercial and garage doors and gates. Resistance to water penetration. Classification

Doorsets and openable windows with fire-resisting and/or smoke control characteristics Requirements and classification BS EN 1522:2001 Windows, doors &c - Bullet resistance BS EN 1527:1998 Hardware for sliding doors and folding doors BS EN 1529:2001 Door leaves - Height, width, thickness and squareness BS EN 1530:2001 Door leaves - General and local flatness BS EN 1634-1:2000 Fire resistance tests for door and shutter assemblies BS EN 1634-3:2004 Fire resistance tests for door and shutter assemblies. Smoke control doors and shutters BS EN 1670:1998 Building hardware - Corrosion resistance BS EN 179:1997 Emergency exit devices

DD CEN/TS 13126-5:2004 Fittings for windows - Opening restrictors DD CEN/TS 13126-6:2004 Fittings for windows - Variable geometry stay hinges DD CEN/TS 13126-7:2004 Fittings for windows - Finger catches DD CEN/TS 13126-8:2004 Fittings for windows - Tilt & turn &c hardware DD CEN/TS 13126-9:2004 Fittings for windows - Pivot hinges DD ENV 1627:1999 Windows, doors, shutters. Burglar resistance. Requirements and classification DD ENV 1628:1999 Windows, doors, shutters. Burglar resistance. Test method for the determination of resistance under static loading DD ENV 1629:1999 Windows, doors, shutters. Burglar resistance. Test method for determination of resistance under dynamic loading DD ENV 1630:1999

BS EN 1906:2002 Lever handles and knob furniture BS EN 1935:2002 Single axis hinges BS EN 1991-1-4:2005 Eurocode 1. Actions on structures. General actions. Wind actions BS EN 60204-1:1998, IEC 60204-1:1997 Safety of machinery. Electrical equipment of machines. General requirements BS EN 60335-1:2002 Specification for safety of household and similar electrical appliances. General requirements BS EN 60335-2-103:2003 Safety of electrical appliances Particular requirements for drives for gates, doors and windows

Windows, doors, shutters. Burglar resistance. Test method for the determination of resistance to manual burglary attempts PAS 23-1:1999 General performance requirements for door assemblies. Single leaf, external door assemblies to dwellings PAS 24-1:1999 Enhanced security performance requirements for door assemblies. Single and double leaf, hinged external door assemblies to dwellings

British Standards Institute June 2006 Analysis of the British Standard Institutes listings have identified the following standards for Security Doors:Standard Number BS 82202:1995 BS 5357:1995 BS EN 1522:1999 BS EN 1523:1999 BS 82203:2004 BS 82201:2000 BS EN 12051:2000 BS EN 8171:2005 BS EN 12209:2003 BS EN 11431:2005 BS 3621:2004 PAS 24-1:1999 BS 565513:1995 BS EN 1125:1997 BS EN 179:1998 BS 2881:1989 99/104967 DC 99/104966 DC 03/102518 DC Title Guide for security of buildings against crime. Offices and shops Code of practice for installation of security glazing Windows, doors, shutters and blinds. Bullet resistance. Requirements and classification Windows, doors, shutters and blinds. Bullet resistance. Test method Guide for security of buildings against crime. Storage, industrial and distribution premises Guide for security of buildings against crime. Dwellings Building hardware. Door and window bolts. Requirements and test methods Safety rules for the construction and installation of lifts. Particular applications to passenger lifts and goods passenger lifts. Vandal resistant lifts Building hardware. Locks and latches. Mechanically operated locks, latches and locking plates. Requirements and test methods Secure storage units. Requirements, classification and methods of test for resistance to burglary. Safes, ATM safes, strongroom doors and strongrooms Thief resistant lock assemblies. Key egress Enhanced security performance requirements for door assemblies. Single and double leaf, hinged external door assemblies to dwellings Lifts and service lifts. Recommendations for vandal resistant lifts Building hardware. Panic exit devices operated by a horizontal bar. Requirements and test methods Building hardware. Emergency exit devices operated by a lever handle or push pad. Requirements and test methods Specification for cupboards for the storage of medicines in health care premises Building hardware. Electronically controlled emergency exit systems. Requirements and test methods (prEN 13637) Building hardware. Electronically controlled panic exit systems. Requirements and test methods (prEN 13633) BS EN 13637. Building hardware. Electrically controlled emergency exit systems for use on escape routes. Requirements and test methods Status Current Current Current Current Current Current Current Current Current Current Current Current Current, Superseded Current, Work in Hand Current, Work in Hand Confirmed, Current Current, Draft for Public Comment Current, Draft for Public Comment Current, Draft for Public Comment

British Standards for Security Shutters/Garage Doors:The Door & Hardware Federation May 2006 The Door & Hardware Federation (DHF) was created by a merger between the Association of Building Hardware Manufacturers and the Door & Shutter Manufacturers Association. DHF represents the interests of manufacturers and installers of industrial, pedestrian and garage doors as well as manufacturers of locks and building hardware. The DHF has established six specialist groups:

Building Hardware Group Drive & Control Group Garage Door Group Industrial Door Group Metal Doorset Forum Repair & Service Group

