32wp95e
Post on 16-Jul-2015
15 Views
Preview:
TRANSCRIPT
5/14/2018 32WP95E - slidepdf.com
http://slidepdf.com/reader/full/32wp95e 1/17
SERVICE MANUALDOCUMENTATION TECHNIQUETECHNISCHE DOKUMENTATIONDOCUMENTAZIONE TECNICADOCUMENTACION TECNICA
No copying, translati on, modifi cation on other use authorized. All rights reserved worldwide. • Tous droits de reproduction, de traductio n, d'adaptation et d'exécution réservés pour tous les pays. • Sämtliche Urheberrechte an diesen Texten und Zeichnungen stehen uns zu. Nachdrucke,Vervielfältigungen - auch auszugsweise - nur mit unserer vorherigen Zustimmung zulässig. Alle Rechte vorbehalten. • I diri tti di riproduzione, di traduzione, e esecuzione sono riservati per tutti i paesi. • Derechos de reproduccion, de traduccion, de adaptacion y de ejecucion reservados para todos los pai ses.
WARNING : Before servicing this chassis please read the safety recommendations.
ATTENTION : Avant toute intervention sur ce châssis, lire les recommandations de sécurité.
ACHTUNG : Vor jedem Eingriff auf diesem Chassis, die Sicherheitsvorschriften lesen.
ATTENZIONE : Prima di intervenire sullo chassis, leggere le norme di sicurezza.
IMPORTANTE :Antes de cualquier intervención, leer las recomendaciones de seguridad.
32WP95E - 0402
32WP95E
T V
Plasma
5/14/2018 32WP95E - slidepdf.com
http://slidepdf.com/reader/full/32wp95e 2/17
MAIN
FRANÇAIS ESPAÑOLDEUTSCHENGLISH ITALIANO
123456789
101112131415161718192021
NC
NC
21
17
19
15
13
20
18
16
14
1211
910
87
5
3
1
6
4
2
NC
AUDIO "R"
AUDIO "R"
AUDIO "L"
NOTE : ... etc. identifies each
pcb module.
AUDIO "D"
AUDIO "D"
AUDIO "G"
AUDIO
"BLEU"
AUDIO "G" MONO
"BLEU"
COMMUT. LENTE
"VERT"
"VERT"
"ROUGE"
COMMUT. RAPIDE
COMMUT. RAPIDE
VIDEO
VIDEO SYNCHRO
BLINDAGE PRISE
AUDIO "R"
AUDIO "R"
AUDIO "L"
AUDIO
"BLAU"
AUDIO "L" MONO
"BLAU"
AVUMSCHALTUNG
"GRÜN"
"GRÜN"
"ROT"
AUSTASTUNG
AUSTASTUNG
VIDEO
VIDEO ODERSYNCHRO
ABSCHIRMUNGDES STECKERS
AUDIO "D"
AUDIO "D"
AUDIO "I"
AUDIO
"AZUL"
AUDIO "I" MONO
AZUL
"CONMUTACIONLENTA"
"VERDE"
"VERDE"
"ROJA"
"CONMUTACIONRAPIDA"
"CONMUTACIONRAPIDA"
VIDEO
VIDEO O SINCRO
BLINDAJEDEL ENCHUFE
AUDIO "D"
AUDIO "D"
AUDIO "S"
AUDIO
"BLU"
AUDIO "S" MONO
BLU
"COMMUTAZIONELENTA"
"VERDE"
"VERDE"
"ROSSO"
"COMMUTAZIONERAPIDA"
"COMMUTAZIONERAPIDA"
VIDEO
VIDEO O SINCRO
INVOLUCRO METAL-LICO DELLA PRESA
AUDIO "L" MONO
"BLUE"
"GREEN"
"GREEN"
"RED"
"ROUGE" "ROT" "ROJA""ROSSO""RED"
SLOW SWITCH
FAST SWITCH
VIDEO
VIDEO VIDEO VIDEOVIDEOVIDEO
PLUG SCREENBOX
VIDEO OR "SYNC"
FAST SWITCH
AUDIO
"BLUE"
: OUTPUT - SORTIE - AUSGANG - USCITA - SALIDA • : EARTH - MASSE - MASSE - MASSA - MASA
MAINNOTE : ... etc. repères des
platines constituant l'appareil.
