–roduct specification - distronik · p roduct specification tft4213ml v0.0 r evision hi stor y v...

Product Specification

TFT-4213ML V0.0

Preliminary SpecificationFinal Specification

Module 36.6” Color TFT LCD Panel , Ultra Wide TFTModel Name TFT-4213 M L : 42inch1-3cut

Prepared by Date

Approved by Date

General Display Business Division / ANNAX-SUZHOU-China

Middle Luminance: 450cd/m^2

High Luminance : 1000cd/m^2 L:LG

Checked by Date

General Display Business Division / ANNAX-SUZHOU-China

Doc No.：TFT-LCD Spec. @ANNAX SUZHOU 1 Status: Release Save date: 2/13/2015 Copyright © ANNAX (Suzhou) Rail Systems Co., Ltd. All rights reserved.


TFT4213ML V0.0

Contents

NO. Item Page Contents 2

Revision History 31 Display Characteristics Summary 4 2 LCD Electrical Specification 6

2.1 Power Specification

2.2 LCD Interface connections

2.3 Signal Electrical Characteristics

2.3.1 DC Characteristics

2.3.2 AC Characteristics

2.4 Signal Characteristics

2.4.1 Pixel Format Definition

2.4.2 The input data format

2.5 Timing Characteristics

2.6 Timing diagram

6 6 7 7 7 8 8 9

10 10

3 Backlight Specifications 11 3.1 LED Driver Board connections

3.2 LED Driver Board connector drawing

3.3 LED Driver Board Characteristics

11 11 12

4 Reliability Test 12 5 International Standard 12

5.1 Safety

5.2 EMC

12 13

6 Precautions 13 6.1 Mounting Precautions

6.2 Operating Precautions

6.3 Electrostatic discharge control

6.4 Precautions for strong light exposure

6.5 Storage

6.6 Handling precautions for protection film

13 13 13 13 14 14

7 Packing 15 7.1 Pallet Ass’y

7.2 Packing Ass’y

7.3 Packing Form

15 16 16

#APPENDIX-1 17#APPENDIX-2 18



TFT4213ML V0.0

Revision History

Version/Date Page Old Description New Description Remark

V0.0 2015/01/15 - New Revision Release -



TFT4213ML V0.0 1. Display Characteristics Summary

Under 25°C condition:Items Unit Specifications Remark

Dimension

Parameter

LCD Electrical

LED Driver Electrical

Screen Diagonal [inch] 36.6 Note-1

Active Area: HA x VA [mm] 930 x 173 Appendix-1

Outline Size: HO x VO [mm] 973x207 Appendix-1

Pixels H x V - 1920 x 357

Pixel Pitch [mm] 0.4833 x 0.4833

White Luminance Code [c d/m^2] 450 Note-2

Uniformity [%] ≥80 Note-5

Color Temp. [K] ≥6500

Power Consumption [W] 44.4 Note-6

Contrast Ratio - 1500 Note-7

Aspect Ratio - 16:3

Viewing Angle [°] 170(H)160(V)

Response Time [ms] 5

Backlight - LED

Display Colors [colors] 16.7M

Weight [Kg] ≤2.8

LCD input Voltage [V] 12(type)

LCD input Current [A] 0.53(type)

LCD inrush Current [A] ≤3

LED Driver input Voltage [V] 12/24 Note-3

LED Driver input Current [A] ≤3.9 Note-4

Backlight Control - PWM

Operating Temp. [°C] 0-50

Environment

Note:

Storage Temp. [°C] -25-60 Note-8

Humidity [%] 10-90

(1). Active Area Dimension: Horizontal=HA, Vertical=VA

Screen Diagonal= Sqr(HA2+VA2)/25.4

(2). White Luminance Code:

M=450cd/m^2

H=1000cd/m^2

(3). LED Driver Board support 2 types of Voltage supply to work: DC12 and DC24

(4). LED Driver Current between M and High Luminance is different:

M=2.7A H=3.9A @12V

(5). Uniformity Measure: Min（5 points）/Max (5 points) X100%



TFT4213ML V0.0 And the setup shown in the figure below.

