bennett 3000 series mechanical

107929 Rev E 04-24-17

Includes Instructions For: Model 3100 Commercial Mechanical 101 (Volume Only) Non-computer with Electric Reset Model 3200 Commercial Mechanical, 101 (Volume Only) Non-Computer & Cam AC Reset Model 3300 Retail Mechanical (Money & Volume), V/R 10/4 & Electric Reset Model 3400 Retail Mechanical (Money & Volume), V/R 10/4 & Cam AC Model 3500 Retail Mechanical (Money & Volume), V/R 10 & Electric Reset Model 3600 Retail Mechanical (Money & Volume), V/R 10 & Cam AC Remote Dispensers and Self-Contained Pumps

READ THIS MANUAL This manual has important information for safe installation and operation of this equipment. Read and understand this manual before applying power. Keep this manual and tell all service personnel to read this manual. If you do not follow the instructions, you can cause bodily injury, death or damage to the equipment.

For new manuals, FAX to: BENNETT MARKETING SERVICES (231)799-6202 or visit our web page at: http://www.bennettpump.com

Bennett 3000 Series Mechanical Commercial and Retail Dispensers

Installation & Operator’s Manual Only Trained Personnel May Work on This Equipment

Bennett 1218 E. Pontaluna Road, Spring Lake, MI 49456 USA 800-235-7618 ~ Outside USA 231-798-1310

[email protected] ~ www.bennettpump.com

2 107929 Rev E 04-24-17

NOTICE Not all equipment covered in this manual is listed by Underwriters Laboratories. Only those products that bear the Listing Mark of Underwriters Laboratories are listed.

IMPORTANT Examine the shipment immediately upon arrival to make certain there has been no damage or loss in transit. Bennett Pump Company, as shipper, is not liable for the hazards of transportation. Please make damage claims directly to the truck line.

Safety Instructions 3

Introduction for the 3000 series Mechanical Commercial and Retail Dispensers 4

Product Specifications 6

Determining the Model Number 7

Dispenser Identification Number Summary (DIN) 8

Unloading, Unpacking and Inspecting a New Dispenser 9

Lifting a New Dispenser and Placing it on the Island 10

Adjustable Nozzle Hook Instructions 12

Determining the Number of Product Supply Pipes Needed 14

Mechanical and Plumbing Notes 15

Electrical Field Wiring 15

Pipelines and Under Ground Containment Sumps 17

Above Ground Tank Installations 18

Purging Product Lines for Remote Dispensers 19

Purging Product Lines for Self Contained Dispensers 19

Piping Notes for Self Contained (Suction) Pumps 20

Dispenser Startup and Checklist 21

How to Mechanically Calibrate the SB-100 Meter 23

Operator Instructions 24

Owner Maintenance 26

Maintenance by Bennett Authorized Service Representative 27

Potting Instructions 28

Base Dimensions and Wiring Diagrams 28

Site Audit Form 43

Bennett Limited Warranty for Products Installed in the United States - 3000 Retail & Commercial 46

Bennett International Limited Warranty for Dispensers and Pumps ........................................................ 47

Table of Contents

3 107929 Rev E 04-24-17

DANGER: Fire, explosion, injury or death will occur if fuel filters are changed by untrained personnel. Make sure only trained personnel change filters.

CAUTION: Do not drill holes in fuel dispensers. Holes can cause failure of the electronic equipment. The warranty will become void. Use only adhesive backed sign mounting brackets.

WARNING: When anchoring the dispenser, always level the dispenser with shims before bolting to the island. DO NOT shim just the middle of the dispenser and bolt down.

WARNING: Make sure this equipment is correctly grounded. Failure to do will cause injury or damage equipment or improper operation. Improper grounding voids the warranty.

WARNING: You must have training in the operation and programming of this dispenser before using it. READ THE OPERATORS MANUAL.

WARNING: The emergency shut-off valve (also called the fire valve, shear valve or impact valve) must be closed when service or maintenance is performed on this equipment.

WARNING: Electronic components are static sensitive. Use proper static precautions (static straps) before working on the equipment.

WARNING: To prevent electric shock, keep the electrical parts of the dispenser dry.

WARNING: You must have training in the installation, service or maintenance of this equipment (dispenser, pump, console, control box or submerged pump) before working on it. Maintenance repairs must be done by authorized personnel only. Warranty work may only be performed by Bennett certified technicians.

DANGER: Disconnect all power to this equipment and associated submerged pump(s) during installation, service or any maintenance, i.e., changing filters.

DANGER: Gasoline is flammable. NO SMOKING OR OPEN FLAME.

DANGER: To prevent injury to you from vehicles and onlookers, always place a barrier around this equipment before performing service or maintenance.

WARNING ADVERTISSEMENT ADVERTENCIA For the safe installation of this equipment, read and understand all warning and cautions. Look for these warnings:

“DANGER” means: If you do not follow the instructions, severe injury or death will occur. “WARNING” means: If you do not follow the instructions, severe injury or death can occur. “CAUTION” means: If you do not follow the instructions, damage can occur to the

READ AND UNDERSTAND ALL WARNING LABELS ATTACHED TO THE DISPENSER

Safety Instructions

4 107929 Rev E 04-24-17

Mechanical Computer or Non-computer

Fleetmaster 3000 uses Veeder-Root 4-wheel non-computer with totalizer.

Heritage 3000 uses Veeder-Root 4-wheel VR 10/4 computer with totalizer (optional VR10 extended price range computer)

U.S. Gallons, Liters or Imperial Gallons for vol-ume measurement

Various currency measurements for Heritage 3000 series depending upon country applica-tion

Veeder-Root electric reset, 115 or 230 volt (optional Cam-AC manual reset)

Field wiring terminal strip in junction box located in the top display area (installers should pull 72” (272 cm) of wire above grade level). Explosion proof j-box in lower hydraulic area is optional. Hydraulics

Precision Bennett SB100 Meter, 4 piston posi-tive displacement design

Type 75 Bennett rotary vane pumping unit with integral vortex air eliminator

All remote units include built in inlet check valves to keep the hydraulics full and prevent meter/pulser count up when the submersible pump pressurizes the system

Remote units use replaceable paper filter

Suction pumps use re-useable strainer

All units feature 1” hose outlets with 1 x 3/4” reducer bushing

1-1/2” ground joint union inlet

Options

Veeder-Root pulsers, 10:1 or 100:1 (VR10 us-es OPW-FMS “Western” supplied by others for field installation).

