air conditioning parts & accessories - airefrig · air conditioning parts & accessories...
TRANSCRIPT
Air Conditioning Parts & Accessories
52723_LATEN Brochure 08.indd 2 3/3/10 5:09:08 PM
Index
DUCTS & ACCESSORIES 3.
DRAIN DUCTS & PIPE 6.
CONDENSATION PUMPS 7.
MOUNTBLOCS & BRACKETS 8.
AEROPAD & AEROSTAND 9.
PIPE CLIPS 10.
LATENT TWIN TUBE 17.
CELFLEX 18.
52723_LATEN Brochure 08.indd 4 4/3/10 12:22:59 PM
Pipe Duct & AccessoriesLatent duct and accessories are made of rigid P.V.C which offers a
never changing aspect. The duct and accessories are fade-proof,
U.V resistant and fireproof.
Thanks to the advantage of P.V.C and its linear structure, they are
very harmonious with any type of construction or building offering
an outstanding quality finish.
The easy to install ducts have a bottom and upper section. The
bottom is first fixed to the wall. Then you fix the pipe, wiring and
bind them with the Tie Clip (that slides along the inside rail). Finally
cover them with the snap on upper section.
All accessories that are two part are supplied with stainless steel
screws to prevent rusting and unsightly stains.
Mounting blocks will support upto 240Kg. Each mount is supplied
with 2 x bolts, nuts & washers. End caps and galvanised tie down
setting plates are available to suit.
Wall & roof adjustable brackets are made from galvanised powder
coated steel.
Mount pads are made from E.P.D.M. which is an outstanding
ultraviolet & weather resistant material.
Three wall bracket sizes: 60 Kg, 80 Kg, 150 Kg
Roof brackets are adjustable from 3 to 30 degrees and have a load
rating of 80 Kg.
Wall & Roof Brackets
52723_LATEN Brochure 08.indd 5 3/3/10 5:09:12 PM
Ducts & AccessoriesDUCTS
Easy to install ducts which have an upper and lower section. Snap fit upper section after installation of pipes and electrics.
PART NUMBER A B LENGTH LENGTHS/BOX
D70 70 65 2000 6
D105 105 75 2000 6
D150 150 80 2000 6
B
A
WALL COVERPerfect finish for all wall penetrations.
PART NUMBER A B C PIECES/BOX
WC70 110 180 70.4 20
WC105 145 190 105.4 20
WC150 235 150 150 20
B
CA
FLAT BEND 90°For 90 degree directional changes on the same plane
PART NUMBER A B C PIECES/BOX
FB70 115 115 70.4 20
FB105 150 150 105.4 20
FB150 165 165 150 20
C
B
A
FLAT BEND 45°For 45 degree directional changes on the same plane
PART NUMBER A B C PIECES/BOX
FB7045 92 145 70 20
FB10545 92 170 105 20
FB15045 80 187 150 20
B
C
A
3.
52723_LATEN Brochure 08.indd 6 3/3/10 5:09:14 PM
Ducts & Accessories
FLEXIBLE JOINTChanging direction of duct where standard elbows are unsuitable.
PART NUMBER A B C PIECES/BOX
FJ70 500 65 65 20
FJ105 500 100 100 20
A
C
B
T-JOINTUseful in the installation of multi split systems or multiple systems.
PART NUMBER A B C PIECES/BOX
TJ105 105.4 105.4 200 20
TJ150 150 150 245 20
A
B
C
ELBOW IN-CORNER 90°Directional change of 90 degree with the building corner in the throat of the elbow allowing rear side access.
PART NUMBER A B C PIECES/BOX
EIN70 95 95 70.4 20
EIN105 110 110 105.4 20
EIN150 125 125 150 20
A C
B
ELBOW BEND 90°Directional change of 90 degree with the building corner at back of elbow, allowing throat access to the elbow.
PART NUMBER A B C PIECES/BOX
EB70 95 95 70.4 20
EB105 110 110 105.4 20
EB150 125 125 150 20
CA
B
4.
52723_LATEN Brochure 08.indd 7 3/3/10 5:09:16 PM
Ducts & AccessoriesREDUCER JOINTConnects D105 to D70 duct and D70 duct to a T joint.
PART NUMBER A B C PIECES/BOX
RJ70105 105.4 80.4 70.4 20
RJ105150 150 85 105 20
A
B
CCONNECTION PIECEDuct straight connector.
