book 4: under floor slab - welcome to tegraseal · pdf fileinstallation guidelines under slab...
TRANSCRIPT
INSTALLATION GUIDELINES
Under Slab Applications
TegraSeal Products, LLC manufactures multiple waterproofing systems designed for various building
specifications.
The TegraTite Plus system consists of a 20 mil HDPE membrane laminated to 1 lb per SF of high swell bentonite
clay with a protective scrim overlay. This waterproofing system can be installed with the bentonite clay facing up
or down depending on contractor preference or specification.
Under floor application of TegraTite Plus with the bentonite clay facing up has its seams typically stapled and
sealed with TegraSeal’s proprietary CureTite Mastic Adhesive applied in and over seams.
TegraTite Plus installed with the bentonite clay facing down is typically stapled and taped with TegraSeal’s Seam
Tape or Bitumen Tape.
The TegraSeal 500 waterproofing system is adhered in place when installed. There are no nails or staples used in
this system, which makes it an ideal solution for vapor and gas prevention.
The TegraSeal 500 can be installed with the bentonite clay facing up or down and also utilizes the CureTite
Mastic Adhesive or TegraSeal Bitumen Tape for seaming.
The TegraSeal 500 consists of a 4 mil cross laminated HDPE membrane, modified bentonite clay and scrim. It
weighs 0.6 lbs per SF and is applied to surfaces with CureTite Adhesive.
A TegraSeal 1000 is also available and weighs 1 lb per SF.
The TegraSeal TripleSeal waterproofing system consists of bentonite clay laminated to both sides of a 20 mil
HDPE plastic. There is no up or down because it forms a waterproofing seal in every direction. TripleSeal is
ideal for the toughest waterproofing projects. The TripleSeal system also uses the CureTite Mastic Adhesive to
adhere in and over its seams.
All TegraSeal waterproofing systems are available with polymer modified bentonite for contaminate resistance or
elevated Sodium conditions. Simply specify CSR after selecting your system.
GENERAL INSTRUCTIONS
a. Protect waterproofing from rain and elements—keep covered until installed.
b. Ensure storage area is free from standing water and is properly drained.
c. TegraTite Plus and TripleSeal may be installed over uncured, damp or frozen surfaces.
d. TegraSeal 500 or 1000 may be installed over any surface reasonably clean and able to absorb or
evaporate the CureTite Adhesive.
e. Use a safety knife to cut and trim the all waterproofing membranes.
f. Contact TegraSeal Products, LLC whenever excessive conditions of acid, alkali, or salt brine exist.
g. TegraTite Plus, TripleSeal and TegraSeal 500 waterproofing systems require confinement on both
sides equivalent to or above 24 lbs per SF.
PREPARATION:
1. Prepare substrate/base/sub grade
a. Level and compact the original earth, or granular aggregate base.
2. Vapor barrier. (Detail 0704-10)
a. Cover compacted base with 6 mil polyethylene for TergaTite Plus and TripleSeal, 20
mil HDPE for the TegraSeal 500 or 1000.
b. Cut around any penetrations.
c. Over lap seams 3-4”.
d. Staple the seam every 6”-12” for TergaTite Plus and TripleSeal Systems. No stapling for
the TegraSeal 500 or 1000 waterproofing systems.
3. Install as specified by the Architect or Engineer. (Detail 0704-10) Figure 1
4. Utility Penetrations. (Detail 0704-50)
a. Apply TegraSeal Mastic around the penetration.
b. Cut a waterproofing membrane strip: 6” wide to wrap the pipe with 2”overlap. Every
2”, cut 4” flanges across the strip (Figure 1).
c. Wrap the strip around the pipe with flanges spreading out.
d. Hold the collar with pipe clamp or TegraSeal Seam Tape and/or fasteners.
e. Trowel TegraSeal Mastic to fill voids and cover with a collar.
WATERPROOFING SYSTEM INSTALLATION:
5. Tie-in under slab to wall or footing (Detail 0704-20)
a. Footings- wrap waterproofing sheet inside the form.
b. Place waterproofing sheet up and above the footing form to provide for a proper tie-in to under floor
or wall waterproofing. Typical tie in is 4” – 6”.
6. Tie-in under slab to lagging walls with footings and pile caps, (Details 0704-22).
a. Hang the 20 mil HDPE down the lagging wall and inside the form of the footing.
b. Concrete piling (if applicable)- Cut hole in waterproofing membrane and wrap tightly around the
piling. Pour TegraSeal Granular Pack cant around the piling or use TegraSeal Mastic and cover with
a waterproofing membrane collar.
c. Wrap the form with waterproofing membrane, extending up the lagging wall above
the cold joint and up the footing above the form. Tie in overlap seams 4” – 6”.
