cisco aironet family (5089) - ca...
Post on 29-Apr-2018
213 Views
Preview:
TRANSCRIPT
D e v i c e M a n a g e m e n t Page 2 C i s c o A i r o n e t F a m i l y
Copyright NoticeDocument 5089. Copyright © 2003-present by Aprisma Management Technologies, Inc. All rights reserved worldwide. Use, duplication, or disclosure by the United States government is subject to the restrictions set forth in DFARS 252.227-7013(c)(1)(ii) and FAR 52.227-19.Liability DisclaimerAprisma Management Technologies, Inc. (“Aprisma”) reserves the right to make changes in specifications and other information contained in this document without prior notice. In all cases, the reader should contact Aprisma to inquire if any changes have been made.
The hardware, firmware, or software described in this manual is subject to change without notice.
IN NO EVENT SHALL APRISMA, ITS EMPLOYEES, OFFICERS, DIRECTORS, AGENTS, OR AFFILIATES BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED IN IT, EVEN IF APRISMA HAS BEEN ADVISED OF, HAS KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES.
Trademark, Service Mark, and Logo InformationSPECTRUM, IMT, and the SPECTRUM IMT/VNM logo are registered trademarks of Aprisma Management Technologies, Inc., or its affiliates. APRISMA, APRISMA MANAGEMENT TECHNOLOGIES, the APRISMA MANAGEMENT TECHNOLOGIES logo, MANAGE WHAT MATTERS, DCM, VNM, SpectroGRAPH, SpectroSERVER, Inductive Modeling Technology, Device Communications Manager, SPECTRUM Security Manager, and Virtual Network Machine are unregistered trademarks of Aprisma Management Technologies, Inc., or its affiliates. For a complete list of Aprisma trademarks, service marks, and trade names, go tohttp://www.aprisma.com/manuals/trademark-list.htm.
All referenced trademarks, service marks, and trade names identified in this document, whether registered or unregistered, are the intellectual property of their respective owners. No rights are granted by Aprisma Management Technologies, Inc., to use such marks, whether by implication, estoppel, or otherwise. If you have comments or concerns
about trademark or copyright references, please send an e-mail to spectrum-docs@aprisma.com; we will do our best to help.
Restricted Rights Notice(Applicable to licenses to the United States government only.)This software and/or user documentation is/are provided with RESTRICTED AND LIMITED RIGHTS. Use, duplication, or disclosure by the government is subject to restrictions as set forth in FAR 52.227-14 (June 1987) Alternate III(g)(3) (June 1987), FAR 52.227-19 (June 1987), or DFARS 52.227-7013(c)(1)(ii) (June 1988), and/or in similar or successor clauses in the FAR or DFARS, or in the DOD or NASA FAR Supplement, as applicable. Contractor/manufacturer is Aprisma Management Technologies, Inc. In the event the government seeks to obtain the software pursuant to standard commercial practice, this software agreement, instead of the noted regulatory clauses, shall control the terms of the government's license.Virus DisclaimerAprisma makes no representations or warranties to the effect that the licensed software is virus-free.
Aprisma has tested its software with current virus-checking technologies. However, because no antivirus system is 100 percent effective, we strongly recommend that you write-protect the licensed software and verify (with an antivirus system in which you have confidence) that the licensed software, prior to installation, is virus-free.
