060070 meridian gyrocompass
Post on 24-Oct-2014
234 Views
Preview:
TRANSCRIPT
Contents
CAUTIONARY NOTICESYour attention is drawn to the following cautionary notices that apply throughout this Manual.
WARNINGThe Meridian Gyrocompass weighs 15.5kg. To avoid personal injury, take proper precautions if you lift or move the equipment.
WARNINGThere is a danger of serious injury from voltages inside the Meridian Gyrocompass. Do not remove the gyrocompass cover unless you have the necessary skills and experience to perform maintenance work on a system of this nature. Always power-off the system before you remove the cover for maintenance work.Observe all local safety regulations as you work on the equipment. Reconnect the safety grounding straps and refit all safety covers to the equipment before you power-on the system.
WARNINGThe Meridian Gyrocompass should be supplied with power from an SELV source as defined in IEC/EN 60950. The power supply source should be switched and protected by a suitable circuit breaker.
CAUTIONThe Meridian Gyrocompass includes precision components and bearings. To avoid causing damage to any part of the System, handle all items with care.
Retain the original packing cases so that you can use them to transport the system when necessary. You will void the warranty if you use improper packing during transportation.
CAUTIONSevere damage to the Meridian Gyrocompass can occur if you move the gyrocompass while the rotor is still spinning without the servo system in operation.
Note that the gyro rotor continues to spin for approximately five minutes after you power-off the system.
To avoid potential damage to the Meridian Gyrocompass, always allow a period of five minutes after power-off for the gyro rotor to come to rest before you attempt to move the gyrocompass.
DPN 060070 © TSS (International) Ltd Issue 3.11 Page 1 of 6
Meridian Gyrocompass
CAUTIONDuring operation, the gyrocompass must remain level to within ±45°. If it experiences tilt greater than 45° in any direction, it will ‘topple’.
Never apply a tilt of more than 45° with the gyro rotor spinning or during the gyrocompass initialisation procedure. Note that the gyro rotor continues to spin for approximately five minutes after you power-off the System.
CAUTIONIf you install the gyrocompass in an enclosed space, make certain there is sufficient ventilation and circulation of free air to allow effective cooling.
CAUTIONPerform maintenance instructions only if you have the skills and experience required, and only when necessary. Inappropriate tampering with the internal controls and components of the gyrocompass can lead to damage or serious performance degradation.NEVER open the gyrocompass cover or make any adjustments inside the gyrocompass unless you are entirely confident in your actions.
CAUTIONRemove power from the gyrocompass before making any connections to external equipment.
CAUTIONYou will void the warranty if you make any modifications to this equipment without prior permission from TSS (International) Ltd.
DO NOT modify this equipment in any way without obtaining permission from TSS (International) Ltd.
CAUTIONYou will void the warranty if you operate the gyrocompass outside the environmental conditions detailed in Section 4 and in BS EN 60945.
Page 2 of 6 Issue 3.11 © TSS (International) Ltd DPN 060070
Contents
CONTENTS
1 INTRODUCTION 1–11.1 System Description 1–31.1.1 Gyrocompass 1–31.1.2 Remote Control Unit 1–41.1.3 Auxiliary Inputs 1–51.1.4 Heading Outputs 1–5
1.2 Principle of Operation 1–5
2 INSTALLATION 2–12.1 Unpacking and Inspection 2–22.2 Physical and Electrical Installation 2–32.2.1 Selecting a location 2–32.2.2 Gyrocompass installation 2–42.2.3 External Remote Control Unit 2–102.2.4 Set the Gyrocompass DIP Switches 2–11
2.3 Alignment 2–132.4 Final Gyrocompass Installation Tests 2–132.5 Installation Drawings 2–14
3 OPERATING INSTRUCTIONS 3–13.1 Control Features 3–23.2 Initial Power-on 3–33.3 Operating Procedure 3–43.3.1 Latitude correction 3–43.3.2 Speed correction 3–53.3.3 DG operating mode 3–5
3.4 Error Modes 3–63.4.1 Loss of GPS 3–63.4.2 Loss of speed log 3–63.4.3 Gyrocompass system warnings and failures 3–7
3.5 Operating Considerations 3–93.5.1 General Operating Considerations 3–93.5.2 Corrections for Speed and Latitude 3–103.5.3 Operating at Extremes of Latitudes 3–103.5.4 Operating Considerations for Vessel Dynamics 3–10
4 TECHNICAL DATA 4–14.1 Specifications 4–14.1.1 Power Requirements 4–14.1.2 Performance (definitions as in ISO 8728) 4–14.1.3 Compensation 4–14.1.4 Environment 4–14.1.5 Signal Inputs 4–24.1.6 Signal outputs 4–24.1.7 Dimensions and Weight 4–24.1.8 Listener load requirement 4–34.1.9 Talker drive capability 4–3
DPN 060070 © TSS (International) Ltd Issue 3.11 Page 3 of 6
Meridian Gyrocompass
4.1.10 Standards 4–34.2 Data Formats 4–44.2.1 IEC 61162 Serial Data Formats – General information 4–54.2.2 Inputs 4–64.2.2.1 IEC 61162 input signals 4–64.2.2.2 Pulsed input 4–10
4.2.3 Outputs 4–114.2.3.1 IEC 61162 output signals 4–11
4.2.4 IEC 61162 sentence with Checksum 4–154.2.5 Other Output Formats 4–164.2.5.1 Course Recorder Output 4–164.2.5.2 Synchro Output 4–164.2.5.3 Resolver Output 4–164.2.5.4 Stepper S-Code 4–174.2.5.5 Rate of Turn 4–17
5 MAINTENANCE 5–15.1 Built-in Test Equipment 5–15.1.1 Azimuth Drift Adjustment 5–25.1.2 Azimuth Bias Adjustment 5–3
5.2 Test Connector 5–35.3 Diagnostic Output Sentence 5–6
Page 4 of 6 Issue 3.11 © TSS (International) Ltd DPN 060070
Contents
TABLE OF AMENDMENTS
Old Issue New Issue Date Details
- 2.0 11 May 2000 New release.
2.0 2.0A 12 Dec 2000 Corrected identification of Azimuth Bias potentiometer and other details. Include DIP switch default settings.
2.0A 2.0B 1 Mar 2001 Modify power connection details.
2.0B 2.0C 23 Apr 2001 Add notification to avoid product modifications.
2.0C 3.0 Aug 2002 Substantial amendments to reflect product enhancements.
3.0 3.1 Sept 2002 completion of enhancement features including compliance with IEC 61162.
3.1 3.2 Jan 2003 Minor amendments and description of Diagnostic Output Sentence.
3.2 3.3 Feb 2003 Modification to specifications and addition of Appendix B to demonstrate Certificate of Type Approval.
3.3 3.4 Mar 2003 Minor amendments to a display warning and a note referring to confirming software release.
3.4 3.5 July 2003 Note added regarding modification kit available for alternative orientations when attempting correct speed compensation.
3.5 3.6 August 2003 Minor amendments to specifications throughout.
3.6 3.7 March 2004 Amendments to alarm warning / failure designation.
3.7 3.8 March 2005 Details for High Speed Craft (HSC) operation.
3.8 3.9 May 2005 Updated Distribution board connections and drawing.
3.9 3.9.1 September 2005 Added paragraph to section 3.5.4 explaining potential conflicts with earth connections on distribution board for the HSC.
3.9.1 3.10 June 2006 Revised Company Logo
3.10 3.11 January 2008 Replaced manual setting of DG Mode on distribution board with Alarm Acknowledgement functionality. This enables compatibility with the Compass Changeover System.
DPN 060070 © TSS (International) Ltd Issue 3.11 Page 5 of 6
Meridian Gyrocompass
Page 6 of 6 Issue 3.11 © TSS (International) Ltd DPN 060070
Introduction
1 INTRODUCTIONThe Meridian Gyrocompass is a master heading reference instrument that applies the characteristics of a dynamically tuned gyroscope and the effects of gravity and earth rotation to provide a true north reference.
The Meridian Gyrocompass specification makes the System ideal for installation and operation on board vessels of almost any size and in a wide range of applications.
Among the standard features of the Meridian Gyrocompass are:
❐ A short settling time
❐ Operation from a 24V DC electrical supply
This Manual is an important part of the Meridian Gyrocompass. It describes the System and contains full installation and operating instructions. You should retain the Manual with the System for use by personnel who will install and operate it.
Installation and operation of the Meridian Gyrocompass are not complex tasks. However, you should spend time to familiarise yourself with the contents of this Manual before you start to install or use the System. Time spent in identifying the task sequence now will ensure your System is operational in the minimum of time.
WARNINGSWhere appropriate, this Manual includes important safety information highlighted as WARNING and CAUTION instructions. You must obey these instructions:WARNING instructions alert you to a potential risk of death or injury to users of the System.
CAUTION instructions alert you to the potential risk of damage to the System.For your convenience, the Contents section includes copies of all the WARNING and CAUTION instructions included in this Manual.
Throughout this Manual all measurements conform to the SI standard of units unless otherwise indicated.
DPN 060070 © TSS (International) Ltd Issue 3.10 Section 1 Page 1 of 6
Meridian Gyrocompass
For your convenience, this Manual includes several sections, each of which describes specific features of the Meridian Gyrocompass:
You should read sections 1 and 2 before you attempt to install the System:Section 1 contains introductory notes and describes those items supplied as
standard.
Section 2 describes how to select a suitable location for the gyrocompass. This section includes full instructions to install the System and connect it to external equipment.
You should read sections 3 and 4 before you use the System:Section 3 describes how to operate the Meridian Gyrocompass.
Section 4 includes the System specifications and descriptions of the data formats.
You should read sections 5 if you suspect a fault on the System:Section 5 describes how to use the internal 60-way test connector and explains
how to conduct simple adjustments with the gyrocompass housing removed.
This Manual also contains the following appendices:Appendix A explains how a gyroscope can be made north seeking for use in a
gyrocompass.
Appendix B contains copies of Type Approval Certificates.
CAUTIONYou will void the warranty if you make any modifications to this equipment without prior permission from TSS (International) Ltd.DO NOT modify this equipment in any way without obtaining permission from TSS (International) Ltd.
Section 1 Page 2 of 6 Issue 3.10 © TSS (International) Ltd DPN 060070
Introduction
1.1 SYSTEM DESCRIPTIONThe Meridian Gyrocompass comprises two sub-assemblies:
❐ The gyrocompass housing
❐ The Remote Control Unit (RCU)
Figure 1–1 shows the combined gyrocompass housing with the RCU included as an integral unit.
The Meridian Gyrocompass applies dynamic tuning to settle automatically to the meridian. Due to the physical principles of a north-seeking gyrocompass, achievable accuracy depends on the operating latitude and the vessel dynamics. To optimise its performance, the Meridian Gyrocompass uses information supplied by external equipment, for example a GPS receiver and a speed log, to apply latitude and speed corrections.
Refer to Appendix A for a simplified explanation of the gyrocompass theory of operation.
1.1.1 GYROCOMPASSFigure 1–1: Gyrocompass housing with integral RCU
Figure 1–1 shows the gyrocompass housing, which contains the following items:
❐ True north seeking dynamically tuned precision gyroscope and gimbal suspension assembly.
❐ Power supply board.
❐ Digital and analogue control boards.
❐ RFI filter and distribution board.
It is a relatively simple operation to install the gyrocompass and you should be able to accomplish this quickly without the need for specialised personnel or equipment. However, note that the gyrocompass weighs 15.5kg and you must take due care when you lift and move it.
DPN 060070 © TSS (International) Ltd Issue 3.10 Section 1 Page 3 of 6
Meridian Gyrocompass
The care that you take when you align the gyrocompass housing with the surveyed fore-aft axis of the vessel will have a direct impact on the accuracy of heading measurements delivered by the System. Since the Meridian Gyrocompass is an ideal source of heading information for use by other systems on board, such as radars and satellite communication antennas, the accuracy of its heading measurements will have a wide impact throughout the vessel. You should therefore take care when you install and align the gyrocompass. Refer to Section 2 for full instructions to install, connect and align the Meridian Gyrocompass.
The only component available for user servicing is a 3.15A line fuse inside the gyrocompass housing. In case of failure, refer to Section 5 for instructions on fault diagnosis and maintenance.
1.1.2 REMOTE CONTROL UNITFigure 1–2: Remote Control Unit
The Remote Control Unit (RCU) provides all the functions and indicators necessary to control and operate the Meridian Gyrocompass.
The four-character LED can show a range of information:
❐ Heading in Degrees. 000.0 to 359.9
❐ Latitude. 80S to 80N
❐ Latitude Source
❐ Speed in Knots. 00 to 90
❐ Speed Source
❐ Alarms and Status information
❐ Separate LED indicators show Power On and Compass Ready conditions
Refer to Section 3 for instructions to operate the Meridian Gyrocompass.
Section 1 Page 4 of 6 Issue 3.10 © TSS (International) Ltd DPN 060070
Introduction
1.1.3 AUXILIARY INPUTSAuxiliary inputs may be used for the Meridian Gyrocompass to apply latitude and speed corrections.
Ideally, the Meridian Gyrocompass should accept latitude and speed information from external sources such as a GPS receiver or a speed log. However, you may supply this information manually if external sources are not available. The advantage of using GPS or a speed log to provide correction signals is that they allow automatic corrections to be applied without operator intervention.
Section 2 includes instructions to connect and configure the external sources of latitude and speed information.
Section 3 includes instructions to set the latitude and speed manually.
1.1.4 HEADING OUTPUTS
The Meridian Gyrocompass is a self-contained precision navigation instrument that is capable of supplying heading reference information simultaneously to a wide range of equipment on board the vessel. Throughout a typical vessel, applications that can use information supplied by the Meridian Gyrocompass include:
❐ Autopilot
❐ Radars
❐ GPS
❐ Radio direction finder
❐ Course plotter and recorder
❐ Satellite communication systems
❐ Satellite television
To support this wide range of equipment types, the Meridian Gyrocompass can supply heading information simultaneously through multiple channels using any of the common transmission formats.
Refer to Section 4 for a description of the available output channels and their data formats. Refer to Section 2 for details on how to interconnect to other equipment.