According to the DHF there are a number of standards which cover the products of Security Doors; Security Shutters; and Garage Doors, these include British and other standards and are as follows:Applicable British and other Standards BS 1245:1975 Specification for metal door frames (steel) BS 3621:2004 Thief resistant lock assemblies - Key egress BS 476-20:1987 Fire tests on building materials and structures. Method for determination of the fire resistance of elements of construction (general principles) BS 476-22:1987 Fire tests on building materials and structures. Methods for determination of the fire resistance of non-loadbearing elements of construction BS 476-31.1:1983 Fire tests on building materials and structures. Methods for measuring smoke penetration through doorsets and shutter assemblies. Method of measurement under ambient temperature conditions BS 5588 Fire precautions in the design, construction and use of buildings. Various parts published from 1984 onwards. Some have now been withdrawn. See also DD 9999:2005 BS 6375-1:2004 Performance of windows and doors. Classification for weathertightness and guidance on selection and specification BS 6399-2:1997 Loading for buildings. Code of practice for wind loads BS 8220-1:2000 Guide for security of buildings against crime - Part 1 - Dwellings BS 8220-2:1995 Guide for security of buildings against crime - Part 2 - Offices and shops BS 8220-3:2004 Guide for security of buildings against crime - Part 3: Storage, industrial and distribution premises BS EN 12426:2000 Industrial, commercial and garage doors and gates. Air permeability. Classification BS EN 12427:2000 Industrial, commercial and garage doors and gates. Air permeability. Test method BS EN 12428:2000 Industrial, commercial and garage doors and gates. Thermal transmittance. Requirements for the calculation BS EN 12444:2001 Industrial, commercial and garage doors and gates. Resistance to wind load. Testing and calculation BS EN 12445:2001 Industrial, commercial and garage doors and gates. Safety in use of power operated doors. Test methods BS EN 12453:2001 Industrial, commercial and garage doors and gates. Safety in use of power operated doors. Requirements BS EN 12489:2000 Industrial, commercial and garage doors and gates. Resistance to water penetration. Test method BS EN 12604:2000 Industrial, commercial and garage doors and gates. Mechanical aspects. Requirements BS EN 12605:2000 Industrial, commercial and garage doors and gates. Mechanical aspects. Test methods BS EN 12635:2002 Industrial, commercial and DD 9999:2005 Code of practice for fire safety in the design, construction and use of buildings DD CEN/TS 13126-1:2004 Fittings for windows - Common requirements DD CEN/TS 13126-10:2004 Fittings for windows - Arm balancing systems DD CEN/TS 13126-11:2004 Fittings for windows - Top hung projecting reversible hardware DD CEN/TS 13126-12:2004 Fittings for windows - Side hung projecting reversible hardware DD CEN/TS 13126-13:2004 Fittings for windows - Sash balances BS EN 61000-6-3:2001 Electromagnetic compatibility (EMC). Generic standards. Emission standard for residential, commercial and light-industrial environments DD 171:1987 Guide to specifying performance requirements for hinged or pivoted doors (including test methods) BS EN 61000-6-2:2001 Electromagnetic compatibility (EMC). Generic standards. Immunity standard for industrial environments BS EN 60335-2-95:2001 Safety of electrical appliances Particular requirements for drives for vertically-moving garage doors BS EN 60335-2-97:2001 Safety of electrical appliances Particular requirements for drives for rolling shutters, awnings, blinds &c

BS 8424:2004 Building hardware. Pull handles. Requirements and test methods BS 8621:2004 Thief resistant lock assemblies - Keyless egress BS EN 1125:1997 Panic exit devices operated by a horizontal bar BS EN 1154:1997 Controlled door closing devices BS EN 1155:1997 Electrically powered hold open devices for swing doors BS EN 1158:1997 Door coordinator devices

garage doors and gates. Installation and use BS EN 1294:2000 Door leaves - Behaviour under humidity variations BS EN 12978:2003 Industrial, commercial and garage doors and gates. Safety devices for power operated doors and gates. Requirements and test methods BS EN 1303:2005 Cylinders for locks BS EN 13241-1:2003 Industrial, commercial and garage doors and gates Product standard - Products w/out fire/smoke resistance BS EN 13724:2002

DD CEN/TS 13126-14:2004 Fittings for windows - Sash fasteners DD CEN/TS 13126-15:2004 Fittings for windows - Rollers DD CEN/TS 13126-16:2004 Fittings for windows - Fittings for lift and slide systems DD CEN/TS 13126-17:2004 Fittings for windows - Fittings for tilt and slide systems DD CEN/TS 13126-2:2004 Fittings for windows - Casement fastener handles DD CEN/TS 13126-3:2004 Fittings for windows - Fittings for espagnolette bolts DD CEN/TS 13126-4:2004 Fittings for windows - Espagnolette bolts DD CEN/TS 13126-5:2004 Fittings for windows - Opening restrictors DD CEN/TS 13126-6:2004

BS EN 12046-2:2000 Doors - Operating forces - Test method BS EN 12051:2000 Door and window bolts BS EN 12207:2000 Windows and doors - Air permeability Classification BS EN 12208:2000 Windows and doors - Watertightness Classification BS EN 12209:2003 Mechanically operated locks, latches and striking plates BS EN 12210:2000 Windows and doors - Resistance to windload - Classification BS EN 12211:2000 Windows and doors - Resistance to windload - Test method BS EN 12217:2003 Doors - Operating forces - Requirements and classification BS EN 12219:2000 Doors - Climatic Influences - Requirements and Classification BS EN 12320:2001 Padlocks and padlock fittings BS EN 12400:2002 Windows and pedestrian doors Mechanical durability - Requirements and

