addendum no. cc-2 architecture engineering … · “e. cs-4: single compartment, counter-mounting,...

ADDENDUM NO. CC-2 CC-2 - 1

ADDENDUM NO. CC-2 PLATTVIEW JR & SR HIGH SCHOOL RENOVATIONS SPRINGFIELD PLATTEVIEW COMMUNITY SCHOOLS SPRINGFIELD, NEBRASKA DLR GROUP PROJECT NO. 10-13125-30 COMBINED CONTRACT September 20, 2017 NOTICE TO BIDDERS: Amend the Project Manual and Drawings to the above referenced project as follows:

PROJECT MANUAL ITEM NO. 1 SECTION 004113 BID FORM

A. Delete Bid Form and substitute new Bid Form as shown on Attachment No. 1. ITEM NO. 2 SECTION 074113.16 STANDING-SEAM METAL ROOF PANELS

A. 1.2.A. Add the following: “and metal wall panels.”

B. 2.2. Add the following: “AND METAL WALL PANELS”

ITEM NO. 3 SECTION 123553.15 PLASTIC-LAMINATED-CLAD CASEWORK AND LABORATORY

CASEWORK

A. 2.7.C Add paragraph.

C. Cork for direct, frameless application at millwork (Tack Surface – TS-1):

1. Manufacturers: Subject to compliance with requirements, provide products by the following:

a. Forbo Flooring Systems.

2. Linoleum Resilient Cork Sheet, Bulletin Board: Seamless, homogeneous, self-sealing sheet consisting of granulated cork, linseed oil, resin binders, and dry pigments that are mixed and calendared onto a natural burlap backing; with integral color throughout with surface-burning characteristics indicated.

a. Color: As selected from manufacturer’s full range. b. Thickness: 1/4 inch (6 mm). c. ASTM E-84 (Fuel Contribution): Class B. d. NFPA 253 (Critical Radiant Flux): Class II. e. Adhesive for Installation to Wall and Millwork Surfaces: Manufacturer’s standard adhesive applied with notch trowel at manufacturer’s recommended

spreading rate.

B. Delete Paragraph 2.11.A in its entirety.

C. Delete Paragraph 2.11.B in its entirety.

Architecture Engineering Planning Interiors

6457 Frances Street, Suite 200 Omaha, NE 68106

tel 402/393-4100 fax 402/393-8747

[email protected]

www.dlrgroup.com

PLATTVIEW JR & SR HIGH SCHOOL RENOVATIONS 10-13125-30 SPRINGFIELD PLATTEVIEW COMMUNITY SCHOOLS SPRINGFIELD, NEBRASKA


D. Paragraph 2.11.C, add the following:

1. “Troughs to be 2 inches deep.”

E. Subparagraph 2.13.B.1, add the following:

1. “In Room F223.”

F. Delete Subparagraph 2.13.B.2 in its entirety.

ITEM NO. 4 SECTION 223400 FUEL FIRED, DOMESTIC WATER HEATERS

A. Subparagraph 2.1.A.1 add the following: “c. Lochinvar”

B. Subparagraph 2.1.A.2 add the following: “c Lochinvar”

C. Subparagraph 2.1.A.3 add the following: g. Bell & Gosset

ITEM NO. 5 SECTION 224000 PLUMBING FIXTURES

A. Subparagraph 2.1.A.5 add the following manufacturer: “5. Sloan.”

B. Paragraph 2.12, add the following:

“E. CS-4: Single compartment, counter-mounting, stainless-steel commercial sink.

1. Overall Dimensions: 22 inches x 19-1/2 inches x 7-5/8-inch. 2. Metal Thickness: 18 gage. 3. Each Compartment:

a. Dimensions: 18 inches x 14 inches x 7-5/8-inch. b. Drains: Provide with Elkay LK-2219 Type 304 stainless steel body an removable conical basket strainer with metal ball bearing locking stem and rubber stopper with NPS 1-1/2 (DN 40) tailpiece.

1) Location: Off-Centered Rear.

c. Sink undercoating to dampen sound and prevent condensation.”

ITEM NO. 6 SECTION 232123 HYDRONIC PUMPS

A. Paragraph 2.1.A. add the following: “6. Armstrong”



ITEM NO. 7 SECTION 233423 POWER VENTILATORS A. Paragraph 2.1.A. add the following: “4. Twin city Fan Company”



DRAWINGS ITEM NO. 6 DRAWING A1.2F FLOOR PLAN, MAIN LEVEL – AREA F

A. Modify Drawing as shown per Attachment A1.2F-1.

ITEM NO. 7 DRAWING A9.1 DOOR AND FRAME SCHEDULE

A. Door F103A add Frame Type “1” and Door Type “A”.

B. Door F216 Janitor, delete hardware set “26” and replace with hardware set “20”. ITEM NO. 8 DRAWING A11.1 CASEWORK ELEVATIONS

A. Modify Drawing as shown per Attachment A11.1-1.

ITEM NO. 9 DRAWING A11.2 CASEWORK ELEVATIONS

A. Modify Drawing as shown on Attachment A11.2-1.

ITEM NO. 10 DRAWING MD1.1F HVAC DEMOLITION PLAN, LOWER LEVEL – AREA F

A. Modify Drawing as shown on Attachment MD1.1F-1.

ITEM NO. 11 DRAWING MD1.2F HVAC DEMOLITION PLAN, MAIN LEVEL – AREA F

A. Modify Drawing as shown on Attachment MD1.2F.

ITEM NO. 12 DRAWING M1.2F HVAC PLAN, MAIN LEVEL – AREA F

A. Modify Drawing as shown on Attachment M1.2F-1.

ITEM NO. 13 DRAWING M2.1F HVAC PIPING PLAN, LOWER LEVEL – AREA F


ITEM NO. 14 DRAWING M2.2F HVAC PIPING PLAN, MAIN LEVEL – AREA F


ITEM NO. 15 DRAWING M4.1 MECHANICAL DETAILS

A. Modify detail 4 per as shown on Attachment M4.1-1.

ITEM NO. 16 DRAWING M4.2 MECHANICAL DETAILS

A. Modify details 5 & 9 as shown on Attachment M4.2-1.

ITEM NO. 17 DRAWING M5.1 MECHANICAL SCHEDULES

A. Modify Drawing as shown on Attachment M5.1-1.



ITEM NO. 18 DRAWING M5.2 MECHANICAL SCHEDULES

A. Modify Drawing as shown on Attachment M5.2-1.

ITEM NO. 19 DRAWING P0.1C UNDERGROUND PLUMBING PLAN, MAIN LEVEL – AREA C

A. Modify Drawing as shown on Attachment P0.1C-1.

ITEM NO. 20 DRAWING P1.2F PLUMBING PLAN, MAIN LEVEL – AREA F

A. Modify Drawing as shown on Attachment P1.2F-1.

ITEM NO. 21 DRAWING P2.1 PLUMBING LARGE SCALE PLANS & RISER DIAGRAMS

A. Modify drawing as shown on Attachment P2.1-1.

ITEM NO. 22 DRAWING P2.2 PLUMBING LARGE SCALE PLANS

A. Modify Drawing as shown on Attachment P2.2-1.

ITEM NO. 23 DRAWING P3.1 WASTE AND VENT RISER DIAGRAMS

A. Modify Drawing as shown on Attachment P3.1-1.

ITEM NO. 24 DRAWINGS FP1.1F, FP1.2C, AND FP1.2F

A. Remove note 4 from Fire Suppression Legend Notes on Attachments FP1.1F-1, FP1.2C-1, and FP1.2F-1.

ITEM NO. 25 DRAWING E7.1 ELECTRICAL LIGHTING SCHEDULES

A. Modify light fixture schedule type P3 on Drawing as shown on Attachment E7.1-1.

END OF ADDENDUM

PLATTEVIEW JR HIGH & HIGH SCHOOL RENOVATIONS 10-13125-30 SPRINGFIELD PLATTEVIEW COMMUNITY SCHOOLS BID SET SPRINGFIELD, NEBRASKA

BID FORM 004113 - 1

DOCUMENT 004113 - BID FORM COMBINED CONSTRUCTION Platteview Jr High & High School Renovations Springfield Platteview Community Schools 14801 South 108th Street Springfield, Nebraska 58059 DLR Group Project No. 10-13125-30 Issue Date: August 29, 2017 Bid of_______________________________________________________________________________, /_/ a corporation organized and existing under the laws of the State of _______________________; _ /_/ a partnership consisting of _____________________________________________ , partners; or _ /_/ a sole proprietor; hereinafter called the Bidder. To: Brett Richards, Superintendent Springfield Platteview Community Schools 14801 South 108th Street Springfield, Nebraska 68059 The undersigned acknowledges that he has received and familiarized himself with the following: Project Manual: Divisions and Sections as listed in the Table of Contents Drawings: As listed on the Index of Drawings Sheet Addenda: No. _________________ Dated ________________

No. _________________ Dated ________________

No. _________________ Dated ________________

The undersigned further acknowledges that he has visited the site and familiarized himself with local conditions affecting the cost of the Work at the place where the Work is to be done.

Attachment No. 1 for Addendum CC-2, Dated September 20, 2017


BID FORM 004113 - 2

In submitting this Bid, the undersigned agrees:

1. To furnish all material, labor, tools, expendable equipment, and all utility and transportation services necessary to provide and complete, in a workmanlike manner, all of the Work required for the Combined Construction, including General Construction, Mechanical Work, Electrical Work, and Elevator Work, in accord with the Bidding Documents prepared by DLR Group inc., for the consideration hereinafter set forth.

2. To hold his Bid open for thirty (30) days after the receipt of Bids and to accept the provisions of the

Instructions to Bidders regarding disposition of Bid Security. 3. To enter into and execute a Contract if awarded on the basis of this Bid, to furnish a Performance Bond and a Labor and Material Payment Bond in accord with the General Conditions and General Requirements of this Contract, and to deliver executed Owner-Contractor Agreements and Bonds to the Architect-Engineer within ten (10) days after notification of award, for submittal to the Owner for his approval and acceptance. 4. To substantially complete the Work as specified in Division 01 Section “Summary.” LUMP SUM BASE BID: The undersigned hereby proposes and agrees to provide the foregoing for the Lump Sum of ____________________________________________________________dollars ($__________________). (Amount shall be shown in both words and figures. In case of discrepancy, the amount shown in words will govern.)

PRIME SUBCONTRACTORS: The undersigned proposes the following Prime Subcontractors: Mechanical Work: _________________________________________________________________ Electrical Work: ___________________________________________________________________ ALTERNATES: The above Lump Sum Base Bid may be modified in accord with the following Alternates as may be accepted by the Owner. Provide a bid for all Alternates. If there is no cost to the work described, indicate so by writing zero, $0. If you do not provide a bid price, indicate so by writing, “No Bid.” ALTERNATE NO. CC-1. All work in the renovation of the High School Locker Room “Area C”. If this Alternate is accepted, add to the Lump Sum Base Bid the sum of ________________________________________________________________ dollars ($______________).


BID FORM 004113 - 3

ALTERNATE NO. CC-2. Pre-manufacture metal canopy system. If this Alternate is accepted, add to the Lump Sum Base Bid the sum of _______________________________________________________________ dollars ($______________). ALTERNATE NO. CC-3. Add acoustical baffles. If this Alternate is accepted, add to the Lump Sum Base Bid the sum of ________________________________________________________________ dollars ($______________). UNIT PRICE BIDS: The undersigned hereby proposes and agrees to provide the foregoing in relation to the following Work. The quantities specified may be modified by a Change Order in accord with the following Unit Prices: 1. Furnish and install the Repair of Gypsum Roof Deck as specified:

Add ($ ___ __) for each square foot added

2. Furnish and install the Replacement of Additional Steel Roof Deck as specified:

Add ($ _____) for each square foot added

ALTERNATES AND UNIT PRICES: The Lump Sum Base Bid may be modified in accord with the Alternates and Unit Prices as proposed by the undersigned on his completed Bid Forms for the respective projects. The undersigned has attached the required Bid Security and other items required in the Instructions to Bidders. The undersigned has attached the required Bid Security. In submitting this Bid, it is understood that the right to reject any and all Bids and to waive irregularities in the bidding has been reserved by the Owner. Dated this _____________________________________ day of ______________________ _____, 20_____ ___________________________________________________ Name of Bidder


BID FORM 004113 - 4

___________________________________________________ Address of Bidder ___________________________________________________ Authorized Officer ___________________________________________________ Area Code/Telephone Number

END OF DOCUMENT

UP

DN

UP

UPUP

A5.132

A5.1

A5.1

A5.1

12

52

42

A B C

D

E F G H J K

1

2

3

4 5

6

7

8

9

10

11

GYMNASIUM

F244

KITCHEN

F239

STORAGE

F240

VEST

F247

OFFICE

F234

STORAGE

F245

CLASSROOM

F233

GIRLS

F243

BOYS

F242

ELECTRICAL

F238

COORIDOR

F241

VEST

F201

EARLYEDUCATION

F202

EARLYEDUCATION

F203BOYS

F204

GIRLS

F205

BOYS

F213

GIRLS

F214

PRINCIPAL

F207

NURSE

F209

WORK ROOM

F211

GUIDANCE

F208

CLASSROOM

F222

CLASSROOM

F221

SPECIAL ED

F230

JANITOR

F216

CLASSROOM

F228

TEACHERSLOUNGE

F220

WOMENS

F217

MENS

F218

CLASSROOM

F229

SCIENCE

F223

CONFERENCEROOM

F225

ELEC

F224

TOILET

F210

SMOKECURTAIN

LEARNINGCOMMONS

F232

ALCOVE

F236

RECEPTION

F206

CORRIDOR

F215

COORIDOR

F227

CORRIDOR

F212

CORRIDOR

F219

F241

F209

F208

F222

F216

F225

F228 F229

F221

F217

F223

F233

F230

F210

F207

F218

F220

F213

F214

F245

F227

F234

F242 F243

F239B

F244

F239C

F240

F247

F239A

F237

F239

F202

F212

A2.1

23

A2.1

25

OFFICE

F231

F203

8' MBD 8' MMBD

8' MMBD

8' M

MB

D

8' MBD

8' MMBD

4' MBD

8' MBD

8' M

BD

8' M

MB

D

8' M

BD

LIFT

4' MBD

4' MBD

JANITOR

F237

A11.111

8' M

BD

12

13

TV(NIC)

16/ A

11.1

A11.1 21

4' MBD4' TBD

A11.134

25

14

A11.1

24

SMARTBOARD(OFCI)

8' M

BD

8' MBD

8' MBD

MOBILE MARKERBOARD(NIC)

HO

OD

STORAGE

F226

8' M

BD

4' MBD

4' M

BD

4' M

BD

4' M

BD

4' M

BD

4' M

BD

A11.2

12

A11.133

A11.122

A11.1 23

A11.1

42

43

A11.1 45

44

46

A11.1

52

51F223A

F224

F226 F231

F238

F233A

41/ A

11.1

19' - 6"

TV(NIC)

6' - 6" 22' - 10 5/8" 22' - 10 3/8" 6' - 5" 27' - 9 1/4"

OFFICE

F235

F235

F244A

EWC-2 EWC-1

F

E

E

F

F

G

G

H

J

K

F202A

F201

14/ A11.2

16/ A11.2

LABOVE

1' - 0 3/8" 9' - 0"

6' -

8"

5' -

4"

5' -

0"

10' -

6"

8' - 9" 12' - 0"

3' - 4"

27' -

9 1

/4"

7' -

8 7

/8"

7' -

4"

7' -

5"

28' -

0"

40' -

4"

32' -

8"

8' -

6"

12' -

8"

9' - 0 1/4" 18' - 9"

25' -

11

1/8"

F219

F232

26/ A11.1

26/ A11.126/ A11.1

26/ A11.1

26/ A11.1

13/ A11.2

56

A7.1

9' -

0"

MECHANICAL

F246

F246

A8.1

36

A8.1

46

A8.1

31

TYP. FIN. FL.112' - 0"

TYP. FIN. FL.108' - 4"

TYP. FIN. FL.108' - 4"

TYP. FIN. FL.108' - 4"

TYP. FIN. FL.112' - 0"

25

A7.1

2' - 10" 8' - 0"

2' -

10"

2' -

10"

1' - 6"4' T

BD

6' M

BD

4' T

BD

FEC/B

FEC

FEC

FE

FEC

26' -

6 5

/16"

51

A7.1

53

A7.1

CO

PIE

R(N

IC)

C

C

CC

C

C

C

C

C

C

C

FD

FD

FD

FD

22' - 5" 1' - 1" 22' - 3"

1' -

10"

EWC-2

ICE

(NIC

)R

EF

(NIC

)

VE

ND

(NIC

)

3' -

8"

3' - 4"

A2.1

41

POWER DOOROPERATOR

POWER DOOROPERATOR

DOOR OPERATORSWITCH

POWER DOOROPERATOR

DOOR OPERATORSWITCH

A-1 A A-1 A-1 A-1

A-1A-1

A A A A A A A A A A A A A A A A A A A A A A

A A A A A A A A A A A A A A A A A A A A A A A A A

A8.1

32

FD

NEW STRUCTURALSTOOP - SEE STRUCTURE

DOOR OPERATORSWITCH

40' - 7 1/8"

21

A11.2

WOOD BENCH PROVIDEDBY ATHLETIC LOCKERMANUFACTURER, TYP

6' - 10"6' - 10"

A12.136

A2.1

43

A2.1

45

STORAGE

F248

F1F1

F1 M1

F

C

F

F

F1

F1

F1

NNF1

F1

J

J

F1

F1

J

J

F1

F1

F1

F1

F1

F1

A1

F1 F1

A

A1

E1

E1

E1

E1

E1

E1

D

A1

E1

E

B

BB

B

B

E

B1

F1

B1

B

E

B

B

B

A

A

M1

F1

F1

CG-1

CG

CG-1

CG

CG

CG

CG

ABOVE

F236

N

N

CG

CG

CG CG CG

M1

K

4' -

0"

56

A10.2

TYP

ALIGN WITH WALLWITH WINDOW JAMB

GOGGLESCABINET

2' - 6"

2' -

6"

A

A

A10.1

15TYP

9' -

4"

25/ A11.2

26/ A

11.2

1 REMOVE WALL IN ITS ENTIRETY.

REMOVE DOOR, FRAME AND HARWARE IN ITS ENTIRETY.

REMOVE CONCRETE RISERS IN HATCHED AREA FOR NEW SLAB ONGRADE CONCRETE FLOOR.

SAWCUT AND REMOVE FLOOR IN HATCHED AREA FOR ELECTRICALCONDUIT - COORDINATE WITH ELECTRICAL. PATCH AND REPAIRCONCRETE SLAB TO MATCH ADJACENT ELEVATIONS.

SAWCUT AND REMOVE FLOOR IN HATCHED AREA FOR PLUMBINGWORK - COORDINATE WITH MECHANICAL. PATCH AND REPAIRCONCRETE SLAB TO MATCH ADJACENT ELEVATIONS.

SAWCUT AND REMOVE PORTION OF WALL TO THE DIMENSIONSINDICATED FOR NEW OPENING. PATCH AND REPAIR REMAININGPORTION OF WALL TO MATCH ADJACENT SURFACES. PATCH ANDREPAIR FLOOR WITH SELF-LEVELING COMPOUND TO MATCHADJACENT FLOOR ELEVATION.

REMOVE PLUMBING FIXTURE IN ITS ENTIRETY- COORDINATEWITH MECHANICAL.

REMOVE EXISTING TOILET PARTION AND ASSOCIATED ACCESSORIESIN ITS ENTIRETY.

REMOVE MIRRORS, TOILET TISSUE DISPENSERS, SANITARYNAPKIN DISPOSALS AND SOAP DISPENSERS IN THEIR ENITRETY.PATCH AND REPAIR WALLS AS NEEDED.

REMOVE FLOOR TILE AND WALL TILE IN ITS ENTIRETY, PATCHAND REPAIR WALL AS NEEDED. PATCH, REPAIR AND PREPAREFLOOR FOR NEW FLOORING.

REMOVE WINDOW IN ITS ENTIRETY.

REMOVE CASEWORK IN ITS ENTIRETY.

REMOVE LOCKERS IN THEIR ENTIRETY.

REMOVE EXISTING CARPET.

REMOVE VCT FLOORING.

GRIND/MECHANICALLY ABRADE CONCRETE FLOOR TO REMOVEADHESIVIES/COATINGS FOR INSTALLATION OF NEW FLOORING.

REMOVE EXISTING RAMP, HANDRAILS RAILS IN THEIR ENTIRETY.

REMOVE EXISTING HANDRAILS.

REMOVE EXISTING PIT IN ITS ENTIRETY. PREPARE FOR NEWCONCRETE SLAB ON GRADE FLOOR. MATCH ADJACENT FLOORELEVATIONS.

REMOVE PARTITION WALL AND ASSOCIATED ACCESSORIESIN ITS ENTIRETY.

REMOVE EXISTING TACKWALL ON EXTERIOR WALLS.

REMOVE AND SALVAGE CARPET TILE AND RETURN TO OWNER.

SAWCUT AND REMOVE PORTION OF WALL TO THE DIMENSIONSINDICATED STARTING AT 3'-4" AFF UP TO STRUCTURE FOR NEW OPENING.

REMOVE EXISTING ASPHALT FOR NEW STRUCTURAL STOOP.

REMOVE EXISTING CONCRETE FOR NEW STURUCTURAL STOOP TOPPING.

REMOVE EXISTING STAIRS IN ITS ENTIRETY.

BLEACHERS TO BE REMOVED BY OWNER.

REMOVE EXISTING LADDER.

REMOVE BASE CASEWORK. UPPER CASEWORK TO REMAIN.

REMOVE AND SALVAGE FACE BRICK, TO BE USED FOR INFILL WHERESHOWN ON EXTERIOR ELEVATIONS.

REMOVE EXISTING CONCRETE CURB IN ITS ENTIRETY.

SAWCUT AND REMOVE HATCHED PORTION OF CONCRETE.

REMOVE SECTION OF STEEL TUBE CURB TO MAKE LEVEL WITH EXISTINGFINISH FLOOR FOR INSTALLATION OF NEW LIFT. COORDINATE SIZE OF OPENINGWITH THE SIZE OF LIFT BEING INSTALLED BY LIFT MANUFACTURER.

REMOVE EXISTING CARPET AND ADHESIVE ON STEEL TUBE CURB. PREPARESURFACE FOR NEW PRIMER AND PAINT.

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

Arc

hite

ctu

re E

ngin

eering

P

lan

nin

g In

teriors

©

,

DL

R G

rou

p inc., a

Ne

bra

ska

co

rpo

ratio

n, A

LL

RIG

HT

S R

ES

ER

VE

D

KEY PLAN

A

NO

RT

H

Rev

isio

ns

B

C

D

E

F

9/2

0/2

017 1

:46:4

8 P

M

C:\R

evit\1

0-1

3125-3

0_A

R_2016_C

entr

al_

jlim

bach.r

vt

10-1

3125-3

0

8/2

9/2

017

PLA

TT

EV

IEW

JR

HIG

H &

HIG

H S

CH

OO

L R

EN

OV

AT

ION

S

FLO

OR

PLA

N, M

AIN

LE

VE

L -

AR

EA

FA1.2F

20

17

SP

RIN

GF

IELD

PLA

TT

EV

IEW

CO

MM

UN

ITY

SC

HO

OLS

NORTHSCALE: 1/8" = 1'-0"

FLOOR PLAN, MAIN LEVEL - AREA F

CC

-29/

21/1

7A

DD

EN

DU

M C

C-2

CC-2CC-2

MICROWAVE(NIC)

MICROWAVE(NIC)

FRIDGE(NIC)

VENDING(NIC) ICE

(NIC)

COUNTER TOP: PL-2CABINETS: PL-1

3' - 0" 3' - 0" 3' - 3"

3' - 0" 3' - 0" 1' - 9" 3' - 0"

W2052 W9330 W2052

B2542 B1050

9' - 3"

2' -

10"

1' -

8"

2' -

6"

7' -

0"

KNEESPACE

D1211 B2360

10' - 9"

ELEC DEVICE- SEE ELECTRICAL

SINK/FAUCETSEE MECHANICAL

PTDSDHC


3' - 0" 3' - 0" 3' - 0" 3' - 0" 3' - 0"

15' - 0"

2' -

6"

1' -

8"

2' -

10"

W2052 W2052 W2052 W2052 W2052

B2360 D1223 D1223 D1223 D1223 B2360

3' - 0"

FILLER PANEL

3' - 0" 3' - 3" 3' - 3" 3' - 3"

FILLER PANEL

3' - 0"

18' - 10 1/2"



3' - 0" 2' - 0"

5' - 0"

2' -

6"

1' -

0"

8"2'

- 1

0"

7' -

0"

W2052 H2051

B2360 D1211

2' - 9" 1' - 0"

3' - 9"


KNEESPACE

COUNTER TOP: PL-2COUNTER TOP: SS-1CABINETS: PL-1

3' - 0" 2' - 6" 2' - 0" 1' - 4" 1' - 3" 1' - 3" 4' - 3 1/2" 1' - 4" 1' - 4" 1' - 4" 3' - 0" 1' - 6" 2' - 3"

2' -

10"

1' -

8"

2' -

6"

D1223 D1223 D1211 D2800 D3320 D2800 D2800 D2800 D1223 D1211 B1050

2' -

6"

7 1/

2"4

1/2"

7' -

0" SS-1 ELEC DEVICE

- SEE ELECTRICALLOCKS, TYP

SS-1PL-2

PL-2

PL-1

CC-2

COUNTER TOP: PL-2VERTICAL: PL-1

2' -

6"

24

A11.2


PL-1

KNEESPACE


UNDERCOUNTERREFR (NIC)

2' - 6" 3' - 0"

10' - 1 1/8"

B2542 D1223

4' -

2"

2' -

10"

2' -

6"

2' -

0"

2' -

6"

7' -

0"

1' - 3" 3' - 0" 3' - 0" 2' - 6"

9' - 9"

H2050 W2052 W2052 W2052


LOCKS, TYP


PTDSD HC

PL-1 COUNTER TOP: PL-2CABINETS: PL-1

2' -

6"

1' -

0"

3' -

6"

7' -

0"

2' -

6"

2' -

0"

2' -

6"

3' - 3" 3' - 3" 1' - 0"

7' - 6"

W2052 W2052 H2051



3' - 0" 1' - 4" 1' - 4"

2' -

10"

4' -

2"

7' -

0"

5' - 8"

T2586 D2800 D2800

LOCKS, TYP


KNEESPACE

COUNTER TOP: PL-2CABINETS: PL-1VERTICAL: PL-1

2' -

6"

1' -

0"

3' -

6"

2' - 6" 2' - 9"

5' - 3"

D3320 D1223

23

A11.2LOCKS, TYP


PL-1

SS-1

PL-2TS-1

SUPPORTBRACKET


3' - 0"

FILLER PANEL

3' - 0"

FILLER PANEL

3' - 0"

9' - 2 1/16"

D1223 B2360B2360

2' - 6" 2' - 6" 2' - 6"

7' - 6"

2' -

6"

1' -

8"

2' -

10"

7' -

0"

W2052 W2052 W2052


3' - 0" 3' - 0" 3' - 0" 3' - 0"

12' - 0"

4' -

2"

2' -

10"

7' -

0"

T2586 D1223 D1223 D1223

LOCKS, TYPELEC DEVICE- SEE ELECTRICAL


2' - 9" 1' - 9" 1' - 0" 3' - 0"

