1. Light fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: ALamp Type : 2 x 24 W Linear fluorescent T5, Color 830Mounting: RecessSpecified:Concord:marlin 0058870Detailed specification:Recess mounted luminaire with 2 x 24 W T5 linear fluorescent lamps color 830.Luminaire housing shall be made from sheet steel electrically welded and finishedwhite. The luminaire shall be provided with specular optic system of highperformance aluminum louver set within an involute central baffle system. An internalpolycarbonate foil shall soften the light distribution. The tri dimensional Bess opticshall ensure > 69%, Intensity of > 200 cd/klm at 0, and Imax of 410 c/klm at 30.The louver shall ensure very low brightness appearance. UGR values in both axes ofviewing shall be < 15 for all S/H ratios. The luminaire shall be supplied with lampsinstalled from factory and a protective peel off film that is to be removed aftercomplete installation of the luminaire. Connection of the luminaire to the mains shallbe via a rapid connect plug system. All high frequency control gear shall be laid outinternal to the luminaire. The luminaire shall be ENEC certified, F marked and glowwire tested to 960 C, and be provided with a separate earthing terminal. Theluminaire shall be Concord:marlin 0058870.Note : For luminaire with integral emergency kit, the kit shall consists of converterunit, charger circuit and Ni Cd batteries to ensure operation for 3 hours on mainsfailure. The luminaire shall be Concord:marlin 0058871.IP: 20Alternative approved :Zumtobel, Hoffmeister,CromptonLocation of use : Changing rooms 1

2. Light fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: BLamp Type : 1 x TC L 55 W Compact fluoresent, Color 830Mounting: RecessedSpecified:Concord:marlin 2037296Detailed specification:Recess mounted luminaire for use with 1 x TC L 55 W compact fluorescent lamps.Luminaire housing in sheet steel finished white, with satin polycarbonate wings and acentral panel of polycarbonate comprised of conical deglaring prisms to ensure glare< 1500 cd/m t and above 65. The lamps shall be located behind the central panel.All high frequency control gear shall be mounted internal to the housing and shall bepre wired upto the connector plug in socket. The luminaire shall be single point LG7compliant, and a reflector of micro pure aluminum shall ensure > 60%. Theprojection of the wings from the ceiling shall be limited to 50 mm. The dimensions ofthe luminaire shall not exceed 597 mm x 595 mm x 145 mm height. The luminaireshall be F marked; glow wire tested to 960C and provided with an earthing terminal.The luminaire shall be Concord:marlin 2037296.Note : For luminaire with integral emergency kit, the kit shall consists of converterunit, charger circuit and Ni Cd batteries to ensure operation for 3 hours on mainsfailure. The luminaire shall be Concord:marlin 2037297.IP: 40Alternative approved :RSL, Thorlux, CromptonLocation of use : Offices 2 3. Light fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: CLamp Type : 1 x TC TEL 26 W + 1 x T 16-R 22 W, Color 830Mounting: RecessedSpecified:Concord:marlin 2037420Detailed specification:Recess mounted luminaire system for use with 1 x 26W TC-TEL + 22 W T16-Rcompact fluorescent lamps. Luminaire shall be in aluminum and steel construction.The central lamps shall be supported in operation by an aluminum vacuummetallized reflector compliant to LG 7. A dished opal polycarbonate diffuser to ensurecompliance to LG 7 shall diffuse the light output of the 22 W lamp. All high frequencycontrol gear wired for single switching shall be located internal to the luminairehousing. The cutout diameter shall be limited to 275 mm and the height of theluminaire shall be limited to 147 mm. The projection of the diffuser from the line of theceiling shall be limited to 39 mm. The mounting of the luminaire shall be via 4mounting clips. The DLOR and ULOR of the luminaire shall be at least 53% and 4 %respectively. The luminaire shall be F marked, glow wire tested to 960C and beprovided with an earthing terminal. The luminaire shall be Concord:marlin 2037420.Note : For luminaire with integral emergency kit, the kit shall consists of converterunit, charger circuit and Ni Cd batteries to ensure operation for 3 hours on mainsfailure. The luminaire shall be Concord:marlin 2037421. 3 4. IP: 20Alternative approved :Thorn, Whitecroft, WilaLocation of use : Lobbies in circulation areasLight fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: C1Lamp Type : 1 x TC TEL 26 W + 1 x T 16 - R, Color 830Mounting: RecessedSpecified:Concord:marlin 2038310Detailed specification:Recess mounted luminaire system for use with 1 x 26W TC-TEL + 22 W T16-Rcompact fluorescent lamps. Luminaire shall be in aluminum and steel construction.The central lamps shall be supported in operation by an aluminum vacuummetallized reflector compliant to LG 7. A dished opal polycarbonate diffuser to ensurecompliance to LG 7 shall diffuse the light output of the 22 W lamp. All high frequencydimmable control gear wired for twin switching shall be located internal to theluminaire housing. The cutout diameter shall be limited to 275 mm and the height ofthe luminaire shall be limited to 147 mm. The projection of the diffuser from the line ofthe ceiling shall be limited to 39 mm. The mounting of the luminaire shall be via 4mounting clips. The DLOR and ULOR of the luminaire shall be at least 53% and 4 %respectively. The luminaire shall be F marked, glow wire tested to 960C and beprovided with an earthing terminal. The luminaire shall be Concord:marlin 2038310.Note : For luminaire with integral emergency kit, the kit shall consists of converterunit, charger circuit and Ni Cd batteries to ensure operation for 3 hours on mainsfailure. The luminaire shall be Concord:marlin 2038311. 4 5. IP: 20Alternative approved :Thorn, Whitecroft , WilaLocation of use : VIP DiwaniyaLight fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: DLamp Type : 2 x TC DEL 26 W, Color 830Mounting: Wall and Ceiling surfaceSpecified:Concord:marlin 4065280Detailed specification:Wall or ceiling surface mounted luminaire for use with 2 x TC DEL 26 W compactfluorescent lamps. The luminaire housing shall be a single piece aluminumconstruction finished brushed aluminum. All high frequency control gear along withemergency kit with converter unit, charger and Ni Cd battery for 3 hours operationon mains failure shall be retained internal to the housing. The trim of the luminaireshall ensure a halo backlight on the wall during functioning of the lamp. A UVstabilized satin opal diffuser shall ensure no flashing of the lamp and provide an evenglow of the light output and ensure ingress protection to IP 65. The LOR shall not beless than 51 %. The dimensions of the luminaire shall not exceed 500mm diameter x90 mm height. The luminaire shall be F marked, 960C glow wire tested and beprovided with an earthing terminal. The luminaire shall be Concord:marlin 4065280. 5 6. IP: 65Alternative approved :Hoffmeister, Thorn, ASDLocation of use : StairsLight fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: FLamp Type : 1 x TC TEL 32 W, Color 830Mounting: RecessedSpecified:Concord:marlin 2038676 + 2038997Detailed specification:Recess mounted luminaire for use with 1 x 32 W TC TEL Compact fluorescentlamp. The luminaire housing shall be of die cast aluminum with integral control gearbox of die cast aluminum retaining all high frequency control gear. A highly polishedspecular facetted aluminum reflector shall ensure operation efficiency of 66%, Imaxof approx 420 cd/klm in C0 and approx 460 cd/klm in the C90 planes. The luminaireshall conform to LG 3 Cat 2 and LG 7 lighting standards. The cutout dimension shallnot exceed 204 mm diameter and the luminaire shall be provided with a silvercolored trim of a maximum of 11 mm and thickness less than 7 mm to ensurediscreet appearance on installation. The luminaire shall be mounted via 3 springclips. The connection of the luminaire to the mains shall be carried out via rapidconnect plug and socket system. The height shall not exceed 156 mm. The luminaire 6 7. shall be F rated, glow wire tested to 960C, be ENEC compliant and be provided withearthing terminal. The luminaire shall be Concord LED 150 TE 2038677 + 2038997.Note : For luminaire with emergency kit, the sheet steel remote box kit shall consistof converter unit, charger circuit and Ni Cd batteries to ensure operation for 3 hourson mains failure. The luminaire shall be Concord:marlin 2038677 EM+ 2038997.IP: 20Alternative approved :Erco, WilaLocation of use : CorridorsLight fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: GLamp Type : 2 x TC TEL 32 W, Color 830Mounting: RecessedSpecified:Concord:marlin 2038683 + 2039000Detailed specification:Recess mounted luminaire for use with 2 x 32 W TC TEL Compact fluorescentlamps. The luminaire housing shall be of die cast aluminum with integral control gearbox of die cast aluminum retaining all high frequency control gear. A highly polishedspecular facetted aluminum reflector shall ensure operation efficiency of 66%. Theluminaire shall conform to LEG3 Cat 2 and LG 7 lighting standards. The cutoutdimension shall not exceed 235 mm diameter and the luminaire shall be providedwith a silver colored trim of a maximum of 11 mm and thickness less than 7 mm to 7 8. ensure discreet appearance on installation. The luminaire shall be mounted via 