Apertures of private letter boxes and letter plates. Requirements and test methods BS EN 14600:2005 Doorsets and openable windows with fire-resisting and/or smoke control characteristics Requirements and classification BS EN 1522:2001 Windows, doors &c - Bullet resistance BS EN 1527:1998 Hardware for sliding doors and folding doors BS EN 1529:2001 Door leaves - Height, width, thickness and squareness BS EN 1530:2001 Door leaves - General and local flatness BS EN 1634-1:2000 Fire resistance tests for door and shutter assemblies BS EN 1634-3:2004 Fire resistance tests for door and shutter assemblies. Smoke control doors and shutters BS EN 1670:1998 Building hardware - Corrosion resistance BS EN 179:1997

Fittings for windows - Variable geometry stay hinges DD CEN/TS 13126-7:2004 Fittings for windows - Finger catches DD CEN/TS 13126-8:2004 Fittings for windows - Tilt & turn &c hardware DD CEN/TS 13126-9:2004 Fittings for windows - Pivot hinges DD ENV 1627:1999 Windows, doors, shutters. Burglar resistance. Requirements and classification DD ENV 1628:1999 Windows, doors, shutters. Burglar resistance. Test method for the determination of resistance under static loading DD ENV 1629:1999 Windows, doors, shutters. Burglar resistance. Test method for determination of resistance under dynamic loading

Classification BS EN 12424:2000 Industrial, commercial and garage doors and gates. Resistance to wind load. Classification BS EN 12425:2000 Industrial, commercial and garage doors and gates. Resistance to water penetration. Classification

Emergency exit devices BS EN 1906:2002 Lever handles and knob furniture BS EN 1935:2002 Single axis hinges BS EN 1991-1-4:2005 Eurocode 1. Actions on structures. General actions. Wind actions BS EN 60204-1:1998, IEC 60204-1:1997 Safety of machinery. Electrical equipment of machines. General requirements BS EN 60335-1:2002 Specification for safety of household and similar electrical appliances. General requirements BS EN 60335-2-103:2003 Safety of electrical appliances Particular requirements for drives for gates, doors and windows

DD ENV 1630:1999 Windows, doors, shutters. Burglar resistance. Test method for the determination of resistance to manual burglary attempts PAS 23-1:1999 General performance requirements for door assemblies. Single leaf, external door assemblies to dwellings PAS 24-1:1999 Enhanced security performance requirements for door assemblies. Single and double leaf, hinged external door assemblies to dwellings

British Standards Institute June 2006 Analysis of the British Standard Institutes listings have identified the following standards for Shutters/Grilles: Standard Number BS 476-31.1:1983 Title Fire tests on building materials and structures. Methods for measuring smoke penetration through doorsets and shutter assemblies. Method of measurement under ambient temperature conditions Fire tests on building materials and structures. Methods for determination of the fire resistance of non-loadbearing elements of construction Windows, doors, shutters and blinds. Bullet resistance. Test method Fire resistance tests for door and shutter assemblies. Fire doors and shutters Shutters, external and internal blinds. Misuse. Test methods Shutters and blinds. Additional thermal resistance. Allocation of a class of air permeability to a product Windows, doors and shutters. Explosion resistance. Requirements and classification. Shock tube Windows, doors and shutters. Explosion resistance. Test method. Shock tube Shutters, external blinds, internal blinds. Terminology, glossary and definitions Blinds and shutters. Resistance to repeated operations (mechanical endurance). Methods of testing Blinds and shutters. Suitability for use of tubular and square motorizations. Requirements and test methods Status Current

BS 476-22:1987 BS EN 1523:1999 BS EN 1634-1:2000 BS EN 12194:2000 BS EN 13125:2001 BS EN 131231:2001 BS EN 131241:2001 BS EN 12216:2002 BS EN 14201:2004 BS EN 14202:2004

Current Current Current Current Current Current Current Current Current Current

BS EN 14203:2004 BS EN 13330:2002 BS EN 1634-3:2004 BS EN 124124:2003 BS EN 13659:2004 BS EN 12833:2001 BS EN 131232:2004 BS EN 131242:2004 BS EN 14759:2005 DD ENV 1630:1999 DD ENV 1627:1999 BS EN 13527:2000 BS EN 12045:2000 BS EN 1932:2001 BS EN ISO 100772:2003 BS EN 14501:2005 DD ENV 1629:1999 DD ENV 1628:1999 BS EN 1522:1999 BS EN 124122:2003 BS EN 60335-297:2001

Blinds and shutters. Capability for use of gears with crank handle. Requirements and test methods Shutters. Hard body impact. Test method Fire resistance tests for door and shutter assemblies. Smoke control doors and shutters Thermal performance of windows, doors and shutters. Determination of thermal transmittance by hot box method. Roller shutter boxes Shutters. Performance requirements including safety Skylight and conservatory roller shutters. Resistance to snow load. Test method Windows, doors, and shutters. Explosion resistance. Requirements and classification. Range test Windows, doors and shutters. Explosion resistance. Test method. Range test Shutters. Acoustic insulation relative to airborne sound. Expression of performance Windows, doors, shutters. Burglar resistance. Test method for the determination of resistance to manual burglary attempts Windows, doors, shutters. Burglar resistance. Requirements and classification Shutters and blinds. Measurement of operating force. Test methods Shutters and blinds power operated. Safety in use. Measurement of the transmitted force External blinds and shutters. Resistance to wind loads. Method of testing Thermal performance of windows, doors and shutters. Calculation of thermal transmittance. Numerical method for frames Blinds and shutters. Thermal and visual comfort. Performance characteristics and classification Windows, doors, shutters. Burglar resistance. Test method for determination of resistance under dynamic loading Windows, doors, shutters. Burglar resistance. Test method for the determination of resistance under static loading