2-Stage prepay/preset electric solenoid valve for 1 product, 1-hose or 2-product, 2-hose suc-tion pumps. (Valve is standard on all other models)

Internal spin on filter & adaptor for remote mod-els

For High Hose models, Balance vapor coax hose outlet and internal vapor return piping

Healy active vapor for High Hose systems

Sub pump relay 3 phase contactor

Valence style top for High Hose models

Brushed stainless steel lower doors

Custom lower door colors and/or graphics

Hose clamp for 5/8”, 3/4”, or 1” I.D. hose

Explosion proof junction box for lower hydraulic area

380 Volt 3-Phase Motors

Cam-AC manual reset in lieu of electric reset

VR10 Veeder-Root extended price range com-puter for Heritage 3000 series

Internal Hose retractor

Strainer in lieu of filter for remotes

Strainer w/ cloth sack for remotes

Strainer w/ cloth sack for suction units

Hoses, nozzles, swivels

Introduction

5 107929 Rev E 04-24-17

Standard Features

Mechanical analog display

Stand-alone or console-controlled when

pulser options are specified

Can be controlled by fleet management

system when pulser options are specified

Unit of measure for US gallons, liters, or

imperial gallons

Operates from 115/230Vac, 60/50Hz, or

380 Vac, 50Hz

Self-contained (suction) models feature 1

-HP continuous duty motors

Cascade fluorescent dial face lighting

Satellite Outlet Connection

Self-contained (suction) models: single,

1-product twin, or 2-product twin

Remote models: single, 1-product twin,

or 2-product twin Construction

Low Hose Cabinet Design or

High Hose Cabinet Design

Long-life cabinet construction using

galvaneal components and powder coated panels

Black end panels and top

Black dial face covers

Red lower doors (optional colors

available)

Hinged swing out lower door

Hinged swing down upper door

Heavy duty hose hook (optional internal

spring rewind retractor available) Mechanical Computer or Non-Computer

Fleetmaster uses Veeder-RootTM 4-wheel

non-computer with totalizer

Heritage uses Veeder-Root 4-wheel

VR10/4 computer with totalizer (optional VR10 extended price range computer)

U.S. Gallons, Liters, or Imperial Gallons

for volume measurement

Various currency measurements for

Heritage series depending upon country application

Veeder-Root Electric Reset, 115 or

230volt (optional Cam-Ac manual reset)

Field wiring terminal strip in junction box

located in top display area (installers should pull 72” (272 cm) of wire above grade level). Explosion proof j-box in lower hydraulic area is optional.

Hydraulics

Precision Bennett SB100 Meter, 4-piston,

positive displacement design

Type 75 or type 75-HD Bennett sliding

vane pumping unit with integral vortex air eliminator

Hydraulics Cont’d

All remote units include built-in inlet

check valves to keep the hydraulics full and prevent meter/pulser count-up when the submersible pump pressurizes the system

Remote units use replaceable paper filter

Suction pumps use a reusable strainer

All units feature 1” hose outlets with a

1”x3/4” reducer bushing

1-1/2” ground-joint union inlet

Options

Veeder-Root Pulsers, 10:1 or 100:1

(VR10 uses OPW-FMS “Western” Pulser supplied by others for field installation).

2-Stage prepay/preset electric solenoid

valve for 1-product, 1-hose or 2-product, 2-hose suction pumps. (valve is standard on all other models)

Internal spin-on filter & adapter for

remote models

For High Hose Models, Balance vapor

coax hose outlet and internal vapor return piping

Vapor recovery nozzle boot kit (field

installed) for balanced vapor nozzles

Healy active vapor system for high hose

Subpump relay 3-Phase Contactor

Intercom speaker for High Hose units

Valance style top for high hose models

Brushed stainless steel lower doors

Brushed stainless steel end panels

Custom lower door colors and/or

graphics

Hose clamp for 5/8”, 3/4”, or 1” I.D. hose

Explosion proof junction box for lower

hydraulic area

380 Volt 3-Phase Motors

Pressure-regulating valve for suction

pumps with aboveground tank installation

E85 alcohol blend compatibility option

Cam-Ac manual reset in lieu of electric

reset

VR10 Veeder-Root extended price range

computer for Heritage 4000 series

Hand Crank for select models with Cam-

Ac manual reset

Internal Hose Retractor

Strainer in lieu of filter for remotes

Strainer w/ cloth sack for remotes

Strainer w/ cloth sack for suction units

Hoses, nozzles, swivels

Companion LPS satellites

For information on flow rates, motor sizes, and model configurations see our Model Configuration Chart & Specification Sheet

ULTM listed Certified for resale applications. The N.T.E.P. Certificate of Conformance is available upon request

Specifications in this document are subject to change without notice.

Mechanical Dispensers and Pump Specification Sheet Fleetmaster 3000 Volume Only and Heritage 3000 Money/Volume Displays

6 107929 Rev E 04-24-17

POWER REQUIREMENTS

Motor Power—Standard Motors (self-contained) are 115/230v, 60/50 Hz. An optional 380v, 50 Hz 3-phase motor is available. Electric Reset - 115volt 50/60Hz OR 230volt 50/60Hz depending on customer specification at time of order. Fluorescent Lamps - Ballast is one of four types: 115v 60 Hz OR 115v 50Hz OR 230v 60Hz OR 230v 50Hz depending on customer specification at time of order. Two Stage Electric Solenoid Valves - 115v 50/60 Hz OR 230v 50/60 Hz depending on customer specification at time of order.

ENVIRONMENTAL REQUIREMENTS

Operating Temperature Range: -30° to +50°C Humidity: 0-95% non - condensing

DIMENSIONS 3000 Series - Low Hose 60” H X 30” W x 20” D High Hose 88”H x 30”W x 20”D

Product Specifications

7 107929 Rev E 04-24-17

Determine the model number of the dispenser from the serial plate located in the dispenser. Utilizing the chart below determine the features of the dispenser to be installed. Understanding the features of the dispenser to be installed will be helpful in understanding the proper installation of the dispenser.

How a Model for the 3000 Series Dispensers is Made Up.

Note - Motor -The hydraulic arrangement can be as follows: Remote (submerged pump), Suction with Standard 1 phase 115/230 v.a.c. 50/60 Hz, Suction with 1 phase 115/230 v.a.c. 50/60 Hz with prepay valves, Suction with 3 phase 380 v.a.c. 50 HZ, Suction with 3 phase 380 v.a.c. with pre-pay valves