(6). Power consumption= PLCD+PLED (@PWM=100%) 3 files contain: L(when Lumina.350)/M(Lumina.500)/H(Lumina.1000)

(7). Contrast Ratio contains 3 types: L/M/H

(8). Temperature and relative humidity range are shown in the figure below.

2. LCD Electrical Specification 2.1 Power Specification



TFT4213ML V0.0 Parameter Symbol Value Unit Remark

Min. Typ. Max. LCD Power Supply Input Voltage VDD 10.8 12 13.2 [VDC] LCD Power Supply Input Current IDD - 0.53 0.69 [A] Note-1 LCD Power Consumption PVDD - 6.4 8.3 [W] Inrush Current IRUSH - - 4 [A]

Frame Rate Frequency 50 60 76 [Hz] CMOS

Interface Input High Threshold VIH 2 3.3 5 [VDC] Input Low Threshold VIL 0 - 0.8 [VDC]

Note: (1). All white Pattern @60Hz, IDD=1.2A (type)

2.2 LCD Interface connections Using Connector: FI-RE51S-HF or compatible Matching Connector: FI-RE51P or compatible Module connector (CN1) Pin configuration shown on the table below.

Pin No. Symbol Function Pin No. Symbol Function 1 NC NC 26 NC NC 2 NC NC 27 NC NC 3 NC NC 28 CH2_0- LVDS Channel 2,Signal0- 4 NC NC 29 CH2_0+ LVDS Channel 2,Signal0+ 5 BITSEL Low/GND:8bits; 30 CH2_1- LVDS Channel 2,Signal1-

High/Open:10bits 6 GND Power Ground [Must] 31 CH2_1+ LVDS Channel 2,Signal1+ 7 LVDSSEL Low/GND: JEIDA 32 CH2_2- LVDS Channel 2,Signal2-

High/Open:NS 8 NC NC 33 CH2_2+ LVDS Channel 2,Signal2+ 9 NC NC 34 GND Ground

10 NC NC 35 CH2_CLK- LVDS Channel 2,Clock- 11 GND Power Ground 36 CH2_CLK+ LVDS Channel 2,Clock+ 12 CH1_0- LVDS Channel 1,Signal0- 37 GND Ground 13 CH1_0+ LVDS Channel 1,Signal0+ 38 CH2_3- LVDS Channel 2,Signal3- 14 CH1_1- LVDS Channel 1,Signal1- 39 CH2_3+ LVDS Channel 2,Signal3+ 15 CH1_1+ LVDS Channel 1,Signal1+ 40 CH2_4- LVDS Channel 2,Signal4-

16 CH1_2- LVDS Channel 1,Signal2- 41 CH2_4+ LVDS Channel 2,Signal4+

17 CH1_2+ LVDS Channel 1,Signal2+ 42 NC NC

18 GND Power Ground 43 NC NC



TFT4213ML V0.0 19 CH1_CLK- LVDS Channel 1,Clock- 44 NC NC

20 CH1_CLK+ LVDS Channel 1,Clock+ 45 NC NC

21 GND Power Ground 46 NC NC

22 CH1_3- LVDS Channel 1,Signal3- 47 GND Power Ground

23 CH1_3+ LVDS Channel 1,Signal3+ 48 VDD Power Supply.+12V DC

24 CH1_4- LVDS Channel 1,Signal4- 49 VDD Power Supply.+12V DC

25 CH1_4+ LVDS Channel 1,Signal4+ 50 VDD Power Supply.+12V DC

51 VDD Power Supply.+12V DC

Note: NS and JEDIA model refer to # APPENDIX-2

2.3 Signal Electrical Characteristics 2.3.1 DC Characteristics of each signal are as following: Symbol Parameter Min Type Max Units Condition

VTH Differential Input High Threshold 100 - 600 [mV] VTL Differential Input Low Threshold -600 - -100 [mV]

|VID| Input Differential Voltage 200 400 600 [mV] VCM Differential Input Common Voltage 1.0 1.25 1.4 [V]

