produced by khodr hussein drafting teacher cass technical high school detroit michigan

1. Identify and use the tools needed2. Secure the paper to the drawing board3. Draw the Border Lines4. Draw the Title Block with guidelines5. Add details and information in the title

block6. Understand the properties of the Working

Area

Straight Edge

Equipments you need: Drafting Board

Triangle

TriangleTriangle8.5 x 11

White paper

Drafting pencilsRuler

DraftingTape

1. Identify and use the tools needed2. Secure the paper to the drawing board3. Draw the Border Lines4. Draw the Title Block with guidelines6. Add details and information in the title block7. Understand the properties of the Working

Area

Straight Edge

2. Secure the paper to the drawing board

2.1 First: Place the Straight edge few inches above the bottom edge of the Drawing Board

Straight-Edge

2. Secure the paper to the drawing board2.2 Next: align the bottom edge of the paper to the top edge of the Straight-Edge

8.5 x 11White paper

Tip: you may roll up the two bottom corners of the paper so it would not slide under the edge

Next

Straight-Edge

2. Secure the paper to the drawing board2.3 Now: Tape both top edges of the paper

8.5 x 11White paper

tip: Keep the tape closer to the corner to allow for drawing the border lines.

Next

2. Secure the paper to the drawing board2.4 Finally: Tape both bottom edges of the paper

8.5 x 11White paper

Straight Edge

1. Identify and use the tools needed2. Secure the paper to the drawing board3. Draw the Border Lines4. Draw the Title Block with guidelines6. Add details and information in the title

block7. Understand the properties of the Working

Area

3. Draw the Border Lines3.1 First: using the Ruler, measure ½” from left edge of the paper

Straight Edge

½”

Tip: align the ruler with the straight edge and then place a light dash parallel to the edge on the ½” mark

Next

3. Draw the Border Lines3.2 Next: Draw a vertical line on the ½” mark

Straight Edge

½”Triangle

Note : This line must be very light

Next

Tip: draw line from top to bottom

3. Draw the Border Lines3.3 Measure ½” from right edge of the paper

Straight Edge

½” ½”Triangle

3. Draw the Border Lines3.4 Measure ½” from Top edge of the paper

Straight Edge

½” ½”½

”

Tip:Keep all lines light until you are instructed to darken

Next

3.5 Now Draw the Top Border Line

3. Draw the Border Lines3.6 Measure ½” from Bottom Edge of the paper

Straight Edge

½” ½”½

”

Next

3.7 Now Draw the BottomBorder Line

½”

1. Identify and use the tools needed2. Secure the paper to the drawing board3. Draw the Border Lines4. Draw the Title Block with guidelines6. Add details and information in the title block7. Understand the properties of the Working

Area

4. Draw the Title Block with guidelines4.1 Measure ½” from Bottom Border line

Straight Edge½

”

Next

4.2 Now Draw the top of the Title Block

Straight EdgeNext

4. Draw the Title Block with guidelines4.3 Now Layout the measurements for the guidelines

1/16 “1/8“

1/8“

1/8“1/16 “

½”

Next

4.4 Draw the guidelines4. Draw the Title Block with guidelines

Remember the measurements

4.5 Now draw the title block section dividers

3” 4” 3”

1. Identify and use the tools needed2. Secure the paper to the Drawing Board3. Draw the Border Lines4. Draw the Title Block with Guidelines6. Add details and information in the Title Block7. Understand the properties of the Working Area

½”

Next

6.1 Start with your Name in the Top Left Section

6. Add details and information in the Title Block

6.2 Add the Class, and the Semester under Name

3” 4” 3”

6.3 Add the Name of the Drawing in the Top Middle6.4Add the Topic Section under drawing Name6.5 Add the Date in the Top of End Section6.6 Add Teacher Name in Bottom End Section

JOHN DOEDRAFTING I

PREPARING WORK AREABASIC PROCEDURES

12/12/3001MR SEAN DOE

½”

Next

`You may darken necessary lines now

6. Add details and information in the Title Block

3” 4” 3”JOHN DOE

DRAFTING IPREPARING WORK AREABASIC PROCEDURES

12/12/3001MR SEAN DOE

Or wait until you fininsh the assigned drawing so you do not cause lead smudges while drawing

Next

1. Identify and use the tools needed2. Secure the paper to the Drawing Board3. Draw the Border Lines4. Draw the Title Block with Guidelines6. Add details and information in the Title Block7. Understand the properties of the Working Area

LENTH

½”

Next

7. Understand the properties of the Working Area

JOHN DOEDRAFTING I

PREPARING WORK AREABASIC PROCEDURES

12/12/3001MR SEAN DOE

Next

Length of the Working Area (LWA)

10”

Wid

th o

f th

e W

ork

ing

Are

a ( W

WA

)7”Given the Border Lines and

the Title Block, Always Remember:The Working Area has the following measurements

LWA = 10”WWA = 7”

The End