8' - 6"

2' -

10"

1' -

8"

2' -

6"

7' -

0"

2' - 9" 2' - 9" 3' - 0"

8' - 6"

D1223 D1223 T2586

H2050W2051W2052



2' - 6"

FILLER PANEL

3' - 3" 3' - 3" 3' - 0"

4' - 6" 3' - 0"

T2102 D1223 D1223 B2360

H9210 W2052

12' - 1 1/8"

2' -

10"

1' -

8"

2' -

6"

7' -

0"

LOCKS, TYP


CABINETS: PL-1

1' - 9" 1' - 9" 1' - 9" 1' - 9" 1' - 9"

8' - 9"

T2050 T2050 T2050 T2050 T2050

7' -

0"

LOCKS, TYP

CABINETS: PL-1

1' - 9" 1' - 9" 1' - 9" 1' - 9" 1' - 9" 1' - 9" 1' - 9"

T2050 T2050 T2050 T2050 T2050 T2050 T2050

7' -

8"

4' - 0"

FUMEHOOD

KNEE SPACE


CEILING CLOSURE BYHOOD MANUFACTURER

COUNTER TOP: BLACK EPOXYCABINETS: PL-1

1' - 6" 3' - 0" 3' - 0" 3' - 0" 3' - 0" 2' - 6"

W2050 W2052 W2052 W2052 W2052 W2341

16' - 0"

1' - 6" 3' - 0" 3' - 0" 3' - 0" 1' - 9" 3' - 9"

16' - 0"

D1120 B2542 D1223 D1223 D1120 D1139

1' -

6"

1' -

0"

1' -

8"

2' -

10"

7' -

0"

PEG BOARD DRYING RACK

LOCKS, TYP


SINK/FAUCETBY CASEWORK MFR

HC


2' - 9" 1' - 0"

3' - 9"

3' - 0"

D1223

2' -

10"

8"1'

- 0

"2'

- 6

"

7' -

0"

W2052 H2051

VENTED CHEMICALSTORAGE CABINETS

LOCKS, TYP


GWB CEILING ATTOP OF CASEWORK


2' - 0" 3' - 0" 2' - 0" 2' - 0"

9' - 0"

2' - 0" 3' - 0" 2' - 0" 3' - 9"

10' - 9"

D1120 B2522 D1120 D1139

W2050 W2052 W2051 W2051

1' -

6"

1' -

0"

1' -

8"

2' -

10"

7' -

0" ELEC DEVICE

- SEE ELECTRICAL

LOCKS, TYP



3' - 0" 3' - 0" 3' - 0" 3' - 0" 3' - 0" 3' - 0"

18' - 0"

3' - 3" 3' - 3" 3' - 3" 3' - 3" 3' - 3"

16' - 3"

2' -

10"

1' -

8"

2' -

6"

7' -

0"

W2052 W2052 W2052 W2052 W2052 W2052

D1223 D1223 D1223 D1223 D1223

LOCKS, TYP ELEC DEVICE- SEE ELECTRICAL


2' - 0" 2' - 0" 3' - 0" 2' - 0"

9' - 0"

2' -

10"

1' -

8"

1' -

0"

1' -

6"

7' -

0"

3' - 9" 2' - 0" 3' - 0" 2' - 0"

10' - 9"

D1211 B2522 D1211D1138

W2050 W2050 W2052 W2051


LOCKS, TYP


PTD SD


EYEWASH/SHOWER

2' - 6" 2' - 6"

5' - 0"

W2052 W2052

2' - 9" 1' - 6"

4' - 3"

D1223 D1120

2' -

10"

1' -

8"

2' -

6"

7' -

0"ELEC DEVICE

- SEE ELECTRICAL

LOCKS ,TYP


GOGGLE CABINET

2' - 6" 2' - 0" 2' - 0" 3' - 0" 3' - 0" 1' - 6"

14' - 0"

3' - 9" 2' - 9" 3' - 0" 3' - 0" 1' - 6"

14' - 0"

D1138 D1223 D1223 B2522 D1211

W2340 W2050 W2051 W2052 W2052 W2051

2' -

10"

1' -

8"

2' -

6"

7' -

0" ELEC DEVICE

- SEE ELECTRICAL

LOCKS, TYP


PTD SD

1' - 6" 3' - 0" 3' - 0" 3' - 0" 1' - 9" 3' - 9"

COUNTER TOP: CRPL-1CABINETS: PL-1

16' - 0"

1' - 6" 3' - 0" 3' - 0" 3' - 0" 3' - 0" 2' - 6"

16' - 0"

D1120 B2542 D1223 D1223 D1120 D1139

W2050 W2052 W2052 W2052 W2052 W2341


LOCKS, TYP

PEG BOARD DRYING RACK

PTD


SD

HC

COUNTER TOP: CRPL-1CAB1NETS: PL-1

2' - 9" 1' - 0"

3' - 9"

3' - 0"

2' -

10"

8"1'

- 0

"2'

- 6

"

7' -

0"

W2052 H2051

D1223


LOCKS, TYP


3' - 0" 3' - 0" 3' - 0" 3' - 0" 3' - 0" 3' - 0"

18' - 0"

3' - 0" 2' - 6" 2' - 6" 2' - 6" 2' - 6" 3' - 0"

16' - 0"

B2522 D1223 D1223 D1223 D1223 B2522

W2052W2052W2052W2052W2052W2052

2' -

10"

1' -

8"

2' -

6"

7' -

0"ELEC DEVICE

- SEE ELECTRICAL

LOCKS, TYP



SD PTD SD PTD

UNDERCOUNTERREFR (NIC)


2' - 6" 2' - 6" 2' - 3" 2' - 8 1/2"

9' - 11 1/2"

3' - 6" 1' - 9" 2' - 2 1/8" 2' - 8 1/2"

10' - 1 5/8"

2' -

10"

1' -

8"

2' -

6"

7' -

0"

W2340 W2052 W2052

T2632D12111092

LOCKS ,TYP




AQUA TANK(NIC)

3' - 0" 1' - 6"

4' - 6"

W2052 W2051

2' - 0" 3' - 9"

5' - 9"

D1120 D1139

2' -

6"

1' -

8"

2' -

10"

7' -

0"


LOCKS, TYP


3' - 0" 3' - 3" 3' - 3" 3' - 0" 1' - 6"

14' - 0"

3' - 0" 3' - 3" 3' - 3" 3' - 0" 1' - 6"

14' - 0"

2' -

10"

1' -

8"

1' -

0"

1' -

6"

7' -

0"

W2052 W2052 W2052 W2052 W2051

D1223 D1223 D1223 B2522 D1211


LOCKS,TYP


PTD SD

GOGGLE CABINET

CASEWORK AND MILLWORK GENERAL NOTES

A. CASEWORK AND MILLWORK GENERAL NOTES APPLYTO ALL CASEWORK AND MILLWORK SHEETS.

B. CASEWORK SPECIFIED UNDER DIVISION 12,UNLESS NOTED OTHERWISE.

C. BASE AND TALL STORAGE CABINETS: 24 INCHESDEEP, UNLESS NOTED OTHERWISE.

D. WALL CABINETS: 14 INCHES DEEP, UNLESS NOTEDOTHERWISE.

E. TALL STORAGE UNITS TO BE 24 INCHES DEEP,UNLESS NOTED OTHERWISE.

F. PROVIDE ADJUSTABLE SHELVING IN CASEWORK,UNLESS NOTED OTHERWISE.

G. CATALOG NUMBERS SHOWN ON THE ELEVATIONSFOR CASEWORK ARE TMI REFERENCE NUMBERS,UNLESS NOTED OTHERWISE. (M) AFTER THECATALOG NUMBER INDICATES THE CABINET ISSHOWN MODIFIED FROM STANDARD.

H. WHERE ELECTRICAL DEVICES ARE LOCATED INCASEWORK, CASEWORK CONTRACTOR SHALLPROVIDE FINISHED OPENINGS. COORDINATELOCATION AND QUANTITY WITH ELECTRICALCONTRACTOR.

I. PROVIDE JOINT SEALANT AT PERIMETER JOINTSWHERE COUNTERTOPS, BACK AND SIDESPLASHES, CASEWORK, AND MILLWORK ABUTWALLS.

J. FIELD VERIFY DIMENSIONS OF CABINETLOCATIONS IN BUILDING PRIOR TO FABRICATION.

K. PROVIDE LOCKS AT DOORS AND DRAWERS WHEREINDICATED.

L. PROVIDE FINISHED ENDS AT ALL EXPOSED ENDSOF CASEWORK AND MILLWORK.

M. ALL EXPOSED SURFACES IN OPEN SHELVING SHALLBE PLASTIC LAMINATE COVERED.

Arc

hite

ctu

re E

ngin

eering

P

lan

nin

g In

teriors

©

,

DL

R G

rou

p inc., a

Ne

bra

ska

co

rpo

ratio

n, A

LL

RIG

HT

S R

ES

ER

VE

D

Rev

isio

ns

9/2

0/2

017 1

:46:5

8 P

M

C:\R

evit\1

0-1

3125-3

0_A

R_2016_C

entr

al_

jlim

bach.r

vt

10-1

3125-3

0

8/2

9/2

017

PLA

TT

EV

IEW

JR

HIG

H &

HIG

H S

CH

OO

L R

EN

OV

AT

ION

S

CA

SE

WO

RK

ELE

VA

TIO

NS

A11.1

20

17

SP

RIN

GF

IELD

PLA

TT

EV

IEW

CO

MM

UN

ITY

SC

HO

OLS

SCALE: 1/4" = 1'-0"A11.1

11 F220 TEACHERS LOUNGESCALE: 1/4" = 1'-0"A11.1



14 F211 WORK ROOMSCALE: 1/4" = 1'-0"A11.1

16 F206 RECEPTION

SCALE: 1/4" = 1'-0"A11.1

21 F209 NURSESCALE: 1/4" = 1'-0"A11.1

22 F231 OFFICESCALE: 1/4" = 1'-0"A11.1

23 F208 GUIDANCESCALE: 1/4" = 1'-0"A11.1

24 F206 RECEPTIONSCALE: 1/4" = 1'-0"A11.1


26 TYPICAL CLASSROOM

SCALE: 1/4" = 1'-0"A11.1

33 F230 SPECIAL EDSCALE: 1/4" = 1'-0"A11.1


35 F122 STORAGESCALE: 1/4" = 1'-0"A11.1

36 F122 STORAGE

SCALE: 1/4" = 1'-0"A11.1

41 F223 SCIENCESCALE: 1/4" = 1'-0"A11.1

42 F223 SCIENCESCALE: 1/4" = 1'-0"A11.1

43 F223 SCIENCESCALE: 1/4" = 1'-0"A11.1

44 F223 SCIENCESCALE: 1/4" = 1'-0"A11.1

45 F223 SCIENCESCALE: 1/4" = 1'-0"A11.1

46 F223 SCIENCE

SCALE: 1/4" = 1'-0"A11.1

51 F223 SCIENCESCALE: 1/4" = 1'-0"A11.1

52 F223 SCIENCESCALE: 1/4" = 1'-0"A11.1

53 F111 SCIENCESCALE: 1/4" = 1'-0"A11.1

54 F111 SCIENCESCALE: 1/4" = 1'-0"A11.1

55 F111 SCIENCESCALE: 1/4" = 1'-0"A11.1

56 F111 SCIENCE

SCALE: 1/4" = 1'-0"A11.1

32 F111 SCIENCESCALE: 1/4" = 1'-0"A11.1

31 F111 SCIENCE

LOCKS, TYP

CC

-29/

21/1

7A

DD

EN

DU

M C

C-2

CC-2

CC-2

CC-2CC-2

CC-2

CC-2

CC-2

CC-2

CC-2

CC-2

CC-2 CC-2

CC-2

CC-2

CC-2


2' - 9" 2' - 9" 2' - 9" 2' - 9" 1' - 0"

12' - 0"

2' -

10"

8"1'

- 0

"2'

- 6

"

7' -

0"

3' - 0" 3' - 0" 3' - 0" 3' - 0"

12' - 0"

W2052 W2052 W2052 W2052 H2051

D1223 D1223 D1223 D1223



3' - 0" 3' - 0" 2' - 9" 1' - 0"

9' - 9"

3' - 3" 3' - 3" 3' - 3"

9' - 9"

W2052 W2052 W2052 H2051

D1223 D1223 D1223

2' -

10"

8"1'

- 0

"2'

- 6

"

7' -

0"ELEC DEVICE

- SEE ELECTRICAL

EQ EQ EQ EQ EQ EQ

COUNTERTOP: SS-1VERTICAL: PL-1

21

A11.2

2' -

6"

1' -

8"

28' - 0"

EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ

ALIGN WITH METAL STUD, TYP

ALIGN WITH STEEL TUBE, TYP


PL-1

SS-1

4' -

2"

EQ EQ EQ EQ EQ EQ


21

A11.2

3' -

6"

EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ EQ

ALIGHN WITH STEEL TUBE, TYP

ALIGN WITH METAL STUD, TYP

28' - 0"


PL-1

SS-1

CABINETS: PL-1

EWC-2

3' - 0" 3' - 0"

T2052 T2052

EWC-1

WOOD BENCH PROVIDEDBY ATHLETIC LOCKERMANUFACTURER, TYP

6' - 10" 6' - 10"


RECESSEDPULLS, TYP

3/4" PLY WOOD

4" BASE, PLAM-4,APPLIED DIRECTLYTO GWB

HSS 3X3X1/4 TUBE STEEL SUPPORT @4'-0" O.C. MAX, AND 6" FROM EACHEND

5X8X3/8 BASEPLATE W/ (2) 1/2" DIAM. X2 1/2" EMBEDDED EXPANSIONANCHORS

6" MTL STUDS @ 16" O.C.3/4" PLYWOOD

1/2" SOLID SURFACING(SS) TYP

EASED EDGES

1/8

1/4

COUNTER TOP SUPPORT

3/4" PLYWOOD

1/2" SOLID SURFACING (SS) TYP

1/2" SOLID SURFACING (SS) TYP

8"3'

- 6

"

2' -

6"

3/4" MDF BOTH SIDES

PL-1, BOTH SIDES

3/4" SUPPORT BRACKET,PLAM- 5 ON PLY WD

OUTLETS PER ELECTRICAL

PL-2

LIGHT FIXTURE, PER ELECTRICALDRAWINGS

3/4" PLY WOOD

4" BASE, PLAM-4,APPLIED DIRECTLYTO 1/4" PLYWOOD

1' - 6"

3' -

6"

2"

3"

3/4" MDF

1' - 8"

1/4

HSS 3X3X1/4 TUBE STEEL SUPPORT @4'-0" O.C. MAX, AND 6" FROM EACHEND

1/2" PLATE W/ (2) 1/2" DIAM. X 2 3/4"THROUGH BOLT ANCHORS

HSS 1X1X3/16, PROVIDEAT EACH VERTICAL POST

2" GROMMET PLACED 4'-0" OC, STARTING2'-0" FROM PLAN WEST EDGE

1/8

6" MTL STUDS @ 16" O.C.

PL-1

SS-1

TS-1

WALL TYPE PER PLAN

2"x2" EDGE NAILER

3/4" PLYWOOD

1 1/2" x 1 1/2" STEEL ANGLE 24"VERTICAL LEG 18" HORIZONTAL LEGFASTEN TO METAL STUDS @ 16" O.C.

FASTEN WITH #10SCREW @ 6" O.C.

PL-2

UN

O2'

- 1

0"

WALL FINISH, PER SCHEDULE

8" @ SIM1' - 8"

5/8" MDF

PL-1

EXISTING WALL

SOLID SURFACE

1' -

0"

2' -

6"

3' -

6" PLASTIC LAMINATE


LIGHT FIXTURE -SEE ELECTRICAL

SOLID SURFACE

PLASTIC LAMINATE


LIGHT FIXTURE -SEE ELECTRICAL

1' -

0"

2' -

6"

3' -

6"

Arc

hite

ctu

re E

ngin

eering

P

lan

nin

g In

teriors

©

,

DL

R G

rou

p inc., a

Ne

bra

ska

co

rpo

ratio

n, A

LL

RIG

HT

S R

ES

ER

VE

D

Rev

isio

ns

9/2

0/2

017 1

:47:0

2 P

M

C:\R

evit\1

0-1

3125-3

0_A

R_2016_C

entr

al_

jlim

bach.r

vt

10-1

3125-3

0

8/2

9/2

017

PLA

TT

EV

IEW

JR

HIG

H &

HIG

H S

CH

OO

L R

EN

OV

AT

ION

S

CA

SE

WO

RK

ELE

VA

TIO

NS

A11.2

20

17

SP

RIN

GF

IELD

PLA

TT

EV

IEW

CO

MM

UN

ITY

SC

HO

OLS

SCALE: 1/4" = 1'-0"A11.2

11 F115 CONFERENCE ROOMSCALE: 1/4" = 1'-0"A11.2

12 F225 CONFERENCE ROOMSCALE: 1/4" = 1'-0"A11.2

14 F232 LEARNING COMMONSSCALE: 1/4" = 1'-0"A11.2

16 F232 LEARNING COMMONSSCALE: 1/4" = 1'-0"A11.2

13 F244 GYMNASIUM

SCALE: 1" = 1'-0"A11.2

21 DESK SECTIONSCALE: 1" = 1'-0"A11.2

23 RECEPTION DESK - SECTIONSCALE: 1" = 1'-0"A11.2

24 TYP. WALL MOUNTED COUNTERSCALE: 1/4" = 1'-0"A11.2

25 F206 RECEPTIONSCALE: 1/4" = 1'-0"A11.2

26 F206 RECEPTION

CC

-29/

21/1

7A

DD

EN

DU

M C

C-2

CC-2

CC-2

CC-2

CC-2

CC-2

CC-2

CC-2 CC-2

A B C

D

E F G H J K

1

2

3

4 5

6

7

8

9

10

11

EXISTING HEAT PUMP ANDACCOCIATED DUCTWORK ANDPIPING TO BE REMOVED. (TYP)

EXISTING HOTWATER BOILERSTO BE REMOVED

EXISTING CONDENSERWATER PUMPS TO BEREMOVED

EXISTING HOT WATERHEATER AND STORAGETANK TO BE REMOVED

EXISTING HEAT EXCHANGERAND CIRCULATION PUMP TOBE REMOVED

EXISTING TOWERSTORAGE TANK TOBE REMOVED

REMOVE ALL CONDENSER WATERPIPING AND ACCESSORIES ASSOCIATEDWITH BOILER/TOWER HEAT PUMP LOOP.

REMOVE ALL CONDENSER WATERPIPING IN VERTICAL CHASE

REMOVE EXISTING EXHAUSTDUCTWORK. COORDINATE WITH ARCHTO SEAL PENETRATION IN FLOOR.

GENERAL DEMOLITION NOTES:

1. THE EXTENT OF REMOVAL FOR THIS PROJECT SHALLGENERALLY CONSIST OF REMOVAL OF THE AIR SIDECOMPONENTS OF THE EXISTING HEAT PUMP SYSTEM.THIS SHALL INCLUDE ALL EXISTING GEOTHERMAL HEATPUMPS, AS WELL AS ALL ASSOCIATED DUCTWORK,DIFFUSERS, GRILLES, AND CONTROLS. ITEMS TO BEREMOVED SHALL BE SHOWN IN FULL-TONE. ITEMS TOREMAIN SHALL REMAIN HALF-TONE.

2. PIPING AND DUCTWORK REMOVAL SHALL INCLUDE THEREMOVAL OF ALL EXISTING PIPE HANGERS AND DUCTHANGERS.

3. THE ACTUAL LOCATIONS OF THE EQUIPMENT AND/ORPIPING AND DUCTWORK MAY VARY SLIGHTLY DUE TOAS-BUILT CONDITIONS. ANY PIPING OR DUCTWORKTHAT IS TO BE REMOVED SHALL BE REMOVED IN ITSENTIRETY. NO DUCTWORK OR PIPING SHALL BEABANDONED IN PLACE UNLESS IT HAS BEENSPECIFICALLY CALLED OUT TO BE ABANDONED INPLACE. IF UNEXPECTED CONDITIONS AREENCOUNTERED, NOTIFY THE OWNER'SREPRESENTATIVE. THE CONTRACTOR SHALL BEARTHE COSTS OF DAMAGE RESULTING FROM FAILURE TOEXERCISE REASONABLE CARE FOR CONTINUINGOPERATIONS WITHOUT NOTIFYING THE OWNER.

4. PRIOR TO ANY NEW WORK BEING COMPLETED, THEENTIRE HEAT PUMP WATER LOOP, SHALL BEEMPTIED, FLUSHED, AND CLEANED. DISCONNECT ALLEQUIPMENT FROM WATER LOOP PER THESPECIFICATIONS AND DRAWING DETAILS PRIOR TOFLUSHING. OWNER'S REPRESENTATIVE SHALL SIGNOFF ON WATER QUALITY PER SPECIFICATIONS.

5. WHERE DEMOLITION OCCURS, PATCH ALL ROOF ANDWALL PENETRATIONS TO MATCH EXISTING CONDITIONS.

Arc

hite

ctu

re E

ngin

eering

P

lan

nin

g In

teriors

©

,

DL

R G

rou

p inc., a

Ne

bra

ska

co

rpo

ratio

n, A

LL

RIG

HT

S R

ES

ER

VE

D

KEY PLAN

LEGEND NOTESLEGEND NOTES ARE COMMON TO ALLSOME NOTES MAY NOT APPLY TO THIS SHEET

A

NO

RT

H

Rev

isio

ns

B

C

D

E

F

9/2

2/2

017 2

:54:1

4 P

M

C:\R

evit\1

0-1

3125-3

0_M

P_2016_C

entr

al_

mm

art

z.r

vt

10-1

3125-3

0

8/2

9/2

017

PLA

TT

EV

IEW

JR

HIG

H &

HIG

H S

CH

OO

L R

EN

OV

AT

ION

S

HV

AC

DE

MO

LIT

ION

PLA

N, LO

WE

R L

EV

EL -

AR

EA

FM

D1.1

F

20

17

SP

RIN

GF

IELD

PLA

TT

EV

IEW

CO

MM

UN

ITY

SC

HO

OLS


HVAC DEMOLITION PLAN, LOWER LEVEL - AREA F

CC

-39/

25/1

7A

DD

EN

DU

M C

C-3

CC-3

A B C

D

E F G H J K

1

2

3

4 5

6

7

8

9

10

11

EXISTING HEAT PUMP ANDACCOCIATED DUCTWORK ANDPIPING TO BE REMOVED. (TYP)

REMOVE ALL CONDENSER WATERPIPING IN VERTICAL CHASE

REMOVE COOLING TOWER AND ALLPIPING AND ACCESSORIES ASSOCIATEDWITH BOILER/TOWER HEAT PUMP LOOP.

REMOVE ALL CONDENSER WATERPIPING AND ACCESSORIES ASSOCIATEDWITH BOILER/TOWER HEAT PUMP LOOP.

EXISTING EXHAUST FAN ON ROOFAND ACCOCIATED DUCTWORK TOBE REMOVED. COORDINATE WITHARCHITECTURE TO SEALPENETRATIONS IN ROOF.

EXISTING EXHAUST FAN ON ROOFAND ACCOCIATED DUCTWORK TO BEREMOVED. COORDINATE WITHARCHITECTURE TO SEALPENETRATIONS IN ROOF.

EXISTING HEAT PUMPS ANDACCOCIATED DUCTWORK TO BEREMOVED. COORDINATE WITHARCHITECTURE TO SEALPENETRATIONS IN ROOF.

GENERAL DEMOLITION NOTES:

1. THE EXTENT OF REMOVAL FOR THIS PROJECT SHALLGENERALLY CONSIST OF REMOVAL OF THE AIR SIDECOMPONENTS OF THE EXISTING HEAT PUMP SYSTEM.THIS SHALL INCLUDE ALL EXISTING GEOTHERMAL HEATPUMPS, AS WELL AS ALL ASSOCIATED DUCTWORK,DIFFUSERS, GRILLES, AND CONTROLS. ITEMS TO BEREMOVED SHALL BE SHOWN IN FULL-TONE. ITEMS TOREMAIN SHALL REMAIN HALF-TONE.

2. PIPING AND DUCTWORK REMOVAL SHALL INCLUDE THEREMOVAL OF ALL EXISTING PIPE HANGERS AND DUCTHANGERS.

3. THE ACTUAL LOCATIONS OF THE EQUIPMENT AND/ORPIPING AND DUCTWORK MAY VARY SLIGHTLY DUE TOAS-BUILT CONDITIONS. ANY PIPING OR DUCTWORKTHAT IS TO BE REMOVED SHALL BE REMOVED IN ITSENTIRETY. NO DUCTWORK OR PIPING SHALL BEABANDONED IN PLACE UNLESS IT HAS BEENSPECIFICALLY CALLED OUT TO BE ABANDONED INPLACE. IF UNEXPECTED CONDITIONS AREENCOUNTERED, NOTIFY THE OWNER'SREPRESENTATIVE. THE CONTRACTOR SHALL BEARTHE COSTS OF DAMAGE RESULTING FROM FAILURE TOEXERCISE REASONABLE CARE FOR CONTINUINGOPERATIONS WITHOUT NOTIFYING THE OWNER.

4. PRIOR TO ANY NEW WORK BEING COMPLETED, THEENTIRE HEAT PUMP WATER LOOP, SHALL BEEMPTIED, FLUSHED, AND CLEANED. DISCONNECT ALLEQUIPMENT FROM WATER LOOP PER THESPECIFICATIONS AND DRAWING DETAILS PRIOR TOFLUSHING. OWNER'S REPRESENTATIVE SHALL SIGNOFF ON WATER QUALITY PER SPECIFICATIONS.