Note: (1) LVDS Signal Waveform shown as below:

2.3.2 AC Characteristics

VCM=1.25

VCM=1.25

Note-1

VTH- VTL=200MV



TFT4213ML V0.0 Description Symbol Min Max Unit Note

Max deviation of input clock Frequency during SSC

Max modulation frequency of input clock during SSC

Note: (1).Show as below:

2.4 Signal Characteristics 2.4.1 Pixel Format Definition

FDEV - ±3 % Note-1

FMOD 30 200 kHz Note-1

Following figure shows the relationship of the input signal and LCD pixel format:

357 Line



TFT4213ML V0.0 2.4.2 The input data format Note: R/G/B data7: MSB; R/G/B data 0: LSB O=”First Pixel Data” E=”Second Pixel Data”



TFT4213ML V0.0 2.5. Timing Characteristics

The input signal timing specifications are shown as the following table:Signal Item Symbol Min Type Max Unit

V-section

H-section

Period TV

Active TDISP

Blanking TBP+TFP+PWVS

Period TH

Active TDISP

Blanking TBP+TFP+PWHS

1100 1125 1149 TH

357 - - TH

20 45 69 TH

1060 1100 1200 TCLK

960 960 960 TCLK

100 140 240 TCLK

Clock Period TCLK

Frequency FREQ

Frame rate Frame rate F

Hsy-Fre.

Note: DE mode only

2.6 Timing diagram

11.1 14 18.2 ns

63 74.25 78 MHz

57 60 63 Hz

57.3 67.5 70 KHz



TFT4213ML V0.0 3. Backlight Specifications 3.1. LED Driver Board connections Using Connector: CI0114M1HRL-NH (CVILUX) CN2 Shown on the table below.

Pin Symbol Description 1 VDD Operating Voltage Supply, +12/24 DC regulated 2 VDD Operating Voltage Supply, +12 /24DC regulated 3 VDD Operating Voltage Supply, +12/24DC regulated 4 VDD Operating Voltage Supply, +12/24 DC regulated 5 VDD Operating Voltage Supply, +12/24 DC regulated 6 GND Ground 7 GND Ground 8 GND Ground 9 GND Ground

10 GND Ground 11 NC Not Connect 12 BL-ON ON: DC(2.0 – 5.5V) ; OFF: DC (0 – 0.8V) 13 NC NC 14 PWM/ADJ 0% - 100% Duty, open for 100%

3.2 LED Driver Board connector drawing



TFT4213ML V0.0 3.3. LED Driver Board Characteristics

Parameter Symbol Value（L/M/H） Unit Note Min. Typ. Max.

Driver Power Supply Input Voltage VDD - 12 - VDC Note-1 Power Consumption PLED - - 47 W Driver Power Supply Input Current IDD - - 3.9 A Note-2

ExternalPWM

Control Voltage

Input Duty ratio D_EPWM 0 - 100 % Frequency F_EPWM 150 - 2K HZ Input High Threshold VIH 2 3.3 5 VDC Input Low Threshold VIL 0 - 0.8 VDC

Operating Life Time MTBF 50000 - - Hour Note-3 Note:

(1). LED Driver Board support 2 types of Voltage supply to work: DC12 and DC24. (2). LED Driver Current between M and High Luminance is different:

M=2.7A H=3.9A @12V

(3). The Value of MTBF measured at Normal temperature environment (25°，60%Humidity)

4. Reliability Test Environment test conditions are listed as following table. (Refer to EN50155)

Items Required Condition Note Temperature Humidity Bias Ta=50 Degree,80%RH,300H

High Temperature Operation Ta=50 Degree,60%，300H Low Temperature Operation Ta=0 Degree,300H High Temperature Storage Ta=70 Degree,60%RH,300H Low Temperature Storage Ta=-25 Degree,300H

Shock Test(Non-Operating) 50G,20ms,Half-sine wave,(±X, ±Y, ±Z) Vibration Test(Non-Operating) 1.5G,(10-200HZ,P-P),30Min/axis(X,Y,Z)

On/Off test On-10s,Off-10s,30000cycles Contact Discharge: ±6KV,150pF,1s,8 points,25 times/point.

