appliqued checkbook cover.pdf

7/17/2019 Appliqued Checkbook Cover.pdf

1/18


2/18

1

Make sure print setting is set at Do Not Scale or 100% Scale." Always printActual Size.

Feel free to sell your bags made with my pattern but please do not sell or share the pattern.

Copyright 2015 - RLR Creations

Materials Needed:

3/4 yard 44 wide quilting cotton weight Main Fabric

3/4 yard 44 wide quilting cotton weight Lining Fabric

1 1/2 yards 20 Fusible Pellon 808 Craft Fuse (heavier non woven) Interfacing

Small Piece Ultra Firm Fusible Stabilizer Peltex 71F- to measure at least 10 x 10

Clear Vinyl Piece Aprox. 24 x 42

Coordinating thread

Removable Fabric Marker (I recommend a Frixion gel pen as it can be removed by

pressing with an iron)

Microtex (Sharp) Needle 80/12 Recommended for topstitching.

Optional: Needed for the Carry Strap

1- D-Ring

1- 1 Swivel Hook

Cutting:

Here is a cut list for all pieces.

Piece A- Bottom: Cut from Pattern Piece Provided Cut 1 Main Fabric, Cut 1 Lining Fabric, Cut 1 Interfacing, Cut 1

Clear Vinyl

Piece A: Bottom Stabilizer:Cut from Pattern Piece Provided

Piece B- Side Panels: 30 W x 12 H - Cut 1 Main Fabric, Cut 1 Lining Fabric, Cut 1 Interfacing, Cut 1 Clear Vinyl

Piece C-Accent Band: 30 W x 4 H - Cut 1 Lining Fabric

Piece D-Bias Binding: 30- W x 1 1/2 H- Cut 1 Lining Fabric

Piece E-Top Band: 30 W x 4 1/2 H Cut 2 Exterior, Cut 1 Interfacing

Piece F-Pocket Panel:30 W x 8 H Cut 1 Clear Vinyl

Piece G-Drawstring Carry Strap: WOF W x 2 H Cut 2 Main Fabric OR 1 Lining Fabric-your choice, Cut 1

Interfacing 80W x 2 H


3/18

2

Fabric Layouts:


4/18

3

Preparing:

Interfacing- Fuse interfacing to WRONG SIDE of each corresponding Main Fabric pieces.

Fuse the Piece A stabilizer centered overtop the interfaced Piece A Bottom Main Fabric.

INSTRUCTIONS TO COMPLETE BAG:

DRAWSTRING CARRY STRAP:

1. Using the two Piece Gs you cut, long lay one piece down RIGHT SIDE UP horizontally. Place the second piece on top

vertically RIGHT SIDE DOWN (two strips will be right sides together) at the edges with a slight overlap at the edges.


5/18

4

2. Draw a diagonal line from the top left corner to the bottom right corner. Pin pieces together and sew across the line

making sure to backstitch at the beginning and end. Trim to 1/4 seam allowance on outside of stitched line. Press the

seam open.

3. Fuse the Piece G interfacing piece you cut to wrong side.

4. With the WRONG SIDES TOGETHER fold a strap piece in half lengthwise and press to create a crease then open.

5. Now fold each edge towards center crease and press. Fold in half and press again.

6. Top Stitch across both long sides about 1/8 from edge.

STRAP CONNECTOR:

7. Cut a 2 piece from the finished strap.

8. Slip the D ring onto 2 piece you just cut. Fold in half matching the raw edges and having the ring at the fold. Stitch

across the connector piece as close to the ring as possible.

Drawstring is now complete. Set pieces aside.


6/18

5

Preparing and Attaching the Accent Panel:

1. Take the Piece C- Accent Band and fold in half lengthwise. Press to create a crease line.

2. Open the piece up and with WRONG SIDE UP fold each raw edge towards the center.

Piece now should measure 2 wide.

3. Take the Piece B- Side Panel Main Fabric and place RIGHT SIDE UP. Place the finished Piece C Accent Band on top

RIGHT SIDE UP (folded in edges down) 2 above the bottom raw edge of the Side Panel. Pin in place.

4. Edge stitch with 1/8 seam allowance across the top and bottom of the Accent Band to attach.


7/18

6

Assembling the Outside of the Bag:

1. Fold the finished Main Fabric Piece B in half matching the two short sides and the edges of the Accent Piece you

added; RIGHT SIDES TOGETHER. Pin short raw edges together.