5. WHERE DEMOLITION OCCURS, PATCH ALL ROOF ANDWALL PENETRATIONS TO MATCH EXISTING CONDITIONS.

Arc

hite

ctu

re E

ngin

eering

P

lan

nin

g In

teriors

©

,

DL

R G

rou

p inc., a

Ne

bra

ska

co

rpo

ratio

n, A

LL

RIG

HT

S R

ES

ER

VE

D

KEY PLAN


A

NO

RT

H

Rev

isio

ns

B

C

D

E

F

9/2

2/2

017 2

:54:1

5 P

M

C:\R

evit\1

0-1

3125-3

0_M

P_2016_C

entr

al_

mm

art

z.r

vt

10-1

3125-3

0

8/2

9/2

017

PLA

TT

EV

IEW

JR

HIG

H &

HIG

H S

CH

OO

L R

EN

OV

AT

ION

S

HV

AC

DE

MO

LIT

ION

PLA

N, M

AIN

LE

VE

L -

AR

EA

FM

D1.2

F

20

17

SP

RIN

GF

IELD

PLA

TT

EV

IEW

CO

MM

UN

ITY

SC

HO

OLS


HVAC DEMOLITION PLAN, MAIN LEVEL - AREA F

CC

-29/

20/1

7A

DD

EN

DU

M C

C-2

CC-2

UP

S

S

S

S

S

FS

S S

S

S

S

SS

S

S

S

S

S

S

SS

S

S

S

S

S

A

A

B

B

C

C

D

D

E

E

F

F

G

G

H

H

J

J

K

K

1

2

3

4 5

6

7

8

9

10

11

ELECTRICAL

F104

MECHANICAL

F103

VEST

F124

STORAGE

F122MEDIA CENTER

F121

COMPUTER LAB

F108

CLASSROOM

F109

CLASSROOM

F110

CLASSROOM

F120

CLASSROOM

F117

CLASSROOM

F119

CLASSROOM

F118

SCIENCE

F111

CONFERENCEROOM

F115

DATA

F113

CUSTODIAL

F102

STORAGE

F114

CORRIDOR

107

CORRIDOR

F101

CORRIDOR

F116

RAMP/STAIR

F1S1

GREEN ROOM

F123

8"x10" SA

8" ø130 CFM

D-1

10"x

8" S

A

8" ø130 CFM

D-1

8" ø130 CFM

D-1

8" ø130 CFM

D-1

HP-F05

8" ø130 CFM

D-1

8" ø130 CFM

D-1

6" ø120 CFM

D-1

6" ø120 CFM

D-16" ø

120 CFM

D-1

HP-F03

8" ø225 CFM

D-1

8" ø225 CFM

D-1

8" ø225 CFM

D-1

HP

-F02

8" ø130 CFM

D-1

8" ø130 CFM

D-1

8" ø130 CFM

D-1

HP-F01

10" ø285 CFM

D-1

10" ø265 CFM

D-1

10" ø265 CFM

D-1

6" ø75 CFM

D-1

10" ø365 CFM

D-1

10" ø365 CFM

D-1

10" ø365 CFM

D-1

HP-F06

HP-F08

HP

-F10

HP

-F09

10" ø250 CFM

D-110" ø

250 CFM

D-1

6" ø100 CFM

D-1

6" ø100 CFM

D-1

HP-F11

6" ø120 CFM

D-1

6" ø120 CFM

D-1

6" ø120 CFM

D-1

HP-F07

HP

-F04

8" ø220 CFM

D-1

18"x12" SA10"x12" SA

10"x8" SA

8"x10" SA

12"x

10"

SA

10"x8" SA

10"x

10"

SA

18"x

10"

SA

8" ø335 CFM

D-2

8" ø335 CFM

D-2

8" ø335 CFM

D-2

6"x8

" S

A

200 CFM

250 CFM

300 CFM

100 CFM

250 CFM

250 CFM

250 CFM

250 CFM

250 CFM

UH-F1

GDWH-F103

T-F103

ET-1

TMV-1

FIRE PUMPROOM

F103A

8"x6" EA 10"x10" EA

8"x6

" E

A

10"x

10"

EA

10"ø

OA

14"x

12"

OA

20"x14" OA

12"ø

OA

10"ø

OA

26"x14" OA10

"ø O

A

26"x

14"

OA

30"x

14"

OA

10"ø

OA

8"ø

OA

14"x10" OA

20"ø

SA

AC-F1

34"x

14"

OA

34/14 OA UP

10"ø OA

G-224" x 24"

G-224" x 24"

30"x

14"

OA

10"ø OA

10"ø OA

R-136" x 18"

G-224" x 24"

14"x12" RA

10"ø SA

12"x12" TA

12"x12" RA

D-224" x 24"12"x12" TA

12"x12" TA

24"x

12"

RA

G-224" x 24"

10"ø OA

14"x12" RA

G-224" x 24"

12"x12" TA

14"x12" RA

G-224" x 24"

12"x12" TA

20"x16" RA

G-224" x 24"

20"x16" RA

12"x12" TA

12"x12" TA

14"x12" RA

G-224" x 24"12"x12" TA

16"x14" SA

10/10 EA UP

10"x10" EA

24"x14" RA

CC- 1

G-112" x 12"120 CFM

12"x12" TA

REFRGERANT PIPING UPTO CU-F01 ON ROOF

G-112" x 12"150 CFM

G-112" x 12"150 CFM

G-112" x 12"75 CFM

G-124" x 24"

G-124" x 24"

G-124" x 24"

G-124" x 24"

G-124" x 24"

G-124" x 24"

G-124" x 24"

G-124" x 24"

G-124" x 24"

G-124" x 24"

G-124" x 24"

G-124" x 24"

G-124" x 24"

G-112" x 12"

G-112" x 12"

12"x12" TA

12"x12" TA

12"x12" TA

G-224" x 24"

R-224"x6"

175 CFM(TYP 4)

300 CFM

250 CFM

SP-2

SP-3

ROUTE DUCTWORK AS HIGH ASPOSSIBLE. RE-USE CURRENTPENETRATIONS IN WALL

24"x14" RA

18"x10" RA

CC-2

3" FLUE AND COMBUSTION AIRUP TO ROOF THRU CHASE.

GENERAL HVAC PLAN NOTES:

1. LIMIT ALL FLEXIBLE DUCT RUNS TO 3 FEET MAXIMUM LENGTH.FLEXIBLE DUCT(S) SHALL BE OF THE SAME SIZE AS THE DIFFUSERNECKS THAT THEY CONNECT TO UNLESS NOTED OTHERWISE.

2. COORDINATE EXACT LOCATIONS OF ALL DIFFUSERS WITHELECTRICAL, FIRE SPRINKLERS, AND GRID CEILINGS.

3. BALANCING DAMPERS SHALL BE LOCATED ABOVE ACCESSIBLE CEILINGS. IF THIS IS NOT POSSIBLE, ACCESS PANELS SHALL BE PROVIDED. ACCESS PANELS SHALL BE TAMPERPROOF

LOCKABLE ACCESS PANLES FOR ACCESS TO CONTROL VALVES,MOTORIZED DAMPERS, SHUT-OFF VALVES, AND SIMILARCOMPONENTS THAT ARE NOT LOCATED OVER AN ACCESSIBLECEILING. VOLUME DAMPERS SHALL BE PROVIDED WITH REMOTEDAMPER OPERATORS WITH ADJUSTABLE COVER IN NON-ACCESSABLE CEILING AREAS. SEE DETAIL 8, SHEET M4.2,"REMOTE VOLUME DAMPER" AND SPECIFICATIONS FORFURTHER INFORMATION.

4. PROVIDE CEILING AND/OR WALL ACCESS DOORS FOR ACCESS TODUCT ACCESS DOORS RELATED TO THE INSPECTION ANDRESETTING OF FIRE DAMPERS AND COMBINATION SMOKE ANDFIRE DAMPERS. PROVIDE MINIMUM 18" X 18" SIZE. CEILINGAND/OR WALL ACCESS DOOR RATING SHALL BE EQUIVALENT TOCEILING AND/OR WALL WHERE DOOR IS TO BE INSTALLED.

5. BRANCH DUCT SIZES SHALL BE THE SAME AS THE NECK SIZE OFTHE DIFFUSERS OR THE CONNECTION SIZE OF THE GRILLES,UNLESS NOTED OTHERWISE.

6. HORIZONTAL HEAT PUMPS:A. MANUFACTURER-RECOMMENDED SERVICE ACCESS AREAS

FOR HORIZONTAL HEAT PUMPS HAVE BEEN SHOWN ON THEPLANS.

B. LOCATE THE HORIZONTAL HEAT PUMP UNITS IN AREAS THATALLOW FOR EASY REMOVAL OF THE FILTER AND EASYACCESS TO HEAT PUMP UNIT ACCESS PANELS. LEAVEENOUGH SPACE FOR SERVICE PERSONNEL TO PERFORMMAINTENANCE OR REPAIR. PROVIDE SUFFICIENT ROOM TOMAKE WATER, ELECTRICAL, DUCT AND CONDENSATE DRAINCONNECTIONS.

C. IF ANY DUCTWORK OR PIPING (DOMESTIC WATER, FIRE,WATER LOOP, CONDENSATE DRAIN, NATURAL GAS,ELECTRICAL CONDUIT, CONTROLS CONDUIT IS RUN WITHINTHE SERVICE AREAS, THE PIPE, CONDUIT OR DUCT SHALL BEREMOVED AND RE-ROUTED IF POSSIBLE SO IT IS NOT WITHINTHE SERVICE AREA.

D. ALLOW ADEQUATE ROOM BELOW THE HEAT PUMP UNIT FORA CONDENSATE TRAP. DO NO LOCATE THE HEAT PUMP UNITABOVE ANY PIPING SYSTEMS WHERE POSSIBLE. EACHHORIZONTAL HEAT PUMP UNIT SHALL BE PROVIDED WITH AFILTER BRACKET FOR SIDE FILTER REMOVAL. THECONTRACTOR MAY CONVERT OR MODIFY THIS FILTERBRACKET TO ALLOW FOR BOTTOM REMOVAL OF THE FILTERIF IT PROVIDES A BETTER, MORE ACCESSIBLE INSTALLATION.

E. GENERALLY SPEAKING, HORIZONTAL HEAT PUMPS ARELOCATED AS HIGH AS POSSIBLE, BUT STILL ACCESSIBLEFROM A LADDER.

7. VERTICAL HEAT PUMPS:A. SEE 'VERTICAL HEAT PUMP INSTALLATION' DETAIL ON SHEET

M4.1 FOR REQUIREMENTS.

8. FOR OUTSIDE AIR SUPPLY DUCTWORK SIZES TO HEAT PUMPS,REFER TO HEAT PUMP SCHEDULE ON SHEET M5.1.

9. GENERALLY SPEAKING, DUCTWORK THROUGHOUT THE BUILDINGWAS LOCATED AS HIGH AS POSSIBLE TO ALLOW ROOM FORFITTINGS DOWN TO DIFFUSERS AND OTHER TRADES.

10. RTU EXHAUST OUT OF CLASSROOMS SHALL EQUAL THE OUTSIDEAIR CFM TO CLASSROOM UNLESS STATED OTHERWISE.

Arc

hite

ctu

re E

ngin

eering

P

lan

nin

g In

teriors

©

,

DL

R G

rou

p inc., a

Ne

bra

ska

co

rpo

ratio

n, A

LL

RIG

HT

S R

ES

ER

VE

D

KEY PLAN


A

NO

RT

H

Rev

isio

ns

B

C

D

E

F

9/2

2/2

017 2

:53:4

1 P

M

C:\R

evit\1

0-1

3125-3

0_M

P_2016_C

entr

al_

mm

art

z.r

vt

10-1

3125-3

0

8/2

9/2

017

PLA

TT

EV

IEW

JR

HIG

H &

HIG

H S

CH

OO

L R

EN

OV

AT

ION

S

HV

AC

PLA

N, LO

WE

R L

EV

EL -

AR

EA

FM

1.1

F

20

17

SP

RIN

GF

IELD

PLA

TT

EV

IEW

CO

MM

UN

ITY

SC

HO

OLS


HVAC PLAN, LOWER LEVEL - AREA F

CC

- 19/

13/1

7A

DD

EN

DU

M C

C-1

CC

-29/

20/1

7A

DD

EN

DU

M C

C-2

DN

FS

FS

S

SS

S

S

S

SS

FS

FS

FS

FS

SS

FS

S

SS

S

S

S

S

S

SS

S

S

S

S H

S

S

S

S

A B C

D

E F G H J K

1

2

3

4 5

6

7

8

9

10

11

OFFICE

F234CLASSROOM

F233

VEST

F201

EARLYEDUCATION

F202

EARLYEDUCATION

F203BOYS

F204

GIRLS

F205

BOYS

F213

GIRLS

F214

PRINCIPAL

F207

NURSE

F209WORK ROOM

F211

GUIDANCE

F208

CLASSROOM

F222

CLASSROOM

F221

SPECIAL ED

F230JANITOR

F216

CLASSROOM

F228

TEACHERSLOUNGE

F220

WOMENS

F217

MENS

F218CLASSROOM

F229

SCIENCE

F223

CONFERENCEROOM

F225

ELEC

F224

RECEPTION

F206

CORRIDOR

F212

LEARNINGCOMMONS

F232

TOILET

F210

OFFICE

F235

STORAGE

F226

OFFICE

F231

CORRIDOR

F219

CORRIDOR

F215

COORIDOR

F227

34"x14" RA

HP-F25

HP

-F24

HP

-F22

HP

-F19

HP

-F20

HP

-F14

HP

-F18

100 CFM

300 CFM

HP

-F21

HP

-F17

HP

-F16

HP

-F15

12"x8" OA

14"x

8" O

A

14"x8" OA

16"x10" OA

22"x

10"

OA

14"x10" OA

24"x12" OA 16"x12" OA 14"x10" OA

10"x

8" O

A

10"x

8" O

A

10"x

8" O

A

8"x6" EA

8"x6" EA

12"x8" EA

18"x

10"

EA

18"x10" EA

18"x14" EA

22"x

14"

EA

20"x

10"

EA

12"x8" EA

14"x10" EA

20"x6" SA 18"x8" SA 18"x8" SA 18"x8" SA

20"x10" SA

18"x12" SA

12"ø

SA

12" ø565 CFM

D-1

12" ø565 CFM

D-1

24"x10" RA

8"ø OA

16"x10" SA

6" ø150 CFM

D-1

6" ø150 CFM

D-1

6" ø150 CFM

D-1

6" ø150 CFM

D-1

26"x16" OA

20"x8" RA

G-224" x 24"

14"x10" SA

12"x

8" O

A

8"ø

OA

8"ø OA

34/14 OA DN

8" ø230 CFM

D-1

TYP 2

16"x

10"

SA

8" ø200 CFM

D-18" ø

200 CFM

D-1

8" ø200 CFM

D-1

8" ø200 CFM

D-1

8"x1

0" S

A

G-224" x 24"

22"x22" RA

8"x8" TA

12"x12" TA

R-120" x 6"

400 CFM

R-120" x 6"

350 CFM

R-120" x 6"

350 CFM

R-120" x 6"

350 CFM

R-120" x 6"

350 CFM

30"x8" RA

8"x8" TA

8" ø270 CFM

D-1

12"x12" TA

10"x

8" O

A

14"x

10"

SA

8" ø315 CFM

D-1

8" ø315 CFM

D-16" ø

70 CFM

D-1

12"x12" TA

14"x

10"

SA

10"x10" SA

8" ø230 CFM

D-1

8" ø235 CFM

D-18" ø

235 CFM

D-1

10"x10" SA

8" ø230 CFM

D-1

8" ø235 CFM

D-18" ø

235 CFM

D-1

14"x10" SA

16"x10" OA

10"x10" SA

8" ø235 CFM

D-18" ø

235 CFM

D-1

8" ø230 CFM

D-1

14"x

10"

SA

10"x8" EA

10"x8" EA10"x8" EA

14"x10" SA

8" ø230 CFM

D-1

8" ø235 CFM

D-18" ø

235 CFM

D-1

10"x10" SA

12"x12" TA

10"x8" OA

20"ø SA

16"ø

SA

16"ø

SA

12" ø565 CFM

D-4

TYP 4

16"x12" EA

10/10 EA DN

R-130" x 24"

1250 CFM

30"X12" RA UPTO RTU-F01

20"X20" SA UPTO RTU-F01

G-124" x 24"

12"x12" TA

HP-F23

12"ø SA

8"ø

EA

12"ø SA16

"x14

" S

A

34"x

14"

EA

12"x6" OA

8" ø250 CFM

D-1

8" ø250 CFM

D-1

8" ø250 CFM

D-1

8" ø250 CFM

D-1

8" ø230 CFM

D-1

8" ø240 CFM

D-1

8" ø230 CFM

D-1

G-224" x 24"

G-224" x 24"

12"x10" SA

12"x12" SA

24"x8" RA

G-224" x 24"

G-112" x 12"100 CFM

12"x12" TA

10" ø325 CFM

D-1

10" ø325 CFM

?

8" ø200 CFM

D-110" ø

275 CFM

D-1

8"x6

" O

A

G-124" x 24"

G-124" x 24"

G-124" x 24"

G-124" x 24"

G-124" x 24"

G-124" x 24"

G-124" x 24"

G-124" x 24"

G-124" x 24"

G-112" x 12"100 CFM

G-112" x 12"100 CFM

G-112" x 12"100 CFM

8"x8" TA

G-112" x 12"

G-112" x 12"

10"x

6" O

A

12"x

8" O

A

G-224"x24"G-2

24"x24"

G-224"x24"

G-224"x24"

G-224"x24"

G-224"x24"

G-224"x24"

G-224"x24"

G-112" x 12"

G-112" x 12"

G-112" x 12"150 CFM

G-112" x 12"150 CFM

CC- 1

HP

-F12

G-124" x 24"

6" ø75 CFM

D-1

6" ø75 CFM

D-1

G-224" x 24"

HP

-F13

270 CFM

90 CFM

210 CFM

210 CFM

260 CFM

200 CFM

200 CFM

200 CFM

200 CFM

260 CFM

150 CFM

120 CFM

12"x

10"

OA

10"ø

OA

10"ø OA

G-124" x 24"

12"x10" SA 8"x8" SA

R-18" x 6"

100 CFM

R-18" x 6"

100 CFM

12"x12" TA

R-18" x 6"

50 CFM

R-18" x 6"

50 CFM

G-112" x 12"225 CFM

G-112" x 12"225 CFM

10"x10" EA10"x10" EA

8"x6

" E

A

10/10 EA OPENTO PLENUM

10"x10" TA

10"x10" TA

R-218"x6"

175 CFM(TYP 4)

24"x

8" R

A

22"x8" RA

12"x

12"

SA

10"x

12"

SA

14"x14" SA

24"x8" RA24"x8" RA

22"x8" RA22"x8" RA

24"x12" RA

20"x8" RA

32"x8" RA

30"x12" RA

10"x

10"

SA

30"x

10"

SA

CC-2

GENERAL HVAC PLAN NOTES:

1. LIMIT ALL FLEXIBLE DUCT RUNS TO 3 FEET MAXIMUM LENGTH.FLEXIBLE DUCT(S) SHALL BE OF THE SAME SIZE AS THE DIFFUSERNECKS THAT THEY CONNECT TO UNLESS NOTED OTHERWISE.

2. COORDINATE EXACT LOCATIONS OF ALL DIFFUSERS WITHELECTRICAL, FIRE SPRINKLERS, AND GRID CEILINGS.

3. BALANCING DAMPERS SHALL BE LOCATED ABOVE ACCESSIBLE CEILINGS. IF THIS IS NOT POSSIBLE, ACCESS PANELS SHALL BE PROVIDED. ACCESS PANELS SHALL BE TAMPERPROOF

LOCKABLE ACCESS PANLES FOR ACCESS TO CONTROL VALVES,MOTORIZED DAMPERS, SHUT-OFF VALVES, AND SIMILARCOMPONENTS THAT ARE NOT LOCATED OVER AN ACCESSIBLECEILING. VOLUME DAMPERS SHALL BE PROVIDED WITH REMOTEDAMPER OPERATORS WITH ADJUSTABLE COVER IN NON-ACCESSABLE CEILING AREAS. SEE DETAIL 8, SHEET M4.2,"REMOTE VOLUME DAMPER" AND SPECIFICATIONS FORFURTHER INFORMATION.

4. PROVIDE CEILING AND/OR WALL ACCESS DOORS FOR ACCESS TODUCT ACCESS DOORS RELATED TO THE INSPECTION ANDRESETTING OF FIRE DAMPERS AND COMBINATION SMOKE ANDFIRE DAMPERS. PROVIDE MINIMUM 18" X 18" SIZE. CEILINGAND/OR WALL ACCESS DOOR RATING SHALL BE EQUIVALENT TOCEILING AND/OR WALL WHERE DOOR IS TO BE INSTALLED.

5. BRANCH DUCT SIZES SHALL BE THE SAME AS THE NECK SIZE OFTHE DIFFUSERS OR THE CONNECTION SIZE OF THE GRILLES,UNLESS NOTED OTHERWISE.









8. FOR OUTSIDE AIR SUPPLY DUCTWORK SIZES TO HEAT PUMPS,REFER TO HEAT PUMP SCHEDULE ON SHEET M5.1.

9. GENERALLY SPEAKING, DUCTWORK THROUGHOUT THE BUILDINGWAS LOCATED AS HIGH AS POSSIBLE TO ALLOW ROOM FORFITTINGS DOWN TO DIFFUSERS AND OTHER TRADES.

10. RTU EXHAUST OUT OF CLASSROOMS SHALL EQUAL THE OUTSIDEAIR CFM TO CLASSROOM UNLESS STATED OTHERWISE.

Arc

hite

ctu

re E

ngin

eering

P

lan

nin

g In

teriors

©

,

DL

R G

rou

p inc., a

Ne

bra

ska

co

rpo

ratio

n, A

LL

RIG

HT

S R

ES

ER

VE

D

KEY PLAN


A

NO

RT

H

Rev

isio

ns

B

C

D

E

F

9/2

2/2

017 2

:53:5

0 P

M

C:\R

evit\1

0-1

3125-3

0_M

P_2016_C

entr

al_

mm

art

z.r

vt

10-1

3125-3

0

8/2

9/2

017

PLA

TT

EV

IEW

JR

HIG

H &

HIG

H S

CH

OO

L R

EN

OV

AT

ION

S

HV

AC

PLA

N, M

AIN

LE

VE

L -

AR

EA

FM

1.2

F

20

17

SP

RIN

GF

IELD

PLA

TT

EV

IEW

CO

MM

UN

ITY

SC

HO

OLS


HVAC PLAN, MAIN LEVEL - AREA F

CC

- 19/

13/1

7A

DD

EN

DU

M C

C-1

CC

-29/

20/1

7A

DD

EN

DU

M C

C-2

UP

SS

S

S

S

S

S

S

SS

S

A

A

B

B

C

C

D

D

E

E

F

F

G

G

H

H

J

J

K

K

1

2

3

4 5

6

7

8

9

10

11

MEDIA CENTER

F121

1601 SF

STORAGE

F122175 SF

GREEN ROOM

F123

180 SF

CLASSROOM

F120

791 SF

CORRIDOR

F101947 SF

CLASSROOM

F119718 SF

CLASSROOM

F118714 SF

CLASSROOM

F117725 SF

CLASSROOM

F110703 SF

CORRIDOR

F116382 SF

CONFERENCEROOM

F115

213 SF

DATA

F113

134 SF

STORAGE

F11459 SF

SCIENCE

F111999 SF

CORRIDOR

107453 SF

COMPUTER LAB

F108747 SF

CLASSROOM

F109742 SF

GIRLS

F106163 SF

BOYS

F105

131 SF

CUSTODIAL

F102207 SF

RAMP/STAIR

F1S1

715 SF

MECHANICAL

F103583 SF

ELECTRICAL

F104126 SF

VEST

F124

39 SF

HP-F06

HP-F05

HP-F07

HP-F03

HP

-F04

HP

-F02

HP-F01

HP-F11

HP-F08

HP

-F09

HP

-F10

1"1" CR1"1" CS

1"1" CR

1"1" CS

1 1/2"1 1/2" CS1 1/2"1 1/2" CR

3/4"3/4" CR3/4"3/4" CS

1 1/2"1 1/2" CS

1 1/2"1 1/2" CR

1"1" CR1"1" CS

1 1/2"1 1/2" CS

1 1/2"1 1/2" CR

1"1" CS1"1" CR 1 1/2"1 1/2" CR

1 1/2"1 1/2" CS

1"1" CS

1"1" CR

1"1" CR1"1" CS

1"1" CS1"1" CR

2"2" CS2"2" CR

1"1" CR1"1" CS

1"1" CS1"1" CR

2"2" CS2"2" CR

3/4"3/4" CS3/4"3/4" CR

1 1/4"1 1/4" CS

1 1/4"1 1/4" CR

2 1/2"2 1/2" CR2 1/2"2 1/2" CS

4"4" CR

4"4" CR

CONDESER WATER LINES ROUTEDUNDERGROUND TO GEOTHERMAL VAULT.SEE SITE UTILITY PLAN FOR CONTINUATION

CS/R PIPING UP. SEE SHEETM2.2F FOR CONTINUATION P-F02

P-F01CS/R PIPING ROUTED UNDERFLOOR OF ROOM F233

GENERAL HVAC PIPING PLAN NOTES:

1. VALVES SHALL BE LOCATED ABOVE ACCESSIBLE CEILINGS. IFTHIS IS NOT POSSIBLE, ACCESS PANELS SHALL BE PROVIDED.ACCESS PANELS SHALL BE TAMPERPROOF LOCKABLE PANELSFOR ACCESS TO CONTROL VALVES, MOTORIZED DAMPERS,SHUT-OFF VALVES, VOLUME DAMPERS AND SIMILAR COMPONENTSTHAT ARE NOT LOCATED OVER AN ACCESSIBLE CEILING.

2. GENERALLY SPEAKING, WATER LOOP PIPING SHALL BE RUN ASHIGH AS POSSIBLE, BETWEEN JOISTS AND THROUGH JOISTWEBBING TO PROVIDE MAXIMUM CLEARANCE TO DUCTWORK ANDOTHER TRADES. PIPING SHALL BE AT LOW ENOUGH ELEVATIONTO ALLOW PROPER BRANCH TAPS TO BE MADE (OFF TOP OF MAINS)AND ROUTED TO THEIR ASSOCIATED HEAT PUMPS. STACK PIPINGWHERE REQUIRED.

3. WLS AND WLR PIPING CONNECTIONS TO HEAT PUMPS ARE SIZEDAS SHOWN ON THE HEAT PUMP SCHEDULE. SEE SHEET M5.1.

4. CONDENSATE DRAIN (CD) PIPING IS SIZED AS SHOWN ON THEHEAT PUMP SCHEDULE. SEE SHEET M5.1. WHERE CD IS NOTSHOWN ON THE DRAWINGS, ROUTE TO THE NEAREST FLOORDRAIN.









7. BRANCH PIPING CONNECTIONS FROM THE PIPING MAINS SHALL BE TAKEN OFF THE TOP OR SIDES OF THE PIPE. BRANCH PIPING OFF THE BOTTOM OF THE WATER LOOP PIPING MAINS IS SPECIFICALLY PROHIBITED UNLESS IT HAS BEEN SPECIFICALLY SHOWN TO BE PIPEDOFF THE BOTTOM OF THE PIPING MAIN.

