aca42 instructionmanual100801

Mode Door

1 2 3

4 5 6

7 8 9

0 #

ROSSLAREINSTRUCTION MANUAL

AC-A42STAND-ALONE

ACCESS CONTROL UNIT

08/019J-I

DR

-021-A

/0706-0

820021-0

1

ROSSLAR E

www.rosslare.com.hk

ROSSLAR E

06/01

Replacing a lost Programming Code 35Replacing a lost Normal / Secure Code 35

Glossary 36APPENDIX

TECHNICAL SUPPORT 39

Page 3AC-A42 06/01

Contents

Technical Specifications 5Key Features 6

Mounting the AC-A42 Controller 7Wiring Diagrams 9

Normal, Secure, & Master Users 12Modes Of Operation 13Changing the Modes of Operation 14Auxiliary Output and Input 15Request To Exit (REX) Button 16Case and Back Tamper 16BL-D40 External Sounder 17

Entering Programming Mode 19Exiting Programming Mode 19

1 Changing the Open Code 202 Changing the Auxiliary Code 203 Changing the Programming Code 214 Changing the Normal / Secure Code 225 Changing the Normal / Bypass Code 22

Door Chime Settings 226 Defining the Auxiliary Input and Output 24

Auxiliary Mode Quick Reference Guide 25Setting Fail Safe / Secure Operation 26Setting Tamper Siren Time 26Setting the Lock Strike Release Time 26

7 Enrolling Primary and Secondary Codes 278 Deleting Primary and Secondary Codes 309 Lock Strike Relay and Auxiliary Relay 32

Code Assignment0 Return to Factory Default Settings 34

INTRODUCTION

INSTALLATION

FEATURES AND CONCEPTS

PROGRAMMING THE AC-A42

4

7

18

AC-A42

08/01

Technical Specification

Electrical Characteristics

Environmental Characteristics

Mechanical Characteristics

Operating Voltage Range:

Maximum Input Current:

Relay Outputs:

Inputs:

LEDs

Built-In Proximity Reader

Operating Temperature:

Operating Humidity:

Dimensions:

Weight:

*

12 to 16V DC From a Regulated Power Supply

Standby: 40mA Not including attached devicesMax: 100mA Not including attached devices

Lock Strike Relay Electronic, 3.5Awith built in suppressor protection

Auxiliary Relay Form C, 1A

REX N.O., Dry ContactAuxiliary Input (In / Monitor) N.C., Dry Contact in Monitor Mode

N.O., Dry Contact in Input Mode

Two Tri-colored LEDs

Read Range* 3.5" (90mm)Modulation ASK at 125kHzCompatible Cards All 26-Bit EM Cards

-25°F to 145°F (-31°C to 63°C)

0 to 95% (Non-Condensing)

4.80" (122mm) L x 2.95" (75mm) W x 0.94" (24mm) D

0.3 lbs (140g)

Measured using Rosslare Proximity Card (AT-11/12) orequivalent. Range also depends on electrical environment andproximity to metal.

Page 5AC-A42

Introduction

Equipment provided

The following is provided as part of every AC-A42 package:

The AC-A42 is a proximity card and keypad access control unit.

The unit accepts up to 500 users and provides entry via the use ofproximity cards and/or PIN codes.

- AC-A42 Access Control Unit.- Installation Kit- Installation and Operating Instructions

Fail Safe (Power to Lock) or Fail Secure (Power to Open)

12 to 16V DC (From a Regulated Power Supply)

Normally Open Type - Switch is closed when pressed.

Provides Siren, Bell, and Chime functions to AC-A42

Other Rosslare accessories can be found at Rosslare'sWeb Site:

http://www.rosslare.com.hk

Additional Equipment Required

1) Electric Lock Strike Mechanism

2) Power Supply with Backup Battery

3) Request To Exit (REX) Button

4) BL-D40 External Sounder (Optional)

Page 4 06/01AC-A42

Mode Door

1 2 3

4 5 6

7 8 9

0 #

Door LED

3 x 4 Matrix Keypad

Mode LED

Bezel Screw

Bell Button

Installation

Mounting the AC-A42 Controller

1)

2)

3)

Before starting, select the location to mount the AC-A42controller. This location should be at shoulder height and on thesame side as the door handle.

The AC-A42 is designed to be easily mounted to a US Gang Box.Remove the Bezel Screw. (Use the diagram below to help youlocate the Bezel Screw)

Screw the controller onto a US Gang Box through the twoMounting Holes provided. (See diagram on the next page to helpyou locate the US Gang Box mounting holes )

Page 7 06/01AC-A42Page 6 06/01

Key Features

Here are some of the AC-A42's key features:

Built in Proximity Card Reader (125 KHz ASK Modulation)Built in Keypad for PIN code entryAuxiliary Input & Auxiliary OutputEight Auxiliary Modes including:

Door AjarForced DoorShuntDoor MonitorNormal / Secure

Internal BuzzerComes with security screw and security screw toolTwo Status / Programming Interface LED'sThree User Levels

