ap 4532 install guide

Extreme Netw3585 Monroe Santa Clara, C(888) 257-300(408) 579-280http://www.ex

Altitud ess Point Installation Guide

Published: OcPart number: orks, Inc.Streetalifornia 9505100tremenetworks.com

tober 2012120791-00 Rev 02e 4532 Series Acc

2AccessAdapt, Alpine, Altitude, BlackDiamond, EPICenter, ExtremeWorks Essentials, Ethernet Everywhere, Extreme Enabled, Extreme Ethernet Everywhere, Extreme Networks, Extreme Standby Router Protocol, Extreme Turbodrive, Extreme Velocity, ExtremeWare, ExtremeWorks, ExtremeXOS, Go Purple Extreme Solution, ExtremeXOS ScreenPlay, ReachNXT, Sentriant, ServiceWatch, Summit, SummitStack, Triumph, Unified Access Architecture, Unified Access RF Manager, UniStack, the Extreme NetwSummit logosExtreme Netw

sFlow is a reg

Specifications

All other regisowners.

2012 ExtremAltitude 4532 Series Access Point Installation Guide

orks logo, the Alpine logo, the BlackDiamond logo, the Extreme Turbodrive logo, the , and the Powered by ExtremeXOS logo are trademarks or registered trademarks of orks, Inc. or its subsidiaries in the United States and/or other countries.

istered trademark of InMon Corporation.

are subject to change without notice.

tered trademarks, trademarks, and service marks are property of their respective

e Networks, Inc. All Rights Reserved.

Altitude 453

Table of Contents

Chapter 1: IDocumenWarningsSite PrepAltitude 4

ExteInteg

Features.

Chapter 2: HInstallatioPrecautioAccess PIntegrated

Wall Wall

IntegratedT-Bar Mo

SuspExternal A

Wall Wall

External ASuspCeilin

Antenna OLED Indic

Chapter 3: DUsing the

Chapter 4: SAltitude 4Altitude 4532 Access Point External Antenna Model Physical Characteristics......................... 452 Series Access Point Installation Guide3ntroduction....................................................................................................5t Conventions............................................................................................................... 6..................................................................................................................................... 6aration .......................................................................................................................... 7532 Access Point Package Contents........................................................................... 7rnal Antenna Model Package Contents ........................................................................ 7rated Antenna Model Package Contents ..................................................................... 7..................................................................................................................................... 8

ardware Installation ....................................................................................9n Instructions ............................................................................................................... 9ns............................................................................................................................... 10oint Placement ........................................................................................................... 11 Antenna Model Wall Mount Instructions .................................................................. 11

Mount Hardware ........................................................................................................ 11Mount Procedure ....................................................................................................... 13 Antenna Model Suspended Ceiling

unt Instructions........................................................................................................... 15ended Ceiling Mount Procedure................................................................................ 15ntenna Model Wall Mount Instructions ..................................................................... 16

Mount Hardware ........................................................................................................ 16Mount Procedure ....................................................................................................... 17ntenna Model Suspended Ceiling Tile (Plenum) Mount Instructions........................ 18

ended Ceiling Mount Hardware................................................................................. 19g Mount Procedure ................................................................................................... 19ptions for Altitude 4532 Access Point External Antenna.......................................... 20

ators .......................................................................................................................... 21

efining A Basic Configuration..................................................................22 Initial Setup Wizard................................................................................................... 22

pecifications ..............................................................................................45532 Access Point External Antenna Model Electrical Characteristics ....................... 45

Table of Contents

4

Altitude 4532 Access Point Integrated Antenna Model Electrical Characteristics .................... 46Altitude 4532 Access Point Integrated Antenna Model Physical Characteristics...................... 46Radio Characteristics................................................................................................................ 47

Chapter 5: Regulatory Information ...............................................................................48RegulatorWireless

CounFreq

Health anWarnPoteSafePaceOthe

RF ExposSafe

InternatioEurope ...US and CPower SuRadio FreRadio Fre

RadiCE MarkiStatemenWaste EleJapan (VC

ClassKorea WaOther Co

AustrBrazChileChinMexiSoutTaiw

Chapter 6: CRegistratiDocumenAltitude 4532 Series Access Point Installation Guide

y Information.............................................................................................................. 48Device Country Approvals.......................................................................................... 48try Selection .............................................................................................................. 49

uency of Operation FCC and IC.............................................................................. 49d Safety Recommendations ...................................................................................... 50ings for Use of Wireless Devices .............................................................................. 50

ntially Hazardous Atmospheres Fixed Installations................................................. 50ty in Hospitals............................................................................................................. 50makers....................................................................................................................... 50r Medical Devices....................................................................................................... 51ure Guidelines........................................................................................................... 51

ty Information ............................................................................................................. 51nal .............................................................................................................................. 51................................................................................................................................... 51anada ........................................................................................................................ 52pply............................................................................................................................ 52quency Interference Requirements FCC................................................................ 53quency Interference Requirements Canada ......................................................... 53

o Transmitters ............................................................................................................ 54ng and European Economic Area (EEA).................................................................... 54t of Compliance.......................................................................................................... 55ctrical and Electronic Equipment (WEEE) ................................................................ 55CI) - Voluntary Control Council for Interference....................................................... 57 B ITE ....................................................................................................................... 57rning Statement for Class B ITE ............................................................................... 57

untries ........................................................................................................................ 58alia............................................................................................................................. 58il.................................................................................................................................. 58.................................................................................................................................. 58

a ................................................................................................................................. 59co ............................................................................................................................... 59h Korea....................................................................................................................... 59an .............................................................................................................................. 60

ustomer Support .......................................................................................61on............................................................................................................................... 61tation.......................................................................................................................... 62

Altitu

CHA

Introduction

The AltitudeMobility SystController, enstandard Accwall and ceilthe placemenpoint on the ceiling tile to

The AltitudeCAT-5 or betEthernet conde 4532 Series Access Point Installation Guide5PTER1 4532 Access Point, a component of the Extreme Networks Wireless em, links wireless 802.11a/b/g/n devices to the Summit WM3000 Series abling growth of your wireless network with a cost effective alternative to ess Points. The Altitude 4532 Access Point provides two placement options: ing. Wall mount slots fit onto two provided screws. Arrows on the case guide t of the screws. For placement above a suspended ceiling, a safety wire tie case provides for a safety wire loop. The light pipe fits through a hole in the provide a view of the units status lights.

4532 Access Point receives all power and transfers data through the same ter Ethernet cable. There is no additional power supply required. An 802.3af troller or Power Injector is required.

Chapter 1: Introduction

6

Document ConventionsThe following graphical alerts are used in this document to indicate notable situations:

NOTE

Tips,

CAUTCare

WAR

Indica

Warnin

Read all iinstallatio

Remove je

Verify tha

Verify tha

Verify themeet equiAltitude 4532 Series Access Point Installation Guide

hints, or special requirements that you should take note of.

IONis required. Disregarding a caution can result in data loss or equipment malfunction.

NING!tes a condition or procedure that could result in personal injury or equipment damage.

gsnstallation instructions and site survey reports, and verify correct equipment n before connecting the Altitude 4532 Access Point.

welry and watches before installing this equipment.

t the unit is grounded before connecting it to the power source.

t any device connected to this unit is properly wired and grounded.

re is adequate ventilation around the device, and that ambient temperatures pment operation specifications.

Site Preparation

Altitude 453

Site Preparation Consult your site survey and network analysis reports to determine specific equipment

placement, power drops, and so on.

Assign in

Identify a

Ensure ad

Identify a

Verify thatransmiss

AltitudThe Altitudemodels. The antenna mod

External Altitude 4

Two wall

Two wall

Light pipe

Badge for

Altitude 4

Integrate Altitude 4

Two wall

Two wall

Altitude 42 Series Access Point Installation Guide7

stallation responsibility to the appropriate personnel.

nd document where all installed components are located.

equate, dust-free ventilation to all installed equipment.

nd prepare Ethernet and console port connections.

t cable lengths are within the maximum allowable distances for optimal signal ion.

e 4532 Access Point Package Contents 4532 Access Point is available in integrated antenna and external antenna contents of the package differ between the integrated antenna and external el.

