User manual V2.0

Thank you for purchasing BlackView.BlackView is a

portable, Stylish, high-performance vehicle drive

recorder. It has 5.0M effective pixel high-definition CMOS

image sensor, intelligent voice reminder, enhanced

night shooting,140°wide-angle lens.

Specific performance parameters are as follows:

CMOS sensor 5,000,000 pixels

Viewing angle of lens Wide-angle 140°

Turning angle of lens 200° back and forth

Screen 2.0TFT high resolution

Quality vedio HD(1280×720)@30fps

Night vision Enhanced night vision

Format of picture JPEG

Pixel of picture 2560x1920

Voice guidance intelligent voice guidance

Type of memory card TF card

Capacity of memory Card Supports up to 32G

Battery 800MA Polymer lithium battery

Power consumption 150MA

Check the product and the accompanied accessories

!

distributor.If there is any problem of the accessories, contact your local product

Checking the packing content

BlackView Support Slot

Power cable Driver disk

User m aualn Cable holders

Checking the main body of the BlackView

Lens

Enhanced night vision lightSpeaker

Vedio Play Camera

Microphone

Switching&Menu

TF Card Slot

USB Interface

TFT LCD

ResetSupport slot

1.Stop the engine and remove the key from the ignition.

Installing the BlackView

Install the BlackView in a well-lit and safe location.

2.Insert the Micro SD card into the BlackView.

3.Attach the BlackView into the windshield of your car using double-sided tape.Use a soft and dry cloth to wipe the foreign material and moisture attached in the surface of the support slot.

4.Connect the [USB] terminal of the BlackView and the cigarette jack of your car using the power cable.

5.Tie the power cableUse the provided cable holder, when necessary.

6.Adjust the position of the camera lens of the BlackView.

Ensure that it is level with the ground.

7.Start the engine. Check whether the BlackView is installed When the BlackVue is installed correctly, its Intelligent voice systems will play“The BlackView has been starting normal recording”.

Using the Normal Recording Function

Using the BlackView

Start the engine.BlackView turns on and starts the Normal Recording function. After it is turned on, it will records and saves scenes at each specified period.Stop the engine.BlackView will turn off after about 5 seconds.

Using the Manual Reconrding FunctionPress the <Switching> button on the BlackView.After BlackView turns on.Press the <Camera> button to starts the Manual Recording function. It will record and saves scenes at each specified period.Press the <Camera> button again.BlackView will exit

.Manual

Recording function

Using the Camera Function

Using the Playback Function

When BlackView turns on. To enter the Camera Function Press the <Camera> button.Press the <Camera> button again.BlackView will take photograph.

When BlackView turns on. Press and hold <Play> button for 2 seconds to enter the Playback Function.Press <Camera> or <Vedio>button to select the video or photo which you want,Then Press <Play> button to play.Press and hold <Play> button for 2 seconds again. The BlackView will exit the Playback Function.

Setting video output

Setting the BlackView

Video output including【Size】【EV】【White Balance】【Video Time】【Night Mode】

1.Setting 【Size】When System is turned on.Press <Switching> button to display video

output page.

Press <Camera> or <Vedio> button to select【Size】,Then Press

<Play> button to display Sub-page.

Sub-page including【VGA】【QVGA】【D1】【HD】,Press

<Camera> or <Vedio>button to select the setting which you want,Then

Press <Play> button to confirm.

2.Setting 【EV】

When System is turned on.Press < Switching > button to display video

output page.

Press <Camera> or <Vedio> button to select【EV】,Then Press <Play>

button to display Sub-page.

Sub-page including【+2.0】【+5/3】【+4/3】【+1.0】【+2/3】【+1/3】

【+0.0】【-1/3】【-2/3】【-1.0】【-4/3】【-5/3】【-2.0】,Press

<Camera> or <Vedio> button to select the setting which you want,Then

Press <Play> button to confirm.

O K Set

Size

White Balance

Vedio Time

Night Mode

HD

Auto

1 Min

O ff

Exit

Video output Setup

Q VGA

D1

EV +0.0

VGA

Setting the BlackView

3.Setting 【White Blance】When System is turned on.Press < Switching > button to display video output

page.

Press <Camera> or <Vedio> button to select【White Blance】,Then

Press <Play> button to display Sub-page.

Sub-page including【Auto】【Daylight】【Cloudy】【Tungsten】【

Fluorescent】,Press <Camera> or <Vedio> button to select the setting

which you want,Then Press <Play> button to confirm.

O K Set

White Balance

Size

Vedio Time

Night Mode

Auto

HD

1 Min

O ff

Exit

Video output Setup

Auto EV +0.0 Daylight

Tungsten

Cloudy

Fluorescent

O K Set

EV

White Balance

Vedio Time

Night Mode

+0.0

Auto

1 Min

O ff

Exit

Video output Setup

+0.0

Size HD +1/3

-2/3

-1.0

-1/3

Setting the BlackView

4.Setting 【Vedio Time】

5.Setting 【Night Mode】

When System is turned on.Press < Switching > button to display video

output page.

Press <Camera> or <Vedio> button to select【Night Mode】,Then

Press <Play> button to display Sub-page.

