add_info_b-64305en_03

7/27/2019 Add_info_B-64305EN_03

http://slidepdf.com/reader/full/addinfob-64305en03 1/15

ADDITIONAL INFORMATION

7/27/2019 Add_info_B-64305EN_03


Edit. DATE Design Description

DRAW. NO

B-64305EN/03-01 CUST.01 10/03/23 New issuedSAKAMOTO

TITLE

FANUC Series 0i/0i Mate-MODEL D MAINTENANCE MANUAL

An amendment of the option information file

SHEET 1 / 3

FANUC Series 0i/0i Mate-MODEL D MAINTENANCE MANUAL

An amendment of the option information file

1. Type of applied technical documents

Name FANUC Series 0i/0i Mate-MODEL D MAINTENANCE MANUAL Spec. No.

/ VersionB-64305EN/03

2. Summary of change

Group Name / OutlineNew, Add.,

Correct, Del.

Applicable

Date

Basic

Function

Optional

Function

Unit

Maintenance

Parts

NoticeThe section 4.11 is modified.

NOTE in APPENDIX C.2.1 is modified.

Correction

Another

7/27/2019 Add_info_B-64305EN_03



DRAW. NO. B-64305EN/03-01 CUST.

TITLE

SHEET 2 / 3

The section 4.11 is changed “The option information file”,modified in the section 4.11.

4.11 The option information file

This CNC supports the “FANUC Remote Option System.”

The note in the restoration of the option information file

1) Optional parameters are stored in an option information file (with file name “OPRM INF”) in theFROM module.

Please also back up the option information file (file name: “OPRM INF”) in the FROM, when you

back up the SRAM memory and the user files. This is for easy recovery in case of data loss.

2) If once the option information file is restored, P/S alarm No.5523 (WAITING THE OPTION

CERTIFICATION) occurs when the power is turned on. Then, the certification of the option

parameters by FANUC Service is required within the expiration date (30 days (720 hour) after Alarm

occures.).

(The P/S alarm No.5523 can be canceled by reset within the expiration date.)

Request FANUC Service to certify the option parameters.

7/27/2019 Add_info_B-64305EN_03



DRAW. NO.

B-64305EN/03-01 CUST.

TITLE

SHEET 3 / 3

NOTE is modified in APPENDIX C.2.1.

C2.1 USER DATA LOADING/SYSTEM DATA LOADING Screen

NOTE1 The option parameters of the CNC are saved in the option information file (OPRM

INF). If this file is modified, the option parameters need to be certified because thesettings of the option parameter are assumed to be changed by FANUC Service.Request FANUC Service to certify the option parameters.

2 Since the option information file (OPRM INF) may be necessary when the printedcircuit board is replaced, it is recommended that this file be backed up in advanceas in SRAM data.

7/27/2019 Add_info_B-64305EN_03


Ed Date Design Description

TITLE

DRAW. NO B-64305EN/03-02

SHEET

01 Nov.11, 2010 Tatemura

FANUC Series 0i / 0i Mate-MODEL DThe method to attach a protection sheet toa LCD unit

1/ 8FANUC Corporation

CUST

About Additional Section of FANUC Series 0i/0i Mate-MODEL D Maintenance Manual


Name FANUC Series 0i/0i Mate-MODEL D Maintenance Manual

Spec.No.／ Version

B-64305JA/03

2. Summary of changes

Group Name / OutlineNew, Add,Correct,Delete

ApplicableDate

BasicFunction

OptionalFunction

Unit

Maintenance

NoticeSection 2.12 is added.

Correction

Another

7/27/2019 Add_info_B-64305EN_03



TITLE

DRAW. NO B-64305EN/03-02

SHEET




CUST

2.12 How to attach a protection cover

1. Summary

Please use a protection cover on the screen of the LCD unit in extreme environments such as oilor dust spatters down all the time.

The following shows how to attach the protection cover.

2. The specification of the protection cover

The following is the specification of the protection cover.

3. How to attach a protection cover

If the LCD unit has another protection cover or protection sheet for the touch panel, peel off itfrom the screen. Sometimes adhesive might remain on the screen. In that case, remove it usingan adhesive tape. Wiping off with solvent may make the screen dirty.

