dissertation maija
Post on 14-Apr-2017
356 Views
Preview:
TRANSCRIPT
Abstract
Fuel and energy demand is high in the 21st century, however the non-renewable energy resources are
becoming scarcer. Biofuels are developing as a potential substitute for conventional fuels and waste coffee
grounds is one of the novel resources that offers feedstock for biofuel obtainment. Coffee oil contains lipids,
which contain fatty acid methyl esters (FAME). FAME is – biodiesel. There are two types of coffee beans.
Arabica (Coffea Arabica) and Robusta (Coffea Canephora). Arguably, the more expensive Arabica coffee
beans give more lipid content, hence more biodiesel than blends (Arabica and Robusta). This theory was
tested when spent coffee grounds were acquired from Starbucks, Costa and Nero coffee houses. Starbucks
uses 100% Arabica coffee beans, whereas Costa uses a blend (70% Arabica and 30% Robusta). Nero uses a
blend of the two types of coffee beans, although the exact percentage is not known. Spent coffee grounds
were obtained from six different coffee houses of 3 brands (Starbucks, Costa, and Nero). With a yield of
0.93 g and 1.6 g of biodiesel per 10 g of spent coffee grounds acquired from Starbucks, the evidence was
found to support the statement that Arabica beans give more biodiesel than the blends. In comparison, waste
coffee grounds obtained from Costa gave 0.18 g and 0.37 g of biodiesel. Nero gave 0.33 g and 0.25 g of
biodiesel. It was also decided to determine the feasibility of the obtained biodiesel by analysing samples
using an infra-red spectroscopy analysis. During the analysis it was found that all samples contained fatty
acid methyl esters (FAME). This finding provided evidence that obtained substance was biodiesel and that it
had the same compound as biodiesel previously obtained by other researchers.
Acknowledgements
The author would like to thank Dr Roy Lowry for suggesting this topic as well as helping with the progress
of the research and also mention and thank The University of Plymouth 5th floor Davy Building laboratory
technicians. Especially Andrew Tonkin for his great help with the laboratory research part of this project,
Claire Williams, Rebecca Sharp and Louise Argent for their cooperation.
1
Table of Contents
Chapter 1. Introduction_______________________________________________________________4
Chapter 2. Literature Review__________________________________________________________5
Chapter 3. Methodology______________________________________________________________9
Chapter 4. Research Findings, Results, and Discussion______________________________________17
Chapter 5. Conclusions, Research Limitations, and Suggestion for Future Research_______________26
References_________________________________________________________________________29
Appendix A. Biodiesel Sample Photographs and a Scanned Lab. Book Page_____________________37
Appendix B. Sample Infra-Red Graphs Before Transesterification_____________________________41
Appendix C. Excel Data Analysis_______________________________________________________47
Appendix D. Energy Input Calculations__________________________________________________48
Appendix E. Scanned Laboratory Book__________________________________________________50
Appendix F. COSHH and Risk Assessment_______________________________________________64
2
List of Figures
Figure 1___________________________________________________________________________18
Figure 2___________________________________________________________________________19
Figure 3___________________________________________________________________________20
Figure 4___________________________________________________________________________21
Figure 5___________________________________________________________________________22
Figure 6___________________________________________________________________________23
Figure 7___________________________________________________________________________24
3
Chapter One. Introduction
As early as in 1926, American inventor-Samuel Morey took out a patent for the engine that used alcohol and
turpentine as fuel (Masum et al., 2015). In 1953 it was stated that vegetable oil can potentially be used as
fuel in steam engines and steamships (Demirbas, 2009). Notably, the first operational steam engine was
powered by coal (Spear, 2008). The first four-cycle internal-combustion engine was created by a German
engineer-Nikolaus August Otto and it was powered by ethanol. Interestingly, various modifications of this
engine are still used these days (Churchward, 2009). In the beginning of the 19th century Rudolf Diesel has
built an engine, he fuelled with peanut oil (Dunn and Knothe, 2001). The reason Rudolf Diesel substituted
coal dust with peanut oil was simply because it offered more safety. Biodiesel has a higher flash point than
conventional diesel fuel and is less explosive (Muniyappa, Brammer and Noureddini, 1996). Henry Ford
worked with engines fuelled by alcohol until the 1940s (Kovarik, 1998). In 1908 he used ethanol to fuel his
Model T Ford (Reitze, n.d.). In the beginning of the 40s the Second World War started. Hard-to-reach areas
did not get enough fuel supply and had to use vegetable oils to power diesel engines (Sidibé et al., 2010).
Approximately 40 years ago in 1973 the world experienced dramatic rise in oil prices (Voudouris, 2014). In
the 1986 oil prices collapsed (Gately, Adelman and Griffin, 1986). However, today in the 21st century oil
prices rise again due to the declining amount of oil reserves that can be accessed easily (Burkart and
Mayfield, 2013). Promptly, a need for new renewable energy sources arises (Johansson and Burnham,
1993). Biodiesel is one of such sources. Bio - meaning life from Greek - and Diesel coming from Rudolf
Diesel refers to fuel made of vegetable oil or animal fat (Tan, Abdullah and Nolasco-Hipolito, 2015). These
days, biodiesel is especially widely used in Germany, where annually 3.5 billion litres are produced. In Italy
the number is 1.2 billion litres/year and France – 1 billion litres per year (Воронков, 1999). Biodiesel is
blended with the conventional diesel fuel. This reduces greenhouse gas emissions by 70% (Фелленберг,
1997). Spent coffee grounds – as a potential biodiesel source were chosen to be a topic of this research
project. Other types of biodiesel sources, such as: rapeseed oil, palm oil, sunflower-seed oil, and cottonseed
oil are often mentioned in the wider literature (Германович and Турилин, 2014). However biodiesel
obtained from waste coffee grounds is a relatively new approach. This research project looks into its’
4
benefits and drawbacks, as well as, the differences in the coffee bean type. There are approximately 6
million tons of coffee produced annually (Haile, 2014). According to (Ching et al., 2011), 45% of waste sent
to landfills in Malaysia is made of waste that has spent coffee in it. Waste coffee sludge is also problematic
to dispose of (Rathinavelu and Graziosi, 2005). Its’ moistness as well as the presence of proteins, sugars,
and inorganic matter results in a rapid growth of microorganisms (Fujii and Takeshi, 2007). Hence, if it is
not immediately processed it puts the surrounding environment under the risk of contamination (Vardon et
al., 2013). Waste coffee grounds dumped to landfills contribute to a higher carbon footprint (Noponen et al.,
2012). Carbon footprint (CO2e) stands for the total amount of greenhouse gases emitted (Shrestha et al.,
2012). As stated by (Ching et al., 2011), burning 1000 g of coffee produces 538 g of CO2. However, there is
a chance that waste can prove to be valuable instead of being detrimental to the environment. In 2014 a
company called Bio-bean was established in London. Bio-bean acquires spent coffee grounds from local
coffee houses and turns them into biodiesel to be utilized as fuel and biomass pellets to be used for heating
buildings (bio-bean, 2016). There are two main types of coffee: Arabica (Coffea Arabica) and Robusta
(Coffea Canephora). Arabica is more expensive than Robusta and has a higher commercial value (Dias and
Benassi, 2015). Current research project aimed at determining how much biodiesel it is possible to obtain
from Arabica beans and blends (Arabica and Robusta), as well as looking into the feasibility aspect of the
obtained biodiesel. This study highlighted the importance of researching alternative energy and fuel sources.
Thus, it is significant because in the times of a constant search for new resources (Винокурова and
Трушин, 1998) it is very timely.
