apt dual clutch
TRANSCRIPT
-
8/13/2019 APT Dual Clutch
1/26
Guided By, Prof. P. BaskarSMBS
VIT University
Seminar by,Sanchit jain
13MAE0012
-
8/13/2019 APT Dual Clutch
2/26
-
8/13/2019 APT Dual Clutch
3/26
Introduction All-Terrain Vehicles (ATVs) are frequently used for off-roaddriving, including agricultural and traction work, and there is astrong demand for easy operation.
ATs waste engine power in the transmission mechanism, resultingin a degradation of fuel consumption and dynamic performance,so they developed a dual-clutch transmission for ATVs.
The dual-clutch transmission provides better fuel consumptionand dynamic performance than other ATs.
-
8/13/2019 APT Dual Clutch
4/26
Problems
Development of DCT.
Hammering noise at the time of engagement.Complex mechanism of DCT.Gear shift mechanism with shift drum.Cost
-
8/13/2019 APT Dual Clutch
5/26
Mechanism
-
8/13/2019 APT Dual Clutch
6/26
-
8/13/2019 APT Dual Clutch
7/26
Structure of DCT.Structure 0f transmission.Structure of pre-shift.
Gear change process.
-
8/13/2019 APT Dual Clutch
8/26
Noise
The hammering noise fromthe dog clutch mainlyresults from the rotationalkinetic energy caused by thedifference between therotating speeds of gear andshifter when the dog clutch isengaged. This rotational
kinetic energy is transducedinto noise and heatgenerated at the collision ofthe dog and the pocket.
-
8/13/2019 APT Dual Clutch
9/26
Motion of Shift drum
-
8/13/2019 APT Dual Clutch
10/26
Result
-
8/13/2019 APT Dual Clutch
11/26
Result
A dual-clutch transmission utilizing a gear train with dog-clutch was developed successfully.Hammering noise caused by the engagement of the dog-
clutch was reduced by control of the motor-driven shift andgear shift mechanisms. The basic design of the gear is the same as that in a MT,though the main shaft structure and the layout of gear stages
are different. A dual-clutch transmission using a gear shift mechanism with shift drum was developed successfully.The clutch, transmission axis, and gear shift axis are the same
as those in a MT.
-
8/13/2019 APT Dual Clutch
12/26
-
8/13/2019 APT Dual Clutch
13/26
Introduction
At present, there are no clear criteria to judge the quality of shiftquality and shift control effect about DCT . That is, based on theshock of degree, work of slipping which is produced by
transmission system to assessment the shift quality roughly.
This paper took the research on shift quality evaluation andoptimization of a DCT prototype, on the one hand, the controltarget and control method On the other hand, it is optimized thecontrol strategy and control algorithm of DCT system.
-
8/13/2019 APT Dual Clutch
14/26
Problems-
Control strategy.Performance Evaluation.
Optimization.Cost analysis.
-
8/13/2019 APT Dual Clutch
15/26
Guaranteeing the vehicle dynamic performance and thelife time of power transmission system, shifted quicklyand smoothly and meet comfort requirements.
Large fluctuations, flutter, flame out and destroy thesmooth of shifting if the clutch engaging too fast; To thecontrary, if the clutch engaging too slow, the slipping
work will increase quickly and reducing the clutchservice life.
Shift quality evaluation
-
8/13/2019 APT Dual Clutch
16/26
Model and evaluation system design
-
8/13/2019 APT Dual Clutch
17/26
-
8/13/2019 APT Dual Clutch
18/26
Steps for Systematic Gear Set Development
-
8/13/2019 APT Dual Clutch
19/26
The simulation platform which based on the vehiclesystem model and evaluation system integrationreaches the evaluation index of control expectedinterval when shift quality evaluation achieved optimalthrough the evaluation.
The optimal control targets of DCT system shift qualityand ensuring each index fell on within the control
expectation interval, it can guarantee the DCT has goodshift quality by compromising each index.
-
8/13/2019 APT Dual Clutch
20/26
Results of Optimization
The fuzzy control rules of clutch
engaging speedregulation after optimizing
The fuzzy control rules of throttle
adjustment afteroptimizing
-
8/13/2019 APT Dual Clutch
21/26
Results
The simulation curve of shifting with full throttle
-
8/13/2019 APT Dual Clutch
22/26
-
8/13/2019 APT Dual Clutch
23/26
Thank You
-
8/13/2019 APT Dual Clutch
24/26
QURRIES
-
8/13/2019 APT Dual Clutch
25/26
1. Control of hammering noise-Methods are available to minimize the impact energy of dog-clutch
engagement to be absorbed Decreasing the inertial mass of the shifter system Decreasing the ratio difference Decreasing the difference in rotational speed
2. How do we control pre-shift mechanism.
The feed control of motor-driven shifting is divided into eightsteps to accommodate the above mechanism, and the motoroutput (Duty value) and time are controlled for each step .
3. Why were they not using the synchronization mechanism.
The synchronization mechanism leads to a larger transmission size,heavier weight, and a cost increase due to the increased number ofparts.
1st paper-
-
8/13/2019 APT Dual Clutch
26/26
2nd paper-