3spring clips. The connection of the luminaire to the mains shall be carried out viarapid connect plug and socket system. The height shall not exceed 156 mm. Theluminaire shall be F rated, glow wire tested to 960C, be ENEC compliant and beprovided with earthing terminal. The luminaire shall be Concord:marlin 2038684 +2039000.Note : For luminaire with emergency kit, the sheet steel remote box kit shall consistof converter unit, charger circuit and Ni Cd batteries to ensure operation for 3 hourson mains failure. The luminaire shall be Concord:marlin 2038684 EM + 2039000.IP: 20Alternative approved :Erco, Hoffmeister, WilaLocation of use : CorridorsLight fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: HLamp Type : 2 x TC TEL 26 W, Color 830Mounting: RecessedSpecified:Concord:marlin 2038681 + 2038991Detailed specification: 8 9. Recess mounted luminaire for use with 2 x 26 W TC TEL Compact fluorescentlamps. The luminaire housing shall be of die cast aluminum with integral control gearbox of die cast aluminum retaining all high frequency control gear. A highly polishedspecular facetted aluminum reflector shall ensure operation efficiency of 61%. Theluminaire shall conform to LG 7 lighting standards. The cutout dimension shall notexceed 204 mm diameter and the luminaire shall be provided with a silver coloredtrim of a maximum of 11 mm and thickness less than 7 mm to ensure discreetappearance on installation. A clear glass diffuser shall be provided to ingress protectthe luminaire. The luminaire shall be mounted via 3 spring clips. The connection ofthe luminaire to the mains shall be carried out via rapid connect plug and socketsystem. The height shall not exceed 156 mm. The luminaire shall be F rated, glowwire tested to 960C, be ENEC compliant and be provided with earthing terminal.The luminaire shall be Concord:marlin 2038682 + 2038991.Note : For luminaire with emergency kit, the sheet steel remote box kit shall consistof converter unit, charger circuit and Ni Cd batteries to ensure operation for 3 hourson mains failure. The luminaire shall be Concord:marlin 2038682 EM + 2038991.IP: 44Alternative approved :Wila, LumianceLocation of use : ToiletsLight fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: JLamp Type : 2 x TC TEL 18 W, Color 830Mounting: Recessed 9 10. Specified:Concord:marlin 2038678 + 2039014Detailed specification:Recess mounted luminaire for use with 2 x 18 W TC TEL Compact fluorescentlamps. The luminaire housing shall be of die cast aluminum with integral control gearbox of die cast aluminum retaining all high frequency control gear. A highly polishedspecular facetted aluminum reflector shall ensure operation efficiency of 62%. Theluminaire shall conform to LG 7 lighting standards. The cutout dimension shall notexceed 204 mm diameter and the luminaire shall be provided with a silver coloredtrim of a maximum of 11 mm and thickness less than 7 mm to ensure discreetappearance on installation. A clear vandal resistant polycarbonate diffuser shall beprovided to ingress protect the luminaire. The luminaire shall be mounted via 3 springclips. The connection of the luminaire to the mains shall be carried out via rapidconnect plug and socket system. The height shall not exceed 156 mm. The luminaireshall be F rated, glow wire tested to 960C, be ENEC compliant and be provided withearthing terminal. The luminaire shall be Concord:marlin 2038680 + 2039014.Note : For luminaire with emergency kit, the sheet steel remote box kit shall consistof converter unit, charger circuit and Ni Cd batteries to ensure operation for 3 hourson mains failure. The luminaire shall be Concord:marlin 2038680 EM + 2039014.IP: 54Alternative approved :Wila, LumianceLocation of use : Toilet cubiclesLight fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: KLamp Type : 1 x T5 35 W, Color 830Mounting: Recessed 10 11. Specified:Norlight SL I 135 OPDetailed specification:Recess mounted luminaire for use with 1 x 35 W T5 Linear fluorescent lamps. Theluminaire housing shall be of extruded aluminum, surface treated and painted withpolymerized paints to finish silver grey. An inner reflector shall serve to enhance thelight distribution and to mount all the all high frequency control gear. A UV stabilizedpolycarbonate diffuser 1.5 mm thick with snap on arrangement shall be used todiffuse the light and to ingress protect the fixture. All internal wiring shall be executedwith 0.75 mm heat resistant H05V2-U cable. The luminaire shall comply with EN60598-1 and conform to Electrical class I. The width of the luminaire lip to lip shallbe limited to 75 mm and the lip thickness shall be limited to 1.6 mm to make themounting discrete. Luminaire depth shall not exceed 93 mm. The luminaire shall beNorlight SL I 135 OP.Note : For luminaire with emergency kit, the sheet steel remote box kit shall consistof converter unit, charger circuit and Ni Cd batteries to ensure operation for 3 hourson mains failure.IP:40Alternative approved : Wila, ZumtobelLocation of use :MirrorsLight fittings specifications :Stadium and Sports Facilities at Shuwaikh CampusType:LLamp Type :3 x T5 28 W, Color 840Mounting:Suspended11 12. Specified:Norlight T14BD202CHDetailed specification:Suspension mounted luminaire for use with 3 x 28 W T5 Linear fluorescent lamps.The luminaire housing shall in two piece construction. The four side panels shall beof solid extruded aluminum, surface finished and painted with polymerized paints toRAL 9006 half luster aluminum. The central optical compartment and side panelsshall be of brake formed sheet steel and finished RAL 9006. The symmetricalparabolic optical unit shall comprise of parabolic longitudinal elements and closedparabolic louvers with triple parabolic feature. The optical system shall be made ofvery pure aluminum, PVD treated mirror bright oxidized to 2m. The optical systemshall ensure average direct luminance lesser than 400 cd/m2, both lengthwise andcrosswise, for observation angles greater than 65 from the vertical. The luminaireshall have stainless steel fasteners and No-fall retention systems for easymaintenance. Translucent glass refractor shall ensure side emissions. A diffuser ofshock resistant non ageing high transparency polycarbonate shall ensure diffusedindirect light distribution. All high frequency control gear complete with a disconnectfuse of dia 5 x 20 m, shall be included in the internal wiring executed with 0.75 mmheat resistant H05V2-U cable. The luminaire dimensions shall be 366mm x 1260mmx 54 mm to comply with mounting restrictions and architectural requirements. Theluminaire shall be Norlight T14BD202CH.Note : For luminaire with emergency kit, the sheet steel remote box kit shall consistof converter unit, charger circuit and Ni Cd batteries to ensure operation for 3 hourson mains failure.IP: 20Alternative approved :Wila, ZumtobelLocation of use : Circulation areasLight fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: MLamp Type : T16 R 1 x 40 W + 1 x TC-TEL 26 W, Color 840Mounting: RecessedSpecified:Concord:marlin 4064670 12 13. Detailed specification:Recess mounted luminaire for use with 1 x T5 40 W and 1 x 26 W TC TE lamps.Luminaire housing in sheet steel, with ambient reflector in aluminum powder coatedwhite RAL 9016 and central down light reflector in anodized aluminum. The diffusershall be of opal polycarbonate smooth finished. All high frequency control gear shallbe retained within the housing prewired upto the connector block. At least 3 retainingclips shall be provided to keep the circular lamp in position. The DLOR and ULORshall be at least 54% and 7% respectively and conform to CIBSE Lighting Guide LG7 standards of lighting. The diffuser shall project fro the line of the ceiling bymaximum of 54 mm. The dimensions of the luminaire shall not exceed 590 mmdiameter x 125 mm height. The luminaire shall be F marked, be provided with anearthing terminal, glow wire tested to 960C and be ENEC compliant. The luminaireshall be Concord:marlin 4064670.Note : For luminaire with emergency kit, the sheet steel remote box kit shall consistof converter unit, charger circuit and Ni Cd batteries to ensure operation for 3 hourson mains failure. The luminaire shall be Concord:marlin 4065257.IP: 20Alternative approved :Wila, WhitecroftLocation of use : Office rooms, Examination roomsLight fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: NLamp Type : 1 x TC TEL 18 W, Color 830Mounting: RecessedSpecified:Concord:marlin 2037234 + 2017414 13 14. Detailed specification:Recess mounted luminaire for use with 1 x TC TEL 18 W lamp. Luminaire housingin polyethirimide, and with integral control gear housing to hold high frequencycontrol gear. The luminaire shall be provided with a reflector in spun aluminum. Thecutout diameter shall not exceed 100 mm to keep in line with the architecturallimitations and requirements. The height of the luminaire shall not exceed 135 mm. Asatin chrome finished bezel ring shall finish the front opening of the fixture. TheDLOR of the luminaire shall not be lower than 60%. The luminaire shall be F ratedand be provided with an earthing terminal. The luminaire shall be Concord:marlin2037235 + 2017414.Note : For luminaire with emergency kit, the sheet steel remote box kit shall consistof converter unit, charger circuit and Ni Cd batteries to ensure operation for 3 hourson mains failure. The luminaire shall be Concord:marlin 2037235 EM + 2017414.IP: 