basorfil e-bfr en

1E-BFR

Cost Saving

Greater Safe Working Load

H65-66%

H105-50%

Space Saving

w w w . b a s o r . c o m

NOW

BEFORE

2 E-BFR

Safety edges to prevent cable damage.

Full Range of fast fixing accessories.

Innovative design patented by BASOR which offers:

• Greater flexure resistance.

• Greater Safe Working Load.

• Excelent aesthetic finish.

Quicker and easier assembly:

• The trays can be moulded with a simple manipulation to obtain complicated changes in directions.

• The cuts have to be performed with aymmetrical-cut wire cutters.

• The cut has to be performed as near as possible to the intersection of the wires, in order to obtain a clean cut and a good assembly.

2

1

3

4

CABLE CAPACITY (cm2)

B(mm) H65 H105

60 21 -

100 43 -

150 72 -

200 100 186

300 156 291

400 212 396

500 268 501

600 324 606

1

* See the technical annex of the catalogue B03 or ask us for technical advice.

2

3

3

2 7UNE-EN 61537

150ºC

-50ºC

UNE-EN 61537

M0

UNE-EN 61537UNE 23727

UNE-EN 61537

*L > 100 m

1

2

Stackable Wire-Mesh Cable TraysBASORFILSCM

E-BFR

3E-BFR

H65B H EZ HDG

DESCRIPTION mm mm REF. kg/m REF. kg/mBASORFIL E-BFR 100X65 100 65 2/7305 0,77 2/7326 0,83

BASORFIL E-BFR 150X65 150 65 2/7306 0,82 2/7327 0,89

BASORFIL E-BFR 200X65 200 65 2/7307 1,06 2/7328 1,15

BASORFIL E-BFR 300X65 300 65 2/7308 1,57 2/7329 1,69

BASORFIL E-BFR 400X65 400 65 2/7309 1,90 2/7330 2,05

BASORFIL E-BFR 500X65 500 65 2/7310 2,46 2/7331 2,65

BASORFIL E-BFR 600X65 600 65 2/7311 2,83 2/7332 3,05

To assembly E-BFR H65 cable trays use a quick joint BFR 35 E-BFR 65/105 (2/7271 in EZ, 2/7272 in HDG) on each side of the cable trays. For trays wider than 300 an aditional bolt-staple set shall be used as central union joint (2/4364 in EZ, 2/4360 in HDG).

H-7

B + 15

50

100L = 3 m

H105B H EZ HDG

DESCRIPTION mm mm REF. kg/m REF. kg/mBASORFIL E-BFR 200X105 200 105 2/7312 1,57 2/7333 1,69

BASORFIL E-BFR 300X105 300 105 2/7313 1,90 2/7334 2,05

BASORFIL E-BFR 400X105 400 105 2/7314 2,46 2/7335 2,65

BASORFIL E-BFR 500X105 500 105 2/7315 2,83 2/7336 3,05

BASORFIL E-BFR 600X105 600 105 2/7316 3,20 2/7337 3,45

To assembly E-BFR H105 cable trays use a quick joint BFR 65/105 E-BFR 105 (2/6217 in EZ, 2/6219 in HDG) on each side of the cable trays. A quick joint BFR H35 E-BFR 65/105 can be added as an extra reinforcement (optional).

B + 18

H -

4 25

50

100

L = 3 m

QUICK JOINTSEZ HDG

DESCRIPTION REF. kg/ud REF. kg/udQUICK JOINT BFR 65/105 E-BFR 105 2/6217 0,03 2/6219 0,03

QUICK JOINT BFR 35 E-BFR 65/105 2/7271 0,04 2/7272 0,04

Fast fix couple for BASORFIL trays, BF, BFR and E-BFR. Screwless.

Simple and fast to assemble. For a perfect fit, tighten the tabs withs pliers.

34

464412


E-BFR

BOLT-STAPLE SETEZ HDG

DESCRIPTION REF. kg/ud REF. kg/udBF BOLT-STAPLE SET 2/4364 0,03 2/4360 0,03

It consists of a BF-bolt set and a BF-staple.

Bolted coupler for all BASORFIL tray series.

20

6

28

18

4 E-BFR

STBPG HDG

DESCRIPTION REF. kg/ud REF. kg/udSTB 2/0356 0,14 2/0366 0,14

Take-off plate for rigid pipes 16, 20 and 25.

You can see the Insulating Conduit Cable Conduction Systems (SCP) in our products catalogue B02.

