day4 2 initial configuration
Post on 05-Apr-2018
240 Views
Preview:
TRANSCRIPT
-
8/2/2019 Day4 2 Initial Configuration
1/34
INITIAL
CONFIGURATION
-
8/2/2019 Day4 2 Initial Configuration
2/34
Console Connectivity
RJ-45
Console PortConnector
RolloverCable
RJ-45 to DB-9Converter Computer
-
8/2/2019 Day4 2 Initial Configuration
3/34
Console Connectivity
Connect a rollover cable to the router console port(RJ-45 connector).Connect the other end of the rollover cable to theRJ-45 to DB-9 converterAttach the female DB-9 converter to a PC Serial Port.Open emulation software on the PC.
-
8/2/2019 Day4 2 Initial Configuration
4/34
Emulation Software
WINDOWSStart -> Programs -> Accessories -> Communications ->HyperTerminal ->HyperTerminal.Give the Connection Name & Select Any Icon
Select Serial (Com) Port where Router is Connected.In Port Settings -> Click on Restore DefaultsLINUX# minicom -s
-
8/2/2019 Day4 2 Initial Configuration
5/34
Console Connectivity
-
8/2/2019 Day4 2 Initial Configuration
6/34
6
-
8/2/2019 Day4 2 Initial Configuration
7/34
7
-
8/2/2019 Day4 2 Initial Configuration
8/34
8
-
8/2/2019 Day4 2 Initial Configuration
9/34
9
-
8/2/2019 Day4 2 Initial Configuration
10/34
10
-
8/2/2019 Day4 2 Initial Configuration
11/34
11
-
8/2/2019 Day4 2 Initial Configuration
12/34
12
-
8/2/2019 Day4 2 Initial Configuration
13/34
abc
13
-
8/2/2019 Day4 2 Initial Configuration
14/34
14
-
8/2/2019 Day4 2 Initial Configuration
15/34
15
-
8/2/2019 Day4 2 Initial Configuration
16/34
16
-
8/2/2019 Day4 2 Initial Configuration
17/34
17
-
8/2/2019 Day4 2 Initial Configuration
18/34
18
-
8/2/2019 Day4 2 Initial Configuration
19/34
System Bootstrap, Version 11.0(10c), SOFTWARE
Copyright (c) 1986-1996 by cisco Systems2500 processor with 2048 Kbytes of main memory
Notice: NVRAM invalid, possibly due to write erase.F3: 5575260+78596+410108 at 0x3000060
Restricted Rights Legend
Use, duplication, or disclosure by the Government issubject to restrictions as set forth in subparagraph(c) of the Commercial Computer Software - RestrictedRights clause at FAR sec. 52.227-19 and subparagraph(c) (1) (ii) of the Rights in Technical Data and ComputerSoftware clause at DFARS sec. 252.227-7013.
Cisco Systems, Inc.170 West Tasman DriveSan Jose, California 95134-1706
19
-
8/2/2019 Day4 2 Initial Configuration
20/34
Cisco Internetwork Operating System Software
IOS(tm) 2500 Software(C2500-P-L),Version 12.1(24),RELEASE SOFTWARE(fc1Copyright (c) 1986-2002 by cisco Systems, Inc.Compiled Mon 30-Sep-02 20:43 by sraniImage text-base: 0x0302EA54, data-base: 0x00001000
Cisco 2500(68030)processor(revision N) with 2048K/2048K bytes of memory
Processor board ID 11169613, with hardware revision 00000001
X.25 software, Version 3.0.0.Basic Rate ISDN software, Version 1.1.1 Ethernet/IEEE 802.3 interface(s)2 Serial network interface(s)1 ISDN Basic Rate interface(s)32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read ONLY)
--- System Configuration Dialog ---
Would you like to enter the initial configuration dialog? [yes/no]: n
20
-
8/2/2019 Day4 2 Initial Configuration
21/34
Press RETURN to get started!
00:00:20: %LINK-3-UPDOWN: Interface Ethernet0, changed state to up00:00:20: %LINK-3-UPDOWN: Interface Serial0, changed state to down00:00:20: %LINK-3-UPDOWN: Interface Serial1, changed state to down00:00:21: %LINEPROTO-5-UPDOWN: Line protocol on InterfaceEthernet0, changed state to up00:00:21: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0,changed state to down
00:00:21: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1,changed state to down00:12:43: %LINK-5-CHANGED: Interface Ethernet0, changed state toadministratively down00:12:43: %LINK-5-CHANGED: Interface Serial0, changed state toadministratively down00:12:43: %LINK-5-CHANGED: Interface Serial1, changed state to
administratively down00:12:44: %LINEPROTO-5-UPDOWN: Line protocol on InterfaceEthernet0, changed state to down00:12:46: %SYS-5-RESTART: System restarted
21
-
8/2/2019 Day4 2 Initial Configuration
22/34
Compiled Mon 30-Sep-02 20:43 User ModeRouter> enable
Router# show running-configtelnet, enableCommands :show, copy, write, reload, configure
terminal
Privileged :
Cisco Internetwork Operating System Software
IOS(tm) 2500 Software(C2500-P-L),Version 12.1(24),RELEASE SOFTWARE(fc1Copyright (c) 1986-2002 by cisco Systems, Inc.by srani
: CommandsMode
Building configuration .....Current configuration:
!version 12.1no service password-encryptionno service udp-small-serversno service tcp-small-servers!hostname Router
!
interface Ethernet0no ip addressshutdown--More--
22
-
8/2/2019 Day4 2 Initial Configuration
23/34
interface Serial0
no ip addressshutdown!interface Serial1no ip addressshutdown!no ip classless
!!line con 0line aux 0line vty 0 4login!