20Alternative approved :Wila, ErcoLocation of use : Architectural decorative featuresLight fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: PLamp Type : 1 x 12 V 50 W MR 16 38 beamMounting: Recessed 14 15. Specified:Linolite 2426032Detailed specification:Recess mounted luminaire for use with 1 x 12 V 50 W MR 16 lamp. Luminairehousing in die cast aluminum and in chrome finish. The front of the luminaire shall bein clear glass with a central flat disc. The luminaire shall be provided with anelectronic transformer. The cutout diameter shall be limited to 90mm. The luminaireshall be Linolite 2426032.Note : For luminaire with emergency kit, the sheet steel remote box kit shall consistof converter unit, charger circuit and Ni Cd batteries to ensure operation for 3 hourson mains failure. The kit shall be placed over the false ceiling via the same cutoutopening for the luminaire and shall not require a separate access panel.IP:65Alternative approved : Zumtobel, HoffmeisterLocation of use :Shower cubiclesLight fittings specifications :Stadium and Sports Facilities at Shuwaikh CampusType:Q1Lamp Type :1 x 12 V 35 W MR 16Mounting:Recessed 15 16. Specified:Linolite 2425886Detailed specification:Recess mounted luminaire for use with 1 x 12 V 35 W MR 16 lamp. Luminairehousing in die cast aluminum and in chrome finish. The front of the luminaire shall bein clear glass with a central flat disc. The luminaire shall be provided with anelectronic transformer. The cutout diameter shall be limited to 90mm. The luminaireshall be Linolite 2425886.Note : For luminaire with emergency kit, the sheet steel remote box kit shall consistof converter unit, charger circuit and Ni Cd batteries to ensure operation for 3 hourson mains failure.IP:65Alternative approved : Hoffmeister, ErcoLocation of use :SaunaLight fittings specifications :Stadium and Sports Facilities at Shuwaikh CampusType:RLamp Type :1 x T5 54 W, Color 830Mounting:SuspendedSpecified:Norlight T41KK012AI + MEC0682AI + MEC0706AI 16 17. Detailed specification:Suspension mounted luminaire for use with 1 x T5 54 W linear fluorescent lamp. Thehousing shall be composed of a support beam made from 2 mm thick galvanizedbrake-formed steel plate surface-treated and painted half luster aluminum RAL 9006using polymerized powder paints, to hold the lighting components, inclusive of acomplete with a sealed light fitting with lamp protection tube, 38mm dia. no-fallsealed nipple, mirror-finish reflector and light mesh screen. All hardware shall be instainless steel. A plain mirror-finish symmetrical reflector with macro-mirror profile,made from mirror-finish high-bright oxidized (2 m) aluminum with 99.85% Al contentshall be provided. A solid light mesh screen made from 1mm thick aluminum pre-painted half luster aluminum RAL 9006, drilled in size 8x8 mm with pitch 10 mm anda hollow/solid ratio equal to 64%. It shall be secured by means of AISI 303 stainlesssteel M4 hex-head lock pins. No-fall chains made of electrically welded galvanizedsteel rings, with terminal hooks. Optimized light flux distribution and reduction ofunwanted effects deriving from direct glare luminance. All high frequency control gearshall be held internal to the housing. The luminaire shall be provided with connectionand alignment kits to achieve linear light lines and end cover kits to be used at eitherend of the light lines. The luminaire shall be Norlight T41KK012AI + MEC0682AI +MEC0706AI.Note : For luminaire with emergency kit, the sheet steel remote box kit shall consistof converter unit, charger circuit and Ni Cd batteries to ensure operation for 3 hourson mains failure. The kit shall be located suitably internal to the housing.IP: 65Alternative approved :Norka, HoffmeisterLocation of use : SaunaLight fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: SLamp Type : 1 x HIT CE 150 W, Color 830Mounting: Suspended 17 18. Specified:Concord:marlin 4065658 + Dcor glassDetailed specification:Suspension mounted luminaire for use with 1 x HIT CE 150 W metal halide lamp.The housing shall in die cast aluminum finished silver, and house the control gear.Three die cast fins shall grasp the spun aluminum reflector. The 3 wire suspensionsystem shall be adjustable site dependable. The luminaire shall also be provided witha safety glass. A decorative bottom glass shall be included in addition to the safetyglass. The DLOR of the luminaire shall be not less than 72%. The luminaire shall beConcord:marlin 4065658 + Dcor glass.IP: 44Alternative approved :Zumtobel, Regent, CromptonLocation of use : Gym, TrainingLight fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: TLamp Type : 2 x TC TEL 42 W, Color 830Mounting: Recessed 18 19. Specified:Concord:marlin 2038685 + 2039000Detailed specification:Recess mounted luminaire for use with 2 x 42 W TC TEL Compact fluorescentlamps. The luminaire housing shall be of die cast aluminum with integral control gearbox of die cast aluminum retaining all high frequency control gear. A highly polishedspecular facetted aluminum reflector shall ensure operation efficiency of 74%. Theluminaire shall conform to LG 7 lighting standards. The cutout dimension shall notexceed 235 mm diameter and the luminaire shall be provided with a silver coloredtrim of a maximum of 11 mm and thickness less than 7 mm to ensure discreetappearance on installation. The luminaire shall be mounted via 3 spring clips. Theconnection of the luminaire to the mains shall be carried out via rapid connect plugand socket system. The height shall not exceed 156 mm. The luminaire shall be Frated, glow wire tested to 960C, be ENEC compliant and be provided with earthingterminal. The luminaire shall be Concord:marlin 2038686 + 2039000.Note : For luminaire with emergency kit, the sheet steel remote box kit shall consistof converter unit, charger circuit and Ni Cd batteries to ensure operation for 3 hourson mains failure. The luminaire shall be Concord:marlin 2038686 EM + 2039000.IP: 20Alternative approved :Wila, HoffmeisterLocation of use : CorridorsLight fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: U 19 20. Lamp Type : 1 x TC TEL 32 W, Color 830Mounting: RecessedSpecified:Concord:marlin 2028027 + 2028038Detailed specification:Recess mounted luminaire for use with 1 x 32 W TC TEL Compact fluorescentlamps. The luminaire housing shall be of die cast aluminum with integralpolycarbonate control gear box retaining all high frequency control gear. A highlypolished specular spun aluminum reflector shall ensure operation efficiency of 73%.The cutout dimension shall not exceed 178 mm diameter and the luminaire shall beprovided with a silver colored trim of a maximum thickness less than 7 mm to ensurediscreet appearance on installation. The luminaire shall be mounted via 3 springclips. The height shall not exceed 100 mm. The luminaire shall be F rated, glow wiretested to 960C, be ENEC compliant and be provided with earthing terminal. Theluminaire shall be Concord:marlin 2028028 + 2028038.Note : For luminaire with emergency kit, the sheet steel remote box kit shall consistof converter unit, charger circuit and Ni Cd batteries to ensure operation for 3 hourson mains failure. The luminaire shall be Concord:marlin 2028028 EM + 2028028.IP: 20Alternative approved :Zumtobel, WilaLocation of use : Prayer roomsLight fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: V 20 21. Lamp Type : 2 x T5 54 W, Color 830Mounting: SurfaceSpecified:Norlight T81HD033EUDetailed specification:Surface mounted luminaire for use with 2 x 54 W TC TEL Compact fluorescentlamps. Housing made from brake-formed electrically welded steel plate in thickness0.7 mm approx., surface-treated and painted half-lustre white using polymerizedpowder paints. A PMMA Planirex screen composed of a 3 mm thick methacrylateplate with prism-textured inside and smooth outside shall be provide to ingressprotect the fixture. The PMMA screen shall be set in a frame of extruded aluminumanodized natural. The diffuser shall be secured by means of no-loss nickel steel pinsto be rotated by 90. A set of No-fall tie-rods shall ensure safety during routinemaintenance. This shall be complete with pin seat covers, perfectly co-planar to theframe, made from oxidized anodized extruded aluminum. All high frequency controlgear shall be retained internal to the housing and e wired with 2.5 mm2 LTN terminalblock, disconnect fuse holder complete with fuse, dia. 5x20, 0.75 mm2 H05V2-Uheat-resistant stiff cable. The luminaire shall be Electric protection Class I compliant,comply with harmonized standards for luminaires CEI EN 60598-1. The luminaireshall be Norlight T81HD033EU.Note : For luminaire with emergency kit, the sheet steel remote box kit shall consistof converter unit, charger circuit and Ni Cd batteries to ensure operation for 3 hourson mains failure. The luminaire shall be Norlight 3ET81HD033EU.IP: 54Alternative approved :Zumtobel, LudwigLocation of use : Store roomsLight fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: V1 21 22. Lamp Type :2 x 36 W T8, Color 830Mounting:SurfaceSpecified:Cortem EVFD 236 EBDetailed specification:Surface mounted luminaire for use with 2 x 36 W T8 Linear fluorescent lamps.Housing made of aluminum alloy and diffuser of a temperature - resistant temperedglass tube, sealed on two aluminum sockets and of two heads supplied with lampholders. The luminaire shall be compliant to CENELEC standards EN 50014: 1997 +A1A2, EN 50018: 2000, EN 50281-1-1: 1999 and European Directive 94/9/EC:1994. Execution 0722: II 2GD EEx d IIC T5/T6 IP 66. All high frequency control gearshall be retained internal to the fixture. The luminaire shall be Cortem EVFD 236 EB.IP:66Alternative approved : CEAG, CromptonLocation of use :Explosion proof areasLight fittings specifications :Stadium and Sports Facilities at Shuwaikh CampusType:W22 23. Lamp Type :1 x HIT - TD 70 W, Color 830Mounting:RecessedSpecified:Norlight T86MK127CHDetailed specification:Recess mounted luminaire for use with 1 x 70 W HIT TD Metal halide lamp.Housing made from brake-formed electrically welded steel plate in thickness 0.7 mmapprox and a steel frame 2 mm thick TIG welded, surface-treated and painted half-lustre aluminum RAL 9006, using polymerized powder paints. The base shall befitted and firmly retained into a sealed case made of brake-formed electrically weldedsteel plate in thickness 0.7 mm approx. The sealed case shall be secured to the falseceiling by means of a special framework. A symmetrical hammered reflector withmacro-mirror profile, made from mirror-finish high-bright oxidized aluminumhammered with concave embossing in thickness 0.7 mm, shall ensure widedistribution. A CV screen composed of a 0.8 mm thick steel plate contouring frameassembled, TIG welded and painted using polymerized powder paints, and a 4 mmthick glass pane with ground edges, smooth outside and dulled translucent inside,shall ingress protect the fixture. The glass diffuser shall be secured by means of no-loss screws. All control gear shall be retained internal to a separate sheet steel gearbox. The luminaire shall be Electric protection Class I compliant, comply withharmonized standards for luminaires CEI EN 60598-1. The luminaire shall beNorlight T86MK128CH.IP:54Alternative approved : Bega, WeefLocation of use :Canopy Lvl 4.5Light fittings specifications :Stadium and Sports Facilities at Shuwaikh CampusType:W323 24. Lamp Type :1 x HIT - TD 70 W, Color 830Mounting:Surface MountedSpecified:Norlight T86MK127CHDetailed specification:Recess mounted luminaire for use with 1 x 70 W HIT TD Metal halide lamp.Housing made from brake-formed electrically welded steel plate in thickness 0.7 mmapprox and a steel frame 2 mm thick TIG welded, surface-treated and painted half-lustre aluminum RAL 9006, using polymerized powder paints. The base shall befitted and firmly retained into a sealed case made of brake-formed electrically weldedsteel plate in thickness 0.7 mm approx. The sealed case shall be secured to the falseceiling by means of a special framework. A symmetrical hammered reflector withmacro-mirror profile, made from mirror-finish high-bright oxidized aluminumhammered with concave embossing in thickness 0.7 mm, shall ensure widedistribution. A CV screen composed of a 0.8 mm thick steel plate contouring frameassembled, TIG welded and painted using polymerized powder paints, and a 4 mmthick glass pane with ground edges, smooth outside and dulled translucent inside,shall ingress protect the fixture. The glass diffuser shall be secured by means of no-loss screws. All control gear shall be retained internal to a separate sheet steel gearbox. The luminaire shall be Electric protection Class I compliant, comply withharmonized standards for luminaires CEI EN 60598-1. The luminaire shall beNorlight T86MK128CH.IP:54Alternative approved : Bega, WeefLocation of use :Canopy Lvl 4.5Light fittings specifications :Stadium and Sports Facilities at Shuwaikh CampusType:Y24 25. Lamp Type : 1 x HIT CE 70 W, Color 830Mounting: IngroundSpecified:SBP 05209896 + 14075320Detailed specification:Inground recess mounted luminaire for use with 1 x HIT CE 70 W Metal halide G12lamp. The luminaire housing shall be in die cast aluminum to withstand load andimpact. A molded borosilicate toughened glass lens shall be used to ensuredispersion of light. The luminaire shall be supplied complete with stainless steelfixings and ground mounting kit. The technopolymer body and outer recessingenclosure, with good high and low temperature resistance shall protect the housing.Anti-ageing silicon rubber gaskets shall ensure ingress protection. M20x1.5mm cablegland for 7- 12mm cables shall be provided. A 2x2.5mm2 switch splitter, toautomatically interrupt the electrical supply when cover is opened shall ensure safetyduring routine maintenance. All external hardware shall be in stainless steel. A semicircular internal aluminum accessory shall ensure 180 distribution of light. Theprojection of the luminaire above ground shall be limited to 70 mm to ensure safety ofpersons using the area where the fixtures are installed. The luminaire shall be Frated, IK 08, 5J impact resistant and be CE compliant. The luminaire shall be SBP05209896 + 14075320.IP: 67Alternative approved :Bega, WeefLocation of use : BalconyLight fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: Z 25 26. Lamp Type : 0.1 W LEDS, 80 mm spacingMounting: RecessedSpecified:Tokistar MCW 80 - WWDetailed specification:Continous LED strip lighting system consisting of 0.1 W / 8V / 0.25mA LEDs spaced80 mm apart c-to-c, and retained in a Polycarbonate extrusion. The base of theextruded channel shall be 13mm wide with the overall height of the linear systembeing limited to 13mm. The LEDs shall be provided with a phosphor coated lens toensure all round viewing and thereby a very even and soft glow of light. The LEDSshall provide a warm white light output. The fixture shall be located beneath the noseof the step. The edges around the fixture shall be filled with silicon glue afterinstallation to prevent water seepage. Sufficient number of control gears, LDR 80 each of 40 W rating and 5.0A maximum output current shall ensure 240 V AC to 8 VDC supply to the LEDs. The dimensions of the IP 65 protected transformer, suitablylocated to meet site conditions, shall be limited to 50mm x 75 mm x 248 mm. Alllengths shall be factory cut standard lengths to ensure proper matching. The systemshall be Tokistar MCW 80 W.IP: 65Alternative approved :Roberts, TrykaLocation of use : StepsLight fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: AA 26 27. Lamp Type :2 sets of 2 x 21 W T5 lamps, Color 830Mounting:SuspendedSpecified:Supermodular 2x93105220 + 93100050 connector +2x93100150 suspension kit + 93100151 flexible powerconnection box + 2x93100181 end plateDetailed specification:Continuous suspended light line profile of extruded aluminum, in matt anodizedfinish. The light line shall consist of 2 units each of 2 x 21 W T 5 lamps, complete withall high frequency control gear. The 2 units shall be linked via a blank profile 120 mmlong. Each lighting unit shall provide for upward and downward light distribution of notlesser than 50% and 23% respectively. The luminaire width shall not be lesser than300 mm with the length of the complete light line being 1960 mm. The light line endsshall be closed with factory cut end plates. The system shall be complete with allrequisite accessories not limited by the units identified here, to provide a completesystem on site. The suspension length shall be as per site conditions to meet witharchitects approval. The system shall be Supermodular 2x93105220 + 93100050connector + 2x93100150 suspension kit + 93100151 flexible power connectionbox + 2x93100181 end plate.Note : For luminaire with emergency kit, the kit consisting of converter unit, chargercircuit and Ni Cd batteries to ensure operation for 3 hours on mains failure shall bemounted internal to the fixture above to power one of the for lamps.IP:20Alternative approved : Sylvania, Zumtobel, WilaLocation of use :VIP circulation areasLight fittings specifications :Stadium and Sports Facilities at Shuwaikh CampusType:AB27 28. Lamp Type : 0.24 W LEDS, 30 mm spacingMounting: Surface, Cove lightSpecified:Tokistar TLP - 30 P4WWDetailed specification:Continous LED strip lighting system consisting of 0.24 W / 8V / 30mA LEDs spaced30 mm apart c-to-c, and set in flexible PVC conductors. The base of the PVCconductors shall be limited to 11 mm, and the height of the cove light shall be limitedto 19 mm. The 100 viewing angle of the LED shall ensure pure and smooth wash oflight. The Warm white LEDS shall conform to 3000 K color temperature. The flexibletapelight system shall be mounted onto the cove by double sided adhesive tape.Sufficient number of control gears LDR8 40 each of 40 W rating and 5.0Amaximum output current shall ensure 240 V AC to 8 V DC supply to the LEDs. Eachtransformer shall address a maximum of 166 LEDs. The dimensions of the IP 65protected transformer shall be limited to 50mm x 75 mm x 248 mm. All lengths shallbe cut in situ to ensure proper matching. The system shall be Tokistar TLP - 30 P4WW.IP: 20Alternative approved :Roberts, TrykaLocation of use : Coves in VIP areasLight fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: AC 28 29. Lamp Type : 4 x T5 14 W Linear fluorescent, Color 830Mounting: RecessedSpecified:Norlight T33 MD047EUDetailed specification:Ceiling recess mounted fluorescent luminaire for 4 x 14 W T5 linear fluorescentlamps. The luminaire housing shall be made of brake-formed electrically welded steelplate in thickness 0.7 mm approx., surface-treated and painted half-luster white withpolymerized powder paints. A VR Planirex screen composed of a 3 mm thicktransparent toughened glass pane set in a frame of extruded aluminum anodizednatural and