paris aircraft demonstrator (pad) general...
Post on 11-Mar-2018
221 Views
Preview:
TRANSCRIPT
COMMERCIAL IN CONFIDENCE
PARIS Aircraft Demonstrator
ENG.SP.EU.03.0117 Issue C
Page 1 of 29
SP_0117_C GenRqts.doc
COMMERCIAL IN CONFIDENCE
PARIS Aircraft Demonstrator (PAD)
General Requirements
Author Date:
Product Assurance Date:
Project Manager Date:
© EADS Astrium Limited, 2003
EADS Astrium Ltd owns the copyright of this document which is supplied in confidence and which shall not be used for any purpose other than that for which it is supplied and shall not in whole or in part be reproduced, copied, or
communicated to any person without written permission from the owner.
EADS Astrium Ltd Anchorage Road, Portsmouth, Hampshire, PO3 5PU, England
COMMERCIAL IN CONFIDENCE
PARIS Aircraft Demonstrator
ENG.EP.EU.03.0117 Issue C
Page 2 of 29
EADS Astrium Ltd owns the copyright of this document which is supplied in confidence and which shall not be used for any purpose other than that for which it is supplied and shall not in whole or in part be reproduced, copied, or communicated to any person without written permission from the owner.
SP_0117_C GenRqts.doc
COMMERCIAL IN CONFIDENCE
INTENTIONALLY BLANK
COMMERCIAL IN CONFIDENCE
PARIS Aircraft Demonstrator
ENG.EP.EU.03.0117 Issue C
Page 3 of 29
EADS Astrium Ltd owns the copyright of this document which is supplied in confidence and which shall not be used for any purpose other than that for which it is supplied and shall not in whole or in part be reproduced, copied, or communicated to any person without written permission from the owner.
SP_0117_C GenRqts.doc
COMMERCIAL IN CONFIDENCE
CONTENTS
1. SCOPE AND INTRODUCTION ........................................................................................................... 7 1.1 Scope ......................................................................................................................................... 7 1.2 Introduction ................................................................................................................................. 7 1.3 Study Context.............................................................................................................................. 7 1.4 Objectives of Project .................................................................................................................... 7
2. APPLICABLE AND REFERENCE DOCUMENTS ................................................................................. 8 2.1 Applicable Documents ................................................................................................................. 8 2.2 Reference Documents ................................................................................................................. 8
3. PHYSICAL CHARACTE RISTICS ........................................................................................................ 9 3.1 General....................................................................................................................................... 9 3.2 Configuration............................................................................................................................... 9 3.3 Mass Properties .......................................................................................................................... 9
3.3.1 Mass ................................................................................................................................. 9 3.3.2 Mass Budget ...................................................................................................................... 9 3.3.3 Centre of Gravity ...............................................................................................................10 3.3.4 Moment of Inertia ..............................................................................................................10
3.4 Electrical Requirements ..............................................................................................................10 3.4.1 General ............................................................................................................................10
3.5 Thermal Requirements................................................................................................................10 3.5.1 General ............................................................................................................................10 3.5.2 Temperatures Limits..........................................................................................................10 3.5.3 Thermal Finishes ...............................................................................................................11 3.5.4 Cooling.............................................................................................................................11 3.5.5 Analysis............................................................................................................................11
4. MECHANICAL DESIGN AND INTERFACES.......................................................................................11 4.1 General......................................................................................................................................11 4.2 Operability..................................................................................................................................14
4.2.1 Reliability ..........................................................................................................................14 4.2.2 Safety...............................................................................................................................14 4.2.3 Useful Life.........................................................................................................................15
4.3 Environment ...............................................................................................................................15 4.3.1 On-Ground Mechanical Environment ..................................................................................15
4.4 Design and Construction .............................................................................................................16 4.4.1 General ............................................................................................................................16 4.4.2 Venting Provisions .............................................................................................................16 4.4.3 Mounting Provisions ..........................................................................................................16 4.4.4 Parts, Materials and Processes ..........................................................................................16 4.4.5 Moisture and fungus resistance..........................................................................................16 4.4.6 Corrosion prevention and control ........................................................................................17 4.4.7 Identification and marking ..................................................................................................17 4.4.8 Documents and standards .................................................................................................17
4.5 Electro-Magnetic Compatibility.....................................................................................................17 4.5.1 Bonding & Isolation............................................................................................................18
5. VERIFICATION, CERTIFICATION AND TEST...................................................................................18 5.1 General Requirements ................................................................................................................18
5.1.1 Responsibility for Tests......................................................................................................18 5.1.2 Airworthiness testing (reference AD2) .................................................................................18
COMMERCIAL IN CONFIDENCE
PARIS Aircraft Demonstrator
ENG.EP.EU.03.0117 Issue C
Page 4 of 29
EADS Astrium Ltd owns the copyright of this document which is supplied in confidence and which shall not be used for any purpose other than that for which it is supplied and shall not in whole or in part be reproduced, copied, or communicated to any person without written permission from the owner.
SP_0117_C GenRqts.doc
COMMERCIAL IN CONFIDENCE
5.1.3 Certification for Airworthiness.............................................................................................19 5.2 Testing.......................................................................................................................................20
5.2.1 Test Conditions .................................................................................................................20 5.2.2 Testing for Airworthiness....................................................................................................21
6. .........................................................................................................................................................27
TABLES Table 3-1 Mass Budget .......................................................................................................................... 9 Table 3-2 Unit/ Sub-system Temperature Requirements..........................................................................11 Table 4-1 Applied Safety Factors ...........................................................................................................13 Table 4-2 Structural Failure Modes.........................................................................................................14 Table 4-3 Limit Accelerations for Ground Operations ...............................................................................15 Table 4-4 Limit Accelerations for Ground Operations ...............................................................................16 Table 5-1 EMC Applicability Matrix.........................................................................................................27
FIGURES Figure 1-1 Block schematic of the Airborne Demonstrator......................................................................... 8 Figure 4-1 Typical Configuration ...........................................................................................................12 Figure 5-1 Standard Random Vibration Test Curves for Equipment installed in Fixed Wing Aircraft with
Turbojet of Turbofan Engines .........................................................................................................22 Figure 5-2 Shock Measuring system Frequency Response......................................................................23 Figure 5-3 Terminal Saw-tooth Shock Pulse Configuration and its Tolerance Limits ..................................24 Figure 5-4 Thermal Test Cycle Profile ....................................................................................................25 Figure 5-5 Altitude Test .........................................................................................................................26
COMMERCIAL IN CONFIDENCE
PARIS Aircraft Demonstrator
ENG.EP.EU.03.0117 Issue C
Page 5 of 29
EADS Astrium Ltd owns the copyright of this document which is supplied in confidence and which shall not be used for any purpose other than that for which it is supplied and shall not in whole or in part be reproduced, copied, or communicated to any person without written permission from the owner.