MAINNOTA : ... etc. marcas de las
placas que constituyen el aparato.
MAINNOTA : ... ecc. sigla delle
piastre dell' apparecchio.
MAINHINWEIS : ... usw. Kennzeichnung
der Platinen, aus denen das
Gerät zusammengesetzt ist.
: INPUT - ENTRÉE - EINGANG - ENTRATA - ENTRADA •
Indicates critical safety components, and identical components should be used for replacement. Only then can theoperational safety be garanteed.
Le remplacement des éléments de sécurité (repérés avec le symbole ) par des composants non homologués selon laNorme CEI 65 entraine la non-conformité de l'appareil. Dans ce cas, la responsabilité du fabricant n'est plus engagée.
Wenn Sicherheitsteile (mit dem Symbol gekennzeichnet) nicht durch Original - Ersatzteile ersetzt werden, erlischt dieHaftung des Herstellers.
La sostituzione dei componenti di sicurezza (evidenziati con il segno ) con componenti non omologati secondo lanorma CEI 65 comporta la non conformitá dell'apparecchio. In tal caso è "esclusa la responsabilità " del costruttore.
La sustitución de elementos de seguridad (marcados con el simbolo ) por componentes no homologados segun lanorma CEI 65, provoca la no conformidad del aparato. En ese caso, el fabricante cesa de ser responsable.
MEASUREMENT CONDITIONS - CONDITIONS DE MESURES - MESSBEDINGUNGENCONDIZIONI DI MISURA - CONDICIONES DE MEDIDAS
RICEVITORE :In UHF, livello d'entrata 1 mV, monoscopio barre :- PAL, norma G. bianco 100%.
Via SCART, livello d'entrata 1 Vpp, monoscopio barre :Colore, Contrasto, Luminositá media, Suono minimo.Programma selezionato PR 01.
Tensioni continue rilevate rispetto alla massa con un voltmetro digitale.
RECEIVER :On UHF,input level : 1 mV, bar test pattern :- PAL, I standard, 100% white.
Via the scart socket, input level : 1 Vpp, bar test pattern :
Colour, contrast and brightness at mid-position, sound at minimum.Programme selected : PR 01.
DC voltages measured between the point and earth using a digitalvoltmeter.
EMPFÄNGER :Bei UHF Eingangspegel 1 mV, Farbbalken :- PAL, Norm G, Weiss 100%.
Über die Scartbuchse : Eingangspegel 1 Vss, Farbbalken :
Farbe, Kontrast, Helligkeit in der Mitte des Bereichs, Ton auf Minimum.Zugeordnetes Programm PR 01.
Gleichspannungen mit einem digitalen Voltmeter zur Masse gemessen.
RECEPTEUR :En UHF, niveau d'entrée 1 mV mire de barres- SECAM, Norm L, Blanc 100%.
Par la prise Péritélévision, niveau d'entrée 1 Vcc, mire de barres .
Couleur, contraste, lumière à mi-course, son minimum.Programme affecté PR 01.
Tensions continues relevées par rapport à la masse avec unvoltmètre numérique.
RECEPTOR :En UHF, nivel de entrada 1 mV, mira de barras :- PAL, norma G, blanco 100%.
Por la toma Peritelevision, nivel de entrada 1 Vpp mira de barra.Color, Contraste, luz a mitad de carrera, Sonido minimo.Programa afectado PR 01.
Tensiones continuas marcadas en relacion a la masa con un voltimetro digital.
Do not disconnect modules when they are energized!Repairs on power supply section are to be carried out only with isolating transformer.