Chapter two. Literature Review
Inflationary pressure, resource deterioration, and rising greenhouse gas emissions that amplify CO2
concentrations and entail further climate change, urge the modern society to consider biofuel as a potential
source of clean and renewable energy and fuel (Guo, Song and Buhain, 2015). Resource deterioration issue
is highly relevant to such conventional energy source as oil. According to (Fantazzini, Höök and
Angelantoni, 2011), most oil these days is almost out of reach, whereas extracting oil from existing oil wells
requires tremendous financial and energy inputs due to the necessity of using specific equipment and
technology. In the 21st century, energy demand is as high as ever (Гринин and Новиков, 2002). When
5
inputs into fuel obtainment are bigger than the outputs, it does not only make the fuel economically
unviable, but also stimulates greenhouse gas emissions (Han et al., 2015). This is especially relevant to the
oil and gas industry. A large amount of energy is required to produce fuels made of hydro-carbons, such as
crude oil and gas. This threatens energy security and environmental sustainability. Hydro-carbons demand
high energy inputs and fuel based on hydro-carbons contributes to greenhouse gas emissions into the
atmosphere (IPIECA, 2013). Still, the consumption rates hence the dependence on crude oil is very high
nowadays. If current demands for this resource fail to diminish, the society will only have approximately 45
years before its depletion (Guo, Song and Buhain, 2015). This interlinks with other reasons listed above, to
come up with a novel way of producing fuel. One of such novel, renewable resources is biofuel. Most
biofuels used today are first-generation biofuels. First-generation biofuels are generally produced from food
sources such as, grain, vegetable oil etc. (Mohr and Raman, 2013). There are various types of plants that can
be used for oil extraction. One of the most widely used is rapeseed oil. The advantage of it is a high
tolerance to different climate conditions and soil types. In contrast, palm oil, is a very effective resource due
to its high oil yield (Luque, 2010). However, it lacks such good adaption to diverse conditions and has its’
cloud point at 16 ºC and pour point at 15 ºC (Dunn, 2011). Cloud point is the temperature at which the
crystallization of the fuel occurs (IMAHARA, MINAMI and SAKA, 2006). Pour point usually occurs at
lower temperatures than cloud point and is the lowest fuel pouring/flowing temperature (Veríssimo and
Gomes, 2011). For this reason Asian countries, where climate is mild and warm, represent its main market.
The drawback of other types of energy crops such as flaxseed and sunflower, is their high value as a food
source. Continually increasing demand for new renewable energy and fuel sources results in energy crops
competing with food crops. The outcome of such competition is the increase in food price and decrease in
its availability, whereas the demand for it grows with growing numbers of the Earths’ population.
Encouraging energy crops to compete with food crops could be socially inadmissible (Luque, 2010). Thus,
flaxseed and sunflower situation accentuates the fact that efficiency and practicality of potential biofuel
sources are not only identified by their oil and biomass yield, it is also important to consider whether other
uses of the resource are more commercially, politically, environmentally and socially significant (White and
Plaskett, 1981). Despite a number of controversies regarding the sustainability and energy-efficiency of
first-generation biofuels, policies released by the governments continue to involve biofuel use. In addition to
6
the food crop competition controversy, mentioned above, another issue is that emissions that come from
crop cultivation account for 80% of total greenhouse gas emissions that originate from biofuel obtained
from plants (Hennecke et al., 2013). These issues have developed a surge of second-generation biofuels
research (Montross, 2010). Second-generation biofuels are mainly obtained from straw, wood chippings,
hay, agricultural forestry residues and other residual waste (Sims et al., 2010). (Grover, Grover and
Hogland, 2002) state that the main goal of waste to energy proposals are “…to maximize combustion and
minimize pollution”. (Gupta and Demirbas, 2010) noted that oil obtained from waste is a crucial resource,
nevertheless it is only marginally utilized due to the lack of the resource supply. However, referring to
waste, the article did not mention spent coffee grounds. Spent coffee grounds are a good example of the
second-generation source for biodiesel production. According to (Caetano et al., 2014) coffee market is a
growing market. The amount of annually consumed coffee on a global level was quantified as 16.34 billion
pounds and the amount of waste per 1g of cofee is 0.91g (Kondamudi, Mohapatra and Misra, 2008).
Therefore more than 90% of coffee waste is being sent to a landfill. Considering all mentioned above, spent
coffee grounds could prove to be a reasonable second-generation alternative to first-generation biofuels.
This statement presents the importance of this potential fuel source to be studied. The literature review of
this study is based on the two questions identified as the most important ones to this research project. The
first question asked whether the bean type, Arabica (coffea arabica) or Robusta (coffea canephora) impact
the amount of biodiesel obtained. Approximately 90% of the coffee produced worldwide is made of the
expensive Arabica coffee beans. Less tasty and cheaper Robusta coffee beans account for only 9% of the
worldwide coffee production (El-Abassy, Donfack and Materny, 2011). The second question this research
project investigated is whether it is feasible to use biodiesel obtained from spent coffee grounds. The
literature review focused on the search for answers to these questions in the literature. The concept of the
hypothesis of this research project was that spent coffee grounds from Starbucks gives more biodiesel, than
Costa or Nero. This hypothesis was based on a theory that Arabica beans, which are used in Starbucks
coffee, have a higher lipid content than Robusta beans. Notably, both Costa and Nero use a blend of Arabica
and Robusta. This theory about differences in the lipid content was derived from the statement made by
(Jenkins et al., 2014). Although it is important to note that the article also mentioned that the difference
between the lipid content was not significant between pure Arabica and a blend (Arabica and Robusta).
7
Lipid content is important, because it contains glycerides which, when transesterified, produce biodiesel
(Jenkins et al., 2014). Transesterification is a reaction used to produce esters and in this study is used to
produce biodiesel from the glyceride portion of the coffee oil content (Otera, 1993). Interestingly, after
performing a spectroscopy analysis, (Rubayiza and Meurens, 2005) have also stated that dry roasted Arabica
beans have 16.8% and Robusta 11.5% of lipid content. In the research, studying coffee oils, done by (Ferrari
et al., 2010) it was also clearly stated that green Arabica coffee beans have 15% of the lipid content
compared to Robusta having only 10%. It was apparent after the review of the literature, that although pure
Arabica beans are said to have a higher lipid content, hence give more biodiesel than pure Robusta, it was
either stated that the blends of the two are not significantly different from Arabica, for example by (Jenkins
et al., 2014), or the blends were not mentioned at all. The second question of this research project asked if
it’s feasible to use biodiesel obtained from the waste coffee grounds. A few of the previously done studies
focused on the feasibility of biodiesel made from coffee grounds. (Kondamudi, Mohapatra and Misra, 2008)
for example claimed biodiesel obtained from spent coffee grounds to be a high quality substitute to diesel.
(Murthy and Madhava Naidu, 2012) have also agreed on the feasibility of the biodiesel made of coffee,
stating that the solid content of spent coffee grounds, left after oil extraction, is perfect for fertilization and
can also be used as biomass pellets and ethanol feedstock. In relation to this it is noteworthy to mention that
the company called “Bio-Bean” is already obtaining biodiesel from spent coffee grounds and utilizing solid
waste left after oil extraction as biomass pellets to use in boilers (Smedley, 2014). There were a few studies
conducted in relation to the biodiesel obtainment from spent coffee grounds. However, in the literature
about biofuels in general, an apparent tendency of excluding spent coffee grounds as a potential biofuel
source has been observed. It could have been suggested that such trend exists due to the chosen literature
being outdated, with the oldest source reviewing coffee as a biodiesel resource being published in 1996.