SP_0117_C GenRqts.doc
COMMERCIAL IN CONFIDENCE
ABBREVIATIONS
AC Alternating Current ESA European Space Agency ACT Advanced CMOS TTL -compatible
logic device ESTEC European Space Research and
Technology Centre
AD Applicable Document EU European Union ADD Architectural Design Document
(Software) FACT Framework Architecture for
Communication Technologies
AFT Abbreviated Functional Test FEM Finite Element Model AIT Assembly Integration and Test FESS Front -End Subsystem AIV Assembly, Integration and Verification GSE Ground Support Equipment
ASAR Advanced Synthetic Aperture Radar I/F Interface ASIC Application Specific Integrated Circuit IC Integrated Circuit BBE Base Band Equipment ICD Interface Control Doc/ Dwg BOL Beginning Of Life ID Identification C&C Command & Control IFE Intermediate Freq Equipment CAN Controller Area Network INS Inertial Navigation System CE Conducted Emissions IRF Impulse Response Function CMOS Complementary Metal Oxide
Semiconductor ISO International Standards Organisation
CNES Centre National d'Etudes Spatiales ITU International Telecommunications Union CORE Common Radar Electronics LNA Low Noise Amplifier CPC not Applicable LS Low Side (Drive Transistor) CRC Cyclic Redundancy Check LSAR L-Band Synthetic Aperture Radar CRESS Core Radar Electronics Subsystem L-SAR L-Band Synthetic Aperture Radar CS Cornerstone mission/ Cooler System LSB Least Significant Bit DAC Digital to Analogue Converter MAC Media Access Control DC Direct Current MGSE Mechanical Ground Support Equipment DCL Declared Components List MOI Moment of Inertia DEG not Applicable MS Material Specification DLC Data Length Code/ Digital Loop
Carrier MSB Most Significant Bit
DM Demonstrator Model N/A Not Applicable ECSS European Co-operation for Space
Standardisation PCB Printed Circuit Board
EEPROM Electrically Erasable Programmable Read Only Memory
PDM Pre-Development Model
EIA Electronic Industries Association PRF Pulse Repetition Frequency EIRP Equivalent Isotropic Radiated Power PRI Pulse Repetition Interval EMC Electro-Magnetic Compatibility PSU Power Supply Unit EOL End Of Life RAM Random Access Memory RF Radio Frequency RTR RT Remote Terminal RTR Remote Transmission Request-bit RX Receiver SAR Synthetic Aperture Radar SI System Imaging/Service Information
COMMERCIAL IN CONFIDENCE
PARIS Aircraft Demonstrator
ENG.EP.EU.03.0117 Issue C
Page 6 of 29
EADS Astrium Ltd owns the copyright of this document which is supplied in confidence and which shall not be used for any purpose other than that for which it is supplied and shall not in whole or in part be reproduced, copied, or communicated to any person without written permission from the owner.
SP_0117_C GenRqts.doc
COMMERCIAL IN CONFIDENCE
SINDA Systems Improved Numerical Differencing Analyser
SLIO Serial Link I/O SP Sample Plan SPF Single Point Failure SSB Single Sideband STP Shielded Twisted Pair T/R Transmit/Receive TBC To Be Confirmed TBD To Be Determined TCS Thermal Control subsystem TCU Tile Control Unit TMTC Telemetry/Telecommand TPL Tribology Parts Library TR Tracking TTL Transistor-Transistor Logic TX Transmit UK United Kingdom VIP Video Interface Port WCA Worst Case Analysis
COMMERCIAL IN CONFIDENCE
PARIS Aircraft Demonstrator
ENG.EP.EU.03.0117 Issue C
Page 7 of 29
EADS Astrium Ltd owns the copyright of this document which is supplied in confidence and which shall not be used for any purpose other than that for which it is supplied and shall not in whole or in part be reproduced, copied, or communicated to any person without written permission from the owner.
SP_0117_C GenRqts.doc
COMMERCIAL IN CONFIDENCE
1. SCOPE AND INTRODUCTION
1.1 Scope
This document defines the requirements for the general Requirements and Environments for Airworthiness which will be required for the Airborne Demonstrator. This demonstrator will use prototype hardware which will be produced to de-risk the development for an potential space borne instrument. 1.2 Introduction
Traditional nadir-looking altimeters have very limited capabilities to observe Mesoscale Ocean Topography. Mesoscale phenomena require higher spatial-temporal sampling in the order of 50 km – 7 days. The PARIS (Passive Reflectometry and Interferometric System) concept was conceived by ESA in 1993 as an alternative technique to increase the sampling of the ocean surface from a single Low Earth Orbit (LEO) platform. It consists in combining direct and ocean reflected signals from opportunity sources, such as Global Navigation Satellite System (GNSS) signals, to perform ocean altimetry. By-products of this processing are ocean wind, significant wave height and ionospheric Total Electron Content (TEC) over the ocean. The present activity is part of a mini-project that aims at the definition of a PARIS sensor primarily used for mesoscale ocean altimetry. 1.3 Study Context
The present activity titled PARIS Technology Concept Definition –Phase 2 (Phase 2 of TRP ETD -137.A) is part of the PARIS mini-project (TRP ETD-137). 1.4 Objectives of Project
The project is intended to provide Technology demonstrations of critical technologies which will be required for a space PARIS Mission. To achieve this end three technology projects will provide hardware which will be integrated into an Airborne Demonstrator. The overall system which will be used in the Airborne Demonstrator (PADS) is shown in Figure 1-1. This shows the major hardware items which will be required. Of these the following will be subject to Pre-development activities:
• Up-looking GPS Receiver • Multi-beam Array • Beamformer and Receiver • Signal Processor
The demonstrator items which are specified in this specification are intended to reduce the technology risks in a flight program. To achieve this the designs shall consider the implications of design for flight by choosing techniques and devices which ultimately can be used for space hardware.
COMMERCIAL IN CONFIDENCE
PARIS Aircraft Demonstrator
ENG.EP.EU.03.0117 Issue C
Page 8 of 29
EADS Astrium Ltd owns the copyright of this document which is supplied in confidence and which shall not be used for any purpose other than that for which it is supplied and shall not in whole or in part be reproduced, copied, or communicated to any person without written permission from the owner.