Ne pas retirer les modules lorsqu' ils sont sous tension. N'effectuer les travaux de maintenance sur la partie reliéeau secteur (Switch Mode) qu'au travers d'un transformateur d'isolement.
Module nicht bei eingeschaltetem Gerät entfernen!Servicearbeiten am Netzteil nur unter Verwendung eines Regeltrenntrafos durchführen.
Non scollegare le piastre quando sono alimentate!Per le riparazioni sulla sezione alimentatore, utilizzare un trasformatore isolatore.
No desconectar los módulos cuando están activados. Las reparaciones en la sección de alimentación de energíadeben ser ejecutadas solamente con un transformador de separación.
5/14/2018 32WP95E - slidepdf.com
http://slidepdf.com/reader/full/32wp95e 3/17
First issue 04 / 02 3
Page
DISASSEMBLING THE MODULES
Removing the optional speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Removing the back panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Removing the front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Removing the fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Removing the chassis assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Removing the PDP module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Removing the optical Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Removing the power module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Removing the flat cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
BOARD LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
DIAGNOSTIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
BLOCK DIAGRAMS
Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
ADJUSTMENTS
Mode service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Fixed data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
White balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
PDP power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Adjustment table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
CONTENTS
5/14/2018 32WP95E - slidepdf.com
http://slidepdf.com/reader/full/32wp95e 4/17
DISASSEMBLING THE MODULES
4 First issue 04 /02
1. Removing the optional speaker
- Put the PDP Monitor Display with the screen face down on
the flat desk.
CAUTION : When placing the display with the face down,
lay the soft cloth under the screen to protect the screen
surface. And make sure there is nothing to damage the
screen surface like a screw or small part near by before
placing the display.
- Remove speaker lead wires (R & L).
- Remove 16 Screws and 4 plates . (Fig. 1)
2. Removing the back panel
- Remove the 14 screws (4X8), the 10 screws (5X8)and the 2 screws (3X8).
- Remove the back panel.
050403
0201
01
02
02
01
01
01
03 03 03 03
03
03
03
03030303
03
03
03 04 04
0404
0404
04
0404
04 05 05
5/14/2018 32WP95E - slidepdf.com
http://slidepdf.com/reader/full/32wp95e 5/17
First issue 04 / 02 5
3. Removing the front panel
- Remove the 16 screws (4X8),
- Remove the flat cable from button unit to audio unit.
- Lift the chassis assembly up from the front panel and place
it the face down to the desk on soft cloth.
ATTENTION:
This PDP monitor is used the different kind of screw. Using
correct screw is needed to avoid the damage.
ATTENTION:
As R/C Pre-amp is projected from surface of the panel, it is
necessary to place it out of desk as shown below.
07
06
06
06 06 06 06 06 06 06 06
06 06 06 06 06 06
07
06
R/C Pre-amp
Front panel
Desk
5/14/2018 32WP95E - slidepdf.com
http://slidepdf.com/reader/full/32wp95e 6/17
4. Removing the chassis assembly
- Remove the 2 screws (4X8 + 2 washers) and the 2
screws (3X6)
- Remove fans with holder plate.
- Remove the 14 screws (6X12) and the 4 screws (5X8),
- Remove the 2 hexagonal screws,- Slightly lift the chassis up,
- Disconnect the lead wire between main unit and panel
module from panel module side,
- Remove the fixing screw of the 2 yellow-green wires
(ground) from AC power connector and Panel Module,
- Remove the 4 screws (5X40)
- Remove the panel holders and the spacers located
between holder and module.
- Disconnect the lead wire between Audio Unit and panel
module from panel module side,
- Disconnect the 3 connectors (KPOW2, K6U and
KPOW3) from power unit,
- Disconnect the connector (KSENS1) of sensor unit,
- Lift the chassis assembly up from panel module.