Sub-page including【Off】【On】,Press <Camera> or <Vedio> button

to select the setting which you want,Then Press <Play> button to

confirm.

O K Set

Video Time

White Balance

Size

Night Mode

1 Min

Auto

HD

O ff

Exit

Video output Setup

O ff

2 Min

EV +0.0 1 Min

When System is turned on.Press < Switching > button to display video

output page.

Press <Camera> or <Vedio> button to select【Night Mode】,Then

Press <Play> button to display Sub-page.

Sub-page including【Off】【On】,Press <Camera> or <Vedio> button

to select the setting which you want,Then Press <Play> button to

confirm.

Setting the BlackView

O K Set

Night Mode

White Balance

Vedio Time

O ff

Auto

1 Min

Exit

Video output Setup

O ff EV +0.0

Size HD

On

Setting SetupSetup including【Format】【beep】【language】【auto off】【sys.reset】【Light Freq.】【USB】【Screen Set】

1.Setting 【Format】Double click<Switching> button to display

Setup page.

Press <Camera> or <Vedio> button to select Format ,Then Press

<Play> button to display subpage.

Subpage including【Cancel】【Execute】,Press <Camera> or <Vedio>

button to select the setting which you want,Then Press <Play> button to

confirm.

When System is turned on.

【 】

O K Set

Format

Language

Auto Off

Beep

Next Menu

English

O ff

On

Exit

Video output

Cancel

Execute

Setup

Sys.Reset

Next Menu

Setting the BlackView

2.Setting 【Beep】

When System is turned on.Double click<Switching> button to display

Setup page.

Press <Camera> or <Vedio> button to select【Beep】,Then Press

<Play> button to display subpage.

Subpage including【On】【Off】,Press <Camera> or <Vedio> button to

select the setting which you want,Then Press <Play> button to confirm.

3.Setting 【Language】When System is turned on.Double click<Switching> button to display

Setup page.

Press <Camera> or <Vedio> button to select【Language】,Then

Press <Play> button to display subpage.

Subpage including【English】【繁體中文】【简体中文】【日本語】【

Русский】,Press <Camera> or <Vedio> button to select setting

which you want,Then Press <Play> button to confirm.

O K Set

Beep

Language

Auto Off

Format

On

English

O ff

Next Menu

Exit

Video output

On

O ff

Setup

Sys.Reset

Next Menu

Setting the BlackView

O K Set

Language

Format

Auto Off

Beep

English

Next Menu

O ff

On

Exit

Video output

English

Setup

Sys.Reset

Next Menu

简体中文

日本語

Русский文

4.Setting 【Auto Off】

When System is turned on.Double click<Switching> button to display

Setup page.

Press <Camera> or <Vedio> button to select【Auto Off】,Then Press

<Play> button to display subpage.

Subpage including【1 Min】【3 Min】【5 Min】【Off】,Press

<Camera> or <Vedio> button to select the setting which you want,Then

Press <Play> button to confirm.

O K Set

Auto Off

Format

Language

Beep

O ff

Next Menu

English

On

Exit

Video output

1 Min

Setup

Sys.Reset

Next Menu

3 Min

5 Min

Off

Setting the BlackView

5.Setting 【Sys.Reset】

When System is turned on.Double click<Switching> button to display

Setup page.

Press <Camera> or <Vedio> button to select【Sys.Reset】,Then

Press <Play> button to display subpage.

Subpage including【Cancel】【Execute】,Press <Camera> or

<Vedio> button to select the setting which you want,Then Press <Play>

button to confirm.

6.Setting 【Light Fre.】

When System is turned on.Double click<Switching> button to display

Setup page.

Press <Camera> or <Vedio> button to select【Light Fre.】,Then Press

<Play> button to display subpage.

Subpage including【60Hz】【50Hz】,Press <Camera> or <Vedio>

button to select the setting which you want,Then Press <Play> button to

confirm.

O K Set

Sys.Reset

Beep

Auto off

Language

Next Menu

Language

Light Freq.

Date Input

Exit

Video output

Cancel Execute

Format

Next Menu

Setup

Setting the BlackView

O K Set

Light Freq.

USB

Screen Set

60Hz

PC Cam

Aways On

Exit

Video output

60Hz 50Hz

Setup

7.Setting 【USB】

When System is turned on.Double click<Switching> button to display

Setup page.

Press <Camera> or <Vedio> button to select【Light Fre.】,Then Press

<Play> button to display subpage.

Subpage including【60Hz】【50Hz】,Press <Camera> or <Vedio>

button to select the setting which you want,Then Press <Play> button to

confirm.

O K Set

USB

Light Freq.

Screen Set

PC Cam

60Hz

Aways On

Exit

Video output

PC Cam Disk Drive

Setup

Setting the BlackView

8.Setting 【Screen Set】

When System is turned on.Double click<Switching> button to display

Setup page.

Press <Camera> or <Vedio> button to select【Screen Set】,Then

Press <Play> button to display subpage.

Subpage including【Always On】【1 Min】【3 Min】,Press

<Camera> or <Vedio> button to select the setting which you want,Then

Press <Play> button to confirm.

O K Set

Screen Set

Light Freq.

USB

Aways On

60Hz

PC Cam

Exit

Video output

Away On 1 Min

Setup

Ballasoft