Antenna Model Package Contents532 Access Point with external antenna connectors (Plenum Rated)

mount screws

anchors

light pipe

532 Access Point Installation Guide (This Guide)

d Antenna Model Package Contents532 Access Point with integrated antennas

mount screws

anchors

532 Access Point Installation Guide (This Guide)

Chapter 1: Introduction

8

Features One RJ-45 connector

LED indicators

Safety wir

Slots for w

Clips for

Lock port

The AltitudeEthernet por

NOTE

Whenfor Gigabit ope

The Altitude

The Access Pup or watchddownloaded Controller.Altitude 4532 Series Access Point Installation Guide

e tie point

all mounting

mounting on a suspended ceiling T-bar

for Kensington style Security Lock

4532 Access Point has one RJ-45 connector supporting an 10/100/1000 t and requires 802.3af-compliant power from an external source.

operating in a Gigabit Ethernet environment, CAT-5e or CAT-6 cable is recommended ration.

4532 Access Point comes with dual radios both supporting 802.11a/b/g/n.

oint contains runtime firmware which enables the unit to boot after a power og reset. The runtime firmware on the Access Point and the firmware from the controller can be updated via the Ethernet interface from the Wireless

Altitu

CHA

Hardware Installation

InstallaThe Altitudesuspended ce

To prepare fo

1 Match thelist and o

2 Verify thethe includ

SKUAP4532i-US

AP4532i-ROW

AP4532i-EU

Includes internal omni-directional antennas, Powered by 802.3af/at PoE or by use of a PoE injector.

AP4532e-US 15767 Altitude AP4regulatory doincluded-mude 4532 Series Access Point Installatio

802.3af/at PoEn Guide9

532e dual-radio Independent indoor Access Point for US main, 802.11a/b/g/n, 2x3 MIMO. External antennas not

st order separately up to 6 paddle antennas. Powered by or by use of a PoE injector.PTER2tion Instructions

4532 Access Point mounts either on a wall (with wide-shoulder screws) or on a iling T-bar. This unit is not designed for mounting on a desk.

r the installation, perform the following:

model number on the purchase order with the model numbers in the packing n the case of the device shipped.

contents of the box include the intended Altitude 4532 Access Point and that ed hardware matches the package contents on page 2.

Part Number Description15764 Altitude AP4532i dual-radio Independent indoor Access Point for US

regulatory domain, 802.11a/b/g/n, 2x3 MIMO, Includes internal omnidirectional antennas, Powered by 802.3af/at PoE or by use of a PoE injector.

15765 Altitude AP4532i dual-radio Independent indoor Access Point for the Rest of the World regulatory domain, 802.11a/b/g/n, 2x3 MIMO, Includes internal omni-directional antennas, Powered by 802.3af/at PoE or by use of a PoE injector.

15798 Altitude AP4532i dual-radio Independent indoor Access Point for the European Union regulatory domain, 802.11a/b/g/n, 2x3 MIMO,

Precautions

Altitude 453

NOTE

In therepresents the

3 Review siposition f

4 Connect athe cable the install

NOTE

Whenfor Gigabit ope

PrecauBefore install

Extreme Nwet or du

Verify tha

AP4532e-ROW 15768 Altitude AP4532e dual-radio Independent indoor Access Point for the Rest of the World regulatory domain, 802.11a/b/g/n, 2x3 MIMO.

AP4532e-EU

SKUPart Number Description2 Series Access Point Installation Guide10

above SKU numbers, "US" represents the United States regulatory model, and "ROW" Rest of World regulatory model.

te survey and network analysis reports to determine the location and mounting or the Altitude 4532 Access Point.

CAT-5 or better Ethernet cable to a compatible 802.3af power source and run to the installation site. Ensure there is sufficient slack on the cable to perform ation steps.

operating in a Gigabit Ethernet environment, CAT-5e or CAT-6 cable is recommended ration.

tionsing an Altitude 4532 Access Point, verify the following:

etworks recommends that you do not install the Altitude 4532 Access Point in sty areas.

t the environment has a continuous temperature range between 0 C to 50 C.

External antennas not included-must order separately up to 6 paddle antennas. Powered by 802.3af/at PoE or by use of a PoE injector.

15799 Altitude AP4532e dual-radio Independent indoor Access Point for the European Union regulatory domain, 802.11a/b/g/n, 2x3 MIMO. External antennas not included-must order separately up to 6 paddle antennas. Powered by 802.3af/at PoE or by use of a PoE injector.

Access Point Placement

Altitude 453

Access Point PlacementFor optimal performance, install the Access Point away from transformers, heavy-duty motors, fluorescent lights, microwave ovens, refrigerators, and other industrial equipment. Signal loss caAccess Point

Antenna covnot bright enUniform anteefficient cove

Place the Acc

Install the

Orient the

To maximizeconducting ainstalling the

IntegraInstrucThis mountinusing the twmounted ontThe followin

Wall Mo Two wide

Two wall

Security c2 Series Access Point Installation Guide11

n occur when metal, concrete, walls, or floors block transmission. Install the in an open area or add Access Points as needed to improve coverage.

erage is analogous to lighting. Users might find an area lit from far away to be ough. An area lit sharply might minimize coverage and create dark areas. nna placement in an area (like even placement of a light bulb) provides even, rage.

ess Point using the following guidelines:

Access Point at an ideal height of 10 feet from the ground.

Access Point antennas vertically for best reception.

the Access Points radio coverage area, Extreme Networks recommends site survey to define and document radio interference obstacles before Access Point.

ted Antenna Model Wall Mount tionsg requires hanging the Altitude 4532 Access Point along its width or length

o slots on the bottom of the unit. The Altitude 4532 Access Point can be o any plaster, wood, or cement wall surface using the provided wall anchors. g illustration displays a lengthwise mount.

unt Hardware-shoulder Phillips pan head self-tapping screws

anchors

able (optional)

Integrated Antenna Model Wall Mount Instructions

Altitude 453

NOTE

In the event that the original mounting screws are lost, the following screws can be used instead: (ANSI Standard) #6-18 X 0.875in. Type A or AB Self-Tapping Screw, or (ANSI Standard Metric) M3.5 X2 Series Access Point Installation Guide12

0.6 X 20mm Type D Self-Tapping Screw.


Altitude 453

Wall Mount Procedure

1 Orient the2 Series Access Point Installation Guide13

case on the wall by its width or length.

Integrated Antenna Wall Mount


Altitude 453

CAUTIONTo ensure proper operation of the Altitude 4532 Access Point, ensure that it is mounted

with the logo facing upwards.

2 Using themounting

3 At each pmounting

NOWh

going direc

4 If required

5 Attach thepower sou

6 Place the

7 Slide the heads.

8 Verify tha2 Series Access Point Installation Guide14

arrows on one edge of the case as guides, move the edge to the midline of the area and mark points on the midline for the screws.

oint, drill a hole in the wall, insert an anchor, screw into the anchor the wall screw and stop when there is 1mm between the screw head and the wall.

TE

en pre-drilling a hole, the recommended hole size is 2.8mm (0.11in.) if the screws are tly into the wall and 6mm (0.23in.) if the provided wall anchors are being used.

, install and attach a security cable to the units lock port.

Ethernet cable to the unit and to a controller with an 802.3af-compatible rce.

middle of each of the cases mount slots over the screw heads.

case down along the mounting surface to hang the mount slots on the screw

t the unit has power by observing that the LEDs are lit or flashing.

Integrated Antenna Model Suspended Ceiling T-Bar Mount Instructions

Altitude 453

Integrated Antenna Model Suspended CeilingT-Bar Mount InstructionsCeiling mounsuspended ce

Suspend

1 If required

2 Plug the Epower sou

3 Align the

4 Orient the

5 Rotate the

6 Push the

7 Rotate the

8 Verify the2 Series Access Point Installation Guide15

t requires holding the Altitude 4532 Access Point up against a T-bar of a iling grid and twisting the case onto the T-bar.

ed Ceiling Mount Procedure


thernet cable into the unit and to a controller with an 802.3af compatible rce.

bottom of the T-bar with the back of the case.

case by its length, and the length of the T-bar.

case 45 degrees clockwise, or about 10 oclock.

back of the case onto the bottom of the T-bar.

case 45 degrees counter-clockwise. The clips click as they fasten to the T-bar.

unit has power by observing the LEDs.

External Antenna Model Wall Mount Instructions

Altitude 453

External Antenna Model Wall Mount InstructionsWall mountinusing the paimounted ont

Wall Mo Two wide

Two wall

Safety wir

NOTE

In the(ANSI StandarX 0.6 X 20mm2 Series Access Point Installation Guide16

g requires hanging the Altitude 4532 Access Point along its width or length r of slots on the bottom of the unit. The Altitude 4532 Access Point can be o any plaster, wood, or cement wall surface using the provided wall anchors.

unt Hardware-shoulder Phillips pan head self-tapping screws

anchors

e (recommended) and security cable (optional)

event that the original mounting screws are lost, the following screws can be used: d) #6-18 X 0.875in. Type A or AB Self-Tapping Screw, or (ANSI Standard Metric) M3.5 Type D Self-Tapping Screw.