20
19
18
12
11
17
16
15
1413
10
09
08
09
11
11
11
121211
08 10 10 08
1314 1419
1816
17
15
14 14 1313
15
20
13
13
13
6 First issue 04 /02
5/14/2018 32WP95E - slidepdf.com
http://slidepdf.com/reader/full/32wp95e 7/17
5. Removing the PDP module
- Remove the 2 screws ( 3X8) and the 3 screws
- Remove the power unit and the sensor uni t with
holder plate from PDP module.
- Fix the 3 screws to PDP module after removing theabove mentioned units.
6. Removing the optical filter
The front cabinet includes optical filter to protect the panel
from damage, to improve picture quality, or prevent
exposure of interference.
- Remove the 4 screws ,
- Unscrew the 4 screws ,
- Remove the 6 screws ,
- Remove the 4 screws
- Remove 2 hexagonal screws to remove the PDP
module.
Note: cannot clean Panel surface or Optical Filter after
assembling Panel Module, if caught the dust to them.
25
29
28
27
26
22
2423
2221
2324
2222
21 21
22
2525
First issue 04 / 02 7
26 26 26 26
27 27 27 27
28
28
28
29
29
28
28
28
29
29
5/14/2018 32WP95E - slidepdf.com
http://slidepdf.com/reader/full/32wp95e 8/17
- Remove the 6 screws and pu ll the top bracket ,
- Remove the 4 screws and pull the r ight bracket,
- Remove the 6 screws and pull the bottom bracket,
- Remove the 4 screws and pu ll the le ft bracket,
7. Removing the power module
When replacing the PDP module, the power module must
be remove from the old PDP module and reassemble on the
new one. Proceed as follow:
- Remove the 7 screws (3x6),
Note:
The optical filter is easy to be damaged. Do not touch
directly by hand. If there is dust, remove it by watery
neutral detergent.
- Cut and remove the wire band ,
- Disconnect the wire from power module,
- Take out the power unit.
35
36
34
38
33
32
31
30
8 First issue 04 /02
30
Gasket
32
3133
34
34 34
34
35
34
34 34
36
37
38
5/14/2018 32WP95E - slidepdf.com
http://slidepdf.com/reader/full/32wp95e 9/17
First issue 04 / 02 9
8. Removing the flat cables
This set use 3 kinds of connector for flat cable. To remove a
cable and not to damage it, proceed as below.
Type A:- Lift up the hook on both sides and pull the flat cable to
disconnect it.
Type B:
- Slide the hook on both sides and pull the flat cable to
disconnect it.
Type C:
- Pull the flat cable to disconnect it.
BOARD LOCATION
MAINAUDIO
PC TERMINALPOWER SWITCH RC RECEIVER
SENSOR POWER
Cable
Cable
Cable
Type A
Type B
Type C
5/14/2018 32WP95E - slidepdf.com
http://slidepdf.com/reader/full/32wp95e 10/17
WIRING DIAGRAM
10 First issue 04 /02
M T G F A N
C O R E F E R R I T E
C O R E F E R R I T E
C O R E
F E R R I T E
C O R E
F E R R I T E
C O R E F E R R I T E
5 1
9 V
6 V
G N D
3 4 V
1 2 V
1 2 V
1 2 V
G N D
G N D
G N D
1
1 0
2
1