1.2 PRINCIPLE OF OPERATIONIn the absence of external influences, a free-spinning gyroscope will try to maintain a fixed orientation in space. The Meridian Gyrocompass exploits this property and uses gravity control and earth rotation to align the gyroscope spin axis with the meridian, i.e. the true north direction.
Refer to Appendix A for the general theory of gyrocompass operation.
DPN 060070 © TSS (International) Ltd Issue 3.10 Section 1 Page 5 of 6
Meridian Gyrocompass
Section 1 Page 6 of 6 Issue 3.10 © TSS (International) Ltd DPN 060070
Installation
2 INSTALLATIONTo obtain the best performance from the Meridian Gyrocompass you must take care when you install and connect it. This section includes all the information and instructions you will need to complete these tasks.
You should read this section carefully and understand the important instructions that it contains before you begin to install or connect the equipment.
2.1 Unpacking and Inspection Page 2Explains the inspection checks that you should perform as you unpack the Meridian Gyrocompass.
2.2 Physical and Electrical Installation Page 3Choose a suitable location to install the Meridian Gyrocompass. Connect the system to an electrical supply and to external equipment.
2.3 Alignment Page 13The care that you take as you align the Meridian Gyrocompass with the fore-aft datum on the vessel will have a direct influence upon its accuracy.
DPN 060070 © TSS (International) Ltd Issue 3.11 Section 2 Page 1 of 18
Meridian Gyrocompass
2.1 UNPACKING AND INSPECTION
WARNINGThe Meridian Gyrocompass weighs 15.5kg. To avoid personal injury, take proper precautions if you lift or move the equipment.
CAUTIONThe Meridian Gyrocompass includes precision components and bearings. To avoid causing damage to any part of the System, handle all items with care.
Retain the original packing cases so that you can use them to transport the system when necessary. You will void the warranty if you use improper packing during transportation.
CAUTIONSevere damage to the Meridian Gyrocompass can occur if you move the gyrocompass while the rotor is still spinning without the servo system in operation.
Note that the gyro rotor continues to spin for approximately five minutes after you power-off the system.
To avoid potential damage to the Meridian Gyrocompass, always allow a period of five minutes after power-off for the gyro rotor to come to rest before you attempt to move the gyrocompass.
The Meridian Gyrocompass undergoes a full series of electrical and mechanical tests during manufacture and before dispatch. The packing case has a special design to protect the contents against shock during transit so that the equipment should arrive without damage or defect.
As soon as possible after you have received the system, check all items against the shipping documents. Inspect all sub-assemblies carefully to check for any damage that may have occurred during transportation. If you see any damage file a claim with the carrier and immediately notify TSS (International) Ltd.
To avoid loss or damage to any components of the system, store all sub-assemblies safely in the packing case until you need to install them. Obey the storage temperature limits listed in Section 4.
Notify TSS (International) Ltd immediately if there are any components missing from the shipment.
The title page of this Manual lists the contact details for TSS (International) Ltd.
Section 2 Page 2 of 18 Issue 3.11 © TSS (International) Ltd DPN 060070
Installation
2.2 PHYSICAL AND ELECTRICAL INSTALLATION2.2.1 SELECTING A LOCATIONThere are certain guidelines that you should follow to install the Meridian Gyrocompass successfully:
CAUTIONDuring operation, the gyrocompass must remain level to within ±45°. If it experiences tilt greater than 45° in any direction, it will ‘topple’.
Never apply a tilt of more than 45° with the gyro rotor spinning or during the gyrocompass initialisation procedure. Note that the gyro rotor continues to spin for approximately five minutes after you power-off the System.
❐ The gyrocompass weighs 15.5kg. Choose a mounting location that is level, flat and sufficiently strong to support the unit without flexing or experiencing extreme vibration. The mounting location can be open, as on a chart table, or enclosed within a cabinet.
CAUTIONIf you install the gyrocompass in an enclosed space, make certain there is sufficient ventilation and circulation of free air to allow effective cooling.
❐ Choose a location that protects the Meridian Gyrocompass from damage.
❐ Do not install or operate the Meridian Gyrocompass where the ambient temperature could fall below 0°C or rise above +45°C, or where rapid changes of temperature can occur.
❐ Do not install the Meridian Gyrocompass close to strong mechanical or electrical noise sources, or in a location susceptible to vibration or shock.
❐ Allow a minimum distance of 0.4m between the gyrocompass housing and any standard magnetic compasses.
❐ Choose a location that allows convenient access to install, connect and service the Meridian Gyrocompass. Refer to Figure 2–6 for clearance dimensions.
DPN 060070 © TSS (International) Ltd Issue 3.11 Section 2 Page 3 of 18
Meridian Gyrocompass
2.2.2 GYROCOMPASS INSTALLATIONYou must align the Meridian Gyrocompass so that its fore-aft axis is parallel to the fore-aft datum on the vessel. Any misalignment between the gyrocompass housing and the vessel will have a direct effect on the accuracy of heading measurements delivered by the system.
To install the Meridian Gyrocompass you will need the following tools:
❐ Screwdriver 5.5mm × 150mm
❐ Screwdriver 3mm × 75mm
❐ Nut spinner 5.5mm
❐ 8.5mm drill
❐ 3 x M8 bolts of suitable length complete with washers and nuts
❐ Combination spanner 10mm
❐ Adjustable spanner opening to at least 33mm
❐ Suitable cables for the installation as indicated in Table 2–1 .
There should be no need to remove the gyrocompass cover during installation. You may gain access to make signal connections by removing the gland plate assembly, comprising the Gland Plate and the Distribution Board. There is a removable panel on the top of the gyrocompass that allows access to the internal DIP switches and a 60-way test connector.
1. During installation you must align the Meridian Gyrocompass so that its fore-aft axis is parallel with the fore-aft datum on the vessel. It is not necessary for the gyrocompass to be on the vessel centre line. There are alignment marks on the base of the Meridian Gyrocompass to help you achieve the correct alignment.
2. Three elongated securing holes machined into the gyrocompass base allow you to make fine adjustments to alignment after installation. With the gyrocompass positioned accurately, mark the supporting surface with the centre positions for the three securing holes. Refer to Figures 2–5 and 2–6 for dimensions.
3. Remove the gyrocompass and drill three 8.5mm diameter holes, using the marks you have just made on the supporting surface as hole centres. Deburr the holes and remove any swarf.
Table 2–1: Suitable cable types
Purpose Suitable cable
Power supply 7/0.5mm (1.5mm2) HOFR sheathed to BS6883
Synchro heading outputResolver heading outputStepper S-code output
7/0.4mm (1.0mm2) butyl or EP rubber insulated, CSP sheathed, wire braided and CSP oversheathed.
Serial data heading outputSerial data speed inputSerial data latitude input
1/0.85mm (0.6mm2) twisted pair, butyl or EP rubber insulated, CSP sheathed, wire braided and CSP oversheathed.
Section 2 Page 4 of 18 Issue 3.11 © TSS (International) Ltd DPN 060070
Installation
4. Reposition the gyrocompass and align it to the fore-aft datum. Use three M8 bolts with washers and nuts to secure the gyrocompass in position.
5. Connect a 24V electrical supply (acceptable range 18V to 36V DC) to the Meridian Gyrocompass at J1, the three-pin power inlet on the Gland Plate. Figure 2–1 shows the Gland Plate.
To prevent any possibility of damage to the gyrocompass while the vessel is moving it is recommended that an uninterruptable electrical supply is used to power the Meridian Gyrocompass.
6. Connect the ship’s safety ground to the earthing stud adjacent to the power connector.
Figure 2–1: Gyrocompass gland plate
CAUTIONRemove power from the gyrocompass before making any connections to external equipment.
Fuse
3.15AF
Compass Min. Safe Dist.
Build Standard No.
Serial No.
Mfg. Date
m
Watford, England.
CAUTION
Before removing the cover or the RCU
unit, remove the gland plate and
disconnect the RCU cable (TB1/17-22)
from the distribution board.
Gland plate release screws
Cover plate release screws
DPN 060070 © TSS (International) Ltd Issue 3.11 Section 2 Page 5 of 18
Meridian Gyrocompass
7. Make all necessary signal connections to the Meridian Gyrocompass at the Distribution Board. The Distribution Board accepts open tails for all connections. Pass cables through available glands in the Gland Plate. Glands A, D, E, F and J (identified in Figure 2–5) accept cables up to 18mm diameter, while all other glands accept cables up to 14mm diameter. Refer to Figure 2–3, and Tables 2–3 and 2–4 for cable connection details.
8. To maintain EMC compliance, connect all the wire braiding on the cables to the M3 grounding posts on the inside surface of the Gland Plate as shown in Figure 2–2.
Figure 2–2: Termination of wire braided cables
9. Refit the Gland Plate, making certain there are no trapped wires or cables.
Section 2 Page 6 of 18 Issue 3.11 © TSS (International) Ltd DPN 060070
Installation
Figure 2–3: Gyrocompass distribution board
Table 2–2: J1 – Power supply input pin details
Pin Description
1 Protective ground
2 +24V DC
3 0V
T B 6T B 5 T B 8T B 7
T B 4
DPN 060070 © TSS (International) Ltd Issue 3.11 Section 2 Page 7 of 18
Meridian Gyrocompass
Table 2–3: Input Signals
Signal description Signal type Distribution Board connector
Alarm Acknowledgement Voltage free contact close TB1/1(N/O) TB1/2 (CC)
GPS input IEC 61162 RS232 TB1/3 TB1/4 (0V)
GPS input IEC 61162 RS422 TB1/5 (A) TB1/6 (B)
Log input IEC 61162 RS232 TB1/7 TB1/8 (0V)
Log input IEC 61162 RS422 TB1/9 (A) TB1/10 (B)
Log OK TB1/11 TB1/12 (0V)
Log TTL pulses TB1/13 (+) TB1/14 (0V)
Log relay Voltage free contact close TB1/15 (+) TB1/16 (0V)
RCU 24V in TB1/17 (+) TB1/18 (–)
RCU On/Off TB1/19 (N/C) TB1/20 (ON)
RCU Communications RS422 TB1/21 (S+) TB1/22 (S-)
Rx Spare – TB1/23 TB1/24 (0V)
Section 2 Page 8 of 18 Issue 3.11 © TSS (International) Ltd DPN 060070
Installation
Table 2–4: Output Signals
Signal description Signal type Distribution Board connector
Channel 2 IEC 61162 RS232 (all data) TB2/1 TB2/2 (0V)
Channel 1 IEC 61162 RS232 (all data) TB2/3 TB2/4 (0V)
Channel 2 IEC 61162 RS422 (all data) TB2/5 (B) TB2/6 (A) TB4 (C)
Channel 1 IEC 61162 RS422 (all data) TB2/7 (B) TB2/8 (A) TB4 (C)
Heading TTL S-type TB2/9 (5V) TB2/10 (L1)TB2/11 (L2) TB2/12 (L3)TB2/13 (0V)
Heading Synchro/resolver TB2/14 (36V) resTB2/15 (26V) synTB2/16 (0V) syn/resTB2/17 (S1) synTB2/18 (S1) resTB2/19 (S2) syn/resTB2/20 (S3) syn/resTB2/21 (S4) res
Gyro fail Voltage free contact closure TB2/22 (CC)TB2/23 (normally closed, opens on failure)TB2/24 (normally open, closes on failure)
System Fail TTL TB2/25 TB2/26 (0V)
Gyro ready Voltage free contact closure TB2/27 (CC)TB2/28 (open when not ready, closes when ready)TB2/29 (closed when not ready, opens when ready)
Gyro ready TTL TB2/30 TB2/31 (0V)
Channel 2 IEC 61162 RS232 TB3/1 TB3/2 (0V)
Channel 2 IEC 61162 RS232 TB3/3 TB3/4 (0V)
Channel 2 IEC 61162 RS232 TB3/5 TB3/6 (0V)
Channel 2 IEC 61162 RS422 TB3/7 (B) TB3/8 (A) TB5 (C)
Channel 2 IEC 61162 RS422 TB3/9 (B) TB3/10 (A) TB5 (C)
Channel 2 IEC 61162 RS422 TB3/11 (B) TB3/12 (A) TB6 (C)
Channel 2 IEC 61162 RS422 TB3/13 (B) TB3/14 (A) TB6 (C)
Channel 2 IEC 61162 RS422 TB3/15 (B) TB3/16 (A) TB7 (C)
Channel 2 IEC 61162 RS422 TB3/17 (B) TB3/18 (A) TB7 (C)
Channel 2 IEC 61162 RS422 TB3/19 (B) TB3/20 (A) TB8 (C)
Channel 2 IEC 61162 RS422 TB3/21 (B) TB3/22 (A) TB8 (C)
Channel 2 IEC 61162 RS422 TB3/23 (B) TB3/24 (A) TB8 (C)
Rate of turn Analogue ±10V TB3/25 TB3/26 (0V)
Course recorder IEC 61162 RS232 TB3/27 TB3/28 (0V)
DPN 060070 © TSS (International) Ltd Issue 3.11 Section 2 Page 9 of 18
Meridian Gyrocompass
2.2.3 EXTERNAL REMOTE CONTROL UNITThe standard Meridian Gyrocompass has the Remote Control Unit (RCU) mounted integrally and available for immediate operation.
There may be applications where you prefer to install the RCU at some distance from the gyrocompass unit. A mounting kit, part number 929190, is available to use in these circumstances. The kit includes the following items:
❐ RCU housing
❐ Mounting bracket
❐ Blanking plate for the gyrocompass housing
There is no need to remove the gyrocompass cover to install the RCU externally:
1. Release and remove the four M3 screws at the corners of the RCU that secure it to the gyrocompass housing.
2. Remove the seven Gland Plate release screws marked A in Figure 2–1. Remove the Gland Plate. Note the connection sequence of the RCU cable at TB1/17–22 so that you can restore the same connections through the extension cable.
3. Disconnect the RCU cable at TB1/17–22.
4. Lift the RCU away from the gyrocompass.
The cable run between the gyrocompass and RCU must not exceed 100 metres.