Current Current Current Current Current Current Current Current Current Current, Work in Hand Current, Work in Hand Current Current Current Current Current Current, Work in Hand Current, Work in Hand

Windows, doors, shutters and blinds. Bullet resistance. Requirements and Current classification Thermal performance of windows, doors and shutters. Determination of thermal transmittance by hot box method. Frames Specification for safety of household and similar electrical appliances. Particular requirements. Particular requirements for drives for rolling shutters, awnings, blinds and similar equipment. Part 2-97: Particular requirements for drives for rolling shutters, awnings, blinds and similar equipment Thermal performance of windows, doors and shutters. Calculation of thermal transmittance. Simplified method Fire tests. Smoke control door and shutter assemblies. Commentary on test method and test data application Exterior blinds. Resistance to load due to water accumulation. Test method Windows and curtain walling, doors, blinds and shutters. Determination of Current Current, Work in Hand

BS EN ISO 100771:2000 BS ISO TR 59252:1997 BS EN 1933:1999 BS EN 949:1999

Current, Work in Hand Current Current Current

the resistance to soft and heavy body impact for doors BS EN 12635:2002 BS EN 12978:2003 BS EN 123651:2003 BS EN 123652:2003 BS EN 123653:2003 BS EN 123654:2003 BS EN 12453:2001 BS 8220-2:1995 BS EN 12605:2000 03/115061 DC Industrial, commercial and garage doors and gates. Installation and use Industrial, commercial and garage doors and gates. Safety devices for power operated doors and gates. Requirements and test methods Building hardware. Gasket and weatherstripping for doors, windows, shutters and curtain walling. Performance requirements and classification Building hardware. Gasket and weatherstripping for doors, windows, shutters and curtain walling. Linear compression force test methods Building hardware. Gasket and weatherstripping for doors, windows, shutters and curtain walling. Deflection recovery test method Building hardware. Gasket and weatherstripping for doors, windows, shutters and curtain walling. Recovery after accelerated ageing test method Industrial, commercial and garage doors and gates. Safety in use of power operated doors. Requirements Guide for security of buildings against crime. Offices and shops Industrial, commercial and garage doors and gates. Mechanical aspects. Test methods ISO 3008. Fire resistance tests. Test method for fire resistance of doors and shutters Current Current Current Current Current Current

Current, Work in Hand Current Current, Work in Hand Current, Draft for Public Comment

03/102655 DC

EN 14648. Building hardware. Fittings for shutters. Requirements and test Current, Draft methods for Public Comment BS EN 1634-2. Fire resistance tests for door and shutter assemblies. Part 2. Fire door hardware. Building hardware for fire resisting doorsets and openable windows BS EN 14500. Blinds and shutters. Thermal and visual comfort. Test methods BS EN 12605. Industrial commercial and garage doors and gates. Mechanical aspects. Test methods BS EN 12453. Industrial commercial and garage doors and gates. Safety in use of power operated doors. Requirements prEN 15269-2. Extended application of test results for doorsets and shutter assemblies. For doors and shutters. Part 2. Steel hinged and pivoted doorsets IEC 60335-2-97 ED.2 A1. Household and similar electrical appliances. Safety. Particular requirements for drives for rolling shutters, awnings, blinds and similar equipment EN ISO 10077-1. Thermal performance of windows, doors and shutters. Calculation of thermal transmittance. Part 1. General EN 60335-2-97. Household and similar electrical appliances. Safety. Part 2-97. Particular requirements for drives for rolling shutters, awnings, blinds and similar equipment ISO 5925-1. Fire tests. Smoke control door and shutter assemblies. Part 1. Ambient and medium temperature leakage test procedure Current, Draft for Public Comment Current, Draft for Public Comment Current, Draft for Public Comment Current, Draft for Public Comment Current, Draft for Public Comment Current, Draft for Public Comment Current, Draft for Public Comment Current, Draft for Public Comment Current, Draft for Public Comment

04/19991935 DC

02/104377 DC

05/30076951 DC

05/30076959 DC

05/30093062 DC

03/317805 DC

04/30113929 DC

04/30116228 DC

05/30137099 DC

05/30137946 DC

EN 15269-1. Extended application of test results for fire resistance for Current, Draft doorsets and shutter assemblies. For doors and windows. Part 1. General for Public requirements for fire resistance Comment EN 15269-3. Extended application of test results for fire resistance for doorsets and shutter assemblies. For doors and shutters. Part 3. Timber hinged and pivoted doorsets prEN 1630. Burglar resistant construction products (not for precast concrete parts). Test method for the determination of resistance to manual burglary attempts prEN 1629. Burglar resistant construction products (not for precast concrete parts). Test method for the determination of resistance under dynamic loading prEN 1628. Burglar resistant construction products (not for precast concrete parts). Test method for the determination of resistance under static loading prEN 1627. Burglar resistant construction products (not for precast concrete parts). Requirements and classification Steel wire and wire products for fences. Steel wire welded mesh fencing Construction drawings. Representation of modular sizes, lines and grids Industrial, commercial and garage doors and gates. Installation and use Materials and articles in contact with foodstuffs. Catering containers. Dimensions of accessories and supports Current, Draft for Public Comment Current, Draft for Public Comment Current, Draft for Public Comment Current, Draft for Public Comment Current, Draft for Public Comment Current Current Current Confirmed, Current