External Antenna Model Wall Mount Instructions

Altitude 453

Wall Mount Procedure

1 Orient the

2 Using themounting

3 At each pmounting

NOTE

The rand 6mm (0.2

4 If requiredaround th2 Series Access Point Installation Guide17

case on the wall by its width or length.

arrows on one edge of the case as guides, move the edge to the midline of the area and mark points on the midline for the screws.

oint, drill a hole in the wall, insert an anchor, screw into the anchor the wall screw and stop when there is 1mm between the screw head and the wall.

ecommended hole size is 2.8mm (0.11in.) if the screws are going directly into the wall, 3in.) if the provided wall anchors are being used.

, loop a safety wire, between 1.5mm (.06in.) and 2.5mm (.10in.) in diameter, e tie post and secure the loop.

External Antenna Model Suspended Ceiling Tile (Plenum) Mount Instructions

Altitude 453

5 If required, install and attach a security cable to the units lock port.

6 Place the large corner of each of the cases mount slots over the screw heads.

7 Slide the case down along the mounting surface to hang the mount slots on the screw heads.

8 Attach ap

9 Attach thepower sou

10 Verify the

Externa(PlenumCeiling mounand installing

NOTE

Notesplaced on sus

CAUTExtre

any suspendean unsupporteAltitude 4532 Ashould be a st2.5mm (.10in.)

This placemeof the unit.2 Series Access Point Installation Guide18

propriate antennas to the connectors.

Ethernet cable to the unit and to a controller with an 802.3af compatible rce.

unit has power by observing that the LEDs are lit or flashing.

l Antenna Model Suspended Ceiling Tile ) Mount Instructions

t requires placing the Altitude 4532 Access Point above a suspended ceiling the provided light pipe for viewing the status lights of the unit.

or warnings about suspended ceiling mounts apply to all installations where the unit is pended ceiling tile. The case has a safety wire tie point for a standard safety wire.

IONme Networks does not recommend mounting the Altitude 4532 Access Point directly to d ceiling tile with a thickness less than 12.7mm (0.5in.) or a suspended ceiling tile with d span greater than 660mm (26in.). Extreme Networks strongly recommends fitting the ccess Point with a safety wire suitable for the specific installation. The safety wire

andard ceiling suspension cable or equivalent steel wire between 1.59mm (.062in.) and in diameter.

nt requires installation of the provided light pipe for viewing the status lights

External Antenna Model Suspended Ceiling Tile (Plenum) Mount Instructions

Altitude 453

Suspended Ceiling Mount Hardware Light pipe

Badge for light pipe

Safety wir

Ceiling M

1 If possiblework surf

2 If requiredin the ceil

3 If required

4 Mark a po

5 Push the use a dril

6 Attach ap

7 Snap the

8 Fit the lig

9 Attach anport.

10 Bring the 2 Series Access Point Installation Guide19

e (recommended) and security cable (optional)

ount Procedure

, remove the ceiling tile from its frame and place it, finished side down, on a ace.

, install a safety wire, between 1.5mm (.06in.) and 2.5mm (.10in.) in diameter, ing space.


int on the upper or unfinished side of the tile.

light pipe through the tile at the mark and remove the light pipe. If necessary, l to make a hole in the tile.

propriate antennas to the connectors.

clips of the light pipe into the bottom of the case.

ht pipe into hole in the tile from its unfinished side.

y safety wire to the safety wire tie point or security cable to the units lock

tile into the ceiling space.

Badge

Ceiling Tile

Light Pipe

Antenna Options for Altitude 4532 Access Point External Antenna

Altitude 453

11 Plug the Ethernet cable into the unit and to a controller with an 802.3af compatible power source.

12 Verify the unit has power by observing the LEDs.

13 Place the ceiling tile back in its frame.

14 Snap the

AntennExternaExtreme NetwAntenna modenvironment

For a more eAccess PointEnterprise Wihttp://www.extre2 Series Access Point Installation Guide20

badge onto the light pipe from the finished side of the tile.

a Options for Altitude 4532 Access Point l Antennaorks supports various antennas for Altitude 4532 Access Point External

els. Select an antenna model best suited for the intended operational of your Access Point.

xhaustive overview of the antennas supported by the Extreme Networks family, refer to the Enterprise Wireless LAN Antenna Specification Guide and reless LAN Antenna Specification Guide Addendum documents available frommenetworks.com/go/documentation.

LED Indicators

Altitude 453

LED IndicatorsBoth Integrated Antenna and External Antenna models have LED activity indicators on the front of the case. With the External Antenna models mounted above a ceiling, LEDs are at the center of through the c

The LEDs practivity for th

TaskSystem Bootin

Radio ShutdowAdministrativeor LEDs Disabled

Radio Not ConfiguredorCountry-code setorWLAN not mato radio

Locate AP Mo2 Series Access Point Installation Guide21

an oval badge on the ceiling; a light pipe enables viewing the back LEDs eiling tile.

ovide a status display indicating error conditions, transmission, and network e 5 GHz 802.11a/n (amber) radio or the 2.4 GHz 802.11b/g/n (green) radio.

5 GHz Activity LED (Amber) 2.4 GHz Activity LED (Green)g Solid On (During start up only) Solid On (During start up only)

n ly

Off Off

not

pped

Blink (On 2 seconds, Off 2 seconds) Blink (On 2 seconds, Off 2 seconds)

de Off Blinking

Altitu

CHA

Defining A Basic

An Altitude of initially acoperational m

Using tOnce the Altsteps to get t

1 The Accesaddress calast two oAccess Po

For exam

MAC addZero-conf

To derive

a Open Calcula

b With t

c Enter a hex byte of the Access Points MAC address. For example, F0.

d Select the Dec radio button. The for the last Access Point MAC adde 4532 Series Access Point Installation Guide22

calculator converts F0 into 240. Repeat this process dress octet.PTER3 Configuration4532 Access Point can utilize an initial setup wizard to streamline the process cessing the wireless network. The wizard defines the Access Points ode, deployment location, basic security, network, and WLAN settings.

he Initial Setup Wizarditude 4532 Access Point is installed and powered on, complete the following he Access Point up and running and access management functions:

s Points IP address is optimally provided using DHCP. A zero config IP n also be derived if DHCP resources are unavailable. Using zero config, the

ctets in the IP address are the decimal equivalent of the last two bytes in the ints hardcoded MAC address.

ple:

ress - 00:C0:23:00:F0:0A ig IP address - 169.254.240.10

the Access Points IP address using its MAC address:

the Windows calculator be selecting Start > All Programs > Accessories > tor. This menu path may vary depending on your version of Windows.

he Calculator displayed, select View > Scientific. Select the Hex radio button.

Using the Initial Setup Wizard

Altitude 453

2 Point the Web browser to the Access Points IP address. The following login screen displays:

3 Enter the

4 Enter the

5 Click the

NOWh

device sec

NOIf y

Points actu2 Series Access Point Installation Guide23

default username admin in the Username field.

default password admin123 in the Password field.

Login button to load the management interface.

TE

en logging in for the first time, you are prompted to change the password to enhance urity in subsequent logins.

TE

ou get disconnected while running the wizard, you can connect again with the Access al IP address (once obtained) and resume the wizard.


Altitude 453

6 If this is the first time the management interface has been accessed, a dialogue displays to start the wizard. Select Start Wizard to run the initial setup wizard.2 Series Access Point Installation Guide24


Altitude 453

The first page of the Initial AP Setup Wizard displays the Navigation Panel and Introduction for the configuration activities comprising the Access Point's initial setup.

A green cas havingthe task a2 Series Access Point Installation Guide25

heckmark to the left of an item in the Navigation Panel defines the listed task its minimum required configuration parameters set correctly. A red X defines s still requiring at least one parameter be defined correctly.


Altitude 453

The Introduction screen displays a list of the basic configuration activities supported by the Initial Setup Wizard.

7 Select SavconfiguraSelect Bacupdates.

NOWh

Initial AP S2 Series Access Point Installation Guide26

e/Commit within each page to save the updates made to that page's tion. Select Next to proceed to the next page listed in the Navigation Panel. k to revert to the previous screen in the Navigation Panel without saving your

TE

ile you can navigate to any page in the navigation panel, you cannot complete the etup Wizard until each task in the Navigation Panel has a green checkmark.