- 5 V
G N D
3
1
5 5
1 1
N E U T
L I V E 2
1
L I V E
N E U T
2
1
N E U T
L I V E
5 0
5 0
5 0
5 0
1
1
1
1
1 2
1 2
1 0
1 0
1 0
1 0
1
1
1
1
- 5 V G N D
G N D
6 V
9 V
G N D
G N D
G N D 1 2 V
1 2 V
1 2 V
1 0
2
1
1
3 4 V
G N D
3 . 3
V S T A N B Y
5 V
S T A N B Y
5 1
A C ( N E U T )
A C ( L I V E )
3 7 0 V
G N D
6 3
3
1
1
F G
3
3
1
1
F G
3 6
3 5
3 4
3 3
3 2
3 1
3 0
2 9
2 8
2 7
2 6
2 5
2 4
2 3
2 2
2 1
2 0
1 9
1 8
1 7
1 6
1 5
1 4
1 3
1 2
1 1
1 0 9 8 7 6 5 4 3 2 1
3 6
3 5
3 4
3 3
3 2
3 1
3 0
2 9
2 8
2 7
2 6
2 5
2 4
2 3
2 2
2 1
2 0
1 9
1 8
1 7
1 6
1 5
1 4
1 3
1 2
1 1
1 0
9 8 7 6 5 4 3 2 1
K R S P A
K 1 6 Y A
C N 1 B K
G N D 2
K G N D 1
K 3 U A
K P O W 3 A
K S P 9 0 1
A
K S P 9 0 2 A
L F 9 0 1 A
C N 1 A
C N 1 - K
7 S K
3 U - K
6 U
K P
O W E R 3
K 3 T - K
8 T
K P
O W 2
K 3 D - 8
D
K 1 0 A - 8
A
K 1 0 K - 8
K
K 1 0 C 1 9 C
K 1 3 N 1 9 N
EL901
EL902
F N 9 0 1
F N 9 0 2
K 8 W K 1 9 R C
K 8 P W
A C I N
L F 9 0 1
M 9 0 1
K P O
W 3
K P O W E R 3
K 6 C
K 8 W
K 3 S T
K 1 9 R C
K 8 P O 2
K P O W 2
K S E N S 1
K S E N 1
K F A N 2
K F A N 1
K 1 9 S W P
K 8 P W
K 8 T
K 6 U
K 3 U
K 3 T
K 1 9 C
K 8 K
K 8 D
K 3 D
K 1 0 C
K 1 9 N
K 1 3 N
K 1 0 K
C N 6 2
C N 6 1
C N 6 3 C N
1
K L S P
K R S P
K 1 6 Y
K 1 6 Z
K P O W E R 1
K 8 X
K 7 S
K 8 A
K 1 0 A
A C
c o r d
N o i s e
f i l t e r
1
1
+
-
+
-
2 0
1 9
1 8
1 7
1 6
1 5
1 4
1 3
1 2
1 1
1 0
9
2 0
1 9
1 8
1 7
1 6
1 5
1 4
1 3
1 2
1 1
1 0
9
2
1
4
3 5 7
6 8
2
1
4
3 5 7
6 8
A U D I O
M A I N
P C
R C
S W
POWERSW
SENSOR
L O G I C
B O A R D
A C
- D C
B O A R D
D C
- D C
F A N
5/14/2018 32WP95E - slidepdf.com
http://slidepdf.com/reader/full/32wp95e 11/17
First issue 04 / 02 11
DIAGNOSTIC
This set is equipped with a self-diagnostic function to detect power, audio amplifier, temperature and fan default. The trouble can beidentified either by a flashing of the tricolour led or by a message displayed on screen.
Start
Stop
The set switches in standby mode
Does the message "Warning! Internal fan is trouble, not working properly" appears on
screen for 10 seconds every 10 minutes?
Is the power LED flashing yellow
once?
Is the power LED flashing red twice?
Is the power LED flashing green twice?
Failure in fan'speripheral area
of the set
Check IC071 andits peripheralcomponents
on AUDIO PCB
Check Fan andSensor controlcircuit (IC1821)on AUDIO PCB
Check 9V, 12Vand 30V lineson AUDIO PCB
Check 9V, 12Vand 30V lineson AUDIO PCB
Is the power LED flashing green
three times?
No
No
Yes
Yes
No
Yes
No
Yes
Yes
Does the set switch off, after displaying the
message:"Warning! Internal
temperature is too high" for 10 seconds?
Temperature fail
No
Yes
Check 5V line on AUDIOPCB and 3.3V, 2.5V and
2.5VST lines on MAIN PCBIs the power LED flashing green once?