05/30137949 DC

06/30146718 DC

06/30146719 DC

06/30146722 DC

06/30146723 DC

BS EN 102234:1998 BS EN ISO 8560:1999 BS EN 12635:2002 BS EN 631-2:1999

The British Standard Institute identifies the following standards for Garage Doors: Standard Number BS EN 124331:2000 BS EN 124332:2000 BS EN 12424:2000 BS EN 12425:2000 BS EN 12426:2000 BS EN 12427:2000 BS EN 12428:2000 BS EN 12635:2002 BS EN 12604:2000 BS EN 12453:2001 BS EN 12489:2000 Title Industrial, commercial, and garage doors and gates. Terminology. Types of doors Industrial, commercial, and garage doors and gates. Terminology. Parts of doors Industrial, commercial and garage doors and gates. Resistance to wind load. Classification Status Current Current Current

Industrial, commercial and garage doors and gates. Resistance to water Current penetration. Classification Industrial, commercial and garage doors and gates. Air permeability. Classification Industrial, commercial and garage doors and gates. Air permeability. Test method Industrial, commercial and garage doors and gates. Thermal transmittance. Requirements for the calculation Industrial, commercial and garage doors and gates. Installation and use Industrial, commercial and garage doors and gates. Mechanical aspects. Requirements Industrial, commercial and garage doors and gates. Safety in use of power operated doors. Requirements Current Current Current Current Current, Work in Hand Current, Work in Hand

Industrial, commercial and garage doors and gates. Resistance to water Current

penetration. Test method BS EN 12444:2001 BS EN 12978:2003 BS EN 132411:2003 BS EN 12605:2000 BS EN 60335-295:2001 BS EN 12445:2001 BS EN 60335-295:2004 96/108073 DC 96/108703 DC 05/30076926 DC 05/30076951 DC 05/30076956 DC 05/30076959 DC 03/317783 DC Industrial, commercial and garage doors and gates. Resistance to wind load. Testing and calculation Industrial, commercial and garage doors and gates. Safety devices for power operated doors and gates. Requirements and test methods Industrial, commercial and garage doors and gates. Product standard. Products without fire resistance or smoke control characteristics Industrial, commercial and garage doors and gates. Mechanical aspects. Test methods Specification for safety of household and similar electrical appliances. Particular requirements. Particular requirements for drives for vertically moving garage doors for residential use Industrial, commercial and garage doors and gates. Safety in use of power operated doors. Test methods Household and similar electrical appliances. Safety. Particular requirements for drivers for vertically moving garage doors for residential use prEN 12624. Industrial, commercial and garage doors and gates. Operational noise. Requirements and test methods Current Current Current Current, Work in Hand Current, Revised

Current, Work in Hand Current

Current, Draft for Public Comment

prEN 12652. Industrial, commercial and garage doors and gates. Sound Current, Draft for reduction. Requirements and classification Public Comment EN 12604. Industrial commercial and garage doors and gates. Mechanical aspects. Requirements BS EN 12605. Industrial commercial and garage doors and gates. Mechanical aspects. Test methods BS EN 12445. Industrial commercial and garage doors and gates. Safety in use of power operated doors. Test methods BS EN 12453. Industrial commercial and garage doors and gates. Safety in use of power operated doors. Requirements IEC 60335-2-95-A1 ED.2. Safety of household and similar electrical appliances. Particular requirements for drives for vertically moving garage doors for residential use Current, Draft for Public Comment Current, Draft for Public Comment Current, Draft for Public Comment Current, Draft for Public Comment Current, Draft for Public Comment

British Standards for Electric BoilersBritish Standards Institute June 2006 Analysis of the British Institute website has identified the following British Standards for Electric Boilers. Standard Number BS 1894:1992 BS EN 60335-263:1993 BS EN 60730-215:1996, IEC 60730-2-15:1994 Title Specification for design and manufacture of electric boilers of welded construction Specification for safety of household and similar electrical appliances. Particular requirements. Commercial electric water boilers and liquid heaters Specification for automatic electrical controls for household and similar use. Particular requirements. Automatic electrical water level sensing controls of the float or electrode-sensor type used in boiler applications. Section 2.15: Automatic electrical water level sensing controls controls of the flaot or electrode-sensor type used in boiler applications Status Current, Partially Replaced Current, Superseded Current, Work in Hand

BS 855:1990 BS EN 60335-215:1996, IEC 60335-2-15:1995 BS 749:1969 BS 2486:1997 BS EN 129528:2002 BS EN 60335-215:2002 BS 5986:1980 BS 68803:1988 BS 3456202.46:1990, EN 60335-2-46:1989 BS EN 14597:2005 BS ISO 1461711:2002 BS EN 129527:2002 BS 6880-2:1988 BS EN 60730-218:1999, IEC 60730-2-18:1997

Specification for welded steel boilers for central heating and indirect hot water supply (rated output 44 kW to 3 MW) Specification for safety of household and similar electrical appliances. Particular requirements. Appliances for heating liquids. Particular requirements for Appliances for heating liquids Specification for underfeed stokers Recommendations for treatment of water for steam boilers and water heaters Water-tube boilers and auxiliary installations. Requirements for firing systems for liquid and gaseous fuels for the boiler Specification for safety of household and similar electrical appliances. Particular requirements for appliances for heating liquids Specification for electrical safety and performance of gas fired space heating appliances with inputs 60 kW to 2 MW Code of practice for low temperature hot water heating systems of output greater than 45 kW. Installation, commissioning and maintenance Specification for safety of household and similar electrical appliances. Particular requirements. Specification for safety of household and similar electrical appliances. Particular requirements. Commercial electric steam cookers Temperature control devices and temperature limiters for heat generating systems Graphical symbols for diagrams. Devices for heat transfer and heat engines Water-tube boilers and auxiliary installations. Requirements for equipment for the boiler Code of practice for low temperature hot water heating systems of output greater than 45 kW. Selection of equipment