endRouter# show startup-config% Non-volatile configuration memory has not been set up or bad checksum
Router#
23
-
8/2/2019 Day4 2 Initial Configuration
24/34
Router# show flash
System flash directory:File Length Name/status1 8108960 /c2500-ipx-ip.bin
[8109024 bytes used, 8668192 available, 16777216 total]16384K bytes of processor board System flash (Read ONLY)
Router# show version
Cisco Internetwork Operating System SoftwareIOS (tm) 2500 Software (C2500-JS-L),Version 12.1(17),RELEASE SOFTWARECopyright (c) 1986-1999 by cisco Systems, Inc.Compiled Mon 04-Jan-99 17:27 by ashahImage text-base: 0x03040148, data-base: 0x00001000
ROM: System Bootstrap, Version 11.0(10c), SOFTWAREBOOTFLASH: 3000 Bootstrap Software (IGS-BOOT-R), Version 11.0(10c),RELEASE SOFTWARE (fc1)
--More--
24
-
8/2/2019 Day4 2 Initial Configuration
25/34
enable password, enable secret
Global memory.:System flash :
Router uptime is 1 hour, 28 minutes
System restarted by power-onSystem image file is "flash:/c2500-ipx-ip.bin", booted via flash
Cisco 2500(68030)processor(revision N) with 2048K/2048K bytes of memoProcessor board ID 11169613, with hardware revision 00000001X.25 software, Version 3.0.0.Basic Rate ISDN software, Version 1.1.1 Ethernet/IEEE 802.3 interface(s)2 Serial network interface(s)1 ISDN Basic Rate interface(s)
32K bytes of non-volatile configurationConfiguration Mode16384K bytes of processor board Commands (Read ONLY)
hostname, interface,Configuration register is 0x2102
Router# configure terminalEnter configuration commands, one per line. End with CNTL/Z.Router(config)# hostname HyderabadHyderabad(config)#
25
-
8/2/2019 Day4 2 Initial Configuration
26/34
Hyderabad(config-if)#ip address 192.168.1.150 255.255.255.0Hyderabad(config-if)# no shutdownHyderabad(config-if)# exit Configuring Ethernet interface
Hyderabad(config-line)# exit Setting Telnet password
Hyderabad(config-line)# login
Setting Console passwordHyderabad(config-line)# exit
line con 0Hyderabad(config)# line aux 0Router(config)#
Hyderabad(config-line)# password ciscoSetting Auxilary passwordHyderabad(config-line)# exitHyderabad(config)# enable password ciscoHyderabad(config)# enable secret zoom^ZHyderabad(config)#
4line vty
Router(config-if)#
line
Setting the Enable
Router(config)#login
Hyderabad(config)# interface ethernet 0
Interface Mode: Commands :ip address, no shutdown
Hyderabad(config)#Router(config)#0interface ethernet
Hyderabad(config-line)# login ip address Hyderabad(config-line)# password zoom
Router(config-if)# no shutdown
Hyderabad(config)#Router(config)#0line vty 0 4
Router(config-line)# loginHyderabad(config-line)# password ccna
Router(config-line)# password
Router(config)#enable password
Hyderabad(config-line)# enable secret Router(config-line)# login
Router(config-line)# password
Router(config)# line aux 0
Router(config-line)# login
Router(config-line)# password
26
-
8/2/2019 Day4 2 Initial Configuration
27/34
Hyderabad# show running-config
Building configuration .....Current configuration:!version 12.1no service password-encryptionno service udp-small-serversno service tcp-small-servers!
hostname Hyderabad!enable secret 5 $1$60nw$8XzAJ445GBzx1mgYJTUjo1enable password cisco!interface Ethernet0ip address 192.168.1.150 255.255.255.0
!interface Serial0no ip addressshutdown--More--
27
-
8/2/2019 Day4 2 Initial Configuration
28/34
interface Serial1
no ip addressshutdown!no ip classless!line con 0loginpassword ccna
line aux 0loginpassword ciscoline vty 0 4loginpassword zoom!
endHyderabad# show startup-config% Non-volatile configuration memory has not been set up or bad checksum
Hyderabad#
28
-
8/2/2019 Day4 2 Initial Configuration
29/34
Router#copy running-config startup-config
Saving Router
Hyderabad# copy running-config startup-config
Building configuration.....[OK]
Hyderabad# show startup-config ConfigurationBuilding configuration .....Current configuration:!version 12.1no service password-encryptionno service udp-small-serversno service tcp-small-servers!hostname Hyderabad!enable secret 5 $1$60nw$8XzAJ445GBzx1mgYJTUjo1
enable password cisco!interface Ethernet0ip address 192.168.1.150 255.255.255.0--More--
29
-
8/2/2019 Day4 2 Initial Configuration
30/34
interface Serial0no ip addressshutdown!interface Serial1no ip addressshutdown!no ip classless!line con 0loginpassword ccnaline aux 0loginpassword ciscoline vty 0 4loginpassword zoom!endHyderabad#
30
-
8/2/2019 Day4 2 Initial Configuration
31/34
Console Connectivity
Con 0
E0
LAN - 192.168.1.0/24
31
-
8/2/2019 Day4 2 Initial Configuration
32/34
================================
Welcome to Hyderabad Router================================
User Access Verification
password : ****
Hyderabad> enablepassword : ****Hyderabad#
32
-
8/2/2019 Day4 2 Initial Configuration
33/34
Microsoft Windows 2000 [Version 5.00.2195](C) Copyright 1985-2000 Microsoft Corp.C:\> telnet 192.168.1.150Connecting .....================================
Welcome to Hyderabad Router
================================
User Access Verification
password : ****
Hyderabad> enablepassword : ****Hyderabad#
33
-
8/2/2019 Day4 2 Initial Configuration
34/34
34
top related