PART NUMBER A B C PIECES/BOX
CP70 75.4 70.4 70.4 20
CP105 110 110 105.4 20
CP150 155 90 60 20
CA
BDUCT ENDCloses over insulated pipe tails reducing vermin access to building.
PART NUMBER A B C PIECES/BOX
DE70 70.4 120 45 20
DE105 105.4 120 50 20
DE150 150 150 53 20
A C
BDUCT CAPSeals end of duct reducing vermin access to building.
PART NUMBER A B C PIECES/BOX
DC70 70 65 2 20
DC105 105 75 2 20
THE TIEClips and slides along inside duct rail for fastening pipes and electrics.
PART NUMBER PIECES/PACKET
TCLIP 100
A
C
B
5.
52723_LATEN Brochure 08.indd 8 3/3/10 5:09:18 PM
Ducts & AccessoriesWALL ROSETTEFlashing for wall or eaves penertration.
PART NUMBER A B C PIECES/BOX
WR70 115.4 110.4 70.4 20
WR105 150.4 120.4 105.4 20
WR150 195 125 150 20A
B
CFLAT ROSETTEFlashing for wall or eaves penertration with one flat side.
PART NUMBER A B C PIECES/BOX
FR70 115.4 90 70.4 20
FR105 150.4 100 105.4 20
FR150 195 105 150 20
A
B
C
6.
Drain Ducts & PipeDRAIN PIPE DUCT & FITTINGSEasy to install ivory coloured and UV resistant drain pipe duct. One piece duct with hinge lid that simply clips into place.
PART NUMBER DESCRIPTION
DPD Drain Pipe Duct - 2000mm (L) x 32mm x 30mm
DPCI Drain Pipe In Corner
DPCO Drain Pipe Corner Out
DPFE Drain Pipe Flat Elbow
DPC Drain Pipe Connector
DPWC Drain Pipe Wall Cover
FLEXIBLE DRAIN PIPEFlexible drain pipe - Pipe has cut marks each metre for connection to 16mm and 18mm systems.
PART NUMBER DESCRIPTION
DP93ROLL Drain pipe - boxed 50 metre roll
DP93MTR Drain pipe - per metre
CCY “Y” connector to suit DP93 drain pipe
DPD DPCI DPC DPFE DPWC DPCO
52723_LATEN Brochure 08.indd 9 3/3/10 5:09:20 PM
Condensation Pumps
7.
The EE400 condensate pump is designed to automatically remove water from air conditioners and evaporator coils etc. This pump has its own 0.5 litre reservoir / tank but can be taken out of its housing and placed into an external pan if required (max pan height is 70mm)
PART NUMBER CAPACITY HEAD
EE400
350 litres / hour 0 metres
280 litres / hour 1 metre
220 litres / hour 2 metres
100 litres / hour 3 metres
0 litres / hour 4 metres
The EE150 condensate pump is designed to automatically remove water from air conditioners and evaporator coils etc. This pump has its own 0.2 litre reservoir / tank.
PART NUMBER CAPACITY HEAD
EE150
120 litres / hour 0 metres
80 litres / hour 1 metre
0 litres / hour 1.5 metres
The EE1750 condensate pump is suitable for integration into mini split, ceiling and wall mounted air conditioning units. The pump assembly is comprised of two parts - the pump & float switch.
PART NUMBER CAPACITY HEAD
EE1750
32 litres / hour 0 metres
22 litres / hour 5 metres
11 litres / hour 10 metres
0 litres / hour 15 metres
The EE2000T1 condensate pump is suitable for integration into mini split, ceiling and wall mounted air conditioning units. The pump assembly is comprised of two parts - the pump & float switch.
PART NUMBER CAPACITY HEAD
EE2000T1
10 litres / hour 0 metres
7.5 litres / hour 2 metres
5 litres / hour 4 metres
2 litres / hour 6 metres
CONDENSATE PUMPS
The EE1200 condensate pump is integrated into a Latent Duct Elbow (FB105) allowing it to be installed directly on the outside of the air conditioner. The pump assembly is suitable for mini split, ceiling and wall mounted air conditioners
PART NUMBER CAPACITY HEAD
EE1200
8 litres / hour 0 metres
6 litres / hour 2 metres
4 litres / hour 4 metres
2 litres / hour 6 metres
52723_LATEN Brochure 08.indd 10 3/3/10 5:09:23 PM
8.
