the fastest way to join hdpe pipe — no ifs, ands, or … · flange adapter for hdpe-to- flanged...
Post on 03-Jun-2020
2 Views
Preview:
TRANSCRIPT
THE FASTEST WAY TO JOIN HDPE PIPE —NO IFS, ANDS, OR BUTTS.
GASKET
HOUSING
BOLT/NUT
STAINLESS STEEL TEETH
STAINLESS STEEL TEETH
ENGINEEREDPB-234 REV G
The Refuse-to-Fuse™ System for HDPE Pipe
PIPE JOINING TECHNOLOGY
SMALL DIAMETER
Dual rows of stainless steel teeth engage into the outside diameter of plain end HDPE as coupling housing halves are tightened bolt pad to bolt pad, allowing for visual confirmation of correct assembly.
LARGE DIAMETER
Coupling “keys” engage into double grooved HDPE pipe as coupling housing halves are tightened bolt pad to bolt pad, allowing for visual confirmation of correct assembly.
DESIGNED FOR BURIED, SUBMERGED, OR ABOVE GROUND APPLICATIONS
The Refuse-to-Fuse™ System for HDPE Pipe
TOUGH
HOW DOES IT WORK?
1refuse-to-fuse.com PB-234 REV G
FORGET FUSION
INSTALLS UP TO 10× FASTERJoin HDPE pipe in half the time it takes to fuse a joint. Forget the fusion equipment. Gone are the days of waiting for plastic to heat up just to cool down. Installing in tight or vertical spaces has never been easier; the Refuse-to-Fuse system goes where no fusion machine has gone before. That's time savings you've never seen before.
INSTALLATION IS WEATHER INDEPENDENTWhether it's rain, shine, or just downright frigid and fierce, Refuse-to-Fuse products can be installed. No need to check the weather forecast and worry about protection for fusion equipment or project delays any longer.
2 PB-234 REV G
The Refuse-to-Fuse™ System for HDPE Pipe
LUBE PUSH
INSTALLS WITH SIMPLE TOOLSNo need to set up your fancy fusion machine because all you will need with the Refuse-to-Fuse system is a simple socket wrench. If you want to get crazy, a cordless impact driver will do the job, too!
Don’t worry about training certificates or learning how to use fusion equipment, just stick with the basics.
MEETS OR EXCEEDS PRESSURE RATINGS OF HDPE PIPEIf you thought your fused joint was tough, check out Refuse-to-Fuse product performance. Small diameter solutions call for dual rows of razor-sharp teeth that sink into the O.D. of HDPE pipe, forming a sealed hold that never lets go. Bringing out the big guns? Large diameter solutions enlist a rugged double groove to seal the deal. Push it, pull it, and drag it to the max; treat it the same way you would treat fused pipe.
Electrofusion 1.3
Flanging 2.5
6
20
Butt Fusion
MechanicalCoupling
HDPE joints completed per hour on 4" SDR 11 HDPE pipeThe Refuse-to-Fuse™ System for HDPE Pipe
“WITH THIS COUPLING, IT’S SO EASY... JUST MARK THE DEPTH, SLIDE THE PIPE IN AND TIGHTEN IT UP... MUCH FASTER THAN FUSING.” Dave, Stone Hill Contracting
refuse-to-fuse.com 3 PB-234 REV G
The Refuse-to-Fuse™ System for HDPE Pipe
JOIN TIGHTEN
Installation-Ready™ Refuse-to-Fuse™ Coupling for Plain End HDPE PipeSTYLE 905
Download publication 19.07 for complete information
• Designed for plain end HDPE pipe (SDR 7 – SDR 21)
• Sizes from 2 – 8" IPS and 63 – 225 mm ISO
Certifications/Listings:
WaterMark
Download publication 10.01 for complete information
SMALL DIAMETER
4 PB-234 REV G
The Refuse-to-Fuse™ System for HDPE Pipe
INST
ALLA
TION-
READY
™
Installation-Ready™ Refuse-to-Fuse™ Flange Adapter for HDPE-to- Flanged PipeSTYLE 904
Download publication 19.12 for complete information
• Designed to provide a single transition from plain end HDPE pipe (SDR 7 – SDR 21) to flanged piping system components
• Sizes from 3 – 8" IPS HDPE to 3 – 8" IPS ANSI Class 150 Flange
Refuse-to-Fuse™ Transition Coupling for HDPE-to-Steel PipeSTYLE 907
Download publication 19.10 for complete information
• Designed to provide a single transition from plain end HDPE pipe (SDR 7 – SDR 21) to grooved steel sized piping system components