ESD Air Discharge:±8KV,150pF.1s, 8 points, 25times/point. 5. International Standard (Refer to the specifications of original screen) 5.1 Safety

1) UL 60950-1:2007; Standard for Safety of Information Technology Equipment Including electrical Business Equipment.

2) IEC 80950-1:2005; Standard for safety of international electro-technical commission. 3) EN 60950:2006+A11; European committee for electro-technical standardization

(CENELEC), EUROPEAN STANDARD for safety of information technology equipment including electrical business equipment.

5.2 EMC



TFT4213ML V0.0 1) ANSI C63.4”Methods of Measurement of Radio-Noise Emissions from Low-Voltage

Electrical and Electrical Equipment in the Range of 9KHZ to 40GHZ.” American National standards institute(ANSI),1992

2) C.I.S.P.R. “Limits ad Methods of Measurement of Radio interface Characteristics of information Technology Equipment.” International Special committee on Radio interface.

3) EN 55022 “Limits and Methods of Measurement of Radio interface characteristics of information Technology equipment.” European committee for electro-technical standardization.(CENELEC),1998.

6. Precautions Please pay attention to the followings when you use this TFT LCD module

6.1 Mounting Precautions (1). Please attach the surface transparent protective plate to the surface in order to protect the polarizer. Transparent protective plate should have sufficient strength in order to the resist external force. (2).You should adopt radiation structure to satisfy the temperature specification. (3).Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes deformations and color fading. (4).Do not open the case because inside circuits do not have sufficient strength.

6.2 Operating Precautions (1).The pike noise causes the mis-operation of circuits. It should be lower than following voltage: V=±200mV(Over and under shoot voltage) (2).Response time depends on the temperature (In low temperature, it become longer) (3).When fixed pattern are displayed for a long time, remnant image is likely to occur. (4).Brightness depends on the temperature. (In lower temperature, it becomes lower.) (5).Please do not set LCD on its edge. (6).Please do not give any mechanical and/or acoustical impact to LCM. Otherwise, LCM can not be operated its full characteristics perfectly.

6.3 Electrostatic discharge control Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that treatment persons are connected to ground through wrist band etc. And don’t touch interface pin directly.

6.4 Precautions for strong light exposure Strong light exposure causes degradation of polarizer and color filter.

6.5 Storage



TFT4213ML V0.0 When storing modules as spares for a long time, the following precautions are necessary

(1).Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the temperature between 5°C and 35°C at normal humidity. (2).The polarizer surface should not come in contact with any other object.

It is recommended that they be stored in the container in which they were shipped.

6.6 Handling precautions for protection film (1).The protection film is attached to the bezel with a small masking tape. (2).You can remove the glue easily. When the glue remains on the bezel surface or its vestige is recognized, please wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-hexane.



TFT4213ML V0.0 7. Packing 7.1 Pallet Ass’y

① ③

②

NO Description Spec. 1 Pallet Ass’y 1100x550x700 2 Pallet 1100x550x120 3 Band PP 4 Wrap -



TFT4213ML V0.0 7.2 Packing Ass’y

7.3 Packing Form Packing quantity in one box: 5pcs

NO Description Spec. 1 Bar-LCM TFT4213ML 2 STYROFOAM - 3 BOX 1030x260x220 4 Label 30x10(5ea)



TFT4213ML V0.0 #APPENDIX-1 Mechanism dimensions



TFT4213ML V0.0

#APPENDIX-2 LVDS Select : NS and JEDIA model: 8bits

Doc No.：TFT-LCD Spec. @ANNAX SUZHOU 18 Status: Release Save date: 2/13/2015 Copyright © ANNAX (Suzhou) Rail Systems Co., Ltd. All rights reserved. https://www.distronik.de

–roduct specification - distronik · p roduct specification tft4213ml v0.0 r evision hi stor y v...

Documents