SP_0117_C GenRqts.doc
COMMERCIAL IN CONFIDENCE
60 deg Raydome
AntennaLNAs & Phase Shifters
Pressure BulkheadCables
RX
Processor
Mass Storage
Upwardlooking RX
Upward Looking Antenna
PowerConverter
AircraftSupply
115V 400Hz
28VdcController Man Machine Interface
BFN
Electronic Assembly
FixingsAnd
Av Mounts Cabin Floor
INS
Part of aircraftsystem
Part of aircraftsystem
60 deg Raydome
AntennaLNAs & Phase Shifters
Pressure BulkheadCables
RX
Processor
Mass Storage
Upwardlooking RX
Upward Looking Antenna
PowerConverter
AircraftSupply
115V 400Hz
28VdcController Man Machine Interface
BFN
Electronic Assembly
FixingsAnd
Av Mounts Cabin Floor
INS
Part of aircraftsystem
Part of aircraftsystem
Figure 1-1 Block schematic of the Airborne Demonstrator
2. APPLICABLE AND REFERENCE DOCUMENTS
2.1 Applicable Documents
AD1 Mil-Std-461 Electromagnetic Emission and Susceptibility Requirements for the Control of Electromagnetic Interference
AD2 RTCA/DO-160D Environmental Conditions and Test Procedures for Airborne Equipment
2.2 Reference Documents
RD1
COMMERCIAL IN CONFIDENCE
PARIS Aircraft Demonstrator
ENG.EP.EU.03.0117 Issue C
Page 9 of 29
EADS Astrium Ltd owns the copyright of this document which is supplied in confidence and which shall not be used for any purpose other than that for which it is supplied and shall not in whole or in part be reproduced, copied, or communicated to any person without written permission from the owner.
SP_0117_C GenRqts.doc
COMMERCIAL IN CONFIDENCE
3. PHYSICAL CHARACTERISTICS
3.1 General
The hardware being developed will be used in an airborne demonstrator. However, it is intended that the results will represent a stage towards Spaceborne designs of important sections of the PARIS Sensor. Therefore, the electrical, mechanical and software should be capable of enhancement for a potential future space mission. The developed hardware will be integrated into a complete sensor which will be capable of being operated in an airborne environment. This infers certain levels of certification for airworthiness. 3.2 Configuration
The Multibeam antenna shall be mounted on the aircraft fuselage and will be behind a special radome to protect it from the external environment. All electronic equipment will be capable of being mounted within standard 19 inch racking which shall be assumed to be part of the aircraft equipment. Each equipment shall include its own power conditioners and any cooling fans which may be required for cooling. Alarm systems shall be provided in the event of the cooling fans failing. This alarm may be associated with an over temperature being measured. 3.3 Mass Properties
3.3.1 Mass
The overall mass shall be consistent with the budget provided in Table 3-1. This will not include infrastructure components of the aircraft such as the Radome, racking and Inertial Sensing Unit etc. 3.3.2 Mass Budget
The equipments shall meet the mass requirements as defined in the Table 3-1
Table 3-1 Mass Budget
Item Name Mass Budget (kg) Comments Up looking antenna 0.5 Navigation GPS
Receive 1
Signal Processor 18 Assumes hard-disc mass memory
Beam Former Receiver
8
Control Interface 5 Laptop PC 3 Multi Beam Array 27 Including Radome
and box
Inertial Sensing System
0 Not included in budget
Harness to Upward Looking antenna
2 Part of BFNRX
Main Electrical Harness
5
Harness to Multi beam array from
2 Part of BFNRX
COMMERCIAL IN CONFIDENCE
PARIS Aircraft Demonstrator
ENG.EP.EU.03.0117 Issue C
Page 10 of 29
EADS Astrium Ltd owns the copyright of this document which is supplied in confidence and which shall not be used for any purpose other than that for which it is supplied and shall not in whole or in part be reproduced, copied, or communicated to any person without written permission from the owner.
SP_0117_C GenRqts.doc
COMMERCIAL IN CONFIDENCE
RX Miscellaneous 10 Margin 10 15% Total 91.5 3.3.3 Centre of Gravity
Not applicable to the demonstrator 3.3.4 Moment of Inertia
Not applicable to the demonstrator 3.4 Electrical Requirements
3.4.1 General
The aircraft shall supply 28 Vdc from a regulated source. The suppliers shall assume that some further conditioning shall be required. Other supplies may be available. Each supplier shall provide power requirements for each of the major units. 3.5 Thermal Requirements
3.5.1 General
The internal thermal design of the unit shall be the responsibility of the unit supplier. The thermal design is based on the following conditions. The unit/ subsystem shall be designed in such a way that component and junction temperatures shall not exceed the de-rated allowables for space application when subjected to the Qualification environment interface temperatures. Material and processes shall not exceed their de-rated allowables when subjected to the qualification environment interface temperatures. The equipment will be mounted into standard 19 inch racking and cooling will be by forced air by means of electric fans within the equipments or racking. 3.5.2 Temperatures Limits
The unit/ sub-system temperature limits are defined in Table 3-2 Temperatures and are measured on the external structure of the relevant units/ sub-system. The environmental temperature of the air within the aircraft shall be as per Table 3-2. Internal
COMMERCIAL IN CONFIDENCE
PARIS Aircraft Demonstrator
ENG.EP.EU.03.0117 Issue C
Page 11 of 29
EADS Astrium Ltd owns the copyright of this document which is supplied in confidence and which shall not be used for any purpose other than that for which it is supplied and shall not in whole or in part be reproduced, copied, or communicated to any person without written permission from the owner.
SP_0117_C GenRqts.doc
COMMERCIAL IN CONFIDENCE
TEMPERATURE RANGE MINIMUM DEG C MAXIMUM DEG C Ambient +21 +23
Operating +0 +30 Acceptance -5 +35 Qualification Not applicable to the
demonstrator Not applicable to the
demonstrator Cold-switch-on -10 Non-operating -20 +55
Table 3-2 Unit/ Sub-system Temperature Requirements
These temperatures may not apply to the antenna if this is mounted outside of the aircraft in a non-pressurised radome. These temperatures will be in the range –80 to 50 deg C. 3.5.3 Thermal Finishes
Not relevant to the demonstrator 3.5.4 Cooling
The equipment will be mounted in a 19 inch rack assembly and the cooling will be in the form of forced cooling using electric fans. 3.5.5 Analysis
Sufficient analysis shall be carried out to ensure that all components and requirements stay within the specified temperatures. . 4. MECHANICAL DESIGN AND INTERFACES
4.1 General
The mechanical design shall be suitable for use in a pressurised or non-pressurised aircraft environment. The Antenna will be located behind a Radome which will be mounted in the lower part of the fuselage of the aircraft. Cables from this assembly will need to enter the cabin so it is expected that a special bulkhead will be required to pass the electrical connections from the cabin to the antenna.