Current, Partially Replaced Current, Revised

Current Current Current Current Confirmed, Current Current

Current

Current Current Current, Work in Hand Current

Specification for automatic electrical controls for household and similar Current, Work in use. Particular requirements. Particular requirements for automatic Hand electrical water and air flow sensing controls, including mechanical requirements. Particular requirements forautomatic electrical water and air flow sensing controls, including mechanical requirements Specification for safety of household and similar electrical appliances. Particular requirements for commercial dispensing appliances and vending machines Safety of domestic gas appliances. Specification for combination boilers IEC 60730-2-15 ED.2. Automatic controls for household and similar use. Part 2-15. Particular requirements for automatic electrical water level sensing controls of the float or electrode-sensor type used in boiler applications BS EN 60730-2-15/prA11. Automatic electrical controls for household and similar use. Part 2-15. Particular requirements for automatic electrical water level sensing controls of the float or electrode-sensor type used in boiler applications EN 15456. Heating boilers. Electrical power consumption for heat generators. System boundaries. Measurements Current, Work in Hand Current, Obsolescent Current, Draft for Public Comment

BS EN 60335-275:2004 BS 5258-15:1990 03/117957 DC

04/30115376 DC

Current, Draft for Public Comment

06/30145467 DC

Current, Draft for Public Comment

British Standards for Metal Roofing

Metal Cladding & Roofing Manufacturers Association According to the Metal Cladding & Roofing Manufacturers Association there are currently no British Standards covering the stone coated metal tile product which Satjam manufacture. The only British Standard in place which relates to this type of product is a code of practice for cladding buildings BS 5427. BS 5427-1:1996 Code of practice for the use of profiled sheet for roof and wall cladding on buildings. Design In order to trade in the UK, Satjam may be required to meet British Standards with regards to the components of their tile product. That is, Satjam may be required to meet the British Standards set for the materials used for the tile for example regulations on the base metal, the coatings etc. RoofConsult May 2006 RoofConsult are an advisory service involved in the UK roofing and cladding industry. The British Standards, listed on the RoofConsult website, which relate most closely to the products produced by Satjam are those covering Sheeting and Cladding and those covering Metal Roofing. The Standards shown on the RoofConsult website are as follows: British Standards - Sheeting & Cladding CP 143 -1:1958 BS EN 494 :1994 BS EN 506 :2000 BS EN 508 -1:2000 BS EN 508 -2:2000 BS EN 508 -3:2000 el BS EN 1013 1:1998 L BS EN 1013 2:1999 BS EN 1013 3:1998 BS EN 1013 4:2000 BS EN 1013 5:2000 BS 5427 -1:1996 BS 8219 :2001 Code of practice for sheet roof and wall coverings. Aluminium, corrugated and troughed Fibre-cement profiled sheets and fittings for roofing. Product specification and test methods Roofing products from metal sheet. Specification for self-supporting products of copper or zinc sheet Roofing products from metal sheet. Specification for self-supporting products of steel, aluminium or stainless steel sheet. Steel Roofing products from metal sheet. Specification for self-supporting products of steel, aluminium or stainless steel sheet. Aluminium Roofing products from metal sheet. Specification for self-supporting products of steel, aluminium or stainless steel sheet. Stainless ste Light transmitting profiled plastic sheeting for single skin roofing. General requirements and test methods Light transmitting profiled plastic sheeting for single skin roofing. Specific requirements and test methods for sheets of glass fibre reinforced polyester resin (GRP) Light transmitting profiled plastic sheeting for single skin roofing. Specific requirements and test methods for sheets of polyvinyl chloride (PVC) Light transmitting profiled plastic sheeting for single skin roofing. Specific requirements, test methods and performance of polycarbonate (PC) sheets Light transmitting profiled plastic sheeting for single skin roofing. Specific requirements, test methods and performance of polymethylmethacrylate (PMMA) sheets Code of practice for the use of profiled sheet for roof and wall cladding on buildings Installation of sheet roof and wall coverings - Profiled fibre cement - Code of Practice.

BS EN 12152 :2002 Curtain Walling - Air permeability - Performance requirements and classifications

British Standards - Metal Roofing BS EN 501 :1994 BS EN 502 :2000 Roofing products from metal sheet. Specifications for fully supported roofing products of zinc sheet Roofing products from metal sheet. Specification for fully supported products of stainless

steel sheet BS EN 504 :2000 BS EN 505 :2000 BS EN 507 :2000 BS EN 988 :1997 BS 6915 :2001 BS EN 14782:2006 Roofing products from metal sheet. Specification for fully supported roofing products of copper sheet Roofing products from metal sheet. Specification for fully supported roofing products of steel sheet Roofing products from metal sheet. Specification for fully supported roofing products of aluminium Zinc and zinc alloys. Specification for rolled flat products for building Design and Construction of fully supported lead sheet roof and wall coverings. Code of practice Self-supporting metal sheet for roofing, external cladding and internal lining. Product specification and requirements

David George (RoofConsults Standards & Flat Roofing Materials Expert): Mr. George from RoofConsult has advised that as far as his records, and those of a colleague of his at BSI, shows there are no specific British or European standards for steel roof tiles. Mr. George recommended that the Czech companies approach a testing board such as the BBA to have their product tested in order to receive certification for selling in the UK. Alternatively he suggested they apply for an E-Tag in order to receive CE marking for the product.