However, there were newer books referenced in the current report, which were published in 2010 and 2011.
Therefore, it can be assumed that spent coffee grounds have not yet been widely considered as a potential
biofuel resource. Hence, it can also be proposed that this particular resource has not been well researched to
this point in time and in order to reduce the possibility of exhaustion of alternative sources, it is vital to
invest in, promote, and persist with the further research of surrogate biofuel sources (Fisheries and Food,
1996). Hence, this research project aims at demonstrating an importance of coffee as a potential second-
8
generation biodiesel source. Through centuries, coffee has been disliked by the rulers of countries it has
been introduced to. It has been banned by the Koran in Arabic countries. The government in London in the
17th century suspected that it was consumed in areas where mutineers gathered. At the same time in France
the government tried to impose high taxes on the beverage due to its inconvenient concurrence with wine
industry. Nevertheless, coffee has always been popular among all nations and social categories, no taxes or
prohibitions could intervene with its highly valued repute (Flament and Bessiere-Thomas, 2002). Coffee is
still one of the global favourite beverages (Li, Strezov and Kan, 2014). These facts suggest that it might be a
long time before the popularity of the drink decreases, therefore there will always be valuable coffee waste.
This enhances the chances of this resource utilization to achieve success.
Chapter three. Methodology
Introduction
Upon the theoretical perspective of the current issue, it is now fundamental to provide convincing arguments
that would justify the use of the chosen methodology. It is also necessary to demonstrate how the selected
research approach aligns with the issue under consideration. The main purpose of this methodology chapter
is to give a detailed description of how the research was conducted and data obtained in order to present the
evidence base and support for the arguments. The structure of the methodology chapter in the current piece
of work begins with the description of the research design chosen for this dissertation, as well as the
research questions. The next section will talk about the validity and reliability of the data obtained, looking
into the laboratory methods, equipment and analytical approaches. A brief description of the two locations,
first, where the samples were collected and second where the samples were analysed will follow.
Subsequently, a very detailed section with a precise description of samples, materials and methods will be
written to be thereafter followed by the conclusion summarising the key arguments of this methodology.
Research Design and Research Questions (Aims and Objectives)
Already at the planning stage, it was evident that this study will follow the quantitative approach.
Representing a vital constituent of the science studies, the skill of quantitative analysis plays an important
role in the science degree (Ling and Bridgeman, 2011). As mentioned by (Hoe and Hoare, 2012), in regards
9
to nursing, quantitative analysis might potentially present a new possibility of choosing an appropriate
treatment approach. Additionally, due to a wide variety of data available via online sources these days, the
ability of correctly interpreting the clinical data by the medical personnel is vital to provide valuable advice
to the patient. In relation to this study, the abundance of modern-day environmental issues results in a large
number of people being deeply concerned about the environment. However the richness of often inaccurate
data available via online sources gives rise to multiple misconceptions that the concerned but incompetent
general public acquires (Walz and Kerr, 2007). Logically, this enhances the need of environmental scientists
to train in quantitative research in order to develop the ability to recognize both strengths and limitations of
data (Vaccaro, Smith and Aswani, 2010). This argument presents a strong support for the quantitative
research method chosen for the current research project. Being a relatively new approach, biodiesel
obtainment from waste coffee grounds is subject to many questions, therefore it is critical not only to state
the theoretical reasons to support it but also to underpin it with evidence derived from both primary and
secondary data. This dissertation has adopted an inductive approach. It is aimed at testing the theory that
Arabica coffee beans give a significantly higher lipid content than Robusta coffee beans (Ferrari et al.,
2010). As stated by (Jenkins et al., 2014) the glyceride portion of oil that produces biodiesel via
transesterification is present in lipids in 80-95%. Therefore, it was hypothesized that Starbucks coffee beans
which, according to the official Starbucks website (Starbucks Coffee Company, 2016) consist of 100% pure
Arabica beans would give a higher biodiesel yield than Costa that uses a blend of Arabica and Robusta
(Costa.co.uk, 2016) and Nero that also blends Arabica beans with Robusta (Caffenero.co.uk, 2016). In order
to test the hypothesis, a series of laboratory experiments on Starbucks, Costa, and Nero waste coffee
grounds were conducted. Thus, the amount of biodiesel obtained from each coffee house was determined.
The feasibility of the obtained biodiesel from each coffee house was also examined, using infrared
spectroscopy. Thus, this research project had two objectives. The primary objective of the study was to
demonstrate that a higher biodiesel yield can be obtained from Starbucks waste coffee grounds, which use
100% Arabica than from Costa and Nero, which use a blend of Arabica and Robusta. The rationale behind
this objective was to obtain spent coffee grounds from all three houses and perform a series of experiments
to obtain biodiesel. The secondary objective was to understand whether it is feasible to use the biodiesel
obtained from the three coffee houses. In turn, the rationale behind this objective was to examine the
10
chemical composition of the compounds of biodiesel from the three coffee houses, using the Brucker
infrared atomic absorption spectrometer. By performing infrared spectroscopy analysis it became possible to
compare the obtained biodiesel to findings retrieved from the literature in order to see if it would be feasible
to utilize it.
Data and Sample Collection and Analysis
In regard to the chosen settings, the crucial part was the choice of the same three coffee houses-Costa,
Starbucks and Nero, but located in 6 different stores. This approach was chosen in order to test the
homogeneity of coffee beans used by the same brand but in different shops. Hence, two different Starbucks
coffee houses were chosen, one at the Drake Circus shopping centre, another located on Armada Way
Street. This was also done to Nero coffee with one sample obtained from Cornwall Street and one from
Debenhams on Royal Parade. Costa coffee samples were acquired from Drake Circus shopping centre and
University of Plymouth campus. The conditions, coffee grounds were brewed under were uncontrolled, due
to the grounds being acquired from the shop after brewing. Coffee grounds from all three coffee houses
were of mixed content (caffeinated with decaffeinated), the amounts represented by each type are unknown.
Spent coffee grounds (SCGs) were warm and humid. On the grounds that this research project deals with
organic chemistry, to analyse the collected samples, organic chemistry laboratory number 501 in Davy
Building at the University of Plymouth was used for the most procedures of the current experiment. Such
equipment as the rotary evaporator Buchi Rotavapor R-300 and reflux apparatus electromantle EM0500/CE
were used during the process of biodiesel obtainment. There are several laboratory techniques that can be
used to obtain biodiesel from spent coffee grounds. Pyrolysis is one of them. Pyrolysis is a process of
keeping the organic mass heated in the absence of oxygen. Since oxygen is a neccessary requirement in
order for combustion to occure, the organic material does not burn (Ars.usda.gov, 2010). Instead, the
process of decomposition follows and results in two products bio-oil and char. The advanced product of bio-
oil is biodiesel (Montross, 2010). (Li, Strezov and Kan., 2014) who have used pyrolysis to obtain bio-oil and
other pyrolysis products, have found that pyrolysis improves the elemental composition of bio-oil. (Bok et
al., 2012), however noted that the obtainment of biodiesel from waste coffee grounds via pyrolysis has not
yet been widely studied. In spite of pyrolysis being extensively applied in current worldwide research, it
11
has its drawbacks. There is a lack of cost competitive capacity of the pyrolysis process when it is applied to
biomass and waste (Bridgwater, 2003). Another way to obtain biofuel is through transesterification. During
transesterification the oil is separated from glycerine, resulting in biodiesel and saponifiable substances
(Biodiesel.org, 2015). The benefit of transesterification process is its ability to lower the viscosity of
biodiesel. The high viscosity of the oil content of biodiesel presents the major issue of biodiesel obtained
from biomass oils. The reduction of viscosity by transesterification improves the functioning of biodiesel
(Gupta and Demirbas, 2010). Thus, the transesterification process was chosen as a technique to obtain
biodiesel in the current research project. The entire sequence of the laboratory processes used to obtain
biodiesel through transesterification is:
1. Stirring dried coffee grounds and an added solvent
2. Mixing methanol with sulfuric acid
3. Transesterification
4. Separation of methyl esters(biodiesel) and saponifiable substances (Biodiesel.org, 2015)
5. Washing biodiesel to remove methanol, glycerol and acid catalyst (Jenkins et al., 2014)
Before and after transesterification, Bruker alpha-p FI-IR Spectrometer was used to analyse the samples.