Mountblocs & BracketsMOUNTBLOC
Light weight, rigid supports up to 240kg each, easy to install, adapted to all units, complete with mounting bolts.
PART NUMBER WIDTH HEIGHT LENGTH PIECES/BOX
EXW38 105 95 350mm 12
EXBW38 105 95 450mm 12
END CAPSnap on, end cap, for mountblocs.
PART NUMBER DESCRIPTION PIECES/PACK
INJW181 END CAP SET 4
ANCHOR SETGalvanised steel anchor set for mountblocs, complete with setting bolts.
PART NUMBER DESCRIPTION PIECES/PACK
A12 Anchor Set 4
WALL BRACKETStrong, lightweight, fully adjustable bracket made of galvanised, powder coated steel.
PART NUMBER A B C MAX LOAD
EJP60 700 450 380 60kg
EJP80 1050 590 490 80kg
EJP150 750 650 Leg 150kg
Composite Wall Bracket
SBP46PUL 790 410 460 80kg
A
B
C
ROOF BRACKET
Strong, light weight, fully adjustable bracket made of galvanised, powder coated steel. Adjustable from 3 to 30 degrees.
PART NUMBER DESCRIPTION MAX LOAD
EJPRB80 Adjustable Roof Bracket (1050 x 590 x 350) 80kg
52723_LATEN Brochure 08.indd 11 3/3/10 5:09:27 PM
Aeropad & AerostandAEROSTAND
Aerostand is made from natural rubber blended with EPDM synthetic rubber and is a load support specifically designed for air-conditioning units. This stand possesses both high compressive strength and good weathering resistance. It is very effective in reducing vibration and noise levels.
SPECIFICATIONS DESCRIPTION
Tensile Strength Minimum 6.5 MPa
Elongation Minimum 250%
Hardness 70 ± 5 Shore A
Compression Strength @ 10% Deflection Minimum 0.75 N/mm2
Maximum Compression Strength Minimum 5.0 N/mm2
Tear Strength Minimum 15 kgf/cm
Maximum Load 50kg per stand
ANTI-VIBRATIONPART NUMBER DESCRIPTION
AEROPAD10 Anti Vibration Pad 1000 x 100 x 10mm
AEROPAD15 Anti Vibration Pad 1000 x 100 x 15mm
AEROSTAND075 Machinery Mount 75mm High Max Load 50kg per stand (set of 4)
Aeropad Aerostand
9.
52723_LATEN Brochure 08.indd 12 3/3/10 5:09:28 PM
10.
Rapid Pipe Clips
CLIP INSIDE DIAMETERPART
NUMBER METRIC IMPERIAL PACK QUANTITY
RPC38 10mm 3/8” 10
RPC12 12mm 1/2” 10
RPC58 15mm 5/8” 10
RPC34 20mm 3/4” 10
RPC78 22mm 7/8” 10
RPC118 28mm 1 1/8” 10
RPC138 35mm 1 3/8” 10
RPC158 42mm 1 5/8” 10
MATERIAL PROPERTIES
nylon, but with superior impact strength especially at lower temperatures.oC to +140
oC.
o
RAPID PIPE CLIP
The Rapid Pipe Clip is made from a composite polyamide alloy combining strength with light weight, the clip is easy and fast to install. This one piece single hand fixing requires no mechanical aids, completely sealing the pipe work or cable. The RPC is designed to fit all pre-formed channels of a profile width of 41mm with an inturned channel lip of 10mm width or 7mm depth.
It will not tighten down on pipe work therefore eliminating possible cracks or fractures.
52723_LATEN Brochure 08.indd 13 3/3/10 5:09:28 PM
Rapid Pipe Clips
INSUL PIPE CLIP
The InsulClip has been developed by Rapid Positioning Clips Ltd., to combine the advantages of the proven RPC channel foot and the versatile collar that allows the installation of pipe work with imperial or metric outside diameters.
The great advantage is the InsulClip allows an unbroken vapour barrier seal, eliminating the problem of sweating on metal fittings. The clip is ideal for the installation of VRV systems allowing the barrier seal to run the length of the pipe work without breaks in insulation material. The clip secures both the pipe and insulation.
