assembly instructions ducosun ellips...2 assembly mi ducosun ellips 19.06.19 14 2.1 the term panel,...
TRANSCRIPT
Assembly instructions
19/06/2019
DucoSun Ellips
CONTENT
1. Parts Breakdown
2. Assembly
2
Parts Breakdown1
19.06.19
Spring-loaded pin
(S5000013)
(DC030161)
Locating pin
(S5000014)
(DC030159)
Hexagon head bolt
M6 x 35, to DIN 933
(G0000192)
(PT040130)
M6 self-locking hexagon nut
DIN 985
(G0000164)
(PT030347)
M6 washer
DIN 125 Form A
(G0000175)
(PT030346)
Hexagon nut M6
DIN 934
(G0000167)
(PT030299)
MI DucoSun Ellips
3
Parts Breakdown1
19.06.19
C-clip Ø 15mm
Thickness : 6mm
(G0012015)
(PT040001)
Collar bushing
MFM-0610-04
(G0012011)
(PT030344)
C-clip Ø 15mm
Thickness : 12mm
(G0012016)
(PT040002)
Collar bushing
MFM-0610-06
(G0012012)
(PT040132)
C-clip Ø 15mm
Thickness : 18mm
(G0012017)
(PT040003)
Collar bushing
MFM-1420-15
(G0012009)
(PT040080)
MI DucoSun Ellips
4
Parts Breakdown1
19.06.19
T-head bolt
M8 x 20
(G0000150)
(PT010003)
Hexagon head bolt
M6 x 16, to DIN 933
(G0000190)
(PT040138)
Flat washer M8
DIN 125 Form A
(G0000174)
(PT030255)
M6 x 30
DIN 7500
(G0000113)
(PT030316A)
Self-locking hexagon nut M8
DIN 985
(G0000162)
(PT040137)
Hex washer head self drillscrew
DIN 7504 Form K
(G0000300)
(PT040015A)
MI DucoSun Ellips
5
Parts Breakdown1
19.06.19
Type 100 Ellips blade
(P1143010)
Type 150 Ellips blade
(P1157010)
Hexagon head bolt
M6 x 25, to DIN 933
(G0000186)
MI DucoSun Ellips
6
Parts Breakdown1
19.06.19
Type 200 Ellips blade
(P1143010)
Type 350 Ellips blade
(P1154810)
Type 250 Ellips blade
(P1157010)
Type 400 Ellips blade
(P1144510)
Type 300 Ellips blade
(P1143710)
MI DucoSun Ellips
7
Parts Breakdown1
19.06.19
Type II 200E end cap
(G0001761)
(PT030107A)
Type II 250E end cap
(G0001921)
(PT050023)
Type II 300E end cap
(G0001762)
(PT030106D)
Type II 350E end cap
(G0001764)
(PT040125)
Type II 400E end cap
(G0001763)
(PT030103C)
MI DucoSun Ellips
8
Parts Breakdown1
19.06.19
Type II 100E end cap
(G0002235)
(B0006156)
Type III 100E L.H. end cap
(G0002236)
(B0006163)
Type II 150E end cap
(G0002240)
(B0006151)
Type III 100E R.H. end cap
(G0002237)
(B0006160)
Type III 150E L.H. end cap
(G0002241)
(B0006149)
Type III 150E R.H. end cap
(G0002242)
(B0006142)
MI DucoSun Ellips
9
Parts Breakdown1
19.06.19
Clevis foot mounting bracket
(G0001744)
(PT040117A)
Connection profile
27/18
(P1154010)
Motor bracket
(G0001746)
(DC040090)
Mullion support profile
60/100
(P1153610)
Type III 200E L.H. end cap
(G0001771)
(PT030108B)
Type III 200E R.H. end cap
(G0001776)
(PT020327C)
MI DucoSun Ellips
10
Parts Breakdown1
19.06.19
Axle pin without spring action,
Ellips 150 series blade,
Ellips 100, Cubic 150
(S5000016)
axle pin with spring action, Ellips 150 series blade,
Ellips 100, Cubic 150
(S5000015)
Linear Motor
Picolo XL 200
stroke = 100tot 200mm
F=1200N V= 6mm/s
(G0001748)
Linear Motor
Picolo XL 300
Slag = 200 tot…300mm
F=1200N V= 6mm/s
(G0000278)
MI DucoSun Ellips
11
Parts Breakdown1
19.06.19
Type III 250E L.H. end cap
(G0001923)
(PT050022)
Type III 250E R.H. end cap
(G0001924)
(PT050021)
Type III 300E L.H. end cap
(G0001772)
(PT030105E)
Type III 300E R.H. end cap
(G0001777)
(PT020328C)
Type III 350E L.H. end cap