• Sizes from 2 – 8" IPS HDPE to 2 – 8" | DN50 – DN200 grooved steel
• Sizes from 63 – 225 mm ISO HDPE to 2 – 8" | DN50 – DN200 grooved steel Certifications/Listings:
WaterMark
Download publication 10.01 for complete information
refuse-to-fuse.com 5 PB-234 REV G
The Refuse-to-Fuse™ System for HDPE Pipe
INST
ALLA
TION-
READY
™
Refuse-to-Fuse™ Fittings for HDPE Pipe
Download publication 19.11 for complete information
• Available in SDR 7, SDR 11, and SDR 17
• Sizes from 2 – 8" IPS and 63 – 225 mm ISO
• Full flow fittings
• Compatible for use with Style 905 and 907 HDPE couplings
No. H10 90° Elbow
No. H11 45° Elbow
No. H20 Tee
No. H50 Reducer
INST
ALLA
TION-
READY
™
Refuse-to-Fuse™ Coupling for Double-Grooved HDPE PipeSTYLE 908
Download publication 19.09 for complete information
• Designed for double grooved HDPE (SDR 7 – SDR 21)
• Sizes from 8 – 36" IPS and 250 – 900 mm ISO
• Larger diameter couplings have lifting lugs for easy maneuvering around the job site
• Standard Victaulic coupling assembly procedure used for installation
Mechanical-T Spigot OutletSTYLE 926
Download publication 11.07 for complete information
• Designed to provide an outlet connection on HDPE, steel, and ductile iron pipe materials in IPS, ISO, and AWWA pipe sizes
• 4" outlets available for 10 – 32" IPS pipe diameters
• 114.3 mm outlets available for 250 – 800 mm ISO pipe diameters
• 6" outlets available for 16 – 48" IPS pipe diameters
• 168.3 mm outlets available for 400 – 1200 mm ISO pipe diameters
Refuse-to-Fuse™ Cut Grooving Tool for HDPE PipeCG3100 8 – 18" IPS | 250 – 450 mm ISO CG3300 16 – 26" IPS | 400 – 630 mm ISO CG3500 24 – 36" IPS | 630 – 900 mm ISO
Download publication 24.06 for complete information
• Designed for cut grooving HDPE (SDR 7 – SDR 21) pipe
• Provides the only grooved joining solution for large diameter HDPE pipe
• Faces and cuts parallel grooves into the end of the pipe
Certifications/Listings:
WaterMark
Download publication 10.01 for complete information
refuse-to-fuse.com 7 PB-234 REV G
The Refuse-to-Fuse™ System for HDPE Pipe
WEATHER INDEPENDENT | LIGHTWEIGHT | PORTABLE | SMALL FOOTPRINT
CASE STUDYATLAS RESOURCES HAMMANSALT WATER DISPOSALIn June 2015, construction was completed at the Atlas Resources Hamman salt water disposal (SWD) facility in Jacksboro, Texas. The Hamman facility is comprised of ten water tanks, two oil tanks, one gun barrel, and three offload stations. Prior to its commencement, the project’s contractor knew the job would be laden with challenges associated with joining HDPE pipe while facing construction schedule constraints.
88 PB-234 REV G
The Refuse-to-Fuse™ System for HDPE Pipe
CASE STUDYATLAS RESOURCES HAMMANSALT WATER DISPOSAL
Fusing HDPE pipe would be an unfavorable option because of its extremely time-consuming nature. Additionally, fusion would require good weather conditions in order to allow for proper mending of fusion welds.
Prefabrication options and new Victaulic HDPE products boasted several attractive benefits, including controlled costs and a dramatic improvement on the SWD facility’s completion date. Victaulic was able to provide a hard number for the prefabrication piece of the project and presented the new Style 908, Style 907, and Style 905 HDPE couplings as a way to finish the job in just 3 – 4 weeks, according to Atlas Resources personnel.
During the first week of assembly, the job site was hit with high winds and 11 – 13" | 28 – 33 cm of rain. Fortunately, thanks to Victaulic, construction was able to remain on schedule, with the prefabricated portion finishing in 6 days and the offload station and additional piping finishing in 10 days. The easy-to-install Victaulic HDPE couplings were the ideal solution to deal with heavy rain and wet conditions, especially when compared with HDPE fusion.