CLIP INSIDE DIAMETERPART
NUMBER METRIC IMPERIAL PACK QUANTITY
IC0015 15mm 5/8” 10
IC0020 20mm 3/4” 10
IC0022 22mm 7/8” 10
IC0025 25mm 1” 10
IC0028 28mm 1 1/8” 10
IC0032 32mm 1 1/4” 10
IC0035 35mm 1 3/8” 10
IC0040 40mm 1 1/2” 10
IC0042 42mm 1 5/8” 10
IC0050 50mm 2” 10
IC0054 54mm 2 1/8” 10
11.
52723_LATEN Brochure 08.indd 14 3/3/10 5:09:29 PM
12.
STUDDING (THREADED ROD) - PIPE CLIP
The Studding Pipe Clip is a unique one-piece design manufactured from a composite Polyamide Alloy combining strength with lightweight. It will overcome the problems of using cable ties for piping, electrical, optical and network cabling. The studding pipe clip is extremely quick and simple to use, fitting effortlessly on conventional 8mm and 10mm (European standard) and 3/8” (US Standard) studding.
The solid connection can be adjusted up and down by simply rotating the clip that uses the stud thread as if it were a nut. The studding clip is a major advance in efficiency for the installation of air conditioning, refrigeration, plumbing pipe work, electrical conduit as well as network and optical cabling.
CLIP INSIDE DIAMETERPART
NUMBER METRIC IMPERIALFITSSTUD
Ø
PACKQTY
SC1015 15mm 5/8” 10mm 10
SC1020 20mm 3/4” 10mm 10
SC1022 22mm 7/8” 10mm 10
SC1025 25mm 1” 10mm 10
SC1028 28mm 1 1/8” 10mm 10
SC1032 32mm 1 1/4” 10mm 10
SC1035 35mm 1 3/8” 10mm 10
SC1040 40mm 1 1/2” 10mm 10
SC1042 42mm 1 5/8” 10mm 10
SC1050 50mm 2” 10mm 10
SC1054 54mm 2 1/8” 10mm 10
Rapid Pipe Clips
52723_LATEN Brochure 08.indd 15 3/3/10 5:09:29 PM
Beta ClampBETA CLAMP
The Beta Clamps are suitable for clamping pipes, hoses and electric cables. These are a sensible and easy way of securing piping and hoses in all types of installations.
The main features of Beta Clamp are its shock-absorption, vibration dampening and noise reducing properties.
Beta Clamps have a practical and economical design, which make for quick, easy pipe installation and layout.
Using weldable plates, it’s easy to anchor the clamps to machinery and steel work.
Fast, safe and economic installation.
Upper and lower clamp halves are identical.
Ribs in clamp bore are designed to absorb shock and vibration.
High sound absorption is guaranteed.
Clamp Body: Standard-Polypropylene (Green Color) -30°C to +90°C
Lower and upper plates: Steel, 304S/S
Screw Bolts: Steel, S40C, 304S/S
PARTNUMBER SIZE A1 A2 A3 H1 H2 HEXBOLT
IC0015 1/4” 20mm 34mm 34mm 16mm 32mm 1/4”-20 x 1-1/4”
IC0020 3/8” 20mm 34mm 34mm 16mm 32mm 1/4”-20 x 1-1/4”
IC0022 1/2” 26mm 40mm 42mm 19.5mm 39mm 1/4”-20 x 1-3/8”
IC0025 5/8” 26mm 40mm 42mm 19.5mm 39mm 1/4”-20 x 1-3/8”
IC0028 3/4” 33mm 50mm 52mm 20.5mm 41mm 1/4”-20 x 1-1/2”
IC0032 7/8” 33mm 50mm 52mm 20.5mm 41mm 1/4”-20 x 1-1/2”
IC0035 1” 33mm 50mm 52mm 20.5mm 41mm 1/4”-20 x 1-1/2”
IC0040 1 1/8” 40mm 58mm 60mm 24mm 48mm 1/4”-20 x 1-3/4”
IC0042 1 1/4” 52mm 70mm 72mm 32mm 64mm 1/4”-20 x 2-1/2”
13.
52723_LATEN Brochure 08.indd 16 3/3/10 5:09:30 PM
14.