COMMERCIAL IN CONFIDENCE
PARIS Aircraft Demonstrator
ENG.EP.EU.03.0117 Issue C
Page 12 of 29
EADS Astrium Ltd owns the copyright of this document which is supplied in confidence and which shall not be used for any purpose other than that for which it is supplied and shall not in whole or in part be reproduced, copied, or communicated to any person without written permission from the owner.
SP_0117_C GenRqts.doc
COMMERCIAL IN CONFIDENCE
60 deg Raydome
AntennaLNAs & Phase Shifters
Pressure BulkheadCables
RX
Processor
Mass Storage
Upwardlooking RX
Upward Looking Antenna
PowerConverter
AircraftSupply
115V 400Hz
28VdcController Man Machine Interface
BFN
Electronic Assembly
FixingsAnd
Av Mounts Cabin Floor
INS
Part of aircraftsystem
Part of aircraftsystem
60 deg Raydome
AntennaLNAs & Phase Shifters
Pressure BulkheadCables
RX
Processor
Mass Storage
Upwardlooking RX
Upward Looking Antenna
PowerConverter
AircraftSupply
115V 400Hz
28VdcController Man Machine Interface
BFN
Electronic Assembly
FixingsAnd
Av Mounts Cabin Floor
INS
Part of aircraftsystem
Part of aircraftsystem
Figure 4-1 Typical Configuration
The Figure 4-1 shows a typical aircraft configuration. The Downward looking antenna is mounted behind the Radome and the signals passed into the cabin where the beams are formed in the BFN and then passed to the Receiver and so on. The electrical assembly will contain the electronic circuits for the:
• Upward Looking GPS Receiver • Downward Looking Receiver • Signal Processor • Mass Storage (Part of Signal Processor) • Beam Forming Network • Instrument Control Unit
The controller may be a Laptop Pcin conjunction with an Interface Unit which is then connected to the Electronic Assembly The Electronic Assembly will contain the functions as described and this will be mounted to the aircraft via anti-vibration mounts if necessary. 4.1.1.1 Mechanical Analysis
Sufficient mechanical analysis shall be carried out to show that the equipment shall not cause any hazard once it is operated inside an aircraft. 4.1.1.2 Safety factors
To account for uncertainties of load factor evaluation, material data and analysis, as well as to avoid the influence of manufacturing inconsistencies, safety factors shall be applied as shown in Table 4-1.
FACTOR TYPE FACTOR REMARKS
Qualification factor (jQ) Limit loads x 1.25. Qualification test levels Yield Factor (jY) Qualification loads x 1.25 Avoids permanent deformation
Ultimate Factor (jU) Qualification loads x 2 Avoids failure by rupture or buckling
COMMERCIAL IN CONFIDENCE
PARIS Aircraft Demonstrator
ENG.EP.EU.03.0117 Issue C
Page 13 of 29
EADS Astrium Ltd owns the copyright of this document which is supplied in confidence and which shall not be used for any purpose other than that for which it is supplied and shall not in whole or in part be reproduced, copied, or communicated to any person without written permission from the owner.
SP_0117_C GenRqts.doc
COMMERCIAL IN CONFIDENCE
Insert Factor (jINS) Ultimate load x 1.5 For use in fixation insert design
Table 4-1 Applied Safety Factors
Notes on safety factors a) Failure resulting from local effects, e.g. stress concentration at cut-outs, inconsistencies of joining
elements shall be avoided by the application of an additional safety factor (jADD) to the qualification load. The use and magnitude of the factor shall be justified by prior experience or test data.
b) If the unit structure is verified by analysis only, then a factor of 1.25 for yield and 2 for ultimate load
conditions shall be applied to the qualification load. 4.1.1.3 Margin of safety
The unit shall be of adequate strength to withstand, without yielding or failing, all credible combinations of the specified loads and associated environment including assembly, integration, handling and transportation. All structural components shall have positive margins of safety (MS ≥ 0) for all load conditions and environments specified herein. 4.1.1.4 Evaluation of safety margins
For demonstration of the actual strength, a margin of safety evaluation is required. The evaluation shall be used in all cases of structural loading against surpassing the yield point and/or ultimate strength of materials as well as failure due to instability. The relevant surplus percentage has to be shown. The evaluation schematic is defined below:-
[ ]%100.1.
−=
σ
σ
jMs f
Where: σf = Material characteristics at failure point, eg material strength data,
Minimum value or critical instability data (allowables from material data sheet). σ = Maximum load/stress due to applied load. J = Relevant cumulative safety factor including jQ, jY, jU, jADD and jINS.
Material strength data for metal alloys as well as composites with a 99% statistical probability at a confidence level of 95% (A values) shall be used for MS evaluation. The long-term stability, moisture absorption and creep effects shall be considered appropriately. In case of bonded joints and composite materials, which have high strength variation due to the manufacturing process, the relevant design criteria shall be respected. The special failure modes, such as de-lamination, shall be avoided by application of the relevant failure criteria, design principles and product assurance activities.
COMMERCIAL IN CONFIDENCE
PARIS Aircraft Demonstrator
ENG.EP.EU.03.0117 Issue C
Page 14 of 29
EADS Astrium Ltd owns the copyright of this document which is supplied in confidence and which shall not be used for any purpose other than that for which it is supplied and shall not in whole or in part be reproduced, copied, or communicated to any person without written permission from the owner.
SP_0117_C GenRqts.doc
COMMERCIAL IN CONFIDENCE
4.1.1.5 Material design allowable
Material strengths and other mechanical and physical properties shall be selected from authorised sources of reference, such as British Standards, and from contractor test values when appropriate. Strength allowables and other mechanical properties used shall be appropriate to the loading conditions, design environments and stress states for each structural member. Allowable material strengths used in design shall include the effects of temperature and time associated with the design environment. 4.1.1.6 Failure modes
The unit shall withstand all anticipated loads and environments without experiencing failures as defined in Table 4-2
FAILURE MODE ALLOWED ABOVE YIELD LOAD ULTIMATE LOAD Rupture X Instability (Global Buckling) X Yielding X Excessive elastic deformations (exceedance of allowed clearances)
X
Gapping of bolted connections X
Table 4-2 Structural Failure Modes
For verification of gapping, the maximum friction coefficient shall be used. For stress analyses of fasteners, the minimum friction coefficient shall be used. This requirement applies for the determination of pre-torque moments of bolts/screws in the thread. Limit load = design load exclusive of any safety factors. 4.1.1.7 Design loads
The mechanical environment shall be as defined for vibration and shock as defined in 4.3. 4.2 Operability
4.2.1 Reliability
4.2.1.1 Assessed Reliability
Not relevant to demonstrator 4.2.1.2 Single Point Failure
Not relevant to demonstrator 4.2.2 Safety
A safety assessment shall be carried out and potential hazards identified.