8. REFRIGERANT PIPE SIZES SHALL BE AS DETERMINED BY THESUCCESSFUL MANUFACTURER.

Arc

hite

ctu

re E

ngin

eering

P

lan

nin

g In

teriors

©

,

DL

R G

rou

p inc., a

Ne

bra

ska

co

rpo

ratio

n, A

LL

RIG

HT

S R

ES

ER

VE

D

KEY PLAN


A

NO

RT

H

Rev

isio

ns

B

C

D

E

F

9/2

2/2

017 2

:53:5

1 P

M

C:\R

evit\1

0-1

3125-3

0_M

P_2016_C

entr

al_

mm

art

z.r

vt

10-1

3125-3

0

8/2

9/2

017

PLA

TT

EV

IEW

JR

HIG

H &

HIG

H S

CH

OO

L R

EN

OV

AT

ION

S

HV

AC

PIP

ING

PLA

N, LO

WE

R L

EV

EL -

AR

EA

FM

2.1

F

20

17

SP

RIN

GF

IELD

PLA

TT

EV

IEW

CO

MM

UN

ITY

SC

HO

OLS


HVAC PIPING PLAN, LOWER LEVEL - AREA F

CC

- 19/

13/1

7A

DD

EN

DU

M C

C-1

CC

-29/

20/1

7A

DD

EN

DU

M C

C-2

CC- 1

CC-2

DN

UP

S

S

S

S

S

SS

S

S

S

S H

A B C

D

E F G H J K

1

2

3

4 5

6

7

8

9

10

11

GYMNASIUM

F2442718 SF

STORAGE

F245159 SF

MECHANICAL

F24673 SF

OFFICE

F23564 SF

OFFICE

F23464 SF

CLASSROOM

F233922 SF

GIRLS

F243208 SF

BOYS

F242184 SF

STORAGE

F24096 SF

KITCHEN

F239

585 SF

COORIDOR

F241128 SF

ALCOVE

F236

68 SF

JANITOR

F23795 SF

ELECTRICAL

F238

98 SF

LEARNINGCOMMONS

F2321085 SF

RAMP/STAIR

F1S1715 SF

CORRIDOR

F2121373 SF

RECEPTION

F206

272 SF

WORK ROOM

F211149 SFNURSE

F209

118 SF

TOILET

F21062 SF

GUIDANCE

F208281 SF

PRINCIPAL

F207244 SF

VEST

F201

126 SF

EARLYEDUCATION

F202666 SF

EARLYEDUCATION

F203473 SF

BOYS

F20420 SF

GIRLS

F20520 SF

TEACHERSLOUNGE

F220344 SF

CORRIDOR

F219203 SF

CLASSROOM

F221746 SF

CLASSROOM

F222757 SF

CLASSROOM

F228725 SF

CLASSROOM

F229713 SF

SPECIAL ED

F230642 SF

OFFICE

F231

67 SF

STORAGE

F226

94 SF

CONFERENCEROOM

F225236 SFSCIENCE

F2231089 SF

ELEC

F22465 SF

MENS

F21863 SF

WOMENS

F21764 SF

JANITOR

F21644 SF

GIRLS

F214163 SF

BOYS

F213131 SF

CORRIDOR

F215327 SF

COORIDOR

F227384 SF

VEST

F24745 SF

HP

-F22

HP

-F21

HP

-F20

HP

-F19

HP

-F18

HP

-F17

HP

-F16

HP

-F15 H

P-F

14H

P-F

13

HP

-F24

HP-F23

HP-F25

1"1" CR1"1" CS

1 1/4"1 1/4" CR

1 1/4"1 1/4" CS

1 1/2"1 1/2" CS

1 1/2"1 1/2" CR

1"1" CR

1"1" CS

1 1/2"1 1/2" CS

1 1/2"1 1/2" CR

1 1/2"1 1/2" CR1 1/2"1 1/2" CS

1"1" CR1"1" CS 2 1/2"2 1/2" CS

2 1/2"2 1/2" CR1"1" CR1"1" CS

2 1/2"2 1/2" CS

2 1/2"2 1/2" CR

1"1" CR

1"1" CS

2 1/2"2 1/2" CS

2 1/2"2 1/2" CR

1"1" CR

1"1" CS

2 1/2"2 1/2" CS

2 1/2"2 1/2" CR

1 1/4"1 1/4" CS

1 1/4"1 1/4" CR

1"1" CR1"1" CS

1 1/2"1 1/2" CS

1 1/2"1 1/2" CR

3"3" CR3"3" CS

3"3" CS3"3" CR

1 1/2"1 1/2" CR1 1/2"1 1/2" CS

1"1" CS

1"1" CR

1 1/2"1 1/2" CR

1 1/2"1 1/2" CS

1"1" CS

1"1" CR

1"1" CS

1"1" CR

1 1/4"1 1/4" CS1 1/4"1 1/4" CR

4"4" CS

4"4" CR

P-F01

P-F02

2-1/2" CS/R DOWN TOSERVE LOWER LEVEL

4" CONDENSER WATER THRUWALL TO CEILING PLENUM.ROUTE PIPING TO EXTERIORPLUMBING CHASE.

ROUTE PIPING AS HIGH ASPOSSIBLE IN JOIST SPACEABOVE CORRIDOR.

CC- 1

ET-F2

AS-F1

GENERAL HVAC PIPING PLAN NOTES:

1. VALVES SHALL BE LOCATED ABOVE ACCESSIBLE CEILINGS. IFTHIS IS NOT POSSIBLE, ACCESS PANELS SHALL BE PROVIDED.ACCESS PANELS SHALL BE TAMPERPROOF LOCKABLE PANELSFOR ACCESS TO CONTROL VALVES, MOTORIZED DAMPERS,SHUT-OFF VALVES, VOLUME DAMPERS AND SIMILAR COMPONENTSTHAT ARE NOT LOCATED OVER AN ACCESSIBLE CEILING.

2. GENERALLY SPEAKING, WATER LOOP PIPING SHALL BE RUN ASHIGH AS POSSIBLE, BETWEEN JOISTS AND THROUGH JOISTWEBBING TO PROVIDE MAXIMUM CLEARANCE TO DUCTWORK ANDOTHER TRADES. PIPING SHALL BE AT LOW ENOUGH ELEVATIONTO ALLOW PROPER BRANCH TAPS TO BE MADE (OFF TOP OF MAINS)AND ROUTED TO THEIR ASSOCIATED HEAT PUMPS. STACK PIPINGWHERE REQUIRED.

3. WLS AND WLR PIPING CONNECTIONS TO HEAT PUMPS ARE SIZEDAS SHOWN ON THE HEAT PUMP SCHEDULE. SEE SHEET M5.1.

4. CONDENSATE DRAIN (CD) PIPING IS SIZED AS SHOWN ON THEHEAT PUMP SCHEDULE. SEE SHEET M5.1. WHERE CD IS NOTSHOWN ON THE DRAWINGS, ROUTE TO THE NEAREST FLOORDRAIN.









7. BRANCH PIPING CONNECTIONS FROM THE PIPING MAINS SHALL BE TAKEN OFF THE TOP OR SIDES OF THE PIPE. BRANCH PIPING OFF THE BOTTOM OF THE WATER LOOP PIPING MAINS IS SPECIFICALLY PROHIBITED UNLESS IT HAS BEEN SPECIFICALLY SHOWN TO BE PIPEDOFF THE BOTTOM OF THE PIPING MAIN.

8. REFRIGERANT PIPE SIZES SHALL BE AS DETERMINED BY THESUCCESSFUL MANUFACTURER.

Arc

hite

ctu

re E

ngin

eering

P

lan

nin

g In

teriors

©

,

DL

R G

rou

p inc., a

Ne

bra

ska

co

rpo

ratio

n, A

LL

RIG

HT

S R

ES

ER

VE

D

KEY PLAN


A

NO

RT

H

Rev

isio

ns

B

C

D

E

F

9/2

2/2

017 2

:53:5

3 P

M

C:\R

evit\1

0-1

3125-3

0_M

P_2016_C

entr

al_

mm

art

z.r

vt

10-1

3125-3

0

8/2

9/2

017

PLA

TT

EV

IEW

JR

HIG

H &

HIG

H S

CH

OO

L R

EN

OV

AT

ION

S

HV

AC

PIP

ING

PLA

N, M

AIN

LE

VE

L -

AR

EA

FM

2.2

F

20

17

SP

RIN

GF

IELD

PLA

TT

EV

IEW

CO

MM

UN

ITY

SC

HO

OLS


HVAC PIPING PLAN, MAIN LEVEL - AREA F

CC

- 19/

13/1

7A

DD

EN

DU

M C

C-1

CC

-29/

20/1

7A

DD

EN

DU

M C

C-2

CC-2

20'-0" (TYP)

1", 33 GPM PER BORE (TYP)

NO 90° ELBOWS (TYP), SEE WELLDETAIL 1/M4.3

20'-0

" (T

YP

)

FROM VALVE VAULT, TYP.

2"2"1-1/2"1-1/2"1-1/4"1"1"

2" 2" 1-1/2" 1-1/2" 1-1/4" 1"

TO VALVE VAULT

WLR

WLR

WLS

WLS

2"

1"

5'-0

" M

IN(V

ER

IFY

)

6"x2" WELD-O-LET (TYP)

PRESSURE / TEMPERATURE TESTPORT (TYP)

2" WLR (2" WLS BEYOND)

2" BALANCING VALVE W/ SHUT-OFF VALVE ON WLR (TYP)

PIPE SUPPORT (TYP) SPACE EVERY10'-0" FOR STEEL PIPE. SPACE PER MFRSRECOMMENDATIONS FOR POLYETHYLENE PIPE (TYP)

POLYETHYLENE x STEEL PIPEADAPTOR (TYP) SEE PIPING NOTE 1

4" WLR4" WLSSHUT-OFF VALVE NOT SHOWN. SEE PLAN VIEW.

SAND BACKFILL (SEE 235800.)

COATED 14 GA. COPPER TRACEWIRE ATTACHED TO PIPE ALONGENTIRE LENGTH

COMPACTED EARTH BACKFILL (ROCKFREE)

ORIGINAL GRADE

COMPACTED TRENCH BACKFILL

FILL BOREHOLE WITH THERMALLYENHANCED BENTONITE GROUT

MAIN RADIUS = 25 TIME DIAMETERBACKFILL THIS AREA BY HAND TOPREVENT KINKING OF PIPE.

REVERSE RETURN PIPING (PERHEADER PIPING DETAIL)

WLS HEADER PIPING

2'-0"

18"

(MIN

)

4" 5'-0" (MIN)

1" SDR II POLYETHYLENE PIPE RATEDAT160 PSIG @ 78° F (SEESPECIFICATIONS) NO JOINTSALLOWED BETWEEN HEADER ANDU-BEND

PREFABRICATED U-BEND CONNECTION

NOTE: WLS-WLR TO BE PIPED IN A REVERSE RETURN CONFIGURATION

300'

-0"

BO

RE

DE

PT

H6"

DIA

. BO

RE

WLR HEADER PIPING

1

REFERENCED NOTES:

1. MINIMUM TRENCH DEPTH IS 60". IF AT 60" DEPTH THE BOTTOM OF THETRENCH IS OF SOIL WITH ROCKS AND SHARP STONES, CONTRACTORSHALL OVER-EXCAVATE AN ADDITIONAL 12" AND REPLACE SPOILED SOILWITH COMPACTED SAND BACKFILL. SEE SPECIFICATION 235800.

90° ELBOW DN(TYP)

ISOLATION VALVE ON WLR

4" WLS

4" WLR

2'-6

"M

IN

POLYETHYLENE x STEELPIPE ADAPTOR. (TYP)SEE PIPING NOTE 1.

STEEL PIPE HEADERMANIFOLD (TYP)SEE PIPING NOTE 1.

2" SHUT-OFF VALVE ON WLS (TYP)

SEAL ANNULAR SPACEBETWEEN PIPE ANDSLEEVE WITH FLEXIBLEPOLYURETHANE FOAM(TYP)

HOSE ADAPTOR (TYP)

2" PURGE / DRAINVALVE (TYP)

BLIND FLANGE (TYP)

THERMOMETER (TYP)PRESSURE GAUGE (TYP)

1'-0"(TYP)

1'-0"(TYP)

2" WLS (TYP)

2" WLR (TYP)

2" SHUT-OFF VALVE ON WLS (TYP)

2" BALANCING VALVE W/ SHUT-OFF VALVE ON WLR (TYP)SET BALANCING VALVE AT 45GPM

36"

MIN

X"

Ø C

OM

BU

ST

ION

AIR

INT

AK

E

COMBUSTION AIR OPTION 1 COMBUSTION AIR OPTION 2 GAS VENT

X"

Ø C

OM

BU

ST

ION

AIR

INT

AK

E

APPROVED RAIN CAP

ROOF FLASHING

1" CLEARANCE

ROOF FLASHING

1" CLEARANCE

X"

Ø G

AS

VE

NT

ING

36"

MIN

APPROVED VENT TERMINAL

GUY WIRES. ATTACH TO ROOFSTRUCTURE.

36"

MIN

36"

MIN

10'

6' M

IN

A SCREEN WITH MESH SIZE NOT SMALLER THAN1" X 1" SHALL BE INSTALLED AT THE INLET OF THEDUCTED COMBUSTION AIR DUCT

THE BOILER VENT TERMINATION SHALL BEAT LEAST 3 FEET ABOVE ANY FORCED-AIRBUILDING INLET THAT IS LOCATED WITHIN10 FEET OF THE BOILER VENT.

-

-10'

NOTE:INTAKETHE BOILER AIR INTAKE SHALL BE LOCATED AT LEAST 3 FEET BELOW ANY VENT TERMINATION WITHIN 10 FEET.INSTALL LARGE-MESH SCREENS TO PROTECT AGAINST THE ENTRY OF FOREIGN OBJECTS BUT THE 'FREEAREA' SHALL BE AT LEAST TWICE THE FLUE CROSS-SECTIONAL AREA.

VENTVENT VERTICAL DISCHARGE SHALL EXTEND AT LEAST 3 FEET ABOVE THE ROOF THROUGH PROPERLY FLASHEDPENETRATIONS, AND AT LEAST 2 FEET ABOVE ANY OBJECT WITHIN A 10-FOOT HORIZONTAL DISTANCE.

HYDRONIC INDICATOR SYSTEM, MOUNTON PIPE

FLEXIBLE CONNECTION

SUCTION DIFFUSER

SUPPORT LEG

HOUSEKEEPING PAD

PUMP BASE PLATE

REDUCER

SILENT LIFT CHECK VALVE

SHUT-OFF VALVE (TYP)

FLOOR

BLOW DOWN VALVE WITH CAP

AIRFLOW

AIRFLOW

AIRFLOW

OA DUCT WITH BALANCING DAMPER

PIPING CONNECTIONS SEE, *

FLEXIBLE DUCT CONN. TYP.

WATER SOURCE HEAT PUMP

SPRING VIBRATION ISOLATORS(TYP OF 4)

3/8" SUPPORT RODS DOWN FROMSTRUCT. (TYP. OF 4)

RA DUCT W/ BALANCING DAMPER

SA DUCT W/ BALANCING DAMPER

RETURN AIR

HEAT PUMP

MECHANICAL CONTRACTOR SHALLPROVIDE SHEET METAL OR PLYWOODEQUAL IN SIZE TO FILTER & LABEL"FILTER PULL SPACE DO NOTREMOVE" ON BOTH SIDES. SECTIONSSHALL REMAIN IN-PLACE UNTIL LAY-IN-CEILING PANELS ARE INSTALLED ATWHICH TIME THE MECHANICALCONTRATOR SHALL REMOVE THESIGN. SUPPORT FROM STRUCTUREOR FROM DUCTWORK.

FILTER PULL SPACE

DO NOT R

EMOVE

SUPPLYAIRFLOW

RETURNAIRFLOW

OUTSIDEAIRFLOW

SUPPLY DUCTBALANCINGDAMPER

WLS/WLR PIPING.FOR CONNECTIONTO HEAT PUMP SEEDETAIL 6/M4.1

VERTICAL HEAT PUMP

MASON INDUSTRIES SUPER KNEOPRENE PAD OR EQUALSIZE AS REQUIRED BYEQUIPMENT WEIGHT (TYP 4)

PIPE CONDENSATE DRAINTO FLOOR DRAIN.SEE 18/M4.1

OUTSIDE AIR DUCTBALANCING DAMPER

RETURN DUCTBALANCING DAMPER

INSTALLATION NOTES:

1. GENERALLY, 1 OR 2 VERTICAL HEAT PUMPS WILL BE LOCATEDIN EVERY HEAT PUMP CLOSET.

2. CARE HAS BEEN TAKEN IN THE ARRANGEMENT OF THEMECHANICAL COMPONENTS WITHIN THE CLOSET TO ALLOWSUFFICIENT SERVICE ACCESS TO CONTROLS, COMPRESSORS,REFRIGERATION COMPONENTS, FILTERS, BLOWER AND BLOWERMOTOR. ALL SYSTEM COMPONENTS SHALL GENERALLY BEINSTALLED AS SHOWN ON THE PLANS AND PER THIS DETAIL.

3. HEAT PUMP SHOULD BE LOCATED WITH ACCESS TO FILTER ANDSERVICE PANEL(S) AT SIDE(S) OF MACHINE. CONSULTMANUFACTURER FOR LOCATION OF ACCESS PANEL. A MINIMUM36-INCH CLEARANCE SHOULD BE ALLOWED IN FRONT OF EACHSERVICE ACCESS PANEL SIDE.

4. THE ARRANGEMENT OF THE MECHANICAL COMPONENTS HASBEEN DESIGNED TO ALLOW ADEQUATE CODE-REQUIREEDCLEARANCES AROUND ELECTRICAL DISCONNECTS IN THESECLOSETS. SEE ELECTRICAL PLANS FOR LOCATIONS OF THESEDISCONNECTS.A. ELECTRICAL CONDUIT & PIPE ROUTING MUST NOT BLOCK

FILTER REMOVAL. FILTERS OFTEN PULL STRAIGHT UP,SOMETIMES THEY ARE REMOVABLE FROM SIDE. ALSO,CONDUIT & PIPE ROUTING SHOULD NOT INTERFERE WITHACCESS PANELS.

INSTALLATION NOTES (CONT'D):

5. THE PIPING SHALL BE ARRANGED IN A MANNER THAT ALLOWSMAINTENANCE ACCESS TO THE TWO-WAY CONTROL VALVESAND HEAT PUMP HOSE KIT ASSEMBLY.A. ALL VALVES ON VERTICAL PIPES SHALL HAVE THEIR STEMS

ORIENTED TO GIVE MAXIMUM OPERATIONAL CLEARANCE,OR SHALL BE ORIENTED AS DIRECTED BY THE ENGINEER.

B. VALVES SHALL BE LOCATED SO AS TO BE EASILYACCESSIBLE TO THE OPERATOR OF THE EQUIPMENT.

C. AUTOMATIC FLOW CONTROL (BALANCE) VALVES SHALL BEORIENTED SO THE P/T PLUGS ARE ACCESSIBLE TO THEBALANCING CONTRACTOR.

D. AUTOMATIC 2-WAY (TEMPERATURE CONTROL VALVES)SHALL BE ORIENTED SO THAT THEIR VISUAL INDICATOR ISREADILY AND CLEARLY VISIBLE, AND THE OPEN/CLOSEPOSITION SHALL BE CLEARLY MARKED ON THE ACTUATOR.

E. VALVES SHALL BE LOCATED WITHIN 6'-0" AFF.F. PIPING SHALL BE RIGIDLY ANCHORED TO THE BUILDING

STRUCTURE SO AS TO PREVENT THE TRANSFER OFLOADING (WEIGHT) OR OTHER FORCES TO CONNECTIONSAT THE HEAT PUMP UNITS

6. BRANCH PIPING CONNECTIONS FROM THE WATER LOOP PIPINGMAINS IN THE CORRIDOR SHALL BE TAKEN OFF THE TOP OR SIDESOF THE PIPE. BRANCH PIPING OFF THE BOTTOM OF THE WATERLOOP PIPING MAINS IS SPECIFICALLY PROHIBITED.

7. THE DISCHARGE DUCT FROM EACH HEAT PUMP SHALL CONSISTOF A FLEXIBLE CONNECTOR AT THE HEAT PUMP UNIT, AND ATRANSITION PIECE FROM THE DISCHARGE COLLAR OF THE HEATPUMP TO THE PLAN DUCT SIZE. SEE PLANS FOR CONFIGURATIONOF TRANSITION PIECES (VARIES BY HEAT PUMP).

FLEXIBLE DUCTCONNECTIONW/BONDING JUMPER(BY ELECRICAL)ACROSS ALL FLEXCONNECTORS (TYP)

INSTALLATION NOTES (CONT'D):

8. ALL VERTICAL DUCTWORK THAT IS LOCATED ABOVE AFLEXIBLE DUCT CONNECTOR SHALL BE RIGIDLYSUPPORTED SO THE WEIGHT OF THE DUCTWORK DOESNOT BEAR ON THE FLEXIBLE DUCT CONNECTOR FABRICAT THE HEAT PUMP UNITS.

9. THE RETURN AIR DUCTS SHALL GENERALLY BEBROUGHT INTO THE MECHANICAL ROOM AS SHOWN,TYPICALLY AS HIGH TO STRUCTURE AS POSSIBLE.EACH RETURN DUCT SHALL HAVE A VOLUME DAMPER.THE RETURN DUCT AT EACH HEAT PUMP SHALL HAVE AVOLUME DAMPER AND A FLEXIBLE CONNECTOR.

10. EACH RETURN AIR DUCT CONNECTIONS AT THE HEATPUMP UNITS SHALL HAVE A SIDE ACCESS FILTER RACK.FILTER PULL ACCESS SHALL TYPICALLY BE BETWEENTHE TWO VERTICAL HEAT PUMPS, AND IS REPRESENTEDBY A DASHED AREA ON THE PLANS. THESECLEARANCES MUST BE MAINTAINED UPON FINALINSTALLATION OF MECHANICAL EQUIPMENT.

11. THE OUTDOOR AIR DUCT SHALL BE CONNECTED TO THERETURN AIR DUCT WITH A LOW LOSS FITTING. SEEPLANS FOR FITTING ARRANGEMENT. GENERALLY SPEAKING,OUTDOOR AIR DUCTS SHALL BE RUN AS HIGH ASPOSSIBLE, TIGHT TO STRUCTURE. WHEN DUCT ENTERSCLOSET AT A HIGHER ELEVATION THAN HEAT PUMPRETURN DUCTWORK, PROVIDE ELBOW DOWN TO LOW LOSSWYE FITTING (IN VERTICAL).

12. SERVICE CLEARANCE FOR HEAT PUMP UNITS HAS BEENREPRESENTED ON THE PLANS BY A DASHED AREA.THESE CLEARANCES MUST BE MAINTAINED UPON FINALINSTALLATION OF MECHANICAL EQUIPMENT.

P T

P T

WLS

CD PIPE TO DRAIN

HEATPUMP

UNION W/ P/T TEST PORT & MANUAL AIR VENT

2-WAY CONTROL VALVE FURNISEDBY TCC, INSULATED BY MC

INSULATED RETURN HOSE

INSULATED SUPPLY HOSE

CONDENSATE DRAIN P-TRAP SEEDETAIL 20/M4.1

BLOWDOWN VALVE W/ THREADEDHOSE CONNECTION

WYE TYPE STRAINER W/ INTEGRALBALL VALVE & P/T TEST PORTS

EXTENDED YOKES FOR INSULATION (TYP)AT VALVES & P/T PORTS

SHUT-OFF VALVE

BALL VALVE W/ INTEGRAL UNION,AUTOMATIC FLOW VALVE & DUAL P/TTEST PORTS

INSULATED CONDENSATE DRAINLINES

BRAIDED FLEXIBLE CONNECTOR W/ SWIVEL ENDAT EQUIP & FIXED END AT PIPING CONNECTION

P T P T

P T

UNION

5'-0" MAX

NOTE:FOR SAME HANGER DETAIL FOR PIPE TRAPEZE HANGERS

UNDERSIDE SUPPORTS OR SIDE-MOUNTED ANGLE BRACKETS BY HEATPUMP MFR

STEEL JOIST OR STEEL BEAM

MECHANICAL UNIT

3/8" THREADED RODS (BY MECH)

1-3/8" x 1-5/8" UNISTRUT CHANNELBETWEEN DECK RIBS (BY MECH)

WELD OR BOLT TO STEEL JOISTS (BYMECH)

LOOPED SUPPLY HOSE ORTEMPORARY PIPING

STRAINER

FLOW CONTROL VALVE

RETURN

SUPPLY

TERMINAL UNIT

THIS DETAIL IS NOT TO BE USED AS THE PIPING CONNECTION DETAIL FOR THE HEAT PUMPUNITS. THE PURPOSE OF THIS DETAIL IS TO ILLUSTRATE THE PROCEDURE TO BE USED FORBYPASSING THE HEAT PUMP UNITS DURING THE FLUSHING AND CLEANING OF THE HYDRONICSYSTEM. THIS IS METHODOLOGY AS OUTLINED BY GRISWOLD CONTROLS. REFER TO DETAILXX/M4.1 FOR HEAT PUMP UNIT CONNECTION DETAIL.

CLEANING AND DRAINING THE SYSTEM:

PRIOR TO FULL SYSTEM START-UP, ALL PIPING SHALL BE THOROUGHLY CLEANED TO REMOVE DIRT AND DEBRIS.TO FLUSH OUT THE PIPING SYSTEM PROPERLY, THE HOSE KITS SHALL BE MODIFIED AS SHOWN ON THE DETAIL BY"LOOPING THE SUPPLY HOSE AND RETURN PIPING TOGETHER, THUS BY-PASSING THE TERMINAL UNIT (HEATPUMP), AND FLOW CONTROL VALVE. THIS PROCEDURE SHALL BE USED TO PROTECT THE TERMINAL UNITS FROMCONTAMINATION.

PROCEDURE FOR "LOOPING" HOSES:

1. DISASSEMBLE THE RETURN SIDE HOSE KIT ASSEMBLY, BUT LEAVE THE BALL VALVE CONNECTED TO THERETURN PIPE.

2. REMOVE THE INTERNAL SCREEN FROM THE Y-STRAINER WHILE FLUSHING THE SYSTEM.3. LOOSEN THE SUPPLY SIDE HOSE FROM THE TERMINAL UNIT, AND "LOOP" IT DIRECTLY TO THE BALL VALVE ON

THE RETURN SIDE PIPING (A COUPLING MAY BE REQUIRED DEPENDING ON THE BALL VALVE CONNECTIONTYPE).

4. AFTER ALL HOSES HAVE BEEN "LOOPED", START THE SYSTEM PUMP TO CLEAN THE PIPING SYSTEM OFPARTICLES LARGER THAN APPROXIMATELY 1/16" IN DIAMETER (I.E. WELD SPLATTER, MILL SCALE, AND OTHERCONTAMINANTS). REFER TO "HYDRONIC PIPING" SPECIFICATION FOR CLEANING AND FLUSHINGINSTRUCTIONS.

FINAL CONNECTIONS:

1. SHUT OFF BOTH BALL VALVES ON THE SUPPLY AND RETURN CONNECTIONS TO THE UNITS. IF A STRAINER ANDDRAIN VALVE ARE INSTALLED, OPEN THE DRAIN VALVE TO REMOVE THE FLUSHING WATER FROM THECONNECTING HOSE.

2. BREAK THE TEMPORARY "LOOP", AND REINSTALL THE FLOW CONTROL VALVE AND THE RETURN SIDE HOSE.3. CONNECT BOTH HOSES TO THE TERMINAL UNIT AS SHOWN ON DETAIL XX/M4.1.4. REINSTALL THE INTERNAL SCREEN IN THE Y-STRAINER.5. OPEN BOTH SUPPLY AND RETURN BALL VALVES, AND FILL THE SYSTEM WITH FLUID.6. BLEED ANY ENTRAINED AIR SO THAT THE FLOW CONTROL VALVE WILL REMAIN FULL OF FLUID DURING

OPERATION.

BUILDING WALL INTERIOR

RIVET (TYP)

RECTANGULAR DUCTWORK

SEAL ALL WALL PENETRATIONS (TYP)

PIPING & INSULATION

GALV. STEEL DRAWBANDTYPE ESCUTCHEON, 3" WIDE

ROUND DUCTWORK

SATIN FINISH OR ALUMINUMSPLIT-TYPE ESCUTCHEON

SLEEVE IN MASONRY WALL (TYP)

CONCEALED DUCTWORK& PIPING

EXPOSED DUCTWORK& PIPING IN FINSHED SPACES

HANGER CLAMP OR BAND

BOLT

STRAP OR ANGLE

NUT

ANGLE

ROD

DUCT

LONG FLAT SPANS ON OVAL DUCTHAVE A TENDENCY TO SAG. OVALDUCT WITH A MAJOR AXIS OF 42INCHES OR MORE SHALL BEREINFORCED PER SMACNA HVACDUCT CONSTRUCTION STANDARDSTYPE 2.

