automated, hydraulic laboratory press · automated, hydraulic laboratory press learn more about the...
TRANSCRIPT
AUTOMATED, HYDRAULIC LABORATORY PRESS
Learn more about the X-Press!Scan this code with the QR Reader on your smart phone or visit www.spexsampleprep.com/xpress
Pressing & Pelletizing
Compact bench top design
Presses Samples in minutes and accepts all standard die sets.
Programmable LCD touch screen interface.
Programmable parameters include pressure, dwell time and release time.
Safety features include a safety interlock that holds the door of the chamber in a locked position during operation. Also features an automatic pump shut-off safety valve.
Cement, Rocks, Minerals, Soils, Ceramics, Glass and Pharmaceuticals
The X-Press® is a 35-ton (31.8 metric ton) hydraulic laboratory pellet press that is ideal for accurate and repetitive pressing of sample pellets for XRF, IR and other analytical techniques.
TYPICAL SAMPLES
FEATURES & BENEFITS
: :
: :
: :
: :
: :
SPECIFICATIONS
FORCE 0 - 35 TONS RAM PRESSURE DAYLIGHT 2.0 - 6.0 in. (5 - 15 cm)
DWELL TIME 0 - 10 minutesSCREW ADJUSTMENT 3.5 in. (9 cm)
RELEASE TIME 0 - 10 minutes DIMENSIONS 20.0 in. (50.8 cm) high x 13.0 in. (33.0 cm) wide x 22.5 in. (57.2 cm) deep
PLATEN MOVEMENT 1 in. (25 mm) VOLTAGE 115V/60Hz or 230v/50 Hz
PLATEN SIZE 3.25 in. (8 cm) diameter WEIGHT Approximately 160 lbs (73 kg)
X-PRESS ACCESSORIES
Evacuable pellet die sets are available from 10 to 40 mm diameter. Set includes evacuable die body, base, plunger, two polished steel pellets, O-ring vacuum seals, and knock-out ring for sample disk extraction.
Used with the Evacuable Pellet Die Set and any PrepAid® sample binder. Allows easy preparation of XRF disks with binder matrix supporting a layer of sample.
BINDERSPELLET DIE SETS
SLEEVE-AND-PLUNGER SET
Visit www.spexsampleprep.com/xpress for the full range of accessories.
Paraffin and cellulose binders are ideal for samples which crumble or ablate after pressing. They blend quickly and completely with samples at 10-20% by weight to form XRF sample disks.
SPEC-CAPS®Shallow, thin-walled aluminum cap for reinforcing XRF pellets. Commonly used in the production of pressed power sample disks for XRF but also used for OES and other analytical techniques.
ALSO AVAILABLE: 25-TON AIR-ACTUATED BENCH PRESS®
This 25-ton (22.7 metric ton) air-actuated laboratory pellet press accepts all standard pellet die sets. It is manually controlled and ideal for the repetitive pressing of sample pellets for XRF, IR, and other analytical techniques. Typical samples include Cement, Rocks, Minerals, Soils, Ceramics and Pharmaceuticals. Its compact design is ideally suited for laboratory bench top applications and it can be operated off an air compressor or a tank of compressed air.
Features include:
Single push button operationNo hand-pumping or electrical hook-up is required
Pressure is easily measured with a dial and the pressure control valve can be set to produce repetitive, reproducible pressures.
: : : :
: :
Corporate HeadquartersSPEX SamplePrep15 Liberty StreetMetuchen, NJ 08840
Tel: 732-623-0465Fax: [email protected]
European DivisionSPEX CertiPrep Ltd2 Dalston GardensStanmore, Middlesex HA7 1BQ
Tel: +44 (0) 208-204-6656Fax: +44 (0) [email protected]