Contact InformationAprisma Management Technologies, Inc.273 Corporate DrivePortsmouth, NH 03801Phone: 603-334-2100U.S. toll-free: 877-468-1448Web site: http://www.aprisma.com
D e v i c e M a n a g e m e n t Page 3 C i s c o A i r o n e t F a m i l y
ContentsINTRODUCTION 4
Purpose and Scope ........................................................4Required Reading ...........................................................4Supported Devices..........................................................5The SPECTRUM Model ..................................................5
TASKS 7
DEVICE VIEW 8
Interface Icons ................................................................9Interface Icon Subviews Menu......................................10Secondary Address Panel ............................................11
DEVICE TOPOLOGY VIEW 12
APPLICATION VIEWS 13
Main Application View...................................................13Supported Applications .................................................14
Common Applications................................................14Device-Specific MIBs.................................................15
Discovery Application....................................................16Discovery Cache Table View .................................16Interface Discovery Status Table ...........................17
PERFORMANCE VIEWS 18
CONFIGURATION VIEWS 19
Device Configuration View............................................ 19
MODEL INFORMATION VIEW 21
INDEX 22
D e v i c e M a n a g e m e n t Page 4 C i s c o A i r o n e t F a m i l y
Introduction
This section introduces the SPECTRUM Device Management documentation for the Cisco Aironet Wireless Access Point.
This introduction contains the following topics:
• Purpose and Scope
• Required Reading
• Supported Devices (Page 5)
• The SPECTRUM Model (Page 5)
Purpose and ScopeUse this document as a guide for managing the Cisco Aironet devices described on Page 5 with SPECTRUM management module SM-CIS1016. This document describes the icons, menus, and views that enable you to remotely monitor, configure, and troubleshoot Cisco Aironet devices through software models in your SPECTRUM database.
Information specific to SM-CIS1016 is what is primarily included in this document. For general information about device management using SPECTRUM and explanations of SPECTRUM
functionality and navigation techniques, refer to the topics listed under Required Reading.
Required ReadingTo use this documentation effectively, you must be familiar with the information covered by the other SPECTRUM online documents listed below.
• Getting Started with SPECTRUM for Operators
• Getting Started with SPECTRUM for Administrators
• How to Manage Your Network with SPECTRUM
• SPECTRUM Views
• SPECTRUM Menus
• SPECTRUM Icons
• SPECTRUM Software Release Notice
• Cisco Applications
I n t r o d u c t i o n S u p p o r t e d D e v i c e s
D e v i c e M a n a g e m e n t Page 5 C i s c o A i r o n e t F a m i l y
Supported DevicesSPECTRUM management module SM-CIS1016 currently lets you model the following devices:
• Cisco Aironet 340 Series Access Point• Cisco Aironet 350 Series Access Point • Cisco Aironet 1200 Series Access Point
- 1200- 1220- 1210/1230 (IOS-based firmware)
• Cisco Aironet 1100 Series Access Point (IOS-based firmware)
• Cisco Aironet 1400 Series Access Point (IOS-based firmware)
Cisco Aironet products can be integrated into wired Ethernet networks, and they provide protection through full compliance with the IEEE 802.11b wireless standard.
The Cisco Aironet 1200 supports 2.4 GHz and 5 GHz radios simultaneously, preserving existing IEEE 802.11b investments and providing a migration path to future IEEE 802.11a and IEEE 802.11g technologies.
The SPECTRUM ModelThe model types for the Cisco Aironet devices are Aironet and AironetIOS. The AironetIOS model type is used for those devices that have IOS-based firmware. Devices with non-IOS-based firmware use the Aironet model type.
Modeling results in the creation of Device icons that represent the devices and Application icons that represent their supported applications.
The Device icons contain double-click zones and provide access to Icon Subviews menus that let you perform device management activities such as those listed in Tasks on Page 7.
As Figure 1 shows, the appearance of the Device icons varies slightly depending on the kind of view it appears in.
I n t r o d u c t i o n T h e S P E C T R U M M o d e l
D e v i c e M a n a g e m e n t Page 6 C i s c o A i r o n e t F a m i l y
Figure 1: Device Icons
The device-specific Icon Subviews menu options available from the Device icon are listed below.
The rest of this document covering management module SM-CIS1016 is organized as follows:
• Tasks (Page 7)
• Device View (Page 8)
• Device Topology View (Page 12)
• Application Views (Page 13)
• Performance Views (Page 18)
• Configuration Views (Page 19)
• Model Information View (Page 21).