Altitude 453

8 Select Next. The Initial AP Setup Wizard displays the Access Point Type screen to define the Access Point's Standalone versus Virtual Controller AP functionality and the way the Access Point is adopted to a controller.2 Series Access Point Installation Guide27


Altitude 453

9 Select an Access Point Type from the following options:

Virtual Controller AP - When more than one Access Point is deployed, a single Access Point can function as a Virtual Controller AP. Up to 24 Access Points can be connected to, and managed by, a single Virtual Controller AP of the same Altitude 4532 A

StandaAccessby a R

NOIf d

Access Poprovides thinterfaces cproblems.

AdoptecontroInitial profileoverw2 Series Access Point Installation Guide28

ccess Point model.

lone AP -Select this option to deploy this Access Point as an autonomous fat Point. A Standalone AP isn't managed by a Virtual Controller AP, or adopted FS series controller.

TE

esignating the Access Point as a Standalone AP, Extreme Networks recommends the ints UI be used exclusively to define its device configuration, and not the CLI. The CLI e ability to define more than one profile and the UI does not. Consequently, the two annot be used collectively to manage profiles without an administrator encountering

d to Controller - Select this option when deploying the Access Point as a ller managed (Dependent mode) Access Point. Selecting this option closes the AP Setup Wizard. An adopted Access Point obtains its configuration from a stored on its managing controller. Any manual configuration changes are ritten by the controller upon reboot.


Altitude 453

Select the Automatic controller discovery option to enable the Access Point to be discovered and adopted using layer 2 settings. If preferring layer 3 adoption, select the Static Controller Configuration option, and define the addresses of the preferred controllers. If using the static method, youll also need to define whether the Access Point r2 Series Access Point Installation Guide29

eceives an IP address using DHCP or if IP resources are provided statically.


Altitude 453

10 Select Next. The Initial AP Setup Wizard displays the Access Point Mode screen to define the Access Point's routing or bridging mode functionality.2 Series Access Point Installation Guide30


Altitude 453

11 Select an Access Point Mode from the available options.

Router Mode - In Router Mode, the Access Point routes traffic between the local network (LAN) and the Internet or external network (WAN). Router mode is recommended in a deployment supported by just a single Access Point.

Bridge and WtypicalAccessradio b2 Series Access Point Installation Guide31

Mode - In Bridge Mode, the AP depends on an external router for routing LAN AN traffic. Routing is generally used on one device, whereas bridging is ly used in a larger network. Thus, select Bridge Mode when deploying this Point with numerous peer APs supporting clients on both the 2.4 and 5GHz ands.


Altitude 453

12 Select Next. The Initial AP Setup Wizard displays the LAN Configuration screen to set the Access Point's LAN interface configuration. 2 Series Access Point Installation Guide32


Altitude 453

13 Set the following DHCP and Static IP Address/Subnet information for the LAN interface:

Use DHCP - Select the checkbox to enable an automatic network address configuration using the Access Points DHCP server.

Static ILAN ioptionas thos

- Usecheinfo

- RanAccandreq

- Defgat

DNS Finto IPresourname corresp

- PrimDN

- Secpro2 Series Access Point Installation Guide33

P Address/Subnet - Enter an IP Address and a subnet for the Access Point's nterface. If Use DHCP is selected, this field is not available. When selecting this , define the following DHCP Server and Domain Name Server (DNS) resources, e fields will become enabled on the bottom portion of the screen.

on-board DHCP server to assign IP addresses to wireless clients - Select the ckbox to enable the Access Points DHCP server to provide IP and DNS rmation to clients on the LAN interface.

ge - Enter a starting and ending IP Address range for client assignments on the ess Point's LAN interface. Avoid assigning IP addresses from x.x.x.1 - x.x.x.10 x.x.x.255, as they are often reserved for standard network services. This is a

uired parameter.

ault Gateway - Define a default gateway address for use with the default eway. This is a required parameter.

orwarding - Select this option to allow a DNS server to translate domain names addresses. If this option is not selected, a primary and secondary DNS ce must be specified. DNS forwarding is useful when a request for a domain is made but the DNS server, responsible for converting the name into its

onding IP address, cannot locate the matching IP address.

ary DNS - Enter an IP Address for the main Domain Name Server providing S services for the Access Point's LAN interface.

ondary DNS - Enter an IP Address for the backup Domain Name Server viding DNS services for the Access Point's LAN interface


Altitude 453

14 Select Next. The Initial AP Setup Wizard displays the WAN Configuration screen to set the Access Point's WAN interface configuration.2 Series Access Point Installation Guide34


Altitude 453

15 Set the following DHCP and Static IP Address/Subnet information for the WAN interface:

Use DHCP - Select the checkbox to enable an automatic network address configuration using the Access Points DHCP server.

Static IPoint's

The poconnecAccessoption

Enablethe Ac

16 Select Nexsupport foas a dedic2 Series Access Point Installation Guide35

P Address/Subnet - Enter an IP Address/Subnet and gateway for the Access WAN interface. These are required fields

rt connected to the WAN - Select the port used as the physical Access Point tion to the external network. The ports available differ depending on the Point model deployed. Access point models with a single port have this fixed.

NAT on the WAN Interface - Select the checkbox to allow traffic to pass between cess Point's WAN and LAN interfaces.

t. The Initial AP Setup Wizard displays the Radio Configuration screen to define r the 2.4GHz radio band, 5GHz radio band or to set the radio's functionality ated sensor. An Altitude 4532 Access Point supports a single dual-band radio.


Altitude 453

NOTEThe ADSP Sensor Support field displays at the bottom of the screen only if a radio has

been dedicated as a sensor.

17 Set the fo

Configusuppo

- Radthecliesup802

- Powto asett

- Cha802in teacSelefor thetheWhnetAccinit

ConfiguexcluschanneAccessand se

Disableeither netwo2 Series Access Point Installation Guide36

llowing parameters for the radio:

re as a Data Radio - Select this option to dedicate this radio for WLAN client rt in either the selected 2.4 or 5GHz radio band.

io Frequency Band - Select either the 2.4GHz or 5.0GHz radio band to use with radio when selected as a Data Radio. The selected band is used for WLAN nt support. Considers selecting one radio for 2.4GHz and another for 5GHz port (if using a dual or three radio model) when supporting clients in both the .11bg and 802.11n bands.

er Level - Use the spinner control to select a 1 - 23 dBm minimum power level ssign to this radio in selected 2.4 or 5.0 GHz band. 1 dBm is the default ing.

nnel Mode - Select either Random, Best or Static. Select Random for use with a .11a/n radio. To comply with Dynamic Frequency Selection (DFS) requirements he European Union, the 802.11a/n radio uses a randomly selected channel h time the Access Point is powered on. ct Best to enable the Access Point to scan non-overlapping channels and listen beacons from other Access Points. After the channels are scanned, it will select channel with the fewest Access Points. In the case of multiple Access Points on same channel, it will select the channel with the lowest average power level. en Constantly Monitor is selected, the Access Point will continuously scan the work for excessive noise and sources of interference. Select Static to assign the ess Point a permanent channel and scan for noise and interference only when ialized.

re as a Sensor Radio - Select this option to dedicate the radio to sensor support ively. When functioning as a sensor, the radio scans in sensor mode across all ls within the 2.4 and 5.0GHz bands to identify potential threats within the Point managed network. If dedicating a radio as a sensor resource, a primary condary ADSP server must be specified as an ADSP management resource.

the Radio - Select this option to disable this radio, thus prohibiting it from providing WLAN or sensor support. Verify this course action with your rk administrator before rendering the radio offline.


Altitude 453

NOTEIf configuring an Altitude 4532 Access Point as a sensor, the Access Point will require a

reboot before its sensor functionality is invoked. The reboot can take place at the completion of the Initial AP S2 Series Access Point Installation Guide37

etup Wizard.


Altitude 453

18 Select Next. The Initial AP Setup Wizard displays the Wireless LAN Setting screen to define network address and security settings for two WLAN configurations available to the Access Point as part of the Initial AP Setup Wizard. Once the Access Point has an initial configuration defined, numerous additional WLAN configurations can be set.2 Series Access Point Installation Guide38


Altitude 453

19 Set the following parameters for each of the two WLAN configurations available as part of this Initial AP Setup Wizard:

SSID - Enter or modify the Services Set Identification (SSID) associated with the WLAN. The WLAN name is auto-generated using the SSID until changed by the user. Trequire

WLANthe WL

- No bet

- CappaggraRA

- PSKshaclie(8-6

- EAwitthisuse

WPA Kenter aprimaralphanfrom e

RADIUcredenresourRADIUsecret 2 Series Access Point Installation Guide39

he maximum number of characters is 32. Do not use < > | & \ ? , This is a d parameter for each WLAN.