5. Use the bracket with the mounting kit to fix the RCU to a desk or to a bulkhead. You may also flush mount the RCU in a panel. Choose a suitable location to mount the RCU:
❐ The mounting surface can be vertical or horizontal according to requirements.
❐ Avoid installing the RCU where it might experience severe shock or vibration.
❐ Choose a location for the RCU that allows a clear view of the display.
6. Use the two star knobs supplied to fit the RCU into the mounting bracket. Tilt the unit to a convenient viewing and operating angle and then lock it in place by tightening both star knobs.
7. Supply and fit a cable to connect the RCU to TB1/17–22 on the Distribution Board. The cable must have three screened twisted pairs and should not exceed 100 metres in length. Route the cable through a vacant cable gland on the Gland Plate and make the correct connections to the TB1 terminals.
8. Refit the Gland Plate and secure it in place using the seven release screws.
9. Fit the blanking plate to fill the gap left in the cover by the RCU.
Section 2 Page 10 of 18Issue 3.11 © TSS (International) Ltd DPN 060070
Installation
2.2.4 SET THE GYROCOMPASS DIP SWITCHES
1 There is a removable panel on top of the gyrocompass that allows access to the two internal DIP switches (shown in Figure 2–4) without the need to remove the main gyrocompass cover. Release and remove the three securing screws to lift off the panel.
2. Refer to Tables 2–5 and set the DIP switches carefully for the specific requirements of your installation. Do not adjust the settings of other preset controls inside the gyrocompass.
3. Refit the access panel to the top of the gyrocompass cover.
Figure 2–4: Location of DIP switches.
DPN 060070 © TSS (International) Ltd Issue 3.11 Section 2 Page 11 of 18
Meridian Gyrocompass
The DIP switch settings described in this table are only applicable to gyrocompasses fitted with software versions BPR 0161 (Main) and BPR 0114 (RCU) or later. If necessary, you can view the software versions of the main and the RCU processors by pressing both the Up and the Down selection buttons simultaneously. The display will toggle between indications of the main processor software version (with prefix 'M') and the RCU software (with prefix 'R'). The display will continue to toggle for several seconds after you release the buttons and will then return to the heading indication.
Table 2–5: SW1 and SW2 DIP switch settingsFactory default settings appear in bold and are marked with an asterisk in this table.
SW1 DIP Switches SW2 DIP Switches
Switch number
and settingFunction
Switch number
and settingFunction
1OnOffOnOff
2OnOnOffOff
Speed Log Input Type100 pulses per nautical mile200 pulses per nautical mile400 pulses per nautical mileLOG Serial Data*
1On
Off
Output Sentences typesAnalogue ROT Scaling +/- 60deg/minute = +/- 10VAnalogue ROT Scaling +/- 20deg/s = +/- 10V*
2OnOff
Channel 2 Heading decimal placesTwo decimal placesOne decimal place*
3OnOffOnOff
4OnOnOffOff
Channel 1 Baud / Update rate38k4 50Hz9600 10Hz4800 10Hz4800 1Hz
3OnOff
Channel 1 Checksum fieldChecksum transmittedNo Checksum transmitted*
4OnOff
Channel 2 Checksum fieldChecksum transmittedNo Checksum transmitted*
5OnOffOnOff
6OnOnOffOff
Channel 2 Baud / Update rate38k4 50Hz9600 10Hz4800 10Hz4800 1Hz
5 OnOffOnOff
6OnOnOffOff
Channel 1 Output SentencesAll Data (1Hz only)HDT + ROTROT onlyHDT only*
7OnOff
Channel 1 Heading Decimal placesTwo decimal placesOne decimal place*
7 OnOffOnOff
8OnOnOffOff
Channel 2 Output SentencesAll Data (1Hz only)HDT + ROTROT onlyHDT only*
8On
Off
Vessel DynamicsFor HSC applications(for serial numbers later than 3500)Standard Control Mode*
Notes: 1. If you set All Data Output Sentence, the update rate will default to 1Hz.2. For full IEC 61162 compliance, a checksum must be transmitted.
Section 2 Page 12 of 18Issue 3.11 © TSS (International) Ltd DPN 060070
Installation
2.3 ALIGNMENTIt is important to align the gyrocompass to the vessel accurately. Any misalignment between the housing and the vessel will appear directly as a fixed error in heading measurements. Because measurements from the Meridian Gyrocompass are available for use by diverse systems around the vessel, any misalignment between the gyrocompass and the fore-aft datum might have a significant impact in many other areas of application.
There are several methods you may use to align the gyrocompass to the vessel fore-aft datum:
❐ Align the gyrocompass to the fore-aft datum using a known reference line, such as a surveyed bulkhead or frame member. The marks on the gyrocompass base plate are precision indicators of the gyrocompass alignment orientation.
To achieve correct speed compensation, the gyrocompass must be orientated so that the gland plate faces the forward end of the vessel. Note that modification kits are available for alternative gyrocompass orientations.
❐ Use the services of a marine surveyor to align the gyrocompass precisely with the fore-aft datum.
Remove any residual misalignment by making minuscule adjustments to the gyrocompass mounting plate. When you have achieved perfect alignment, tighten the securing bolts fully to lock the gyrocompass in position.
2.4 FINAL GYROCOMPASS INSTALLATION TESTSAfter you have installed the gyrocompass and power supplies are available to it, perform the following installation tests:
1. Power-on the gyrocompass by following the instructions in sub-section 3.2. Wait for three hours before you perform the following tests.
2. Check the vessel heading against a known reference mark on a chart. Typically this could be the alongside position of the fitting-out dock. Alternatively, accurately survey an object at least five kilometres ahead of the vessel using the fore-aft line as a datum.
3. Check the displayed gyrocompass heading at intervals to make certain it is consistent with the surveyed vessel heading.
4. If there is an error larger than ±0.5°, re-check the vessel fore-aft datum to confirm that it is correct.
5. Check that all the repeaters are accurately aligned with the gyrocompass heading and make certain they maintain their alignment at all times while the gyrocompass is powered-on.
DPN 060070 © TSS (International) Ltd Issue 3.11 Section 2 Page 13 of 18
Meridian Gyrocompass
2.5 INSTALLATION DRAWINGSFigure 2–5: Gyrocompass installation – Sheet 1
30 330340
170
110
160
SE130
140
120
150
7090
8010
0E
NE60
40
50
250
230
190180 200S 210 220
SW 240
N
NW
320
27 0260
W280
300290
310
20 10 0 350
24VDC Fuse3.15AF
CAUTIONBefore removing the cover or the RCU
unit, remove the gland plate anddisconnect the RCU cable (TB1/17-22)
from the distribution board.
Section 2 Page 14 of 18Issue 3.11 © TSS (International) Ltd DPN 060070
Installation
Figure 2–6: Gyrocompass installation – Sheet 2
30 330340
170
110
160
SE130 140
120
1 5 0
7090
8010
0E
NE60
40
50
250
230
190180 200S
210 220SW 24 0
N
NW
320
27 0260
W280
300290
310
20 10 0 350
24VDC Fuse3.15AF
CAUTIONBefore removing the cover or theRCU
unit, remove the gland plate anddisconnect the RCU cable (TB1/17-22)
from the distribution board.
DPN 060070 © TSS (International) Ltd Issue 3.11 Section 2 Page 15 of 18
Meridian Gyrocompass
Figure 2–7: RCU installation – Table mount
Section 2 Page 16 of 18Issue 3.11 © TSS (International) Ltd DPN 060070
Installation
Figure 2–8: RCU installation – Flush mount
DPN 060070 © TSS (International) Ltd Issue 3.11 Section 2 Page 17 of 18
Meridian Gyrocompass
Section 2 Page 18 of 18Issue 3.11 © TSS (International) Ltd DPN 060070
Operation
3 OPERATING INSTRUCTIONSThis section explains how to power-on and configure the Meridian Gyrocompass after installation. Refer to Section 4 for an explanation of the data formats relevant to the System.
3.1 Control Features Page 2The RCU provides all the controls you will need to operate the Meridian Gyrocompass. It also includes a four-character display panel that shows the heading indication, any alarm messages and error codes.
3.2 Initial Power-on Page 3Explains how to power-on the Meridian Gyrocompass after installation and describes the initialisation sequence.
3.3 Operating Procedure Page 4Explains how to select the latitude and speed correction sources, and how to set the latitude and speed manually if necessary.
3.4 Error Modes Page 6Identifies the system error modes. Use these indicators to identify a possible fault condition.
3.5 Operating Considerations Page 9Includes general advice for operating the Meridian Gyrocompass on a vessel and on high speed craft.
DPN 060070 © TSS (International) Ltd Issue 3.11 Section 3 Page 1 of 12
Meridian Gyrocompass
3.1 CONTROL FEATURESFigure 3–1: RCU front panel features
The RCU front panel includes all the operator controls for the Meridian Gyrocompass:Table 3–1: RCU Control and Indicator functions
Control Function
Power switch. Recessed to prevent accidental operation.
Selection Up. Press to increase display brightness.
Selection Down. Press to decrease display brightness
Latitude. Press to display current Latitude source and correction value. Use in conjunction with the Selection Up and Selection Down buttons to pre-set Latitude source and correction value.
Speed. Press to display current Speed source and correction value. Use in conjunction with the Selection Up and Selection Down buttons to pre-set Speed source and correction value.
Alarm. Press to silence the audible alarm.
012.3 Four digit alphanumeric display.Note: The display can show additional information by alternating the display contents at 0.5Hz. This is indicated throughout the manual as, for example, L52N + SGPS
Power lamp (red) Indicates that the Meridian Gyrocompass is switched on when 24V DC nominal power is connected.
Ready lamp (green)
Indicates that the Meridian Gyrocompass has settled and a True Heading is available.
Table 3–2: RCU display formats
Format Function
Heading0123.40123.4 + DG0123.4 + DG_L
Heading OnlyHeading with DG mode set at the RCUHeading with DG mode set by latitude greater than 80 deg
Section 3 Page 2 of 12 Issue 3.11 © TSS (International) Ltd DPN 060070
Operation
3.2 INITIAL POWER-ONThe Meridian Gyrocompass starting cycle is fully automatic after power is applied. For correct operation Latitude and Speed correction must be applied.
1. Check that there is a nominal 24V DC electrical supply available to the gyrocompass. The acceptable supply range is 18V to 36V DC.
To ensure continuous operation, the power supply for this unit should have a 200W power rating.
2. To start the Meridian Gyrocompass press the power switch on the RCU.
3. Check that the red ‘Power’ lamp on the RCU illuminates. This lamp indicates only that the Meridian Gyrocompass is receiving power and does NOT indicate a settled condition. The instrument illumination will be at maximum during the initialisation sequence. Even at its maximum setting, the instrument illumination may be difficult to see in bright ambient lighting.
4. The RCU will activate the audible alarm for about 1 second. The display will indicate T.E.S.T. and the ‘Ready’ lamp will be lit for about 10 seconds while the system performs a series of self-tests. After successful completion of the self-tests, the display will show the current Gyrocompass dial heading and the ‘Ready’ lamp will go off until the Gyrocompass has settled.
Initially the indicated heading could be inaccurate by as much as 180°. The indicated heading should not be relied on until the Gyrocompass has settled, indicated by an illuminated ‘Ready’ lamp.
5. Set the source of latitude information by following the instructions in sub-section 3.3.1.
6. Set the source of speed information by following the instructions in sub-section 3.3.2.
Speed (by pressing the Speed button)S_01 + S.MANS_01 + S.GPSS_01 + S.LOGS_01 + P.LOG
Speed value with Manual selected speed sourceSpeed value with GPS selected speed sourceSpeed value with LOG selected speed source (serial data input)Speed value with LOG selected speed source and Pulse Log DIP switch set (pulse input)
Latitude (by pressing the Latitude button)L.52N + L.MAN
L.52S + L.MAN
L.52N + L.GPS
Latitude value in the Northern Hemisphere with Manual selected Latitude sourceLatitude value in the Southern Hemisphere with Manual selected Latitude sourceLatitude value with GPS selected Latitude source
Table 3–2: RCU display formats
Format Function
DPN 060070 © TSS (International) Ltd Issue 3.11 Section 3 Page 3 of 12
Meridian Gyrocompass
7. Use the Selection Up and Selection Down buttons to adjust the RCU illumination level to a comfortable setting.
8. Wait for the gyrocompass to settle. This will occur automatically and will take upwards of 24 minutes depending on initial heading offset and sea conditions. The Meridian Gyrocompass signifies its settled condition by illuminating the green ‘Ready’ lamp.
9. If necessary, you can view the software versions of the main unit and the RCU by pressing both the Selection Up and Selection Down buttons simultaneously. The display will toggle between indications of the main unit software version (with prefix ‘M’) and the RCU software version (with prefix ‘R’). The display will continue to toggle for several seconds after you release the buttons and will then return to the heading indication.
3.3 OPERATING PROCEDUREThe Meridian Gyrocompass will settle automatically after power-on, to provide a true north reference. The system requires only latitude and speed correction, applied manually or from external sources, to perform to the specified accuracy.
Ideally, the Meridian Gyrocompass should accept latitude and speed information from external sources such as a GPS receiver or a speed log, which allow the System to apply corrections automatically.
3.3.1 LATITUDE CORRECTION
1. Press and hold the Latitude selection button.
2. Use the Selection Up and Selection Down buttons to set the local latitude manually. The display will show the latitude in one-degree increments in the range 80°N to 80°S, for example L70N
❐ To select automatic latitude compensation from a GPS receiver, use the Selection Up and Selection Down buttons to scroll beyond 80°N or 80°S until the display shows LGPS.
If there is no valid input available from a GPS receiver, the display will indicate a LGPS alarm after 30 seconds.
3. Release both buttons to set the latitude to the displayed value or to set the gyrocompass to use GPS as the source of automatic latitude correction. The display will indicate the latitude setting and latitude source for several seconds and will then return to the normal heading display.
If you input the operating latitude manually, remember to change the setting when necessary. Note that, in medium latitudes, a 10° error in setting the operating latitude will result in a compass error of approximately 0.5°.