Option Accesses the...
Fault Management
Fault Management view, which is described in the How to Manage Your Network with SPECTRUM documentation.
Device Device View (Page 8)
DevTop Device Topology View (Page 12)
Model Name
Cisco 1200 AP
Model Name
Cisco 1200 AP
Small Device icon appears inTopology and Application views
Large Device icon appears inDevice Topology, Location, andDevice Interface views.
Application Application Views (Page 13)
Configuration Configuration Views (Page 19)
Model Information
Model Information View (Page 21)
Primary Application
Menu options that let you select the primary application; for example, Gen Bridge App, MIB-II, etc.
Entity Tables This view is available when the device supports RFC2737. It displays the RFC2737App’s Physical and Logical Entity tables.
Option Accesses the...
D e v i c e M a n a g e m e n t Page 7 C i s c o A i r o n e t F a m i l y
Tasks
This section contains an alphabetical list of device management tasks, with each task providing one or more links to views that let you perform the task.
Administrative Information (check)• Model Information View (Page 21)
Alarm Thresholds (set)• Interface Icon Subviews Menu (Page 10)
Configuration Information (check)• Configuration Views (Page 19)
IP Address (find/change)• Device View (Page 8)• Secondary Address Panel (Page 11)
Network Type (check)• Network Type Label (Page 10)
Performance (check)• Device View (Page 8)• Interface Icons (Page 9)• Performance Views (Page 18)
Topology (check)• Device Topology View (Page 12)
D e v i c e M a n a g e m e n t Page 8 C i s c o A i r o n e t F a m i l y
Device View
This section describes the Device view and subviews available for models of Cisco Aironet devices in SPECTRUM.
Access: From the Icon Subviews menu for the Device icon, select Device.
This view (Figure 2) uses icons and labels to represent the device and its components, such as modules, ports, and applications. The view provides dynamic configuration and performance information for each of the device’s serial and network I/O ports, which are represented by Interface icons in the bottom panel of the view. The middle panel of the view displays a Device icon, which lets you monitor the device operation and access other device-specific views.
Figure 2: Device View
SpectroGRAPH: Router Device: Model Name
File View HelpTools
Model NameContactDescriptionLocation
Sys Up TimeManufacturerDevice TypeSerial Number
Network Address
Interface Description
Filter Physical
Interface Options PanelDevice Icon
Aironet
Model Name
1Ethernet
0:0:1D:F:FD:B6
ei0
0.0.0.0
ON
5SFTWARLPBK
0:0:1D:F:FD:B6
lo0
0.0.0.0
ON
9ATM8023
0:0:1D:F:FD:B6
zn1
0.0.0.0
ON
512AAL5
UAAL5
0.0.0.0
ON
2ATMCPU
0.0.0.0
ON
6ATM portCPU.1
0.0.0.0
ON
ATM7A1
0.0.0.0
ON
ATM7B1
0.0.0.0
ON
ATM7B2
0.0.0.0
ON
ATM7B3
0.0.0.0
ON
ATM8B1
0.0.0.0
ON
ATM8B2
0.0.0.0
ON
ATM8B3
0.0.0.0
ON
ATM8B4
0.0.0.0
ON
10
2783905 2783909
11
7
3 4
8
Interface Icons
Bookmarks
Model Name of type Model Type of Landscape node: Primary
Primary Application Gen Bridge App
D e v i c e V i e w I n t e r f a c e I c o n s
D e v i c e M a n a g e m e n t Page 9 C i s c o A i r o n e t F a m i l y
Interface IconsFigure 3 shows a close-up of an Interface icon from the Device view. Most of the informational labels on the icon also provide double-click access to other views, as explained in the following label descriptions.
Figure 3: Interface Icon
Interface Number LabelThis label displays the interface (port) number.