Cush-a-Grip™
CUSH-A-GRIP
PART NUMBERCOPPER TUBE
OD SIZEPIPE SIZE Ø
CG10 1/4” 3/8” 1/2” 1/4” 6-14mm
CG20 5/8” 3/4” 7/8” 3/8” 1/2” 15-22mm
CG30 7/8” 1” 1-1/8” 3/4” 22-28mm
CG40 1” 1-1/8” 1-1/4” 3/4” 1” 26-32mm
Multi-size adjustment capability allows four clamp sizes to fit fifteen sizes of tube and pipe
Features:
Advantages:
requirements on projects using both tube and pipe sizes
Benefits:
hand when you need it
more accurate
Complete with stainless steel bolt and captured nylon lock nut
Features:
Advantages:
Benefits:
Made from high-strength temperature-adverse, UV resistant, nylon reinforced TPI material
Features:
Advantages:
of steel
Benefits:
with steel tube
applications and maintains thermal barrier
aluminium, PCV or hot dipped galvanised clamps
52723_LATEN Brochure 08.indd 17 3/3/10 5:09:30 PM
15.
Cush-a-Claw™
Cush-A-Claw™ is a unique one-piece patented pipe clip system designed for quick, simple and easy installation.
The Cush-A-Claw™ is a channel mounted clamping system molded from rust free TPE (thermoplastic elastomer) material that grabs easily on to pipe or hose and holds it in place.
Features
CUSH-A-CLAW
AIREFRIGPART NUMBER
SIZE RANGETUBE O.D.
mm Inches
CL06PKT 9.5 3/8
CL08PKT 12.7 1/2
CL10PKT 15.9 5/8
CL12PKT 19.1 3/4
CL14PKT 22.2 7/8
CL18PKT 28.6 1 1/8
52723_LATEN Brochure 08.indd 18 3/3/10 5:09:31 PM
Cush-a-Clamp®
CUSH-A-CLAMP
CUSH-A-CLAMP® channel mounted clamping systems are ideal for multiple pipe runs, while absorbing shock and vibration, reducing unwanted noise and preventing galvanic corrosion.
Manufactured from a thermoplastic elastomer, it’s built tough to withstand the effects of most oils, chemicals and industrial cleaning compounds, in temperatures from -45°C to 135°C. A patented “Living Hinge” allows the cushion to be spread apart for quick, easy installation. Interlock edges and channel locater legs insure that the cushion remains in place.
PARTNUMBER
DIM“A”
DIM“B”
DIM“C”
DIM“D”
004T008 1/4” 15.7mm 6.9mm 24.9mm
006T010 3/8” 20.8mm 8.4mm 28.7mm
008T012 1/2” 23.9mm 10.2mm 34.0mm
010T014 5/8” 26.9mm 11.7mm 39.1mm
012T016 3/4” 30.5mm 13.2mm 42.7mm
014T018 7/8” 33.3mm 14.7mm 46.2mm
016T020 1” 36.6mm 16.5mm 49.5mm
018T022 1 1/8” 39.9mm 17.8mm 52.8mm
020T024 1 1/4” 43.2mm 19.6mm 56.1mm
022T026 1 3/8” 46.2mm 21.1mm 59.4mm
024N028 1 1/2” 49.5mm 22.9mm 62.7mm
026N030 1 5/8” 52.6mm 24.4mm 66mm
028N032 1 3/4” 55.9mm 25.9mm 69.3mm
030N034 1 7/8” 58.9mm 27.7mm 72.6mm
032N036 2” 62.2mm 29.2mm 77.2mm
034N040 2 1/8” 65.3mm 32.3mm 82mm
042N048 2 5/8” 77.9mm 38.8mm 99.5mm
Thermoplastic elastomer withstands most oils, chemicals and cleaning compounds
Nylon-insert lock nutassures positive lock
“Controlled-Squeeze” studeliminates over-tightening
Steel with electro-dichromate finish
Standard 1-5/8” wide channel
16.