Section 3 Page 4 of 12 Issue 3.11 © TSS (International) Ltd DPN 060070
Operation
3.3.2 SPEED CORRECTION1. Press and hold the Speed selection button.
2. Use the Selection Up and Selection Down buttons to set the speed manually in the range zero to 90 knots.
❐ To select automatic speed compensation from a GPS receiver or a speed log, use the selection up button to scroll beyond 90 knots until the display shows SGPS or SLOG.
If there is no valid input available from a speed log or GPS receiver, the display will indicate a SLOG or SGPS alarm after 30 seconds.
3. Release both buttons to set the speed to the displayed value or to set the gyrocompass to use GPS or a speed log as the source of automatic speed correction. The display will indicate the speed setting and speed source for several seconds and will then return to the normal heading display.
If you input the vessel speed manually, remember to set the average vessel speed and to change the setting when necessary. Return the setting to zero on completion of the voyage. For a vessel steaming in a northerly direction, a 5-knot error in speed setting will generate an error of approximately 0.5°.
3.3.3 DG OPERATING MODE
❐ To select Directional Gyro (DG), use the Selection Up and Selection Down buttons to scroll beyond 80°N or 80°S until the display shows DG.
In this mode you can use the Meridian Gyrocompass as a direction indicating instrument all the way up to the poles. If the gyrocompass has settled on north immediately prior to entering the DG mode, it will continue to provide a useful indication of the northerly direction for a period, but will not continue to seek north. The length of time that the direction indication remains valid depends entirely on the gyro drift characteristics.
DG mode will be automatically enabled for latitudes settings greater than 80° applied from the GPS input.The gyrocompass will not north seek while operating in the DG mode.
DPN 060070 © TSS (International) Ltd Issue 3.11 Section 3 Page 5 of 12
Meridian Gyrocompass
3.4 ERROR MODESThe Meridian Gyrocompass has three possible Error modes:
1. Loss or corruption of GPS signal2. Loss or corruption of speed log signal3. Gyrocompass system warnings and failures
3.4.1 LOSS OF GPSThis failure mode can occur when you have selected GPS as the source of speed or latitude information and the signal corrupts or becomes lost for a period of 30 seconds. You can recognise this condition by the following indications:
❐ The display shows S.GPS + FAIL for the loss of speed correction information.
❐ The display shows L.GPS + FAIL for the loss of latitude correction information.
❐ The audible alarm will sound.
Press the Alarm button to cancel the audible alarm.
1. The Gyrocompass will use the last valid speed and latitude values.
2. The RCU will continue to show the alarm message until a valid input signal is re-established or a different input source is selected.
3. If the valid input signal has not been established within a period of 30 minutes the audible alarm will be enabled.
3.4.2 LOSS OF SPEED LOGThis failure mode can occur when you have selected speed log as the source of speed information and the signal corrupts or becomes lost for a period of 30 seconds. You can recognise this condition by the following indications:
❐ The display flashes SLOG + FAIL for the loss of selected serial data source information.
❐ The display flashes PLOG + FAIL for the loss of pulsed selected source information.
❐ The audible alarm will sound.
Press the Alarm button to cancel the alarm.
1. The Gyrocompass will use the last valid speed value.
2. The RCU will continue to show the alarm message until a valid input signal is re-established or a different input source is selected.
If a valid input signal has not been established within a period of 30 minutes the audible alarm will be enabled.
Section 3 Page 6 of 12 Issue 3.11 © TSS (International) Ltd DPN 060070
Operation
3.4.3 GYROCOMPASS SYSTEM WARNINGS AND FAILURESThe Meridian Gyrocompass has a built-in system that monitors operation of the gyrocompass. The functions that this system checks are split into two categories.
❐ Warning conditions
❐ Failure conditions
A failure condition will result in the Gyroscope power supply being disabled. Refer to the maintenance section 5 before activating the Power Supply.
Warning ConditionsIf the gyrocompass detects a warning condition, it will use two methods to alert you:
❐ The display shows <Message> + FAIL
❐ The audible alarm will sound.
Press the Alarm button to cancel the audible alarm.
Table 3–3: Gyrocompass warning codes
The RCU will continue to show the alarm message until the fault condition has been removed. If the fault condition has not been removed within a period of 30 minutes the audible alarm will be enabled. Refer to sub-section 5.1 which outlines some simple checks that you can make to rectify these fault conditions. If necessary contact TSS (International) Ltd or an approved local service agent for assistance.
<Message>RCU Screen Definition of warning code
dc + fail Internal DC power supply is outside operating limits
ac + fail Internal AC power supply is outside operating limits
rdc + fail Loss of internal timing signals
Temp + fail Over or under operating temperature range
rMT + fail Loss of serial communication link with the RCU
DPN 060070 © TSS (International) Ltd Issue 3.11 Section 3 Page 7 of 12
Meridian Gyrocompass
Failure Conditionsf the Meridian Gyrocompass detects a failure condition, it will use six methods to alert you:
❐ The display shows <Message> + FAIL
❐ The audible alarm will sound.
❐ The ‘Ready’ lamp will extinguish.
❐ The Gyro Fail relay will activate.
❐ Serial output will transmit empty sentences.
❐ Stepper output will transmit an illegal code.
Press the Alarm button to cancel the audible alarm.
Table 3–4: Gyrocompass failure codes
This failure is considered to be an unrecoverable fault condition, possibly due to a component failure.
To prevent damage to the Gyroscope the power supplies to it will be disabled.
The Gyrocompass will be disabled until it has been reset by the operator. Refer to the maintenance section 5 before activating the Power Switch.
<Message>RCU Screen Definition of failure code
rot + Fail Rate of Turn exceeds 300o/s
Section 3 Page 8 of 12 Issue 3.11 © TSS (International) Ltd DPN 060070
Operation
3.5 OPERATING CONSIDERATIONS3.5.1 GENERAL OPERATING CONSIDERATIONS❐ You should leave the Meridian Gyrocompass running continuously. Power-off the
system only during long periods of lay-up, for example during vessel dry-docking. To power-off the Meridian Gyrocompass, press the ‘Power’ button. The heading display will go blank and the front panel lamps will switch off. The gyro rotor will take approximately five minutes to come to rest.
❐ If you intend to leave the system powered-off for an extended period, you should arrange to run the gyrocompass for a period of at least thirty minutes at intervals of six months or less.
❐ The Meridian Gyrocompass has full protection against interruption of its electrical supply. It will re-start and align itself automatically on restoration of electrical power. The heading indication will be accurate when the RCU ‘Ready’ lamp is on.
❐ Monitor the Meridian Gyrocompass performance regularly. When functioning correctly, and provided the correct Speed and Latitude compensations are applied, the heading error in latitudes up to 60° and for speeds up to 25 knots will normally be less than 0.75° regardless of the vessel manoeuvres.
❐ Never move the gyrocompass with the gyro rotor spinning unless you leave the servos operational. Note that the gyro rotor continues to spin for a period of approximately five minutes after you power-off the gyrocompass.
DPN 060070 © TSS (International) Ltd Issue 3.11 Section 3 Page 9 of 12
Meridian Gyrocompass
3.5.2 CORRECTIONS FOR SPEED AND LATITUDE❐ Gyrocompass operational accuracy depends, to a large extent, upon accurate
corrections for speed and latitude being applied.
❐ Most users find that the facilities for the automatic application of speed and latitude corrections, via signal inputs from GPS and/or ships log, are a convenient method of applying corrections.
❐ However, users should be aware that if the input signal contains the wrong information, then the wrong corrections will be applied. For instance, it has been noted that some GPS installations, under certain circumstances, will output a “valid” signal with the speed and latitude fields set to all zeros indicating that the vessel is stationary on the equator.
❐ An incorrect input of speed and/or latitude will cause the gyrocompass to indicate an incorrect heading and in the case of extreme errors could cause, in certain circumstances, the gyrocompass to come out of the “Ready mode”.
3.5.3 OPERATING AT EXTREMES OF LATITUDES❐ As latitude increases (north or south) the magnitude of the horizontal component
of the Earth’s rotation rate reduces in proportion to the cosine of latitude. Consequently, the effectiveness of the gyrocompasses north seeking action reduces with increasing latitude.
❐ At latitudes greater than 80o it is recommended that the gyrocompass be operated in the DG (Directional Gyro) mode.
❐ If correction for the effect of latitude on the vertical component of Earth’s rotation is made manually via the RCU, then correction is available to 80o. Thereafter, the directional gyro mode should be manually selected. Errors in the indicated heading will increase with time and increasing latitude above 80o to a maximum of approximately 0.25o /hour. To re-align the gyrocompass, operating latitude must be reduced below 80o and the gyrocompass mode of operation re-selected.
❐ If correction for the effect of latitude on the vertical component of Earth’s rotation is made automatically via a serial data input, then correction is available above 80o and directional gyro mode is automatically selected above this latitude. The compass will still be subject to small inherent drifts while operating in this mode. Reversion to the gyrocompass mode will be made automatically when the serial data latitude input falls below 80o.
3.5.4 OPERATING CONSIDERATIONS FOR VESSEL DYNAMICS
❐ The gyrocompass gravity control gives rise to errors whenever the gyrocompass accelerates or decelerates along the north-south line, that is whenever the northerly speed or course changes. These errors are caused by the inertia of the pendulous element of the gyro, which produces a torque about the horizontal axis and therefore a precession in azimuth. This effect, called ballistic deflection, causes an increase in error during acceleration.
❐ The precession in tilt that arises from the damping component of gravity control is called ballistic tilt. The combined effects of ballistic tilt and ballistic deflection cause the gyrocompass to tilt downwards. Because of the factors that guide the behaviour of a damped gyroscope, the gyro spin axis will return to the settled position by the normal anticlockwise spiral after the acceleration has ceased.
Section 3 Page 10 of 12 Issue 3.11 © TSS (International) Ltd DPN 060070
Operation
❐ In the Meridian Gyrocompass, gravity control comes from an accelerometer (pendulum), which generates an electrical signal related to the tilt of the gyro spin axis. This devices has two important design features; it is heavily damped and the range of output is restricted to a small angle.
The use of accelerometer damping by the Meridian Gyrocompass is of prime importance in the reduction of a particularly serious form of ballistic error called inter cardinal rolling error. This type of error occurs most noticeably when the vessel steams on an inter cardinal heading while rolling simultaneously through a significant angle.
If the gyrocompass is installed at some distance above the vessel centre of roll rotation, as is usually the case on commercial vessels, the resulting lateral acceleration components along the east-west and north-south axes of the gyrocompass combine to build an error in the northerly settle point.
If the effect persists for long enough, this error might become as large as several degrees. However, by damping the accelerometer using a time constant several times larger than the vessel rolling period, inter cardinal rolling errors are significantly reduced.
❐ Another form of ballistic error arises from north-south accelerations generated by vessel manoeuvres. Such accelerations can arise from changes in speed and/or course. By limiting the angular output of the accelerometer, the Meridian Gyrocompass reduces the error potential typically to less than one degree.
❐ It is also possible to eliminate acceleration effects by temporarily operating the compass in the DG (Directional Gyro) mode. In this mode gravity control is used for tilt corrections only, so that ballistic effects would cause negligible heading error during short-term acceleration periods. The DG mode can be selected manually from the control panel.
❐ If the special gyro control mode for HSC is selected, the DG mode will be applied automatically in conditions of high accelerations.
This mode of control is recommended for High Speed Craft and other vessels which may be subjected to high accelerations induced by rapid changes of speed or heading.Under these conditions, operation in the standard control mode can cause automatic reversion to the settle mode and consequently larger dynamic heading errors.
❐ The Meridian Gyrocompass complies with all requirements of IMO Resolution A.821(19), Performance Standards for Gyrocompasses for High-Speed Craft.
❐ On earlier versions of the gyrocompass distribution board, the earth connections displayed on Figure 2.3 Gyro Distribution board may not be present for High Speed Craft (HSC).
DPN 060070 © TSS (International) Ltd Issue 3.11 Section 3 Page 11 of 12
Meridian Gyrocompass
Section 3 Page 12 of 12 Issue 3.11 © TSS (International) Ltd DPN 060070
Technical Data
4 TECHNICAL DATA4.1 SPECIFICATIONS
CAUTIONYou will void the warranty if you operate the gyrocompass outside the environmental conditions detailed in Section 4 and in BS EN 60945.
4.1.1 POWER REQUIREMENTSVoltage 24V DC (acceptable range 18V to 36V DC)
Power consumption 3A at power on, 1.2A continuous (The power supply capacity should exceed 200W)
CAUTIONThe Meridian Gyrocompass should be supplied with power from an SELV source as defined in IEC/EN 60950. The power supply source should be switched and protected by a suitable circuit breaker.
To comply with the requirements of IMO Resolution A.821(19), Performance Standards for Gyrocompasses for High Speed Craft, power to the gyrocompass should be delivered by an uninterruptable power supply.
4.1.2 PERFORMANCE (DEFINITIONS AS IN ISO 8728)Settle point error 0.35° sec latitude
Static error 0.1° sec latitude RMS
Dynamic accuracy 0.3° sec latitude (Scorsby andIntercardinal motion tests)
Settle point repeatability 0.25° sec latitude
Follow up speed 200°/s
Time to settle within 0.7° Less than 45 minutes with a ±30° initial heading offset
4.1.3 COMPENSATIONLatitude compensation range 80°N to 80°S
Speed compensation range 0 to 90 knots
4.1.4 ENVIRONMENTOperating environment EN 60945:1997 designated category
‘weather protected’
Operating temperature 0°C to +45°C (to ISO 8728)–15°C to +55°C (with reduced accuracy)
Storage temperature –25°C to +80°C
DPN 060070 © TSS (International) Ltd Issue 3.11 Section 4 Page 1 of 18
Meridian Gyrocompass
4.1.5 SIGNAL INPUTSLatitude IEC 61162 message string via RS232 or
RS422 from GPS
Speed Pulse or contact closure at 100, 200 or 400 per nautical mile from speed log.