Type - Set the data protection scheme used by clients and Access Points within AN. The following options are available:

Authentication and no Encryption - Select this option to provide no security ween the Access Point and connected clients on this WLAN.

tive Portal Authentication and No Encryption - Select this option to use a Web e (either internally or externally hosted) to authenticate users before access is nted to the network. If using this option, define whether a local or external DIUS authentication resource is used.

Authentication and WPA2 Encryption - Select the option to implement a pre-red key that must be correctly shared between the Access Point and requesting nts using this WLAN. If using this option, specify a WPA key in either ASCII 3 characters) or HEX (64 characters) format.

P Authentication and WPA2 Encryption - Select this option to authenticate clients hin this WLAN through the exchange and verification of certificates. If using option, define whether a local or external RADIUS authentication resource is d.

ey - If a WPA key is required (PSK Authentication and WPA2 Encryption), n alphanumeric string of 8 to 63 ASCII characters or 64 HEX characters as the y string both transmitting and receiving authenticators must share. The umeric string allows character spaces. This passphrase saves the administrator ntering the 256-bit key each time keys are generated.

S Server - If the WLAN type requires a RADIUS server to validate user tials, designate whether the Access Point is using an External RADIUS Server ce or the Access Point's own Onboard RADIUS Server. If using an external

S server resource, provide the IP address of the external server and the shared used to authenticate the request.


Altitude 453

NOTEIf using the Access Points onboard RADIUS server, an additional RADIUS Server

Configuration screen displays within the Navigation Panel on the left-hand side of the screen. Use this screenconnection

20 Select Nexif the Acconboard RCountry/Dtime infor2 Series Access Point Installation Guide40

to create user accounts validated when the Access Point authenticates client requests to the onboard RADIUS server.

t. The Initial AP Setup Wizard displays the RADIUS Server Configuration screen ess Points onboard RADIUS server is required to validate user requests. If an ADIUS server is not required, the Initial AP Setup Wizard displays the ate/Time screen to set device deployment, administrative contact and system mation.


Altitude 453

21 Refer to the Username, Password, Description and Actions columns to review credentials of existing RADIUS Server user accounts. Add new accounts or edit the properties of existing accounts as updates are required.

22 Refer to the Add On-Board RADIUS Server Users field to set the following parameters for a user acc

Usernalengthrequire

Passwoeach tiAccess

Confirmpassw

Descripfurther

23 When commodified Reset clea2 Series Access Point Installation Guide41

ount:

me - If adding a new user account, create a username up to X characters in . The username cannot be revised if modifying the user configuration. This is a d parameter.

rd - Provide (or modify) a password between X - X characters in length entered me a requesting client attempts access to the AP managed network using the Point's onboard RADIUS server. This is a required parameter.

Password - Re-enter (or modify) the password as a means of confirming the ord. This is a required parameter.

tion - Optionally provide a description of the user account as a means of differentiating it from others.

pleted, select Add User to commit a new user, Modify User to commit a user or Reset to clear the screen without updating the configuration. Selecting rs the field of all entered user account information.


Altitude 453

24 Select Next. The Initial AP Setup Wizard displays the Country/Date/Time screen to set device deployment, administrative contact and system time information. The system time can either be set manually or be supplied by a dedicated Network Time Protocol (NTP) resource.2 Series Access Point Installation Guide42


Altitude 453

25 Refer to the Country and Time Zone field to set the following device deployment information:

Location - Define the location of the Access Point. The Location parameter acts as a reminder of where the AP can be located within the Extreme Networks managed wirele

Contacprovid

CountrprompdisplaySelectiregulasignal

Time Zparamcountr

26 If an NTPAM/PM

27 OptionallPoint. Onengaged a

28 If an NTPAM/PM

29 OptionallPoint. Onengaged a

30 Select Nexsummariz2 Series Access Point Installation Guide43

ss network.

t - Specify the contact information for the administrator. The credentials ed should accurately reflect the individual responding to service queries.

y - Select the Country where the Access Point is deployed. The Access Point ts for the correct country code on the first login. A warning message also s stating an incorrect country setting may result in illegal radio operation.

ng the correct country is central to legal operation. Each country has its own tory restrictions concerning electromagnetic emissions and the maximum RF strength that can be transmitted. This is a required parameter.

one - Set the time zone where the Access Point is deployed. This is a required eter. The setting should be complimentary with the selected deployment y.

resource is unavailable, set the System Date and Time (calendar date, time and designation).

y enter the IP address of a server used to provide system time to the Access ce the IP address is entered, the Network Time Protocol (NTP) functionality is utomatically for synchronization with the NTP resource.

resource is unavailable, set the System Date and Time (calendar date, time and designation).

y enter the IP address of a server used to provide system time to the Access ce the IP address is entered, the Network Time Protocol (NTP) functionality is utomatically for synchronization with the NTP resource.

t. The Initial AP Setup Wizard displays the Summary and Commit screen to e the screens (pages) and settings updated using the Initial AP Setup Wizard.


Altitude 453

There's no user intervention or additional settings required within this screen. Its an additional means of validating the configuration before its deployed. However, if a screen displays settings not intended as part of the initial configuration, the screen can be selected from within the Navigation Panel and its settings modified accordingly.

31 If the conthese settibased on the Back a2 Series Access Point Installation Guide44

figuration displays as intended, select the Save/Commit button to implement ngs to the Access Points configuration. If additional changes are warranted the summary, either select the target page from the Navigational Panel, or use nd Next buttons to scroll to the target screen.

Altitu

CHA

Specifications

AltitudModel An Altitude electrical cha

AltitudModel An Altitude physical char

Operating Cur

Dimensions

HousingWeightOperating TemStorage TempOperating Humidity 5 to 95% Relative Humidity non-condensingStorage Humidity 85% Relative Humidity non-condensingOperating Altitude (max) 8,000 ft @ StoraElectde 4532 Series Access Point Installatio

ge Altitude (max) 30,000 ft @ 1rostatic Discharge +/-15kV Air ann Guide45

28C2Cd +/-8kV Contact @ 50% Relative HumidityPTER4e 4532 Access Point External Antenna Electrical Characteristics4532 Access Point External Antenna model Access Point has the following racteristics:

e 4532 Access Point External Antenna Physical Characteristics4532 Access Point External Antenna model Access Point has the following acteristics:

rent & Voltage 180ma- 270ma @ 48VDC using Power over Ethernet

8.50 in. Depth x 5.5 in. Width x 1.5 in. Height21.59 cm Depth x 13.97 cm Width x 3.81 cm Height Metal2.5 lbs / 1.13 kg

perature 32F to 122F/0C to 50Cerature -40F to 158F/-40C to 70C

Altitude 4532 Access Point Integrated Antenna Model Electrical Characteristics

Altitude 453

Altitude 4532 Access Point Integrated Antenna Model Electrical CharacteristicsAn Altitude characteristic

AltitudModel An Altitude physical char

Operating Cur& Voltage

Dimensions

HousingWeightOperating TemStorage TempOperating HumStorage HumidOperating AltitStorage AltitudElectrostatic D2 Series Access Point Installation Guide46

4532 Access Point Integrated model Access Point has the following electrical s:

e 4532 Access Point Integrated Antenna Physical Characteristics4532 Access Point Integrated Antenna model Access Point has the following acteristics:

rent 180ma- 270ma @ 48VDC using Power over Ethernet

9.50 in. Depth x 7.5 in. Width x 1.9 in. Height24.13 cm Depth x 19.05 cm Width x 4.83 cm HeightPlastic2.0 lbs / 0.91 kg

perature 32F to 122F/0C to 50Cerature -40F to 158F/-40C to 70Cidity 5 to 95% Relative Humidity non-condensingity 85% Relative Humidity non-condensing

ude (max) 8,000 ft @ 28Ce (max) 30,000 ft @ 12Cischarge +/-15kV Air and +/-8kV Contact @ 50% Relative Humidity

Radio Characteristics

Altitude 453

Radio CharacteristicsThe Altitude 4532 Access Point model Access Points have the following radio characteristics:

Operating Channels

Data Rates Supported

Wireless Medi

Network StandMaximum AvaTransmit Powe

Transmit PoweAdjustmentAntenna Configuration2 Series Access Point Installation Guide47