secured by means of no-loss nickel steel pins rotatable by 90. A No-fallchain system made of galvanized electrically welded steel rings with terminal hooksand with pin seat covers, perfectly co-planar to the frame, made from oxidizedanodized extruded aluminum and fitted with no-fall tie-rods that guarantee safetyduring routine maintenance. The luminaire shall also be equipped with an SSMsymmetrical reflector with macro-mirror profile, made from mirror-finish high-brightoxidized (2 m) aluminum with 99.85% Al content to ensure distribution. All highfrequency control gear shall be retained internal to the housing and be wired with 2.5mm2 LTN terminal block, disconnect fuse holder complete with fuse of dia. 5x20. Allwiring shall be 0.75 mm2 H05V2-U heat-resistant stiff cables. The luminaire shallconform to Electric protection Class I. Complying with harmonized standards forluminaires CEI EN 60598-1 (general provisions and testing) and CEI EN 60598-2-22(luminaires with emergency). The luminaire shall be Norlight T33 MD047EU.Note : For luminaire with emergency kit, the kit shall consist of converter unit, chargercircuit and Ni Cd batteries to ensure operation for 3 hours on mains failure, allretained internal to the fixture. The luminaire shall be Norlight 3E T33 MD047EU.IP: 65Alternative approved :Crompton, ZumtobelLocation of use : Kitchens, PantriesLight fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: AD 29 30. Lamp Type : 2 x TC TEL 32 W compact fluorescent,Color 830Mounting: RecessedSpecified:Concord:marlin 2038752 + 2039000Detailed specification:Recess mounted luminaire for use with 2 x 32 W TC TEL Compact fluorescentlamps. The luminaire housing shall be of die cast aluminum with integral control gearbox of die cast aluminum retaining all high frequency control gear. A highly polishedspecular smooth aluminum reflector shall ensure operation efficiency of 58% andensure even wash top to bottom. The luminaire shall conform to LG 7 lightingstandards. The cutout dimension shall not exceed 235 mm diameter and theluminaire shall be provided with a silver colored trim of a maximum of 11 mm andthickness less than 7 mm to ensure discreet appearance on installation. Theluminaire shall be mounted via 3 spring clips. The connection of the luminaire to themains shall be carried out via rapid connect plug and socket system. The height shallnot exceed 156 mm. The luminaire shall be F rated, glow wire tested to 960C, beENEC compliant and be provided with earthing terminal. The luminaire shall beConcord:marlin 2038752 + 2039000.Note : For luminaire with emergency kit, the sheet steel remote box kit shall consistof converter unit, charger circuit and Ni Cd batteries to ensure operation for 3 hourson mains failure. The luminaire shall be Concord:marlin 2038752 EM + 2039000.IP: 20Alternative approved :Erco, WilaLocation of use : Wall washersLight fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: AF 30 31. Lamp Type : 1 x TC TEL 32 W, Color 830Mounting: RecessedSpecified:Concord:marlin 2028027 + 2028600Detailed specification:Recess mounted luminaire for use with 1 x 32 W TC TEL Compact fluorescentlamps. The luminaire housing shall be of die cast aluminum with integralpolycarbonate control gear box retaining all high frequency control gear. A highlypolished specular spun aluminum reflector shall ensure operation efficiency of 73%.The cutout dimension shall not exceed 178 mm diameter and the luminaire shall beprovided with a clear glass diffuser set in a silver colored trim of a maximumthickness less than 7 mm to ensure discreet appearance on installation. Theluminaire shall be mounted via 3 spring clips. The height shall not exceed 100 mm.The luminaire shall be F rated, glow wire tested to 960C, be ENEC compliant andbe provided with earthing terminal. The luminaire shall be Concord:marlin 2028027+ 2028600.Note : For luminaire with emergency kit, the sheet steel remote box kit shall consistof converter unit, charger circuit and Ni Cd batteries to ensure operation for 3 hourson mains failure. The luminaire shall be Concord:marlin 2028028 EM + 2028600.IP: 44Alternative approved :Hoffmeister, WilaLocation of use : ToiletsLight fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: AG 31 32. Lamp Type : 1 x HIS - TD 70 W, Color 840Mounting: SurfaceSpecified:Sylvania 0053145Detailed specification:Surface mounted luminaire for use with 1 x 70 W HIS TD double ended Metalhalide lamp. The luminaire housing shall be of die cast aluminum with all control gearmounted integral to the housing. A highly polished specular anodized aluminumasymmetric reflector shall ensure high operation efficiency and forward throw lightdistribution. The luminaire dimension shall not exceed 231 mm height and projectionfrom wall of 233 mm. The luminaire shall be finished dark grey polyester powdercoat. The front of the luminaire shall be protected by a toughened glass pane toingress protect the luminaire. All external hardware shall be in Stainless steel. Theluminaire shall be F rated, be ENEC compliant and be provided with earthingterminal. The luminaire shall be Sylvania 0053145.IP: 65Alternative approved :Simes, WeefLocation of use : External to substation.Light fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: AH 32 33. Lamp Type : 1 x HIT - DE 250 W, Color 840Mounting: RecessSpecified:Concord:marlin 2038645 + 2038997Detailed specification:Recess mounted luminaire for use with 1 x 250 W HIT DE double ended Metalhalide lamp. The luminaire housing shall be of die cast aluminum with all control gearmounted separately in a non integral to the housing. A textured spun aluminumreflector shall ensure a beam angle of 63 x 103 and DLOR of 67%. An integralborosilicate safety glass shall ingress protect the luminaire. Relamping shall bepossible from below. The trim shall be a silver bezel, 7 mm thick to be discreet. Theluminaire cutout dimensions shall not exceed 204mm. The dimension shall notexceed 240 mm height. It shall be provided with a 3 point mounting system to ensurefirm mounting. All external hardware shall be in Stainless steel. The luminaire shallbe F rated, glow wire tested to 960C, and be provided with earthing terminal. Theluminaire shall be Concord:marlin 2038645 + 2038997.IP: 44Alternative approved :Erco, BegaLocation of use : VIP entrance.Light fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: AJ 33 34. Lamp Type : LED 1 WMounting: Wall recessedSpecified : Tryka TH M1 - B + TC CD36Detailed specification:Luminaire for use with 1 LED Blue color. The luminaire housing shall be of stainlesssteel. Modulation unit: This electronic control unit shall be used for the operation ofthe LED lighting modules. Upto 36 M1 modules shall be operable on a singlemodulation unit. The modulation unit shall be optimized for prolonged life of LEDs. Itshall provide for 3 individually addressable outputs via DMX, Smooth dimming control0 100%, Thermal feedback protection. The unit shall be short and open circuitprotected and meet lighting approbation requirements (CE). It shall have a ruggedconstruction and be suitably remote mounted with reference to site conditions. Theconfiguration of lighting module, modulation units and the controller units shall be asper manufacturers recommendations. The system shall be Tryka TH M1 - B + TC CD36.IP: 67Alternative approved :Wever & Ducre, WeefLocation of use : VIP EntranceLight fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: AK 34 35. Lamp Type : 1 x 400 W HQI BT Metal halideMounting: Wall mountedSpecified : SBP 05214096 + 14077696Detailed specification:Wall mounted flood lighting fixture for use with 1 x 400 W HQI BT metal halidelamp. The luminaire housing and canopy shall be of die cast aluminum finished RAL7039. It shall retain a high purity aluminum reflector anodized and polished andensuring zero upward light pollution. The reflector shall ensure Imax of about440cd/klm at 18 and achieve a beam spread of at least 136 across the lamp axisand about 45 across the lap axis. A toughened safety glass shall ingress protect thefixture to IP 65 with a silicon anti aging gasket. All external screws shall be instainless steel. The luminaire shall be provided with polyamide M25 cable glands forcable entry. All electrical components shall be housing on a techno polymer gear trayeasily accessible from the top opening cover of the luminaire. The cover shall openupto 170 for easy access. The lamp holder shall have flexibility to be located at 3different positions to vary the light distribution parameters. The luminaire shallconform to IK08 8J, be under 13 kilos in weight to ensure easy handling and have awindage area of under 0.24 m. The system shall be SBP 05214096 + 14077696.IP: 65Alternative approved :Weef, BegaLocation of use : Columns around stadiumLight fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: AL 35 36. Lamp Type :9 nos Blue LEDs 24V 1.5 WMounting:In groundSpecified : SBP Lyn4 AL 06001404Detailed specification:In ground mounted orientation luminaire for use with 9 nos Blue LEDs 24 V 1.5 W.The luminaire shall be in die cast aluminum construction with a corrosion resistant360 hedgehog in ground outer cap in die cast aluminum with a low copper content,chromate treated and painted in metallized aluminum grey RAL 9006. A transparentUV stabilized polycarbonate diffuser shall enhance visibility level. The diffuser shallbe set in a silicon gasket for ingress protection