Infrared spectroscopy is a technique used to show types of mixtures and their amount in a compound
(McKelvy et al., 1998). These characteristics can be obtained from observing a phenomenon called
stretching vibrations of bonds. When a range of infrared frequencies are shone through the compound a
number of frequencies get absorbed by the compound. Energy from these absorptions results in the
appearance of the bond stretches, which in their turn indicate what mixture and in what amount is present in
the compound (McKelvy et al., 1998). The appliance of infrared spectroscopy technique to analyse samples
correlates well with the chosen research type. In his book from 1963, Rao states that infrared spectroscopy
appears to be supreme in relation to other techniques for both qualitative and quantitative analyses. In the
end of the analysis, graphs with peaks were produced by a computer. Interpretation of these graphs allows
scientists to analyse samples and determine what compounds and in what amounts are inside the
samples (Stuart, 2004).
12
Data Validity and Reliability
Data validity and reliability is an important tool to make the research a subject of consideration and
convince the public to place confidence in the obtained results (Ekstedt et al., 2014). Unlike qualitative
research, quantitative research focuses on the internal validity of the chosen research methods rather than
general trustworthiness of the study (Appleton, 2006). Therefore in order to determine validity and
reliability of the obtained data, laboratory research techniques and equipment should be examined as well as
the chosen software for the data analysis. Due to a range of different equipment used and a high number of
other experiments conducted using the same equipment, the risk of sample contamination was present.
According to (EnviroMatrix Analytical, Inc., n.d.) laboratories often work with small-scale samples and at
this level contamination can easily occur. Whereas (Smith, 2000) states that all laboratories encounter this
issue and even though it is regarded as unavoidable, it can however be minimized by keeping laboratories
clean. Other simple methods, such as wearing gloves and using wipes will help prevent sample
contamination (EnviroMatrix Analytical, Inc., n.d.). In the current experiment all mentioned above was
abided by. In order to avoid contamination fresh heptane was also used after the rotary evaporation. Same
equipment such as syringes, spatulas etc. was never used with different substances. Also, not only validity
and reliability of equipment and laboratory conditions should be examined. Microsoft Excel 2013 was
chosen as a software for data analysis. As stated by (Odeh, Featherstone and Bergtold, 2010), Excel 2007
shown greater reliability than the previous versions of the software, however minor problems were still
encountered in their research of the software credibility. It was also mentioned that full trust into the
software reliability might result in the potential generation of false and biased deductions (Odeh,
Featherstone and Bergtold, 2010). However, in regard to the current study it can be assumed that Excel
software has improved throughout years and the newer version used for this research provided more
credibility during data analysis. Although, no legitimate proof was found to support this statement. Infrared
spectroscopy is widely used in science and is a reliable technique to identify organic mixture compounds
(Shipman et al., 2013). In comparison to some previously conducted studies, this research has used the same
laboratory equipment as both (Jenkins et al., 2014) and (Zannikos et al., 2011). Interestingly, the same
13
laboratory methods, such as transesterification and equipment, as well as infrared spectroscopy, were not
only used for extracting biodiesel from coffee, but also for the biodiesel obtainment from frying oil,
described by (Leung and Guo, 2006). This might suggest the relative credibility of data obtained and
analysed using these methods.
Materials and Methods
The current research project used a mixed method research. Both primary and secondary data were used in
order to support the arguments and objectives stated in methodology. Secondary data was obtained from a
variety of sources available as scientific papers and books. Primary data was collected from three local
coffee houses located in Plymouth-Costa, Starbucks and Nero. The first sample of spent coffee grounds was
obtained from Starbucks café at Drake Circus shopping mall, Plymouth, UK. Spent coffee grounds (SGSs)
were put into ceramic plates and put into the 67 degree Celsius oven for 24 hours to dry. After exactly 24 h
of drying, the ceramic plates with dried spent coffee ground from were removed from the oven and put into
2 1L plastic containers. 10 g of SCGs were put into a pre-weighed conical glass flask. In a fume cupboard
100 ml of fresh heptane (solvent), accurately measured with a beaker were added to the flask along with a
stirrer bar. Subsequently the flask was put on an electro-magnetic stirrer, a stirring power of 7 was chosen
and the solution was left to stir in a room temperature in a fume cupboard for exactly 180 minutes. After the
stirring process was stopped the stirred content of the flask was filtered into a pre-weighed round bottom
glass flask, using a 110 mm Whatman filter paper and a 7cm glass funnel. To the solid content left after
filtering another 100 ml of fresh heptane was added and left to stir for another 180 minutes in a room
temperature in a fume cupboard. The liquid from the first filtration was put into a rotary evaporator at 40 °C.
Heptane evaporated and oil was left in the flask. Oil obtained from the first extraction was weighed.
Meanwhile, the content in the conical flask left after the second stirring was filtered into a pre-weighed
round bottom glass flask, using a 110mm Whatman filter paper and 7cm glass funnel. Subsequently, the
filtered substance was put into a rotary evaporator at 40 °C for heptane to evaporate. Oil obtained from the
second extraction was weighed. Oil from both extractions was combined together in one round bottom glass
flask. Oil from both extractions was analysed using a Bruker alpha-p FI-IR Spectrometer. A droplet of oil
was put on the diamond surface of the machine in order to analyse the sample. Transesterification reaction
14
followed: 9.5 g of methanol is added to the round bottom glass flask with the oil from both extractions.
Thereafter 0.17 g of sulphuric acid was added to the flask (roughly 10th of the weight ratio of the oil). Then
the flask with its’ content was put in a fume cupboard to reflux for 24h. Substance was filtered into a pre-
weighed 100 ml round bottom glass flask (r.b.f.), using a 110 mm Whatman filter paper and a 7cm glass
funnel. Whatman paper is weighed in order to determine the amount of unsaponifiable material later in the
process. Methanol was added to the flask to help remove the unsaponifiable material sticking to it and
transfer it into the filter. The flask with unsaponifiable material sticking to it was weighed. The pre-weighed
filter paper was left inside the 40 °C oven for a few days. Filtered substance was transferred into the rotary
evaporator. Methanol evaporated. Hence, only the needed material (biodiesel) and sulphuric acid were left
in the r.b.f. In order to get rid of the sulphuric acid, the flask was washed with 25 ml of diethyl ether
anhydrous into a separating funnel. Subsequently, the flask was washed with water three times and all that
put into the separating funnel as well. In the separating funnel, liquid to liquid extraction technique was
performed to get rid of all the waste material (water and sulphuric acid). The oily substance was then
transferred into a pre-weighed r.b.f. During the transfer, bits of the oily content was left in the separating
funnel. Then, 6 spoons of sodium sulphate anhydrous were added to the flask with biodiesel and ether in
order to dry the flask content. Substance was left to stay and dry for 10 minutes. The substance was then
filtered into another round bottom glass flask. The flask was put into a rotary evaporator and ether
evaporated, leaving only biodiesel in the flask. The biodiesel was weighed. After the biodiesel obtainment
another infrared spectroscopy analysis was performed, using a Bruker alpha-p FI-IR Spectrometer.