CHANNEL OR ANGLE

NOTES:1. DO NOT EXCEED ALLOWABLE LOAD LIMITS OF ANY OR ALL OF THE INDIVIDUAL TRAPEZE PARTS.2. DO NOT PENETRATE DUCT OR DUCT INSULATION VAPOR BARRIER WHEN SECURING HANGERS TO

DUCTWORK. EVENTUALLY THE PENETRATIONS WILL LEAK.3. USE HANGER CLAMPS OR BANDS FOR ROUND DUCTS AS ROUND DUCT TENDS TO DEFORM ON

TRAPEZE HANGERS.4. TEARS, PUNCTURES, ETC. SHALL BE REPAIRED WITH TAPE OR MASTIC TO MAINAIN THE INTEGRITY

OF THE VAPOR BARRIER.5. DO NOT USE ANY STRAP HANGERS WITH SCREWS ON ANY DUCTWORK THAT IS EXTERNALY

WRAPPED.

PROVIDE A SECTION OF HIGHCOMPRESSION STRENGTHINSULATION AT EACH HANGER POINT.INSULATION MAY BE HALF ROUND ORFULL ROUND AND EXTENDED 2"BEYOND GALVANIZED SHIELD EACHWAY.

HANGER ROD WITH CLEVIS HANGER

PIPE

UNI-STRUT CHANNEL

GALV. IRON SHEET SHIELD (12" LONG)

INSULATION

PIPE

NOTES:

1. ATTACH SUPPORTS FOR ALL PIPING SUSPENDED FROM THE STEELSTRUCTURE TO THE TOP CHORD OF JOISTS OR BEAM.

2. PROVIDE COPPER OR PLASTIC COATED HANDERS FOR NON-INSULATED COPPER PIPE.

VD

LINEAR DIFFUSER

ROUND DUCT WRAP INSULATION

CEILING

SUPPLY MAIN WRAP INSULATION

45° ENTRY TAP RECTANGULAR TOROUND

FLEX CONNECTION NO BENDS MAX.5'-0" LONG

VD

DIFFUSER

ROUND DUCT WRAP INSULATION

CEILING

SUPPLY MAIN WRAP INSULATION

45° ENTRY TAP RECTANGULAR TOROUND

FLEX CONNECTION NO BENDS MAX.5'-0" LONG

WALL

1" ACCOUSTICAL DUCT LINER

W W * 1.5

NOTE:1) DAMPER MUST BE U.L. APPROVED & INSTALLED AS PER

MANUFACTURER U.L. RECOMMENDATIONS. UL555, UL555A & UL55C.2) PROVIDE ACCESS PANELS IN WALLS OR CHASES.

DUCT

MOUNTING ANGLE14 GA

DAMPER ACTUATOR(SMOKE & FIRE/SMOKE DAMPERS)

MOUNTING ANGLE14 GA

14 GA SLEEVE

FIRE, SMOKE, OR COMBINATIONFIRE/SMOKE DAMPER

BREAKDOWN JOINT

ALLOW FOR 1/8" EXP OF SLEEVE INSETTING ANGLES. ANGLES TO LAPSTRUCTURE A MIN. OF 1" AROUNDENTIRE OPENING.

DAMPERACCESS

WALL ORPARTITION

WLR

WLRWLS

WLS

4" FROM SYSTEM

4" ISOLATION VALVES, TYPICAL

THERMOMETER (TYP)

PLASTIC TO METAL PIPE FLANGETRANSITION.

METAL PIPE SYSTEM INSTALLED BYMECHANICAL CONTRACTOR.PLASTIC PIPE SYSTEM INSTALLED BYWELL FIELD CONTRACTOR.

4" TO GROUND LOOP FIELD VAULT

1" HOSE CONNECTION W/LOCKINGBALL VALVE (FILL & FLUSHING)

EMCS BULB WELL (TYP)

MANUAL AIR VENT (TYP)

4" TO PUMP SYSTEM

X"

Y"

INSTALL ADDITIONAL VENT ATINTERVALS OF 10' WHEN PIPINGDOWNSTREAM OF TRAP EXCEEDS15'

FLOOR DRAIN

CLEAN OUT

1" AIR GAP

PITCH DOWN TOWARD DRAIN

OPEN END

CLEAN OUT

DRAIN LINE SHALL BE AT LEAST THESAME SIZE AS THE NIPPLE ON THEDRAIN PAN

EQUIP MUST BE MOUNTED HIGHENOUGH VIA HOUSEKEEPING PADAND/OR EQUIPMENT RAILS TO ENSUREX AND Y DIMENSIONS

NOTES:1. ON DRAW-THRU UNITS, THE (X) DIMENSION (IN INCHES) SHALL BE 1.5 TIMES THE AIR HANDLING-UNITS

SUCTION PRESSURE AT OPERATING CONDITIONS, BUT IN NO CASE LESS THAN 2-INCHES.2. ON BLOW-THRU UNITS, THE (X) DIMENSION (IN INCHES) CAN BE AS SMALL AS 2 INCHES, BUT THE (Y)

DIMENSION (IN INCHES) SHALL BE 1.5 TIMES THE AIR HANDLING UNITS TOTAL STATIC PRESSURE BUTIN NO CASE LESS THAN 2 INCHES.

X=DISTANCE BETWEEN THE DRAIN PAN OUTLET AND THE TRAPY=TRAP DEPTH

3/4" BALL VALVE W/HOSE END THREADCONNECTION

THREAD PIPE CAP DO NOT SEAL WELD

LOW POINT

WELDOLET

SOCKET WELD

PITCH DOWNTO DRAIN

HVAC PIPING LOW POINT DRAINA

3/4" LEAD FREE BALL VALVE W/HOSEEND THREAD CONNECTION CAP ANDCHAIN

LOW POINT

PITCH DOWNTO DRAIN

PLUMBING PIPING LOW POINT DRAINB

REFRIGERANT LINES, CONDENSATELINE, AND CONDUIT (REFER TOPLANS)

PORTALS PLUS INC. MODEL C12 CAP

PORTALS PLUS INC. RC SERIES 18GAUGE GALVANIZED ROOF CURBSYSTEM 16" MIN

NOTES:1. CONTRACTOR SHALL ONLY CUT OPENINGS THRU ROOF DECK AND INSULATION THE SIZE REQUIRED

FOR THE PIPING TO BE INSTALLED. THE ROOF OPENING SHALL NOT BE CUT TO THE SIZE OF THEROOF CURB.

2. ROOF INSULATION SHALL BE CONTINUOUS INSIDE OF THE ROOF PENETRATION VAULT.3. THE VAULT/HOUSING, INCLUDING HOUSING CURB, PIPE COLLARS & SEALS, GASKETS AND STAINLESS

STEEL MOUNTING HARDWARE SHALL BE FURNISHED BY PORTALS PLUS INC.

Arc

hite

ctu

re E

ngin

eering

P

lan

nin

g In

teriors

©

,

DL

R G

rou

p inc., a

Ne

bra

ska

co

rpo

ratio

n, A

LL

RIG

HT

S R

ES

ER

VE

D

Rev

isio

ns

9/2

2/2

017 2

:53:5

8 P

M

C:\R

evit\1

0-1

3125-3

0_M

P_2016_C

entr

al_

mm

art

z.r

vt

10-1

3125-3

0

8/2

9/2

017

PLA

TT

EV

IEW

JR

HIG

H &

HIG

H S

CH

OO

L R

EN

OV

AT

ION

S

ME

CH

AN

ICA

L D

ET

AIL

SM

4.1

20

17

SP

RIN

GF

IELD

PLA

TT

EV

IEW

CO

MM

UN

ITY

SC

HO

OLS

SCALE: 3/8" = 1'-0"M4.1

1 GEOTHERMAL LOOP PIPING CIRCUITSCALE: 3/8" = 1'-0"M4.1

2 GEOTHERMAL VAULT SECTIONSCALE: 3/8" = 1'-0"M4.1

3 GEOTHERMAL BORE SECTIONSCALE: 3/8" = 1'-0"M4.1

4 GEOTHERMAL VAULT PLAN

SCALE: 12" = 1'-0"M4.1

5 COND BOILER / WATER HTR COMBUSTION AIR INTAKE & GAS VENTSCALE: 3/8" = 1'-0"M4.1

6 END SUCTION PUMPSCALE: 12" = 1'-0"M4.1

7 HEAT PUMP MOUNTINGSCALE: 3/8" = 1'-0"M4.1

8 HEAT PUMP FILTER ACCESS

SCALE: 3/8" = 1'-0"M4.1

9 VERTICAL AND HORIZONTAL HEAT PUMPSCALE: 3/8" = 1'-0"M4.1

10 HEAT PUMP PIPING

SCALE: 3/8" = 1'-0"M4.1

12 MECH UNIT HANGING DETAIL (UNIT WT <300LBS)

SCALE: 3/8" = 1'-0"M4.1

11 FLUSHING PIPING CONNECTION

SCALE: 3/8" = 1'-0"M4.1

13 DUCT/PIPE WALL PENETRATIONSSCALE: 3/8" = 1'-0"M4.1

14 DUCTWORK HANGING DETAILSCALE: 3/8" = 1'-0"M4.1

15 PIPE INSULATION AT HANGERSSCALE: 3/8" = 1'-0"M4.1

16 DIFF DUCT CONN HORIZ FLEX

SCALE: 3/8" = 1'-0"M4.1

17 TRANSFER DUCTSCALE: 3/8" = 1'-0"M4.1

18 COMBO FIRE/SMOKE DAMPERSCALE: 3/8" = 1'-0"M4.1

19 WATER LOOP ENTRANCE ISOSCALE: 3/8" = 1'-0"M4.1

20 CONDENSATE DRAIN P-TRAPSCALE: 12" = 1'-0"M4.1

21 LOW POINT DRAINSCALE: 12" = 1'-0"M4.1

22 ROOF PIPE PORTAL

CC

-29/

20/1

7A

DD

EN

DU

M C

C-2

CC-2

VV

BALANCING VALVE

CHECK VALVE

UNION (TYP)

PRESSURE GAUGE

STRAINER

ISOLATION VALVE (TYP)

INLINE PUMP

VV

DRAIN VALVE WITHHOSE END CONNECTIONS

V

V

V

TO PUMP SUCTION

FLOOR MOUNTED PRESSURIZEDEXPANSION TANK, ET-E02

STEEL ANGLE OR UNI-STRUT FOR AIRSEPARATOR LARGER THAN 8"

SET RELIEF VALVE AT 100 PSI

HIGH CAPACITY AIR VENT (TYP)

FOR AIR SEPARATOR 8" AND SMALLER ATTACH PIPEHANGERS TO THE TANGENTIAL NOZZLES. FOR AIRSEPARTATORS LARGER THAN 8" PROVIDE SUPPORTSUNDER SKIRT OF SEPARATORNOTE: DO NOT USE LIFTING LUGS TO SUPPORT UNIT

AIR SEPARATOR

CONNECT TO SIDE OF PIPING, TOP ORBOTTOM CONNECTION WILL NOT BEALLOWED

1"

ANTI-THERMO SIPHON LOOP, INSTALLPER MFR INSTRUCTIONS

3/4" DRAIN VALVE W/ THREADED HOSECAP (TYP)

4" HIGH EQUIP PAD BY GEN

FLOOR

V V V V 1” CW MAKE-UP

FULL SIZE BY-PASS

GLOBE VALVE

REDUCED PRESSURE BACKFLOWPREVENTER, RUN DRAIN LINE FULL SIZETO FD/FS

1/2" TAP OFF TOP OF CW LINE

CW SUPPLY 1-1/2" OR SMALLER SUPPLYINGA FLUSH VALVE

BALL VALVE

PROVIDE ADDITIONAL ACCESS PANEL ORLOCATE TRAP PRIMER BEHIND PLUMBINGCHASE ACCESS PANEL TRAP PRIMER SHALLBE WITHIN 16" OF ACCESS PANEL DOOR

TRAP PRIMER, PRECISION PLUMBINGPRODUCTS, PRIME-RITE MODELPR500SS OR EQUAL

PRECISION PLUMBING PRODUCTS,DISTRIBUTION UNIT

1/2" SEAMLESS COPPER TUBING TOFLOOR DRAIN TRAP PRIMERCONNECTION (TYP). ENTIRE LENGTH OFTUBING SHALL HAVE ARMAFLEXINSULATION. TUBING SHALL SLOPE TOFLOOR DRAIN WITH NO LOW POCKETS.

24"

MIN

NON-FREEZE POST HYDRANT

ROOF INSULATION

ROOF STRUCTURE

PIPE CLAMP

VALVE BOOT WITH 1/8" TAP FORBLEED FITTING CONNECTION

BALL VALVE

1/2" BALL DRIP,PIPE TO FLOOR DRAIN

RUBBER BOOT & FASTENER BYROOF SYSTEM MFR

OUTSIDEBUILDING

INSIDEBUILDING

GAS SERVICE TO BUILDING

3/8" GAUGE PORT WITH PLUG

GAS METER

GAS PRESSURE REGULATOR

UNION (TYP)

SERVICE SHUT-OFF VALVE MARK, OR TAG TOINDICATE THE EXISTENCE OF THE SEPARATEEMERGENCY POWER SUPPLY SHUTOFF VALVE

GAS SERVICE LINE

GRADE

2 PSI GAS SERVICE TO BUILDING. ALL EXTERIORGAS PIPING TO BE PAINTED WITH HIGHPERFORMANCE COATING

MECHANICAL LINK SEAL & GALVANIZED STEELPIPE SLEEVE. CAULK TO MAKE WEATHERTIGHT

TO EMERGENCY GENERATOR

MARK OR TAG TO INDICATE THE EXISTENCE OFTHE MAIN BUILDING SUPPLY SHUTOFF VALVE

ROOF

MAIN LEVEL

DRIP LEG

TOWATERHEATER

TO ROOF TOPUNITS ANDSCIENCE ROOM

LEADER, SAME SIZE AS DRAINAGELINE UP TO 4".USE 4" FOR LARGER DRAINAGE PIPING.

TWO-WAY PIPE FITTING

JAY R. SMITH FIGURE NO 4258C OR 4263LCLEANOUT HOUSING WITH BRONZE TAPERTHREAD CLEANOUT PLUG OR EQUAL

CONCRETE SIDEWALK OR PAVING (BYOTHERS)

GRADE CLEANOUT WITH FLUSHCOVERS. COORDINATE LOCATIONWITH JOINT PATTERN IN SIDEWALK, ORWHEN LOCATED ON GRADE, PROVIDE12" x 36" 2400 PSI CONCRETE PAD

3"

8"

PUMP ON

PUMP OFF

DIFFERENTIAL MERCURY FLOATSWITCH

BASIN

CHECK VALVE

SHUT-OFF VALVE

2" FORCE MAIN

STEEL COVER PLATE

FLOOR

INLET

34" 34

"

*

ADJUST LAVATORY SETBACKTO CLEAR INSIDE CASEWORK& ADA KNEE & TOE CLEARANCES

SEE SPECIFICATIONSFOR LAVATORY & TRIM

OFFSET WASTE

ADJUST WASTE CONNECTIONROUGH-IN AS REQUIRED FOR TRAPPARALLEL TO WALL TOWARDS COLDWATER SUPPLY SIDE

TRAP PARALLEL TO WALL

FLOOR

ESCUTCHEON

CASEWORK ENCLOSURE BY OTHERS

SEE SPECIFICATIONS FOR LAVATORY& TRIM

ESCUTCHEON

OFFSET WASTE

ADJUST WASTE CONNECTIONROUGH-IN AS REQUIRED FOR TRAPPARALLEL TO WALL TOWARDS COLDWATER SUPPLY SIDE

TRAP PARALLEL TO WALL

FLOOR

A WALL - MOUNTED A COUNTER - MOUNTED

THERMOMETER (TYP)

ROOF LINE

PROVIDE MFR'S VENTTERMINATION CAP FORCOMBUSTION AIR INLET DUCT,6-INCH DIAMETER (TYP)

PROVIDE MFR'S VENTTERMINATION CAP FOREXHAUST VENT (TYP)

2"

CO

MB

US

TIO

N A

IR

GA

S V

EN

T

RELIEF VALVE (TYP)

PER PVI, "TO MAXIMIZE WATER HEATER EFFICIENCY, DONOT CONNECT THE BUILDING RETURN OR DISHWASHERRECIRCULATION PIPING (≈ 5 GPM) DIRECTLY TO THE COLDINLET. CONNECTION DIRECTLY TO THE DEDICATED BUILDINGRETURN FITTING LOCATED AT THE REAR OF THE TANK ATMIDTANK LEVEL."

COLD INLET(BACK OF UNIT)

CONDENSATE DRAIN LINE(BACK OF UNIT)(TYP)

DRAIN VALVE (TYP)

6" HOUSE KEEPING PAD (TYP)

FLOOR

CONDENSATE TRAP

NEUTRALIZATION TANK

EXISTING FLOOR DRAIN

RE

L

GDWH-1

2"3/4"

CW

2"

P-F04

3/4"

G

140

HW

C

SHUT-OFF VALVE (TYP)

POUNDS TO INCHESREGULATOR (TYP)

UNION (TYP)

DIRT LEG (TYP)

SHUT-OFF (TYP)

UNION (TYP)

NC BYPASS VALVE

2"

2"

140

HW

RE

L

AQUASTAT

2"

T-1

HOUSE KEEPING PAD

3/4"

1"

CW

110

HW

C

110

HW

C

110

HW

C

140

HW

HEAT TRAP

TMV-1

1-1/2"

2"3/4"

140 HW

140 HWC

140 HW

110 HW

110 HWC

1-1/2"

1/2"

P-F03

(TYP)

2"

SHUT-OFF (TYP)

EXPANSION TANK

P-EX

1

M4.2

ET-1

1"

FLOOR

CLASSROOM STATION

CEILING

CONNECT TO DUAL GAS TURRET

ZONE MASTER GAS SHUT-OFF VALVE

STEEL PIPING TO RUN IN WALLRECESS NOT RIGIDLY SECUREDSEE ARCH

FROM GAS MAIN

TO ADDITIONAL GAS COCKS INCLASSROOM

G G

GAS SHUT-OFF PUSH BUTTON"EMERGENCY PANIC PUSH BUTTON",SEE SPEC. 231120

ROOM MASTER GAS SHUT-OFF PANEL"WALL MOUNTED UTILITY CONTROLPANEL", SEE SPEC. 231120

S

Arc

hite

ctu

re E

ngin

eering

P

lan

nin

g In

teriors

©

,

DL

R G

rou

p inc., a

Ne

bra

ska

co

rpo

ratio

n, A

LL

RIG

HT

S R

ES

ER

VE

D

Rev

isio

ns

9/2

2/2

017 2

:54:0

1 P

M

C:\R

evit\1

0-1

3125-3

0_M

P_2016_C

entr

al_

mm

art

z.r

vt

10-1

3125-3

0

8/2

9/2

017

PLA

TT

EV

IEW

JR

HIG

H &

HIG

H S

CH

OO

L R

EN

OV

AT

ION

S

ME

CH

AN

ICA

L D

ET

AIL

SM

4.2

20

17

SP

RIN

GF

IELD

PLA

TT

EV

IEW

CO

MM

UN

ITY

SC

HO

OLS

SCALE: 3/8" = 1'-0"M4.2

1 INLINE PUMPSCALE: 12" = 1'-0"M4.2

2 WATER SYSTEM MAKE-UP & AIR CONTROL PIPINGSCALE: 12" = 1'-0"M4.2

3 FLOOR DRAIN TRAP PRIMERSCALE: 3/8" = 1'-0"M4.2

4 POST HYDRANT ROOFSCALE: 12" = 1'-0"M4.2

5 GAS SERVICE ENTRANCE DETAILSCALE: 12" = 1'-0"M4.2

6 TWO WAY GRADE CLEANOUT DETAIL

SCALE: 12" = 1'-0"M4.2

7 SUMP PUMP DETAIL

SCALE: 12" = 1'-0"M4.2

10 ADA ACCESSIBLE LAVATORY OR COUNTER SINK DETAILSCALE: 12" = 1'-0"M4.2

9 DOMESTIC HOT WATER HEATER WITH STORAGE TANK DETAIL

SCALE: 3/8" = 1'-0"M4.2

8 MASTER GAS SHUTOFF

CC

-29/

20/1

7A

DD

EN

DU

M C

C-2

CC-2

CC-2

CC-2

PUMPS

PUMP MIN MOTOR DATA MECH

MARK SERVES LOCATION PUMP TYPE GPM HEADEFF

HP V PH HZ RPM BASIS OF DESIGNNOTES

(FT WG) (%) [WATTS]

P-F01 HEAT PUMP LOOP F246 END SUCTION 225 85 73 7.5 460 3 60 1760 TACO SFI2510C 1

P-F02 HEAT PUMP LOOP F246 END SUCTION 225 85 73 7.5 460 3 60 1760 TACO SFI2510C 1

P-F03 140 Deg. RETURN F103 LEAD FREE IN-LINE 2 9 - 1/40 115 1 60 3250 TACO 006B

P-F04 140 Deg. RECIR. F103 LEAD FREE IN-LINE 4 8 - 1/40 115 1 60 3250 TACO 006B

1. PUMP SHALL HAVE INTEGRATED PUMP AND VFD WITH WITH SELF-SENSING PRO-BALANCE TECHNOLOGY.

FAN SCHEDULE

FAN DATA ELECTRICAL DATAUNIT

FAN BLADEESP

FAN DRIVEHP MAX MOTORIZED WEIGHT

MECH

MARK SERVES TYPE TYPE CFM (IN WG) RPM TYPE [WATTS] V PH HZ dBA DAMPER (LBS) BASIS OF DESIGN NOTES

EF-C1 RM 247 ROOF CENTRIFUGAL 675 0.5 1100 DIRECT 1/4 120 1 60 51 YES 56 COOK ACE-D 120C13D 1,2,3,4,6




EF-C5 RM 259 ROOF CENTRIFUGAL 150 0.5 1375 DIRECT 1/8 120 1 60 46 YES 46 COOK ACE-D 90C15DL 1,2,3,4,5,6

EF-C6 RM 256 ROOF CENTRIFUGAL 300 0.5 1435 DIRECT 1/8 120 1 60 53 YES 46 COOK ACE-D 90C15DH 1,2,3,4,5,6

EF-C7 RM 255 ROOF CENTRIFUGAL 300 0.5 1435 DIRECT 1/8 120 1 60 53 YES 46 COOK ACE-D 90C15DH 1,2,3,4,5,6

EF-C8 RM 252 ROOF CENTRIFUGAL 150 0.5 1375 DIRECT 1/8 120 1 60 46 YES 46 COOK ACE-D 90C15DL 1,2,3,4,5,6

EF-F1 RM F233 ROOF CENTRIFUGAL 550 0.5 1463 DIRECT 1/8 120 1 60 46 YES 47 COOK ACE-DEC 100C17DEC 1,2,3,4,6,7

EF-F2 RM F233 ROOF CENTRIFUGAL 180 0.5 1550 DIRECT 1/8 120 1 60 46 YES 48 COOK ACE-D 70C15DH 1,2,3,4,6

MECHANICAL NOTES:

1. FAN SELECTION WITH THE FOLLOWING PARAMETER: NOT ALLOWED TO OPERATE IN MOTOR SAFETY FACTOR.

2. PROVIDE WITH 115 VOLT ALUMINUM MOTORIZED BACKDRAFT DAMPER AND ACTUATOR.

3. PROVIDE WITH SOLID STATE SPEED CONTROLLER, SHIPPED LOOSE FOR FIELD WIRING BY ELECTRICAL CONTRACTOR.

4. PROVIDE DISCONNECT SWITCH IN NEMA-1 ENCLOSURE FACTORY MOUNTED AND WIRED.

5. FAN SHALL BE INTERLOCKED WITH LIGHT/WALL SWITCH. LIGHT/WALL SWITCH AND FAN POWER WIRING BY ELECTRICAL CONTRACTOR.

6. PROVIDE 13-INCH HEIGHT INSULATED ROOF CURB WITH DOUBLE METAL SHELL LINER TO PROTECT CURB INSULATION FROM MOISTURE LADEN AIR.

7. FAN CONNECTED TO LABORATORY FUME HOOD. INTERLOCK FAN OPERATION WITH FUME HOOD SWITCH.

DIFFUSER, REGISTER & GRILLE SCHEDULE

MAX MAX OPPOSED PANEL FACE MECH

MARK STATIC PD NC BLADE FRAME SIZE SIZE FINISH MATERIAL BASIS OF DESIGN NOTES

(IN WG) (DECIBELS) DAMPER TYPE (IN) (IN)

D-1 0.10 25 --- SEE PLANS 24x24 24x24 WHITE STEEL PRICE SPD 1,2,3

D-2 0.10 25 --- SEE PLANS 24x24 24x24 WHITE STEEL PRICE PPD2 1,2,3,6,8

D-3 0.10 35 --- LAY-IN SEE PLANS SEE PLANS WHITE STEEL PRICE TDAC 1,2,5

D-4 0.10 35 --- LAY-IN SEE PLANS SEE PLANS WHITE STEEL PRICE RCD 1,2,9

R-1 0.10 25 PRICE DAL SURFACE SEE PLANS SEE PLANS WHITE STEEL PRICE 920D 1,2

R-2 0.10 25 PRICE DAL SURFACE SEE PLANS SEE PLANS WHITE ALUMINUM PRICE SDGE 1,2,7

G-1 0.08 25 --- LAY-IN SEE PLANS SEE PLANS WHITE ALUMINUM PRICE 80 1,2,3

G-2 0.08 25 --- SEE PLANS SEE PLANS SEE PLANS WHITE ALUMINUM PRICE 80FF 1,2,3,4

MECHANICAL NOTES:

1. NC VALUES ARE BASED ON A ROOM ABSORPTION OF 10 db, RE 10-12 WATTS.

2. SEE PLANS FOR NECK SIZE AND CFM.

3. COORDINATE WITH CEILINGS ON FRAME TYPE. PROVIDE A ALUMINUM SURFACE MOUNT ADAPTER FRAME FOR GYP CEILING INSTALLATION.

4. PROVIDE WITH A MERV-8 RATED FILTER WITH GRILLE.

5. UNIT SHALL INCLUDE A SELF-ACTING THERMAL EXPANSION ACTUATOR. AT SA TEMPERAURES BELOW 68 DEG F THE SUPPLY AIR IS DISCHARGED HORIZONTALLY. AT 75 DEG F THE SA

IS DISCHARGED AT A SLIGHT DOWNWARD ANGLE. ABOVE 75 DEG F THE SA IS ANGLED DOWNWARD WITH FULL VERTICAL PROJECTION AT A SA ABOVE 82 DEG F.

6. DIFFUSER TO PROVIDE VAV HEATING AND COOLING. PROVIDE WITH A WALL-MOUNTED ASSEMBLY FOR ROOM TEMPERATURE SENSING IN HEATING MODE AS WELL AS SETPOINT

ADJUSTMENT FOR HEATING AND COOLING. PROVIDE WITH OPTIONAL BACNET INTERFACE.

7. REGISTER SHALL HAVE AIR SCOOP.

8. PROVIDE A SINGLE BALANCING REMOTE TO ALLOW ADJUSTMENT TO THE VAV DIFFUSER MINIMUM AND MAXIMUM SET POINTS. REMOTE SHALL GIVEN TO OWNER UPON COMPLETION OF PROJECT.