2. Sew down the pinned edge with seam allowance.

3. Press the seam open, turn RIGHT SIDE OUT and press well to flatten the seam.

Your finished outside piece will now resemble a cylinder.

Adding the Bottom Piece A Main Fabric

5. Turn your finished Side piece WRONG SIDE OUT.

Adding the Connector Piece:


8/18

7

Baste the D-ring piece you just made to Piece A Main Fabric Bottom by matching the raw edges of the D-ring

piece with the raw edge of the Bottom piece and stitching in place.

6. Pin or clip the Bottom (Piece A) to the bottom of the Side Panel you just completed RIGHT SIDES TOGETHER, easing

the two pieces together to completely pin or clip the Bottom to the Exterior Side Panel all the way around. Align the d-

ring with the seam on Piece B-Exterior Main panel.

NOTE:It is best to pin or clip every or so to help hold everything in place as you sew around the bottom.

7. Sew all the way around the bottom against the stabilizer piece with seam allowance to attach the Bottom Panel to

the Finished Exterior.

8. Trim the seam allowance down to and turn RIGHT SIDES OUT. Press well around the bottom seam to flatten.

Outside of the bag is done!


9/18

8

Assembling the Inside of the Bag:

Note: A Teflon foot is ideal for sewing on vinyl. If you do not have a Teflon Foot you can put a piece of scotch

tape on the bottom of your pressure foot to keep the vinyl from sticking to your foot.

Making Bias Tape and adding to Vinyl Pocket:

1. With the WRONG SIDES TOGETHER fold the Piece D- Bias in half lengthwise and press to create a crease.

2. Open the piece and press the long edges on both side into the crease you just made; WRONG SIDES TOGETHER.

3. Fold the piece in half again on the crease you originally pressed.

Finished Bias Tape should measure approximately 3/8

4. Lay the Piece F Pocket Vinyl piece with longest side facing up. Fold the finished Piece D bias over the edge of the viny

encasing the top edge within the folded bias.


10/18

9

5. Stitch the Bias Tape in place with a 1/8 seam across the bottom edge.

Making the Pockets and finishing the Inside of the Bag:

1. Lay the Piece B Side Panel Lining Fabric RIGHT SIDE UP. Place the Piece B Side Panel Clear Vinyl piece on top.

2. Place the finished Clear Vinyl Pocket Panel on top of the two pieces matching the bottom and side raw edges. Clip the

three layers together with Wonder Clips or paper clips.

NOTE:Do not use pins with the clear vinyl as they will leave holes in the vinyl.

3. Baste along all four sides as close to the edge as possible.

4. Dividing the Pockets: Divide the pocket panel as you desire by sewing vertical lines down the pocket panel; through al

of the layers. Backstitch several times at the beginning and end of the line to reinforce.


11/18

10

Pockets are finished!

Finishing the interior:

1. Place the Piece A-Bottom Liner Fabric RIGHT SIDE UP, then place the Piece A- Bottom Clear Vinyl on top and clip in

place.

2. Baste around the pieces as close to the edge as possible.

Set Aside.

NOTE: The interior lining is assembled in the same manner as you completed the outside of the bag on pages 7-

8 you can follow the same diagrams on these pages.


12/18

11

3. Fold the finished Interior Piece B in half matching the two short sides RIGHT SIDES TOGETHER. Clip short raw edges

together.

4. Sew down the clipped edge with seam allowance.

Adding the bottom Piece A Main Fabric

5. Keep your finished piece WRONG SIDE OUT.

6. Clip the Finished Bottom Piece to the bottom of the Side Panel you just completed RIGHT SIDES TOGETHER, easing the

two pieces together to completely clip the Bottom to the Interior Side Panel all the way around.

NOTE:It is best to clip every or so to help hold everything in place as you sew around the bottom.

7. Sew all the way around the bottom with seam allowance to attach the Bottom Panel to the Finished Interior.

8. Trim the seam allowance down to and keep the piece WRONG SIDE OUT.

Inside of the bag is done!

Making the Top Panel:

1. Place the two Piece E Top Panels RIGHT SIDES TOGETHER and pin in place. Sew across the top (long side) with

seam allowance.