All channels from 4920 MHz to 5825 MHz except channel 52 -64Channels 1-13 (2412-2472 MHz)Channel 14 (2484 MHz) Japan onlyActual operating frequencies depend on regulatory approval for the country of use.802.11b: 1,2,5.5,11Mbps802.11g: 1,2,5.5,11,6,9,12,18,24,36,48, and 54Mbps802.11a: 6,9,12,18,24,36,48, and 54Mbps802.11n: MCS 0-15 up to 300Mbps

um Direct Sequence Spread Spectrum (DSSS),Orthogonal Frequency Division Multiplexing (OFDM)Spatial multiplexing (MIMO)

ards 802.11a, 802.11b, 802.11g, 802.3, 802.11n (Draft 2.0)ilable r

Maximum available conducted transmit power per chain: 2.4 GHz: 21dBmMaximum available conducted transmit power all chains: 2.4 GHz: 24dBmMaximum available conducted transmit power per chain: 5 GHz: 19dBmMaximum available conducted transmit power all chains: 5 GHz: 22dBm

r 1dB increments

2x3 MIMO (transmit on two and receive on all threeantennas)

Altitu

CHA

Regulatory Information

RegulaThis device iInc. is a who

This guide ap

All Extreme locations the

Any changesExtreme Netw

Extreme Netwwill not exce

Antennas: Usantennas, mo

This device i

WirelesRegulatory markings, subject to certificradio(s) is/are approved for use in theChinde 4532 Series Access Point Installatio

a, S. Korea, Australia, and Europe. n Guide48

ation, are applied to the device signifying the following countries: United States, Canada, Japan, PTER5tory Information

s approved under the Symbol Technologies, Inc. brand: Symbol Technologies, lly owned subsidiary of Motorola Solutions, Inc. (collectively "Motorola").

plies to Model Number AP-0650

Networks devices are designed to be compliant with rules and regulations in y are sold and will be labeled as required.

or modifications to Extreme Networks equipment, not expressly approved by orks, could void the users authority to operate the equipment.

orks devices are professionally installed, the Radio Frequency Output Power ed the maximum allowable limit for the country of operation.

e only the supplied or an approved replacement antenna. Unauthorized difications, or attachments could cause damage and may violate regulations.

s only to be used with an Extreme Networks Wireless Controller.

s Device Country Approvals

Wireless Device Country Approvals

Altitude 453

Please refer to the Declaration of Conformity (DoC) for details of other country markings. This is available at http://www.extremenetworks.com/go/rfcertification.htm.

Note: For 2.4GHz or 5GHz Products: Europe includes, Austria, Belgium, Bulgaria, Czech Republic, Cyprus, Denmark, Estonia, FinlFor 2.4GHz or 5GHz Products: Europe includes, Austria, BelgGermany, GrLuxembourgSlovenia, Spa

Oper

CountrySelect only thoperation of

Frequen

5 GHz OnlThe use in thMHz) is restrillegal.

Industry CCaution: Thepotential for radars are all5650-5850 MHdevices.

Avertissemenuniquement prjudiciable2 Series Access Point Installation Guide49

ium, Bulgaria, Czech Republic, Cyprus, Denmark, Estonia, Finland, France, eece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, , Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic, in, Sweden, Switzerland and the United Kingdom.

ation of the device without regulatory approval is illegal.

Selection e country in which you are using the device. Any other selection will make the this device illegal.

cy of Operation FCC and IC

ye UNII (Unlicensed National Information Infrastructure) band 1 (5150-5250 icted to Indoor Use Only; any other use will make the operation of this device

anada Statement: device for the band 5150-5250 MHz is only for indoor usage to reduce harmful interference to co-Channel mobile satellite systems. High power ocated as primary users (meaning they have priority) of 5250-5350 MHz and

z and these radars could cause interference and/or damage to LE-LAN

t: Le dispositive fonctionnant dans la bande 5150-5250 MHz est rserv pour une utilisation l'intrieur afin de rduire les risques de brouillage aux systmes de satellites mobiles utilisant les mmes canaux.

Health and Safety Recommendations

Altitude 453

Les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d., qu'ils ont la priorit) pour les bands 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.

Health

Wa Plea

PotentiaYou are remidepots, chemgrain, dust, o

Safety inWirelequipthe ad

PacemaPacemaker mbetween a hathe pacemakrecommenda

Persons with

Should Aturned ON

Should no2 Series Access Point Installation Guide50

and Safety Recommendations

rnings for Use of Wireless Devicesse observe all warning notices with regard to the usage of wireless devices.

lly Hazardous Atmospheres Fixed Installationsnded of the need to observe restrictions on the use of radio devices in fuel ical plants etc. and areas where the air contains chemicals or particles (such as r metal powders).

Hospitalsess devices transmit radio frequency energy and may affect medical electrical ment. When installed adjacent to other equipment, it is advised to verify that jacent equipment is not adversely affected.

kersanufacturers recommended that a minimum of 15cm (6 inches) be maintained ndheld wireless device and a pacemaker to avoid potential interference with

er. These recommendations are consistent with independent research and tions by Wireless Technology Research.

Pacemakers:

LWAYS keep the device more than 15cm (6 inches) from their pacemaker when .

t carry the device in a breast pocket.

RF Exposure Guidelines

Altitude 453

Should use the ear furthest from the pacemaker to minimize the potential for interference.

If you have any reason to suspect that interference is taking place, turn OFF your device.

Other MPlease consuoperation of

RF

Safety In

Reducing Only operate

InternaThe device coelectromagneexposure to e(DoC) at http

Europe

Remote anTo comply wremote locatimust operate2 Series Access Point Installation Guide51

edical Deviceslt your physician or the manufacturer of the medical device, to determine if the your wireless product may interfere with the medical device.

Exposure Guidelines

formation

RF ExposureUse Properly the device in accordance with the instructions supplied.

tionalmplies with internationally recognized standards covering human exposure to tic fields from radio devices. For information on International human letromagnic fields refer to the Extreme Networks Declaration of Conformity ://www.extremenetworks.com/go/rfcertification.htm.

d Standalone Antenna Configurationsith EU RF exposure requirements, antennas that are mounted externally at ons or operating near users at stand-alone desktop of similar configurations with a minimum separation distance of 20 cm from all persons.

US and Canada

Altitude 453

US and Canada

Co-located statementTo comply wtransmitter mantenna exce

Radiation Ex

This equipmenvironment20cm betwee

NOTE IMPO

Dclaration d

Cet quipemun environneminimum de

Remote anTo comply wremote locatimust operate

To satisfy FCminimum se

Power This device cappropriate a2 Series Access Point Installation Guide52

ith FCC RF exposure compliance requirement, the antenna used for this ust not be co-located or operating in conjunction with any other transmitter/

pt those already approved in this filling.

posure Statement:

ent complies with IC radiation exposure limits set forth foa na uncontrolled . This equipment should be installed and operated with minimum distance n the radiator and your body.

RTANTE: (Pour l'utilisation de dispositifs mobiles)

'exposition aux radiations:

ent est conforme aux limites d'exposition aux rayonnements IC tablies pour ment non contrl. Cet quipement doit tre install et utilis avec un 20 cm de distance entre la source de rayonnement et votre corps.

d Standalone Antenna Configurationsith FCC RF exposure requirements, antennas that are mounted externally at ons or operating near users at stand-alone desktop of similar configurations with a minimum separation distance of 20 cm from all persons.

C RF exposure requirements, a mobile transmitting device must operate with a paration distance of 20 cm or more from a persons body.

Supplyan be powered from a 802.3af compliant power source which is certified by the gencies.

Radio Frequency Interference Requirements FCC

Altitude 453

Radio Frequency Interference Requirements FCC

Note: This equipment has been tested and found to comply with the limits

accordance wHowever thethis equipmebe determinethe interferen

Reorient o

Increase t

Connect treceiver is

Consult th

Radio TranThis device ctwo conditioaccept any in

For RLAN D

The use of 5

Notched B

Radio CanadaThis Class B

Cet appareil 2 Series Access Point Installation Guide53

for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

ith the instructions, may cause harmful interference to radio communications. re is no guarantee that interference will not occur in a particular installation. If nt does cause harmful interference to radio or television reception, which can d by turning the equipment off and on, the user is encouraged to try to correct ce by one or more of the following measures:

r relocate the receiving antenna

he separation between the equipment and receiver

he equipment into an outlet on a circuit different from that to which the connected

e dealer or an experienced radio/TV technician for help

smitters (Part 15)omplies with Part 15 of the FCC Rules. Operation is subject to the following ns: (1) this device may not cause harmful interference, and (2) this device must terference received, including interference that may cause undesired operation.

evices:

GHz RLANs, for use in the US, have the following restrictions:

and 5.60 5.65 GHz

Frequency Interference Requirements

digital apparatus complies with Canadian ICES-003.

numrique de la classe B est conforme la norme NMB-003 du Canada.