After successfully overcoming various challenges by using Victaulic HDPE solutions, the Hamman facility was recognized by the Plastic Pipe Institute (PPI) and received the 2016 Energy Piping Systems Division Project of the Year award.
SPECIFICATIONSServices: Pipe Materials: Pipe Size Range:
Gun Barrel Piping SDR 9 HDPE 10" IPS
Offload Station SDR 9 HDPE 4 – 6" IPS
Tank Manifold Piping SDR 9 HDPE 8 – 10" IPS
Oil Carbon Steel 2 – 4" IPS
PROJECT Type of Facility:
Salt Water Disposal
Victaulic Solutions:
Construction Piping ServicesEase and Speed of InstallationInstallation Time SavingsPrefabrication
Owner:
Atlas Resources
Contractor:
Black Sheep
Engineer/Consultant:
Atlas Resources
refuse-to-fuse.com 9 PB-234 REV G
The Refuse-to-Fuse™ System for HDPE Pipe
refuse-to-fuse.com
PB-234 0951 REV G 09/2017Victaulic and all other Victaulic marks are the trademarks or registered trademarks of Victaulic Company, and/or its affiliated entities, in the U.S. and/or other countries. All other trademarks listed herein are the property of their respective holders, in the U.S. and/or other countries. The terms “Patented” or “Patent Pending” refer to design or utility patents or patent applications for articles and/or methods of use in the United States and/or other countries.
© 2017 VICTAULIC COMPANY. ALL RIGHTS RESERVED.
UNITED STATES ANDWORLD HEADQUARTERS
4901 Kesslersville RoadEaston, PA 18040 USA
1 800 PICK VIC1 800 742 5842(within North America)1 610 559 3300
pickvic@victaulic.com
CANADA
123 Newkirk RoadRichmond HillOntario L4C 3G5 Canada
1 905 884 7444
viccanada@victaulic.com
MEXICO
Calle Circuito del MarquésNo 8 al 11Parque Industrial El MarquésMunicipio El MarquésQueretaro, MexicoCP 76246
52 442 253 0066
vical@victaulic.com
BRAZIL
Av. Marquês de São Vicente446 Cj 1303Várzea da Barra Funda –São Paulo-SPCEP 01139-000 – Brazil
55 11 3548 4280
vicbr@victaulic.com
BELGIUMEUROPE HEADQUARTERS
Prijkelstraat 369810 Nazareth, Belgium
32 9 381 15 00
49 6151 9573 0(within Germany)
viceuro@victaulic.com
UNITED KINGDOM
Units B1 & B2, SG1 Industrial ParkCockerell Close, Gunnels Wood RoadStevenage, Hertfordshire, UKSG 1 2NB
44 1438 310 690
viceuro@victaulic.com
UNITED ARAB EMIRATES
FZ LIU10 AA01, AA02, AA03, AA04 and AA05Al Munawala StreetJebel Ali Freezone – SouthzonePO BOX 17683Jebel Ali, DubaiUAE-United Arab Emirates
971 4 883 88 70
viceuro@victaulic.com
INDIA
India Land Global Industrial ParkPlot 4, Hinjewadi, Phase-1, MulshiPune 411057, India
91 20 67 919 300
viceuro@victaulic.com
CHINA
Unit 808, Building BHongwell International PlazaNo.1602 West Zhongshan RoadShanghai, China 200235
86 21 6021 9400
vicap@victaulic.com
KOREA
4F, Seoil Building, 1430-5,Seocho-Dong, Seocho-GuSeoul, Korea 137-070
82 2 521 7235
vicap@victaulic.com
TAIWAN
No. 55, NanGong Rd, LuZhu DistrictTaoYuan City 338, Taiwan886 3 222 3220
vicap@victaulic.com
AUSTRALIA ANDNEW ZEALAND
7 Chambers RoadUnit 1Altona North, VictoriaAustralia 3025
1 300 PIC VIC1 300 742 842(within Australia)
0 508 PICK VIC0 508 7425 842(within New Zealand)
61 3 9392 4000
vicaust@victaulic.com
Asia PacificEurope, Middle East, Africa and IndiaNorth and South America
For additional locations, information andsupport, visit www.victaulic.com/contactus
top related