IF Status LabelThis label displays the current status of the interface for the primary application selected, e.g., Gen Rtr App or MIB-II App. Table 1 lists the possible label color representations. Note that the color of the label also depends on the interface’s current Administrative Status, which you set in the Interface Configuration View. This view can be accessed by double-clicking the Interface Type label.
Interface Type LabelThis label identifies the interface type (Ethernet, ATM, etc.). Double-click this label to access the Interface Configuration view. See the SPECTRUM Views documentation.
c
f
b
1ethernet
0:0:1D:F:FD:B6
a
a Interface Number Label
b IF Status Label
c Interface Type Label
d Network Type Label
e Physical Address Label
f IP Address Label
fxp0
0.0.0.0
d
e
ONTable 1: Interface Status Label Colors
ColorOperational
StatusAdministrative
StatusLabelText
Green up up ON
Blue down down OFF
Yellow down up OFF
Red testing testing TEST
D e v i c e V i e w I n t e r f a c e I c o n S u b v i e w s M e n u
D e v i c e M a n a g e m e n t Page 10 C i s c o A i r o n e t F a m i l y
Network Type LabelThis label identifies the type of network to which the interface is connected. Double-click the label to open the Model Information view for the interface.
Physical Address LabelThis label displays the physical (MAC) address of the interface. Double-click this label to open the Address Translation Table (AT).
IP Address LabelThis label displays the IP address for the interface. Double-click this label to open the Secondary Address Panel (Page 11), which lets you change the address and mask for the interface.
Interface Icon Subviews MenuTable 2 lists the device-specific interface Icon Subviews menu options and the views to which they provide access.
Table 2: Interface Icon Subviews Menu
Option Accesses the...
Detail Interface Detail view, which displays packet, error, and discard breakdown statistics for the interface.
IF Configuration Interface Configuration view (see SPECTRUM Views).
Address Translation Table
Address Translation Table (AT) (see SPECTRUM Views).
Secondary Address Panel
Secondary Address Panel (Page 11).
Thresholds Interface Threshold view, which lets you set the on/off alarm thresholds for load, packet rate, error rate, and % discarded for the interface.
Model Information
Model Information View (Page 21).
Trap Configuration
Interface Trap Configuration view (see How to Manage Your Network with SPECTRUM).
D e v i c e V i e w S e c o n d a r y A d d r e s s P a n e l
D e v i c e M a n a g e m e n t Page 11 C i s c o A i r o n e t F a m i l y
Secondary Address PanelAccess: From the Icon Subviews menu for the Interface icon in the Device view, select Secondary Address Panel.
This panel provides a table of IP addresses and masks obtained from the Address Translation table within the device’s firmware. You can change the current address displayed in the IP Address field by selecting an entry from the table in this panel and clicking the Update button.
D e v i c e M a n a g e m e n t Page 12 C i s c o A i r o n e t F a m i l y
Device Topology View
This section describes the Device Topology view available for models of the Cisco Aironet devices.
Access: From the Icon Subviews menu for the Device icon, select DevTop.
The Device Topology view (Figure 4) shows the connections between a modeled device and other network entities. The lower panel of the view uses Interface icons to represent the device’s serial, network, and I/O ports. These icons provide the same information and menu options as those in the Device View (Page 8). If a device is connected to a particular interface, a Device icon appears on the vertical bar above the Interface icon along with an icon representing the network group that contains the device.
Refer to the SPECTRUM Views documentation for details on Device Topology view.
Figure 4: Device Topology View
File View HelpTools
1Ethernet
0:0:1D:F:FD:B6ei0
0.0.0.0
ON 2ATM
0:0:1D:F:FD:B6A2
0.0.0.0
ON 3ATM
0:0:1D:F:FD:B6CPU
0.0.0.0
ON
Aironet
Model Name
Bookmarks
SpectroGRAPH: Device Topology: Model Name
Graphic ofCisco Aironet
Device
Model Name of type Model Type of Landscape node: Primary
D e v i c e M a n a g e m e n t Page 13 C i s c o A i r o n e t F a m i l y
Application Views
This section describes the main Application view and the associated application-specific subviews available for models of Cisco Aironet devices in SPECTRUM.