Determining the Model Number

Pump Model Retail Commercial Activation Method # Products # Hoses Motor

3111 X Electric Reset 1 1 See Note

3211 X Cam AC Reset 1 1

3311 X Electric Reset 1 1
















8 107929 Rev E 04-24-17

Determining the Model Number

9 107929 Rev E 04-24-17

Bennett dispensers are bolted to a pallet and then carefully packaged with cardboard/styrofoam liners and a cardboard exterior carton. The entire package is then securely wrapped with plastic shrink wrap. Use a fork lift to lift the dispenser from the bottom while it is still on the pallet. Bennett dispensers are shipped from our factory F.O.B. This means that the title to the equipment passes to the purchaser at the time the equipment is loaded on the truck at our factory. Freight damage claims are the responsibility of the purchaser. Bennett will assist you in preparing any damage claim, by helping you identify and price any parts necessary to make needed repairs. Before signing the freight delivery receipt, inspect the carton and pallet for any obvious signs of damage that may have damaged the dispenser. If any damage is found, instruct the delivery driver to make a notation on the delivery receipt before you sign. If possible, open the carton and inspect the dispenser before signing the delivery receipt. Carefully remove the plastic shrink-wrap from the carton. Then carefully remove the cardboard container and any inside liners. DO NOT DISCARD THE PACKAGING. Should the need arise to repackage the dispenser, the cardboard packaging can be reused. Plastic shrink-wrap can be purchased at office supply stores or industrial packaging stores. Examine the exterior panels for any signs of freight damage. Should you encounter any damage after signing for delivery, call the freight carrier immediately and request an inspection. DO NOT DISCARD THE PACKAGING; the inspector will want to examine it. Once you are sure that there is no freight damage to the exterior of the dispenser, use the door key (one key is wire tied to the nozzle hook) to unlock the lower door. Remove the lower door from both sides of the dispenser. Visually examine the interior of the dispenser for shipping damage. While the dispenser is extremely sturdy, a dispenser that has been “dropped” can suffer damage internally even while it appears normal on the exterior. Check for and tighten any bolts or nuts that appear loose. Read the model/serial plate of the dispenser and check to confirm that the hydraulic configuration is what your order specified. Report any non-shipping related problems to Bennett Customer Service: In USA, telephone (800) 235-7618 or outside the USA, telephone (231) 798-1310; or via FAX to (231) 799-6202; or via email to [email protected]. Or write to us at: Bennett Pump Company or Bennett Commercial Pump Company 1218 E. Pontaluna Road Spring Lake, Michigan, USA 49456

Unloading, Unpacking, and Inspecting a New Dispenser

10 107929 Rev E 04-24-17

The dispenser is bolted to a pallet with bolts and nuts. With the lower doors removed and safely stored away, remove the nuts and bolts that secure the dispenser to the pallet.

Thread two lifting straps (900 lbs. Capacity each minimum) through the dispenser as shown in Figures 1 and 2. Be careful not to allow the straps to go under any of the hydraulic castings such as the meter outlet, copper tubes or valves. The straps should be lifting only against the front and rear chassis. Use a forklift or pallet lifting device with the forks spread wider than the pump and gently lift the dispenser. This lifting method will also work on the high hose dispenser. Place the dispenser gently on the island using care to line up the base anchor bolt holes with the anchor bolts embedded in the concrete island. WARNING: Lift only to the height required to set the dispenser on the island. Keep hands and feet clear of the dispenser while it is suspended in the air.

Fig. 2 - Front View - Using lifting straps to lift and move the dispenser.

Fig. 1 - Side View - Using lifting straps to lift and move the dispenser. Notice the forks are spread wider than the pump.

Unlock the lower door with the keys that come with the unit. Swing the door open 90 degrees and lift.

Remove the door and store in a safe place until you are ready to put the door back

Lifting a New Dispenser and Placing it on the Island

11 107929 Rev E 04-24-17

Lifting a New Dispenser and Placing it on the Island Alternate Method for High Hose

Lifting the Dispenser from Above - On the high hose models, there are lifting brackets provided in the upper area of the dispenser. There is a cover that has to be removed to access these brackets. (See Figures 1 + 2 below).

Fig. 1 - Cover is screwed onto the top of the dis-penser and must be removed to access the lifting brackets.

Fig. 2 - After the top cover is removed, the lifting brackets can be accessed for lifting the dispenser from above.

The dispenser must be bolted firmly to the concrete island. The dispenser base is provided with anchor bolt holes (see base drawings in back of this manual for dimensions). Anchor bolts embedded in the concrete island must be not less than ½” diameter. The threaded ends of the anchor bolts should project 1½” above the concrete. On the Low Hose dispenser, 2 anchor bolts required minimum. On the High Hose dispenser, 4 anchor bolts required minimum in the outer 4 mounting holes. Refer to the Base Drawings in the back of this manual for hole locations. When anchoring the dispenser, always level the dispenser with shims before bolting to the island.. Place the shims at the location of the anchor bolts so the dispenser frame is not distorted when the anchor bolts are tightened down.

Anchoring the Dispenser to the Island

12 107929 Rev E 04-24-17

For standard interchangeable nozzles, use bottom mounting holes in nozzle hook bracket as shown above. Examples of standard nozzles are OPW 11A, Husky X.

Use top mounting holes in nozzle hook bracket as shown above for the following nozzles: OPW 7H & 7BH; Richards Mark 7 & 7B; Husky VIII, VIIIS, & 1-HS; Emco A6000 series; Catlow MAX-1

Addendum to 103848, 104652, and 105993 Technical Publications Part number 106467 Instruction Sheet for Adjustable Nozzle Hook (Rev A 9/02)

Adjustable Nozzle Hook Instructions

13 107929 Rev E 04-24-17

This page intentionally left blank

14 107929 Rev E 04-24-17

Step 1: Determine the type of supply line needed from the model number’s 7th position on the serial tag. If the model number is 3111SNR (Note the R) the dispenser will require a submerged pump and pressurized supply line for each product. If the model number is 3111SNS (Note the S) the pump will require a suction supply line for each product. Step 2: Determine the number of product pipes required by finding the model number below. Model Number Product Supply lines required 3111 Use 1 Product Line plumbed to position 1 3211 Use 1 Product Line plumbed to position 1 3311 Use 1 Product Line plumbed to position 1 3411 Use 1 Product Line plumbed to position 1 3511 Use 1 Product Line plumbed to position 1 3611 Use 1 Product Line plumbed to position 1 3112 Use 1 Product Line plumbed to position 1 3212 Use 1 Product Line plumbed to position 1 3312 Use 1 Product Line plumbed to position 1 3412 Use 1 Product Line plumbed to position 1 3512 Use 1 Product Line plumbed to position 1 3612 Use 1 Product Line plumbed to position 1 3122 Use 2 Product Lines plumbed to positions 1 & 2 3222 Use 2 Product Lines plumbed to positions 1 & 2 3322 Use 2 Product Lines plumbed to positions 1 & 2 3422 Use 2 Product Lines plumbed to positions 1 & 2 3622 Use 2 Product Lines plumbed to positions 1 & 2 *Refer to base drawings in the back of this manual for product inlet locations. Pipe Size - 1-1/2 “ inlet nipples come on all units.

1-1/2” nipple.

Determining the Number of Product Supply Pipes Needed

15 107929 Rev E 04-24-17

Mechanical and Plumbing Notes

For remote dispensers, a U.L. Listed Emergency Shut Off Valve is required for each product inlet. The Emergency Shut Off Valve is sometimes referred to as an “Impact Valve”, “Safety Valve”, “Shear Valve”, “Crash Valve”, or “Fire Valve”. The Emergency Shut Off Valve must be supported by the island frame or containment sump frame. Follow all instructions contained in the valve’s installation manual and observe all local codes.

