basic guide for genex assistant 3.5.pdf
TRANSCRIPT
Technology changes. Communication lasts 1
Basic Guide for
GENEX Assistant 3.5
HUAWEI TECHNOLOGIES CO., LTD.
Technology changes. Communication lasts 2
1. How to make a New Project… (step 1)
Click on New Project (Ctrl+N)
OR
Technology changes. Communication lasts 3
(step 2)
Insert your project name
Browse your target location
to save
Check your binning
Then…click “OK”
Technology changes. Communication lasts 4
2. How to load the logfiles…(step 1)
Click on Logfile Manager (Ctrl+F)
Technology changes. Communication lasts 5
(step 2)
Click “Add Logfile…” and browse
your location for target logfiles
Technology changes. Communication lasts 6
(step 3)
choose all your target logfiles and
click “Open”
Technology changes. Communication lasts 7
(step 4)
wait until all the logfiles loaded
and click “OK”
Technology changes. Communication lasts 8
3. How to group your test cases… (step 1)
Click on Analysis Group Manager (Ctrl+G)
Technology changes. Communication lasts 9
(step 2)
click “Add”
Technology changes. Communication lasts 10
(step 3)
step 1: insert the name of your test cases
step 2: select the test cases you want to grouping
step 3: click the arrow button in the middle and your selected test cases will move to the right
step 4: click “OK”
1
23
4
Note: In this cases, the Group Name is “2G UL” and the test cases for 2G UL is from MS1
based on the logfiles name [Q3_C4_SC02_2G_L4_MS1_UL_MS2_IDLE_SCANNER].
That’s why MS1 was moved to the right
Technology changes. Communication lasts 11
(step 4)
then click “OK”
Technology changes. Communication lasts 12
(step 5)
all the test cases you grouped will show here
Technology changes. Communication lasts 13
4. How to “Run” the logfiles…(step 1)
right click on “Analysis Group”, and click on “Run Analysis”
Technology changes. Communication lasts 14
(step 2)
Click “OK”
Technology changes. Communication lasts 15
(step 3)
wait until all the logfiles
finish to analyze
Technology changes. Communication lasts 16
(step 4)
this “KPI Result” table will appear once your
logfiles have been finish to analyze
Technology changes. Communication lasts 17
5. How to load the map… (step 1)
click on “View Map”
Technology changes. Communication lasts 18
(step 2)
click on “Layer Control” symbol
Technology changes. Communication lasts 19
(step 3)
Click “Add” and browse the location
of your map (.tab) files
Technology changes. Communication lasts 20
(step 4)
then click “OK”
Technology changes. Communication lasts 21
6. How to show the plotting…(step 1 - 4)
step 1: go to “Project” sidebar and select your grouped test cases
step 2: make sure your test cases is correct before you choose the plotting value
step 3: expand the features in the group
1
2
3
step 4: drag your chosen value into the map
Technology changes. Communication lasts 22
7. How to see the legend…(step 1)
click on “Enable/disable Legend” symbol
Technology changes. Communication lasts 23
(step 2)
then click “OK”
Select “Legend With Count And Percent”
Technology changes. Communication lasts 24
(step 3)
The legend will show like this
Technology changes. Communication lasts 25
8. How to modify the legend… (step 1)
Expand the “Data Layer” checkbox
click on “Map Layers” at the right side
of your GENEX Assistant
Technology changes. Communication lasts 26
(step 2)
Right click on the target legend
that you want to modify
Choose and click “Modify Legend”
Technology changes. Communication lasts 27
(step 3)
double click on the legend
you need to modify
Modify the legend that you need
Then, click “OK”
1
2
3Then, click “OK”4
Technology changes. Communication lasts 28
9. How to load Engineering Parameter… (step 1)
go to “Engineering Parameter” toolbar and choose which parameter
you want to load (GSM/WCDMA/LTE) depending on your project
Technology changes. Communication lasts 29
(step 2)
click on the GSM/WCDMA/LTE and click on “View Engineering Parameter”
Technology changes. Communication lasts 30
(step 3)
click on “Import BTS Config file” symbol
Technology changes. Communication lasts 31
(step 4)
then click “OK”
Browse your Engineering Parameter (.csv) file
Technology changes. Communication lasts 32
(step 5)
Make sure all the column name is synchronize
Then, click on “Apply the BTS Config” symbol
Technology changes. Communication lasts 33
(step 6)
Then, click “No”
wait until your Engineering Parameter loaded and
the below message box will appear once the process
is finish.
Technology changes. Communication lasts 34
10. How to edit Cell Label… (step 1)
right click on the map and click
on “Edit Cell Label”
Technology changes. Communication lasts 35
(step 2)
choose the value for
“DataSet:” and “Field” you
need to view.
then , click “OK”
Technology changes. Communication lasts 36
11. How to copy the map… (step 1)
click on this symbol to copy the current map
and paste on your document
Technology changes. Communication lasts 37
12. How to region the target analysis…(step 1)
click on “Add Region” symbol
Technology changes. Communication lasts 38
(step 2)
draw the border for your region and double click at the end of the border you draw
Technology changes. Communication lasts 39
(step 3)
click on “Save Region” symbol
Technology changes. Communication lasts 40
(step 4)
put the name for the region
cropped
then , click “OK”
Technology changes. Communication lasts 41
(step 5)
go to “Project” sidebar, right click on “Query” and
click on “New Query” to create a query for region
cropped
Technology changes. Communication lasts 42
(step 6)
Put the name for the query
Thick on the selected
region to use in the query
and click “Next”
Technology changes. Communication lasts 43
(step 7)
1
2
4
step 1: expand the features in “Available IE” box to
select the value you need to use in the region
step 2: select the value you need
step 3: click the arrow button in the middle and your
selected value will move to the right
step 4: click “OK”3
Note: In this cases, the value selected is “ServCellID”, “RxLev Sub” and “RxLev Qual” only
Technology changes. Communication lasts 44
(step 8)
Expand the “Query” and you can see the value
added to the region (only “ServCellID”, “RxLev
Sub” and “RxQual Sub” is shown). Only the plot
and value inside the region will be shown. All
plotting and value outside the region will be
excluded/dissappear.