Access: From the Icon Subviews menu for the Device icon, select Application.
Main Application ViewWhen a device model is created, SPECTRUM automatically creates models for each of the major and minor applications supported by the device. The main Application view identifies all of these application models, shows their current condition status, and provides access to application-specific subviews. Figure 5 shows this view in the Icon mode. If you prefer the List mode, which displays applications as text labels, select View > Mode > List.
For more information on this view, refer to the MIBs and the Application View document.
Figure 5: Main Application View
SpectroGRAPH: Application: Model Name
Model Name
Contact
Description
Location
Network Address System Up Time
Manufacturer
Device Type
Serial Number
Model Name
6E132_25
Model Name
Aironet
File View Tools Bookmarks
Model Name of type <model type> of Landscape node: Primary
Help
A p p l i c a t i o n V i e w s S u p p o r t e d A p p l i c a t i o n s
D e v i c e M a n a g e m e n t Page 14 C i s c o A i r o n e t F a m i l y
Supported ApplicationsSPECTRUM’s applications can be grouped within two general categories as follows:
• Applications associated with non proprietary MIBs. See Common Applications below.
• Applications associated with device-specific MIBs. See Device-Specific MIBs (Page 15).
Common ApplicationsFor the most part, these applications represent the non proprietary MIBs supported by devices. Listed below (beneath the title of the SPECTRUM document that describes them) are some of the common applications currently supported by SPECTRUM. Refer to these documents when your devices support these applications.
• Routing Applications- Generic Routing- Repeater- AppleTalk- DECnet
- OSPF- OSPF2- BGP4- VRRP- RFC 2932
• Bridging Applications- Ethernet Special Database- Spanning Tree- Static- Transparent- PPP Bridging- Source Routing- Translation- QBridge
• MIB II Applications- SNMP- IP- ICMP- TCP- System2- UDP
• Transmission Applications- FDDI- Point to Point- DS1- DS3
Note:Note:
The documents listed below (in bold font) are available for viewing at:
www.aprisma.com/manuals/
A p p l i c a t i o n V i e w s S u p p o r t e d A p p l i c a t i o n s
D e v i c e M a n a g e m e n t Page 15 C i s c o A i r o n e t F a m i l y
- RS-232- WAN- Frame Relay- Token Ring- Ethernet- Fast Ethernet- RFC 1317App- RFC 1285App- RFC 1315App- 802.11App- SONET
• Technology Applications- APPN- ATM Client- DHCP- DLSw- PNNI- RFC 1316App- RFC 1514- RFC 2287- RFC 2790- RFC 2925
• DOCSIS Applications- DOCSISCblDvApp - DOCSISQOSApp- DOCSISBPI2App - DOCSISBPIApp
- DOCSISIFApp
• Digital Subscriber Line (DSL) Applications- ADSL
Device-Specific MIBsSPECTRUM imports the following device-level proprietary MIBs into its database:
• AWCVX-MIB.my• ACW-VLAN-CFG-MIB.my• CISCO-CDP-MIB.my
These MIBs can be used in conjunction with SPECTRUM’s optional customization products (referred to as the Level I Tool Kits) to create application models and views that display the condition of selected MIB objects.
The following device-specific application is described in the remainder of this section:
• Discovery Application (Page 16)
Note:Note:
Aprisma Management Technologies can provide training, technical assistance, and custom engineering support services for creating application models and their associated views.
A p p l i c a t i o n V i e w s D i s c o v e r y A p p l i c a t i o n
D e v i c e M a n a g e m e n t Page 16 C i s c o A i r o n e t F a m i l y
Discovery ApplicationThis application (CiscoCDPApp) has three menu options that provide access to the following views.