9. ADJUST BLADES TO THROW AIR DOWNWARD AT 20 DEGREES DIFFERENTIAL.

ROOF-TOP AIR CONDITIONING, HEATING & VENTILATING UNIT - GAS FIRED SCHEDULE

MINIMUM MINIMUM COOLING CAPACITY AT ENTERING CONDITIONS SHOWN HEATING DATA ELECTRICAL DATA

MARK CFM OUTSIDE ESP TOTAL CAP SENS. CAP EAT DB/WB LAT DB AMB. AIR INPUT OUTPUT EAT DB LAT DB V PH MCA MAX FUSE BASIS OF DESIGN MECH

AIR (IN WG) (MBH) (MBH) (°F) (°F) ENT. COND. (F) (MBH) (MBH) (°F) (°F) AMPS NOTES

RTU-C1 2000 675 0.8 77.1 57.7 85/70 55 95 160 128.0 30.0 90.0 480 3 14.8 20 DAIKIN DPS006A 1 THRU 7




RTU-F1 2500 1250 0.5 60.9 44.9 85/71 55 95 120 96 56.0 93.0 480 3 32.1 40 DAIKIN DPS005A 1 THRU 8

MECHANICAL NOTES:

1. EXTERNAL STATIC PRESSURE AS SHOWN IS EXTERNAL TO THE UNIT AND IS THE STATIC PRESSURE AVAILABLE FOR DUCTWORK AND ACCESSORIES.

TOTAL STATIC PRESSURE = EXTERNAL + INTERNAL STATIC PRESSURE. DESIGN FOR MID-LIFE PRESSURE DROP FOR FILTER LOADING. THIS IS IN ADDITION TO THE

CLEAN FILTER PRESSURE DROP.

2. ALL SECTIONS (FIELD OR FACTORY FABRICATED) OF THE AIR HANDLING UNIT SHALL BE DOUBLE WALL INSULATED AS PER THE SPECIFICATIONS.

3. PROVIDE ACCESS DOORS IN ALL FILTER, ACCESS AND FAN MODULES.

4. PROVIDE DOUBLE WALL DRAIN PANS UNDER ALL COIL MODULES OR SECTIONS.

5. DAMPERS LOCATED IN THE MIXING BOX / ECONOMIZER MODULE SHALL BE PROVIDED BY THE AHU MANUFACTURER. SEE SPECIFICATIONS.

6. PROVIDE WITH MODULATING HOT-GAS REHEAT WITH A SPACE HUMIDITY SENSOR.

7. RTU CONTROLS SHALL BE A SINGLE-ZONE VARIABLE-AIR-VOLUME CONFIGURATION.

8. RTU PROVIDED WITH INTEGRAL ENERGY RECOVERY WHEEL

SUMMER OPERATION WHEEL DATA: EAT 95° Fdb, 76°Fwb; LAT 78° Fdb, 67.3°Fwb / CAPACITY - 40 MBH / EFFECTIVENESS - 0.64 TOTAL, 0.67 SENSIBLE

WINTER OPERATION WHEEL DATA: EAT -8° Fdb, -8°Fwb; LAT 42.5° Fdb, 33.8°Fwb / CAPACITY - 78 MBH / EFFECTIVENESS - 0.66 TOTAL, 0.67 SENSIBLE

WHEEL DATA: AIRSIDE PD - 0.58" H20 / FACE VELOCITY MAX - 700 FPM / PREFILTER - 2" MERV 8

AIR SEPERATOR - HYDRONIC PIPING AIR CONTROL DEVICE

PRESS. DIMENSIONS DRY

MARK LOCATION SERVES FLOW DROP (DIA. x H) WEIGHT BASIS OF DESIGN MECH

(GPM) (FT.W.G.) (IN. x IN.) (LBS.) NOTES

AS-F01 F246 HEAT PUMP LOOP 225 1 12" x 22" 80 TACO - HIGH VELOCITY 4904ADH-125

HEAT PUMP SCHEDULE

MARK

NO. ARRANGEMENT LOCATION REFRIG.

OUTSIDE

AIRFLOW

(CFM)

DOAS

SERVED

BY

TOTAL

AIRFLOW

(CFM)

MIN. ESP

(IN WG)

WATER

FLOW

(GPM)

PRESS.

DROP

(FT WAT)

COOLING DATA HEATING DATA ELECTRICAL DATAUNIT

WEIGHT

(LB)

MANUFACTURER MODEL

NUMBEREAT DB

(DEG F)

EAT WB

(DEG F)

LAT DB

(DEG F)

TOTAL

CAP

(MBTUH)

SENS

CAP

(MBTUH)

HEAT

REJ

(BTUH)EER

COOLING

EWT

(DEG F)

COOLING

LWT

(DEG F)

EAT DB

(DEG F)

EAT WB

(DEG F)

TOTAL

CAP

(MBTUH)

HEAT

ABS

(MBTUH)COP

HEATING

EWT

(DEG F)

HEATING

LWT

(DEG F)

V/PH

MIN

CIRC

AMPS

FULL

LOAD

AMPS

MOTOR

TYPE

MAX

FUSE

AMPS

HP-F01 HORIZONTAL SEE PLANS R-410A 250 DOAS-F01 380 0.5 3.00 9.95 75.0 63.0 54.7 11.3 8.5 14,411 12.5 90 99.6 75.0 63.0 11.2 8.3 3.8 40.0 34.5 208/1 6.8 5.6 ECM 15 154 DAIKIN WGSH0121

HP-F02 HORIZONTAL SEE PLANS R-410A 250 DOAS-F01 500 0.5 3.75 6.04 75.0 63.0 57.2 14.2 11 17,482 14.7 90 99.3 75.0 63.0 13.6 10.4 4.1 40.0 34.5 208/1 10.0 8.4 ECM 15 200 DAIKIN WGSH0151




HP-F06 HORIZONTAL SEE PLANS R-410A 250 DOAS-F01 800 0.5 6.00 5.36 75.0 63.0 54.0 24.3 19 29,901 14.7 90 100.0 75.0 63.0 20.8 15.8 3.7 40.0 34.6 460/3 7.0 6.1 ECM 15 254 DAIKIN WGTH0261


HP-F08 HORIZONTAL SEE PLANS R-410A 200 DOAS-F01 500 0.5 3.75 3.89 75.0 63.0 57.2 14.0 10.9 17,338 14.2 90 99.2 75.0 63.0 13.3 10 4.1 40.0 34.5 208/1 10.0 8.4 ECM 15 200 DAIKIN WGSH0151


HP-F10 HORIZONTAL SEE PLANS R-410A 300 DOAS-F01 1225 0.5 10.5 5.04 75.0 63.0 53.8 41.1 29.5 50,787 14.5 90 99.7 75.0 63.0 3.6 27.2 4 40.0 34.7 460/3 13.3 11.7 ECM 15 365 DAIKIN WGTH0441

HP-F11 HORIZONTAL SEE PLANS R-410A 100 DOAS-F01 900 0.5 6 5.36 75.0 63.0 54.9 24.6 20.3 30,350 14.7 90 100.1 75.0 63.0 21 16 4.1 40.0 34.8 460/3 7.0 6.1 ECM 15 254 DAIKIN WGTH0261

HP-F13 HORIZONTAL SEE PLANS R-410A 200 DOAS-F02 700 0.5 6 5.36 75.0 63.0 53.8 23.9 17.7 29,452 14.8 90 99.8 75.0 63.0 20.6 15.6 4 40.0 34.7 460/3 7.0 6.1 ECM 15 254 DAIKIN WGTH0261


HP-F15 HORIZONTAL SEE PLANS R-410A 200 DOAS-F02 700 0.5 6 5.36 75.0 63.0 57.2 23.9 17.7 29,452 14.8 90 99.8 75.0 63.0 20.6 15.6 4.1 40.0 34.5 460/3 7.0 6.1 ECM 15 254 DAIKIN WGTH0261



HP-F18 HORIZONTAL SEE PLANS R-410A 270 DOAS-F02 800 0.5 6 5.36 75.0 63.0 53.8 24.3 19 29,901 14.7 90 100 75.0 63.0 20.8 15.8 4.1 40.0 34.8 460/3 7.0 6.1 ECM 15 254 DAIKIN WGTH0261




HP-F22 HORIZONTAL SEE PLANS R-410A 100 DOAS-F01 1000 0.5 7.5 8.03 75.0 63.0 55.9 29.6 22 37,116 13.5 90 99.9 75.0 63.0 27 20.3 4.1 40.0 35.0 460/3 9.5 8.4 ECM 15 256 DAIKIN WGTH0321




GENERAL NOTES

1. MANUFACTURER SHALL PROVIDE ANY TOOLS OR PROGRAMMING NECESSARY FOR FIELD BALANCING OF HEAT PUMP FAN SPEEDS.

MECHANICAL NOTES:

1. PERFORMANCE MUST MEET THE MINIMUM REQUIREMENTS OF AHRI/ISO STANDARD 13256-1 FOR WATER SOURCE HEAT PUMPS. SCHEDULED EER AND COP IS BASED ON OPERATING CONDITIONS.

2. CAPACITY AND PRESSURE DROP ARE BASED ON A 60% WATER, 40% PROPYLENE GLYCOL SOLUTION. ESP AS SHOWN IS EXTERNAL TO THE UNIT WITH A CLEAN FILTER IN PLACE.

3. PROVIDE TWO COMPLETE SETS OF AIR FILTERS FOR EACH UNIT. ONE SET FOR CONSTRUCTION, ONE SET FOR CHANGE-OUT PRIOR TO AIR BALANCING. AIR FILTERS SHALL BE 2" MERV 8 PLEATED FILTERS, IN STANDARD AVAILABLE

SIZES PER THE SPECIFICATIONS.

4. CASING SHALL COME COMPLETE WITH SUPPLY AND RETURN DUCT COLLAR CONNECTIONS.

5. PROVIDE HANGER KITS FOR HORIZONTAL UNITS. KIT SHALL CONSIST OF STEEL BRACKETS, BOLTS, WASHERS, VIBRATION ISOLATORS AND ALL THREADED RODS.

HP-F12 HORIZONTAL SEE PLANS R-410A 100 DOAS-F01 900 0.5 6 5.36 75.0 63.0 54.9 24.6 20.3 30,350 14.7 90 100.1 75.0 63.0 21 16 4.1 40.0 34.8 460/3 7.0 6.1 ECM 15 254 DAIKIN WGTH0261

Arc

hite

ctu

re E

ngin

eering

P

lan

nin

g In

teriors

©

,

DL

R G

rou

p inc., a

Ne

bra

ska

co

rpo

ratio

n, A

LL

RIG

HT

S R

ES

ER

VE

D

Rev

isio

ns

9/2

2/2

017 2

:54:0

7 P

M

C:\R

evit\1

0-1

3125-3

0_M

P_2016_C

entr

al_

mm

art

z.r

vt

10-1

3125-3

0

8/2

9/2

017

PLA

TT

EV

IEW

JR

HIG

H &

HIG

H S

CH

OO

L R

EN

OV

AT

ION

S

ME

CH

AN

ICA

L S

CH

ED

ULE

SM

5.1

20

17

SP

RIN

GF

IELD

PLA

TT

EV

IEW

CO

MM

UN

ITY

SC

HO

OLS

CC

-29/

20/1

7A

DD

EN

DU

M C

C-2

CC-2

DEDICATED OUTDOOR AIR SYSTEM - GAS FIRED SCHEDULE

MINIMUM MINIMUM COOLING CAPACITY AT ENTERING CONDITIONS SHOWN HEATING DATA ELECTRICAL DATA

MARK CFM OUTSIDE ESP TOTAL CAP SENS. CAP EAT DB/WB LAT DB AMB. AIR INPUT OUTPUT EAT DB LAT DB V PH MCA MAX FUSE BASIS OF DESIGN MECH

AIR (IN WG) (MBH) (MBH) (°F) (°F) ENT. COND. (F) (MBH) (MBH) (°F) (°F) AMPS NOTES

DOAS-F1 3500 3500 0.8 146.9 90.4 78.5/67.6 54 95 300 240.0 39.6 102.1 460 3 59.9 70 DAIKIN DPS012A 1 THRU 7

DOAS-F2 3700 3700 0.8 148.9 93.5 78.8/67.8 55 95 300 240.0 39.6 102.1 460 3 59.9 70 DAIKIN DPS012A 1 THRU 7

MECHANICAL NOTES:

1. EXTERNAL STATIC PRESSURE AS SHOWN IS EXTERNAL TO THE UNIT AND IS THE STATIC PRESSURE AVAILABLE FOR DUCTWORK AND ACCESSORIES.

TOTAL STATIC PRESSURE = EXTERNAL + INTERNAL STATIC PRESSURE. DESIGN FOR MID-LIFE PRESSURE DROP FOR FILTER LOADING. THIS IS IN ADDITION TO THE

CLEAN FILTER PRESSURE DROP.

2. ALL SECTIONS (FIELD OR FACTORY FABRICATED) OF THE AIR HANDLING UNIT SHALL BE DOUBLE WALL INSULATED AS PER THE SPECIFICATIONS.

3. PROVIDE ACCESS DOORS IN ALL FILTER, ACCESS AND FAN MODULES.

4. PROVIDE DOUBLE WALL DRAIN PANS UNDER ALL COIL MODULES OR SECTIONS.

5. DAMPERS LOCATED IN THE MIXING BOX / ECONOMIZER MODULE SHALL BE PROVIDED BY THE AHU MANUFACTURER. SEE SPECIFICATIONS.

6. PROVIDE WITH MODULATING HOT-GAS REHEAT WITH A SPACE HUMIDITY SENSOR.

7. RTU CONTROLS SHALL BE A SINGLE-ZONE VARIABLE-AIR-VOLUME CONFIGURATION.

8. RTU PROVIDED WITH INTEGRAL ENERGY RECOVERY WHEEL.

EXPANSION TANK SCHEDULE

MAX SYSTEM MAX. ALLOWABLE TANK ACCEPTANCE MECH

MARK SERVES TEMP VOLUME PRESSURE VOLUME VOLUME BASIS OF DESIGN NOTES

(ET-X) (°F) (GAL) (PSI) (GAL) (MIN) (GAL) (MIN)

ET-F01 GDWH-1 140 8 150 20 3.2 AMTROL MODEL ST-20VC 1

ET-F02 HEAT PUMP LOOP 115 6000 125 67 34 TACO CBX-254 1,2

MECHANICAL NOTES:

1. ASME CONSTRUCTION

2. SYSTEM VOLUME IS ESTIMATED

SUMP PUMP SCHEDULE

MOTOR DATA BASIN DATA

PUMP MINSIZE MECH

MARK SERVES LOCATION PUMP TYPE GPM HEAD EFF HP V PH HZ RPM MATERIAL DIA X DEPTH BASIS OF DESIGN NOTES

(SP-X) (EACH PUMP) (FT WG) (%) (IN)

SP-1 UNDERFLOOR SUBDRAINAGE F114 SIMPLEX SUBMERSIBLE 5 15 - 1/6 115 1 60 3450 FIBERGLASS 24" x 30" ZOELLER MODEL 42 SERIES 1, 2

SP-2 UNDERFLOOR SUBDRAINAGE F104 SIMPLEX SUBMERSIBLE 50 32 - 1/2 115 1 60 3450 EXISTING - ZOELLER MODEL 6292 1, 2

SP-3 UNDERFLOOR SUBDRAINAGE F109 SIMPLEX SUBMERSIBLE 50 32 - 1/2 115 1 60 3450 EXISTING - ZOELLER MODEL 6292 1, 2

MECHANICAL NOTES:

1. PROVIDE WITH AUTOMATIC FLOAT SWITCH.

2. PUMP SHALL HAVE 2-INCH DISCHARGE, AND 10 FOOT ELECTRICAL CORD WITH STANDARD GROUNDED PLUG.

TANK SCHEDULE

TANK SIZE

MARK LOCATION APPLICATION CAPACITY DIA HEIGHT MOUNTING BASIS OF DESIGN MECH

(GAL) (IN) (IN) NOTES

T-1 F103 HOT WATER 200 32 77 FLOOR AO SMITH MODEL TJV-200-M

NT F114 ACID NEUTRALIZATION 55 23.5 36 RECESSED BELOW FLOOR ENFIELD MODEL EZ0055 1

MECHANICAL NOTES:

1. 500 LBS LIMESTONE CHIPS

THERMOSTATICE MIXING VALVE SCHEDULE

PRESSURE COLD WATER HOT WATER HOT WATER RECIRC HOT WATER PUMP

MARK LOCATION SERVES APPLICATION LWT CAPACITY DROP INLET INLET INLET OUTLET MOUNTING MARK NO. BASIS OF DESIGN MECH

(ETMV-X / TMV-X) (°F) (GPM) (PSIG) (INCHES) (INCHES) (INCHES) (INCHES) NOTES

ETMV-1 F111 EEWS-1 EMERGANCY 60-100 1 - 31 30 1" 1" - 1-1/4" AT CEILING - HAWS MODEL 9201H

TMV-1 F103 BUILDING DOMESTIC HOT WATER 110 1 - 48 15 1" 1" 3/4" 1-1/4" WALL EXIST. LEONARD MEGATRON MODEL 3NB-LF 1, 2

TMV-2 F239 LAV KITCHEN 110 2.5 10 1/2" 1/2" - 1/2" UNDER LAV - LEONARD MODEL 170A-LF

MECHANICAL NOTES:

1. MOUNTING HEIGHT IS A MINIMUM OF 36-INCHES TO THE BOTTOM OF THE UNIT TO A MAXIMUM OF 60-INCHES TO THE TOP OF THE OUTLET.

2. PROVIDE PIPING METHOD #2 PER MANUFACTURERS RECOMMENDATIONS.

DOMESTIC WATER HEATER - GAS FIRED SCHEDULE

EXPANSIONELECTRICAL DATA

TANK TANK MINIMUM OPERATING MECH

MARK LOCATION CAPACITY MARK RECOVERY EWT LWT INPUT HP V PH HZ WT BASIS OF DESIGN NOTES

(DWH-X) (GAL) (ET-XX) (GAL/HR) (°F) (°F) (MBH) [WATTS] (LBS)

GDWH-1 F103 100 ET-1 235 40 140 199 5.0 AMPS 120 1 60 1388 AO SMITH MODEL BTH-199 (A 1

MECHANICAL NOTES:

1. WATER HEATER SHALL INCLUDE ASME RATED TEMPERATURE AND PRESSURE RELIEF VALVE AND DRAIN VALVE.

UNIT HEATER - ELECTRIC

ELECTRIC COIL DATA ELECTRICAL DATA

MOUNTING MECH

MARK LOCATION CFM KW MBH V PH Hz AMPS HEIGHT BASIS OF DESIGN NOTES

(UH-X) (FT)

UH-1 A201 350 3 10.2 208 1 60 14.5 8'-0" AFF QMARK MUH03-81 1,2,3

MECHANICAL NOTES:

1. PROVIDE LOUVER FIN DIFFUSER FOR THROW ADJUSTMENT.

2. PROVIDE INTEGRAL DISCONNECT SWITCH AND 24 VOLT LOW VOLTAGE CONTROL. WALL THERMOSTAT BY CONTROLS CONTRACTOR.

3. PROVIDE HEATER BRACKET.

SPLIT SYSTEM CONDENSING UNIT

TOTAL COMPRESSOR DATA CONDENSER DATA ELECTRICAL DATA

MARK CAPACITY NO STEPS REFRIG FAN FAN NO AMB TEMP V PH MCA MOCP BASIS OF DESIGN MECH

(MBH) (EACH) TYPE NO FLA CIRC (°F) NOTES

CU-C1 14.0 1 INFINITE R-401A 1 0.50 1 105 208 1 12.0 15.0 MITZSUBISHI MUY-GE15NA 1 THRU 5

CU-C2 17.2 1 INFINITE R-401A 1 0.93 1 105 208 1 14.0 15.0 MITZSUBISHI MUY-GE18NA 1 THRU 5

CU-F1 17.2 1 INFINITE R-401A 1 0.93 1 105 208 1 14.0 15.0 MITZSUBISHI MUY-GE18NA 1 THRU 5

MECHANICAL NOTES:

1. COOLING ONLY APPLICATION. TOTAL CAPACITY BASED ON INDOOR UNIT FAN SPEED ON HIGH.

2. REFRIGERANT PIPE QUANTITIES AND SIZE TO BE PER MANUFACTURER'S PIPING RECOMMENDATIONS AND SPECIFICATION SECTION 238126.

3. PROVIDE WITH THE FOLLOWING:

A. LOW AMBIENT KIT FOR OPERATION DOWN TO -10 DEG. F.

B. WINTER START CONTROL RELAY TO BYPASS LOW PRESSURE SWITCH TO PERMIT START-UP FOR COOLING OPERATION UNDER LOW LOAD CONDITIONS

AT LOW AMBIENT TEMPERATURES.

C. CRANKCASE HEATER THAT CLAMPS ONTO THE COMPRESSOR OIL SUMP.

D. WIND BAFFLE TO IMPROVE UNIT OPERATION DURING HIGH WINDS AND FOR LOW AMBIENT CONDITIONS.

4. UNIT TO BE MOUNTED ON EQUIPMENT RAILS. SEE 230529 FOR DESCRIPTION. MOUNTING EQUIPMENT ON 4 x 4 LUMBER DIRECTLY ON ROOF IS NOT ACCEPTABLE.

5. INDOOR UNIT IS POWERED FROM OUTDOOR UNIT. MCA TOTAL IS COMBINED FOR OUTDOOR UNIT AND INDOOR UNIT.

SPLIT SYSTEM INDOOR UNIT

COOLING DATA FAN DATA ELECTRICAL DATA

CONDENSING TOT EAT CONDENSATE

MARK UNIT LOCATION CAP DB / WB CFM MOTOR V PH Hz MCA MOP BASIS OF DESIGN MOUNTING HEIGHT DRAIN SIZE MECH

(MBH) (°F) (FLA) (BOTTOM OF UNIT) (INCHES) NOTES

AC-C1 CU-C1 C228 14.0 75 / 60 385 0.76 208 1 60 1 - MITZSUBISHI MSY-GE15NA 7'-0" 3/4" 1 THRU 7

AC-C2 CU-C2 C221 17.2 75 / 60 420 0.76 208 1 60 1 - MITZSUBISHI MSY-GE18NA 10'-0" 3/4" 1 THRU 7

AC-F1 CU-F1 F113 17.2 75 / 60 420 0.76 208 1 60 1 - MITZSUBISHI MSY-GE18NA 10'-0" 3/4" 1 THRU 7

MECHANICAL NOTES:

1. DUCTLESS SYSTEM, COOLING ONLY APPLICATION. MOUNT PER MANUFACTURER'S INSTRUCTIONS.

2. MOUNTING HEIGHT SHOWN IS A MINIMUM, TO FACILITATE CONDENSATE DRAINAGE. FINAL HEIGHT MAY BE HIGHER TO ACCOMMODATE CLEARANCES OR FACILITATE ATTACHMENT TO STRUCTURE.

3. EACH UNIT SHALL BE PROVIDED WITH A WIRED WALL MOUNTED CONTROLLER (MITSUBISHI PAR-31MAA).

4. 24 VOLT CONTROL VOLTAGE.

5. MINIMUM SEER RATING SHALL BE 13.0 TO MEETING ENERGY CODE. EQUIPMENT SELECTED BELOW THIS RATING WILL NOT BE ACCEPTED.

6. INDOOR UNIT IS POWERED FROM OUTDOOR UNIT. MCA SHOWN IS FOR INDOOR UNIT ONLY. SEE SPLIT SYSTEM OUTDOOR UNIT SCHEDULE FOR TOTAL CONNECTED MCA AND MOP LOAD.

7. EACH UNIT SHALL BE PROVIDED WITH A CONDENSATE PUMP AND DISCONNECT SWITCH.

PLUMBING FIXTURE CONNECTION SCHEDULE

FIXTURE CONNECTIONS

MARK FIXTURE CW HW TEMPERED WATER WASTE VENT REMARKS

CS-1 COUNTER SINK 1/2" 1/2" - 1-1/2" 1-1/2" COUNTER-TOP MOUNTED

CS-2, 3 COUNTER SINK - ADA 1/2" 1/2" - 1-1/2" 1-1/2" COUNTER-TOP MOUNTED

EWC-1 ELECTRIC WATER COOLER 1/2" - - 1-1/4" 1-1/4" 34" TO RIM

EWC-2 ELECTRIC WATER COOLER - ADA 1/2" - - 1-1/4" 1-1/4" 36" TO SPOUT

EWC-3 ELECTRIC WATER COOLER 1/2" - - 1-1/4" 1-1/4" 31" TO ADA SPOUT

EEWS-1 EMERGENCY EYEWASH/ - - 1/2" TO EYEWASH 1-1/4" TO 1-1/4" TO 34" TO TOP OF FLOW HEADS FOR EYEWASH

SHOWER, ADA COMPLIANT 1" TO SHOWER EYEWASH EYEWASH SHOWER HEAD MTD IN CEILING

IMF-1 ICE MACHINE FITTING 1/2" - - - - 42" A.F.F.

L-1 LAVATORY 1/2" 1/2" - 1-1/4" 1-1/4" 30" TO RIM

L-2 LAVATORY, ADA COMPLIANT 1/2" 1/2" - 1-1/4" 1-1/4" 34" TO RIM

L-3 LAVATORY 1/2" 1/2" - 1-1/4" 1-1/4" 28" TO RIM

L-4 LAVATORY, ADA COMPLIANT 1/2" 1/2" - 1-1/4" 1-1/4" 31" TO RIM

MS-1 MOP SINK 1/2" 1/2" - 3" SEE PLANS FLOOR MOUNTED

SH-1 SHOWER, INDIVIDUAL 1/2" 1/2" - - - 84" TO HEAD

SH-2 SHOWER, INDIVDUAL - ADA 1/2" 1/2" - - - CONTROL VALVE AREA TO BE

38" TO 48" AFF,

84" TO HEAD

UR-1 URINAL 3/4" - - 2" 1-1/2" 24" TO RIM

UR-2 URINAL, ADA COMPLIANT 3/4" - - 2" 1-1/2" 17" TO RIM

WMF-1 WASHING MACHINE FITTING 1/2" 1/2" - 2" 1-1/2" 42" TO RIM

WC-1 WATER CLOSET 1" - - 4" 2" 15" TO RIM

WC-2 WATER CLOSET - ADA 1" - - 4" 2" 17" TO TO RIM

WC-3 WATER CLOSET 1" - - 4" 2" 15" TO RIM

WC-4 WATER CLOSET - ADA 1" - - 4" 2" 16" TO TO RIM

RH-1 WALL HYDRANT 3/4" - - - - ROOF MOUNTED Arc

hite

ctu

re E

ngin

eering

P

lan

nin

g In

teriors

©

,

DL

R G

rou

p inc., a

Ne

bra

ska

co

rpo

ratio

n, A

LL

RIG

HT

S R

ES

ER

VE

D

Revis

ions

9/2

2/2

017 2

:59:5

3 P

M

C:\R

evit\1

0-1

3125-3

0_M

P_2016_C

entr

al_

mm

art

z.r

vt

10-1

3125-3

0

8/2

9/2

017

PLA

TT

EV

IEW

JR

HIG

H &

HIG

H S

CH

OO

L R

EN

OV

AT

ION

S

ME

CH

AN

ICA

L S

CH

ED

ULE

SM

5.2

20

17

SP

RIN

GF

IELD

PLA

TT

EV

IEW

CO

MM

UN

ITY

SC

HO

OLS

CC

-29

/20/1

7A

DD

EN

DU

M C

C-2

CC-2

GG

HH

WW

II II

XX

JJ

KK

12 14 15 16

X

Y

Z

4" SD UP

4" SD UP

3"3" SD

4"4" SD

4"4" SD

3"3" S

D

5"5" SD

4"4" SD

4"4" SD

3"3" S

D

3"3" SD

5"5" SD 6"6" SD

4"4" S

D

4"4" SD

4" SD UP

5"5" SD

2" W UPTO TD

2" W UP TO LAV

2" V UP

3" SD UP

4" W UPTO WC4" 7 WFU4" W 7 WFU

2" W

JH BOYSLOCKER ROOM

C203

MALECOACHES

OFFICE

C206

COLLABORATIONROOM

C207

TOILET/SHOWER

C208

HS BOYSLOCKER ROOM

C209

BOYSSHOWERS

C205

GIRLSSHOWERS

C214

FEMALECOACHES

OFFICE

C215

?