IEC 61162 message string at 4800 baud via RS232 or RS422 from GPS or speed log
4.1.6 SIGNAL OUTPUTSS-type heading 1 × step-by-step, 6 steps per degree (TTL
level) update limited to 20o/s to prevent repeater misalignment
Synchro heading 1 × 26V 400Hz (11.8V maximum line-to-line),sector value 360°
Resolver heading 1 × 36V 400Hz (8V maximum per phase),sector value 360°
Analogue rate of turn 1 × rate of turn ±60°/min (±10V) or ±20°/s (±10V)
Serial data outputs 6 × RS23211 × RS422
Serial data formats IEC 61162 updated at 1Hz , 10Hz or 50Hz. Course recorder output (heading, date, time)
Status/alarm 5V TTL power/gyro failureVoltage free power/gyro failure contacts5V TTL system readyVoltage free system ready contacts
4.1.7 DIMENSIONS AND WEIGHTDimensions 344mm (H) × 267mm (W) × 440mm (D)
Weight 15.5kg
RCU size (when mounted externally) 96mm (H) × 192mm (W) × 108mm (D)
RCU weight 0.75 kg
Disposal
WARNINGDo not dispose of by fire or compacting, as toxic fumes, dust or liquids may be released.
❐ Units contain electrical and electronic components which should be disposed of in accordance with current waste disposal practices.
Units may be returned to the manufacturer for safe disposal.
Section 4 Page 2 of 18 © TSS (International) Ltd Issue 3.11 DPN 060070
Technical Data
4.1.8 LISTENER LOAD REQUIREMENTThe gyrocompass presents a listener load of 1.6mA typical at 2V or 3.5mA typical at 5V to all serial data input signals.
Figure 4–1: Listener input circuit
4.1.9 TALKER DRIVE CAPABILITYThe gyrocompass has a talker drive capability of 150mA to ground.
Derived from 26C31 line drivers.
4.1.10 STANDARDSThe Meridian Gyrocompass is designed to meet the requirements of the following:
❐ IMO Resolution A.424 (XI), Performance Standards for Gyrocompasses❐ IMO Resolution A.821 (19), Performance Standards for Gyrocompasses for High
Speed Craft❐ ISO 16328:2001, Gyrocompasses for High Speed Craft❐ BS EN 60945 (2002), General Requirements - Methods of testing and required
test results❐ BS EN ISO 8728:1999, Shipbuilding – Marine Gyrocompasses❐ BS 6217:1981, Graphical Symbols for use on Electrical Equipment❐ CE marking❐ Electromagnetic Compatibility (EMC) Directive❐ The Marine Equipment Directive 96/98/EC
❐ IEC 61162-1:2000(E) Maritime navigation and radio communication equipment and systems - Digital interfaces. Note that IEC 61162-1:2000(E) is closely aligned with NMEA 0183 version 2.30
❐ USCG, United States Coast Guard Type Approval
DPN 060070 © TSS (International) Ltd Issue 3.11 Section 4 Page 3 of 18
Meridian Gyrocompass
4.2 DATA FORMATS
Set the DIP switches according to your specific input and output requirements. You will find the instructions to do this in sub-section 2.2.4.
Inputs – Refer to sub-section 4.2.2Acceptable input formats:❐ Latitude information using serial IEC 61162 GNS, RMC, GLL or GGA sentences. If
more than one of these formats is available, the Meridian Gyrocompass makes its selection in the stated preference order. Refer to Figures 4–3, 4–4, 4–5 and 4–6 respectively for a description of these formats.
❐ Datum reference using IEC 61162 DTM sentence. The latitude offset is not used to correct the gyroscope latitude information, however the DTM sentence is re-transmitted.
❐ Speed information using serial IEC 61162 VBW, RMC, VTG or VHW sentences. The sentences can contain speed information using knots and/or km/h. The Meridian Gyrocompass will use the speed in knots if available, in preference to speed in km/h. If more than one of these formats is available, the Meridian Gyrocompass makes its selection in the stated preference order. Refer to Figures 4–8, 4–4, 4–9 and 4–10 respectively for a description of these formats.
❐ If an RMC sentence is used it must contain both speed and latitude information.
❐ TTL-compatible pulsed speed input with a TTL-level signal or contact closure.
Outputs – Refer to sub-section 4.2.3Serial output formats:The Meridian Gyrocompass transmits selected information through RS232 and RS422 serial lines using the IEC 61162 format. The serial transmission can be at either 4800, 9600 or 38400 baud, with updates occurring at 1Hz, 10Hz or 50Hz as defined by the setting of the DIP switches.
Other output formats:
❐ Synchro Heading Output
❐ Resolver Heading Output
❐ Stepper S-code Heading Output
❐ Rate of turn using a bipolar analogue voltage in the range ±10V
The following sub-sections describe each of the formats supported by the Meridian Gyrocompass .
Section 4 Page 4 of 18 © TSS (International) Ltd Issue 3.11 DPN 060070
Technical Data
4.2.1 IEC 61162 SERIAL DATA FORMATS – GENERAL INFORMATIONThe Meridian Gyrocompass accepts and transmits asynchronous serial data using 8 data bits, one stop bit and no parity through RS232 and RS422 transmit-only lines. The data bits occur in each packet with the least significant bit first. The most significant bit of the 8-bit character will always be zero.
Figure 4–2: Serial data format
All data is interpreted as ASCII characters that form IEC 61162 sentences split into individual fields. All fields, including null fields, are separated by commas.
The IEC 61162 format requires a checksum – if included, the checksum occurs as an additional field immediately before the carriage return line-feed characters. It consists of an asterisk (*) followed by a checksum derived by exclusive OR-ing the eight data bits of each valid character preceding the asterisk, but excluding the $ symbol, in the sentence. The absolute value of the checksum is transmitted in ASCII characters representing the value in HEX. For circumstances where the Meridian Gyrocompass retransmits serial data using the same IEC 61162 sentence format supplied by an external source, it will recalculate any checksum and insert the new value into the output sentence.
IEC 61162 sentences are usually transmitted once per second, however you can set a DIP switch to select a transmission update rate of either 1, 10 or 50 per second. The outputs are grouped into two channels that can be set independently. The All Data output option of heading, latitude, speed, datum, rate of turn and time sentences will always be transmitted at 1Hz.
DPN 060070 © TSS (International) Ltd Issue 3.11 Section 4 Page 5 of 18
Meridian Gyrocompass
4.2.2 INPUTS4.2.2.1 IEC 61162 INPUT SIGNALS
The Meridian Gyrocompass will accept sentences in both the IEC 61162-1:2000(E) and NMEA 0183 version 2.1 data formats.
In the following descriptions of input sentences, the Meridian Gyrocompass uses the data fields marked ‘XXX’ in the IEC 61162 sentence. The system does not use the fields marked ‘???’ and their descriptions are included here for completeness only. The gyrocompass will recognise the arriving sentence format and will extract the required data from it automatically.
GPS Interface (see Table 2-3 for connection details)The Meridian Gyrocompass can accept speed, latitude, date and time inputs at the GPS interface in IEC 61162 format using GNS, RMC, GLL, GGA, VTG, VHW and ZDA sentences.
Figure 4–3: IEC 61162 GNS input sentence structure
Figure 4–4: IEC 61162 RMC input sentence structure
$??GNS,??????.??,XXXX.XX,X,?????.??,?,X--X,??,?.?,?.?, [CRLF]?.?,?.?,?.?*??
Talk
erid
entif
ier
(any
char
acte
rs)
Mne
mon
icfo
rG
NS
Sfix
data
UT
Cof
posi
tion
Nor
th/S
outh
Latit
ude
(ddm
m.m
m)
Long
titud
e
Car
riage
retu
rnLi
ne-f
eed
char
acte
rs
Sta
rtch
arac
ter
Eas
t/Wes
t
Diff
eren
tial r
efer
ence
stat
ion
ID
Che
cksu
mfie
ld
Age
ofdi
ffere
ntia
l dat
a
Geo
idal
sepe
ratio
n,m
Ant
enna
altit
ude,
m, r
e:m
ean-
sea-
leve
l (ge
oid)
HD
OP
Tota
l num
ber
ofsa
telli
tes
inus
e,0-
99
Mod
eIn
dica
tor
$??RMC,??????.??,X,XXXX.XX,X,?????.??,?,X.X,?.?,??????,?.?,?,X[CRLF]
Talk
erid
entif
ier
(any
char
acte
rs)
Mne
mon
icfo
rR
ecom
men
ded
Min
GP
Sda
ta
UT
Cof
posi
tion
(hhm
mss
.ss)
Latit
ude
(ddm
m.m
m
Mne
mon
icfo
rN
orth
orS
outh
Sta
tus,
A=
valid
, V=
Nav
. Rec
eive
rw
arni
ng
Long
itude
(ddd
mm
.mm
)
Mne
mon
icfo
rE
ast o
rW
est
Mag
netic
varia
tion
indi
cato
rea
stor
Wes
t
Gro
und
spee
din
knot
s
Mag
netic
varia
tion
inde
gree
s
Cou
rse
over
grou
ndin
degr
ees
Dat
eof
fix
Car
riage
retu
rnLi
ne-f
eed
char
acte
rs
Sta
rtch
arac
ter
Mod
eIn
dica
tor
Section 4 Page 6 of 18 © TSS (International) Ltd Issue 3.11 DPN 060070
Technical Data
Figure 4–5: IEC 61162 GLL input sentence structure
Figure 4–6: IEC 61162 GGA input sentence structure
Figure 4–7: IEC 61162 DTM input sentence structure
$??GLL,XXXX.XX,X,?????.??,?,??????.??,X,X[CRLF]
Talk
erid
entif
ier
(any
char
acte
rs)
Mne
mon
icfo
rge
ogra
phic
alLa
t and
Lon
Latit
ude
(ddm
m.m
m)
Long
itude
(ddd
mm
.mm
)
Mne
mon
icfo
rN
orth
orS
outh
Mne
mon
icfo
rE
ast o
rW
est
Car
riage
retu
rnLi
ne-f
eed
char
acte
rs
Sta
rtch
arac
ter
UT
Cof
posi
tion
(hhm
mss
.ss)
Sta
tus
Mod
eIn
dica
tor
$??GGA,??????.??,XXXX.XX,X,?????.??,?,X,??,?.?,?.?,?,?.?,?,?.?,????[CRLF]
Talk
erid
entif
ier
(any
char
acte
rs)
Mne
mon
icfo
rG
PS
fixda
ta
UT
Cof
posi
tion
(hhm
mss
.ss)
Latit
ude
(ddm
m.m
m
Mne
mon
icfo
rN
orth
orS
outh
Long
itude
(ddd
mm
.mm
)
Mne
mon
icfo
rE
ast o
rW
est
GP
Squ
ality
indi
cato
r
Num
ber
ofsa
telli
tes
inus
e(0
0-
12)
Hor
izon
tal d
ilutio
nof
prec
isio
n
Ant
enna
altit
ude
rela
tive
tom
ean
sea
leve
l
Mne
mon
icfo
rm
etre
s
Mne
mon
icfo
rm
etre
s
Geo
idal
sepa
ratio
n
Age
ofdi
ffere
ntia
l GP
Sda
ta
Diff
eren
tial r
efer
ence
stat
ion
(000
0-
1023
)
Car
riage
retu
rnLi
ne-f
eed
char
acte
rs
Sta
rtch
arac
ter
$??DTM,???,?,?.?,?,?.?,?,?.?,???*hh[CRLF]
Talk
erid
entif
ier
Mne
mon
icfo
rD
atum
refe
renc
e
Loca
l dat
umsu
bdiv
isio
nco
de
Latit
ude
offs
et
Loca
l dat
um
Ref
eren
ceda
tum
Nor
th/S
outh
Che
cksu
mfie
ld
Car
riage
retu
rnLi
ne-f
eed
char
acte
rs
Sta
rtch
arac
ter
Long
itude
offs
et
Eas
t/Wes
t
Alti
tude
offs
et, m
DPN 060070 © TSS (International) Ltd Issue 3.11 Section 4 Page 7 of 18
Meridian Gyrocompass
Figure 4–8: IEC 61162 VBW input sentence structure
Figure 4–9: IEC 61162 VTG input sentence structure
Figure 4–10: IEC 61162 VHW input sentence structure
$??VBW,?.?,?.?,?,X.X,?.?,X,?.?,?,?.?,?*hh[CRLF]Ta
lker
iden
tifie
r(a
nych
arac
ters
)
Mne
mon
icfo
rD
ual g
roun
d/w
ater
spee
d
Long
itudi
nal w
ater
spee
d,kn
ots
Sta
tus:
wat
ersp
eed,
A=
valid
, V=
not v
alid
Tra
nsve
rse
wat
ersp
eed,
knot
s
Long
itudi
nal g
roun
dsp
eed,
knot
s
Car
riage
retu
rnLi
ne-f
eed
char
acte
rs
Sta
rtch
arac
ter
Tra
nsve
rse
grou
ndsp
eed,
knot
s
Sta
tus:
ster
ngr
ound
spee
d,A
=va
lid, V
=no
t val
id
Che
cksu
mfie
ld
Sta
tus:
grou
ndsp
eed,
A=
valid
, V=
not v
alid
Ste
rntr
ansv
erse
wat
ersp
eed,
knot
s
Sta
tus:
ster
nw
ater
spee
d,A
=va
lid, V
=no
t val
id
Ste
rntr
ansv
erse
grou
ndsp
eed,
knot
s
$??VTG,?.?,?,?.?,?,X.X,X,XX.X,X,X[CRLF]
Talk
erid
entif
ier
(any
char
acte
rs)
Mne
mon
icfo
rgr
ound
cour
sean
dsp
eed
Mne
mon
icfo
rT
rue
head
ing
Mne
mon
icfo
rM
agne
tiche
adin
g
Cou
rse
inde
gree
san
dte
nths
Mne
mon
icfo
rkn
ots
Spe
edin
knot
s
Spe
edin
km/h
Mne
mon
icfo
rkm
/h
Car
riage
retu
rnLi
ne-f
eed
char
acte
rs
Sta
rtch
arac
ter
Cou
rse
inde
gree
san
dte
nths
Mod
ein
dica
tor
Section 4 Page 8 of 18 © TSS (International) Ltd Issue 3.11 DPN 060070
Technical Data
Figure 4–11: IEC 61162 ZDA input sentence structure
Log Interface (see Table 2-3 for connection details)The Meridian Gyrocompass can accept speed inputs at the Log interface in IEC 61162 format using VBW, VTG and VHW sentences only.
