Julian Bowen Limited

Atlas Triple SleeperAssembly Instructions

VERSION: 161015

IMPORTANT - READ CAREFULLY - RETAIN

FOR FUTURE REFERENCE

02

PARTS

1

03

2

3

4

5

6

7

10

7

8

9

11

11

12

12

13

14

15

16

17

18

19

20

20

HARDWARE ED

G

64x

C

85x 4x 14x 12x

16x 1x 1x

H I J K

A

10x

B

4x4xA & B already attached

to Centre Leg Part 20

F

10x

L

6x

8

6x

M

2x

N

S a f e t y A d v i c ePlease take the time to carefully read through the whole of these instructions before

you commence.

Keep these instructions for future reference.

Unpack, inspect and check off all of the contents.

Please dispose of all packaging safely.

Small component parts could choke a child if swallowed.

We strongly recommend that you keep children well away from the work area.

It would be sensible to lay a sheet or blanket on the floor where you intend to work

to avoid scratching this product and to protect your floor.

This product is heavy. Take extreme care when lifting to avoid personal injury or

damage to the product.

Assemble the product as close to its intended final position in the room as possible.

HANDY HINT: If you keep the hardware in a bowl during assembly you will be less

likely to lose them.

04

Tighten firmly all the fittings when the assembly is complete.

The bed base is an integral and indissociable part of the bed.

WARNING: High beds and upper bed of bunk beds are not suitable for children

under six years due to the risk of injury through falls.

It is not safe to use this product if any part of the structure is missing or broken.

Children could strangle themselves with articles, such as ropes, strings, cords,harnesses

and belts attached to or hung on this product.

WARNING: Children can become trapped between the bed and the wall. To avoid risk

of serious injury the distance between the top safety barrier and the wall shall not

exceed 75mm or shall be more than 230mm.

The largest size of the mattress recommended is : 190 x 91 x 20cm/190 x 131 x 22cm.

The bed has been tested to ensure compliance with BS EN 747-1:2012 + A1:2015.

I m p o r t a n t I n f o r m a t i o n

155cm

201.5cm

161.5cm

ATLAS TRIPLE SLEEPERProduct Code - ATL003

Distributed by: Julian Bowen Limited

Bentick House,

Park Lane Business Park,

Kirkby-in-Ashfield,

Notts, NG17 9LE

Factory ID: Manufactured in China

Date of Manufacture: Jun 2015

CERTIFICATION LABEL

This bunk bed model has

been tested by an independent

laboratory and is in compliance

with EN 747-1:2012 +A1:2015

- Standard Consumer Safety

Specification For Bunk Beds

WARNING : This upper bed is not suitable for children under six years

1

2

05

1

3

x8

8

11

CD

D

C

x16

I

2

4

8

11

x4

F

J

11

5

6

7

7

Please Do Not Fully Tighten Bolts Until Frame Is Fully Assembled

4x

K

1 2

3 4

C

H

Jx58

1415

3

06

1312

12

E

D

G

F

12x

J

G

4

B

A

4xJ

K

2xM

5

07

x3

x3

F

J

F

J

JC

x1

619

19

19

L

L

L

J

H

H

H

16

17

18

18

18E A

A

A

E

E

E

E

E

J

J

2x

N

16 17

7

08

WARNING:

THE MATRESS

SURFACE MUST NOT

BE ABOVE THIS LINE

CJ

x2

Urgent WarningWhen correctly adjusted the centre support legs on this product should be raised by 5mm from

the floor with the added weight of the mattress and bedding.

This bed may fail if it is used on a wooden floor WITHOUT the use of non slip pads on all support

legs and bed posts.

If the bed is to be moved, carefully lift the product rather than dragging to ensure that the centre

legs do not become twisted and buckle.

09

G e n e r a l C a r e

Wipe clean with a slightly damp soft cloth.

Avoid the use of all household cleaners and abrasives.

When moving your furniture, carefully lift into place.

Never drag or push the pieces across the floor as this

will cause damage to the joints and could result in failure to

the product that will invalidate the warranty.

R e c o m m e n d a t i o n s

Periodical re-tightening of fixings.

W a r n i n g

This unit is heavy. Please use an assistant when lifting.

N o t e s

Weʹve tried to make this piece of furniture as easy to

assemble as possible.

In the unlikely event that you have problems putting

it together or have damaged or missing pieces,

please contact our customer services on 01623 727374

Julian Bowen Limited

Bentinck House, Park Lane Business Park, Kirkby-in-Ashfield, Notts, NG17 9LE

www.julian-bowen.co.uk