admiralty inlet pilot tidal project · construction, monitoring, and operation of the project,...

ADMIRALTY INLET PILOT TIDAL PROJECT

Marine Aquatic Resource Committee May 19, 2014 1

MARC Members As stated in the FERC License, the MARC is comprised of: • Snohomish PUD (District) • National Marine Fisheries Service (NMFS) • U.S. Fish and Wildlife Service (USFW) • Washington Department of Fish and Wildlife (WDFW) • Washington Department of Ecology (Ecology) • Washington Department of Natural Resources (DNR) • Tulalip Tribes • Suquamish Tribe • Swinomish Indian Tribal Community • Sauk-Suiattle Tribe Additional members may be added by unanimous agreement by the MARC.

2

Purpose and Key Functions of MARC

• Purpose of MARC is to advise the District on aquatic resource issues related to construction, monitoring, and operation of the Project, including:

– Review results of project monitoring

– Review and comment on proposed changes to monitoring plans, as required and as necessary due to adaptive management triggers

3

Establishment of MARC

• No separate license article establishing MARC

• FERC is “requiring implementation of monitoring plans, including the consultation and adaptive management requirements.”

• FERC lacks authority to require any entity to participate, but requires the District to document consultation with MARC entities on specific monitoring plans

4

Adaptive Management Framework

• Purpose of meetings will be to review required consultation materials and discuss questions

• During project operation, MARC will review results of monitoring plan studies

• Group will follow the Adaptive Management Framework and seek to reach consensus when a vote is necessary; however some meetings will not require voting

5

• Frequency of meetings will be determined by milestone events such as:

– Required consultation document is due

– Project monitoring results are compiled

– Monitoring plan changes are proposed

– Adaptive management trigger is initiated

6

Adaptive Management Framework

MARC Consultation Requirements The FERC License requires consultation on any proposed changes to the following: • Acoustic Monitoring and Mitigation Plan (Article 404) • Benthic Habitat Monitoring and Mitigation Plan (Article

405) • Near-Turbine Monitoring and Mitigation Plan (Article 406) • Marine Mammal Monitoring and Mitigation Plan (Article

407) • Derelict Gear Monitoring Plan (Article 409) • In-water construction schedule (Article 410) In addition, development of the Project Removal and Site Restoration Plan is a condition of Ecology’s 401 WQC and requires MARC consultation.

7

8

Project Installation Overview

Project Implementation Partners

9

PCCE Supply Sub-Contractor

REGIONAL MAP

10

OVERVIEW MAP

Marine Cables

HDD

11

TURBINE DEPLOYMENT SITE

12

OVERVIEW MAP

Marine Cables

HDD

13

ONSHORE DETAILS

OVERVIEW

1. TRANSFORMERS 2. POWER CONTROL &

CONDITIONING BLDG. (PCCB)

3. BATTERY STORAGE SYSTEM

4. GRID CONNECTION EQUIPMENT

5. CONCRETE FENCED YARD

LESS BUSY

TO G

RID

14

15

Power Conditioning and Control Building

16

HORIZONTAL DIRECTIONAL DRILLING (HDD)

• 600 lineal feet under the shoreline environment

• Minimum 2-6” diameter conduits

• 19-meters – requiring shallow dive support

• Avoids conflicts with sensitive near-shore habitat

DETAILED MARINE OPERATIONS

• Marine Operations separated into 3-discrete operations with limited coordination requirements:

Cable Installation (Qty-2) – By PWC

Turbine Deployment (Qty-2) – By OpenHydro

Cable Connection (Qty-2) – By PWC

17

Cable Installation - PWC

18

• Barge of opportunity PWC Leased Self powered or Z-Drive tug powered

• Equipment spread PWC Leased, owned or fabricated

equipment

Typical Cable Lay Vessel

Cable Installation - PWC

19

START HERE

HDD

20

Cable Installation 1. Surface laid cable 2. 24-HOUR OPERATION 3. Standby Tugs onsite for entire duration 4. ROV Monitors Cable Installation 5. 35,000# cable working strength

Cable Installation – By PWC

Subsea Cable Skid (SCS)

ROV Support Vessel Cable Lay Vessel

ROV


21

Cable-Lay Vessel continues operation until it reaches Admiralty Bay. Vessel is arranged into a 4-point moor near the HDD exit E

W

Acoustic Release Buoy

Preset 4-Point Mooring Anchors

& Lines CALM WATERS OF

ADMIRALTY BAY

22

E

W

Small Assist Vessel

Cable Buoy Float

Blue Line: End of Main Export Cable to Shore Red Line: Main Export Cable from Turbine


HDD Pull Head (HPH)

23

E

W

Shore Cable 1. Assist Vessel Arrives at End of HDD near Shoreline


HDD CONDUIT


24

Shore Cable 1. Assist Vessel Arrives at Shoreline 2. Dynamometer Monitors Tension on CLV 3. Diver Monitors Installation at Bellmouth

Small Assist Vessel

Floatation Buoy

HDD Pull Head (HPH)