Cover entire floor area with selected waterproofing system – (TegraTite Plus, TripleSeal, TegraSeal 500 or 1000).
7. Sub grade - compacted earth, aggregate or mud slab (0704-10)
a. Install vapor barrio over stable, smoothed and compacted sub grade up to the footing. Overlap seams
6” and tape or staple down.
b. Pour TegraSeal Granular Pack cant along vertical to horizontal transition (0704-22 Detail 1).
c. Install waterproofing system sheet along the footing extending up the vertical surface.
d. Allow a 3" overlap, stagger sheets; securely fasten seams with staples, fasteners or tape.
e. Apply CureTite Mastic Adhesive in and over seams when specified.
8. Mud slab
a. Pour TegraSeal Granular Pack bentonite cant along vertical to horizontal transition.
b. Install waterproofing membrane along the footings extending up the vertical surface.
c. Install waterproofing membrane with minimum 3" overlap, stagger end laps; securely fasten seams
with staples every 20” O.C. and staple 6" O.C.
9. Expansion Joints contact TegraSeal Products, LLC for expansion joint drawings.
10. Complete installation at utility penetrations and floor drain (Detail 0704-50, Detail 0704-51).
a. Cut out a circle the diameter of the pipe in the center of a 2’ x 2’ square of waterproofing membrane.
b. Cover the pipe penetration with the waterproofing material square (if necessary, cut slit in center
circle).
c. Fill voids with TegraSeal Mastic or Granular Packs
11. Terminate vertical surfaces with a continuous strip of TegraSeal Termination Bar nailed every 12” O.C.
(Details 0704-22).
CONCRETE:
12. Concrete should not be dropped from higher than 3 feet (1.22 m).
TEGRASEAL
6 MIL POLYETHYLENE
TRANSITION WITH BELOW FLOOR DRAINAGE FLOOR TO WALL
TEGRATITE PLUS,TRIPLESEAL OR TEGRASEAL 500 OR 1000WITH CURETITE ADHESIVE
TEGRATITE PLUS
GRANULAR PACK
TRIPLESEAL
TEGRASEAL 500 OR 1000
TEGRATITE PLUS
CURETITE ADHESIVE
TEGRASEAL 500 OR 1000
MUD SLAB
TRIPLESEAL
EARTH FILL AGGREGATE,
EARTH FILL AGGREGATE,
TEGRATITE PLUS(BENTONITE DOWN)
TEGRATITE PLUS
EARTH FILL AGGREGATE,
TEGRASEAL TERMINATION BAR
OR TRIPLESEAL SYSTEM20 MIL HDPE - TEGRASEAL 500 OR 1000
(2" CANT)
WATERSTOPTEGRASTOP
SYSTEM
TEGRATITE PLUS(BENTONITE UP)
TEGRASEAL TERMINATION BAR, SEAM TAPE OR BITUMEN TAPE
TEGRASEALGRANULAR PACK(2" CANT)
TEGRASEALGRANULAR PACK(2" CANT)
TEGRASEAL TERMINATION BAR, SEAM TAPE OR BITUMEN TAPE
TEGRASEAL TERMINATION BAR
TEGRASEALGRANULAR PACK(2" CANT)
ELEVATOR PIT CROSS SECTION DETAIL
6 MIL POLYETHYLENE
TEGRATITE PLUS,TEGRASEAL 500 OR 1000WITH CURETITE ADHESIVE OR TRIPLESEAL
TEGRATITE PLUS,
TRIPLESEAL
TEGRASEAL 500 OR 1000
TEGRATITE PLUS
TEGRATITE PLUS
TEGRATITE PLUS DRAIN BOARD (OPTIONAL)
TEGRASEAL 500 OR 1000
DRAIN BOARD (OPTIONAL)
MUD SLAB
TRIPLESEAL
TRIPLESEAL
DRAIN BOARD (OPTIONAL)
WATERPROOFING
OR TRIPLESEAL 20 MIL POLYETHYLENE TEGRASEAL 500 OR 1000
(BENTONITE UP)
TEGRATITE PLUS