COMMERCIAL IN CONFIDENCE
PARIS Aircraft Demonstrator
ENG.EP.EU.03.0117 Issue C
Page 15 of 29
EADS Astrium Ltd owns the copyright of this document which is supplied in confidence and which shall not be used for any purpose other than that for which it is supplied and shall not in whole or in part be reproduced, copied, or communicated to any person without written permission from the owner.
SP_0117_C GenRqts.doc
COMMERCIAL IN CONFIDENCE
4.2.2.1 Product Safety
Shall be compliant with the requirements of air safety. The equipment is expected to reside in a pressurised cabin so they should not be subjected to the extremes of environments. However, vibration, shock, temperature and reductions in pressure will be experienced. In the case of the antenna it may reside outside of the pressurised cabin so its pressure and temperature environment will be more severe. 4.2.3 Useful Life
The PADS shall be capable of operating for up to 5 hrs in one operation. The use of the PADS shall be in a semi-operational manner. For the purpose of this program the life can be assumed to be up to two years with a flight frequency of up to once per week. TBC. The equipment may be used between missions for test purposes up to 7 hours per day for up to once per week over the life. 4.3 Environment
4.3.1 On-Ground Mechanical Environment
4.3.1.1 Transportation and Handling loads
The unit transportation container and MGSE will be exposed to dynamic loads during road and air transportation and ground handling operations. The loads are defined for the load bed of the transportation vehicle. Transportation and handling the loads shall be applied as defined in Table 4-3. For handling operations the following loads shall be considered: Shock: equivalent to a fall from 100mm height when one edge of the Unit container remains on the ground. 4.3.1.2 MGSE Loads
The MGSE and transportation container shall be designed to limit the loads at the centre of gravity of the unit to less than the values defined in Table 4-4 when subjected to the environment specified in this specification
OPERATION X (+ AFT)
Y (+ STBD)
Z (+ UP)
REMARKS
(g) Scalar value Handling ± 1.0 ± 0.75 +2.0 / -0.7 Road Transport ± 1.1 ± 1.2 -3.0 / +1.0 Quasi-static Air Transport ± 1.5 ± 1.5 +2.2 / -1.5 Ship Transport ± 0.3 ± 0.5 +1.8 / -0.4 For MGSE only Transport shock load ± 4g (for a saw tooth form of 20 milliseconds duration)
Table 4-3 Limit Accelerations for Ground Operations
(Unattenuated Worst Case Input to MGSE)
COMMERCIAL IN CONFIDENCE
PARIS Aircraft Demonstrator
ENG.EP.EU.03.0117 Issue C
Page 16 of 29
EADS Astrium Ltd owns the copyright of this document which is supplied in confidence and which shall not be used for any purpose other than that for which it is supplied and shall not in whole or in part be reproduced, copied, or communicated to any person without written permission from the owner.
SP_0117_C GenRqts.doc
COMMERCIAL IN CONFIDENCE
OPERATION X (+ AFT)
Y (+ STBD)
Z (+ UP)
REMARKS
(g) Scalar value Handling ± 1.0 ± 0.75 +2.0 / -0.7 Road Transport ± 0.8 ± 0.8 ± 2.0 Quasi-static Air Transport ± 1.5 ± 1.5 +2.2 / -1.5 Ship Transport ± 0.3 ± 0.5 +1.8 / -0.4 For MGSE only Transport shock load ± 1.5 ± 1.5 ± 2.0
Table 4-4 Limit Accelerations for Ground Operations
(Worse Case Input Allowables to Unit)
4.4 Design and Construction
4.4.1 General
The design and construction shall take into account to purpose of the demonstration and the need to produce an instrument which will be installed onto an aircraft. On the basis that the instrument will be used periodically then the installation and de-installation shall be considered during the design. 4.4.2 Venting Provisions
Provision shall be made for adequate venting of the internal free air space of the unit, in order to maintain internal and external pressure equilibrium. As a guideline the venting apertures should be less than 1.5mm diameter and have a depth to diameter ratio of at least 3:1. Typical thermal vacuum conditions of ≥ 1 x 10-5
Torr may be experienced. 4.4.3 Mounting Provisions
To be compatible with mounting in a 19 inch rack. The interface shall be agreed with the customer. 4.4.4 Parts, Materials and Processes
4.4.4.1 Parts
All critical parts used in the design of the unit shall be declared in a parts list. 4.4.4.2 Materials
All critical materials shall be declared in a materials list. 4.4.4.3 Processes
All critical processes shall be declared in a processes list. 4.4.5 Moisture and fungus resistance
Moisture traps shall be avoided. Parts and materials that may deteriorate when exposed to the climatic and environmental conditions during storage or service usage shall be protected against such deterioration.
COMMERCIAL IN CONFIDENCE
PARIS Aircraft Demonstrator
ENG.EP.EU.03.0117 Issue C
Page 17 of 29
EADS Astrium Ltd owns the copyright of this document which is supplied in confidence and which shall not be used for any purpose other than that for which it is supplied and shall not in whole or in part be reproduced, copied, or communicated to any person without written permission from the owner.
SP_0117_C GenRqts.doc
COMMERCIAL IN CONFIDENCE
Materials, which are not nutrients for fungi, shall be used wherever practicable. Where nutrient materials have to be used outside of hermetically sealed containers, such materials shall be treated with fungicidal agent. Qualification of a particular composition shall be determined by test method 508 of MIL-STD-810, environmental test methods. 4.4.6 Corrosion prevention and control
4.4.6.1 Corrosion resistance
The design shall include provisions for corrosion prevention and control. Materials used shall resist damage from moisture, with particular emphasis on parts that lose their protective coatings during normal course of inspection, maintenance and periodic testing. 4.4.6.2 Dissimilar metals
The use of dissimilar metals shall be controlled in accordance with MIL-STD-889, dissimilar metals. 4.4.6.3 Protective treatments
Any materials used in the construction of the unit that may be subjected to deterioration when exposed to the climatic and environmental conditions likely to occur during any phase of the programme, shall be protected against such deterioration. Particular attention shall be paid to earth bonding requirements where bonding is achieved through the unit-mounting interface 4.4.6.4 Coatings and adhesives
Coatings and adhesives shall be capable of withstanding the environmental conditions defined in this specification without performance degradation. 4.4.7 Identification and marking
Each unit furnished under this specification shall be marked with a unique visual identification code. This shall not affect any aspect of the performance. 4.4.8 Documents and standards
Documentation used in the design, manufacture and test of the unit shall conform to general configuration requirements. Drawings and other documents required for the manufacture and test of the unit shall be listed in the unit drawing tree. All design and manufacturing standards and techniques shall be approved by the customer. Any change from the approved baseline shall only be implemented following formal configuration control procedure. 4.5 Electro-Magnetic Compatibility
TBD
COMMERCIAL IN CONFIDENCE
PARIS Aircraft Demonstrator
ENG.EP.EU.03.0117 Issue C
Page 18 of 29
EADS Astrium Ltd owns the copyright of this document which is supplied in confidence and which shall not be used for any purpose other than that for which it is supplied and shall not in whole or in part be reproduced, copied, or communicated to any person without written permission from the owner.