(G0001774)
(PT040124)
Type III 350E R.H. end cap
(G0001779)
(PT040123)
MI DucoSun Ellips
12
Parts Breakdown1
19.06.19
Type III 400E
L.H. end cap
(G0001773)
(PT020330C)
Type III 400E
R.H. end cap
(G0001778)
(PT030109D)
C-clip tool
(K0001190)
(PT040134)
Spacer
27/18 series connection profile
(G0001747)
(PT040149)
Bottom clevis foot mounting
LBN-20/25
(G0001745)(DC040058)
MI DucoSun Ellips
Assembly2
1319.06.19MI DucoSun Ellips
Assembly2
1419.06.19MI DucoSun Ellips
2.1 The term PANEL, definition of a PANEL
• A panel is bounded by 4 points fixing it back to the supporting structure behind.
• These 4 fixing points are distributed in pairs over two distinctive, parallel mullion support profiles.
Two panels can be mounted either next to each other and/or above and below each other.
2 PANELSNext to
each other
4 PANELSNext to and above
one another
2 PANELSNext to
each other
2 PANELSAbove/below
each other
Assembly2
1519.06.19MI DucoSun Ellips
2.2 Operating a PANEL
•When the blades are running horizontally, either adjacent or stacked panels can be operated by a single
actuator.
•The calculation program allows to determine the size and the number of panels.
•When the blades are mounted vertically, only ADJACENT panels can be operated by a single actuator.
•In these cases, the actuator assembly is fitted at the BOTTOM.
•It is important that the circlip of the lower bearing point BE fitted to the lower bearing point.
•Here again, the calculation program helps determine the size and number of panels that can be operated by a
single actuator.
•In these cases, it is recommended that the actuator be mounted horizontally and therefore be covered to provide
shelter.
•Make sure that this housing is provided with an adequate number of cooling fins (for removal of the heat
generated by the actuator).
•Vertical and horizontal blade mounting arrangements use identical components.
•The assembly and the fitting of a vertical system with horizontal runs of blades in two adjacent panels, follow
below.
Assembly2
1619.06.19MI DucoSun Ellips
Preparing the 60/100 series mullion support profile (P1153610)
Cutting the profile to length.
Assembly2
1719.06.19MI DucoSun Ellips
Preparing the 60/100 series mullion support profile (P1153610)
Drilling 20 mm diameter holes (+0/-0.15) at the specified centre-to-centre distances
X
Y=2
3m
m Blade pitch
Xmin = (width of the blade)/2 + 10 mm
Assembly2
1819.06.19MI DucoSun Ellips
Preparing the 60/100 series mullion support profile (P1153610)
Fitting the MFM-1420-15 collar bushing (G12009) with gentle taps from a hammer
Assembly2
1919.06.19MI DucoSun Ellips
Fitting and aligning the 60/100 series support mullion (P1153610)
Assembly2
2019.06.19MI DucoSun Ellips
• Maximum SPANS
BLADE At windload
600Pa
(±115km/h)
At windload
800Pa
(±130km/h)
At windload
1250Pa
(±165km/h)
Ellips 100 beweegbaar2200 2000 1800
Ellips 150 beweegbaar2500 2200 2000
Ellips 200 beweegbaar 2600 2400 2100
Ellips 250 beweegbaar 3300 3100 2700
Ellips 300 beweegbaar 3300 3000 2600
Ellips 350 beweegbaar 3700 3400 3000
Ellips 400 beweegbaar 4000 3700 3200
Assembly2
2119.06.19MI DucoSun Ellips
Preparing the blades
• Cutting the profile to length.