British Standards Institute June 2006 Analysis of the British Standards Institute has identified the following British Standards for Satjams type of roofing products: British Standards for Roof Tiles:

Standard Number BS EN 126294:2001 BS EN 1304:2005 BS EN 539-1:2005 BS EN 491:2004 BS EN 539-2:1998 BS EN 490:2004 BS 8000-6:1990 BS EN 538:1994 BS EN 1024:1997 BS 5534:2003 BS EN 14437:2004 BS EN 137482:2004 DD CEN/TS 15087:2005 04/30099864 DC

Title Machines for the manufacture of constructional products from concrete and calciumsilicate. Safety. Concrete and tile making machines Clay roofing tiles and fittings. Product definitions and specifications Clay roofing tiles for discontinuous laying. Determination of physical characteristics. Impermeability test Concrete roofing tiles and fittings for roof covering and wall cladding. Test methods Clay roofing tiles for discontinuous laying. Determination of physical characteristics. Test for frost resistance Concrete roofing tiles and fittings for roof covering and wall cladding. Product specifications Workmanship on building sites. Code of practice for slating and tiling of roofs and claddings Clay roofing tiles for discontinuous laying. Flexural strength test Clay roofing tiles for discontinuous laying. Determination of geometric characteristics Code of practice for slating and tiling (including shingles) Determination of the uplift resistance of clay or concrete tiles for roofing. Roof system test method Terrazzo tiles. Terrazzo tiles for external use Determination of the uplift resistance of installed clay and concrete interlocking tiles for roofing. Test method for mechanical fasteners BS EN 539-2. Clay roofing tiles for discontinuous laying. Determination of physical characteristics. Part 2. Test for frost resistance EN 490 AMD 1. Concrete roofing tiles and fittings for roof covering and wall cladding. Product specifications

Status Current Current Current Current Current, Work in Hand Current, Work in Hand Confirmed, Current Current Current Current Current Current Current Current, Draft for Public Comment Current, Draft for Public Comment

05/30139071 DC

British Standards for Steel Roof Products:Standard Number BS 1494-1:1964 BS EN 5081:2000 BS EN 5082:2000 BS EN 5083:2000 BS EN 502:2000 BS EN 505:2000 CP 143-10:1973 BS 5950-6:1995 BS EN 14782:2006 Title Specification for fixing accessories for building purposes. Fixings for sheet, roof and wall coverings Roofing products from metal sheet. Specification for self-supporting products of steel, aluminium or stainless steel sheet. Steel Roofing products from metal sheet. Specification for self-supporting products of steel, aluminium or stainless steel sheet. Aluminium Roofing products from metal sheet. Specification for self-supporting products of steel, aluminium or stainless steel sheet. Stainless steel Roofing products from metal sheet. Specification for fully supported products of stainless steel sheet Roofing products from metal sheet. Specification for fully supported roofing products of steel sheet Code of practice for sheet roof and wall coverings. Code of practice for sheet roof and wall coverings. Galvanized corrugated steel. Metric units Structural use of steelwork in building. Code of practice for design of light gauge profiled steel sheeting Self-supporting metal sheet for roofing, external cladding and internall ining. Product specification and requirements Status Current Current Current Current Current Current Current, Proposed for Confirmation Current Current

BS 5950-7:1992 BS 5427-1:1996 BS 5950-9:1994 DD ENV 101692:1999 03/115371 DC

Structural use of steelwork in building. Specification for materials and workmanship: cold formed sections Code of practice for the use of profiled sheet for roof and wall cladding on buildings. Design Structural use of steelwork in building. Code of practice for stressed skin design Continuously organic coated (coil coated) steel flat products. Products for building exterior applications EN 14783. Fully supported metal sheet and strip for roof coverings and wall finishes

Current, Obsolescent Current Current Current Current, Draft for Public Comment

British Standards for Metal Roof Products:Standard Number BS EN 501:1994 BS EN 5081:2000 BS EN 5082:2000 BS EN 5083:2000 BS EN 507:2000 BS EN 505:2000 BS EN 504:2000 BS EN 14782:2006 BS 5950-7:1992 BS EN 506:2000 BS EN 502:2000 CP 143-10:1973 BS 61001.5.2:1987 96/104019 DC 02/105004 DC 03/115371 DC Title Roofing products from metal sheet. Specifications for fully supported roofing products of zinc sheet Roofing products from metal sheet. Specification for self-supporting products of steel, aluminium or stainless steel sheet. Steel Roofing products from metal sheet. Specification for self-supporting products of steel, aluminium or stainless steel sheet. Aluminium Roofing products from metal sheet. Specification for self-supporting products of steel, aluminium or stainless steel sheet. Stainless steel Roofing products from metal sheet. Specification for fully supported roofing products of aluminium sheet Roofing products from metal sheet. Specification for fully supported roofing products of steel sheet Roofing products from metal sheet. Specification for fully supported roofing products of copper sheet Self-supporting metal sheet for roofing, external cladding and internall ining. Product specification and requirements Structural use of steelwork in building. Specification for materials and workmanship: cold formed sections Roofing products from metal sheet. Specification for self-supporting products of copper or zinc sheet Roofing products from metal sheet. Specification for fully supported products of stainless steel sheet Code of practice for sheet roof and wall coverings. Code of practice for sheet roof and wall coverings. Galvanized corrugated steel. Metric units Glossary of building and civil engineering terms. General and miscellaneous. Operations. Associated plant and equipment. Jointing prEN 503. Roofing products from metal sheet. Specification for fully supported roofing products of lead sheet prEN 14509. Self-supporting double skin metal faced insulating sandwich panels. Factory made products. Specification EN 14783. Fully supported metal sheet and strip for roof coverings and wall finishes Status Current Current Current Current Current Current Current Current Current, Obsolescent Current Current Current, Proposed for Confirmation Current, Proposed for Confirmation, Work in Hand Current, Draft for Public Comment Current, Draft for Public Comment Current, Draft for Public Comment