No
No
Yes
: Power Fail Line 3.
: Power Fail Line 1.(see next page)
Notes:In case of overlapped fails, flashing sequences are repeated in turn.If power fail is detected 3 times in 15 minutes, the monitor will stop operating.If the AC cord is unplugged, the information of fails will disappear.
5/14/2018 32WP95E - slidepdf.com
http://slidepdf.com/reader/full/32wp95e 12/17
12 First issue 04 /02
POWER BLOCK DIAGRAM
5/14/2018 32WP95E - slidepdf.com
http://slidepdf.com/reader/full/32wp95e 13/17
First issue 04 / 02 13
PCR
G
B
MAIN
R
G
B
IC1124RGB SWITCH
IC207A/D CONVERTER
IC601RGB MATRIX
IC301MAIN SCALER
IC751LVDSINTERFACE
PDPPANELMODULE
RGB RGB
RGB
RGB
1(R)3(G)5(B)
7(R)15(G)22(B)
211915
RGB
PC
DVI
IC1301
RGB RGB
R/L
AUDIO
IC001AUDIO CONTROL(Fixed)
22(L),21(R)
16(L),15(R)
25(L),20(R)23(L),22(R)
IC071MAIN DIGITALAMP
+-
L
R
SPEAKER X2
10(L),13(R)
*
* Depending on DVI version, this audio line is bypassed to avoid the Audio Control IC.
GENERAL BLOCK DIAGRAM
5/14/2018 32WP95E - slidepdf.com
http://slidepdf.com/reader/full/32wp95e 14/17
14 First issue 04 /02
It is necessary to enter the Service Mode in order to carry outalignment of the set. Most adjustments must be made withthe RCU.
The following operations must be done quickly:• Switch the monitor on,• Press and hold the MENUbutton on the monitor,
• Using the remote control, press the EXIT button andrelease it.
• Release the MENU button of the monitor.• Press the MUTE button.• The service mode menu appears on the screen.
Using the remote control:• Press the / buttons to select the adjustment.• Press the button to select the value of the adjustment.
• Press the / buttons to adjust the value.• Press the button to select the name of another adjustment.
NB : the value of the adjustment is memorized automaticallyinto a non volatile memory.
• To exit the service mode menu press the power ON/OFFbutton on the monitor.
ACCESSING SERVICE MODE
3 EXITING FROM SERVICE MODE
2 NAVIGATION INSIDE THE SERVICE MODE
MENUOK
I NP UT V OL UM E
MENU Button
Main
Sub
32035
019
PDP Time 001396
Feb-Dynamic
Cont0 63 (3F)
Main
Sub
32
035
019
PDP Time
001396
Feb-Dynamic
Cont0 63 (3F)
Main
Sub
32
035
019
PDP Time
001396
Feb-Dynamic
Cont0 63 (3F)
SERVICE MODE
1
ADJUSTMENTS
All circuits have been adjusted in factory to make the monitor operating basically. These adjustments are controlled by the CPU(IC801) and memorizzed into the memory (IC808). When the audio board or the memory is replaced, the fixed data must be set andthe white balance adjusted.
1. Setting the fixed data
- Make sure the received signal is good quality.
- Enter the service mode as above mentioned,- Check the fixed data are corresponding to the data table
on next pages and adjust if necessary,
- Exit the service mode.
2. Adjusting the white balance
- Input signal 1.0Vpp/75 Ω terminated,
- White pattern,
- Screen size : full,
- Picture image level : natural
- Enter the service mode,
- Select alternatively adjustment n°69 (Cont FEB - red),
n°70 (Cont FEB - green) and n°71 (Cont FEB - blue),
- Adjust alternatively to obtain a proper white balance,- After adjustment, confirm the white balance with a normal
picture.
3. PDP power supply
The PDP module stores voltage information and send it to
the power supply assembly to obtain the best voltage.
Therefore it is not necessary to adjust the PDP power
supply.