CE Marking and European Economic Area (EEA)

Altitude 453

Radio TransmittersFor RLAN Devices:The use of 5 GHz RLANs, for use in Canada, have the following restrictions:

Restricted

This device ctwo conditioaccept any in

Ce dispositifradio exemptdispositif ne tout brouillagindsirable.

Label MarkinCanada techn

To reduce pobe so chosenpermitted for

This device hWireless LANlist or havingantenna imp

CE Ma(EEA)

The urestric

MaximumGHz.

France, ou

Italy requ2 Series Access Point Installation Guide54

Band 5.60 5.65 GHz

omplies with RSS 210 of Industry Canada. Operation is subject to the following ns: (1) this device may not cause harmful interference and (2) this device must terference received, including interference that may cause undesired operation.

est conforme la norme CNR-210 d'Industrie Canada applicable aux appareils s de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter e reu, y compris un brouillage susceptible de provoquer un fonctionnement

g: The Term "IC:" before the radio certification only signifies that Industry ical specifications were met.

tential radio interference to other users, the antenna type and its gain should that the equivalent isotropically radiated power (EIRP) is not more than that successful communication.

as been designed to operate with the antennas listed in section 13 of Enterprise Antenna Specification Guide (72E-133063-01). Antennas not included in this

a greater gain are strictly prohibited for use with this device. The required edance is 50 ohms.

rking and European Economic Area

se of 2.4 GHz RLANs, for use through the EEA, have the following tions:

radiated transmit power of 100 mW EIRP in the frequency range 2.400 -2.4835

tside usage is restricted to 2.4 2.454 GHz.

ires a user license for outside usage.

Statement of Compliance

Altitude 453

Statement of ComplianceExtreme Networks hereby, declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A Declaration of Conformity m

Wa(W

English: For Efor recycling. Fhttp://www.extrFranais: Clie Extreme Netconsultez : httpEspaol: ParaNetworks al findevolver un prBulgarish: Extreme Netwohttp://www.extrDeutsch: Fr Recycling an Efinden Sie unteItaliano: per i essere restituitrestituzione, viPortugus: PaNetworks parahttp://www.extrNederlands: VExtreme Netwhttp://www.extrPolski: Klienci zExtreme Netwinternetowej htetina: Pro zExtreme Netwhttp://www.extr2 Series Access Point Installation Guide55

ay be obtained from http://www.extremenetworks.com/go/rfcertification.htm.

ste Electrical and Electronic Equipment EEE)U Customers: All products at the end of their life must be returned to Extreme Networks or information on how to return product, please go to: emenetworks.com/go/eu-weee.nts de l'Union Europenne: Tous les produits en fin de cycle de vie doivent tre retourns works pour recyclage. Pour de plus amples informations sur le retour de produits, ://www.extremenetworks.com/go/eu-weee. clientes en la Unin Europea: todos los productos debern entregarse a Extreme al de su ciclo de vida para que sean reciclados. Si desea ms informacin sobre cmo oducto, visite: http://www.extremenetworks.com/go/eu-weee. : rks . , : emenetworks.com/go/eu-weee.Kunden innerhalb der EU: Alle Produkte mssen am Ende ihrer Lebensdauer zum xtreme Networks zurckgesandt werden. Informationen zur Rcksendung von Produkten r http://www.extremenetworks.com/go/eu-weee.

clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita devono i a Extreme Networks al fine di consentirne il riciclaggio. Per informazioni sulle modalit di sitare il seguente sito Web: http://www.extremenetworks.com/go/eu-weee.ra clientes da UE: todos os produtos no fim de vida devem ser devolvidos Extreme

reciclagem. Para obter informaes sobre como devolver o produto, visite: emenetworks.com/go/eu-weee.oor klanten in de EU: alle producten dienen aan het einde van hun levensduur naar

orks te worden teruggezonden voor recycling. Raadpleeg emenetworks.com/go/eu-weee voor meer informatie over het terugzenden van producten. obszaru Unii Europejskiej: Produkty wycofane z eksploatacji naley zwrci do firmy

orks w celu ich utylizacji. Informacje na temat zwrotu produktw znajduj si na stronie tp://www.extremenetworks.com/go/eu-weee.kaznky z EU: Vechny produkty je nutn po skonen jejich ivotnosti vrtit spolenosti

orks k recyklaci. Informace o zpsobu vrcen produktu najdete na webov strnce: emenetworks.com/go/eu-weee.

Waste Electrical and Electronic Equipment (WEEE)

Altitude 453

Eesti: EL klientidele: kik tooted tuleb nende eluea lppedes tagastada taaskasutamise eesmrgil Extreme Networks'ile. Lisainformatsiooni saamiseks toote tagastamise kohta klastage palun aadressi: http://www.extremenetworks.com/go/eu-weee.Magyar: Az EU-ban vsrlknak: Minden tnkrement termket a Extreme Networks vllalathoz kell eljuttatni jrahasznosts cljbl. A termk visszajuttatsnak mdjval kapcsolatos tudnivalkrt ltogasson el aSvenska: Fr Networks fr http://www.extrSuomi: AsiakkNetworks-yhtihttp://www.extrDansk: Til kunudtjent. Ls ohttp://www.extr: .Malti: Gal klijrritornati gandjekk jogbok Romnesc: Preturnate la Exhttp://www.extrSlovenski: ZaNetworks za rehttp://www.extrSlovenina: Pvrten spolohttp://www.extrLietuvi: ES vkompanij Exhttp://www.extrLatvieu: ES Networks otrreldzu, skatiet: Trke: AB Miade edilmelidihttp://www.extr

Turkish WEEE

EEE Ynetme2 Series Access Point Installation Guide56

http://www.extremenetworks.com/go/eu-weee weboldalra.kunder inom EU: Alla produkter som uppntt sin livslngd mste returneras till Extreme tervinning. Information om hur du returnerar produkten finns p emenetworks.com/go/eu-weee.aat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierrtettvksi Extreme n, kun tuotetta ei en kytet. Listietoja tuotteen palauttamisesta on osoitteessa emenetworks.com/go/eu-weee.der i EU: Alle produkter skal returneres til Extreme Networks til recirkulering, nr de er plysningerne om returnering af produkter p: emenetworks.com/go/eu-weee. ..: , , Extreme Networks . , http://www.extremenetworks.com/go/eu-weee

enti fl-UE: il-prodotti kollha li jkunu waslu fl-aar tal-ajja ta' l-uu taghom, iridu jiu Extreme Networks gar-riikla. Gal aktar tagrif dwar kif gandek tirritorna l-prodott, ur: http://www.extremenetworks.com/go/eu-weee.entru clienii din UE: Toate produsele, la sfritul duratei lor de funcionare, trebuie treme Networks pentru reciclare. Pentru informaii despre returnarea produsului, accesai: emenetworks.com/go/eu-weee. kupce v EU: vsi izdelki se morajo po poteku ivljenjske dobe vrniti podjetju Extreme ciklao. Za informacije o vrailu izdelka obiite: emenetworks.com/go/eu-weee.re zkaznkov z krajn EU: Vetky vrobky musia by po uplynut doby ich ivotnosti nosti Extreme Networks na recyklciu. Bliie informcie o vrten vrobkov njdete na: emenetworks.com/go/eu-weee.artotojams: visi gaminiai, pasibaigus j eksploatacijos laikui, turi bti grinti utilizuoti treme Networks. Daugiau informacijos, kaip grinti gamin, rasite: emenetworks.com/go/eu-weee.klientiem: visi produkti pc to kalpoanas ma beigm ir jnogd atpaka Extreme izjai prstrdei. Lai iegtu informciju par produktu nogdanu Extreme Networks, http://www.extremenetworks.com/go/eu-weee.terileri iin: Kullanm sresi dolan tm rnler geri dntrme iin Extreme Networks'ya r. rnlerin nasl iade edilecei hakknda bilgi iin ltfen u adresi ziyaret edin: emenetworks.com/go/eu-weee.

Statement of Compliance

liine Uygundur

Japan (VCCI) - Voluntary Control Council for Interference

Altitude 453

Japan (VCCI) - Voluntary Control Council for Interference

Class B

This is a ClasInterference ftelevision recuse the equip

Korea

B

(

(Broadcasti2 Series Access Point Installation Guide57

ITE

s B product based on the standard of the Voluntary Control Council for rom Information Technology Equipment (VCCI). If this is used near a radio or eiver in a domestic environment, it may cause radio interference. Install and ment according to the instruction manual.