For self-contained (suction) pumps, a vertical check valve is required under each of the pump’s ground joint unions for the product inlet. The vertical check valve ensures that the pump’s hydraulic system remains full of product, and it is necessary to maintain the

“prime” of the suction line so that liquid product does not drain back to the tank. Follow all instructions contained in the vertical check valve’s installation manual and observe all local codes. For above ground tank installations with suction pump units, a pressure regulating valve is required on the product line. Product inlet locations and dimensions are in the base foundation drawings in this manual. Tighten the dispenser’s ground joint union to leak free tightness. If rigid product inlet pipes are used, they must be plumed to the proper position so that no strain is exerted on the dispenser chassis when the ground joint union is tightened.

Install an approved emergency Shut Off valve, designed to close automatically in the event of severe impact or fire exposure, in the dispenser supply line at the base of the dispenser. The valve will also permit safe inspection and maintenance. Follow the installation instructions for the valve being installed.

Find the wiring diagram specific to the dispenser model for the dispenser that you are working on in the “Wiring Diagrams” section in the back of this manual. Read and follow all directions including supplemental notes contained on the drawing. The dispenser’s wiring terminal strip for connection of the field wiring is in the ballast box (upper “Head” ) of the dispenser. Remove the screws securing the top cover of the dispenser to access the wiring terminal. Also, the dispenser has the option of being ordered with a junction box in the lower part of the dispenser. If you have this option, you will wire to the terminal strip in the junction box the same way you would have wired to the terminal strip in the head of the dispenser. All field wiring must be Oil and gas resistant (THHN) color coded, with a 600 volt insulation rating. See wiring manual for proper wire sizes. Pull 72” extra wire to reach the top of the dispenser. Do not use wire nuts. The ends of the wires should be clean and free from oxidation. No more than two dispensers per 15 amp breaker. All dispensers must be on the same phase of power. Follow all local, state and federal requirements for installation of vapor seals. Electrical contractors must pull 72” of wire above the grade level to reach through the dispenser’s conduit and into the ballast box area at the top of the dispenser. Read and follow all instructions on the wiring diagram and observe all national and local electrical codes. In instances where new dispensers are replacing old dispensers, Bennett recommends that new wiring be pulled to each dispenser. If existing wiring is to be used (not recommended) does not reach to the dispenser ballast area (top area) of the dispenser, wire extension is allowed only if the connections are soldered and made weather proof.

Electrical Field Wiring

16 107929 Rev E 04-24-17

Electrical Field Wiring (Cont’d)

The wire separator (supplied with the pump) must be installed on the wires as they exit the conduit located in the electrical enclosure before the wires are terminated in the electronics enclosure. The wire separator is needed to properly seal the conduit in the last step of installation. Underground conduit for the field wiring must be 3/4”, rigid metal and continuous. The use of PVC conduit is not allowed. All conduit between the building and each dispenser should be a separate conduit run. The dispenser may come with or without the optional junction box located in the lower area of the dispenser. If there is a junction box, follow the instructions for wiring to the j-box under the “Wiring Diagrams” section of this manual. Up to two dispensers may be placed on one 15 amp circuit breaker. No more than two dispensers per 15 amp breaker. All dispensers at the station must be on the same phase of power. All dispenser field wiring between the building and the dispenser for power, neutral and ground wire conductors must not be spliced, wire nutted or shared with any other equipment. Doing so would void the Bennett Limited Warranty. All power, neutral and ground conductors shall be run from the dispenser to the Main Service Panel. Follow all local, state and federal requirements for installation of vapor seals. In instances where new dispensers are replacing old dispensers, Bennett recommends that new wiring be pulled to each dispenser. If existing wiring is used (not recommended) and does not reach to the dispenser electronic head (top area) of the dispenser, the wires can be extended only if the connections are soldered and weather proof and contained in an explosion-proof type junction box. The maximum distance from the breaker panel to the dispenser is 500 feet. For self-contained units, increase the motor wire size from 14Ga to 12Ga for runs over 50ft. and to 10Ga. for runs over 100ft, 8 Ga. For runs over 250 feet. Note: if 230v motor power is used be sure to set the motor switch located on the motor to the high voltage setting by moving the switch to the high position. WARNING: DO NOT CROSS PHASE THE DISPENSERS OR DAMAGE WILL OCCUR. When installing more than one dispenser the remote sub-pump relay control wire from each dispenser must be on the same phase of power or cross phasing will occur at the sub-pump relay. This means that the pump power for all dispensers at the site must be on the same phase. Electrical Conduits - Make sure that each dispenser has it’s own electrical underground conduit. Wiring from multiple dispensers in a single conduit is not allowed. All underground conduit should be rigid metal and drawn up tight. The use of PVC (plastic) conduit is not allowed and will void the Bennett Warranty. Make sure that vapor “seal offs” are properly installed on all conduits at and from each dispenser.

17 107929 Rev E 04-24-17

Pipelines and Underground Containment Sumps

General - The dispenser must be mounted on a concrete foundation. Do not pour concrete around the product pipes or electrical conduit. The use of a UL approved containment sump designed for the Bennett Dispenser Model used is highly recommended. Follow the containment sump manufacture’s installation instructions for proper installation. If no containment sump is used, fill the sump area with clean sand or dirt as far up the product pipe as possible once installation is complete. Use water to pack the sand in place. See Figures.

NOTE: All piping must be clean of foreign debris, such as: oil, grease and shavings. All connections must be tight to prevent leaks.

Swing joints or flex pipe must be used at the ends of the horizontal pipe between the dispenser and the tank. See Figure. These joints prevent leaks which might develop through ground movement from settling of the tank, frost heaving of the ground or pump island settling. The joint under the dispenser also aids proper alignment of the product union or coupling.

NOTE: Make sure the installation conforms to EPA regulations for underground storage tanks.

Underground Piping

Figure 1 - Example of Remote Contained Figure 2 - Example of Self-Contained

18 107929 Rev E 04-24-17

Bennett self contained dispensers can be used with above ground tank installations if the following requirements are met:

An Underwriters (U.L.) Listed Pressure Regulating Valve designed for under-the-pump mounting is installed for each pumping unit according to the valve manufacturer’s instructions.

Any additional valves suggested by the Pressure Regulating Valve manufacturer are installed according to the manufacturer’s recommendations.

The installation must be installed and used in accordance with Federal, State, Local, and National Electrical code NFPA #70 and Automotive and Marine service station code NFPA 30A.