SSC CENTRAL SUSPENSIONEZ HDG

DESCRIPTION REF. kg/ud REF. kg/udSSC CENTRAL SUSPENSION 2/2064 0,03 2/0363 0,03

The SSC allows to fix the tray to the ceiling with a M8 threated rod (2/3397 - EZ).

Each attachment point requires two SSC (upper an lower), one rod and two M8 DIN 6923 nuts (0/0338 in EZ, 0/0338 in HDG).

Also can be used as a fastener between wire mesh trays and any horizontal support with a B1 bolt set (2/4356 in EZ, 2/6826 in HDG).

BF STAPLEEZ HDG

DESCRIPTION REF. kg/ud REF. kg/udBF STAPLE 2/0337 0,01 2/0339 0,01

It is used to mount the divider profile.

BF BOLT-NUT SETPap EZ HDG

DESCRIPTION Nm REF. kg/ud REF. kg/udBF BOLT-NUT SET 4 2/4362 0,02 2/7132 0,02

Patented BF-Bolt and a nut DIN 6923. The BF-Bolt is specifically designed by BASOR to form a perfect fit between the wire trays.

20

6

23

21

28

18

8x8

6

50

40

60

9

2123,5

29

81 14

127


E-BFR

MULTI UNION JOINTPG HDG

DESCRIPTION REF. kg/ud REF. kg/udMULTIUNION JOINT 2/0357 0,05 - 0,05

Supplement used in the workplace for construction of accessories (vertical inside/outside, horizontal bend, reduction, etc.)

1650

025

18x7.5

5E-BFR

UNIVERSAL SUPPORT BOXPG HDG

DESCRIPTION REF. kg/ud REF. kg/udUNIVERSAL SUPPORT BOX 2/0358 0,28 2/0368 0,28

For fixing the watertight boxess of the leading manufacturers: Legrand, Gewiss, Eunea, etc.

For fixing:Square shape 29-70 (mm).Rectangular shape 79x50, 98-128x50, 15-55x82 (mm).Straight line from 30 to 147 (mm).

104

200

5

715029

112144

5

2880 72 50 25

35x7,5

12x8

25

8,5

DROP-OUT PLATEPG HDG

DESCRIPTION REF. kg/ud REF. kg/udDROP OUT PLATE BF/BFR 2/6451 0,18 2/6452 0,20

To assemble drop-out plate with cable trays use a SSC, a M8x25 DIN 933 bolt (0/0310 in EZ) and a DIN 6923 nut (0/0338 in EZ).

148

9

176

R100

DIVIDER PROFILE PSH PG HDG

DESCRIPTION mm REF. kg/m REF. kg/mPS 35 35 2/3476 0,23 2/3479 0,29

PS 60 60 2/2066 0,34 2/3480 0,43

PS 80 80 2/3477 0,46 2/3481 0,63

PS 100 100 2/3478 0,56 2/3482 0,76

One B1 bolt set (2/4356 in EZ, 2/6826 in HDG) and one BASORFIL staple (2/0337 in EZ, 2/0339 in HDG) are required to fix the divider profile to the wire-mesh cable tray every 500 mm.

The divider profile allows better organization of cables.

It is strongly recommended its use in systems with electromagnetic compatibility issues to separate data and power cables.

2550

20x8

20

H-5

L = 3 m

HORIZONTAL BEND VERTICAL INSIDE LEVEL CHANGE

Multijunction joint can be used to reinforce

the accessories.


the accessories.


the accessories.

VERTICAL OUTSIDE+INSIDE


E-BFR

6 E-BFR

C-SHOB e SWL PG HDG

DESCRIPTION mm mm (kg) REF. kg/ud REF. kg/udFAST FIXING SUPPORT C-SHO 100 1,5 98 2/7230 0,38 2/7239 0,41

FAST FIXING SUPPORT C-SHO 150 2 90 2/7231 0,43 2/7240 0,47



SHO/SHOT SUPPORTING PIECE - 2 - 2/6240 - 2/6318 -

No aditional pieces are required to fix wire-mesh cable trays. The design of the brackets, with the T-shaped fixing flap, allows a resistant and easy installation of the trays BASORFIL BFR/BF only using a flat baded screwdriver.

For anchoring to the wall, a SHO supporting piece (2/6240 in EZ, 2/6318 in HDG) is necessary. If SHO supporting piece is not used the SWL values fell by 12% and the profile can crash when the anchor presses it.