Meanwhile, the filter paper with unsaponifiable material was removed from the oven and weighed.
Previously measured weight of unsaponifiable material from the flask was combined with the weight of
unsaponifiable material from the dried filter paper and counted. Next, a sample of waste coffee grounds
acquired from Costa coffee house located on the University of Plymouth campus, another Starbucks sample
taken from the same container as the first sample and waste coffee ground sample obtained from Nero on
Cornwall Street underwent the same procedure as the first Starbucks (Drake) sample. Spectroscopy analysis
was done before and after the transesterification. Then new samples, obtained from Nero (Debenhams),
Starbucks (Armada Way) and Costa (Drake Circus) and a sample from an old container of Nero (Cornwall
Street) followed the same procedure as the previous waste coffee ground samples. As usual all samples were
15
analysed before and after the transesterification using the spectroscopy analysis. The Starbucks (Armada
Way) sample experiment was done on a bigger scale. 100 grams of waste coffee grounds from Starbucks
(Armada Way) were taken and 1 litre of heptane. After first extraction another litre of fresh heptane was
added. 16 ml of concentrated sulphuric acid and 50 g of methanol were added before reflux. Then 250 ml of
Diethyl Ether Anhydrous were used to wash the substance into the separating funnel.
Conclusion
Both practical and literary techniques chosen for this work proved to be concise and easy to follow. Good
research facilities and an easy access to sources explaining the laboratory procedures used contributed to a
well-structured and planned research project. The experience obtained from the use of the chosen laboratory
methods was compared to the methods used in the literature and validity of results was determined via these
comparisons.
16
Chapter four. Research Findings, Results and Discussion
Research Finding and Results
This research project has adopted a quantitative, rather than a qualitative research technique. Hence, order to
comply with the hypothesis and the objectives, this section of the study demonstrates the results produced in
the forms of statistical analysis. In order to analyse the obtained data, Microsoft Excel 2013 was used. The
hypothesis of this research project stated that spent coffee grounds obtained from Starbucks give more
biodiesel than spent coffee grounds obtained from Costa and Nero. Even though more research is required
in order to prove the hypothesis, this study gave evidence that the hypothesis was supported. Figure 1 shows
the amount of biodiesel obtained from 10 grams of each sample of spent coffee grounds acquired from six
coffee shops of three different brands. Starbucks gave the most biodiesel content, yielding in 0.93 g and 1.6
g of biodiesel. Costa gave 0.18 g and 0.37 g of biodiesel. Nero gave 0.33 g and 0.25 g of
biodiesel .Photographs of the biodiesel samples obtained and a scanned copy of the laboratory book page,
describing the laboratory procedure and the results can be found in the Appendix A.
17
Fig. 1
Starbucks (Drake Circus)
Starbucks (Armada Way)
Costa (University Campus)
Costa (Drake Circus) Nero (Debenhams) Nero (Cornwall Street)
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
Biodiesel per 10g of SCGs (g)
Figure 1. Comparison of biodiesel obtained from 10 g of spent coffee grounds from 6 coffee shops
The Pearson’s correlation test was performed on the data obtained at the laboratory. It was found that r= .9.
In order to support the second objective and find out whether the biodiesel obtained would be feasible to
use, infrared spectroscopy analysis was performed on all samples before and after transesterification.
Spectroscopy graphs showing biodiesel samples analysed after transesterification reaction can be seen
below. Figure 2 shows Starbucks (Drake Circus), figure 3-Costa (University Campus), figure 4-Nero
(Cornwall Street), figure 5-Costa (Drake Circus), figure 6-Nero (Debenhams), and figure 7 demonstrates
Starbucks (Armada Way) biodiesel samples.
18
Fig. 2
Figure 2 showing the Starbucks (Drake Circus) biodiesel sample on the infra-red spectroscopy graph
19
Fig. 3
Figure 3 showing the Nero (Debenhams) biodiesel sample on the infra-red spectroscopy graph
20
Fig. 4
Figure 4 showing the Costa (Drake Circus) biodiesel sample on the infra-red spectroscopy graph
21
Fig. 5
Figure 5 showing the Nero (Cornwall Street) biodiesel sample on the infra-red spectroscopy graph
22
Fig. 6
Figure 6 showing the Costa (University Campus) biodiesel sample on the infra-red spectroscopy graph
23
Fig. 7
Figure 7 showing the Starbucks (Armada Way) biodiesel sample on the infra-red spectroscopy graph
Spectroscopy graphs that show the samples before transesterification processes can be found in the
Appendix B. Two Excel tables showing the Medium amount of the obtained biodiesel and the Pearson’s
correlation value between the amount of biodiesel obtained and the percentage of Arabica beans used, can
be seen in the Appendix C. The mean amount of biodiesel produced among all samples was found to be
24
0.61 g. In this research project calculations have been made to determine the amount energy invested in
order to extract biodiesel from 10 grams of spent coffee grounds. To see a scanned copy of the complete
energy input calculations refer to the Appendix D. It was found that in order to obtain the mean amount of
diesel, 0.61 g, 22200 kJ of energy input is required. In order to see the full copy of the laboratory book see
the Appendix E.
Discussion
The main objective of this research project was to give evidence that more lipid content can be obtained
from Arabica than Robusta coffee beans. This would support the hypothesis that Starbucks waste coffee
grounds, which are 100% Arabica beans (Starbucks Coffee Company, 2016) can be used to extract more
biodiesel than Costa (Costa.co.uk, 2016) and Nero (Caffenero.co.uk, 2016), who use a blend of Arabica and
Robusta. Lipid content contains glycerides. When alcohol is added to glycerides, transesterification reaction
occurs and fatty acid methyl esters (FAME) are created. FAME- is biodiesel (Sawangkeaw, Bunyakiat and
Ngamprasertsith, 2010). In contrast to the (Jenkins et al., 2014) method, it was decided to conduct
experiments for this research project on a small scale. The statistical analysis of all biodiesel samples
obtained during the current research project shows that there is a strong positive correlation between using
Arabica beans in order to obtain biodiesel and the amount of biodiesel obtained. Pearson’s correlation test
gave a value of .9. Therefore, it can be stated that there is evidence that Arabica beans give more biodiesel
than a blend of Arabica and Robusta. The amount of biodiesel is closely related to the amount of the lipid
content in the beans. (Jenkins et al., 2014) stated that the lipid content contains glycerides, of which
biodiesel is made, when transesterified. Therefore, there is support for the theory that more lipid content can
be obtained from Arabica, rather than Robusta coffee beans. The second objective was to show that it is
feasible to use biodiesel obtained from waste coffee grounds. The rationale behind this objective was to
analyse biodiesel samples using infrared spectroscopy and compare it to the infrared analysis of biodiesel in
the literature. The spectroscopy graphs of samples on figure 2-6 are relatively similar, showing low
transmittance carboxylic acid peaks (Practical Infra-Red Spectroscopy, 2002) at 2922 and 2853 on figure 2,
2923 and 2853 on figure 3, 2922 and 2853 on figure 4, 2923 and 2853 on figure 5, as well as, 22923 and
2853 on figure 6. Biodiesel sample on figure 7, however, is different. Its’ peak is of a similar transmittance
25
(around 60%) as samples 2-6, but the frequency is 3389. Due to its’ difference from 5 other samples, it was
considered anomalous and omitted from the discussion. According to (Lewis and Evans, 2006) fatty acids
are carboxylic acids with long hydrocarbon chains. Therefore it can be said that fatty acids are present in
biodiesel samples from all 5 coffee shops. Starbucks (Armada Way) is omitted in the current statement due
to its’ peak being abnormal. (Zannikos, Anastopoulos and Deligiannis, 2011) in their research found that
coffee oil has such fatty acids as: Palmitic, Stearic, Oleic, Linoleic and Arachidic. According to (Jenkins et
al., 2014) fatty acids methyl esters (FAME) is what is called biodiesel. Therefore, due to carboxylic acid
peaks being found in the samples, it can be said that infrared spectroscopy proved that biodiesel was
obtained during this research work. As stated by (Jenkins et al., 2014) if it is blended following the right
recommendations, biodiesel can be used in both U.S.A. and Europe. This statement gives evidence to the
second objective of this report-feasibility of the obtained biodiesel. Finally, after calculating the energy
input, needed to conduct the laboratory procedures and obtain biodiesel, it must be stated that even though
the mean amount of biodiesel produced is 0.61 g, Starbucks spent coffee grounds gave a significantly bigger
amount of biodiesel than Costa and Nero, even though the energy input at the laboratory was the same.