Above Ground Tank Installation with Self Contained Pumps

19 107929 Rev E 04-24-17

Purging Product Lines for Self Contained Systems

Once product piping and tanks have been tested for leaks and any leak conditions have been fixed, and all electrical connections have been made and verified, the remote dispenser product lines must be purged of all air that may be trapped in the lines. CAUTION! DO NOT USE THE DISPENSER TO PURGE AIR FROM THE PRODUCT LINES. RUNNING THE METER IN A DRY CONDITION AND AT THE HIGH SPEEDS RESULTING FROM PRESSURIZED AIR, WILL DAMAGE THE METER AND VOID THE BENNETT LIMITED WARRANTY. The emergency shut off valve contains a test port that may be used to bleed off air that may be trapped in the product lines for remote units. Manually close the emergency shut off valve. Do not leave this process unattended while purging the air from the product lines. Once liquid fuel product begins to weep from the test port, retighten the plug in the test port. It is recommended that at least 150 gallons of fuel be pumped from each hose to eliminate any air in the line. If more than one dispenser is on a submerged pump product feed line, start this purging process at the dispenser furthest from the submerged pump and work backwards toward the submerged pump. WARNING! Take appropriate measures to contain any product seepage from the test port. Dispose of any spilled product in proper manner consistent with applicable laws and codes. Manually open the emergency shut off valve and lock it into the “on” position according to the instructions from the valve manufacturer. Use an approved test can or other appropriate approved container to dispense 50 gallons or 175 liters through the dispenser. Begin dispensing by only slightly opening the nozzle to allow any entrapped air in the dispenser to slowly release through the nozzle. This prevents over-speeding of the meter. Once the dispenser has dispensed 150 gallons of fuel, the SB100 meter should be tested for calibration. Refer to the section in this manual for calibration procedures.

Once product piping and tanks have been tested for leaks and any leak conditions have been fixed, and all electrical connections have been made and verified, the self contained (suction) dispenser product lines must be purged of all air that may be trapped in the lines. The pumping unit evacuates all the air in the pipe before it gets to the meter. The air is expelled through the vent at the top of the pump. Nothing but fuel should pass through the meter. The meter will not turn until fuel enters the pump and pressurizes the system. WARNING! Take appropriate measures to contain any product seepage from the air elimination chamber tube. Dispose of any spilled product in proper manner consistent with applicable laws and codes. Use an approved test can or other appropriate approved container to dispense 50 gallons or 175 liters through the dispenser. Begin dispensing by only slightly opening the nozzle to allow any entrapped air in the dispenser to slowly release through the nozzle. This prevents over-speeding of the meter. Once the dispenser has dispensed 150 gallons of fuel, the SB100 meter should be tested for calibration. Refer to the section in this manual for calibration procedures.

Purging Product Lines for Remote Dispensers

20 107929 Rev E 04-24-17

To obtain maximum flow rates on a self-contained pump, follow these guidelines: The total length of horizontal piping between the pump and tank must be no longer than 60 feet. Use new 1-1/2” galvanized or approved non-metallic pipe for 10-15gpm pumps. Use new 2” galvanized or approved non-metallic pipe for 20-24 gpm pumps. All horizontal piping must be buried a MINIMUM of 18” below the finished grade The pipe from the tank must slope up to the pump (approximately 1-1/2” to 2” per 10 feet). The piping run should not have any high or low spots (hills or valleys). The pipe must be supported continuously to prevent sagging. All piping must hold a 50 PSI pressure test for 10 minutes. To absorb ground movement from settling of the tank, frost heaving of the ground or pump island settling, a swing joint must be used in the supply line at the tank and directly underneath the dispenser. Three additional directional changes using elbows are permitted. Only one pumping unit is permitted for each underground pipe. Two pumps on one suction line is not recommended. Static lift on self-contained units must not exceed 10 feet (vertical distance between product level in the storage tank and the center of the pumping unit). All Installation work must conform to federal, state, and local codes. Above Ground Tanks - If using above ground tanks, make sure a vacuum actuated pressure regulating valve is properly installed. Follow Petroleum Equipment Institute’s Recommended Practices for Installation of Underground Liquid Storage Systems RP100 and/or Recommended Practices for Installation of Above Ground Storage Systems for Motor Vehicle Fueling RP200.

Copies of PEI’s recommended practices can be order through their web site at: www.pei.org

Piping Notes for Self Contained (Suction) Pumps

21 107929 Rev E 04-24-17

DANGER: Fire, explosion, injury or death will occur if fuel vapors are present. Make sure there are no vapors present before starting this procedure. CAUTION: To prevent damage to the dispenser, follow the proper start-up procedures.

Before applying AC power to the dispenser, follow this procedure: 1. Unlock and open the upper and lower dispenser doors. 2. Check to make sure:

The components have not come loose from shipping. The cables are properly connected. There are no torn cables or stranded harnesses. Pulser and pump handle harnesses are connected properly.

3. Make sure the shut off valves are closed. 4. Turn off all submerged pump circuit breakers and all other circuit breakers to the dispenser.

Make sure the 12-gauge green ground wire is properly connected between the dispenser and the ground bus at the Main Service Panel.

Check the Dispenser Power Circuit

1. Turn on 115 or 230 Volts AC dispenser power to the unit. 2. Use a voltmeter to verify 115 or 230 Volts AC only at Terminal 10 on the dispenser terminal strip.

Terminal 2 of the terminal strip is neutral. This AC circuit provides power to the electric reset. Check the Submerged Pump Motor Circuit: Remotes

WARNING: To prevent injury, make sure impact valves and submerged pump breakers are off.

1. Put the 1st Product’s pump handle in the ON position. The dispenser will reset (all 000’s on the mechanical display). Use a voltmeter to verify 115 or 230 Volts AC across the two black wires coming out of the Electric Reset. This is the voltage that is used to energize the control relay coil. Refer to the Wiring Diagram for Remote Dispensers in the back of this manual.

2. Put the 1st Product pump handle in the OFF position. 3. Open and set the Shut Off (impact) valves.

Dispenser Startup and Checklist

22 107929 Rev E 04-24-17

Self-Contained WARNING: If the lower door on the pulley side of the unit is off, close the door and lock it to

prevent injury. 1. Verify that the motor voltage select switch on the self contained motor is in the proper position. 2. Turn on this products self contained pump motor circuit breaker. With the pump handle OFF, use a

voltmeter to verify 115/230 Volts AC power for the self contained pump motor by measuring between the two black wires coming out of the electric reset. These wires should be connected to the field wires for the pump motor power. If the motor is being operated off of 230 volts, this reading will measure 230 Volts A.C. This products pump motor should not be running at this time.

3. Turn off this product’s pump motor circuit breaker. 4. Repeat this test for any remaining dispensers. All Dispensers 1. Turn off all circuit breakers. 2. Close and lock the lower doors and the upper doors. 3. Turn the circuit breaker for the system on. 4. Purge the air from the system.

5. Dispense a small amount of fuel from each hose to verify all positions are counting. Proceed to the section for finishing the installation called “Potting Instructions”. Then proceed to the section titled “How to Calibrate the SB-100 Meter” .

Dispenser Startup and Checklist (Cont’d)

23 107929 Rev E 04-24-17

Example 1

1. A fast flow test at 11 GPM shows a +3 cu. in. reading in a five gallon test measure.

2. Remove the existing seal and pin and turn the

dial clockwise (-)five minimum adjustments (half holes) and reinsert the pin.

3 cu. in. = 5 half holes (-)CW .6 cu. in./adjustment 3. Test and reseal.

Example 2

1. A fast flow test at 11 GPM shows a -2 cu. in. reading in a five gallon test measure.

2. Remove the existing seal and pin and turn the

dial counterclockwise (+) three minimum adjustments (half holes) and reinsert the pin.