5/14/2018 32WP95E - slidepdf.com
http://slidepdf.com/reader/full/32wp95e 15/17
First issue 04 / 02 15
0 FEB-Dynamic Contrast 63 0 63 Picture Menu (Dynamic)1 Brightness 31 0 632 Color 45 0 633 Tint 0 -31 324 --------------- -- -- --5 FEB-Standard Contrast 50 0 63 Picture Menu (Natural)6 Brightness 31 0 637 Color 31 0 638 Tint 0 -31 329 --------------- -- -- --10 FEB-Cinema Contrast 31 0 63 Picture Menu (Cinema)11 Brightness 31 0 6312 Color 26 0 6313 Tint 0 -31 3214 --------------- -- -- --15 PC Graphic Contrast 63 0 63 Picture Menu (Graphic)
16 Brightness 31 0 6317 Color 45 0 6318 Tint 0 -31 3219 --------------- -- -- --20 PC Standard Contrast 40 0 63 Picture Menu (Standard)21 Brightness 31 0 6322 Color 31 0 6323 Tint 0 -31 3224 --------------- -- -- --25 PC-Text Contrast 31 0 63 Picture Menu (Text)26 Brightness 31 0 6327 Color 26 0 6328 Tint 0 -31 3229 --------------- -- -- --30 Sub Menu FEB Contrast 60h 00h FFh FEB Input31 Brightness 39h 00h FFh32 Color-S 78h 00h FFh S-Video33 --------------- -- -- --34 Tint 00h 80h 7Fh35 --------------- -- -- --36 Sub Menu PC Contrast 60h 00h FFh37 Brightness 39h 00h FFh38 Color-S 80h 00h FFh39 Tint 00h 80h 7Fh40 --------------- -- -- --51 Color Temp H-FEB Red DCh 00h FFh FEB Color Temperature (High)52 Green F0h 00h FFh
53 Blue FFh 00h FFh54 Color Temp M-FEB Red FFh 00h FFh FEB Color Temperature (STD)55 Green FFh 00h FFh56 Blue FFh 00h FFh57 Color Temp L-FEB Red FFh 00h FFh FEB Color Temperature (Low)58 Green EBh 00h FFh59 Blue CDh 00h FFh60 Color Temp H-PC Red DCh 00h FFh PC Color Temperature (High)61 Green F0h 00h FFh62 Blue FFh 00h FFh63 Color Temp M-PC Red FFh 00h FFh PC Color Temperature (STD)64 Green FFh 00h FFh65 Blue FFh 00h FFh
No. NoteAdjustment NameData Area
Adjustment ItemInitialData
Min Max
All data except in gray box area is fixed. Do not change for correct operating.Data in gray box area is initial. Can be set according to adjustment information.