52723_LATEN Brochure 08.indd 19 3/3/10 5:09:32 PM
Latent Twin TubePRE-INSULATED COPPER TUBE
COPPER TUBE DIMENSIONS
PART NUMBER IMPERIAL METRICINSULATION THICKNESS
LENGTHMETRES
23201/43/8
6.35 x 0.89.52 x 0.8
10mm10mm
2020
24201/41/2
6.35 x 0.812.7 x 0.8
10mm10mm
2020
25201/45/8
6.35 x 0.815.8 x 1.0
10mm10mm
2020
35203/85/8
9.52 x 0.815.8 x 1.0
10mm10mm
2020
3620H3/83/4
9.52 x 0.819.05 x 1.2
10mm10mm
1010
Suitable for R410A
Twin Tube is manufactured using High Quality Seamless Copper Tube suitable for use with new generation refrigerants in the Air Conditioning and Refrigeration fields.
Twin Tube insulation is manufactured from cross-linked, closed cell polyethylene film.The exterior embossed polyethylene film is stronger and more resistant to abrasion than traditional materials, enabling ease to pass through tight spaces without being torn.
Save time and money.Install pipework in less time with pre-insulated annealed copper Twin Tube in sizes from 1⁄4” (6.35mm) to 3⁄4” (19.1mm), see above
The 20 metre Twin Tube coils are packed in cardboard cartons for easy of transport and handling.
Continuous 20 metre Twin Tube coil lengths eliminates the need to seal insulation joints, apply glue or tape saving time and money.
The Twin Tube pre-insulated tubes are glued together and can be easily split by hand if required.
17.
52723_LATEN Brochure 08.indd 20 3/3/10 5:09:33 PM
Celflex®
LENGTHS & CONTINUOUS INSULATION
Celflex® Continuous Tube is specially designed for long pipe runs on split -type air conditioning systems. Installation will be quicker & easier using continuous tube.
Features:
FIRE RATING AUSTRALIAN STANDARD AS1530.3 - 1999
Ignitability Index 17 (range 0-20)
Spread of Flame Index 9 (range 0-10)
Heat Evolved Index 8 (range 0-10)
Smoke Developed Index 8 (range 0-10)
*To be read in conjunction with the Building Code of Australia
*To be
CELFLEX PIPE INSULATIONPART NUMBER WALL ID LENGTH
CF09006
9mm
6mm
2m
CF09010 10mm
CF09013 13mm
CF09016 16mm
CF09019 19mm
CF09022 22mm
CF09025 25mm
CF09028 28mm
CF13006
13mm
6mm
CF13010 10mm
CF13013 13mm
CF13016 16mm
CF13019 19mm
CF13022 22mm
CF13025 25mm
CF13028 28mm
CONTINUOUS CELFLEX PIPE INSULATIONPART NUMBER WALL ID LENGTH
C09006
9mm
6mm 76m
C09010 10mm 63m
C09013 13mm 47m
C09016 16mm 40m
C09019 19mm 33m
18.
52723_LATEN Brochure 08.indd 21 3/3/10 5:09:33 PM
FREE CALL 1800 671 500Email: [email protected]
www.airefrig.com.au
320102M
WESTERN AUSTRALIA75 Beechboro Road, Bayswater, WA, 6053
Telephone: (08) 9272 8977 Facsimile: (08) 9370 2868
4 Sleeman Close,O’Connor, WA, 6163
Telephone: (08) 9314 1441 Facsimile: (08) 9337 4192
17/8 Baretta Road, Wangara, WA, 6065
Telephone: (08) 9309 9300 Facsimile: (08) 9309 9611
NEW SOUTH WALES10/4 Avenue of Americas, Newington, NSW, 2127
Telephone: (02) 9648 1414 Facsimile: (02) 9648 1717
64 Gibson Avenue, Padstow, NSW, 2211
Telephone: (02) 8708 8333 Facsimile: (02) 8708 5334
VICTORIA29 Geddes Street,
Mulgrave, VIC, 3170Telephone: (03) 9561 7200Facsimile: (03) 9561 7911
18 Macquarie Drive, Thomastown, VIC, 3074
Telephone: (03) 9464 3844 Facsimile: (03) 9464 3833
QUEENSLAND127 Gardens Drive,
Willawong, QLD, 4110Telephone: (07) 3272 4844 Facsimile: (07) 3272 4644
29 - 35 Huntington Place, Banyo, QLD , 4014
Telephone: (07) 3267 0888 Facsimile: (07) 3267 0111
SOUTH AUSTRALIA10 Wirriga Street,
Regency Park, SA, 5010Telephone: (08) 8345 2201Facsimile: (08) 8345 2401
52723_LATEN Brochure 08.indd 1 4/3/10 12:23:49 PM