to IP68. The front of the luminaireshall be in stainless steel finish. A techno polymer recessed outer case and body,resistant to corrosion due to chemical polluted substances, low temperatures andhydrolysis resistant shall ensure proper operation of the unit. All external hardwareshall be in stainless steel. The fitting shall be complete, with two IP68 anti-tearingcable glands and one grommet for single or in series connection installation. Everysix fixtures shall be powered via a 10 W electronic transformer set within a groundrecessed IP 67 box A0221/10 - in techno polymer, complete with PG13.5 cableentry glands. The luminaire diameter shall not exceed 108 mm be IK09, 12J. Theluminaire shall be SBP Lyn4 T 06001404.IP:6836 37. Alternative approved : Weef, Color KineticsLocation of use :VIP EntranceLight fittings specifications :Stadium and Sports Facilities at Shuwaikh CampusType:AMLamp Type :2 x 18 W,CFL-whiteMounting:RecessedSpecified : WILADetailed specification:Recess mounted luminaire for use with 2 X 18 W compact fluorescent lamp in line,and still ensure uniform brightness. The luminaire dimension shall be limited to 210mm dia with to conform to the architectural requirements of the installation. Theluminaire shall be EN 60598-1 compliant, and be Electrical Class I. The luminaireshall be wila C2652-33Note: For luminaire with emergency kit, the sheet steel remote box kit shall consist ofconverter unit, charger circuit and Ni Cd batteries to ensure operation for 3 hourson mains failure.IP:23Alternative approved : Zumtobel, RSLLocation of use :Spectator concourse37 38. Light fittings specifications :Stadium and Sports Facilities at Shuwaikh CampusType:AM1Lamp Type :1 x 42 W,CFL-whiteMounting:Surface MountedSpecified : WILADetailed specification:Recess mounted luminaire for use with 1 X 42 W compact fluorescent lamp in line,and still ensure uniform brightness. The luminaire dimension shall be limited to 255mm dia with to conform to the architectural requirements of the installation. Theluminaire shall be EN 60598-1 compliant, and be Electrical Class I. The luminaireshall be wila C2694-33Note: For luminaire with emergency kit, the sheet steel remote box kit shall consist ofconverter unit, charger circuit and Ni Cd batteries to ensure operation for 3 hourson mains failure.IP:23Alternative approved : Zumtobel, RSLLocation of use :Spectator concourse38 39. Light fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: ANLamp Type : 3 x TC D 26 W, Color 830Mounting: SuspendedSpecified:Concord:marlin 4065659 + Dcor glassDetailed specification:Suspension mounted luminaire for use with 3 x TC D 26 W compact fluorescentlamps. The housing shall in die cast aluminum finished silver, and house the controlgear. Three die cast fins shall grasp the spun aluminum reflector. The 3 wiresuspension system shall be adjustable site dependable. The luminaire shall also beprovided with a safety glass. A decorative bottom glass shall be included in additionto the safety glass. The DLOR of the luminaire shall be not less than 72%. Theluminaire shall be Concord:marlin 4065659 + Dcor glassIP: 20Alternative approved :Martini, Thorn UK 39 40. Location of use : Spectator concourseLight fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: APLamp Type : 1 x TC TEL 26 W, Color 830Mounting: RecessedSpecified:Concord:marlin 2030718 + 2028037Detailed specification:Recess mounted luminaire for use with 1 x 26 W TC TEL Compact fluorescentlamps. The luminaire housing shall be of die cast aluminum with integral control gearbox of polycarbonate retaining all high frequency dimmable control gear. A highlypolished specular facetted aluminum reflector shall ensure operation efficiency of66%. The luminaire shall conform to LG 7 lighting standards. The cutout dimensionshall not exceed 137 mm diameter and the luminaire shall be provided with a silvercolored trim of a maximum of 11 mm and thickness less than 7 mm to ensurediscreet appearance on installation. The luminaire shall be mounted via 3 springclips. The height shall not exceed 98 mm. The luminaire shall be F rated, glow wiretested to 960C, be ENEC compliant and be provided with earthing terminal. Theluminaire shall be Concord:marlin 20307022 + 2028037.Note : For luminaire with emergency kit, the sheet steel remote box kit shall consistof converter unit, charger circuit and Ni Cd batteries to ensure operation for 3 hourson mains failure. The luminaire shall be Concord:marlin 20307022 EM + 2028037.IP: 20 40 41. Alternative approved :Zumtobel, WilaLocation of use : VIP AreasLight fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: AQLamp Type : 2 x T5 28 W, Color 830Mounting: SuspendedSpecified : Concord:marlin Ovation 80 228 IP65Detailed specification:Suspended continuous light lines consisting of lighting units as identified in thelighting layout drawings. Each lighting unit (Type AQ) shall be suitable for use with 2x 28W T5 linear fluorescent lamps. The lighting units shall be of extruded aluminumconstruction, with solid aluminum end caps and stainless steel external hardware. Areflector of aluminum shall be provided to ensure sufficient upward and downwardlight output. Curved safety glass shall provide ingress protection. The fixure shall besupplied complete with all accessories, I line couplers, diffusers, suspension kits andpower in feed cables and any other accessory as deemed necessary by theinstallatin to create complete light lines. All high frequency control gear shall beretained internal to the fixture. The luminaire shall be Concord:marlin Ovation 80228 IP65.Note : For luminaire with emergency kit, the kit shall consist of converter unit, chargercircuit and Ni Cd batteries to ensure operation for 3 hours on mains failure, allretained internal to the fixture.IP: 65 41 42. Alternative approved : Zumtobel, WilaLocation of use :Spectator concourseLight fittings specifications :Stadium and Sports Facilities at Shuwaikh CampusType:ARLamp Type :1 x 150 W HIT - CE, Color 830Mounting:Wall mountedSpecified:Hellux 545 WB / 150Detailed specification:Wall mounted luminaire for use with 1 x 150 W HIT CE Metal halide lamp. Theluminaire housing shall be of die cast aluminum with integral control gear box withinthe die cast aluminum mounting spigot of 76 mm dia. A reflector of spun aluminumshall be used for secondary reflection of light. A louver system retained internal to thefixtures shall be used for glare control. The diffuser shall be of unstructured acrylic.The luminaire shall be mounted on a wall bracket of extruded aluminum with armlength not less than 600 mm. The fixture shall be CE compliant and be provided withearthing terminal. The luminaire shall be Hellux 545 WB / 150.IP:6542 43. Alternative approved :Hess, SeluxLocation of use : Concourse circulation areasLight fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: ASLamp Type : 1 x TC TEL 26 W, Color 830Mounting: RecessedSpecified:Concord:marlin 2030718 + 2028607Detailed specification:Recess mounted luminaire for use with 1 x 26 W TC TEL Compact fluorescentlamps. The luminaire housing shall be of die cast aluminum with integral control gearbox of polycarbonate retaining all high frequency dimmable control gear. A highlypolished specular facetted aluminum reflector shall ensure operation efficiency of66%. The luminaire shall conform to LG 7 lighting standards. The cutout dimensionshall not exceed 137 mm diameter and the luminaire shall be provided with a silvercolored trim of a maximum of 11 mm and thickness less than 7 mm to ensurediscreet appearance on installation. A fully internally etched floating glass diffusershall add aesthetic appeal to the luminaire. The luminaire shall be mounted via 3spring clips. The height shall not exceed 98 mm. The luminaire shall be F rated, glowwire tested to 960C, be ENEC compliant and be provided with earthing terminal.The luminaire shall be Concord:marlin 2030722 + 2028607.Note : For luminaire with emergency kit, the sheet steel remote box kit shall consistof converter unit, charger circuit and Ni Cd batteries to ensure operation for 3 hourson mains failure. The luminaire shall be Concord:marlin 2030722 EM + 2028607.IP: 20Alternative approved :Zumtobel, Wila 43 44. Location of use : VIP DiwaniyaLight fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: ATLamp Type : 2 x TC TEL 32 W, Color 830Mounting: RecessedSpecified:Concord:marlin 2038723 + 2039008Detailed specification:Recess mounted luminaire for use with 2 x 32 W TC TEL Compact fluorescentlamps. The luminaire housing shall be of die cast aluminum with integral control gearbox of die cast aluminum retaining all high frequency dimmable control gear. A highlypolished specular facetted aluminum reflector shall ensure operation efficiency of66%. The luminaire shall conform to LG 7 lighting standards. The cutout dimensionshall not exceed 235 mm diameter and the luminaire shall be provided with a silvercolored trim of a maximum of 11 mm and thickness less than 7 mm to ensurediscreet appearance on installation. A frosted glass cylinder shall serve as thelighting element to add aesthetics to the luminaire. The luminaire shall be mountedvia 3 spring clips. The connection of the luminaire to the mains shall be carried outvia rapid connect plug and socket system. The height shall not exceed 156 mm. Theluminaire shall be F rated, glow wire tested to 960C, be ENEC compliant and beprovided with earthing