Figure 4–12: IEC 61162 VBW input sentence structure
Figure 4–13: IEC 61162 VTG input sentence structure
$??ZDA,XXXXXX.XX,XX,XX,XXXX,??,??[CRLF]Ta
lker
iden
tifie
r(a
nych
arac
ters
)
Mne
mon
icfo
rT
ime
and
Dat
e
Day
ofm
onth
(01
to31
)
Mon
thof
year
(01
to12
)
UT
C(h
hmm
ss.s
s)
Loca
l zon
eho
urs
(00
to±
13)
Yea
r
Loca
l zon
em
inut
es(0
0to
+59
)
Car
riage
retu
rnLi
ne-f
eed
char
acte
rs
Sta
rtch
arac
ter
$??VBW,?.?,?.?,?,X.X,?.?,X,?.?,?,?.?,?*hh[CRLF]
Talk
erid
entif
ier
(any
char
acte
rs)
Mne
mon
icfo
rD
ual g
roun
d/w
ater
spee
d
Long
itudi
nal w
ater
spee
d,kn
ots
Sta
tus:
wat
ersp
eed,
A=
valid
, V=
not v
alid
Tra
nsve
rse
wat
ersp
eed,
knot
s
Long
itudi
nal g
roun
dsp
eed,
knot
s
Car
riage
retu
rnLi
ne-f
eed
char
acte
rs
Sta
rtch
arac
ter
Tra
nsve
rse
grou
ndsp
eed,
knot
s
Sta
tus:
ster
ngr
ound
spee
d,A
=va
lid, V
=no
t val
id
Che
cksu
mfie
ld
Sta
tus:
grou
ndsp
eed,
A=
valid
, V=
not v
alid
Ste
rntr
ansv
erse
wat
ersp
eed,
knot
s
Sta
tus:
ster
nw
ater
spee
d,A
=va
lid, V
=no
t val
id
Ste
rntr
ansv
erse
grou
ndsp
eed,
knot
s
$??VTG,?.?,?,?.?,?,X.X,X,XX.X,X,X[CRLF]
Talk
erid
entif
ier
(any
char
acte
rs)
Mne
mon
icfo
rgr
ound
cour
sean
dsp
eed
Mne
mon
icfo
rT
rue
head
ing
Mne
mon
icfo
rM
agne
tiche
adin
g
Cou
rse
inde
gree
san
dte
nths
Mne
mon
icfo
rkn
ots
Spe
edin
knot
s
Spe
edin
km/h
Mne
mon
icfo
rkm
/h
Car
riage
retu
rnLi
ne-f
eed
char
acte
rs
Sta
rtch
arac
ter
Cou
rse
inde
gree
san
dte
nths
Mod
ein
dica
tor
DPN 060070 © TSS (International) Ltd Issue 3.11 Section 4 Page 9 of 18
Meridian Gyrocompass
Figure 4–14: IEC 61162 VHW input sentence structure
4.2.2.2 PULSED INPUT
The Meridian Gyrocompass can accept a speed input as a series of pulses or contact closures occurring at a frequency of 100, 200 or 400 per nautical mile as selected by a DIP switch. Refer to Table 2-5. The gyrocompass determines the vessel speed by reference against the microprocessor timing circuits. The speed pulses do not need to have a particular mark/space ratio, although they should be TTL-level. Contact closures should be of good quality and electrically floating.
Section 4 Page 10 of 18 © TSS (International) Ltd Issue 3.11 DPN 060070
Technical Data
4.2.3 OUTPUTS4.2.3.1 IEC 61162 OUTPUT SIGNALS
The Meridian Gyrocompass can output serial data through RS232 and RS422 transmit-only serial lines using the IEC 61162-1:2000(E) format. The output of each channel can be set independently, using DIP switches, to contain either:
1. Heading - as described below, OR
2. Heading and Rate of turn - as described below, OR
3. Rate of turn only - as described below, OR
4. All data - all information described below, transmitted in the order stated
❐ Heading information is transmitted using an HDT format sentence. The resolution of the heading information can be set to one or two decimal places at the DIP switches. Refer to Figures 4–15 for a description of this output format.
❐ Rate of turn information is transmitted using a ROT format sentence. Refer to Figure 4–16 for a description of this output format.
❐ Speed information is transmitted using a VTG format sentence if the gyrocompass is configured for manual or a pulsed speed log input. The VTG sentence also has provision for Heading and this is inserted at a resolution as set by the DIP switches. Refer to Figure 4–18 for a description of this output format. If the gyrocompass is configured for a GPS speed input and the speed information arrives at the gyrocompass in either VBW, RMC, VTG or VHW format, then the gyrocompass will retransmit the received format modifying the sentence to include the HE talker identifier. Refer to Figures 4–17, 4–21, 4–18, and 4–19 for a description of these output formats.
❐ Datum reference is retransmitted if the DTM sentence is received on the GPS input. The gyrocompass will re-transmit the received sentence modifying it to include the HE talker identifier. Refer to Figure 4–24 for a description of this output format.
❐ Latitude information is transmitted using a GLL format sentence if the gyrocompass is configured for manual latitude input. Refer to Figure 4–22 for a description of this output format. If the gyrocompass is configured for a GPS latitude input and the latitude information arrives at the gyrocompass in either GNS, RMC, GLL, or GGA format, then the gyrocompass will retransmit the received sentence modifying the sentence to include the HE talker identifier. Refer to Figures 4–20, 4–21, 4–22 and 4–23 for a description of these output formats.
❐ Date and time information is transmitted using a ZDA format sentence. The gyrocompass will transmit the ZDA sentence including the HE talker identifier. If this information is received from a GPS source, all fields will be retransmitted. If there is no valid date and time from an external source, the gyrocompass will transmit the ZDA sentence with empty data fields. Refer to Figure 4–25 for a description of this output format.
If the All Data output format is selected at the DIP switches, the transmission update rate for that channel will be at 1Hz regardless of the setting of the channel update rate.The All Data output is not suitable for HSC applications.
DPN 060070 © TSS (International) Ltd Issue 3.11 Section 4 Page 11 of 18
Meridian Gyrocompass
In the following descriptions of output sentences, the gyrocompass sets the contents of fields marked XXX and leaves unchanged the fields marked ???
Figure 4–15: IEC 61162 HDT output sentence structure
Figure 4–16: IEC 61162 ROT output sentence structure
Figure 4–17: IEC 61162 VBW output sentence structure$HEVBW,?.?,?.?,?,?.?,?.?,?,?.?,?,?.?,?*hh[CRLF]
Talk
erid
entif
ier
(any
char
acte
rs)
Mne
mon
icfo
rD
ual g
roun
d/w
ater
spee
d
Long
itudi
nal w
ater
spee
d,kn
ots
Sta
tus:
wat
ersp
eed,
A=
valid
, V=
not v
alid
Tra
nsve
rse
wat
ersp
eed,
knot
s
Long
itudi
nal g
roun
dsp
eed,
knot
s
Car
riage
retu
rnLi
ne-f
eed
char
acte
rs
Sta
rtch
arac
ter
Tra
nsve
rse
grou
ndsp
eed,
knot
s
Sta
tus:
ster
ngr
ound
spee
d,A
=va
lid, V
=no
t val
id
Che
cksu
mfie
ld
Sta
tus:
grou
ndsp
eed,
A=
valid
, V=
not v
alid
Ste
rntr
ansv
erse
wat
ersp
eed,
knot
s
Sta
tus:
ster
nw
ater
spee
d,A
=va
lid, V
=no
t val
id
Ste
rntr
ansv
erse
grou
ndsp
eed,
knot
s
Section 4 Page 12 of 18 © TSS (International) Ltd Issue 3.11 DPN 060070
Technical Data
Figure 4–18: IEC 61162 VTG output sentence structure
In GPS mode, only the talker identifier is changedIn manual mode, the magnetic course fields are empty.
Figure 4–19: IEC 61162 VHW output sentence structure
Figure 4–20: IEC 61162 GNS output sentence structure
$HEVHW,???.?,?,???.?,?,??.?,?,??.?,?[CRLF]
Talk
erid
entif
ier
(any
char
acte
rs)
Mne
mon
icfo
rve
ctor
head
ing
and
wat
ersp
eed
Mne
mon
icfo
rT
rue
head
ing
Mne
mon
icfo
rM
agne
tiche
adin
g
Hea
ding
inde
gree
san
dte
nths
Mne
mon
icfo
rkn
ots
Spe
edin
knot
s
Spe
edin
km/h
Mne
mon
icfo
rkm
/h
Car
riage
retu
rnLi
ne-f
eed
char
acte
rs
Sta
rtch
arac
ter
Hea
ding
inde
gree
san
dte
nths
$HEGNS,??????.??,????.??,?,?????.??,?,????,??,?.?,?.?, [CRLF]?.?,?.?,?.?*??
Talk
erid
entif
ier
(any
char
acte
rs)
Mne
mon
icfo
rG
NS
Sfix
data
UT
Cof
posi
tion
Nor
th/S
outh
Latit
ude
(ddm
m.m
m)
Long
titud
e
Car
riage
retu
rnLi
ne-f
eed
char
acte
rs
Sta
rtch
arac
ter
Eas
t/Wes
t
Diff
eren
tial r
efer
ence
stat
ion
ID
Che
cksu
mfie
ld
Age
ofdi
ffere
ntia
l dat
a
Geo
idal
sepe
ratio
n,m
Ant
enna
altit
ude,
m, r
e:m
ean-
sea-
leve
l (ge
oid)
HD
OP
Tota
l num
ber
ofsa
telli
tes
inus
e,0-
99
Mod
eIn
dica
tor
DPN 060070 © TSS (International) Ltd Issue 3.11 Section 4 Page 13 of 18
Meridian Gyrocompass
Figure 4–21: IEC 61162 RMC output sentence structure
Figure 4–22: IEC 61162 GLL output sentence structure
In GPS mode, only the talker identifier is changedIn manual mode, the longitude and UTC fields are empty.
Figure 4–23: IEC 61162 GGA output sentence structure
Section 4 Page 14 of 18 © TSS (International) Ltd Issue 3.11 DPN 060070
Technical Data
Figure 4–24: IEC 61162 DTM output sentence structure
Figure 4–25: IEC 61162 ZDA output sentence structure
4.2.4 IEC 61162 SENTENCE WITH CHECKSUMWhen the checksum is to be sent with any of the above IEC 61162 sentences, it appears as an extra field inserted before the carriage return character as shown by example in Figure 4-25.
Figure 4–26: IEC 61162 sentence with optional checksum
The checksum consists of an asterisk followed by the checksum calculated by exclusive OR-ing the eight data bits of each valid character preceding the asterisk, but excluding the ‘$’ symbol, in the sentence. The Meridian Gyrocompass transmits the absolute value of the checksum in ASCII characters representing the value in HEX.
$HEDTM,???,?,?.?,?,?.?,?,?.?,???*hh[CRLF]Ta
lker
iden
tifie
r
Mne
mon
icfo
rD
atum
refe
renc
e
Loca
l dat
umsu
bdiv
isio
nco
de
Latit
ude
offs
et
Loca
l dat
um
Ref
eren
ceda
tum
Nor
th/S
outh
Che
cksu
mfie
ld
Car
riage
retu
rnLi
ne-f
eed
char
acte
rs
Sta
rtch
arac
ter
Long
itude
offs
et
Eas
t/Wes
t
Alti
tude
offs
et, m
$HEZDA,??????.??,??,??,????,??,??[CRLF]
Talk
erid
entif
ier
Mne
mon
icfo
rT
ime
and
Dat
e
Day
ofm
onth
(01
to31
)
Mon
thof
year
(01
to12
)
UT
C(h
hmm
ss.s
s)
Loca
l zon
eho
urs
(00
to±
13)
Yea
r
Loca
l zon
em
inut
es(0
0to
+59
)
Car
riage
retu
rnLi
ne-f
eed
char
acte
rs
Sta
rtch
arac
ter
DPN 060070 © TSS (International) Ltd Issue 3.11 Section 4 Page 15 of 18
Meridian Gyrocompass
4.2.5 OTHER OUTPUT FORMATS4.2.5.1 COURSE RECORDER OUTPUT
The following ASCII data shall be transmitted on the Course Recorder Output every minute, in a suitable format to be output on an 80 column line printer.
359.99 True Lat 52 N Spd 10 Kts UTC 13:34:01 01/01/2001
❐ Date and time will only be output if a valid ZDA sentence is available on the GPS input.
4.2.5.2 SYNCHRO OUTPUT
The synchro heading output is available continuously at TB2 on the Distribution Board while the gyrocompass is powered-on – refer to Table 2-4 for connector details. The output is at 11.8V maximum line-to-line voltage derived electrically from a 1:1 resolver driven directly by the gyrocompass azimuth gimbal. The synchro reference voltage is a nominal 26V 400Hz supply generated internally.
Electrical loading specification:
❐ Not less than 5k between any two S lines.
❐ Not less than 1k between the two R lines.
4.2.5.3 RESOLVER OUTPUT
The resolver heading output is available continuously at TB2 on the Distribution Board while the gyrocompass is powered-on – refer to Table 2-4 for connection details. The output is at 8V maximum voltage per phase signal from a 1:1 resolver driven directly by the gyrocompass azimuth gimbal. The resolver reference voltage, which is generated internally, can be set nominal 36V 400Hz or 10V 400Hz by jumper JP30 on PCB929066. The factory default setting is 36V 400Hz.
The resolver sine and cosine outputs must be electrically isolated from each other. Contact the TSS (International) Ltd Service Department for technical advice if necessary.
Electrical loading specification:
❐ Not less than 5k between any two S lines.
❐ Not less than 1k between the two R lines.
Table 4–1: Course Recorder Output Sentences
Heading 999.99
Latitude 99
Hemisphere N or S
Speed Kts 99
Time hh:mm:ss
Date dd/mm/yy
Section 4 Page 16 of 18 © TSS (International) Ltd Issue 3.11 DPN 060070
Technical Data
4.2.5.4 STEPPER S-CODE
The stepper S-code output is available continuously at TB2 on the Distribution Board while the gyrocompass is powered-on – refer to Table 2-4 for connection details.