As for 200, 250, 300, 350 and 400 Ellips series blades, cut these at least 30 mm but no more than 40 mm shorter
than the distance between the support mullions.
• CAUTION :
With 100 and 150 Ellips series blades, these should be cut 44mm shorter than the distance between the support
mullions.
Assembly2
2219.06.19MI DucoSun Ellips
Fitting a spring shaft into 200 up to 400 Ellips series blades
CAUTION : To fit a spring shaft in the blades, always use type III series end caps and fix it using M6 x 30 bolts (G113).
Always tighten the screws in the order shown.
In order to take up the play between the spring-loaded and the locating pins in the blade, ALWAYS secure them in
position using transparent silicone sealant.
Likewise, any play between the end caps and the axle pins, at the recess, should be removed using silicone sealant.
13
24
Assembly2
2319.06.19MI DucoSun Ellips
Fitting a fixed shaft into 200 up to 400 Ellips series blades
CAUTION : To fit a fixed shaft in the blades, always use type II series end caps and fix it using M6 x 30 bolts (G113).
Always tighten the screws in the order shown.
First the outer screws, then the rest.
In order to take up the play between the spring-loaded and the locating pins in the blade, ALWAYS secure them in
position using transparent silicone sealant. Likewise, any play between the end caps and the axle pins, at the recess,
should be removed using silicone sealant.
1
3
4 2
Assembly2
2419.06.19MI DucoSun Ellips
Fitting a spring shaft (S5000015) in type 100 and 150 Ellips blades (type III end cap)
CAUTION : To fit a spring shaft in a blade, always use type III series end caps and fix it using the
associated nut (G0002251). Always apply a drop of threadlock Loxeal 83/54.
Next, secure the assembly (end cap and spring shaft) using M6 x 30 bolts (G113).
When fitting, place one drop of Loxeal 83/54 on the extreme
end of the nut.
Tighten down with an A/F 19 mm spanner.
Assembly2
2519.06.19MI DucoSun Ellips
Fitting a spring shaft (S5000015) in type 100 and 150 Ellips blades (type III end cap)
CAUTION : It is important to always use spring shafts for type III end caps and to fix these using the associated
nut (G0002251). Secure the nut with a single drop of Loxeal 83/54 at all times.
Next, secure the assembly (end cap and spring shaft) using M6 x 30 bolts (G113).
Assembly2
2619.06.19MI DucoSun Ellips
Fitting a fixed shaft (S5000016) in type 100 and 150 Ellips blades (type II end cap)
CAUTION : To fit a fixed shaft in a blade, always use type II series end caps and fix it using an M10 washer
(G0000173) and a self locking nut M10 (G0000163).
Next, secure the assembled unit (type II series end cap and fixed shaft) using M6 x 30 bolts (G0000113).
Assembly2
2719.06.19MI DucoSun Ellips
Fitting the blades onto the support mullions
STEP 1: Hold the blade in an upright position and insert the extreme end holding the fixed shaft into
the bearing bush.
Assembly2
2819.06.19MI DucoSun Ellips
Fitting the blades onto the support mullions
STEP 2: Compress the spring shaft (use a screwdriver, if necessary) and insert it into the bearing bush.
Assembly2
2919.06.19MI DucoSun Ellips
Fitting the blades onto the support mullions
STEP 3: Fit all of the blades.
Assembly2
3019.06.19MI DucoSun Ellips
Fitting a C-clip to a blade
STEP 4: Fitting a circlip with a diameter of 15 mm and thicknesses of 6 mm, 12 mm or 18 mm
Insert the C-clip into the opening of the tool and then push the C-clip onto the spring shaft.