• Discovery Cache Table View (Page 16) • Interface Discovery Status Table (Page 17)• Model Information View (Page 21)
Discovery Cache Table ViewAccess: From the Icon Subviews menu for the CiscoCDPApp Application icon, select Cache.
This table contains the cached information obtained by receiving Cisco Discovery Protocol (CDP) messages.
Type An indication of the type of address contained in the corresponding instance of cdpCacheAddress.
AddressThe (first) network-layer address of the device’s SNMP-agent as reported in the most recent CDP message.
Device IDThe Device-ID string as reported in the most recent CDP message. The zero-length string indicates no Device-ID field was reported in the most recent CDP message.
Device PortThe Port-ID string as reported in the most recent CDP message. This will typically be the value of the ifName object (e.g., ‘Ethernet0’.) The zero-length string indicates no Port-ID field was reported in the most recent CDP message.
PlatformThe device’s hardware platform as reported in the most recent CDP message. The zero-length string indicates that no Platform field was reported in the most recent CDP message.
CapabilitiesThe device’s functional capabilities as reported in the most recent CDP message. For the latest set of specific values, see the latest version of the CDP specification. The zero-length string indicates no Capabilities field was reported in the most recent CDP message.
A p p l i c a t i o n V i e w s D i s c o v e r y A p p l i c a t i o n
D e v i c e M a n a g e m e n t Page 17 C i s c o A i r o n e t F a m i l y
Interface Discovery Status TableAccess: From the Icon Subviews menu for the CiscoCDPApp Application icon, select Interfaces.
This table contains the status of Cisco Discovery Protocol (CDP) on the device’s interfaces.
IFThe interface index value of the local interface.
DiscoveryAn indication of whether the Cisco Discovery Protocol is currently running on this interface.
GroupThis object is only relevant to interfaces that are repeater ports on 802.3 repeaters; it indicates the RFC1516 group number of the repeater port that corresponds to this interface.
PortThis object is only relevant to interfaces that are repeater ports on 802.3 repeaters; it indicates the RFC1516 port number of the repeater port that corresponds to this interface.
IntervalThe interval at which CDP (Cisco Discovery Protocol) messages are to be generated on this interface. The default value is 60 seconds.
D e v i c e M a n a g e m e n t Page 18 C i s c o A i r o n e t F a m i l y
Performance Views
This section introduces the Performance view. For details concerning this view, refer to the SPECTRUM Views documentation.
Performance views display performance statistics in terms of a set of transmission attributes, e.g., cell rates, frame rates, % error, etc. A typical view is shown in Figure 6. The instantaneous condition of each transmission attribute is recorded in a graph. The statistical information for each attribute is presented in the adjacent table.
Generally, you determine performance at the device level through Performance views accessed from the Device and Application icons. You determine performance at the port/interface level through Performance views accessed from Interface icons.
Figure 6: Performance View
SpectroGRAPH: Type Routing
File View Tools Bookmarks
% Discarded
type routing of type IP Routing of Landscape node: Primary
Performance View
Day/Month/ Time/ Year
100.0
10.01.000.100.010
00:30 00:20 00:10 0
* Received/sec
% Discarded
% Forwarded
% Trans/sec
Value Average Peak Value
Scroll to Date-TimeGraph Properties* Graph X 1000
Log
Network Address Device Type
Detail
at
at
at
at
D e v i c e M a n a g e m e n t Page 19 C i s c o A i r o n e t F a m i l y
Configuration Views
This section describes the Configuration views available for models of the Cisco Aironet devices in SPECTRUM.
Configuration views let you see and modify current settings for the modeled device and its interfaces, ports, and applications. The following Configuration views are available for models of Cisco Aironet devices:
• Device Configuration View (Page 19)
Device Configuration ViewAccess: From the Icon Subviews menu for the Device icon, select Configuration.