British Standards for Clay/Stone Roofing Products:Standard Number BS EN 538:1994 Title Clay roofing tiles for discontinuous laying. Flexural strength test Status Current

BS EN 1024:1997 BS EN 1304:2005 BS EN 5391:2005 BS EN 14437:2004 DD CEN/TS 15087:2005 BS EN 5392:1998 04/30099864 DC BS EN 123261:2004 BS EN 123262:2000

Clay roofing tiles for discontinuous laying. Determination of geometric characteristics Clay roofing tiles and fittings. Product definitions and specifications Clay roofing tiles for discontinuous laying. Determination of physical characteristics. Impermeability test Determination of the uplift resistance of clay or concrete tiles for roofing. Roof system test method Determination of the uplift resistance of installed clay and concrete interlocking tiles for roofing. Test method for mechanical fasteners Clay roofing tiles for discontinuous laying. Determination of physical characteristics. Test for frost resistance BS EN 539-2. Clay roofing tiles for discontinuous laying. Determination of physical characteristics. Part 2. Test for frost resistance Slate and stone products for discontinuous roofing and cladding. Product specification Slate and stone products for discontinuous roofing and cladding. Methods of test

Current Current Current Current Current Current, Work in Hand Current, Draft for Public Comment Current Current

British Standards for Prefabricated/Modular Buildings and Structural Steel BuildingsBritish Standards Institute June 2006 Analysis of the British Institute website has identified the following British Standards for Structural Steel Buildings.Standard Number BS 449-2:1969 BS 5950-3.1:1990 BS 5950-4:1994 BS 5950-9:1994 DD ENV 1090-1:1998 BS 5950-7:1992 KIT 14 BS 5950-2:2001 BS 5950-6:1995 BS EN 1993-1-1:2005 BS 5502-21:1990 DD ENV 1993-13:2001 BS 5950-8:2003 Title Specification for the use of structural steel in building. Metric units Structural use of steelwork in building. Design in composite construction. Code of practice for design of simple and continuous composite beams Structural use of steelwork in building. Code of practice for design of composite slabs with profiled steel sheeting Structural use of steelwork in building. Code of practice for stressed skin design Execution of steel structures. General rules and rules for buildings (together with United Kingdom national application document) Structural use of steelwork in building. Specification for materials and workmanship: cold formed sections Structural use of steelwork in building set Structural use of steelwork in building. Specification for materials, fabrication and erection. Rolled and welded sections Structural use of steelwork in building. Code of practice for design of light gauge profiled steel sheeting Eurocode 3. Design of steel structures. General rules and rules for buildings Buildings and structures for agriculture. Code of practice for selection and use of construction materials Eurocode 3. Design of steel structures. General rules. Supplementary rules for cold formed thin gauge members and sheeting Structural use of steelwork in building. Code of practice for fire resistant design Status Current Current Current Current Current Current, Obsolescent Current Current Current Current Current Current Current

BS EN 1993-1-2:2005 BS EN 1993-110:2005 BS EN 1993-1-8:2005 BS EN 1993-1-9:2005 BS EN 1994-1-2:2005 BS 5950-1:2000 DD ENV 133812:2002 BS 5975:1996 BS EN 1994-1-1:2004 BS 6180:1999 BS 8414-2:2005

Eurocode 3. Design of steel structures. General rules. Structural fire design Eurocode 3. Design of steel structures. Material toughness and throughthickness properties Eurocode 3. Design of steel structures. Design of joints Eurocode 3. Design of steel structures. Fatigue Eurocode 4. Design of composite steel and concrete structures. General rules. Structural fire design Structural use of steelwork in building. Code of practice for design. Rolled and welded sections Test methods for determining the contribution to the fire resistance of structural members. Vertical protective membranes Code of practice for falsework Eurocode 4. Design of composite steel and concrete structures. General rules and rules for buildings Barriers in and about buildings. Code of practice Fire performance of external cladding systems. Test method for nonloadbearing external cladding systems fixed to and supported by a structural steel frame Structural use of steelwork in building. Code of practice for design of cold formed thin gauge sections Test methods for determining the contribution to the fire resistance of structural members. Applied protection to steel members Test methods for determining the contribution to the fire resistance of structural members. Applied protection to concrete/profiled sheet composite members Test methods for determining the contribution to the fire resistance of structural members. Applied protection to concrete filled hollow steel columns Code of practice for sheet roof and wall coverings. Code of practice for sheet roof and wall coverings. Galvanized corrugated steel. Metric units ISO 24314. Structural steels. Steels for seismic improved resistance for building EN 10340. Steel castings for structural uses

Current Current Current Current Current Current, Work in Hand Current Current Current Current Current

BS 5950-5:1998 DD ENV 133814:2002 DD ENV 133815:2002 DD ENV 133816:2002 CP 143-10:1973 05/30092093 DC 04/30123271 DC

Current, Work in Hand Current Current

Current

Current, Proposed for Confirmation Current, Draft for Public Comment Current, Draft for Public Comment