Before attaching a protection cover, wipe off oil and smears completely from the ornamentalframe, the LCD surface and the soft key surface, using ethanol or diluted neutral detergent(suchas kitchen detergent). If you use neutral detergent, remove remaining detergent completely,using a wet cloth. Remaining oily substance or detergent causes the protection cover to comeoff the display. After you make sure that the ornamental frame is dry, follow the procedure belowto attach the protection cover. At that time, prevent dust from entering between the LCD unit andthe protection cover.

1) 10.4'' LCD2) 8.4'' horizontal LCD/MDI3) 8.4'' vertical LCD/MDI

Unit Specification8.4”vertical LCD/MDI A02B-0319-K138

8.4”horizontal LCD/MDI A02B-0319-K137

10.4”LCD A02B-0319-K136

7/27/2019 Add_info_B-64305EN_03



TITLE

DRAW. NO B-64305EN/03-02

SHEET




CUST

1) 10.4'' LCD unit

The reverse side of the protection cover has a peel-off sheet. As is shown in a figure below, cut off the right and left sides of the peel-off sheet of theprotection cover, and peel off the hatching part. Be careful not to cut the protection cover.

Part above concave

of screen

Cut line of peel-off sheet

concaveDETAIL

<1> Fit the protection cover to the front of the LCD unit, locate it on the center of the display.Make sure that the concave part of the protection cover does not overlap with theornamental frame of the LCD unit.

<2> Temporarily fix the upside of the protection cover.<3> Pick up the under side of the protection cover, peel off the sheet from the upside slowly.

<1> <2>

<3>

<2>

protectioncover

peel-off sheet

7/27/2019 Add_info_B-64305EN_03



TITLE

DRAW. NO B-64305EN/03-02

SHEET




CUST

After positioning, attach the protection cover while pushing out air between the display andprotection cover toward the under side. This makes it possible to attach the protection cover tidily. After the protection cover is positioned completely, press it firmly while scrubbing thedouble sided adhesive tape part. Scrubbing the cover little by little with your fingers enhancesadhesion of the cover.

double sided adhesive tape (hatching part)

expel air toward the under side

7/27/2019 Add_info_B-64305EN_03



TITLE

DRAW. NO B-64305EN/03-02

SHEET




CUST

2) 8.4'' horizontal LCD/MDI unit

The reverse side of the protection cover has a peel-off sheet. As is shown in a figure below, cut off the up and down sides of the peel-off sheet of theprotection cover, and peel off the hatching part. Be careful not to cut the protection cover.

Part on the leftside of concaveof screen


concave

DETAIL


<2> Temporarily fix the left side of the protection cover.<3> Pick up the right side of the protection cover, peel off the sheet from the left side slowly.

<1>

<2>

<3>

<2>

protection cover

peel-off sheet

7/27/2019 Add_info_B-64305EN_03



TITLE

DRAW. NO B-64305EN/03-02

SHEET




CUST

After positioning, attach the protection cover while pushing out air between the display andprotection cover toward the right side. This makes it possible to attach the protection cover tidily. After the protection cover is positioned completely, press it firmly while scrubbing the doublesided adhesive tape part. Scrubbing the cover little by little with your fingers enhancesadhesion of the protection cover.

expel air toward

the right side

double sided adhesive tape(hatching part)

7/27/2019 Add_info_B-64305EN_03



TITLE

DRAW. NO B-64305EN/03-02

SHEET




CUST

3) 8.4'' vertical LCD/MDI unit

The reverse side of the protection cover has a peel-off sheet. As is shown in a figure below, cut off the right and left sides of the peel-off sheet of theprotection cover, and peel off the hatching part. Be careful not to cut the protection cover.

Part above concaveof screen


concaveDETAIL


<2> Temporarily fix the upside of the protection cover.<3> Pick up the under side of the protection cover, peel off the sheet from the upside slowly.

<1>

<2>

<3>

<2>

protectioncover

peel-off sheet

7/27/2019 Add_info_B-64305EN_03



TITLE

DRAW. NO B-64305EN/03-02

SHEET




CUST

After positioning, attach the protection cover while pushing out air between the display andprotection cover toward the under side. This makes it possible to attach the protection cover tidily. After the protection cover is positioned completely, press it firmly while scrubbing thedouble sided adhesive tape part. Scrubbing the cover little by little with your fingers enhancesadhesion of the cover.

expel air toward

the under side

double sided adhesive tape

(hatching part)

7/27/2019 Add_info_B-64305EN_03


Drawing No. B-64305EN/03-03

CUST.