TEGRATITE PLUS
TEGRATITE PLUS DRAIN BOARD (BENTONITE (OPTIONAL)DOWN)
SYSTEM
TEGRASTOPWATERSTOP
ALL SEAMS ADHERABLE WITH TEGRASEAL MASTIC ADHESIVE
OVERLAP
WATERPROOFING CROSS SECTION UNDER FLOOR
WITHOUT MUD SLAB
WITH MUD SLAB
TYPICAL OVERLAP
WITH OUT MUD SLAB / PROTECTION SHEET
WITH MUD SLAB
TYPICAL OVERLAP
TYPICAL UNDER FLOOR
TYPICAL OVERLAP
WITHOUT MUD SLAB
TRIPLESEAL
TRIPLESEAL
TRIPLESEAL
TEGRASEAL 500 OR 1000WITH CURETITE ADHESIVE
MUD SLAB
MUD SLAB
TEGRATITE PLUS(BENTONITE DOWN)
TEGRATITE PLUS
TEGRATITE PLUS(BENTONITE UP)
3"
TEGRASEALSEAM TAPE OR BITUMEN TAPE
TEGRASEAL 500 OR 1000WITH CURETITE ADHESIVE
TEGRASEAL 500 OR 1000WITH CURETITE ADHESIVE
OVERLAP OVERLAP3"
BITUMEN TAPE
(BENTONITE DOWN)
(BENTONITE DOWN)
(BENTONITE DOWN)
(BENTONITE DOWN)
6 MIL POLYETHYLENE
20 MIL HDPE PROTECTION
3"
6 MILPOLYETHYLENE
TRIPLESEAL TEGRASEAL 500 OR 1000TEGRATITE PLUS
6 MIL POLYETHYLENE
6 MIL POLYETHYLENE
COVER (TYPICAL)
20 MIL HDPE PROTECTION COVER (TYPICAL)
20 MIL HDPE PROTECTIVE COVER (TYPICAL)
AGGREGATE
(TYPICAL)
TEGRASEAL
AND BASE SHEET
6 MIL POLYETHYLENE - TEGRATITE PLUS,
FOOTING TO FLOOR TRANSITION CROSS SECTION
TEGRATITE PLUS,TEGRASEAL 500 OR 1000OR TRIPLESEAL WATERPROOFING SYSTEM
OR TERMINATION BAR
TEGRASEAL GRANULAR
TEGRATITE PLUS(BENTONITE DOWN)
TEGRASEAL 500 OR 1000WITH CURETITE ADHESIVE
6 MIL POLYETHYLENE
TEGRATITE PLUS
TEGRASEAL 500 OR 1000
TRIPLESEAL
MUD SLAB
TRIPLESEAL
TRIPLESEAL
6 MIL POLYETHYLENE
6 MIL POLYETHYLENE
(BENTONITE DOWN)
OR TRIPLESEAL20 MIL HDPE - TEGRASEAL 500 OR 1000
TEGRATITE PLUS(BENTONITE UP)
TEGRATITE PLUS(BENTONITE DOWN)
TEGRATITE PLUS
6 MIL POLYETHYLENE
TEGRASEAL SEAM TAPE, BITUMEN TAPE
TEGRASEAL TERMINATION BAR,SEAM TAPE OR BITUMEN TAPE
TEGRASEAL TERMINATION BAR,SEAM TAPE OR BITUMEN TAPE
BITUMEN TAPETEGRASEAL
TERMINATION TEGRASEAL
BAR
PACK (2" CANT)
TEGRASEAL EXPANDABLE TAPE
TEGRATITE PLUS WATERPROOFING
TEGRATITE PLUS
WATERPROOFING AROUND EXTERIOR PILECAPS
20 MIL HDPE OR DRAIN BOARD
DOUBLE LAYER TEGRATITE PLUS WATERPROOFING OVER COLD
WATERPROOFING
TEGRATITE PLUSWATERPROOFING (BENTONITE DOWN)
6 MIL POLYETHENE
(BENTONITE UPOPTIONAL)
COLLAR
TERMINATION BAROR WOOD LATH
TEGRATITE PLUS WATERPROOFING (BENTONITE AGAINST EARTH FILL)
6 MIL POLYETHYLENE
GRANULAR PACK(2" CANT)
(BENTONITE FACING CONCRETE)
TEGRATITE PLUS
JOINTS (BENTONITE FACING CONCRETE)
GRANULAR PACK(2" CANT)
TEGRASEAL MASTIC
DETAIL 1
OPTION 1
DETAIL 2
OPTION 2
TEGRASEALMASTIC
GRANULAR PACK(2" CANT)
TEGRASEAL EXPANDABLE TAPE WITH CURETITE
TEGRASTOP WATERSTOP
TEGRATITE PLUS WATERPROOFING
TEGRATITE PLUS WATERPROOFING (BENTONITE AGAINST CONCRETE)
TEGRASEAL
TEGRASEAL
TEGRASEAL
TEGRASEAL
ADHESIVE
TEGRASTOP WATERSTOP
NOTE: TEGRASEAL 500 OR 1000 AND TRIPLESEAL ALTERNATIVE DRAWINGS ALSO AVAILABLE
WATERPROOFING PILECAP BELOW FOOTING
STEP 2: INSTALL TEGRATITE PLUS(BENTONITE AGAINST FILL)
6 MIL POLYETHYLENE OR DRAIN BOARD
STEP 3: FOLD BACK MEMBRANE AND STAPLE 8" O.C.