Warning Statement for Class B ITE

B )

(B )

, .

Class B ng Communication Device for Home Use)

This device obtained EMC registration mainly for home use (Class B) and may be used in all areas.

Other Countries

Altitude 453

Other Countries

AustraliaUse of 5 GHz

Brazil

RegulatoryNote: The ceEquipment. Tprotection agAlso this equ

For more info

DeclaraNota: "A maequipamentointerferncia a sistemas op

Para maiores

ChileEste equipotelecomunica

"This device telecommuni2 Series Access Point Installation Guide58

RLANs in Australia is restricted in the following band 5.50 5.65 GHz.

declarations for Altitude 4532- BRAZILrtification mark applied to the Altitude 4532 is for Restrict Radiation his equipment operates on a secondary basis and does not have the right for ainst harmful interference from other users including same equipment types. ipment must not cause interference to systems operating on primary basis.

rmation consult the website http://www.anatel.gov.br

es Regulamentares para AP-650 - Brasilrca de certificao se aplica ao Transceptor, modelo Altitude 4532. Este opera em carter secundrio, isto , no tem direito a proteo contra prejudicial, mesmo de estaes do mesmo tipo, e no pode causar interferncia erando em carter primrio.

informaes sobre ANATEL consulte o site: http://www.anatel.gov.br

cumple con la Resolucin No 403 de 2008, de la Subsecretaria de ciones, relativa a radiaciones electromagnticas..

complies with the Resolution Not 403 of 2008, of the Undersecretary of cations, relating to electromagnetic radiation.

Other Countries

Altitude 453

ChinaQuality Certificate in Chinese when the factory has ISO 9001 certification.

Mexico Restrict Freq

South KFor a radio eexpression sh

2 Series Access Point Installation Guide59

uency Range to: 2.450 2.4835 GHz.

oreaquipment using 2400~2483.5MHz or 5725~5825MHz, the following two ould be displayed:

Other Countries

Altitude 453

Taiwan

5.25-52 Series Access Point Installation Guide60

.35

Altitu

CHA

Customer Support

NOTE

Serviyou are an enplease contact

Extreme Netcoverage. Threlated questaspects of theTechnical As

http://www.extr

The ExtremeNetworks prupdates or pfor contactingthe eSupport

https://esuppo

RegistrationIf you have not already registered withsupplied with your product, you can r

http:/de 4532 Series Access Point Installatio

/www.extremenetworks.com/go/productren Guide61

Extreme Networks using a registration card egister on the Extreme Networks website at:

gistrationPTER6ces can be purchased from Extreme Networks or through one of its channel partners. If d-user who has purchased service through an Extreme Networks channel partner, your partner first for support.

works Technical Assistance Centers (TAC) provide 24x7x365 worldwide ese centers are the focal point of contact for post-sales technical and network-ions or issues. TAC will create a Service Request (SR) number and manage all SR until it is resolved. For a complete guide to customer support, see the

sistance Center User Guide at:

emenetworks.com/go/TACUserGuide

Networks eSupport website provides the latest information on Extreme oducts, including the latest Release Notes, troubleshooting, downloadable atches as appropriate, and other useful information and resources. Directions the Extreme Networks Technical Assistance Centers are also available from

website at:

rt.extremenetworks.com

Chapter 6: Customer Support

62

DocumentationCheck for the latest versions of documentation on the Extreme Networks documentation website at:

http://www.extrAltitude 4532 Series Access Point Installation Guide

emenetworks.com/go/documentation

Table of ContentsIntroductionDocument ConventionsWarningsSite PreparationAltitude 4532 Access Point Package ContentsExternal Antenna Model Package ContentsIntegrated Antenna Model Package Contents

Features

Hardware InstallationInstallation InstructionsPrecautionsAccess Point PlacementIntegrated Antenna Model Wall Mount InstructionsWall Mount HardwareWall Mount Procedure

Integrated Antenna Model Suspended Ceiling T-Bar Mount InstructionsSuspended Ceiling Mount Procedure

External Antenna Model Wall Mount InstructionsWall Mount HardwareWall Mount Procedure

External Antenna Model Suspended Ceiling Tile (Plenum) Mount InstructionsSuspended Ceiling Mount HardwareCeiling Mount Procedure

Antenna Options for Altitude 4532 Access Point External AntennaLED Indicators

Defining A Basic ConfigurationUsing the Initial Setup Wizard

SpecificationsAltitude 4532 Access Point External Antenna Model Electrical CharacteristicsAltitude 4532 Access Point External Antenna Model Physical CharacteristicsAltitude 4532 Access Point Integrated Antenna Model Electrical CharacteristicsAltitude 4532 Access Point Integrated Antenna Model Physical CharacteristicsRadio Characteristics

Regulatory InformationRegulatory InformationWireless Device Country ApprovalsCountry SelectionFrequency of Operation FCC and IC5 GHz OnlyIndustry Canada Statement:

Health and Safety RecommendationsWarnings for Use of Wireless DevicesPotentially Hazardous Atmospheres Fixed InstallationsSafety in HospitalsPacemakersOther Medical Devices

RF Exposure GuidelinesSafety InformationReducing RF ExposureUse Properly

InternationalEuropeRemote and Standalone Antenna Configurations

US and CanadaCo-located statementRemote and Standalone Antenna Configurations

Power SupplyRadio Frequency Interference Requirements FCCRadio Transmitters (Part 15)

Radio Frequency Interference Requirements CanadaRadio Transmitters

CE Marking and European Economic Area (EEA)Statement of ComplianceWaste Electrical and Electronic Equipment (WEEE)Japan (VCCI) - Voluntary Control Council for InterferenceClass B ITE

Korea Warning Statement for Class B ITEOther CountriesAustraliaBrazilRegulatory declarations for Altitude 4532- BRAZILDeclaraes Regulamentares para AP-650 - Brasil

ChileChinaMexicoSouth KoreaTaiwan

Customer SupportRegistrationDocumentation

/ColorImageDict > /JPEG2000ColorACSImageDict > /JPEG2000ColorImageDict > /AntiAliasGrayImages false /CropGrayImages true /GrayImageMinResolution 300 /GrayImageMinResolutionPolicy /OK /DownsampleGrayImages true /GrayImageDownsampleType /Bicubic /GrayImageResolution 300 /GrayImageDepth -1 /GrayImageMinDownsampleDepth 2 /GrayImageDownsampleThreshold 1.50000 /EncodeGrayImages true /GrayImageFilter /DCTEncode /AutoFilterGrayImages true /GrayImageAutoFilterStrategy /JPEG /GrayACSImageDict > /GrayImageDict > /JPEG2000GrayACSImageDict > /JPEG2000GrayImageDict > /AntiAliasMonoImages false /CropMonoImages true /MonoImageMinResolution 1200 /MonoImageMinResolutionPolicy /OK /DownsampleMonoImages true /MonoImageDownsampleType /Bicubic /MonoImageResolution 1200 /MonoImageDepth -1 /MonoImageDownsampleThreshold 1.50000 /EncodeMonoImages true /MonoImageFilter /CCITTFaxEncode /MonoImageDict > /AllowPSXObjects false /CheckCompliance [ /None ] /PDFX1aCheck false /PDFX3Check false /PDFXCompliantPDFOnly false /PDFXNoTrimBoxError true /PDFXTrimBoxToMediaBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXSetBleedBoxToMediaBox true /PDFXBleedBoxToTrimBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXOutputIntentProfile () /PDFXOutputConditionIdentifier () /PDFXOutputCondition () /PDFXRegistryName () /PDFXTrapped /False

/Description > /Namespace [ (Adobe) (Common) (1.0) ] /OtherNamespaces [ > /FormElements false /GenerateStructure true /IncludeBookmarks false /IncludeHyperlinks false /IncludeInteractive false /IncludeLayers false /IncludeProfiles true /MultimediaHandling /UseObjectSettings /Namespace [ (Adobe) (CreativeSuite) (2.0) ] /PDFXOutputIntentProfileSelector /NA /PreserveEditing true /UntaggedCMYKHandling /LeaveUntagged /UntaggedRGBHandling /LeaveUntagged /UseDocumentBleed false >> ]>> setdistillerparams> setpagedevice

ap 4532 install guide

Documents

extreme ethernet

extreme networks

extreme turbodrive logo

extreme velocity

access point package

purple extreme solution

extremexos logo

alpine logo