SP_0117_C GenRqts.doc
COMMERCIAL IN CONFIDENCE
4.5.1 Bonding & Isolation
TBD 5. VERIFICATION, CERTIFICATION AND TEST
5.1 General Requirements
The design, manufacture and test of the PADS shall be verified as specified in this section by using established company standards, methods and procedures. The testing for certification for airworthiness shall be carried out as defined in the following sections. The supplier shall propose a series of analyses and testing based on the requirements of this specification. 5.1.1 Responsibility for Tests
The Supplier shall be responsible for all tests. 5.1.2 Airworthiness testing (reference AD2)
The PADS shall be designed to meet the environment as specified in RTCA/DO-160D to the extent defined in this document. It shall be required to provide Qualification according to the above referenced specification. The environments and testing shall be in accordance with the following table.
Conditions Section of RTCA/DO-160D
Category Required
Description of Tests to be Conducted for Qualification
Temperature and Altitude
4.0 through to 4.6.3
A1 Equipment Temperature range within Cabin assumed to be 0 to 55deg C at minimum Cabin Pressure equivalent to 4600m (170 kPa). It is possible that the Antenna could see a more severe range if it is not contained within the Cabin TBD. Emergency depressurisation is not required
Temperature Variation 5.0 C Internal Cabin. The Antenna may see more sevre environment if outside the Cabin (Category A)
Humidity 6.0 A Operational Shock and Crash Safety
7.0 A No requirement for Crash Safety testing is assumed
Vibration 8.0 Standard Vibration –
Sine or Random
Shock Analysis or test may be applicable
See 5.2.2.2 of this specification
Explosion 9.0 Not applicable
Waterproofness 10.0 Not applicable
COMMERCIAL IN CONFIDENCE
PARIS Aircraft Demonstrator
ENG.EP.EU.03.0117 Issue C
Page 19 of 29
EADS Astrium Ltd owns the copyright of this document which is supplied in confidence and which shall not be used for any purpose other than that for which it is supplied and shall not in whole or in part be reproduced, copied, or communicated to any person without written permission from the owner.
SP_0117_C GenRqts.doc
COMMERCIAL IN CONFIDENCE
Fluids susceptibility 11.0 Not applicable
Sand and Dust 12.0 Not applicable
Fungus 13.0 Not applicable
Salt spray 14.0 Not applicable
Magnetic Field 15.0 Not applicable
Power Input 16.0 Not applicable
Preferred approach is that a regulated supply is already provided onboard so this test will have been covered by the Certification of the regulator which will be part of the aircraft
Voltage spike 17.0 Not applicable
Preferred approach is that a regulated supply is already provided onboard so this test will have been covered by the Certification of the regulator which will be part of the aircraft
Audio Frequency Susceptibility
18.0 Not applicable
This is associated with ac power supplies which will not be used
Induced Signal Susceptibility
19.0 Not applicable
Covered by design of the equipment and will not influence the aircraft
Radio Frequency Susceptibility
20.0 S Reduced level
Radio Frequency Emissions
21.0 U
Lightning Induced Transient Susceptibility
22.0 TBC May need to demonstrate survival under these conditions. But not performance
Lightning Direct Effects
23.0 Not applicable
Icing 24.0 Electrostatic Discharge
25.0
Other Tests 5.1.3 Certification for Airworthiness
The PADS shall be qualified for aircraft operations. The equipment shall be designed to meet the defined environments and a Environment Qualification Form provided as evidence according to the requirements of RTCA/DO-160D. The following is a typical requirement for meeting the airworthiness requirements. In the event the actual requirements will need to be agreed with the airworthiness authority who may require some adjustments to the requirements as defined in this specification. However, the stated requirements shall be used for the purposes of the proposed project.
COMMERCIAL IN CONFIDENCE
PARIS Aircraft Demonstrator
ENG.EP.EU.03.0117 Issue C
Page 20 of 29
EADS Astrium Ltd owns the copyright of this document which is supplied in confidence and which shall not be used for any purpose other than that for which it is supplied and shall not in whole or in part be reproduced, copied, or communicated to any person without written permission from the owner.
SP_0117_C GenRqts.doc
COMMERCIAL IN CONFIDENCE
5.2 Testing
5.2.1 Test Conditions
5.2.1.1 Ambient Test Conditions
1. Unless otherwise specified in the applicable test, all test shall be performed under ambient conditions, which are:
a. Temperature +22±3 deg C b. Pressure 96 to 103.5 kPa c. Relative Humidity 35 to 60% 5.2.1.2 Tolerance of Test Parameters
The maximum allowable tolerance for test parameters shall be as follows unless otherwise specified within this specification. The tolerance specifies the allowable range within which the specified test level may vary and is exclusive of instrument accuracy. a. Temperature Maximum -0, +3 deg C Minimum -3, 0 deg C Tolerance between
Max and Min ±3 deg C
b. Barometric
Pressure
>=100Pa ±10% <100Pa and >0.04Pa ±50% <0.04 Pa ±80% c. Relative
Humidity ±5%
d. Acceleration ±10% e. Vibration
Frequency ±2% or ±1Hz
whichever id the least
f. Sinusoidal Amplitude
±10%
g. Sweep Rate ±5%
h. Random Vibration Acceleration
Power Spectral Density
20 to 500Hz ±1.5 dB
>500Hz ±3.0 dB Random
overall g rms ±1%
i. Force ±5% j. Weight ±1 g k. Dimensions ±0.123 mm l. COG
measurements ±0.5 mm
m. MOI measurements
±0.05kgm2
COMMERCIAL IN CONFIDENCE
PARIS Aircraft Demonstrator
ENG.EP.EU.03.0117 Issue C
Page 21 of 29
EADS Astrium Ltd owns the copyright of this document which is supplied in confidence and which shall not be used for any purpose other than that for which it is supplied and shall not in whole or in part be reproduced, copied, or communicated to any person without written permission from the owner.