terminal. The luminaire shall be Concord:marlin 2038723 +2039008.Note : For luminaire with emergency kit, the sheet steel remote box kit shall consistof converter unit, charger circuit and Ni Cd batteries to ensure operation for 3 hourson mains failure. The luminaire shall be Concord:marlin 2038723 EM + 2039008.IP: 20Alternative approved :Wila, Hoffmeister 44 45. Location of use :VIP DiwaniyaLight fittings specifications :Stadium and Sports Facilities at Shuwaikh CampusType:AULamp Type :2 x 9 W TC - SEL, Color 830Mounting:SurfaceSpecified:Concord Lumiance 3030290Detailed specification:Ceiling / Wall surface mounted luminaire for use with 2 x TC SEL 9 W compactfluorescent lamps. The luminaire shall be of polycarbonate construction with whitefinished body and opal polycarbonate diffuser to ensure non flashed appearancewhen lit. The luminaire diameter shall be limited to 235 mm and the height of theluminaire shall be restricted to 92 mm to limit projection based on the crampedlocation of installation. All high frequency control gear shall be retained internal to thehousing. The fixture shall be ENEC certified, be provided with a separate earthingterminal and F rated for 850C and in white finish. The luminaire shall be ConcordLumiance 3030290.IP:44Alternative approved : Erco, ASD45 46. Location of use : Lift wellsLight fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: AVLamp Type : 8 x 28 W T5, Color 830Mounting: SuspendedSpecified:Concord:marlin 4x(2038221+1929182) + 3x2038197 +2x2038202 + 5x2032321 + 1x2032318 + 2x2034276Detailed specification:Suspension mounted light line consisting of 4 lighting units. Each lighting unit shall besuitable for use with 2 x 28 W T5 lamps. The housing of each lighting unit shall be ofextruded aluminum in oval cross section width not more than 200 mm and heght 65mm to meet with the architectural feature and requirement. Each lighting unit shallalso be provided with a low glare super pure aluminum reflector and a prismaticdiffuser to provide 43 % direct and 36% indirect lighting output. The lighting unitsshall be coupled with dummy sections each of equal length to complete the light lineand meet with the architectural requirements. All high frequency dimmable contolgear shall be retained internal to the housing of each unit. The light line shall besuspended via suitable adjustable suspension drops and shall be provided withtapered end caps of approximately 120mm length. The light line system shall be insilver finish and complete in all respects in terms of accessories, inclusive and notlimited by the items identified here. The system shall be Concord:marlin4x(2038221+9129182) + 3x2038197 + 2x2038202 + 5x2032321 + 1x2032318 +2x2034276.Note : For luminaire with emergency kit, the kit shall consist of converter unit, chargercircuit and Ni Cd batteries to ensure operation for 3 hours on mains failure locatedintegral to one of the lighting units. TIP: 20Alternative approved :Zumtobel, Thorn 46 47. Location of use : Meeting roomsLight fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: AWLamp Type : 1 x 70 W HIT - DE, Color 830Mounting: Wall surfaceSpecified:Concord:marlin 4064163Detailed specification:Surface mounted luminaire for use with 1 x 70 W HIT DE double ended Metal halidelamp. The luminaire housing shall be of die cast aluminum with all control gearmounted integral to the housing. A highly polished specular anodized aluminumasymmetric reflector shall ensure high operation efficiency and forward throw lightdistribution. The luminaire dimension shall not exceed 350 mm diameter andprojection from wall of 180 mm. The luminaire shall be finished black polyesterpowder coat. The front of the luminaire shall be protected by a toughened glass paneto ingress protect the luminaire alongwith eyelid to limit upward light output. Allexternal hardware shall be in Stainless steel. The luminaire shall be F rated, beENEC compliant and be provided with earthing terminal. The luminaire shall beConcord:marlin 4064163.IP: 65Alternative approved :Bega, WeefLocation of use : Roof 47 48. Light fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: AYLamp Type : 1 x 70 W HQI - TS, NDLMounting: Ceiling recessedSpecified:SBP 05087794Detailed specification:Ceiling recess mounted luminaire for use with 1 x 70 W HQI - TS double ended Metalhalide lamp. The luminaire housing shall be of die cast aluminum chromate pretreated and finished polyester coat RAL 9006. A highly polished specular polishedaluminum asymmetric reflector shall ensure high operation efficiency and Imax = 45.A 5 mm thick front glass with anti aging dual foam silicon gasket directly injected ontoit shall ingress protect the fixture. All control gear shall be retained on a galvanizedsheet steel gear tray. A recess mounting frame in steel shall ensure proper mounting.All external hardware shall be in stainless steel. All external hardware shall be inStainless steel. The luminaire shall be F rated, IK 08, 7J, be ENEC compliant and beprovided with earthing terminal. The luminaire shall be SBP 05087794.IP: 66Alternative approved :Norlight, Philips, SilLocation of use : Squash courtsLight fittings specifications : Stadium and Sports Facilities at Shuwaikh Campus 48 49. Type: BALamp Type : 2 x 250 W NAV - TMounting: StreetlightSpecified : MEW Standard 2 x 250 W on 8 meter high poleDetailed specification:As per MEW standardAlternative approved :MEW standardLocation of use : Car park and internal roadsLight fittings specifications : Stadium and Sports Facilities at Shuwaikh Campus49 50. Type: BBLamp Type : 1 x 250 W NAV - TMounting: StreetlightSpecified : MEW Standard 1 x 250 W on 8 meter high poleDetailed specification:As per MEW standardAlternative approved :MEW standardLocation of use : Car park and internal roadsLight fittings specifications : Stadium and Sports Facilities at Shuwaikh Campus50 51. Type: BCLamp Type : 1 x 150 W HCI - T, Color 830Mounting: IngroundSpecified : SBP Cricket 25 05162504Detailed specification:In ground luminaire for use with 1 x 150 W HCI T Metal halide lamp. The luminaireenclosure shall be in corrosion proof tecnopolymer, and housing in die cast aluminumwith a AISI 316 grade stainless steel frame. An IK10 24 J toughened safety glassset in an anti ageing silicon gasket shall impart ingress protection to IP 67. A 0 to-10 adjustable reflector of high purity anodized aluminum shall ensure Imax 6200cd/klm with a 2 x 7 light beam. The luminaire shall be provided with M20 x1.5 cableentry gland to accommodate upto 12mm cable and 2 x 2.5mm automatic isolatingterminals to interrupt power supply for safe maintenance. The luminaire shall becapable of handling upto 12000 Kgs gross weight at speeds of 30kmph. Maximumexternal operating glass temperature shall be 110C to ensure safe operation. Theluminaire shall be CE compliant and Class II. The luminaire shall be SBP Cricket 2505158590.IP: 67Alternative approved :Weef, BK LightingLocation of use : Tree uplightersLight fittings specifications : Stadium and Sports Facilities at Shuwaikh Campus 51 52. Type:BDLamp Type :1 x 70 W HIT - CE, Color 830Mounting:Ground mounted bollardSpecified : SBP 05153304Detailed specification:Ground mounted bollard luminaire for use with 1 x 70 W HIT CE Metal halide lamp.The luminaire shall have housing in AISI 316 grade stainless steel with a die castaluminum mounting base. A diffuser in IK10 impact resistant polycarbonate shallingress protect the fixture. A double reflector in anodized and polished aluminumshall ensure zero upward distribution conforming to Zone 1 UNI 10819 and Imax atapproximately 50. All control gear shall be retained within a tecno polymer controlgear housing integral and internal to the fixture. The luminaire shall be provided withanti tear glasnd, anti aging silicon gaskets, and stainless steel external hardware.The luminaire shall be at least 155mm in diameter and at least 900 mm height. Theluminaire shall be CE compliant and Class I. The luminaire shall be SBP 05153304.IP:66Alternative approved : Weef, BegaLocation of use :Landscape areaLight fittings specifications :Stadium and Sports Facilities at Shuwaikh Campus52 53. Type: BFLamp Type : 2 x 150 W T 5, Color 830Mounting: Pole top mountedSpecified : 2 x Hellux 545 PT / 150 + 6 m ALpole + 150813Detailed specification:Pole light system consisting of 2 lighting units each equipped with 1 x 150 W HIT CE metal halide lamp. The extruded aluminum pole shall be of 6 meters height andhave a cross am bracket 1100 mm wide c to c, twin layered. Each lighting unitshall be mounted atop the end of the bracket via a vertical mounting piece at least480 mm high. Each lighting unit top mounted luminaire shall be for use with 1 x 150W HIT CE metal halide lamps. The luminaire housing shall be of die cast aluminumwith integral control gear box within the die cast aluminum mounting spigot of 76 mmdia. A reflector of spun aluminum shall be used for secondary reflection of light. Alouver system retained internal to the fixtures shall be used for glare control. Thediffuser shall be of unstructured acrylic. The fixture shall be CE compliant and beprovided with earthing terminal. The lighting system shall be 2 x Hellux 545 PT / 150+ 6 m ALpole + 150813. 