2 cu. in. = 3 half holes (+) CCW .6 cu. in./adjustment 3. Test and reseal

Each SB-100 meter is provided with the following calibration information: The dial adjusting cover has (+) and (-) arrows

to indicate the correct direction to rotate the dial to either increase or decrease delivery.

A self-adhesive metal label listing the minimum incremental adjustment is attached to the collector housing immediately above the adjusting dial.

The dial cover has two pin hubs, one to the left of the shaft and one to the right. The seal pin may be inserted in either hub. See Figure 21. The smallest adjustment (.6 cu. in.) occurs when the pin is pulled from one side and inserted in the other side by moving the dial the least amount or half a hole. A 1.2 cu. in. adjustment is made by pulling the pin and turning the dial until the next adjacent hole aligns with the same hub and reinserting the pin.

To calibrate the meter, follow this procedure:

1. Measure the actual delivery of the meter at fast flow in an accurate test measure. Dispense a minimum of 5 gallons (20 liters).

2. Cut and remove the existing seal wires and remove the seal pin. See Figure 22.

3. Turn the dial the necessary amount in the (+) or (-) direction to increase or decrease the quantity of fuel delivered.

4. Re-insert the seal pin in the desired pin hub.

5. Dispense 5 gallons (20 liters) of fuel to allow the meter to adjust to the new settings. Do not make any adjustments based on this delivery.

6. Make sure the meter is properly calibrated. Dispense another 5 gallons (20 liters) of fuel into an official test measure to check the calibration.

The Bennett SB-100 Meter is built to maintain accurate measurement under normal operating conditions. The meter is a positive displacement device with rods and pistons, which require a break in period. The meter is calibrated at the factory using a solvent for safety purposes, and must be calibrated after it has been installed. We strongly suggest recalibration of the meter after a 90 day break in period.

How to Calibrate the SB-100 Meter

24 107929 Rev E 04-24-17

DANGER: Gasoline is flammable. NO SMOKING OR OPEN FLAME WITHIN 100’ OF THE EQUIPMENT.

DANGER: Fire, explosion, injury or death will occur if untrained personnel change fuel filters. Make sure only trained personnel change filters. The Bennett mechanical computing fuel dispenser is simple to operate: ELECTRIC RESET ACTIVATION

1. Remove nozzle from the dispenser’s nozzle boot.

2. Insert nozzle fully into the vehicle fill pipe.

3. Rotate On-Off Lever fully to the “On” position .

The electric reset will turn on (you can usually hear the reset motor running)

The computer or non-computer dials will reset to zero.

The self-contained pump’s motor will turn on or if it is a remote dispenser you will hear the electric solenoid valve click open.

4. Squeeze the nozzle lever and dispense the desired amount of fuel. Some nozzles will be

automatic shut-off style and may be equipped with a latch open device, which can be set at several flow rate points. If the nozzle is not equipped with a latch open device, you must hold the nozzle lever open. DANGER: Do not attempt to block open the nozzle lever with any foreign objects.

DANGER: The operator must remain in view of the nozzle at all times while the dispenser is on or while the nozzle is removed from the dispenser’s nozzle boot.

5. When the desired amount of fuel has been dispensed into the vehicle, close the nozzle.

6. Turn the dispenser’s on/off handle to the “Off” position.

7. Return the nozzle to the nozzle boot of the dispenser. 8. Replace the vehicle’s fuel cap. DANGER: No not dispense fuel into unapproved containers.

Operator Instructions

25 107929 Rev E 04-24-17

1. Remove nozzle from the dispenser’s nozzle boot.

2. Insert nozzle fully into the vehicle fill pipe.

3. Rotate the Reset Handle (small handle)

The computer or non-computer dials will reset to zero.

4. Rotate On-Off Lever fully to the “On” position .

The self-contained pump’s motor will turn on or if it is a remote dispenser you will hear the electric solenoid valve click open.

5. Squeeze the nozzle lever and dispense the desired amount of fuel. Some nozzles will be

automatic shut-off style and may be equipped with a latch open device, which can be set at several flow rate points. If the nozzle is not equipped with a latch open device, you must hold the nozzle lever open. DANGER: Do not attempt to block open the nozzle lever with any foreign objects.

DANGER: The operator must remain in view of the nozzle at all times while the dispenser is on or while the nozzle is removed from the dispenser’s nozzle boot.

6. When the desired amount of fuel has been dispensed into the vehicle, close the nozzle.

7. Turn the dispenser’s on/off handle to the “Off” position.

8. Return the nozzle to the nozzle boot of the dispenser. 9. Replace the vehicle’s fuel cap. DANGER: No not dispense fuel into unapproved containers.

Cam Reset Activation

26 107929 Rev E 04-24-17

Some maintenance can be done without authorized service technicians if you read and follow all the safety precautions contained in this manual. Owners can do the following items: Visual Inspection for Leaks Bennett recommends that a visual inspection be done at least once a month or if a leak is suspected. WARNING: Turn off and lockout all circuit breakers associated with the dispenser to be inspected. WARNING: Blockade the work area around the dispenser to protect yourself from traffic. Unlock the door of the dispenser, carefully swing open and secure the door. Check for signs of dripping fuel or wet areas on all hydraulic connections and major components such as the meter, pumping unit, filter and filter casting, etc. If any sign of leaking fuel is detected, call an authorized Bennett Service Technician immediately. Lubricating Door Locks Use a graphite lock lubricant and follow directions on the lubricant container. Cleanup any excess so that it will not stain the painted surfaces of the dispenser. Internal or External Hose Retractors Inspect weekly to ensure that the nylon retractor cable is not wound around the product hose. Cleaning Exterior Clean all painted surfaces as needed with a mild detergent and water solution. Do NOT use a high pressure water sprayer to clean or rinse the dispenser. Clean stainless steel surfaces with a non-abrasive cleaner intended for cleaning stainless steel. Read and follow all directions on the cleaner container. To preserve the luster and lengthen the life of all metal surfaces, use a high grade automobile paste wax. Read and follow all directions on the wax container. Clean all surfaces prior to waxing. Do NOT use any harsh detergents, degreasers, or cleaners with abrasives.

Owner Maintenance

27 107929 Rev E 04-24-17

The following maintenance/service procedures should be performed ONLY by Bennett Authorized Service Representatives. Manually Opening or Closing the Emergency Shut-off Valve or Testing the Valve’s Operation

Emergency Shut-off Valves (Shear Valves, Impact Valves, Crash Valves) are required at the dispenser inlet for all remote dispensers. The valve incorporates a shear section so that the valve will close if a vehicle strikes a dispenser. The valve also incorporates a fusible link so that it will close in the event of a fire. Use only Bennett Authorized Service Representatives for this type of service. Changing Filters or Cleaning Strainers Use only Bennett Authorized Service Representatives for this type of service. Replacing or Repairing Hanging Hardware (Hoses, Nozzles, Swivels, Break-a-ways Use only Bennett Authorized Service Representatives for this type of service. Servicing any electrical or hydraulic components Use only Bennett Authorized Service Representatives for this type of service.