Existing HDD Pipe With Bellmouth

Pull Line

19 m


25

Shore Cable 1. Assist Vessel Removes Floatation Buoys as Needed 2. Diver Monitors Cable Catenary and Directs Cable through

the HDD

Trunk Cable

26

Shore Cable 1. Cable End Loop is Maneuvered Out of the Pan & Chutes 2. Excess Cable in Bay is Being Pulled Through HDD 3. Floatation Buoys are Being Removed at HDD End

Final Cable “Loop”


27

Shore Cable 1. Final Cable Loop is Lowered Over Cable Chute 2. Assist Vessels Continue Monitoring Installation


28

Shore Cable 1. Floatation Buoys are Removed at Each End. 2. Cable Catenary is monitored by Diver & Assist Vessels


29

Shore Cable 1. Cable is Installed on Seabed in Final Position 2. Remaining Buoys are Removed as Cable End is Pulled Through HDD 3. Diver Monitors Installation


30

Shore Cable 1. Final Cable Position 2. Remaining Slack is Removed from Cable 3. Second Cable is a repeat performance


Turbine Deployment By OpenHydro

31 “OpenHydro Installer” Barge

Tug

Legend:

Umbilical Cable

Barge Winch Cable

Marker Buoy

OpenHydro Arrives on Station. Unit positioned over site & lowered.

OpenHydro Turbine Deployment

32

Legend:

Umbilical Cable

Barge Winch Cable

Marker Buoy

Fine timing of positions using tug tow line & 2-drives. Direction of tide & flow is measured & monitored closely as assembly approaches sea floor.

33


Legend:

Umbilical Cable

Barge Winch Cable

Marker Buoy

On bottom – Confirmation of positions, ensure unit is level & feet have not sunk. Release of hydraulics.

34


Legend:

Umbilical Cable

Barge Winch

Marker Buoy

Recovery frame is now disconnected from the subsea base & raised back up to the barge.

35


Cable Connection By PWC

36

Cable Lay Vessel • Winch recovers each end • Performs system health check • Completes umbilical and cable connection

• Deploys connected in-line pressure vessel

Support Vessel • Operates ROV

• Monitors operations • Records final locations

Trunk Cable Umbilical Cable

Arrival Onsite 1. Barge Arrives During Weakening Flood 2. ROV is Deployed to Recover Line from Main Export Cable End 3. Modified Construction Barge Station Keeps

Cable Connection – By PWC

37

Modified CLV or Construction Barge

ROV

Subsea Cable Skid (SCS)

Cable Recovery 1. ROV Maneuvers Towards Construction Barge


38

Cable Retrieval 1. Linear Cable Engine (LCE) Winches in Cable

End to the barge platform. 2. ROV Maneuvers Towards Subsea Base


39

Cable Retrieval 1. LCE Secures Cable End Aboard the Barge 2. System Health Check is Performed on Main Export Cable 3. Subsea Skid Remains on Seafloor for Future Use


40

FIBER LOW POWER HIGH POWER

Remove Flange Cover Plate

Fiber Test Continuity Test

Megger Test

Secured to LCE

Bend Restrictor

Cable Tail Line Retrieval 1. ROV Releases cable from Integrated Capture Device (ICD) 2. ROV Recovers a Tag Line from the Cable Platform


41

ICD

TUSP

ROV Platform

Cable Tail Line Retrieval 1. Linear Cable Engine Winches Cable Tail Towards Barge 2. ROV Docks at Subsea Base & Monitors the Cable Recovery


42

Weakening Flood

Cable Tail Line Retrieval 1. Cable Tail is Brought Aboard the Barge 2. System Health Check is Performed on Cable Tail


43

FIBER LOW POWER HIGH POWER

Remove Flange Cover Plate

Main Termination Bottle

Armor Termination

Bend Restrictor

Fiber Test Continuity Test

Megger Test

Secured to LCE

Slack water

Cable Redeployment 1. Barge Begins Lowering Cable in “S” Pattern 2. ROV Monitors Cable Placement on the Seafloor


44

Completed IPV Connection w/Bending Radius Protection”

Developing Ebb


45

Cable Redeployment 1. Connector Housing is Deployed on Seafloor 2. ROV Monitors Final Placement

Plan View of Installation

Developing Ebb

Commissioning Effort

• Coordinated Effort

Turbine System

Battery Storage System

Grid Connection System

Supervisory Control and Data Acquisition

46

Strobe

Hydrophone

ADCP

Camera

SeaEye Falcon ROV

Instrument Frame

Pilot-Scale Monitoring Objectives

Acoustic Characterization – turbine sound

Benthic Habitat – artificial reef

development, scour or sedimentation

around subsea base

Near-turbine – interactions between

aquatic species and turbine rotor

Marine Mammals – behavioral changes for

seals, harbor porpoise, and Southern

Resident killer whales in response to

turbine sound

Adaptive Monitoring Package (AMP)

47

UNIVERSITY OF WASHINGTON RECOVERABLE AMP DEVELOPMENT

48 48

Project Schedule Overview

49

Upcoming MARC Consultation Items **next meeting date TBD**

• Monitoring Objectives – Brian Polagye

• Monitoring Plan revisions

• In-water construction schedule

50

Questions

51

admiralty inlet pilot tidal project · construction, monitoring, and operation of the project,...

Documents