53 54. IP:65Alternative approved : Hess, SeluxLocation of use :Landscape area VIP entranceLight fittings specifications :Stadium and Sports Facilities at Shuwaikh CampusType:BGLamp Type :2 x 28 W T 5, Color 830Mounting:SurfaceSpecified:SBP LF4 05132111Detailed specification:Surface mounted luminaire for use with 2 x T5 28 W fluorescent lamps. The luminairehousing shall be of extruded aluminum, structurally strong and corrosion resistant. Itshall be an anodized extruded aluminum body with V0 UL94 (850d C) tecno polymerhead parts. The reflectors shall be of anodized polished very pure aluminum andensure efficiency of 59% and a light distribution of 2 x 53 along axis parallel tolamps and 2 x 61 along axis perpendicular to lamps. A toughened safety glasshinged to the body and retained within silicone gaskets and by stainless steelhardware. The luminaire shall be supplied complete with 2 strong AISI 316 stainlesssteel springs for ceiling safe quick fixing. The composition of materials ofmanufacture shall be 96% non combustible materials to V0-UL94 with the remaining4% in self extinguishable VO-UL94 and glow wire resistant to 850C. All highfrequency control gear shall be retained internal to the luminaire. The luminaire shallbe IK08, 6J, F rated, glow wire tested to 850C and be provided with earthingterminal. The luminaire shall be SBP LF4 05132111.54 55. IP: 66Alternative approved :Trilux, CromptonLocation of use : External covered car parksLight fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: UWLamp Type : 1 x PAR 56 12 V 300 WMounting: Wall recessedSpecified:SBP 01003202+14410998Detailed specification:Wall recess mounted luminaire for use with 1 x PAR 56 12 V 300 W PressedAluminum reflector lamp. Housing made from tecnopolymer ij heat resistant U VStabilized and reinforced PPH material. The recess housing shall also be intecnopolymer with all all control gear and transformer separately mounted in suitablelocation as per site conditions. The fixture shall be provided with at least 4 meters offactory fitted H07 RNF 2 x 4 cable. The luminaire shall be CE compliant, ElectricalClass III. The luminaire shall be SBP 01003202 +14410998. 55 56. IP: 68Alternative approved :Bega, WibreLocation of use : Swimming pool and Diving poolLight fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType:F1Lamp Type : 1 x HIT DE 2000WMounting: ABOVE TOWERSpecified:FRANZ SILL: 003 * 200 33Detailed specification:Standard colour: natural aluminiumHousing with large heat dissipating cooling fins is made of Si12 corrosion resistantdie-cast aluminium. Strengthened main reflector made of 99.98% pure aluminium,chemically polished and anodised with built-in anti-glare shield.The toughened frontglass, protected by a fine stainless steel mesh, is silicon sealed into the diecastaluminium bezel. The reflector is embedded in a die-cast aluminium, heat finnedsupport ring, itself pivoting (with aiming angle protractor) on the mountingstirrup.Twin, easy-grip catches for rear opening lamp compartment with aiminghandle; opening does not affect projector aiming.Usage For long distance illumination, for sports stadium andspecial floodlight.Protection rating IP 65Lamp Wattage2000 WLight distributionnarrow beam, deep wide beam, wide beam, super-widebeam 56 57. Lamp choice HIT-DEIP:65Alternative approved : Thorn, SBP RayLocation of use :Main StadiumLight fittings specifications: Stadium and Sports Facilities at Shuwaikh CampusType:F2Lamp Type :1 x 2000 W MHN LA / 842 Metal halide lampMounting:Pole mountedSpecified:SBP LaserDetailed specification:Asymmetric floodlight luminaire for use with 1 x 2000 W MHN LA Metal halide lampwith lumen output of 220000 lumens and 3 mains supply. The luminaire housingwith cooling fins shall be of die cast aluminum chromate pretreated and finishedpolyester RAL 9006. The luminaire shall have a die cast aluminum rear access panelhinged to ensure relamping during maintenance without disturbing the aimingposition, a die cast aluminum wiring box with tecnopolymer cover shall retain thetriple pole ignitor. A reflector of high purity aluminum anodized and polished shall beavailable to ensure 2 optional light distributions with maximum intensity approx750cd/Klm and 1650cd/ KLM both with Imax at 45. A stainless steel clip shll beprovided to steady the lamp position and prevent lamp vibration. A toughened safetyglass with an anti aging dual foam silicone gasket, factory injection directly onto theglass during CNC process, and, hinged to the body by stainless steel clips shallingress protect the fixture. A mounting bracket in steel hot dip galvanized with 5graduated goniometer shall be provided for aiming and adjustment. All externalhardware shall be in stainless steel. The lamp shall be double ended with lamp cap -base X 528, 4200K color temperature and Ra = 80 or higher. The windage area ofthe luminaire in the axis parallel to the lamp shall be < 0.40m and that in the axisperpendicular to the lamp < 0.16m with the dead weight of the luminaire beinglimited to 22.50kgs. The luminaire shall be IK08, 8J, F rated and be provided withearthing terminal. The luminaire shall be SBP Laser.57 58. IP: 65Alternative approved :Thorn, SillLocation of use : Training pitch - FootballLight fittings specifications : Stadium and Sports Facilities at Shuwaikh CampusType: F 3 / FL6 / FL7Lamp Type : 1 x 1000 W HPI - T Metal halide lampMounting: Pole or structure mountedSpecified:SBP 5Stars 1000Detailed specification:Compact lightweight high performance floodlight luminaire for use with 1 x 1000 WHPI-T Metal halide lamp with lumen output of 85000 lumens, 4300K, and 1 mainssupply. The luminaire housing shall be of die cast aluminum chromate pretreated andfinished polyester RAL 9006. An asymmetrical of high purity 99.98% heavy gaugealuminum anodized and polished shall ensure Imax at 45 of about 500cd/klm.Polyamide lamp holder shall ensure precise lamp positioning and a polyamide wiringbox shall be house the ignitor. A 5mm toughened safety glass with an anti aging dualfoam silicone gasket, factory injection directly onto the glass during CNC process,and, hinged to the body by stainless steel clips shall ingress protect the fixture. Apolyamide IP66 anti vacuum device without filters shall be used for pressurestabilization. A mounting bracket in steel hot dip galvanized with 5 graduatedgoniometer shall be provided for aiming and adjustment. All external hardware shallbe in stainless steel. The windage area of the luminaire shall be < 0.20m with thedead weight of the luminaire being limited to 11.20kgs. The luminaire shall be ENECapproved, CE compliant, IK08, 5J, F rated and be provided with earthing terminal.The luminaire shall be SBP 5Stars 1000.Note : Fixtures for use on Emergency mode shall be equipped with Hot restrikecontrol gear to ensure instant restrike of the lamp when emergency power isrestored.58 59. IP:66Alternative approved : Sill, PhilipsLocation of use :Mutipurpose Hall, Swimming Hall, Training Basketball courtLight fittings specifications :Stadium and Sports Facilities at Shuwaikh CampusType:F4Lamp Type :1 x 400 W HPI - T Metal halide lampMounting:Pole mountedSpecified:SBP Leo 5057994Detailed specification:Asymmetric floodlight luminaire for use with 1 x 400 W MHN LA Metal halide lampwith lumen output of 35000 lumens and 1 mains supply. The luminaire housingwith shall be of die cast aluminum chromate pretreated and finished polyester RAL9006. A reflector of high purity aluminum anodized and polished shall be provided toensure asymmetrical light distribution with Imax at 40. A 5mm thick toughenedsafety glass with an anti aging dual foam silicone gasket, factory injection directlyonto the glass during CNC process, and, hinged to the body by stainless steel clipsshall ingress protect the fixture. A mounting bracket in steel hot dip galvanized shallbe provided for aiming and adjustment. All external hardware shall be in stainlesssteel. The windage area of the luminaire in the axis parallel to the lamp shall be 90m.Color temperature K :5600Kn.Main camera :1 no. as specified and located per playing areao.Secondary cameras :5 nos. placed around principal playing area one at each corner and one opposite to main camera.p.Observer points :19 nos.q.Lamp lumen output :200000 lumensThe luminaire incorporated in the design of the lighting system shall be Type F 1 andcomply with all specifications as detailed under Type F 1. The lighting system shallcomply with the specifications and lighting parameters defined under Table 1 Mainstadium lighting system.The control gear shall be mounted in special customized panels, sufficientlyventilated and cooled. Each mast shall have an independent panel in close proximityto the mast and shall allow for switching of the lighting system from Switch Mode toSwitch Mode to testing and maintenance purposes. A central Switch Mode Selectorpanel located in the central control room shall be used to select the required switchmode and control all the four masts. The panels and Switch Mode selector shall beas per details indicated in drawings and to engineers final approval. The systemshall provide to extreme flexibility in terms of usage. Control gear suitable for Hotrestrike operation of the lamps shall be used to address Switch Modes 5 and 6.The fixtures shall be mounted atop masts of 40 meters height. The masts shall becompliant to current standardsA single high mast with its own luminaires shall be read as Type FL 1. This shall belimited to a 40 meter high mast with 48 numbers of fixtures, each 2 KW.Light fittings specifications : Stadium and Sports Facilities at Shuwaikh Campus79