Overall it can be said the chosen methodology aligned well with the expected results.
Chapter five. Conclusions, Research Limitations and Suggestions for Future Research
Conclusions
Waste coffee grounds contain oil that is mainly comprised from such fatty acid methyl esters (FAME) as
linoleic acid, palmitic acid (35-40%), (44-50%), oleic acid (7-8%) and stearic acid (7-8%) (Bendall et al.,
2015). FAME are produced via the transesterification reaction, which occurs when triglycerides contained
in the coffee oil react with alcohol (Ault and Pomeroy, 2012). FAME are biodiesel (Jenkins et al., 2014).
However, it was stated by (Ferrari et al., 2010) that Arabica beans give more lipid content than Robusta
coffee beans. This research project aimed at finding whether it is the case with Arabica beans compared to
blend of Arabica and Robusta. It was found that Arabica coffee beans in fact do give more lipid content that
blends. The support for this statement was found via the hypothesis that Starbucks waste coffee grounds
would give more biodiesel, hence contain more lipids than a Costa and Nero waste coffee grounds, The
reason for such comparison was the fact that Starbucks uses 100% Arabica, whereas Costa and Nero both
26
use blends of Arabica and Robusta. Costa is known to use 70% Arabica beans and 30% Robusta, whereas
the blend percentages in Nero are not known. From 10 g of waste coffee grounds acquired from two
Starbucks stores, 0.93 g and 1.6 g of biodiesel were obtained. 10 g of waste coffee grounds from Costa gave
0.18 g and 0.37 g. 10 g of Nero resulted in 0.33 g and 0.25 g. The Pearson’s correlation test showed a strong
positive correlation between Arabica beans and the amount of biodiesel obtained. Thus, the evidence for the
hypothesis that Arabica beans give more biodiesel than blends was found. Hence, the hypothesis supported
the theory that Arabica beans contain more lipids that Robusta coffee beans. Also, the evidence to support
the statement that the obtained biodiesel would be feasible to use was found via infrared spectroscopy
analysis, which determined the presence of fatty acid methyl esters (FAME) in the analysed samples of the
obtained biodiesel. With references to the literature findings of FAME reported before, it was determined
that there was evidence for the biodiesel obtained during this research project to prove to be feasible. In
addition, energy input required to obtain biodiesel from the coffee samples was calculated. Energy
throughput of the laboratory procedures required to produce biodiesel was the same for all samples.
However, Arabica beans used by Starbucks gave more biodiesel, while using the same amount of energy.
Therefore strong positive correlation between using Arabica coffee grounds and obtaining a bigger amount
of biodiesel is an evidence that it is more efficient to use spent coffee grounds from Starbucks.
Research Limitations and Suggestions for Future Research
The current research was limited by the amount of time devoted to it being less than a year. Therefore, for
the future research done on this topic, it can be suggested to explore such properties of biodiesel as: density
and kinematic viscosity. During this study, energy input required to produce biodiesel was found. However,
it can be suggested to also find the energy output of the obtained biodiesel. It can also be suggested to find
the energy input required to produce conventional diesel fuel and compare the inputs.
27
28
References
Abdullah, M. and Bulent Koc, A. (2013). Oil removal from waste coffee grounds using two-phase solvent
extraction enhanced with ultrasonication. Renewable Energy, 50, pp.965-970.
Appleton, J. (2006). Analysing qualitative interview data: addressing issues of validity andreliability.
Journal of Advanced Nursing, 22(5), pp.993-997.
Ars.usda.gov, (2010). Sustainable Biofuels and Co-Products : What Is Pyrolysis?. [online] Available at:
http://www.ars.usda.gov/Main/docs.htm?docid=19898 [Accessed 4 Nov. 2015]
Ault, A. and Pomeroy, R. (2012). Quantitative Investigations of Biodiesel Fuel Using Infrared
Spectroscopy: An Instrumental Analysis Experiment for Undergraduate Chemistry Students. J. Chem.
Educ., 89(2), pp.243-247.
Bendall, S., Birdsall-Wilson, M., Jenkins, R., Chew, Y. and Chuck, C. (2015). Showcasing Chemical
Engineering Principles through the Production of Biodiesel from Spent Coffee Grounds. J. Chem. Educ.,
92(4), pp.683-687.
bio-bean. (2016). About Us - bio-bean. [online] Available at: http://www.bio-bean.com/about-us/ [Accessed
18 Apr. 2016].
Biodiesel.org, (2015). Biodiesel Basics - Biodiesel.org. [online] Available at: http://biodiesel.org/what-is-
biodiesel/biodiesel-basics [Accessed 4 Nov. 2015].
Bok, J., Choi, H., Choi, Y., Park, H. and Kim, S. (2012). Fast pyrolysis of coffee grounds: Characteristics of
product yields and biocrude oil quality. Energy, 47(1), pp.17-24.
Breithaupt, J. (2010). Physics. 3rd ed. London: Palgrave McMillian, p.159.
Bridgwater, A. (2003). Pyrolysis and gasification of biomass and waste. Newbury, UK: CPL Press.
Burkart, M. and Mayfield, S. (2013). Biofuels for the 21st century. Current Opinion in Chemical Biology,
17(3), pp.436-438.
29
BГњCHI Labortechnik AG, (2015). RotavaporВ® R-300 Operation Manual. Version B. Flawil: BГњCHI
Labortechnik AG, p.20.
Caetano, N., Silva, V., Melo, A., Martins, A. and Mata, T. (2014). Spent coffee grounds for biodiesel
production and other applications. Clean Techn Environ Policy, 16(7), pp.1423-1430.
Caffenero.co.uk. (2016). CaffГЁ Nero. [online] Available at: http://www.caffenero.co.uk/default.aspx
[Accessed 7 Apr. 2016].
Ching, S., Yusoff, M., Aziz, H. and Umar, M. (2011). Influence of impregnation ratio on coffee ground
activated carbon as landfill leachate adsorbent for removal of total iron and orthophosphate.Desalination,
279(1-3), pp.225-234.
Churchward, M. (2009). Gas Engines in Victorian Industry, 1870-1950.