?

PE STORAGE

C202

PE STORAGE

C201

HS GIRLSLOCKER ROOM

C218

ELECTRICAL

C221

STORAGE

C222

TOILET/SHOWER

C217

COLLABORATIONROOM

C216JAN

C220

2" W UPTO TD

2" W UP TO LAV

2" V UP

3" SD UP3" W UPTO WC

2" W

2" V UP

2" W UPTO FD

2" W UPTO FD

2" W UPTO LAV

2" W UPTO LAV

2" 4 WFU2" W 4 WFU

2" 8 WFU2" W 8 WFU

4" 36 WFU4" W 36 WFU

4" W UP(28 WFU)

4"4" W

4"4" W

4" W UP TOFCO-EX

3"3" W

4"4" W

4"4" W

3" E

XIS

T.

3" W

EX

IST

.3"3"

W4"4"

W4"4"

W4"4"

W

3" W UP TOFCO-EX

4" W UP (36 WFU)

2" W UPTO LAV

2" W UPTO LAV

2" V UP

2" W UPTO FD

2" W UPTO FD

2" OFFSET W UPTO TD (TYP 2)TO MISS FTG.

2" 2

WF

U2"

W 2

WF

U2"

2 W

FU

2" W

2 W

FU

2"2" W

2"2" W

2" W UPTO FCO

3" W UP TOFCO-EX

4" W UP TOFCO-EX

3" 7 WFU3" W 7 WFU

2" W UPTO FCO

2" V UP (TYP 12)

TRAPPRIMER

TRAPPRIMER

3" E

XIS

T.

3" W

EX

IST

.

3" 3 WFU3" W 3 WFU

2" V UP

3" W UPTO MS-1

2" W UPTO TD(TYP 10)

4" W

2" W

PLUMBING GENERAL NOTES

1. FOR PIPE SIZES TO INDIVIDUAL FIXTURES, SEE THEPLUMBING FIXTURE CONNECTION SCHEDULE ON SHEETM5.2.

2. INVERT ELEVATIONS ARE BASED ON A FINISHED FLOORELEVATION OF 100’.

3. RUN BRANCH MAINS FULL SIZE THE ENTIRE LENGTH OF THECHASEAND BRANCH OFF TO FIXTURES WITH SIZES PER THEPLUMBING FIXTURE CONNECTION SCHEDULE.

4. VALVES SHALL BE LOCATED ABOVE ACCESSIBLE CEILINGS. IFTHIS IS NOT POSSIBLE, ACCESS PANELS SHALL BEPROVIDED. ACCESS PANELS SHALL BE TAMPER PROOFLOCKABLE ACCESS PANELS FOR ACCESS TOALL PLUMBING VALVES THAT ARE NOT LOCATED OVER ANACCESSIBLE CEILING.

Arc

hite

ctu

re E

ngin

eering

P

lan

nin

g In

teriors

©

,

DL

R G

rou

p inc., a

Ne

bra

ska

co

rpo

ratio

n, A

LL

RIG

HT

S R

ES

ER

VE

D

KEY PLAN


A

NO

RT

H

Rev

isio

ns

B

C

D

E

F

9/2

2/2

017 2

:54:2

1 P

M

C:\R

evit\1

0-1

3125-3

0_M

P_2016_C

entr

al_

mm

art

z.r

vt

10-1

3125-3

0

8/2

9/2

017

PLA

TT

EV

IEW

JR

HIG

H &

HIG

H S

CH

OO

L R

EN

OV

AT

ION

S

UN

DE

RG

RO

UN

D P

LU

MB

ING

PLA

N, M

AIN

LE

VE

L -

AR

EA

CP

0.1

C

20

17

SP

RIN

GF

IELD

PLA

TT

EV

IEW

CO

MM

UN

ITY

SC

HO

OLS


UNDERGROUND PLUMBING PLAN, MAIN LEVEL - AREA C

CC

-29/

20/1

7A

DD

EN

DU

M C

C-2

CC-2

DN

A B C

D

E F G H J K

1

2

3

4 5

6

7

8

9

10

11

GYMNASIUM

F244

KITCHEN

F239

STORAGE

F240

VEST

F247

OFFICE

F234STORAGE

F245

CLASSROOM

F233

GIRLS

F243

BOYS

F242

ELECTRICAL

F238

COORIDOR

F241

VEST

F201

EARLYEDUCATION

F202

EARLYEDUCATION

F203BOYS

F204

GIRLS

F205

BOYS

F213

GIRLS

F214

PRINCIPAL

F207

NURSE

F209

WORK ROOM

F211

GUIDANCE

F208

CLASSROOM

F222

CLASSROOM

F221

SPECIAL ED

F230

JANITOR

F216

CLASSROOM

F228

TEACHERSLOUNGE

F220

WOMENS

F217

MENS

F218CLASSROOM

F229

SCIENCE

F223

CONFERENCEROOM

F225

ELEC

F224

TOILET

F210

RECEPTION

F206

LEARNINGCOMMONS

F232

CORRIDOR

F212

ALCOVE

F236

CORRIDOR

F215

COORIDOR

F227

CORRIDOR

F219

OFFICE

F231

JANITOR

F237

STORAGE

F226

OFFICE

F235

P2.2

4

P2.2

5

P2.2

3

P2.2

6

EWC-2 EWC-1

1 1/2" 1 VFU1 1/2" V 1 VFU

1/2" CW, 1-1/2" V& 2" W DN

3/4" EXIST.3/4" CW EXIST.3/4" EXIST.3/4" CW EXIST.

WCO

5"5" SD

5" EXIST.5" SD EXIST.


DOAS-F1

DOAS-F2ON ROOF

ON ROOF

ON ROOFRTU-F1

3/4" OFFSET GAS UP

3/4"

120

MB

H O

N R

OO

F3/

4" G

as 1

20 M

BH

ON

RO

OF

3/4"

120

MB

H O

N R

OO

F3/

4" G

as 1

20 M

BH

ON

RO

OF

3/4" 120 MBH ON ROOF3/4" Gas 120 MBH ON ROOF



3/4" 420 MBH ON ROOF3/4" Gas 420 MBH ON ROOF1" 750 MBH ON ROOF1" Gas 750 MBH ON ROOF

POUNDS TO INCHESREGULATOR ON ROOF

3/4" GAS DN(30 MBH)

GAS METER ENTRANCE TOTALBUILDING LOAD OF 950 MBH +EMERGENCY GENERATOR 260MBH AT 2 LBS

1/2"1/2" 140-HWC 1 1/2"1 1/2" 140-HW

140 HW & HWC OFFSETDN AS NEEDED

ROUTE AS HIGHAS POSSIBLE

ROUTE AS HIGHAS POSSIBLE

PROVIDE NEW SINGLE FIXTURETHERMOSTATIC MIXING VALVETMV-2 UNDER EXISTING LAVATORY.SET TEMP. TO 110 DEGREES MAX.

1/2" EXIST.1/2" 140-HWC EXIST.

1 1/2" EXIST.1 1/2" 140-HW EXIST.

1" EXIST.1" CW EXIST.

EMERGENCYGAS POWERGENERATOR260 MBH

3/4" GAS DN& TO METER

3/4" RH-1ON ROOF

1/2" DRAIN FROM ROOFHYDRANT TO MOP SINK

3/4"

3 C

FU

3/4"

CW

3 C

FU

3/4" 2.5 CFU3/4" CW 2.5 CFU


GM

5

M4.2

3/4" RH-1ON ROOF

4

M4.2

3/4"

330

MB

H O

N R

OO

F3/

4" G

as 3

30 M

BH

ON

RO

OF






Arc

hite

ctu

re E

ngin

eering

P

lan

nin

g In

teriors

©

,

DL

R G

rou

p inc., a

Ne

bra

ska

co

rpo

ratio

n, A

LL

RIG

HT

S R

ES

ER

VE

D

KEY PLAN


A

NO

RT

H

Rev

isio

ns

B

C

D

E

F

9/2

2/2

017 2

:54:3

0 P

M

C:\R

evit\1

0-1

3125-3

0_M

P_2016_C

entr

al_

mm

art

z.r

vt

10-1

3125-3

0

8/2

9/2

017

PLA

TT

EV

IEW

JR

HIG

H &

HIG

H S

CH

OO

L R

EN

OV

AT

ION

S

PLU

MB

ING

PLA

N, M

AIN

LE

VE

L -

AR

EA

FP

1.2

F

20

17

SP

RIN

GF

IELD

PLA

TT

EV

IEW

CO

MM

UN

ITY

SC

HO

OLS


PLUMBING PLAN, MAIN LEVEL - AREA F

CC

-29/

20/1

7A

DD

EN

DU

M C

C-2

CC-2

CC-2

CC-2

WW

II

XX

12 14 15

EWC-2

EWC-1

UR-2 UR-1 UR-1WC-1 WC-2

WC-2

2" FD-1

WC-1WC-1WC-1WC-1

2" FD-1

L-2 L-1

L-2 L-1

2" TD-1 2" TD-1

2" TD-1 2" TD-1

2" TD-1

SH-2

SH-2

2" TD-1 2" TD-1

2" TD-1

2" T

D-1

2" T

D-1

2" TD-1

2" TD-1

SH-1

SH-1SH-1

SH-1

SH-1 SH-1SH-1SH-1

SH-1 SH-1

WCO

2" 7

VF

U2"

V 7

VF

U

FCOEXIST.FCO

WCO

PE STORAGE

C202

PE STORAGE

C201BOYS

SHOWERS

C205

GIRLSSHOWERS

C214

4" RD-EX

EXIST.FCO

2" 7

VF

U2"

V 7

VF

U

2 1/2" 31 VFU2 1/2" V 31 VFU

2-1/2" V UP (38 VFU)TO EXIST. 4" VTR-EX

2" V

2" V DN (TYP 12)

2" V DN

TRAP PRIMER

4" V UP (40 VFU) TOEXIST. 4" VTR

2" V &4 W

2-1/2" V& 4" W

1-1/2" W & V

2" V &4 W

4" W DN (36 WFU)

FCO

D

WATER HAMMER ARRESTER

2" CW

2" CW DN(91.5 CFU)

1/2"

3 C

FU

1/2"

CW

3 C

FU

1/2"

3 C

FU

1/2"

CW

3 C

FU

1" 6 CFU1" CW 6 CFU3/4" HW & CWDN (TYP 5)

1 1/2" 24 CFU1 1/2" CW 24 CFU

1/2" HW & CWDN (TYP 2)

1" 6 HFU1" 110-HW 6 HFU1" 6 HFU1" 110-HW 6 HFU

SET AT0.5 GPM

1/2" 0.5 GPM1/2" 110-HWC 0.5 GPM

1/2" 0.5 GPM1/2" 110-HW 0.5 GPM1/2"

1.5

GP

M1/

2" 1

10-H

WC

1.5

GP

M

2" 1

7 C

FU

2" C

W 1

7 C

FU

1" 4

.5 H

FU

1" 1

10-H

W 4

.5 H

FU

1 1/2" 36 HFU1 1/2" 110-HW 36 HFU

1 1/2" 36 HFU1 1/2" 110-HW 36 HFU

2" 112 CFU2" CW 112 CFU

1" 6 HFU1" 110-HW 6 HFU1" 6 HFU1" 110-HW 6 HFU

2 1/

2" 1

29 C

FU

2 1/

2" C

W 1

29 C

FU

1 1/

2" 4

0.5

1 1/

2" 1

10-H

W 4

0.5

2" 52.5 HFU2" 110-HW 52.5 HFU

1 1/2" 36 CFU1 1/2" CW 36 CFU

1 1/2" 12 CFU1 1/2" CW 12 CFU

1 1/2" 12 HFU1 1/2" 110-HW 12 HFU

2" 91.5 CFU2" CW 91.5 CFU

3/4" 3 HFU3/4" 110-HW 3 HFU

3/4" 3 HFU3/4" 110-HW 3 HFU

1/2" 1.5 HFU1/2" 110-HW 1.5 HFU

3/4" 4.5 HFU3/4" 110-HW 4.5 HFU

EXISTING 3/4" HWCTOILET

C213

TOILET

C204

4" SD UP TOEXIST. 4" RD-EX

1 1/

2" 2

VF

U1

1/2"

V 2

VF

U1

1/2"

2 V

FU

1 1/

2" V

2 V

FU

1/2" 0.5 GPM1/2" 110-HW 0.5 GPM

C2

10

M4.2

4" V DN

3

M4.2

(TYP)

KK

15

TOILET/SHOWER

C208

L-2

SH-2

2" TD-1

WC-2

WCO

WCO

2" 7

VF

U2"

V 7

VF

U2"

6 V

FU

2" V

6 V

FU

3"3" SD

2" V DN &4" W DN

2" V DN

3" SD DNB

WATER HAMMERARRESTER

2" W DN

3/4" HW

1/2" CW

1/2" HW

2" 14.5 CFU2" CW 14.5 CFU

3/4" 4.5 HFU3/4" 110-HWC 4.5 HFU1" CW

1/2" 2.5 CFU1/2" W 2.5 CFU

1/2" W DN FROM RH-1ON ROOF TO DRAININTO TD-1

10

M4.2

(TYP)

Y

Z

L-2 L-1

2" FD-1

WC-2WC-1WC-1

WC-1

UR-2 UR-1UR-1 WC-2

2" FD-1

L-2 L-1

1 1/

2" 2

VF

U1

1/2"

V 2

VF

U1

1/2"

2 V

FU

1 1/

2" V

2 V

FU

2" V

DN

4" W

DN

(28

WF

U)

2" V

& 4

" W

WCO

1-1/2" V

4" W

4" V DN (8 VFU) & UP(36 VFU) TO 4" VTR

C1

2" V

& 4

" W

1" 6 HFU1" 110-HW 6 HFU

1/2"

3 C

FU

1/2"

CW

3 C

FU

3/4"

3 H

FU

3/4"

110

-HW

3 H

FU

3/4" 3 HFU3/4" 110-HW 3 HFU

1/2"

3 C

FU

1/2"

CW

3 C

FU

1/2" 0.5 GPM1/2" 110-HW 0.5 GPM

2" 20 CFU2" CW 20 CFU

D

WATER HAMMER ARRESTER

1/2" 1.5 HFU1/2" 110-HW 1.5 HFU

2" 76 CFU2" CW 76 CFU

2" 70 CFU2" CW 70 CFU

1" 6 CFU1" CW 6 CFU

TRAP PRIMER

TOILET

C210

TOILET

C219

EXISTING 3" GAS

EXISTING 3" GAS

3/4" EXIST. 2.5 CFU3/4" CW EXIST. 2.5 CFU

10

M4.2

(TYP)

3

M4.2

EXIST.FCO

FCO

FCO

EXIST.FCO

4" VTR-EX

2" TD-1(TYP 12)

L-1

L-2

EWC-2

EWC-1

WCO

UR-2

UR-1

UR-1

WCOWC-2

WC-1WC-2

2" FD-1

2" FD-1

WC-1(TYP 4)

4" VTR-C2

L-2

L-12" 7 VFU

2" V 7 VFU

2" 7 VFU

2" V 7 VFU

2" 1

2 V

FU

2" V

12

VF

U

2" 1

2 V

FU

2" V

12

VF

U

4"4" W

3"3" W

4"4" W

3"3" W

2" 2 WFU

2" W 2 WFU

4"4" W

3"3" W

3"3" W

4" 3

6 V

FU

4" V

36

VF

U

1 1/2" 2 VFU

1 1/2" V 2 VFU

1 1/2" 2 VFU

1 1/2" V 2 VFU

2" 2 WFU

2" W 2 WFU

2" 2 VFU2" V 2 VFU

3"3" W

3"3" W

2 1/2" 31 VFU2 1/2" V 31 VFU

2 1/2" 38 VFU2 1/2" V 38 VFU

2"2" W

1 1/2" 2 VFU1 1/2" V 2 VFU4" 36 WFU4" W 36 WFU

1 1/2" 2 WFU1 1/2" W 2 WFU

1 1/2" 2 VFU1 1/2" V 2 VFU

2" 8 VFU2" V 8 VFU

4" 28 WFU4" W 28 WFU

4" 8 WFU4" W 8 WFU

2 1/2" 28 VFU2 1/2" V 28 VFU

2" 2 VFU2" V 2 VFU

2" 1 WFU2" W 1 WFU

2" 1 WFU2" W 1 WFU

2" 1 WFU2" W 1 WFU

2" 1 WFU2" W 1 WFU

4" 8 VFU4" V 8 VFU

2" 24 VFU2" V 24 VFU

1 1/2"1 1/2" Undefined

2" 2 VFU2" V 2 VFU

2" W (TYP 12)2" V (TYP 12)

2" 24 VFU2" V 24 VFU

4"4" Undefined

L-2

TD-1

WC-2WCO

2" 7 VFU2" V 7 VFU

2" 1 WFU2" W 1 WFU 4" 7 WFU4" W 7 WFU

2" 6 VFU2" V 6 VFU

2" 2 VFU2" V 2 VFU4" 4 WFU4" W 4 WFU

2" 4 VFU2" V 4 VFU

L-1

2" FD-1

WCO

WC-2

WC-1

UR-1

UR-2

WC-2

WC-1(TYP 3)

2" FD-1

L-2

L-2

L-1

4" 3

2 V

FU

4" V

32

VF

U

1 1/2" 2 VFU

1 1/2" V 2 VFU

1 1/2" 2 VFU

1 1/2" V 2 VFU

2" 24 VFU2" V 24 VFU

4" 8 VFU4" V 8 VFU 2" 2 WFU2" W 2 WFU

2" 1 WFU2" W 1 WFU(TYP 4)

2" 1 WFU2" W 1 WFU

2" 8 WFU2" W 8 WFU

4" 28 WFU4" W 28 WFU

4" 36 WFU4" W 36 WFU

2" 2 VFU2" V 2 VFU

2" 2 WFU2" W 2 WFU

2" 2 VFU2" V 2 VFU

4" 8 WFU4" W 8 WFU

2" 8 VFU2" V 8 VFU

2" 4 VFU2" V 4 VFU1 1/2" 2 VFU1 1/2" V 2 VFU

4" VENT DN & UP TO4" VTR-C1 (36 VFU)






Arc

hite

ctu

re E

ngin

eering

P

lan

nin

g In

teriors

©

,

DL

R G

rou

p inc., a

Ne

bra

ska

co

rpo

ratio

n, A

LL

RIG

HT

S R

ES

ER

VE

D

KEY PLAN


A

NO

RT

H

Rev

isio

ns

B

C

D

E

F

9/2

2/2

017 2

:54:4

9 P

M

C:\R

evit\1

0-1

3125-3

0_M

P_2016_C

entr

al_

mm

art

z.r

vt

10-1

3125-3

0

8/2

9/2

017

PLA

TT

EV

IEW

JR

HIG

H &

HIG

H S

CH

OO

L R

EN

OV

AT

ION

S

PLU

MB

ING

LA

RG

E S

CA

LE

PLA

NS

& R

ISE

R D

IAG

RA

MS

P2.1

20

17

SP

RIN

GF

IELD

PLA

TT

EV

IEW

CO

MM

UN

ITY

SC

HO

OLS

SCALE: 1/4" = 1'-0"P2.1

1 LARGE SCALE ROOMS C247, C251, C255 & C256SCALE: 1/4" = 1'-0"P2.1

2 LARGE SCALE ROOM C208SCALE: 1/4" = 1'-0"P2.1

3 LARGE SCALE ROOMS C210 & C219SIM/REV ROOM 259

NO SCALEP2.1

4

WASTE AND VENT RISER DIAGRAMS ROOMS C247, C251,C255 & C256

NO SCALEP2.1

5 WASTE AND VENT RISER DIAGRAMS ROOM C208NO SCALEP2.1

6 WASTE AND VENT RISER DIAGRAMS ROOM C210 & 219

CC

-29/

20/1

7A

DD

EN

DU

M C

C-2

CC-2

E F

7

8

EWC-2 EWC-1

CS-2

CS-1

CS-1

CS-1

FUME HOOD

EEWS-1

4" FD-2

DUEL GASTURRITS (TYP 4)

SCIENCE

F223

ELEC

F224

CORRIDOR

F215

CLASSROOM

F228

CORRIDOR

F212

STORAGE

F226

CONFERENCEROOM

F225

CLASSROOM

F222

2" V DN

5" EXIST.5" SD EXIST. 1 1/2" 1 VFU1 1/2" V 1 VFU


1 1/2" 4 VFU1 1/2" AV 4 VFU

1 1/2" 2 VFU1 1/2" AV 2 VFU

2" 2

2 V

FU

2" A

V 2

2 V

FU

1 1/2" 2 VFU1 1/2" AV 2 VFU

2" 20 VFU2" AV 20 VFU

2 1/2" 28 VFU2 1/2" AV 28 VFU

EXIST. 4" FD-EX

2" AV DN & UPTO 4" AVTR-1F

2" W DN

1-1/2" TEMP. WATER DN FOREMERGENCY SHOWER ANDEYEWASH FROM ETMV

3/4" 12 MBH3/4" Gas 12 MBH

3/4" 12 MBH3/4" Gas 12 MBH

3/4" 6 MBH3/4" Gas 6 MBH

3/4" 6 MBH3/4" Gas 6 MBH

3/4" 6 MBH3/4" Gas 6 MBH

3/4"

6 M

BH

3/4"

Gas

6 M

BH

3/4" 6 MBH3/4" Gas 6 MBH

3/4" GAS DN TOTURRITS (TYP)

3/4" GAS UP(30 MBH)


3/4"

300

MB

H O

N R

OO

F3/

4" G

as 3

00 M

BH

ON

RO

OF

POUNDS TO INCHESREGULATOR ON ROOF

3/4" GAS FORFUME HOOD

1/2" CW DN

EMERGENCYGAS PANICPUCH BUTTON

EMERGENCYGAS UTILITY MASTERCONTROL PANEL

4" V UP TO 4" VTR-3F

1F

3F

1-1/2" V DN

2" AV UP TO4" AVTR-2F

2F

1-1/2" W DN

2" AV DN


3/4" 2.5 CFU3/4" CW 2.5 CFU 3/4" CW UP TORH-1 ON ROOF

4

M4.2

8

M4.2

10

M4.2


B

2

NURSE

F209

TOILET

F210

4" VTR-EX4

CS-3

L-4

WC-4

2" FD-1

2" 7 VFU2" V 7 VFU

1 1/2" 2 VFU1 1/2" V 2 VFU

4" EXIST.4" SD EXIST.4" SD DN

4" W DN (5 WFU)

2" V DN

1/2" HW DN

1-1/4" CW DN

1" 750 MBH ON ROOF1" Gas 750 MBH ON ROOF

1 1/2"1 1/2" 140-HW

1/2"1/2" 140-HWC

1-1/2" 140 HW &1/2" 104 HWC DN.

10

M4.2

(TYP)

B C D

7

8

CS-3

IMF-1 MAKE FINAL CONNECTIONS TOICE MACHINE AND OR REFRIGERATOR

MS-1

3/4" H & CW TO HB-1 & REDUCED PRESSUREBACKFLOW PREVENTER @ 60" A.F.F. FORSOAP DISPENSOR

2" FD-1

WC-2

L-2

WC-2

L-1

WC-4

WC-4

WC-3 L-4

L-4UR-2

BOYS

F204

GIRLS

F205

BOYS

F213

GIRLS

F214

JANITOR

F216

TEACHERSLOUNGE

F220WOMENS

F217

MENS

F218

CORRIDOR

F215

CORRIDOR

F219

2" FS-1

1-1/2" V DN

2" FD-1

2" FD-1

2" FD-1

WC

O

1-1/2" V DN

1-1/2" V DN

1-1/2" V DN

1 1/2" 4 VFU1 1/2" V 4 VFU

3/4" 7.75 CFU3/4" CW 7.75 CFU

2" 23 CFU2" CW 23 CFU

1/2" 1.5 CFU1/2" CW 1.5 CFU

1-1/2" W DN

4" W DN (10 WFU)2" V DN (14 VFU)

1-1/2" V DN

2" CW

2" 2

1 V

FU

2" V

21

VF

U

4" 4

6 V

FU

4" V

46

VF

U

6"6" S

D

3/4"

EX

IST

.3/

4" 1

10-H

W E

XIS

T.

1/2"

EX

IST

.1/

2" 1

10-H

WC

EX

IST

.

3/4" EXIST.3/4" 110-HW EXIST.


2" E

XIS

T.

2" C

W E

XIS

T.



B

WATER HAMMERARRESTOR (TYP)



5"5" SD


8" DS DN

WCOC4" W DN(16 WFU)

4" V DN 4" W &2" V 2" W &

1-1/2" V

2" CW

3/4" HW DN

2" 3

8 C

FU

2" C

W 3

8 C

FU

2" CW DN

4" V UP TOEXIST. 4" VTR-EX

1/2" HWC DN

2" V DN

(TYP)1/2" DRAIN FROM ROOFHYDRANT TO MOP SINK

3/4" 2.5 CFU3/4" CW 2.5 CFU

10

M4.2

C D

5

6

7

BOYS

F105

GIRLS

F106

CUSTODIAL

F102

CORRIDOR

107

2" FD-1

2" FD-1

WC-4L-4

UR-2

WC-4

WC-3

L-4

MS-1

EWC-3

3/4" H & CW TO HB-1 & REDUCEDPRESSURE BACKFLOW PREVENTERS@ 60 A.F.F. FOR SOAP DISPENSOR

EWC-2

1/2" HWC UP

8" SD UP

1/2" CW CAP

8"8" SD

1/2" CW

2" 6 VFU2" V 6 VFU

EXIST. 1-1/4" CW

EXIST. 1-1/4" HW

2" W DN

2" W & V DN

2" V DN

EXIST. 1-1/4" CW

EXIST. 1/2" HWC

EXIST. 1/2" HWC

8" EXIST.8" SD EXIST.4" 40.5 WFU EXIST.4" W 40.5 WFU EXIST.


1 1/4" EXIST.1 1/4" 110-HW EXIST.2" V UP

1-1/2" V UP

2" V DN

2" V UP (20 VFU)

4" W UP (X WFU)4" W DN (X WFU)


2" E

XIS

T.

2" C

W E

XIS

T.