A typical Device Configuration view is shown in Figure 7. Generally, this view includes a few fields that display device information as well as an Interface Configuration Table that lists interface parameters, some of which can be changed (see SPECTRUM Views). Some Device Configuration views include one or more buttons that provide access to device-specific configuration information. These are described below.
Figure 7: Device Configuration View
SpectroGRAPH: Model Name
Model Name
File View Tools Bookmarks Help
DescriptionLocation
ContactManufacturerSys Up Time
Net Address
Device Type
Serial Number
Configuration View
Contact Status Number of Interfaces
Interface Address Translation
Sort Interface Configuration Table
Index Description Type Bandwidth Physical Addre
IP Address of type Model of Landsape: Primary
Find Update
Redundancy and Model Reconfiguration Options
C o n f i g u r a t i o n V i e w s D e v i c e C o n f i g u r a t i o n V i e w
D e v i c e M a n a g e m e n t Page 20 C i s c o A i r o n e t F a m i l y
Refer to the SPECTRUM Views documentation
Refer to the SPECTRUM Views documentation.
Redundancy and Model Reconfiguration Options
Interface Address Translation
D e v i c e M a n a g e m e n t Page 21 C i s c o A i r o n e t F a m i l y
Model Information View
This section provides a brief overview of the Model Information view.
Model Information views display administrative information about devices and their applications and let you set thresholds and alarm severity for the devices.
Figure 8 shows a sample Model Information view. The layout of this view is the same for all model types in SPECTRUM but some information will vary depending on the model it defines. Refer to the SPECTRUM Views documentation for a complete description of this view.
Figure 8: Model Information View
Model Name ContactDescriptionLocation
SpectroGRAPH: Model Name
File View Tools Bookmarks Help
IP Address of Model Type of Landscape: Primary
ManufacturerSysUpTime
Net AddressDevice TypeSerial Number
Model Information View
MM Name
MM Part Number
MM Version Number
Model Type
Model Creation Time
Model Created By
Model State
Security String
Communication Information
Poll / Log Information
Condition Value
Contact Status
DCM TimeOut
DCM Retry
Lost Child Count
Value When Yellow
Value When OrangeValue When Red
Community Name
Mgnmt Protocol
Poll Interval
Poll Status
Log Ratio
Last Successful Poll
Logged Polled
True
General InformationCondition
S P E C T R U M E n t e r p r i s e M a n a g e r Page 22 C i s c o A i r o n e t F a m i l y
Index
AACW-VLAN-CFG-MIB.my 15Address
Interface IP 10Physical (MAC) 10Translation 11
Admin Status 9Aironet 5AironetIOS 5Applications 13AWCVX-MIB.my 15
CCiscoCDPApp 16CISCO-CDP-MIB.my 15Common Applications 14Configuration
Device 19
DDevice Specific MIBs 15DevTop Views 12Discovery Application
Cache Table View 16Interface Discovery Status
Table 17Documentation 4
EEntity Tables 6
HHardware 5
IIcon
Subview documentation 6Subviews 6
IconsDevice 6Interface 9
IF Configuration 10Interface
Type, Device 9IOS-based firmware 5
LLine Statuses 18
MManagement Tasks 7Mask 11MIB Support
ACW-VLAN-CFG-MIB.my 15AWCVX-MIB.my 15
ModelCisco 1100 series 5Cisco 1200 Series 5Cisco 1400 Series 5Cisco 340 series 5Cisco 350 Series 5Information 21Types of 5
NNetwork I/O ports 12Network Type 10
I n d e x I n d e x
S P E C T R U M E n t e r p r i s e M a n a g e r Page 23 C i s c o A i r o n e t F a m i l y
PPerformance Statistics 18Port Number, Device 9
RRFC2737App 6
SSerial ports 12Supported Applications 14
TThreshold Information 10Troubleshooting 7
VViewing other documents 14
list 14online 14
top related