For the blades Ellips 100 and 150: a bearing of 12mm is only to be used at the motorised side, on the other side
a choice has to be made between 6mm, 12mm or 18mm depending on the necessary clearance.
Assembly2
3119.06.19MI DucoSun Ellips
Fitting an MFM-0610-04 collar bushing (G12011) and an MFM-0610-06 bushing (G12012) onto a
type III end cap
G0012012
G0012011
Assembly2
3219.06.19MI DucoSun Ellips
Fitting an MFM-0610-04 collar bushing (G12011) and an MFM-0610-06 bushing (G12012) onto a type
III end cap
Assembly2
3319.06.19MI DucoSun Ellips
Fitting the M6 x 35 hexagon bolt, the M6 washers, the M6 nut and the M6 lock nut
+/-4mm clearance
M6 nutM6 lock nut
Assembly2
3419.06.19MI DucoSun Ellips
Fitting the mounting bracket (G0001746) for linear actuator
Securing using M8 x 20 T-head bolts (G150), M8 washers (G174) and M8 lock nuts (G162)
Assembly2
3519.06.19MI DucoSun Ellips
Fitting the clevis foot mounting (G1744) for Ellips 200 till 400
• Insert the M6 x 16 bolts (G190), place an M6 washer (G175) and secure with an M6 lock nut (G164) ;
make sure there is proper clearance !
+/-4mm clearance
Assembly2
3619.06.19MI DucoSun Ellips
Fitting the clevis foot mounting (G1744) for Ellips 100 and 150
1) Insert the M6 x 25 bolts (G186), place an M6 washer (G175) and secure with an M6 lock nut (G164) ; make
sure there is proper clearance !
The same combination of bolts, nuts and washer is used to connect the distance holder (G0001747) with the
driving rod.
clearance +/-4mm
Assembly2
3719.06.19MI DucoSun Ellips
Securing the bottom clevis foot (G1745) to its mounting bracket (G1744)
1) Insert the M6 x 16 bolts (G190), place an M6 washer (G175) and secure with an M6 lock nut (G164) ;
make sure there is proper clearance !
Assembly2
3819.06.19MI DucoSun Ellips
Fitting the 27/18 series connection profile (P1154010) to the type III series end caps
1) Adjust all the blades to the same angle (90°).
2) Slide the 27/18 series connection profile (P1154010) over the M6 x 35 bolt heads securing the blades and over
the M6 x 16 bolts securing the clevis foot mounting bracket.
Assembly2
3919.06.19MI DucoSun Ellips
Fitting the 27/18 series connection profile (P1154010) to the type III series end caps
3) Slide the 27/18 series connection profile (P1154010) over the M6 x 16 bolt heads (G190) / or M6 x 25 (G186)
bolts securing the spacer of the 27/18 series connection profile (G1747).
Assembly2
4019.06.19MI DucoSun Ellips
Fitting the 27/18 series connection profile (P1154010) to the type III series end caps
4) Tighten the M6 nut (G167) to secure the M6 x 35 bolt (G192) to the 27/18 series connection profile (P1154010).
5) Tighten the M6 lock nut (G164) first and then fix the end plate to the 27/18 series connection profile.
M6 nut M6 lock nut
Assembly2
4119.06.19MI DucoSun Ellips
1) Locate the bottom clevis foot at distance Z (see calculation program) and lightly tighten the two bottom
lock nuts.
Dis
tan
ceZ
M6 lock nut
Assembly2
4219.06.19MI DucoSun Ellips
2) Secure the actuator when it is FULLY RETRACTED (that is, with blades closed) to the top mounting bracket.
3) If appropriate, adjust height Z by moving the bottom clevis foot until the 8 mm diameter spindle is a sliding fit.
Assembly2
4319.06.19MI DucoSun Ellips
4) Tighten all the M6 lock nuts intended to secure the clevis foot mounting brackets, ensure the actuator is fully
retracted (that is, with blades closed[) first and then fit it in place.