The stepper output is a TTL compatible S-encoded signal with a 10mA sink capacity.
4.2.5.5 RATE OF TURN
The ROT output is calculated by the internal processor updated at 10Hz and made available continuously at TB3 on the Distribution Board while the gyrocompass is powered-on – refer to Table 2-4 for connection details.
The ROT output is a bipolar analogue voltage in the range ±10V to represent rates of turn from –60° to +60° per minute or –20° to +20° per second by DIP-switches. Refer to Table 2-4 . Positive rates of turn are to starboard.
DPN 060070 © TSS (International) Ltd Issue 3.11 Section 4 Page 17 of 18
Meridian Gyrocompass
Section 4 Page 18 of 18 © TSS (International) Ltd Issue 3.11 DPN 060070
Maintenance
5 MAINTENANCEWARNING
There is a danger of serious injury from voltages inside the Meridian Gyrocompass . Do not remove the gyrocompass cover unless you have the necessary skills and experience to perform maintenance work on a system of this nature. Always power-off the system before you remove the cover for maintenance work.Observe all local safety regulations as you work on the equipment. Reconnect the safety grounding straps and refit all safety covers to the equipment before you power-on the system.
CAUTIONPerform maintenance instructions only if you have the skills and experience required, and only when necessary. Inappropriate tampering with the internal controls and components of the gyrocompass can lead to damage or serious performance degradation.NEVER open the gyrocompass cover or make any adjustments inside the gyrocompass unless you are entirely confident in your actions.
There is very little need for user maintenance on the Meridian Gyrocompass and you should never need to remove the covers.
The following sub-sections explain some very basic procedures that you may attempt if you suspect the system has developed a fault. If you are in any doubt, contact TSS (International) Ltd for advice and technical assistance before you begin any maintenance work on the system.
5.1 Built-in Test Equipment Page 1The Meridian Gyrocompass performs a self-test routine during the initialisation sequence and monitors its status continually during normal operation. Any deviation from normal operation appears as an error message, with the cause declared as a message on the four-character display panel. This sub-section explains some very basic tests and adjustments that you may perform on the system.
5.2 Test Connector Page 3There is a 60-way test connector that allows you to measure critical voltages and signals.
5.1 BUILT-IN TEST EQUIPMENTA Test Box (TSS (International) Ltd part number 929220) is available to facilitate connection to the 60-way connector.
In Subsection 3.4.3 there is a list of warning codes and failure codes delivered by the built-in test equipment if it detects a fault in the gyrocompass. In these conditions, the four-character display will show <Message> + FAIL
DPN 060070 © TSS (International) Ltd Issue 3.11 Section 5 Page 1 of 12
Meridian Gyrocompass
If the built in test equipment detects a fault, use the following table to investigate the cause. You can measure the voltages and signals on the pins of the 60-way test connector (refer to Table 5.2 for details of the test connector).
5.1.1 AZIMUTH DRIFT ADJUSTMENTYou may use the following procedure to measure and, if necessary, adjust the azimuth drift:
1. Ensure that the gyrocompass is static and is operating in DG mode with the Speed input set manually to zero and the Latitude set to local latitude. Refer to sub-sections 3.3.1 to set the latitude, 3.3.2 to set the speed and 3.3.3 to set DG mode.
2. Note the initial heading (H1) shown on the RCU display.
3. Wait for one hour and then note the heading (H2) shown on the RCU display.
4. Calculate the azimuth drift rate (H2 – H1) degrees per hour.
5. Use a digital meter set to measure DC volts and monitor the Tilt Bias between pins 30 and 51 of the 60-way test connector (with the positive test lead on pin 30).
Table 5–1: Test Measurements
Failure Code Measure Expected value Signal source
dc+failFailure of DC power supply
DC supply42 (+ve) to 4344 (+ve) to 4317 (+ve) to 1850 (+ve) to 5152 (+ve) to 5145 (+ve) to 18
18V DC to 36V DC+24V DC ±0.5V DC–24V DC ±0.5V DC+5V DC ±0.1V DC+15V DC ±0.2V DC–15V DC ±0.2V DC+5V DC (+0.2V/–0.7V DC)
Ship’s mains/PSUDC/DC PSUDC/DC PSUDC/DC PSUControl Board analogueControl Board analogueControl Board analogue
ac+failFailure of AC power supply
19 to 4320 to 4321 to 4358 to 4357 (+ve) to 18
2.5V AC ±0.125V AC @ 19.2kHz14V AC ±1V @ 480Hz (18V AC ±1.5V at start (1-min))14V AC ±1V @ 480Hz (18V AC ±1.5V at start (1-min))12V AC ±0.2V @ 400Hz+5V DC ±0.2V DC
Control Board analogueControl Board analogueControl Board analogueControl Board analogueControl Board analogue
rdc+FailFailure of synchro-to-digital converter
58 to 4353 (+ve) to 5154 (+ve) to 51
12V AC ±0.2V @ 400Hz(5.4V DC ±0.5V DC) × sin heading(5.4V DC ±0.5V DC) × cos heading
Control Board analogueControl Board analogueControl Board analogue
rMT+failLoss of RCU communication
50 way IDC Cable (Part Number B929157)+ 5V DC Power Supply5 way Cable Loom (Part Number B929161)
ROT+failRate of turn exceed limit
>300o/s Check Gyro connection to the analogue PCB
Temp+failTemperature exceeds operat-ing range
<-20oC>+60oC
Check operating environment and ventilation
Section 5 Page 2 of 12 Issue 3.11 © TSS (International) Ltd DPN 060070
Maintenance
6. Adjust the Tilt Bias potentiometer RV7 by 400mV × drift rate (°/hr). You must turn the potentiometer anticlockwise to compensate for azimuth drift towards higher readings. Figure 2–4 shows the location of the Tilt Bias potentiometer.
7. Repeat steps 2 to 6 above until the calculated drift rate is less than 0.2°/hr.
8. Refer to sub-section 3.3.3 to deselect the DG mode.
5.1.2 AZIMUTH BIAS ADJUSTMENTYou may use the following procedure to eliminate small angles of heading error from the Meridian Gyrocompass . Measure and, if necessary, adjust for azimuth drift as described in sub-section 5.1.1 above before you adjust the azimuth bias.
Take care when you adjust azimuth bias – make only small adjustments each time and then allow the gyrocompass to settle for three hours before you make any further adjustments. Note the original position of the azimuth bias control before you start so that you can restore the starting condition if necessary.
1. Use a digital meter set to measure DC volts and monitor the Azimuth Bias between pins 29 and 51 of the 60-way test connector (with the positive test lead on pin 29).
2. Adjust the Azimuth Bias potentiometer RV9 to cause a change in the azimuth bias voltage that will produce the necessary change in compass heading. Figure 2–4 shows the location of the Azimuth Bias potentiometer.
3. Turn the Azimuth Bias potentiometer anticlockwise to cause the heading to change towards a lower reading. A 60mV DC change in Azimuth Bias will produce a 1-degree change in heading.
5.2 TEST CONNECTORThere is a sixty-way test connector accessible behind the removable panel on the top of the gyrocompass cover. Release and remove the securing screws and lift off the panel to see the two DIP switches and the test connector. A test box (TSS part number 929220) is available to facilitate connection to the 60-way test connector. Table 5–2: Sixty-way Test Connector
Pin Name Function
1 S1_SYNCHRO 11.8V RMS 400Hz synchro S1 phase
2 S2_SYNCHRO_RES 11.8V RMS 400Hz synchro S2 phase
3 S3_SYNCHRO_RES 11.8V RMS 400Hz synchro S3 phase
4 26V_SYNCHRO_R1 26V RMS 400Hz synchro R1 reference
5 0V_SYNCHRO_RES 26V RMS 400Hz synchro R1 reference
6 GA_MODE Directional gyro mode control (+5V logic)
7 GC_MODE Gyrocompass mode control (+5V logic)
8 AA_MODE Auto alignment mode control (+5V logic)
9 LAT_NS Latitude north selection control (+5V logic)
10 SERVO_EN Tilt and azimuth servo enable control (+5V logic)
DPN 060070 © TSS (International) Ltd Issue 3.11 Section 5 Page 3 of 12
Meridian Gyrocompass
11 WHEEL_BOOST Gyro wheel supply boost control (+5V logic)
12 LOG_OK Speed log OK flag (+5V logic)
13 GPS_OK GPS OK flag (+5V logic)
14 SYS_FAIL System fail flag (+5V logic)
15 GYRO_RDY Gyrocompass ready flag (+5V logic)
16 PREPARE Prepare mode (servo nulling) (+5V logic)
17 VCC 5V DC supply
18 GND 5V DC supply return
19 PICK_OFF_SUPPLY_1 Gyro pick off supply 2.5V RMS 19.2kHz sine wave
20 WHEEL_SUPPLY_1 Gyro wheel supply 0 phase 10V (18V) RMS 480Hz square wave
21 WHEEL_SUPPLY_2 Gyro wheel supply 90 phase 10V (18V) RMS 480Hz square wave
22 PWMO Compass card illumination PWM control 5V 85Hz square wave
23 ACC Gravity control signal ±150mV DC/min T=60s
24 10V 10V DC positive voltage reference
25 _10V 10V DC negative voltage reference
26 LAT_TORQ Latitude torquing input signal (–10 sin[latitude])V DC
27 SPEED_N_TORQ Speed N torque i/p signal (7.3e–3 × speed(kts) × cos[heading])
28 SPEED_E_TORQ Speed E torque i/p signal (–8.5e–3 × speed(kts) × sin[heading] × tan[latitude]V DC
29 AZ_BIAS Bias adj. to azimuth torquer ±2.2V DC (60mV/deg heading)
30 TILT_BIAS Bias adj. to tilt torquer ±2.2V DC (400mV/deg/hour heading)
31 TILT_TEMP Bias adj. to tilt torquer proportional to temperature (400mV/deg/hr heading)
32 AZ_TEMP Bias adj. to azimuth torquer proportional to temperature (60mV/deg/hr heading)
33 T Temperature ref (non-inverted) from gimbal thermistor (DC V proportional to temp)
34 T_ Temperature ref (inverted) from gimbal thermistor (DC V proportional to temp)
35 TILT_TORQUER_LO Tilt torquer signal 0.013V DC/mA (torquer scale factor 10°/hr/mA)
36 AZ_TORQUER_LO Azimuth torquer signal 0.006V DC/mA (torquer scale factor 10°/hr/mA)
37 TILT_PICK_OFF_DC Demodulated gyroscope tilt pick-off signal
38 AZ_PICK_OFF_DC Demodulated gyroscope azimuth pick-off signal
39 18V10V Gyro wheel positive supply
40 -18V10V Gyro wheel negative supply
41 UP_DOWN Accelerometer - Slave comparator
42 24V 24V DC positive supply
Table 5–2: Sixty-way Test Connector
Pin Name Function
Section 5 Page 4 of 12 Issue 3.11 © TSS (International) Ltd DPN 060070
Maintenance
43 0V Supply return for ±24V DC
44 –24V 24V DC negative supply
45 PSU_LO PSU (+5V DC and ±15V DC) under voltage flag (+5V DC logic)
46 NOT USED
47 ACC_COS_LAT Latitude weighted gravity control signal (150/cos latitude)mV DC/min
48 SLAVE Slave accelerometer gravity control signal (10mV/bit)
49 ROT Analogue rate of turn output (0.5V DC/deg/s (10V DC max) CW +ve; ACW –ve
50 15V 15V DC positive supply
51 0Va Supply return for ±15V DC
52 –15V 15V DC negative supply
53 SIN_DC Analogue voltage proportional to sin(heading) (±0.1V DC/deg heading)
54 COS_DC Analogue voltage proportional to cos(heading) (±0.1V DC/deg heading)
55 RS232_RX_TEST RS232 receive port reserved for product testing
56 RS232_TX_TEST RS232 transmit port diagnostic output sentence
57 AC_OK AC supply (19kHz, 480Hz and 400Hz) OK flag (+5V DC logic)
58 400_REF_HI Reference supply 12V RMS 400Hz
59 AZ_MOTOR_HI Drive to azimuth follow-up DC servo motor
60 TILT_MOTOR_HI Drive to tilt follow-up DC servo motor
Table 5–2: Sixty-way Test Connector
Pin Name Function
DPN 060070 © TSS (International) Ltd Issue 3.11 Section 5 Page 5 of 12
Meridian Gyrocompass
5.3 DIAGNOSTIC OUTPUT SENTENCEAn ASCII character diagnostic sentence, delivered via RS232 line standard at 4800 baud, is available at test connector PL6/56-18(GND).
Note that this sentence information is only valid for gyrocompasses fitted with software of the following version or higher: BPR 113 (main) and BPR 114 (RCU).
It may be useful to monitor this sentence when communicating with TSS (International) Ltd for technical assistance. The sentence string may be read using "Microsoft Terminal" or similar ASCII reader.
Sentence StructureGyro Control 1 = slave accelerometer (new hardware)
S = special gyro control mode for HSC (for gyrocompasseswith serial numbers later than 3500)R = real accelerometer (original hardware)A = special applications only (original hardware)
Mode L = levelA = alignmentC = compassD = DG
Status F = failR = readyS = settle
Latitude (degrees) xxHemisphere N or SSpeed (knots) xxAverage Accelerometer (bits) Paxxx
ADC 1 (bits) rxxxADC 2 (bits) hxxxADC 3 (bits) txxxADC 4 (bits) axxxADC 5 (bits) Txxx
DAC 1a (bits) xxxDAC 1b (bits) xxxDAC 2a (bits) xxxDAC 2b (bits) xxxDAC 3a (bits) xxxDAC 3b (bits) xxxHeading (degrees) $HEHDT,xxx.xx,T
Sentence ExampleR CR 51N 06 Pa128r128h128 t128a128 T096 160 198 000 000 128 128 $HEHDT,000.00,T
During start-up, the Mode and Status characters will change in the following sequence:
1. LS for about 4 minutes2. AS for 25 - 60 minutes (dependent upon initial heading misalignment)3. CR in READY mode and functioningEnsure that the Latitude and Speed values in the sentence correspond with the automatic or manually set values applied to the gyrocompass. Ensure that the Heading value in the sentence is correct.