SP_0117_C GenRqts.doc
COMMERCIAL IN CONFIDENCE
n. Time ±3% 5.2.1.3 Temperature Stabilisation
The rate of change of temperature shall not change by more than 5 deg/ minute. 5.2.2 Testing for Airworthiness
5.2.2.1 Vibration
5.2.2.1.1 Fixture
The transmission and cross-talk between axes of the test fixture when loaded by the test article shall be determined prior to the formal tests. The transmission amplification shall not exceed ±3 dB and the cross-talk between axes shall not exceed the input. 5.2.2.1.2 Sine Survey
The objective of this test is to verify that no unexpected resonance’s have occurred due to design or issues associated with manufacture and quality. The conditions for the test shall be as follows: a. Amplitude 0.5g zero to peak b. Frequency Range 5 Hz to 2 kHz c. Sweep Rate 2 octaves/ minute d. Direction X, Y and Z axes e. Equipment state Non-operating 5.2.2.1.3 Random Vibration
5.2.2.1.3.1 General
The standard vibration tests, as defined in RTCA/DO-160D, shall demonstrate that equipment will meet its functional performance requirements during normal operating conditions of the aircraft. 5.2.2.1.3.2 Procedure for The Random Vibration Test
In each of the equipment's three orthogonal axes, perform the following test sequence:
a. Performance a sine survey
b. With the equipment operating, apply the appropriate performance level test Acceleration Power Spectral Density (APSD) for a minimum of one-hour-per-axis to DETERMINE COMPLIANCE WITH APPLICABLE EQUIPMENT PERFORMANCE STANDARDS. During this vibration period, also perform an APSD analysis of the vibration response measurements on the equipment. The levels shall be as defined in Figure 5-1.
c. Repeat the sine survey. Any changes in vibration resonant frequencies shall be noted on the environmental Qualification form . At the completion of the test, the equipment shall be inspected and shall show no evidence of structural failure of any internal or external component.
COMMERCIAL IN CONFIDENCE
PARIS Aircraft Demonstrator
ENG.EP.EU.03.0117 Issue C
Page 22 of 29
EADS Astrium Ltd owns the copyright of this document which is supplied in confidence and which shall not be used for any purpose other than that for which it is supplied and shall not in whole or in part be reproduced, copied, or communicated to any person without written permission from the owner.
SP_0117_C GenRqts.doc
COMMERCIAL IN CONFIDENCE
Figure 5-1 Standard Random Vibration Test Curves for Equipment installed in Fixed Wing Aircraft with Turbojet of Turbofan Engines
5.2.2.2 Shock Tests
5.2.2.2.1 Purpose of the Tests
The operational shock test verifies that the equipment will continue to function within performance standards after exposure to shocks experienced during normal aircraft operations. These shocks may occur during taxiing, landing or when the aircraft encounters sudden gusts in flight. This test applies to all equipment installed on fixed- wing aircraft and helicopters. Two operational shock test curves are provided; a standard 11 msec pulse and a low frequency 20 msec pulse. The 20 msec shock is applicable to very rough runways and will not be relevant to this mission. The 11 msec shock level shall be applied as the equipment is regarded as Category A.
Appropriate Level is Level
COMMERCIAL IN CONFIDENCE
PARIS Aircraft Demonstrator
ENG.EP.EU.03.0117 Issue C
Page 23 of 29
EADS Astrium Ltd owns the copyright of this document which is supplied in confidence and which shall not be used for any purpose other than that for which it is supplied and shall not in whole or in part be reproduced, copied, or communicated to any person without written permission from the owner.
SP_0117_C GenRqts.doc
COMMERCIAL IN CONFIDENCE
5.2.2.2.2 Test Procedure
Secure the equipment to a shock table by means of a rigid test fixture and mounting means intended for use in service installations. The mounting of the equipment should include those non-structural connections that are a normal part of the installation. The accelerometer used to measure or control the input shock pulse shall be placed as close as practicable to an equipment attachment point. With the equipment operating and with its temperature stabilized, apply to the test item three shocks in each orientation having a terminal saw-tooth wave shape with an acceleration peak value of six (6) g’s. The nominal pulse duration shall be 11 ms for standard shock testing. The characteristics of instrumentation used to demonstrate compliance and the shock pulse tolerance limits are shown in Figure 5-2and Figure 5-3, respectively. An equivalent shock response spectrum may replace the terminal saw-tooth wave shape. After application of the shocks, DETERMINE COMPLIANCE WITH APPLICABLE EOUIPMENT PERFORMANCE SPECIFICATION. When using a conventional drop shock machine, the equipment shall be shock tested in the following orientations:
a. Normal upright. b. Suspended upside down. C. At orientations such that the first major orthogonal axis of the equipment successively forms angles of +90 degrees and -90 degrees (two orientations) with the plane of the table. d. At orientations such that the second major orthogonal axis of the equipment successively forms angles of +90 degrees and -90 degrees (two orientations) with the plane of the table.
Figure 5-2 Shock Measuring system Frequency Response
COMMERCIAL IN CONFIDENCE
PARIS Aircraft Demonstrator
ENG.EP.EU.03.0117 Issue C
Page 24 of 29
EADS Astrium Ltd owns the copyright of this document which is supplied in confidence and which shall not be used for any purpose other than that for which it is supplied and shall not in whole or in part be reproduced, copied, or communicated to any person without written permission from the owner.
SP_0117_C GenRqts.doc
COMMERCIAL IN CONFIDENCE
Figure 5-3 Terminal Saw-tooth Shock Pulse Configuration and its Tolerance Limits
5.2.2.3 Temperature and Altitude Testing
5.2.2.3.1 Purpose of Test
These tests determine the performance characteristics of equipment at the applicable categories for the temperatures and altitudes. 5.2.2.3.2 Category
The Category shall be A1 Equipment intended for installation in a controlled temperature and pressurized location, on an aircraft within which pressures are normally no lower than the altitude equivalent of 15,000 ft (4,600 m) Mean Sea
Level (MSL), is identified as Category A1 . This category may also be applicable to equipment installed in temperature controlled but unpressurized locations on an aircraft that operates at altitudes no higher than 15,000 ft (4,600 m) MSL.