2" 1

14 C

FU

2" C

W 1

14 C

FU

2" CW

2" 2 WFU2" W 2 WFU

4" 42.5 WFU4" W 42.5 WFU

2" 2 WFU2" W 2 WFU

2" CW DN & UP

4" W& 2" V

3/4" HW UP & 1/2" DN

TRAP PRIMER

TRAP PRIMER

C

WATER HAMMER ARRESTOR

(TYP)

3

M4.2(TYP)

10

M4.2

E F

7

8

SCIENCE

F111

STORAGE

F114

CORRIDOR

107

CS-3

CS-4

CS-4

CS-4

4" FD-2 ETMV-1 MOUNT TOP AT CEILING

EEWS-1

2" AV UP & 2 AW DN

1/2" HW, 1/2" CW,& 1-1/2" AW UP

1/2" HW, 1/2" CW,& 1-1/2" AW UP

1/2" HW, 1/2" CW,& 1-1/2" AW UP

1/2" HW, 1/2" CW,& 1-1/2" AW UP TOFUME HOOD

1/2" HW, 1/2" CW,& 1-1/2" AW UP.1/2" HW, 1/2" CW, 1-1/2 V & 2" AW DN

1/2" CW UP,1-1/2" W UP & DN

4" 9 WFU4" AW 9 WFU

WCO

4" AW DN(18 WFU)

CO 2" 2 WFU2" AW 2 WFU 2" 5 WFU2" AW 5 WFU

4" 1

1 W

FU

4" A

W 1

1 W

FU

1 1/2" 2 VFU1 1/2" AV 2 VFU

2" F

D-2

4" AW UPTO FD

2" AW UP

2" AV DN & UPCLASSROOM

F117

CLASSROOM

F110

4" 13 WFU4" AW 13 WFU

2" 104 CFU2" CW 104 CFU2" 71.5 HFU2" 110-HW 71.5 HFU

3/4" 3 CFU3/4" CW 3 CFU

3/4" 3 HFU3/4" 110-HW 3 HFU

3/4" 3 HFU3/4" 110-HW 3 HFU

3/4" 3 CFU3/4" CW 3 CFU

2" 9

3 C

FU

2" C

W 9

3 C

FU

2" 6

1 H

FU

2" 1

10-H

W 6

1 H

FU

3/4"

3 C

FU

3/4"

CW

3 C

FU

3/4"

3 H

FU

3/4"

110

-HW

3 H

FU

1 1/2" 58 HFU1 1/2" 110-HW 58 HFU

2" 90 CFU2" CW 90 CFU

3/4" 3.5 CFU3/4" CW 3.5 CFU

CO

1-1/2" TEMP. WATERUP & DN FOR EEWS-1

2" W &1-1/2" V DN

1" FM DN TO 2"STANDPIPE 42" A.F.FWITH AIR GAP FITTING

1" FM DN TOSUMP PUMPSP-1

FCO-EX

1-1/2" V UP

1 1/2" 2 VFU1 1/2" AV 2 VFU

1 1/

2" 2

VF

U1

1/2"

AV

2 V

FU

1 1/

2" 2

VF

U1

1/2"

AV

2 V

FU

1 1/2" 2 WFU1 1/2" AW 2 WFU

1/2" HW, 1/2" CW,& 2" AW DN (TYP 4)

2" AV UP & DN

2" AV UP

2" AV DN

1-1/2" V UP

NT-1

10

M4.2

E F G

1

MS-13/4" H & CW DN TO HB-1 & REDUCEDPRESSURE BACKFLOW PREVENTER@ 60" A.F.F. FOR SOAP DISPENSOR

UR-2

WMF-1

WC-4WC-4

WC-3 WC-3

WC-3

L -4L-4

GIRLS

F243

BOYS

F242

ELECTRICAL

F238

COORIDOR

F241ALCOVE

F236

JANITOR

F237

2" 8 VFU2" V 8 VFU

2" V DN

1"1 1/2" EXIST.1 1/2" 140-HW EXIST.


2" FD-EX 2" FD-EX

WCO

WCO

C

C

WATER HAMMERARRESTOR (TYP)

4" W DN & 4" V UP & DN

2" CW (TYP)


1 1/2" 1 VFU1 1/2" V 1 VFU

1" EXIST.1" 110-HW EXIST.




3/4" EXIST.3/4" CW EXIST.

2" EXIST. CW DN 2" CW

3/4" CAPS

EXIST. 4" VTR-EX


2" EXIST.2" 110-HW EXIST.


1 1/2" EXIST.1 1/2" 140-HW EXIST.



1/2"1/2" 140-HWC

1 1/2"1 1/2" 140-HW

1/2" CAP

1-1/2" CAP

10

M4.2(TYP)

1/2" DRAIN FROM ROOF HYDRANT TODRAIN INTO MOP SINK WITH 2" AIR GAP






Arc

hite

ctu

re E

ngin

eering

P

lan

nin

g In

teriors

©

,

DL

R G

rou

p inc., a

Ne

bra

ska

co

rpo

ratio

n, A

LL

RIG

HT

S R

ES

ER

VE

D

KEY PLAN


A

NO

RT

H

Rev

isio

ns

B

C

D

E

F

9/2

2/2

017 2

:55:0

8 P

M

C:\R

evit\1

0-1

3125-3

0_M

P_2016_C

entr

al_

mm

art

z.r

vt

10-1

3125-3

0

8/2

9/2

017

PLA

TT

EV

IEW

JR

HIG

H &

HIG

H S

CH

OO

L R

EN

OV

AT

ION

S

PLU

MB

ING

LA

RG

E S

CA

LE

PLA

NS

P2.2

20

17

SP

RIN

GF

IELD

PLA

TT

EV

IEW

CO

MM

UN

ITY

SC

HO

OLS

SCALE: 1/4" = 1'-0"P2.2

3 LARGE SCALE ROOM F212 & F223

SCALE: 1/4" = 1'-0"P2.2

4 LARGE SCALE ROOMS F209 & F210SCALE: 1/4" = 1'-0"P2.2

5 LARGE SCALE ROOMS F213 THRU F218 & F220

SCALE: 1/4" = 1'-0"P2.2

2 LARGE SCALE ROOMS F102, F105 & F106SCALE: 1/4" = 1'-0"P2.2

1 LARGE SCALE ROOM F111 & F114

SCALE: 1/4" = 1'-0"P2.2

6 LARGE SCALE ROOMS F237, F242 & F243

CC

-29/

20/1

7A

DD

EN

DU

M C

C-2

CC-2

CC-2

CC-2

CC-2

CC-2

MS-1

EWC-3

EWC-2WC-4

WC-4

WC-3

L-4

L-4

UR-2

2" FS-1

2" FD-1

2" FD-1

2" FD-1

2" FD-1MS-1

2" FD-1

2" FD-1

4" 46 VFU

4" V 46 VFU

1 1/2" 4 VFU

1 1/2" V 4 VFU

1 1/

2" 5

VF

U1

1/2"

V 5

VF

U

3" 6 WFU

3" W 6 WFU

2" 6 VFU

2" V 6 VFU

2" 6

VF

U2"

V 6

VF

U

2" 14 VFU2" V 14 VFU1 1/2" 2 VFU1 1/2" V 2 VFU

1 1/2" 2 WFU1 1/2" W 2 WFU

2" 4 WFU2" W 4 WFU

4" 15.5 WFU EXIST.

4" W 15.5 WFU EXIST.

4" 40.5 WFU EXIST.4" W 40.5 WFU EXIST.

4" 21 WFU4" W 21 WFU

3" 5 WFU3" W 5 WFU

2" 2 WFU2" W 2 WFU

1 1/2" 2 VFU1 1/2" V 2 VFU

1 1/2" 2 VFU1 1/2" V 2 VFU

2" 2 WFU2" W 2 WFU

4" 4 WFU4" W 4 WFU

CS-3

WCO

WC-2

L-2WC-2

L-2

WC-4

WC-4

WC-3

UR-2

L-4

2" 21 VFU

2" V 21 VFU

4" 42.5 WFU4" W 42.5 WFU

2" 20 VFU2" V 20 VFU

4" 8 WFU4" V 8 WFU

4" 44.5 WFU4" W 44.5 WFU

2" 2 WFU2" W 2 WFU1 1/2" 2 VFU1 1/2" V 2 VFU

2" 2 WFU2" W 2 WFU

1 1/2" 2 WFU1 1/2" V 2 WFU

2" 8 WFU2" V 8 WFU

2" 18 WFU2" V 18 WFU

4" 8 WFU4" W 8 WFU

2" 2 WFU2" W 2 WFU

4" 16 WFU4" W 16 WFU

4" EXIST. 63 VFU4" V EXIST. 63 VFU

4" VTR-EX

4" EXIST.

4" W EXIST.

4" EXIST.

4" W EXIST.2" E

XIST.

2" W EXIST.

4" EXIST.4" W EXIST.


2" 2 WFU2" W 2 WFU

2" 8 VFU2" V 8 VFU

1 1/2" 2 VFU1 1/2" V 2 VFU


4" 8 WFU4" W 8 WFU

2" 20 VFU2" V 20 VFU

2" 8 VFU2" V 8 VFU

2" 2 VFU2" V 2 VFU

2" 2 WFU2" W 2 WFU2" EXIST.2" W EXIST.

2" 4 WFU2" V 4 WFU

L-4

CO

CS-1

EEWS-1

CS-4

EEWS-1CS-4

CS-4

CS-3

CS-1

FUME HOOD

EWC-2

EWC-1

CS-2

CO

CS-1

4" FD-2

4" FD-1

2" FD-1

4" AVTR-1F

1 1/2" 2 VFU

1 1/2" AV 2 VFU

2" 20 VFU

2" AV 20 VFU

1 1/2" 4 VFU

1 1/2" AV 4 VFU

1 1/2" 2 VFU

1 1/2" AV 2 VFU

1 1/2" 1 VFU

1 1/2" V 1 VFU

1 1/

2" 2

WF

U1

1/2"

AV

2 W

FU

2" 2 WFU

2" AW 2 WFU

2" 5 WFU

2" AW 5 WFU

2" 1

8 V

FU

2" A

V 1

8 V

FU

2" 9

VF

U2"

AV

9 V

FU

2" 2 WFU2" AW 2 WFU

2" 2 WFU

2" AW 2 WFU

4" 14 WFU

4" AW 14 W

FU

2" 2 WFU

2" AW 2 WFU


2" EXIST.

2" W EXIST.

CO-EX

2" 6 VFU2" AV 6 VFU

2" 3 WFU2" AW 3 WFU

4" 12 WFU4" AW 12 WFU

4" 6 WFU4" W 6 WFU

4" 11 WFU

4" AW 11 W

FU

4" 6 WFU4" AW 6 WFU

2" 6 VFU2" AV 6 VFU

2" 3 WFU2" AW 3 WFU4" 9 WFU4" AW 9 WFU

1 1/2" 2 WFU1 1/2" AW 2 WFU

1 1/

2" 2

VF

U1

1/2"

AV

2 V

FU


4" 36 WFU4" AW 36 WFU

2" 2 VFU2" AV 2 VFU2" 4 WFU2" AW 4 WFU

1 1/2" 2 VFU1 1/2" AV 2 VFU

1 1/2" 2 VFU1 1/2" AV 2 VFU

1 1/2" 2 WFU1 1/2" AW 2 WFU

2 1/2" 28 VFU2 1/2" AV 28 VFU

2" 24 VFU2" AV 24 VFU 1 1/2" 2 WFU1 1/2" AV 2 WFU

1 1/

2" 1

WF

U1

1/2"

W 1

WF

U

4" AVTR-2F

4" VTR-3F

FCO-EX

2" STANDPIPE


1 1/

2" 3

VF

U1

1/2"

V 3

VF

U

2" 3

6 V

FU

2" A

V 3

6 V

FU

2" 1 WFU2" W 1 WFU

WCO

4" 1

8 W

FU

4" A

W 1

8 W

FU

1 1/2" 2 VFU1 1/2" AV 2 VFU

1 1/2" 2 VFU1 1/2" AV 2 VFU2" 2 WFU2" AW 2 WFU

1 1/2" 2 VFU1 1/2" AV 2 VFU

1 1/2" 2 VFU1 1/2" AV 2 VFU

2" 10 VFU2" AV 10 VFU

NT-1

2" 4 VFU2" AV 4 VFU

2" 22 VFU

2" AV 22 VFU

2" FD-1

WC-4

L-4

CS-3

2" 7 VFU2" V 7 VFU

4" 5 WFU4" W 5 WFU

1 1/2" 2 VFU1 1/2" V 2 VFU

2" 5 VFU2" V 5 VFU

1 1/2" 2 WFU1 1/2" W 2 WFU





WCO-EX

2" EXIST.2" V EXIST.


4" VTR-EX4

2" 2 VFU2" V 2 VFU

WMF-1MS-1

EXIST. 4" VTR-EX

2" FD-EX

2" FD-EX

L-4

L-4

WCOUR-2

WC-3

WC-4

WCO

WC-3

WC-3

WC-4

2" 8 VFU

2" V 8 VFU

2" 1 WFU

2" W 1 WFU

4" 8 WFU4" V 8 WFU

4" 8 WFU4" W 8 WFU

2" 2 WFU2" W 2 WFU

1 1/2" 2 VFU1 1/2" V 2 VFU

2" 4 VFU2" V 4 VFU

2" 8 VFU2" V 8 VFU



4" 8WFU4" W 8WFU2" 8 VFU2" V 8 VFU

2" 5 VFU2" V 5 VFU

2" 3 VFU2" V 3 VFU

3" 5 WFU3" W 5 WFU

3" 3 WFU3" W 3 WFU


Arc

hite

ctu

re E

ngin

eering

P

lan

nin

g In

teriors

©

,

DL

R G

rou

p inc., a

Ne

bra

ska

co

rpo

ratio

n, A

LL

RIG

HT

S R

ES

ER

VE

D

Rev

isio

ns

9/2

2/2

017 2

:55:1

9 P

M

C:\R

evit\1

0-1

3125-3

0_M

P_2016_C

entr

al_

mm

art

z.r

vt

10-1

3125-3

0

8/2

9/2

017

PLA

TT

EV

IEW

JR

HIG

H &

HIG

H S

CH

OO

L R

EN

OV

AT

ION

S

WA

ST

E A

ND

VE

NT

RIS

ER

DIA

GR

AM

SP

3.1

20

17

SP

RIN

GF

IELD

PLA

TT

EV

IEW

CO

MM

UN

ITY

SC

HO

OLS

NO SCALEP3.1

1

WASTE AND VENT RISER DIAGRAMS ROOMS F101,F102,F105,F106, F213, F214, F216, F217, F218 & F220

NO SCALEP3.1

2

WASTE AND VENT RISER DIAGRAMS ROOMS F111, F212 &F223

NO SCALEP3.1

3 WASTE AND VENT RISER DIAGRAMS ROOMS F209 & 210NO SCALEP3.1

4 WASTE AND VENT RISER DIAGRAMS ROOMS F237, 242 & 243

CC

-29/

20/1

7A

DD

EN

DU

M C

C-2

CC-2

CC-2

CC-2

CC-2

Arc

hite

ctu

re E

ngin

eering

P

lan

nin

g In

teriors

©

,

DL

R G

rou

p inc., a

Ne

bra

ska

co

rpo

ratio

n, A

LL

RIG

HT

S R

ES

ER

VE

D

Revi

sio

ns

9/2

1/2

017 3

:57:0

6 P

M

C:\R

evit\1

0-1

3125-3

0_E

L_2016_C

entr

al_

mw

urs

t.rv

t

10-1

3125-3

0

8/2

9/2

017

PLA

TT

EV

IEW

JR

HIG

H &

HIG

H S

CH

OO

L R

EN

OV

AT

ION

S

ELE

CT

RIC

AL L

IGH

TIN

G S

CH

ED

ULE

SE

7.1

20

17

SP

RIN

GF

IELD

PLA

TT

EV

IEW

CO

MM

UN

ITY

SC

HO

OLS

LIGHT FIXTURE SCHEDULE

TYPE MANUFACTURER MODEL LAMP VOLTAGE APPARENT LOAD DESCRIPTION

D1 GOTHAM

PORTFOLIO

PRESCOLITE

EVO LED 4000K

1000 LUMENS

277 V 12 VA 6" DOWNLIGHT, CLEAR MATTE DIFFUSE OPEN REFLECTOR, MEDIUM WIDE DISTRIBUTION, 0-10V DIMMING, 16-GAUGE

GALVANIZED STEEL CONSTRUCTION, SELF-FLANGED REFLECTOR, LIGHT ENGINE AND DRIVER ACCESSIBLE

THROUGH APERTURE.

D2V GOTHAM

PORTFOLIO

PRESCOLITE

EVO LED 4000K

1000 LUMENS

120 V 22 VA 6" DOWNLIGHT NON-CONDUCTIVE FRONT, REGRESSED LENS, WHITE FINISH, IP65 RATED, 16-GAUGE GALVANIZED

STEEL CONSTRUCTION, SELF-FLANGED REFLECTOR, LIGHT ENGINE AND DRIVER ACCESSIBLE THROUGH APERTURE.

EM LITHONIA ELM2 LED 120 V 3 VA LOW PROFILE EMERGENCY LIGHTING UNIT, SEALED MAINTENANCE-FREE NICKEL-CADMIUM BATTERY, SELF

DIAGNOSTICS, CEILING OR WALL MOUNT. WHITE FINISH, PROVIDE WITH WIREGUARD WHERE MARKED 'WG'.

EP1 SELUX SACL LED 4000K

5500 LUMENS

277 V 70 VA EXTERIOR POST-TOP LIGHT FIXTURE, TYPE III DISTRIBUTION, 12 FOOT ROUND STRAIGHT POLE, SILVER FINISH.

EW1 LITHONIA

METALUX

WSQ LED 4000K

2000 LUMENS

277 V 24 VA WALL MOUNT EXTERIOR LIGHT FIXTURE, TYPE II DISTRIBUTION, ALUMINUM CONSTRUCTION, DARK BRONZE FINISH.

EW2 LITHONIA

METALUX

WSQ LED 4000K

2000 LUMENS

277 V 24 VA WALL MOUNT EXTERIOR LIGHT FIXTURE, TYPE IV DISTRIBUTION, ALUMINUM CONSTRUCTION, DARK BRONZE FINISH.

P1 LITHONIA

METALUX

H.E. WILLIAMS

ZL2N LED 4000K

2000 LUMENS

277 V 31 VA CRS HOUSING, DIE FORMED CHANNEL CONNECTOR FOR STRAIGHT ROWS, BAKED ENAMEL WHITE FINISH, AIR CRAFT

CABLE MOUNTED, DIFFUSE LENS.

P1V LITHONIA

METALUX

H.E. WILLIAMS

ZL2N LED 4000K

2000 LUMENS

120 V 31 VA SAME AS P1, PROVIDE AT 120V.

P2 LITHONIA

METALUX

H.E. WILLIAMS

ZL2N LED 4000K

3000 LUMENS

277 V 42 VA CRS HOUSING, DIE FORMED CHANNEL CONNECTOR FOR STRAIGHT ROWS, BAKED ENAMEL WHITE FINISH, AIR CRAFT

CABLE MOUNTED, DIFFUSE LENS.

P2V LITHONIA

METALUX

H.E. WILLIAMS

ZL2N LED 4000K

3000 LUMENS

120 V 42 VA SAME AS P2, PROVIDE AT 120V.

P3-2' BARTCO BSS610 LED 4000K

8W/FT

277 V 16 VA MULTI-AXIS DIRECT LED LUMINAIRE SYSTEM, LENGTHS CONNECTED IN CONFIGURATIONS AS SHOWN ON DRAWINGS,

PROVIDE JOINING MODULES AS NEEDED, ALUMINUM HOUSING, AIR CRAFT CABLE SUSPENSION, WHITE FINISH, 0-10V

DIMMING.


8W/FT



DIMMING.


8W/FT



DIMMING.


8W/FT



DIMMING.


8W/FT



DIMMING.

P4 TECH LIGHTING 700 BSTP BRISTOL LED 3000K

700 LUMENS

120 V 9 VA BULB SHAPED GLASS PENDANT, CLEAR SMALL SHADE, BLACK FINISH, 0-10V DIMMING.

R1V LITHONIA

METALUX

GTL LED 4000K

3300 LUMENS

120 V 35 VA RECESSED GRID 1X4 TROFFER WITH PRISMATIC #12 PATTERN ACRYLIC 0.125" THICK LENS, STEEL HOUSING, WHITE

FINISH, 0-10V DIMMING TO 1%.

R2 LITHONIA

FS SERIES

2FSL2 LED 4000K

4000 LUMENS



R3 LITHONIA

METALUX

2GTL LED 4000K

3300 LUMENS



R3V LITHONIA

METALUX

2GTL LED 4000K

3300 LUMENS

120 V 36 VA SAME AS R3, PROVIDE AT 120V.

R4 LITHONIA

METALUX

2GTL LED 4000K

4000 LUMENS



R4V LITHONIA

METALUX

2GTL LED 4000K

4000 LUMENS

120 V 39 VA SAME AS R4, PROVIDE AT 120V.

R5 LITHONIA

METALUX

2GTL LED 4000K

4800 LUMENS



R6 FAIL-SAFE CLM LED 4000K

4000 LUMENS

277 V 53 VA RECESSED GRID, CLEAN ROOM, 2X4 TROFFER WITH PRISMATIC #12 PATTERN ACRYLIC 0.125" THICK LENS, INSET

STEEL GASKETED DOOR, SEALED STEEL HOUSING, WHITE FINISH.

T1 BRUCK TRACK CHROMA MAG II

ECO

LED 4000K

1000 LUMENS

120 V 600 VA AIMABLE LED 40 DEGREE SPOT FIXTURE, ALUMINUM HOUSING, CRI > 80, INTEGRAL DRIVER, ECO SINGLE CIRCUIT

TRACK, LENGTH AS INDICATED ON DRAWINGS, TRACK HEAD QUANTITIES AS SHOWN, PROVIDE ALL ACCESSORIES

FOR A COMPLETE INSTALLATION, WHITE FINISH.

X1 LITHONIA

DUAL-LITE

SURE-LITES

LQC LED 277 V 3 VA UNIVERSAL MOUNT EXIT SIGN, NICKEL-CADMIUM BATTERY BACK-UP, DIE CAST ALUMINUM CONSTRUCTION, SINGLE

FACE, RED LETTERS, ALL WHITE FINISH.

X1V LITHONIA

DUAL-LITE

SURE-LITES

LQC LED 120 V 3 VA SAME AS X1, PROVIDE AT 120V.

X2 LITHONIA

DUAL-LITE

SURE-LITES

LQC LED 277 V 3 VA UNIVERSAL MOUNT EXIT SIGN, NICKEL-CADMIUM BATTERY BACK-UP, DIE CAST ALUMINUM CONSTRUCTION, DOUBLE

FACE, RED LETTERS, ALL WHITE FINISH.

4. ZONE CONTROL VIA INDOOR PHOTOCELL, MAINTAIN 30 FOOTCANDLES.

3. SWITCH ON/OFF, SWEEP OFF AT PRESET TIME.

2. DAWN TO DUSK VIA OUTDOOR PHOTOCELL CONTROL

1. 0-10V DIMMING RELAY

LIGHTING CONTROL PANEL SCHEDULE NOTES:

Z15 L1-32 LOBBY F212 PENDANTS 120 1

Z14 LS-11 SITE LIGHTING EAST 277 2

Z13 LS-9 SITE LIGHTING WEST 277 2

Z12 LS-7 FAÇADE LIGHTING NORTH 277 2

Z11 LS-5 FAÇADE LIGHTING SOUTH 277 2

Z10 H1-3 MEDIA CENTER NE. 277 1,3,4

Z9 H1-3 MEDIA CENTER SE. 277 1,3,4

Z8 H1-3 MEDIA CENTER W. 277 1,3

Z7 H1-9 RAMP/STAIRS S. 277 1,3,4

Z6 H1-9 RAMP/STAIRS N. 277 1,3,4

Z5 H1-9 CORRIDOR MAIN LEVEL F215, F227 277 1,3

Z4 H1-9 LOBBY F212 277 1,3,4

Z3 H1-5 RECEPTION F206, F211 277 1,3

Z2 H1-9 LEARNING COMMONS F232 277 1,3

Z1 H1-3 CORRIDOR LOWER LEVEL F101, F107, F116 277 1,3

ZONE PANEL CKT LOAD DESCRIPTION VOLTAGE NOTES

LIGHTING CONTROL SCHEDULE

3. COORDINATE 8 LIGHTING PRESET BUTTONS WITH OWNER.

2. PROVIDE TOUCH SCREEN CONTROL, NLIGHT NPOD GFX OR APPROVED EQUAL.

1. FOR ZONES CONTROLLED BY PHOTOCELL, SWITCH CANNOT INCREASE LIGHT LEVEL BEYOND PHOTOCELL PRESET, SWITCH CAN DECREASE LIGHT LEVEL BELOW PRESET.

LIGHTING CONTROL SWITCH SCHEDULE NOTES:

C. SCHEDULE TRAINING THROUGH ARCHITECT/ENGINEER. DLR GROUP ENGINEER TO BE PRESENT AT OWNER TRAINING.

B. SCHEDULE ONSITE VISIT WITHIN 3 MONTHS OF SUBSTANTIAL COMPLETION TO ASSIST OWNER IN ADJUSTING SENSORS AND MODIFYING PROGRAMING.

A. SEE SPECIFICATION FOR ADDITIONAL REQUIREMENTS.

GENERAL NOTES:

15 Z13,Z14 EXTERIOR OVERRIDE ON/OFF

14 Z11,Z12 FAÇADE OVERRIDE ON/OFF

13 Z1-Z10 ALL ON/OFF/DIM

12 Z2 COMMONS ON/OFF/DIM

11 Z6,Z7 RAMP ON/OFF/DIM

10 Z4 LOBBY ON/OFF/DIM

9 Z8,Z9,Z10 MEDIA CENTER ON/OFF/DIM

LV3 RECEPTION F206 8 Z5 UPPER LEVEL ON/OFF/DIM 1,2,3

7 Z1 LOWER LEVEL ON/OFF/DIM

6 Z15 PENDANTS ON/OFF/DIM

5 Z3 RECEPTION ON/OFF/DIM

4 Z1-Z10, Z15 ALL OFF OFF

3 Z1-Z10, Z15 ALL 50% ON/OFF/DIM



4 OFF Z1-Z10 OFF ALL ZONES OFF

3 ON Z1-Z10 ON 50% ALL ZONES DIMMED TO 50% OUTPUT

LV2 JANITOR F237 2 ON Z1-Z10 ON 70% ALL ZONES DIMMED TO 70% OUTPUT 1

1 ON Z1-Z10 ON 100% ALL ZONES ON

4 LOWER Z8,Z9,Z10 ↓ DECREASE LIGHT LEVEL

3 RAISE Z8,Z9,Z10 ↑ INCREASE LIGHT LEVEL

LV1 MEDIA CENTER F121 2 OFF Z8,Z9,Z10 OFF ALL ZONES OFF 1

1 ON Z8,Z9,Z10 ON ALL ZONES ON

SWITCH ROOM BUTTONFUNCTION

TYPECONTROLS ZONES ENGRAVING DIRECTION NOTES

LIGHTING CONTROL SWITCH SCHEDULE

CC

-29

/21/1

7A

DD

EN

DU

M C

C-2

CC-2