2. Open the piece press the seams open.

3. Keep the piece fully open with the seam you just pressed in the center. On the WRONG SIDE of piece mark the

placement for the drawstring opening as follows:

With the piece fully open, and the seam in the center, measure down 1 from the top on both sides and mark

a line.

Measure down again from the top 2 and mark a line.

From the bottom of the piece measure up 1 and mark a line on both sides.

Measure up again from the top 2 and mark a line.


13/18

12

You should now have 4 marked lines on each side as shown in the above diagram.

4. Fold the piece in half lengthwise (short sides), RIGHT SIDES TOGETHER, matching the short raw edges and aligning the

marks you made on both sides and keeping the seam in the center.

From the top sew down to the first mark with a seam allowance backstitching when you start and when you reach

the mark.

Start stitching again at the second mark to the third mark, again backstitching at the beginning and when you reach themark.

Stitch again from the fourth mark to the bottom of the piece backstitching when you start at the mark and when you

reach the end.

Your top panel will now be a circle and you will have an opening to add the drawstring. Press open the seam you just

created and turn RIGHT SIDE OUT.

5. Fold the piece in half with the center long seam now at the top of the piece. WRONG SIDES TOGETHER.

You will now have a piece that measures 3 with long seam at the top and the raw edges at the bottom with RIGHT

SIDES of the fabric on both the front and back of the band.

Topstitch all the way around the Piece (circle) at the fold (raw edges are the bottom and seam at the top) away from

the top seam.

Now we will finish making the drawstring opening and make a stitch line to aid in folding up the raw edges to

on the bottom of the piece:

6. With a removable fabric pen mark a line all the way round the piece 1 up from the bottom.

Mark another line all the way around the piece 1 up from the bottom.

Mark a third line 2 up from the bottom.

7. Sew around the piece on each line you just created. You will now have 4 stitched lines around the Top Panel (this

includes the topstitching around the top of the piece you did in Step 5).

NOTE: Do not sew through the layers but rather around the circle piece you created.


14/18

13

8. Fold the raw edges on both sides of the band towards the bottom stitched line, all the way around and press.

This will allow you to not have any raw edges at on your finished bag.

After both raw edges on the front and back of the band are folded up you will now have an opening to attach to

the finished bottom pieces. Top Panel Piece is now finished.


15/18

14

Assembling and completing the bag:

1. Take the completed interior bottom and place inside the completed exterior bottom WRONG SIDES TOGETHER;

matching the top raw edges.

2. Place the Top Band piece over the top raw edges of the bottom pieces in between the bottom edges you folded up

till the bottom pieces raw edges meet the bottom stitched line. Be sure that the drawstring opening seam is aligned with

the Exterior Side Panel seam so that you can connect the drawstring piece to the d-ring on the bottom.

You are enclosing the top raw edges of the bottom of the bag between the front and back folded edges at the

bottom of the top panel piece.

3. Pin in place; placing the pins horizontally across the piece close to the bottom stitched line on the top panel so that

you do not make holes in your clear vinyl piece.

4. Stitch around the assembled piece to attach the top panel to the bottom about above the bottom of the top panel

For the Carry Strap:

1. Thread the drawstring though the drawstring opening making sure to keep both ends even.


16/18

15

2. Thread both pieces through the trigger snap side by side, making sure the pieces are not twisted and both lay flat

RIGHT SIDES UP after threading though the trigger snap.

Note: You can shorten the straps at this point for a custom length by simply pulling the raw ends up and cutting

excess off.

3. Make sure the end of the straps go past the D ring of the trigger snap by at least an inch. Fold back the ends of each

to enclose the raw edges.

4. Keep the strap pieces side by side and sew across both several times to secure to the trigger snap.

5. Connect the trigger snap to the d-ring on bottom of bag to finish the carry straps.

Your bag is now complete and ready for you to fill with all your ditties!


17/18

BottomA

Cut 1 Main FabricCut 1 Lining FabricCut 1 InterfacingCut 1 Clear Vinyl

Ditty Bag

Cr

eation

s

Sewing Patterns 2015 RLR Creations

1

Place

on

Fold


18/18

Ditty Bag

Creation

s

Sewing Patterns 2015 RLR Creations

Bottom

Stablizer

A

Cut 1 Stiff

Stablizer

P

lace

on

Fol d

appliqued checkbook cover.pdf

Documents