Costa.co.uk. (2016). The Nation's Favourite Coffee Shop | Costa Coffee. [online] Available at:
http://www.costa.co.uk [Accessed 7 Apr. 2016].
Cruz, R., Mendes, E., Torrinha, Á., Morais, S., Pereira, J., Baptista, P. and Casal, S. (2015). Revalorization
of spent coffee residues by a direct agronomic approach. Food Research International, 73, pp.190-196.
Demirbas, A. (2009). Progress and recent trends in biodiesel fuels. Energy Conversion and Management,
50(1), pp.14-34.
Dias, R. and Benassi, M. (2015). Discrimination between Arabica and Robusta Coffees Using Hydrosoluble
Compounds: Is the Efficiency of the Parameters Dependent on the Roast Degree?.Beverages, 1(3), pp.127-
139.
Dogmore, T. (2015). The Business of Food Waste.
DUNN, R. and KNOTHE, G. (2001). Alternative Diesel Fuels from Vegetable Oils and Animal
Fats.Journal of Oleo Science, 50(5), pp.415-426.
30
Dunn, R. (2011). Improving the Cold Flow Properties of Biodiesel by Fractionation.
Eia.gov. (2015). How many gallons of diesel fuel and gasoline are made from one barrel of oil? - FAQ -
U.S. Energy Information Administration (EIA). [online] Available at:
https://www.eia.gov/tools/faqs/faq.cfm?id=327&t=9 [Accessed 5 Apr. 2016].
Ekstedt, N., Wallnerstrom, K., Babu, S., Hilber, P., Westerlund, P., Jurgensen, J. and Lindquist, T. (2014).
Reliability Data – A Review of Importance, Use, and Availability. 2.5.
Electrothermal.com. (2016). EM Electromantles. [online] Available at:
http://www.electrothermal.com/product.asp?dsl=750 [Accessed 5 Apr. 2016].
El-Abassy, R., Donfack, P. and Materny, A. (2011). Discrimination between Arabica and Robusta green
coffee using visible micro Raman spectroscopy and chemometric analysis. Food Chemistry, 126(3),
pp.1443-1448.
EnviroMatrix Analytical, Inc., (n.d.). Understanding Types and Sources of Sample Contamination. San
Diego: EnviroMatrix Analytical, Inc., pp.1-2.
Fantazzini, D., Höök, M. and Angelantoni, A. (2011). Global oil risks in the early 21st century. Energy
Policy, 39(12), pp.7865-7873.
Ferrari, M., Ravera, F., De Angelis, E., Liverani, F. and Navarini, L. (2010). Interfacial properties of coffee
oils. Colloids and Surfaces A: Physicochemical and Engineering Aspects, 365(1-3), pp.79-82.
Fisheries and Food, M. (1996). The National Biomass Energy Strategy. [Manuscript] University of
Plymouth Library, PB2544. Plymouth.
Flament, I. and Bessiere-Thomas, Y. (2002). Coffee flavor chemistry. Chichester: Wiley.
Fujii, K. and Takeshi, K. (2007). Penicillium strains as dominant degraders in soil for coffee residue, a
biological waste unsuitable for fertilization. Journal of Applied Microbiology, 103(6), pp.2713-2720.
Gately, D., Adelman, M. and Griffin, J. (1986). Lessons from the 1986 Oil Price Collapse. Brookings
Papers on Economic Activity, 1986(2), p.237.
31
Grover, V., Grover, V. and Hogland, W. (2002). Recovering energy from waste. Enfield, NH: Science
Publishers.
Guo, M., Song, W. and Buhain, J. (2015). Bioenergy and biofuels: History, status, and
perspective. Renewable and Sustainable Energy Reviews, 42, pp.712-725.
Gupta, R. and Demirbas, A. (2010). Gasoline, diesel, and ethanol biofuels from grasses and plants. New
York: Cambridge University Press.
Haile, M. (2014). Integrated volarization of spent coffee grounds to biofuels. Biofuel Res. J., pp.65-69.
Han, J., Forman, G., Elgowainy, A., Cai, H., Wang, M. and DiVita, V. (2015). A comparative assessment of
resource efficiency in petroleum refining. Fuel, 157, pp.292-298.
Hennecke, A., Faist, M., Reinhardt, J., Junquera, V., Neeft, J. and Fehrenbach, H. (2013). Biofuel
greenhouse gas calculations under the European Renewable Energy Directive – A comparison of the
BioGrace tool vs. the tool of the Roundtable on Sustainable Biofuels. Applied Energy, 102, pp.55-62.
Hoe, J. and Hoare, Z. (2012). Understanding quantitative research: part 1. Nursing Standard, 27, p.53.
IMAHARA, H., MINAMI, E. and SAKA, S. (2006). Thermodynamic study on cloud point of biodiesel with
its fatty acid composition☆. Fuel, 85(12-13), pp.1666-1670.
IPIECA, (2013). Saving energy in the oil and gas industry. Climate Change 2013. London: IPIECA, pp.1-2.
Jenkins, R., Stageman, N., Fortune, C. and Chuck, C. (2014). Effect of the Type of Bean, Processing, and
Geographical Location on the Biodiesel Produced from Waste Coffee Grounds. Energy & Fuels, 28(2),
pp.1166-1174.
Johansson, T. and Burnham, L. (1993). Renewable energy. Washington, D.C.: Island Press.
Kondamudi, N., Mohapatra, S. and Misra, M. (2008). Spent Coffee Grounds as a Versatile Source of Green
Energy. J. Agric. Food Chem., 56(24), pp.11757-11760.
32
Kovarik, B. (1998). Henry Ford, Charles Kettering and the Fuel of the Future. Automotive History Review,
(32), pp.7-27.
Li, X., Strezov, V. and Kan, T. (2014). Energy recovery potential analysis of spent coffee grounds pyrolysis
products. Journal of Analytical and Applied Pyrolysis, 110, pp.79-87.
Ling, C. and Bridgeman, A. (2011). Quantitative Analysis in the General Chemistry Laboratory: Training
Students To Analyze Individual Results in the Context of Collective Data. J. Chem. Educ., 88(7), pp.979-
982.
Leung, D. and Guo, Y. (2006). Transesterification of neat and used frying oil: Optimization for biodiesel
production. Fuel Processing Technology, 87(10), pp.883-890.
Lewis, R. and Evans, W. (2006). Chemistry. Basingstoke [England]: Palgrave Macmillan.
Luque, R. (2010). Handbook of biofuels production. Oxford: Woodhead Publ.
Masum, B., Masjuki, H., Kalam, M., Palash, S. and Habibullah, M. (2015). Effect of alcohol–gasoline
blends optimization on fuel properties, performance and emissions of a SI engine. Journal of Cleaner
Production, 86, pp.230-237.
McKelvy, M., Britt, T., Davis, B., Gillie, J., Graves, F. and Lentz, L. (1998). Infrared Spectroscopy.
Analytical Chemistry, 70(12).
Mohr, A. and Raman, S. (2013). Lessons from first generation biofuels and implications for the
sustainability appraisal of second generation biofuels. Energy Policy, 63, pp.114-122.
Montross, M. (2010). Thermochemical conversion of biomass to liquid fuels and chemicals.
Cambridge[u.a.]: Royal Society of Chemistry.
Muniyappa, P., Brammer, S. and Noureddini, H. (1996). Improved conversion of plant oils and animal fats
into biodiesel and co-product. Bioresource Technology, 56(1), pp.19-24.