Section 5 Page 6 of 12 Issue 3.11 © TSS (International) Ltd DPN 060070
Maintenance
Figure 5–1: System Block Diagram
GIM
BA
LA
SS
Y
DIS
PLA
YB
OA
RD
CO
NT
RO
LB
OA
RD
RE
MO
TE
DIS
TR
IBU
TIO
N
BO
AR
D
CO
NT
RO
LB
OA
RD
DIG
ITA
LA
NA
LO
GU
E
CO
NT
RO
LB
OA
RD
TE
ST
CO
NN
EC
TO
R
DC
/DC
PS
U
FIL
TE
RS
#1

24V
d.c
.
Tilt
Moto
r
Azim
uth
Moto
r
Tilt
Pic
koff
Azim
uth
Pic
koff
Tilt
Torq
uer
Azim
uth
Torq
uer
(vert
icalsensor)
(tem
psensor)
Resolv
er
Illu
min
atio
n24-0
-24V
d.c
.
5V
d.c
.
An
alo
gu
eC
on
tro
lS
ign
als
Azim
uth
To
rqu
er
Co
ntr
olS
ign
al
Tilt
Torq
uer
Contr
olS
ignal
Tem
pS
ensor
Sig
nal
Acce
lero
me
ter
Sig
na
l
Re
so
lve
rH
ea
din
gS
ign
al(s
in/c
os)
Tilt
Pic
koff
Sig
nal(a
.c.)
Azim
uth
Pic
koff
Sig
nal(a
.c.)
Tilt
Moto
rD
rive
Sig
nal
Azim
uth
Mo
tor
Drive
Sig
na
l
Illu
min
atio
nC
on
tro
l
Acce
lero
me
ter
Sig
na
l(h
igh
ga
in)
Tem
pS
ensor
Sig
nal
Re
so
lve
rH
ea
din
gS
ign
al(d
.c.)
Tilt
P.O
.S
ignal(d
.c.)
Azim
uth
P.O
.S
ignal(d
.c.)
Analo
gue
Headin
gS
ignals
SerialO
utp
ut
Sig
nals
Serial&
Dig
italIn
putS
ignals
Rem
ote
ON
/OF
FC
ontr
ol
Gyro
Sp
inM
oto
rS
up
ply
Gyro
Sp
inM
oto
r
Rem
ote
ON
/OF
F
Com
munic
ations
Display Driver Signals
Input
Sig
nals
Outp
ut
Sig
nals
5V
d.c
.
Com
munic
ations
929083
929074
929066
929033
929078
929049
929045
Pow
er
Pow
er
Switch I/Ps
Acce
lero
me
ter
Therm
isto
r
DPN 060070 © TSS (International) Ltd Issue 3.11 Section 5 Page 7 of 12
Meridian Gyrocompass
Figure 5–2: Gimbal Assembly Functional DiagramZ
H
X
Y
N-S
H
Resolv
er
40
0H
zS
inH
Co
sH
Azim
uth
Torq
uer
Co
ntr
olS
ign
al
Sig
na
l(A
cc)
Acce
lero
me
ter
Co
ntr
olS
ign
al
Tilt
Torq
uer
Moto
r
Azim
uth
Dri
ve
Sig
na
l
Tilt
Moto
r
Dri
ve
Sig
na
l
Te
mp
era
ture
Se
nso
rS
ign
al
Azim
uth
Pic
koff
Sig
na
l
Tilt
Pic
ko
ff
Sig
na
l
1
2
8
5
9
67
3
4
10
1.D
am
pe
r
2.G
yro
sp
inm
oto
r
3.
Tilt
torq
uer
4.
Azim
uth
torq
ue
r
5.
Acce
lero
me
ter
6.
Azim
uth
pic
ko
ff
7.
Tilt
pic
koff
8.T
he
rmis
tor
9.
Tilt
moto
r
10
.A
zim
uth
mo
tor
Section 5 Page 8 of 12 Issue 3.11 © TSS (International) Ltd DPN 060070
Maintenance
Figure 5–3: Analogue Control Board Block Diagram
M
TILTTORQUERCOIL
PICKOFFCOILS
TILT
TILTMOTOR
Run
Align
TILT TEMPT+ T-
TILT BIAS+V Ref -V Ref
+/-
Hemisphere
+/-
Servo Enable
SCALING&
SHAPING
AMPLIFIER
FILTER&
AMPLIFIER
SCALING
SHAPING&
FILTER& PICKOFF
AZIMUTH
AZIMUTHMOTOR
COILS
M
COMPARATOR
COILTORQUERAZIMUTH
Align
DG
AZIMUTH TEMPT+ T-
AZIMUTH BIAS+V Ref -V Ref
Run
X10
AlignRun
Hemisphere (+/-)Servo Enable
DG
19.2 Khz Ref
Acc/Cosλ
ACCELEROMETER
THERMISTORAMPLIFIER
THERMISTORT+
T-
To Tilt & Azimuthtemperature pots
PRECISIONREFERENCE
Temperature
+V Ref
-V Ref
DIGITAL CONTROL BOARD ANALOGUE CONTROL BOARD GIMBAL ASSEMBLY
Hemisphere
36V26V
0V
R4R1
R2
ReferencePhase26V Synchro36V Resolver
400HzRESOLVERROTOR
STATORRESOLVER
S1
S311.8V Synchro8V Resolver
Heading Outputs
S2
S4
+/-
+/-
400Hz Ref
400Hz Ref
Wheel Boost
2.5V 19.2KhzPickoff Supply
Gyro Spin MotorSupply
MONO -STABLE
10V/18V 480Hz
V.Sin H.Tan λ R
Acc (High Gain)
Acc (Low Gain) τ = 60s
V.Cos HR
Rate of Turn RoT +/- 10V
10V/18V
10V/18V
∅1
2∅
PLD3.6Mhz
+24V
-24V
400Hz
19.2Khz
BANDPASSFILTER
400Hz Ref
400Hz Ref
BANDPASSFILTER
19.2Khz Ref
Sin H
Cos H
8V.Sin H
8V.Cos H
V = speed (knots x 6080 ft/hr)
λ = local latitude (deg) H = gyro heading (deg) τ = time constant Acc = accelerometer signal
Servo Enable
ω Sin λ
AC OK
+/-
+/-Azimuth Pickoff (d.c.)
Tilt Pickoff (d.c.)
REG+
REG-
480Hz ∅ 0
180∅ 480Hz 90∅ 480Hz
270∅ 480Hz
North seaking
Latitude correction
Easterly speed correction
Northerly speed correction
Damping
ω = earth rotation (15°/hr)
R = earth radius (20.9 x 106 ft)
(temp sensor)
(vertical sensor)
DPN 060070 © TSS (International) Ltd Issue 3.11 Section 5 Page 9 of 12
Meridian Gyrocompass
Figure 5–4: Digital Control Board/Remote Control Board Block Diagram
AlignRun
Hemisphere (+/-)Servo EnableDG
Acc/Cosλ
Temperature
ANALOGUE
Wheel Boost
V.Sin H.Tan
λ
R
Acc (High Gain)Acc (Low Gain)
V.Cos HR
Rate of Turn
400Hz Ref
Sin HCos H
V = speed (knots x 6080 ft/hr)
λ = local latitude (deg) H = gyro heading (deg) τ = time constant Acc = accelerometer signal
ω Sin λ
AC OK
Azimuth Pickoff (d.c.)Tilt Pickoff (d.c.)
ω = earth rotation (15°/hr)
R = earth radius (20.9 x 106 ft)
ANALOGUEMUX &10 BITADC
Tem
pera
ture
Azi
mut
h P
icko
ff (d
.c.)
Tilt
Pic
koff
(d.c
.)A
cc (L
ow G
ain)
Acc
(Hig
h G
ain)
RX TX
MAX487DRIVERRS422
P4
OPTO-COUPLER
PWMO
P2
P0
uCONTROLLER80C552
X1P4
XTAL
27C512EPROM
ADDR. BUS
DUARTSCN2681
CS
RS232/RS422 I/F
RS422DRIVERS
RS232DRIVERS
ADDR.DECODER CS
RAMHM62256
28C16AEPROM
AC OK
RESOLVERTO DIGITAL
CONVERTER
CS
LS373LATCH
AD7528DAC
CSAcc (Low Gain)
AD7528DAC
Cos H10V Ref
Sin H
AD7528DAC
10V Ref
CS
CS
CS
SCN2681DUART
CONTROL BOARDDISTRIBUTION BOARD
LS373LATCH
CS
SUPERVISORYPSU
MAX8213
DC PSU
System FailSystem Ready
Stepper O/P3 x RS232 IEC 611629 x RS422 IEC 61162RS422 Heading/ROT
GPS SerialNMEA 0183 All Data
Speed Log Serial
Speed Log Pulses
Remote Control
Course Recorder
Spare
DG Mode
RS422 I/FRS232/
CS
DAT
A B
US
DIGITAL CONTROL BOARD
400Hz RefCos H
Sin H
REMOTE CONTROL BOARD
ADDR. BUS
Remote Control
P4
uCONTROLLER
RX
MAX487DRIVERRS422
MAX813LWATCHDOG
80C32X1 XTAL
PWMO
P2
P0
TX
CS
EPROM28C16A
HM62256RAM
ADDR.DECODER
EPROM27C512
DA
TA B
US
WD1 PFO
RESET RESETCS
CS
CS
DISPLAYDRIVER
CS
LATCHLS373
CS
LS373LATCH
DISPLAY
READYSYSTEM
SOUNDERFAIL
KEYBOARD
Section 5 Page 10 of 12 Issue 3.11 © TSS (International) Ltd DPN 060070
Maintenance
Table 5–3: Spares list for Meridian Gyrocompass
TSS P/N Description
929033 Gimbal assembly
929066 Control Board Analogue
929083 Control Board Digital
929049 Control Board Remote
929045 Display Board
929074 DC/DC Power Supply
856000 Filter #1 (Schaffner)
929160 Filter #2 (Vicor)
346808 Fuse link 3.15A 250V
929164 Gland Plate assembly
929190 RCU Mounting Kit
930626 Transit case
929220 Test box
DPN 060070 © TSS (International) Ltd Issue 3.11 Section 5 Page 11 of 12
Meridian Gyrocompass
Section 5 Page 12 of 12 Issue 3.11 © TSS (International) Ltd DPN 060070
Index
AAdjustments
Azimuth bias 5–3Azimuth drift 5–2Test connector 5–3Tilt bias 5–2
Alignment 2–4, 2–13Analogue Rate of Turn
DIP-switch settings 2–12Output connection 2–9Specification 4–2, 4–17
Azimuth bias adjustment 5–3
CCable types 2–4Cautions
All 1–1Handling 2–2Making external connecting 2–5Operating limitations 4–1Power supply 4–1Removing power 2–2Repair and adjustment 5–1See WarningsTilt limits 2–3Ventilation 2–3
Controls 3–2Corrections
See Latitude CorrectionSee Speed Correction
Course recorder output 4–16
DDG Directional Gyro 3–5DIP switches 2–11Dip switches
Analogue rate of turn 2–12Outputs 2–12Vessel dynamics 2–12
EError modes
GPS 3–6Gyro failure 3–7, 3–8Relay output connections 2–9See MaintenanceSpeed log 3–6
GGPS
Baud Rates 4–2Corrections for gyrocompass 1–3, 1–5Data formats 4–4Input socket connections 2–8Loss of GPS 3–6
Gyro failure 3–7Gyrocompass configuration 2–11
HHigh Speed Craft
See Vessel Dynamics
IIEC61162
Data Format 4–5Input data formats 4–6Specification 4–3
InputsConnections 2–8Power connections 2–7Pulsed speed log 4–10Speed log 4–9
InstallationAlignment 2–4, 2–13Choosing a location 2–3DIP switches 2–11Installation Drawings 2–14Suitable cables 2–4Tools 2–4Vessel Dynamics 3–10
LLatitude Correction
Automatic 1–5Enabling 3–4GPS data formats 4–4Manual 3–4RCU display formats 3–2
MMaintenance
Error modes 3–6Operation during lay-up 3–9Test box 5–1Test connector 5–3
DPN 060070 © TSS (International) Ltd Issue 3.11 Index Page 1 of 2
Meridian Gyrocompass
NNMEA
Data Format 4–5Input data formats 4–6Log input data formats 4–9Specification 4–3
NMEA data formats 4–5
OOperation
Continuous operation 3–9During lay-up 3–9Power failure 3–9Power-off 2–2, 3–9Power-on 3–3Vessel Dynamics 3–10
Output formatsAnalogue rate of turn output 4–17Course recorder 4–16Resolver 4–16Serial NMEA / IEC61162 4–5Stepper S-code 4–17Synchro 4–16
OutputsApplication 1–5Connections 2–9Data formats 4–4
PPower
Before switching-on 3–3Supply requirements 4–1Switching off 2–2, 3–9
RRate of Turn
See Analogue Rate of TurnSerial data format 4–12
RCUControls 3–2Description 1–4Dimensions and Weight 4–2Display formats 3–2External connections 2–8, 2–9External location 2–10Installation Drawing 2–16
Resolver output 4–16
SSpeed Correction
Automatic 1–5Enabling 3–5GPS data formats 4–4Input connections 2–8Log Data formats 4–9Pulsed log input 4–10RCU display formats 3–2
Speed LogBaud Rate 4–2Input connections 2–8Loss of speed signal 3–6Serial data formats 4–9
Stepper S-code output 4–17Synchro output 4–16Synchro output connections 2–9
TTest box 5–1Test connector 5–3Tilt bias adjustment 5–2
VVessel Dynamics
Dip switches 2–12Operating considerations 3–10
WWarnings
All 1–1Disposal 4–2Lifting 2–2Safety of personnel 5–1See CautionsSee Error Messages
Index Page 2 of 2 Issue 3.11 © TSS (International) Ltd DPN 060070
top related