01 2011/3/15 New issueOtsuki

Title Addition of the specidication of the FROM/SRAM module

Edit. Date Designer Description SHEET 1 / 3

FANUC Series 0i-MODEL DFANUC Series 0i Mate-MODEL DMAINTENANCE MANUAL Addition of the specification of the FROM/SRAM module


NameFANUC Series 0i-MODEL DFANUC Series 0i Mate-MODEL DMAINTENANCE MANUAL

Spec. No./ Version

B-64305EN/03

2. Summary of change

Group Name / OutlineNew, Add.,

Correct, Del. Applicable

Date

BasicFunction

OptionalFunction

Unit

MaintenanceParts

Addition of the specification of the FROM/SRAM module Add At once

Notice

Correction

Another

7/27/2019 Add_info_B-64305EN_03



CUST.

Title

Edit. Date Designer Description SHEET 2 / 3

We add the specification of the FROM/SRAM module in the P.C.B. list at the following paragraph.

2.4.1 Main Board

- FROM/SRAM module mounting location (P.75)

2.5.4 Printed Circuit Boards (P.80)

3.4 CONFIGURATION OF PRINTED CIRCUIT BOARD CONNECTORS AND CARDS

- Mounting positions of cards and DIMM modules (P.101)

3.5.2 List of Printed Circuit Boards (P.106)

2.4.1 Main Board

- FROM/SRAM module mounting location (P.75)

No. Name Specification Function Remarks

FROM/SRAMmodule A1

A20B-3900-0242 A20B-3900-0286

FROM 64MBSRAM 1MB

FROM/SRAMmodule B1

A20B-3900-0240 A20B-3900-0280

FROM 128MBSRAM 1MB

①

FROM/SRAMmodule B2

A20B-3900-0241 A20B-3900-0281

FROM 128MBSRAM 2MB

The FROM stores variouscontrol software programs,user software programs, andso forth.The SRAM is a battery-backedmemory module.

2.5.4 Printed Circuit Boards (P.80)

Name Drawing No. ID Remarks

A20B-3900-0242FROM: E3SRAM: 03

FROM/SRAM module A1(FROM 64MB, SRAM 1MB)

A20B-3900-0286FROM: C3SRAM: 03

A20B-3900-0240FROM: E4SRAM: 03

FROM/SRAM module B1(FROM 128MB, SRAM 1MB)

A20B-3900-0280FROM: C4SRAM: 03

A20B-3900-0241FROM: E4SRAM: 04


A20B-3900-0281FROM: C4

SRAM: 04

A20B-3900-024x: Old specification A20B-3900-028x: New specification

The new specification is notcompatible with the old one.

3.4 CONFIGURATION OF PRINTED CIRCUIT BOARD CONNECTORS AND CARDS- Mounting positions of cards and DIMM modules (P.101)

No. Item Ordering code Function Remarks

FROM/SRAMmodule A1

A20B-3900-0242 A20B-3900-0286

FROM 64MBSRAM 1MB

FROM/SRAMmodule B1

A20B-3900-0240 A20B-3900-0280

FROM 128MBSRAM 1MB

(3)

FROM/SRAMmodule B2

A20B-3900-0241 A20B-3900-0281

FROM 128MBSRAM 2MB

The FROM stores variouscontrol software programs,user software programs, andso forth.The SRAM is a battery-backedmemory module.

7/27/2019 Add_info_B-64305EN_03



CUST.

Title

3.5.2 List of Printed Circuit Boards (P.106)

Item Ordering code ID Remarks

A20B-3900-0242FROM: E3SRAM: 03

FROM/SRAM module A1(FROM 64MB, SRAM 1MB)

A20B-3900-0286FROM: C3SRAM: 03

A20B-3900-0240FROM: E4SRAM: 03


A20B-3900-0280

FROM: C4

SRAM: 03

A20B-3900-0241FROM: E4SRAM: 04


A20B-3900-0281FROM: C4SRAM: 04

A20B-3900-024x: Old specification A20B-3900-028x: New specification

The new specification is notcompatible with the old one.

add_info_b-64305en_03

Documents