C-SHOTB e CTA PG HDG

DESCRIPTION mm mm (kg) REF. kg/ud REF. kg/udFAST FIXING SUPPORT C-SHOT 100 100 1,5 98 2/7235 0,43 2/7244 0,48

FAST FIXING SUPPORT C-SHOT 150 150 2 90 2/7236 0,62 2/7245 0,67



SHO/SHOT SUPPORTING PIECE - 2 - 2/6240 - 2/6318 -


For anchoring to the wall, a SHO supporting piece (2/6240 in EZ, 2/6318 in HDG) is necessary. If SHO supporting piece is not used the SWL values fell by 12% and the profile can crash when the anchor presses it.

SVOB e CTA PG/EZ HDG

DESCRIPTION mm mm (kg) REF. kg/ud REF. kg/udSVO 100 SUPPORT 100 1,5 250 2/3630 0,24 2/6280 0,26

SVO 150 SUPPORT 150 1,5 200 2/1073 0,24 2/1078 0,26

SVO 200 SUPPORT 200 2 294 2/1074 0,37 2/1079 0,39

SVO 300 SUPPORT 300 2 235 2/1076 0,49 2/1081 0,52

SVO 400 SUPPORT 400 2 161 2/3629 0,55 2/5719 0,59

SVO 500 SUPPORT 500 2 115 2/1077 0,67 2/1082 0,72

SVO 600 SUPPORT 600 2 87 2/5941 0,78 2/5720 0,84

M8 THREADED ROD - - - 2/3397 0,35 - -

M8 DIN 6923 NUT - - - 0/0338 0,01 0/0348 0,01


To mount the SVO support to ceiling, 2 M8 threaded rods, 4 M8 DIN 6923 nuts and 2 anchorages plugs for threaded rod BASORFIX CM8x30 are needed.

B + 92B + 112

113

2550

52

e 5020x9

175

20

113

B + 112

2550

52

255020x9

20x9

52

20

e

B +

100

2550

20x9

Supports for Wire-Mesh Cable TraysBASORSUPPORTSCM

7E-BFR

C-PC+C-SR + SPLIT PIN DIN94 DETAIL PC CLICK PORF.+HEAD+C-SR C-PC+HEAD+C-SR+REINFORCEMENT

PC CLICK HEADe PG

DESCRIPTION mm REF. kg/udPC CLICK HEAD 2 2/7270 0,24

SR/PC M8 BOLT SET - 2/6793 0,24

8x80 DIN 94 SPLIT PIN - 2/7297 0,37

The PC click head allows the construction of ceiling supports with PC profile (with single or double profile) using bolts or split pins.

To fix the PC profile to the PC click head two bolts or split pins are required.

Also, with 2 additional heads and one additional profile, 45 degrees reinforcements can be mounted to increase the resistance of the ceiling support.

To attach the PC click head to the rear face of the PC and built the reinforcements, 2 B2 bolt sets (2/4926 in EZ) are needed.

C-SR SUPPORTe B H A SWL PG

DESCRIPTION mm mm mm mm kg REF. kg/udC-SR 200 SUPPORT 1,5 200 65 30 102 2/7264 0,36

C-SR 300 SUPPORT 1,5 300 65 30 90 2/7265 0,49

C-SR 400 SUPPORT 1,5 400 100 60 159 2/7266 0,81

C-SR 500 SUPPORT 1,5 500 100 60 134 2/7267 0,97

C-SR 600 SUPPORT 1,5 600 100 60 117 2/7268 1,14

SR/PC M8 BOLT SET - - - - - 2/6793 0,24

8x80 DIN 94 SPLIT PIN - - - - - 2/7297 0,37

The C-SR support is designed for assemblies with PC or PC click profile using 2 SR/PC M8 bolt sets or 2 8x80 DIN 94 split pins (only one bolt set/pin on models 200 and 300).

No additional pieces are required to fix the wire-mesh cable trays. The design of the brackets, with the T-shaped fixing flap, allows a resistant and easy installation of the trays BASORFIL BFR/BF only using a flat baded screwdriver.

PC CLICK PROFILEe B H PG

DESCRIPTION mm mm mm REF. kg/udPC CLICK PROFILE 2 58 35 2/7269 1,75

The PC click profile, and its wide range of accessories (PC click head, articulated bracket, pins, etc.) allow a large variety of celing, wall and tunnel assemblies.

Supported on the open face of the profile for mounting horizontal supports C-SR

Supported on the wings of the profile for mounting horizontal supports SCR and SRB.

130

8,56063

90

25x11

95

e

B + 50

H A 8,5

50

53

50 20x9

9

B

H

e

30

20x9 8,5

3000

30

Supports for Wire-Mesh Cable TraysBASORSUPPORTSCM

e - m a i l : b a s o r @ b a s o r. c o m

basorfil e-bfr en

Documents