5/14/2018 32WP95E - slidepdf.com
http://slidepdf.com/reader/full/32wp95e 16/17
16 First issue 04 /02
66 Color Temp L-PC Red FFh 00h FFh PC Color Temperature (Low)67 Green EBh 00h FFh68 Blue CDh 00h FFh
69 Cont FEB Red FFh 00h FFh White Balance Adjustment70 Green F4h 00h FFh71 Blue D2h 00h FFh72 Bright FEB Red 80h 00h FFh Black Balance Adjustment73 Green 80h 00h FFh74 Blue 80h 00h FFh75 Cont PC Red 00h 00h FFh W/B (Differential Data to FEB)76 Green 00h 00h FFh77 Blue 00h 00h FFh78 Bright PC Red 00h 00h FFh B/B (Differential Data to FEB)79 Green 00h 00h FFh80 Blue 00h 00h FFh93 Sharpness-PC Sharpness 0 0 10 Filter
94 Sharpness-FEB1-50 Sharpness 10 0 10 Filter95 Sharpness-FEB1-60 Sharpness 6 0 10 Filter111 PDP COLOR8 PDP Internal Pattern Display ( Key)112 PDP WHITE PDP Internal Pattern Display ( Key)113 Side Bar 81 0 225 Brightness od Side Bar
No. NoteAdjustment NameData Area
Adjustment ItemInitialData
Min Max
5/14/2018 32WP95E - slidepdf.com
http://slidepdf.com/reader/full/32wp95e 17/17
The description and characteristics given here are of informative significance only, and non committal. To keep up the high quality of our products, we reserve the right tomake any changes or improvement without previous notice. • Les descriptions et caractéristiques figurant sur ce document sont données à titre d'information et nond'engagement. En effet, soucieux de la qualité de nos produits, nous nous réservons le droit d'effectuer, sans préavis, toute modification ou amélioration. • DieBeschreibungen und Daten in dieser Anleitung dienen nur zur Information und sind nicht bindend. Um die Qualität unserer Produkte ständig zu verbessern, behalten wir unsdas Recht auf Änderungen vor. • Le descrizioni e le caratteristiche date su questo documento sono fornite a semplice titolo informativo e senza impegno. Ci riserviamo ildiritto di eseguire, senza preavviso, qualsiasi modifica o miglioramento. • Las descripciones y características que figuran en este documento se dan a título de información yno de compromiso. En efecto, en bien de la calidad de nuestros productos, nos reservamos el derecho de efectuar, sin previo aviso, cualquier modificación o mejora. T
H O M S O N
m u l t i m e d i a S a l e s E u r o p e - S . A . a u c a p i t a l d e
3 0 0 0 0 0 0 0 - S i è g e : 4 6 , q u a i A l p h o n s e L e G a l l o 9 2 1 0 0 B o u l o g n e F r a n c e - R C S N a n t e r
r e B 3 2 2 0 1 9 4 6 4
THOMSON multimediaSales France46, quai Alphonse Le Gallo92648 Boulogne cedex
Tel. : 01 41 86 60 00Minitel : 3616 ou 3623 TCEDSInternet : http://www.thomson.fr
THOMSON multimedia
Sales UK Limited30 Tower ViewKings Hill, West MallingKent ME19 4NQ (England)Tel. : 44 (0) 173 252 0920
THOMSON multimediaSales Italy S.p.A.Via Leonardo da Vinci,4320090 Trezzano sul naviglio (Milano)Tel. : (02) 48 414 111
THOMSON multimediaScandinavia ABFlorettgatan 29 CS-25467 Helsingborg (Sweden)Tel. : 042 25 75 00
THOMSON multimediaSwitzerlandSeewenweg 5CH-4153 ReinachTel. : (61) 716 96 60
THOMSONConsumer Electronics Polandul.Gen.L. Okulickiego 7/905-500 Piaseczno (Varsovie)Tel. : (22) 757 10 80
THOMSON multimediaHungary KFTLajos u. 78. II.em.H-1036 BudapestTel. : 00 36 14 5334/80
THOMSON multimediaCzech s.r.o.ul. Dopravaku - dum Genius 1Dolni ChabryCZ - 18400 Prague 8Tel. : (2) 688 67 70
THOMSON multimediaSales Germany GmbH & Co oHGKarl-Wiechert-Allee 7430625 Hannover
THOMSON multimediaSales SpainAvenida Isla Graciosa, 1Edificio ÁncoraParque Empresarial La Marina28700 San Sebastián de los Reyes (Madrid)Tel. : (91) 384 14 19
THOMSON multimediaSales PortugalAvenida da Boavista, 35214106 PortoTel. : (2) 26 18 76 41
This technical documentation is for use by maintenance technicians onlyDocumentation technique exclusivement destinée aux professionnels de la maintenanceDiese Angaben und Hinweise sind ausschließlich für den Service des Fachhändlers bestimmtDocumentazione tecnica destinata esclusivamente ai tecnici dell'assistenzaDocumentación técnica destinada exclusivamente a los profesionales de mantenimiento
top related