M6 lock nuts
Assembly2
4419.06.19MI DucoSun Ellips
Fitting the spacer (G1747) to the 27/18 series connection profile (for Ellips 200 – 400)
1) Insert the M6 x 16 bolts (G190), place an M6 washer (G175) and secure with an M6 lock nut (G164) ; make
sure there is proper clearance!
clearance +/-4mm
Assembly2
4519.06.19MI DucoSun Ellips
Fitting the spacer (G1747) to the 27/18 series connection profile (Ellips 100-150)
1) Bolt M6x25 (G186), lock nut M6 (G164), washer M6 (G175), make sure there is proper clearance!
clearance +/-4mm
Assembly2
4619.06.19MI DucoSun Ellips
Fitting the spacer (G1747) on top of the connection profiles
2) Insert the M6 x 16 bolts (G190) / M6 x 25 blots (G186) in the holes provided in the spacer of the 27/18 series
connection profiles, place an M6 washer (G175) and secure with an M6 lock nut (G164).
3) Locate the spacer in its correct position and tighten all the lock nuts.
Assembly2
4719.06.19MI DucoSun Ellips
Setting up the limit switches of the actuator
1) Adjusting the retracted and extended positions of the actuator
Adjusting ring for retracted
position
Adjusting ring for extended
position
Assembly2
4819.06.19MI DucoSun Ellips
Setting up the limit switches of the actuator
1a) Adjusting the retracted position of the actuator (fully retracted position)
Adjusting in the + direction will decrease the stroke length.
Assembly2
4919.06.19MI DucoSun Ellips
Setting up the limit switches of the actuator
1b) Adjusting the retracted position of the actuator (fully retracted position)
Adjusting in the - direction will increase the stroke length.
Assembly2
5019.06.19MI DucoSun Ellips
Setting up the limit switches of the actuator
2a) Adjusting the extended position of the actuator (fully extended position)
Adjusting in the + direction will increase the stroke length by moving the extended
position further away.
Assembly2
5119.06.19MI DucoSun Ellips
Setting up the limit switches of the actuator
2b) Adjusting the extended position of the actuator (fully extended position)
Adjusting in the - direction will decrease the stroke length by moving the extended
position closer.
Phase / Red
Black (R/nr2)Neutral (Blue)
Earth
(yellow/green
Neutral (Blue)
Black (V/nr3) Black(N/nr1)
2
5219.06.19
Adjusting the motor by means of the end of range contacts
2 c) Adjustment of the stroke length of the motor.
If with orders the stroke length is been given, Duco Projects will always test the motors and then adjust the strokelength.This happens on the basis of a setting set (G6002506). Like this we can guarantee 100% that the delivered motors workperfectly. The final adjustment always needs to happen on site. When there is no setting set available, then a 3-positions switch (blinds switch) can be used.
a) The grounding/earth (colour yellow/green) is connected with the grounding of the motor (colour yellow/green).
b) The 0 line (colour blue) is connected with (colour: black nr1 Marking N).
c) The phase (colour red) connect with clip L
d) Black Nr3 Marking V is connected with clip 1
e) Black Nr2 Marking R is connected with clip 2
Assembly
Assembly2
5319.06.19MI DucoSun Ellips
6) After fitting and adjusting the actuator, fit the actuator mounting bracket (G1746) using a 6.3 x 32 hexagon
bolt with collar (G300).
Assembly2
5419.06.19MI DucoSun Cubic-Linear
ATTENTION !!!!! Control actuators
The control of the motors can be done in various ways according to the wishes of the customer.
However, you should never connect the motors directly
HEREINLY SOME EXAMPLES:
-First, input parameters determine: what do I want to take into account for controlling?
-Determine output parameters: how do I control the motors?
-Choosing a correct control unit? Various suppliers (Elero, Somfy, ...) put steering systems on the market.
-Format wiring diagram
MOTORS NEVER TO BE SWITCHED PARALLEL !!
Assembly2
5519.06.19MI DucoSun Ellips
CE marking
Stick the CE marking in a visible place. Degrease the blade before you stick the sticker to obtain a good
adhesion.