COMMERCIAL IN CONFIDENCE
PARIS Aircraft Demonstrator
ENG.EP.EU.03.0117 Issue C
Page 25 of 29
EADS Astrium Ltd owns the copyright of this document which is supplied in confidence and which shall not be used for any purpose other than that for which it is supplied and shall not in whole or in part be reproduced, copied, or communicated to any person without written permission from the owner.
SP_0117_C GenRqts.doc
COMMERCIAL IN CONFIDENCE
5.2.2.3.3 Test Procedure
The temperature test has been designed to combine several individual tests. The tests include:
• Cold storage • Cold switch-on • Cold Operation • Hot storage • Hot operation • Temperature variation • Cooling failure
5.2.2.3.4 Thermal Tests
Thermal environment tests shall be carried out under following conditions and those as defined below:
1. Pressure: Atmospheric ambient 2. Relative Humidity: (purge with dry Nitrogen for cold)
Ambient
High-Operational
High Storage-non-operational
Low -Operational
Low StorageNon operational
Cooling Failure Test
10 deg/Min
10 deg/Min
10 deg/Min
operational
10 deg/Min
operational
Stab3hrs
Non-op
Stab3hrs
Non-op
Stab3hrs
Non-op
Stab3hrs
Non-op
Stab3hrs
Non-op
Stab
Stab3hrs
Non-op
Stab3hrs
Non-op
1 hroperational
ColdSwitch-on
3hrsoperational
3hrsoperational
10 deg/minoperational
A
B C
D E F
G H
J K L
M N P
Q R S
T U V30mins
Ambient
High-Operational
High Storage-non-operational
Low -Operational
Low StorageNon operational
Cooling Failure Test
10 deg/Min
10 deg/Min
10 deg/Min
operational
10 deg/Min
operational
Stab3hrs
Non-op
Stab3hrs
Non-op
Stab3hrs
Non-op
Stab3hrs
Non-op
Stab3hrs
Non-op
Stab
Stab3hrs
Non-op
Stab3hrs
Non-op
1 hroperational
ColdSwitch-on
3hrsoperational
3hrsoperational
10 deg/minoperational
A
B C
D E F
G H
J K L
M N P
Q R S
T U V30mins
Figure 5-4 Thermal Test Cycle Profile
Figure 5-4 defines the temperature testing profile. 5.2.2.3.5 Altitude Test
Conduct this test at ambient temperature. Operate the equipment at maximum duty cycle. Decrease the pressure in the test chamber to the appropriate maximum operating altitude specified in m. This will be 12000m (TBC) Allow the equipment temperature to stabilize. Maintain this pressure for at least two hours. Determine compliance of the equipment performance during the two-hour period or at the maximum duty cycle, whichever is longer. The test profile is shown graphically in Figure 5-5
COMMERCIAL IN CONFIDENCE
PARIS Aircraft Demonstrator
ENG.EP.EU.03.0117 Issue C
Page 26 of 29
EADS Astrium Ltd owns the copyright of this document which is supplied in confidence and which shall not be used for any purpose other than that for which it is supplied and shall not in whole or in part be reproduced, copied, or communicated to any person without written permission from the owner.
SP_0117_C GenRqts.doc
COMMERCIAL IN CONFIDENCE
Figure 5-5 Altitude Test
5.2.2.3.6 Decompression Test
This test is not required as the equipment does not have to perform correctly during an emergency descent. 5.2.2.3.7 Power Supply Test
The electrical supplies used will be special to the Sensor and will be separate from the Aircraft systems. Hence, these tests will be carried out as part of the functional testing of the Sensor. 5.2.2.3.8 Voltage Spikes
As per 5.2.2.3.7 5.2.2.3.9 Audio Frequency Audio Susceptibility
As per 5.2.2.3.7 5.2.2.3.10 Induced Frequency Susceptibility
As the system is not part of the aircraft system and the harnesses will be separate from the aircraft system this test is not required. 5.2.2.3.11 Radio Frequency Susceptibility
This should not be high as the sensor will be placed in the cabin area of an all metal aircraft. The test levels are TBD
COMMERCIAL IN CONFIDENCE
PARIS Aircraft Demonstrator
ENG.EP.EU.03.0117 Issue C
Page 27 of 29
EADS Astrium Ltd owns the copyright of this document which is supplied in confidence and which shall not be used for any purpose other than that for which it is supplied and shall not in whole or in part be reproduced, copied, or communicated to any person without written permission from the owner.
SP_0117_C GenRqts.doc
COMMERCIAL IN CONFIDENCE
5.2.2.3.12 Emission of Radio Frequency Energy
The Equipment is not designed to transmit. The modules will be contained in screened housings so any EMC testing will be carried out at Sensor level. 5.2.2.3.13 Lightning induced Transient Susceptibility
This is not relevant to this equipment 5.2.2.3.14 Lightning Direct Effects
This is not relevant to this equipment 5.2.2.3.15 Electrostatic Discharge
This is not relevant for airworthiness and will be addressed at equipment level 5.2.2.3.16 EMC Tests
The EMC requirements shall be as defined in the Mil-Std-461E ( AD1) and according to the Table 5-1.
Table 5-1 EMC Applicability Matrix
Requirement ApplicabilityEquipment/
Subsystems installed on aircraft
A L A S S A A A A A Where A is applicable L is limited according to the Mil-Std-461E S is specific to project needs TBD 6.
COMMERCIAL IN CONFIDENCE
PARIS Aircraft Demonstrator
ENG.EP.EU.03.0117 Issue C
Page 28 of 29
EADS Astrium Ltd owns the copyright of this document which is supplied in confidence and which shall not be used for any purpose other than that for which it is supplied and shall not in whole or in part be reproduced, copied, or communicated to any person without written permission from the owner.
SP_0117_C GenRqts.doc
COMMERCIAL IN CONFIDENCE
INTENTIONALLY BLANK
COMMERCIAL IN CONFIDENCE
PARIS Aircraft Demonstrator
ENG.EP.EU.03.0117 Issue C
Page 29 of 29
EADS Astrium Ltd owns the copyright of this document which is supplied in confidence and which shall not be used for any purpose other than that for which it is supplied and shall not in whole or in part be reproduced, copied, or communicated to any person without written permission from the owner.
SP_0117_C GenRqts.doc
COMMERCIAL IN CONFIDENCE
DOCUMENT CHANGE DETAILS
ISSUE CHANGE AUTHORITY CLASS RELEVANT INFORMATION/INSTRUCTIONS
A II First issue
B II Minor amendments
DISTRIBUTION LIST
INTERNAL
EXTERNAL
ESTEC
top related