Maintenance by Bennett Authorized Service Representatives

28 107929 Rev E 04-24-17

Find the appropriate footprint dimensional drawings and wiring diagram for the model of dispenser being installed in the next section of this manual. Read and follow all directions and safety notices. WARNING: RISK OF ELECTRICAL SHOCK – More than one disconnect switch may be required to de-energize the device for serving.

Note - Dispenser electrical disconnect must comply with National Electrical Code, NFPA 70. WARNING: All doors must be replaced and locked when unit is in service. WARNING: EXPOSED BELTS AND PULLEYS. Do not operate pump with door removed except when required for maintenance and then only by a Bennett Authorized Service Representative. Keep clear of belts and pulleys.

1. Install field conduit dispenser per NFPA-70 along with any state and local codes.

2. Pull field wiring allowing 72” of extra wire to reach upper electrical enclosure.

3. Feed wire through conduit and into upper electrical enclosure. CAUTION: Don not damage wire while feeding through

conduit into the upper electrical enclosure. 4. Wrap some “CHICO X” fiber around wires and push into conduit

assembly to prevent potting from running down the length of the conduit. See figure.

5. Using the wire separator provided, install one wire in each hole until all wires are separated. See Figure.

6. Shorten field wiring to appropriate length when making connections.

7. Attach field wiring to terminal strip in upper electrical enclosure according to the wiring diagram supplied for this dispenser. See Figure.

8. Push wire separator at least 3/4” into conduit. 9. Prepare potting compound according to directions. NOTE: Use “CHICO A3” potting compound for sealing

fittings in hazardous locations. 10. Using a funnel, pour potting into conduit, be sure to get potting in

between each wire. See Figure. 11. Let stand until firm.

Potting Instructions

Footprint Dimensions and Wiring Diagrams

29 107929 Rev E 04-24-17


30 107929 Rev E 04-24-17


31 107929 Rev E 04-24-17


32 107929 Rev E 04-24-17


33 107929 Rev E 04-24-17


34 107929 Rev E 04-24-17


35 107929 Rev E 04-24-17


36 107929 Rev E 04-24-17


37 107929 Rev E 04-24-17


38 107929 Rev E 04-24-17


39 107929 Rev E 04-24-17


40 107929 Rev E 04-24-17


41 107929 Rev E 04-24-17


42 107929 Rev E 04-24-17


43 107929 Rev E 04-24-17

3000 Series Mechanical Site Audit Form

44 107929 Rev E 04-24-17

3000 Series Mechanical Site Audit Form (Cont’d)

45 107929 Rev E 04-24-17

Dispensers – 3000 Series Retail & Commercial Self Contained and Remote Warranty on parts, labor, and travel is 12 months from date of installation or 18 months from date of Bennett’s original invoice, whichever comes first. Warranty excludes nozzles, hoses and fittings, hose retractor, hose reels, filters, belt adjustments, paper jams, light bulbs, or any leaks after the installation start-up and audit. Minor adjustments such as meter calibration, pulser adjustments, and handle switch adjustments, customer specified items manufactured by others, and customer requested reprogramming of equipment are not covered by warranty. Field Retrofit Card Readers, Payment Modules, Cash Acceptors, and all other field retrofit Accessories The field retrofit assembly is warranted for parts only for 12 months from date of installation or 18 months from date of original invoice, whichever comes first, except the receipt printer and driver board which is warranted for parts for ninety (90) days from the date of installation or 180 days from original invoice, whichever comes first. Consumable Items such as receipt paper are not warranted. The use of receipt paper not specified by Bennett will void the printer assembly warranty. Model 515 Pump Controller, 621 Module, Fan Out Boxes Warranty on parts, labor and travel is 12 months from the date of installation or 18 months from the date of original invoice, whichever comes first. Software Bennett Pump Company warrants Bennett products and software packages, whose operation is controlled by Bennett designed and developed software, shall be free of material defects and conform to current Bennett specifications for a period of ninety (90) days from the date of original invoice. Bennett shall use its best effort to correct such defects and to supply to purchaser at Bennett’s expense, a corrected version within a reasonable time after purchaser notifies Bennett in writing of any defects and provides the programs and instructions required to reproduce the claimed defect. Warranty does not cover any modification to the program, the Bennett product, and/or connection to unapproved equipment made by any person or any defect caused by such modifications/connections. Upgrade Kits Bennett offers kits which are installed as an option to enhance operating features of an existing Bennett product are warranted for parts only for ninety (90) days from date of installation or 12 months from date of original invoice, whichever comes first. Upgrade Kit warranty applies to kit components only. Warranty status of the remainder of the product remains unchanged. Spare Parts For equipment under warranty: The warranty period for all spare parts replaced is the remainder of the original warranty. Spare Parts are warranted for the value of the parts only (no labor, mileage, or other charges). For equipment not under warranty: The warranty period is 90 days from the date of invoice to the end user, or 12 months from the date of original invoice, whichever comes first. Spare Parts are warranted for the value of the parts only (no labor, mileage, or other charges). General Exclusions

1. Warranty does not apply to any product which has been altered, subjected to unusual physical or electrical stress, an Act of God, damaged by accident, tampered with, or subjected to misuse or abuse including substituting parts or accessories from other manufacturers without the written consent of Bennett Pump Company. The above warranties shall not exist if the original identification marks have been removed or altered.

2. Bennett makes no warranty with respect to the Bennett equipment or Bennett’s performance of services under this agreement, express or implied, and Bennett hereby disclaims the implied warranties of merchantability and fitness for a particular purpose.

3. In no event shall Bennett be liable for any loss of profits, loss of use, interruption of business or indirect, special, incidental or consequential damages of any kind in connection with or arising out of the furnishing, performance, use or failure of the Bennett equipment, software or services acquired from Bennett, the distributor or the user, whether alleged as a breach of contract or tortuous conduct, including negligence. Bennett’s liability hereunder for damages shall not, in any event, exceed the amounts paid by the buyer to Bennett for equipment, software or services as to which the claim arose.

4. No action arising out of any claimed breach of the Warranty Agreement or transaction under this Warranty Agreement may be brought by either party more than two (2) years after the cause of action has accrued.

5. Use of non-Bennett replacement parts, unless specified by Bennett, will void the equipment warranty. 6. This warranty only applies to Bennett equipment installed in the United States of America and is non-transferable. 7. Failure to pay the Bennett invoice within stated invoice terms, covering the respective Bennett equipment purchased under this limited warranty

may, at Bennett’s discretion, void this limited product warranty. THE FOREGOING WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING, WITHOUT LIMITATION, THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

BENNETT PUMP COMPANY 1218 E. Pontaluna Road Spring Lake, MI 49456 Tel: 231-798-1310 Fax: 231-799-6202

Bennett Limited Warranty for Products Installed in the United States - 3000 Retail & Commercial

Bennett Pump Company guarantees new Service Station Equipment manufactured by Bennett against defects in material or workmanship during the warranty period in accordance with the provisions stated below:

The Site Audit Report issued with all equipment must be completed and returned at time of installation to Bennett Pump Company, Spring Lake,

MI to initiate warranty.