STEP 1: FOLD MEMBRANE OVER TO ALLOW PROPER TIE-IN TO FLOOR
TEMPORARILY FASTEN MEMBRANE
AND WALL TRANSITION
TEGRATITE PLUS
TEGRASEAL 500 OR 1000
TRIPLESEAL
STEP 2: INSTALL TEGRASEAL 500 OR 1000WITH CURETITE ADHESIVE
STEP 3: FOLD BACK MEMBRANE AND USE CURETITE ADHESIVE
(BENTONITE AGAINST FILL)
STEP 2: INSTALL TRIPLESEAL
STEP 3: FOLD BACK MEMBRANE AND STAPLE 8" O.C.
20 MIL HDPE OR DRAIN BOARD
6 MIL POLYETHYLENE OR DRAINAGE BOARD
BENTONITE DOWN/ MEMBRANE UP
WATERPROOFING INTERIOR FOOTING
STEP 2: INSTALL TEGRATITE PLUS(BENTONITE AGAINST CONCRETE FLOOR)
6 MIL POLYETHYLENE OR DRAIN BOARD
STEP 3: FOLD BACK MEMBRANE AND STAPLE 8" O.C.
STEP 1: FOLD MEMBRANE OVER TO ALLOW PROPER TIE-IN TO FLOOR
TEMPORARILY FASTEN MEMBRANE
AND WALL TRANSITION
TEGRATITE PLUS
TEGRASEAL 500 OR 1000
TRIPLESEAL
STEP 2: INSTALL TEGRASEAL 500 OR 1000WITH CURETITE MASTIC ADHESIVE IN AND OVER
20 MIL HDPE OR DRAIN BOARD
STEP 3: FOLD BACK MEMBRANE SEAM WITH CURETITE MASTIC ADHESIVE
SEAMS (BENTONITE AGAINST CONCRETE FLOOR)
STEP 2: INSTALL TRIPLESEAL MEMBRANE
6 MIL POLYETHYLENE OR DRAIN BOARD
STEP 3: FOLD BACK MEMBRANE AND STAPLE 8" O.C.
BENTONITE UP / MEMBRANE DOWN
TYPICAL DRAIN DETAIL
TEGRATITE PLUS, TRIPLESEALOR TEGRASEAL 500 OR 1000WITH CURETITE ADHESIVE WATERPROOFING SYSTEM
TEGRATITE PLUS
TEGRASEAL 500 OR 1000
TRIPLESEAL
TEGRATITE PLUS
TEGRASEAL 500 OR 1000WITH CURETITE
MUD SLAB
TRIPLESEAL
MUD SLAB
MUD SLAB
ADHESIVE (BENTONITE DOWN)
(BENTONITE UP)TEGRATITE PLUS
MUD SLAB
(BENTONITE DOWN)
TEGRATITE PLUS
CLAMP OR
TEGRATITE PLUS, TRIPLESEALOR
PIPE PENETRATION (TYPICAL) UNDER SLAB
STEP ONE
STEP TWO
MASTIC
STEP THREE
CLAMP OR TEGRASEAL SEAM
TEGRASEAL
SEAM TAPE
TEGRATITE PLUS,
TEGRASEAL 500 OR 1000 WATERPROOFING SYSTEM
6 MIL POLYETHYLENE - TEGRATITE PLUS,TRIPLESEAL20 MIL HDPE - TEGRASEAL 500 OR 1000
TEGRASEAL 500 OR 1000COLLAR
TEGRATITE PLUS,TRIPLESEAL ORTEGRASEAL 500 OR 1000COVER
TRIPLESEAL OR
TAPE
6 MIL POLYETHYLENE - TEGRATITE PLUS,TRIPLESEAL20 MIL HDPE - TEGRASEAL 500 OR 1000
TegraSeal Products, LLC
9231 Penn Ave S, Suite 2A
Bloomington, MN 55431
Toll-free: 888-815-1816
Tel: 952-888-1816
Fax: 952-888-1786
www.tegraseal.com
This manual is provided as a general guideline for the typical installation of TegraSeal
Waterproofing Membranes and is not intended to cover all potential installation details. The
information provided in this manual is correct to the best of our knowledge and belief at the
date of its publication. Please contact TegraSeal for additional information.
Printed in USA-Ver 050710