33
Murthy, P. and Madhava Naidu, M. (2012). Sustainable management of coffee industry by-products and
value addition—A review. Resources, Conservation and Recycling, 66, pp.45-58.
Noponen, M., Edwards-Jones, G., Haggar, J., Soto, G., Attarzadeh, N. and Healey, J. (2012). Greenhouse
gas emissions in coffee grown with differing input levels under conventional and organic
management. Agriculture, Ecosystems & Environment, 151, pp.6-15.
Odeh, O., Featherstone, A. and Bergtold, J. (2010). RELIABILITY OF STATISTICAL SOFTWARE.
American Journal of Agricultural Economics.
Otera, J. (1993). Transesterification. Chemical Reviews, 93(4), pp.1449-1470.
Practical Infra-Red Spectroscopy. (2002). [COSHH ASSESSMENT] University of Plymouth, Plymouth.
Rao, C. (1963). Chemical Applications of Infrared Spectroscopy. London: Academic Press Inc. (London)
LTD., pp.7-11.
Rathinavelu, R. and Graziosi, G. (2005). Potential alternative use of coffee wastes and by-products. pp.1-5.
Reitze, A. (n.d.). Electric Power in a Carbon Constrained World. SSRN Electronic Journal.
Rubayiza, A. and Meurens, M. (2005). Chemical Discrimination of Arabica and Robusta Coffees by Fourier
Transform Raman Spectroscopy. J. Agric. Food Chem., 53(12), pp.4654-4659.
Sawangkeaw, R., Bunyakiat, K. and Ngamprasertsith, S. (2010). A review of laboratory-scale research on
lipid conversion to biodiesel with supercritical methanol (2001–2009). The Journal of Supercritical Fluids,
55(1), pp.1-13.
Shipman, R., Conti, T., Tighe, T. and Buel, E. (2013). Forensic Drug Identification by Gas
Chromatography – Infrared Spectroscopy. The U.S. Department of Justice.
Shrestha, E., Ahmad, S., Johnson, W. and Batista, J. (2012). The carbon footprint of water management
policy options. Energy Policy, 42, pp.201-212.
34
Sidibé, S., Blin, J., Vaitilingom, G. and Azoumah, Y. (2010). Use of crude filtered vegetable oil as a fuel in
diesel engines state of the art: Literature review. Renewable and Sustainable Energy Reviews, 14(9),
pp.2748-2759.
Sims, R., Mabee, W., Saddler, J. and Taylor, M. (2010). An overview of second generation biofuel
technologies. Bioresource Technology, 101(6), pp.1570-1580.
Smedley, T. (2015). Arthur Kay: Guardian sustainable business leader of the year 2015. The Guardian.
Smith, R. (2000). Interpretation of organic data. Amsterdam, NY: Genium Pub. Corp.
Spear, B. (2008). Pharmacogenetics and Antiepileptic Drugs. Epilepsia, 42, pp.31-34.
Starbucks Coffee Company. (2016). Starbucks – The Best Coffee and Espresso Drinks. [online] Available
at: http://www.starbucks.com [Accessed 10 Apr. 2016].
Stuart, B. (2004). Infrared spectroscopy. Chichester, Eng.: J. Wiley.
Tan, Y., Abdullah, M. and Nolasco-Hipolito, C. (2015). The potential of waste cooking oil-based biodiesel
using heterogeneous catalyst derived from various calcined eggshells coupled with an emulsification
technique: A review on the emission reduction and engine performance. Renewable and Sustainable Energy
Reviews, 47, pp.589-603.
Vaccaro, I., Smith, E. and Aswani, S. (2010). Environmental social sciences. Cambridge: Cambridge
University Press.
Vardon, D., Moser, B., Zheng, W., Witkin, K., Evangelista, R., Strathmann, T., Rajagopalan, K. and
Sharma, B. (2013). Complete Utilization of Spent Coffee Grounds To Produce Biodiesel, Bio-Oil, and
Biochar. ACS Sustainable Chemistry & Engineering, 1(10), pp.1286-1294.
Veríssimo, M. and Gomes, M. (2011). Assessment on the use of biodiesel in cold weather: Pour point
determination using a piezoelectric quartz crystal. Fuel, 90(6), pp.2315-2320.
Voudouris, V. (2014). Oil and gas perspectives in the 21st century. Energy Policy, 64, pp.14-15.
35
Walz, K. and Kerr, S. (2007). "Holes" in Student Understanding: Addressing Prevalent Misconceptions
Regarding Atmospheric Environmental Chemistry. J. Chem. Educ., 84(10), p.1693.
White, L. and Plaskett, L. (1981). Biomass as fuel. London: Academic Press.
Zannikos, F., Anastopoulos, G. and Deligiannis, A. (2011). Waste Coffee Grounds as an Energy Feedstock.
Винокурова, Н. and Трушин, В. (1998). Глобальная Экология. Просвещение, pp.7-44.
Воронков, Н. (1999). Основы Общей Экологии. 4th ed. Moscow, pp.314-323.
Германович, В. and Турилин, А. (2014). Альтернативные источники энергии и энергосбережение.
Практические конструкции по использованию энергии ветра, солнца, воды, земли, биомассы. Наука
и Техника, pp.297-310.
Гринин, А. and Новиков, В. (2002). Промышленные и бытовые отходы Хранение, утилизация,
переработка. Фаир-Пресс.
Фелленберг, Г. (1997). Загрязнение природной среды. Moscow: Мир, pp.6-227.
36
Appendices
Appendix A. Biodiesel Sample Photographs And a Scanned Lab Book Page
Fig. A1
Figure A1 show the Starbucks (Drake Circus) biodiesel sample
37
Fig. A2
Figure A compares Starbucks (Drake Circus) and Costa (University Campus) biodiesel
38
Fig. A3
Figure A3 show Costa (Drake Circus), Nero (Cornwall Street) and Nero (Debenhams) biodiesel
39
Fig. A4
Figure A4 shows the amount of biodiesel (g) obtained from all 6 coffee houses. Figure was obtained from the scanned
copy of the lab book
40
Appendix B. Sample Infra-Red Graphs Before Transesterification
Fig. B1
Figure B1 shows Starbucks (Drake Circus) sample before and after transesterification on the infra-red spectroscopy
graph
41
Fig. B2
Figure B2 shows Costa (Drake Circus) sample before transesterification on the infra-red spectroscopy graph
42
Fig. B3
Figure B3 shows Nero (Debenhams) sample before transesterification on the infra-red spectroscopy graph
43
Fig. B4
Figure B4 shows Nero (Cornwall Street) sample before transesterification on the infra-red spectroscopy graph
44
Fig. B5
Figure B5 shows Costa (University Campus) sample before transesterification on the infra-red spectroscopy graph
45
Fig. B6
Figure B6 shows Starbucks (Armada Way) sample before transesterification on the infra-red spectroscopy graph
46
Appendix C. Excel Data Analysis
Table C1
Table C1 shows the amount of biodiesel (g) obtained from each coffee shop, as well as the found medium
Table C2
Table C2 shows the Pearson’s correlation value between the amount of the obtained biodiesel and the percentage of
Arabica beans in the spent coffee grounds
47
Appendix D. Energy Input Calculations
Fig. D1
Figure D1 shows the energy input calculations, using the formula obtained from (Breithaupt, J., 2010).
48
Fig. D2
Figure D2 shows the energy input calculations, using the formula obtained from (Breithaupt, J., 2010).
49
Appendix E. Scanned Laboratory Book
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
Appendix F. COSHH and Risk Assessment
66
67
68
69
70
71
72
73
74
75
76
77
top related