Warranty service must be performed by the nearest Bennett Authorized Service Representative qualified to perform service on the defective

equipment. Only Authorized and Certified Service Representatives are allowed to perform warranty service. Use of service personnel other than qualified Bennett Service Representatives without prior approval by Bennett Pump Company will void payment of any warranty claims.

Labor and travel costs incurred while servicing Bennett equipment will be paid at previously contracted rates subject to published standard repair

time allowances to qualified Bennett Service Representatives with travel cost limited to 200 miles. Travel cost shall be limited to 4 hours round trip.

Bennett equipment has been installed according to the manufacturer’s instructions and diagrams.

During the warranty period, Bennett Pump Company will, at its option, repair or replace defective parts returned to its factory, transportation

charges prepaid.

The manufacturer reserves the right to make changes in the design or to make additions

Form 1-1010-2 Rev B 10-20-14

46 107929 Rev E 04-24-17

Dispensers (Remote and Self-contained styles) (excluding Natural Gas, Hydrogen and Hydraulic-less Dispensers) The Warranty will cover repair or replacement, at Bennett’s option, of the parts only that are deemed to be defective in material or workmanship at Bennett’s discretion, for a period of 12 months from date of installation or 18 months from date of Bennett’s original invoice, whichever comes first. Warranty excludes nozzles, hoses and fittings, hose retractor, filters, belt adjustments, paper jams, light bulbs, or any leaks after the installation start-up and audit. Minor adjustments such as meter calibration, pulser adjustments, and handle switch adjustments, customer specified items manufactured by others, and customer requested repro-gramming of equipment are not covered by warranty. Field Retrofit Card Readers, Payment Modules, Cash Acceptors, and all other field retrofit Accessories The field retrofit assembly is warranted for parts only for 12 months from date of installation or 18 months from date of original invoice, whichever comes first, except the receipt printer and driver board which is warranted for parts for ninety (90) days from the date of installation or 180 days from original invoice, whichever comes first. Consumable Items such as receipt paper are not warranted. The use of receipt paper not specified by Bennett will void the printer assembly warranty. Model 515 Pump Controller, 621 Module, Fan Out Boxes Warranty on parts only is 12 months from the date of installation or 18 months from the date of original invoice, whichever comes first. Software Bennett Pump Company warrants Bennett products and software packages, whose operation is controlled by Bennett designed and developed software, shall be free of material defects and conform to current Bennett specifications for a period of ninety (90) days from the date of original invoice. Bennett shall use its best effort to correct such defects and to supply to purchaser at Bennett’s expense, a corrected version within a reasonable time after purchaser notifies Bennett in writing of any defects and provides the programs and instructions required to reproduce the claimed defect. Warranty does not cover any modification to the program, the Bennett product, and/or connection to unapproved equipment made by any person or any defect caused by such modifications/connections. Upgrade Kits Bennett offers kits which are installed as an option to enhance operating features of an existing Bennett product are warranted for parts only for ninety (90) days from date of installation or 12 months from date of original invoice, whichever comes first. Upgrade Kit warranty applies to kit components only. Warranty status of the remainder of the product remains unchanged. Spare Parts

For equipment under warranty: The warranty period for all spare parts replaced is the remainder of the original warranty. Spare Parts are warranted for the value of the parts only (no labor, mileage, or other charges). For equipment not under warranty: The warranty period is 90 days from the date of invoice to the end user, or 12 months from the date of original invoice, whichever comes first. Spare Parts are warranted for the value of the parts only (no labor, mileage, or other charges). General Exclusions

1. Warranty does not apply to any product which has been altered, subjected to unusual physical or electrical stress, an Act of God, damaged by accident, tampered with, or subjected to misuse or abuse including substituting parts or accessories from other manufacturers without the written consent of Bennett Pump Company. The above warranties shall not exist if the original identification marks have been removed or altered.

2. Bennett makes no warranty with respect to the Bennett equipment or Bennett’s performance of services under this agreement, express or implied, and Bennett hereby disclaims the implied warranties of merchantability and fitness for a particular purpose.

3. In no event shall Bennett be liable for any loss of profits, loss of use, interruption of business or indirect, special, incidental or consequential damages of any kind in connection with or arising out of the furnishing, performance, use or failure of the Bennett equipment, software or services acquired from Bennett, the distributor or the user, whether alleged as a breach of contract or tortuous conduct, including negligence. Bennett’s liability hereunder for damages shall not, in any event, exceed the amounts paid by the buyer to Bennett for equipment, software or services as to which the claim arose.

4. No action arising out of any claimed breach of the Warranty Agreement or transaction under this Warranty Agreement may be brought by either party more than two (2) years after the cause of action has accrued.

5. Use of non-Bennett replacement parts, unless specified by Bennett, will void the equipment warranty. 6. This warranty only applies to Bennett equipment installed outside the United States of America and is non-transferable. 7. Failure to pay the Bennett invoice within stated invoice terms, covering the respective Bennett equipment purchased under this limited warranty

may, at Bennett’s discretion, void this limited product warranty. THE FOREGOING WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING, WITHOUT LIMITATION, THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

BENNETT PUMP COMPANY 1218 E. Pontaluna Road Spring Lake, MI 49456 Tel: 231-798-1310 Fax: 231-799-6202

Bennett International Limited Warranty for Dispensers and Pumps

Bennett Pump Company guarantees new Service Station Equipment manufactured by Bennett against defects in material or workmanship during the warranty period in accordance with the provisions stated below:

The Site Audit Report issued with all equipment must be completed and returned at time of installation to Bennett Pump Company, Spring Lake,

MI to initiate warranty.

Warranty service must be performed by the nearest Bennett Authorized Service Representative qualified to perform service on the defective

equipment. Only Authorized and Certified Service Representatives are allowed to perform warranty service. Use of service personnel other than qualified Bennett Service Representatives without prior approval by Bennett Pump Company will void payment of any warranty claims.

Labor and travel costs incurred while servicing Bennett equipment is not covered under this limited warranty.

Bennett equipment has been installed according to the manufacturer’s instructions and diagrams.

During the warranty period, Bennett Pump Company will, at its option, repair or replace defective parts returned to its factory, transportation

charges prepaid.

The manufacturer reserves the right to make changes in the design or to make additions

Form 1-1010-8 Rev B 10-20-14

47 107929 Rev E 04-24-17

Revision Log

Revision Date Description

A - -

B - -

C - -

D 9/22/14 -

E 4/24/17 Add International Warranty

48 107929 Rev E 04-24-17

Bennett 1218 E. Pontaluna Road, Spring Lake, MI 49456 USA 800-235-7618 ~ Outside USA 231-798-1310

[email protected] ~ www.bennettpump.com

bennett 3000 series mechanical

Documents