Normal UserSecure UserMaster User

Three Modes of OperationNormal ModeBypass ModeSecure Mode

"Code Search" feature that helps make maintaining user codeseasier.Lock Strike Electronic Relay with built-in suppressorproduction.Input for Request to Exit (REX) button.Comes with mounting template for easier installation.Built in Case and Back TamperBell, Chime, Siren, and Strobe features available with BL-D40.Bell, Chime, Siren, Battery Backup, Tamper Output (OpenCollector 20mA) features available with PS-X41 (Output Power1.2A) and PS-X42 (Output Power 1.8A).Programmable Siren TimeProgrammable Lock Strike Release Time

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

AC-A42

EL

EC

TR

ICL

OC

KS

TR

IKE

FA

ILS

AF

Eo

rFA

ILS

EC

UR

E

REX

CO

MM

ON

PO

WE

RS

UP

PLY

12

V-

16

VD

C

Mo

de

Do

or

12

3

45

6

78

9

0#

(+)

(-)

Lo

ck

RE

X/

BL

(+)

(-)

(-)

Lock

(-)REX/BL

06/01Page 9AC-A42

Wiring Diagrams

Wir

ing

the

Lo

ck

Str

ike

Rela

yan

dR

EX

Page 8 08/01

4)

5)

Pass the wires through the exit/entry holes and attach them tothe controllers terminal blocks as shown in the wiring diagrams.(Wiring diagrams for common installations can be found onpages 10 to 12).

Replace the controller’s bezel and replace the factory defaultscrew with the security screw that is provided in the InstallationKit. A security screw tool is also provided in the Installation Kit.

A few of the typical wiring diagrams are shown on the next threepages; for other wiring diagram examples refer to the supportsection of the Rosslare Web Site.

http://www.rosslare.com.hk/support

Wiring the AC-A42 Controller

AC-A42

Mode Door

1 2 3

4 5 6

7 8 9

0 #

Mounting Hole

Mounting Hole

(+)(-)

LockREX / BL

COMN.C.N.O.

AUX INPUT

Terminal Blocks

AC-A42

AC

-A4

2

Wirin

gth

eA

uxilia

ryIn

pu

tan

dO

utp

ut

Page 10 06/01AC-A42

CO

MM

ON

PO

WE

RS

UP

PLY

12

V-

16

VD

C

Mo

de

Do

or

12

3

45

6

78

9

0#

(+)

(-)

(+)

(-)

CO

MN

.C.

N.O

.

Au

xilia

ryR

ela

y

AU

XIL

IAR

YIN

PU

T(M

ON

ITO

R)

AUX. IN

CO

M

N.C

.

N.O

.

AU

XIN

PU

T

Page 11 05/01AC-Q42

Wir

ing

the

BL

-D40

Exte

rnalS

ou

nd

er

CO

MM

ON

PO

WE

RS

UP

PLY

12V

-1

6V

DC

Mo

de

Do

or

12

3

45

6

78

9

0#

(+)

(-)

RE

X/

BL

(+)

(-)

REX/BL

(+)

(-)

BL

-D40

AC

-A42

AC

-A42

06/0106/01

Normal, Secure, & Master Users

The AC-A42 accepts up to 500 users and provides entry via the useof proximity cards and / or PIN codes. Each user is provided withtwo code memory slots, Memory Slot 1 (Primary Code) andMemory Slot 2 (Secondary Code). The two memory slots can beprogrammed as Proximity Cards, PIN codes, or a combination ofboth Proximity Cards and PIN codes.

The way in which the two memory slots are programmeddetermines a users access level and also determines the way inwhich the AC-A42 grants access in its three Modes of Operation.

A Normal User only has a Primary Code and is onlygranted access when the AC-A42 is in Normal orBypass Mode.

A Secure User must have a Primary and SecondaryCode programmed, the two codes must not be thesame. The Secure User can gain access when theAC-A42 is in any of its three Modes of Operation. InNormal Mode the Secure User must use theirPrimary Code to gain entry. In Secure Mode theSecure User must present both their Primary andSecondary Codes in order to gain entry.

A Master User must have both Primary andSecondary Codes programmed with the sameProximity Card or PIN code. The Master User cangain access during any Mode of Operation bypresenting their Proximity Card or PIN code to thecontroller. (The Master User is convenient but is lesssecure than a Secure User).

There are three user levels:

Normal User

Secure User

Master User

Modes of Operation

�

The AC-A42 has 3 Modes of Operation:

1) Normal Mode

2) Bypass Mode.

3) Secure Mode.

.Mode LED is green

Normal Mode is the default mode. In Normal Mode the door islocked until a Primary Code is presented to the controller. Specialcodes such as “Open Code” and “Auxiliary Code” are active inNormal mode. (See Page 20 for more information on the Open &Auxiliary Codes).

Mode LED is orange

In Bypass Mode, access to the premises is dependent onwhether the controller's Lock Strike Relay is programmed for FailSafe Operation or Fail Secure Operation.

When the Lock Strike Relay is programmed forFail Secure Operation, the door is locked until the DoorBell Button is pressed.

When the Lock Strike Relay is programmed forFail Safe Operation, the door is constantly unlocked.

Mode LED is red

Only Secure and Master Users can access the premises duringthe Secured Mode.

A Secure User must enter their Primary andSecondary Codes to gain entry. After entering their PrimaryCode the Door LED will flash green for 10 seconds, duringwhich the Secondary Code must be entered.

A Master User only needs to present their ProximityCard or PIN code once to gain entry.

�

�

Page 13AC-A42 AC-A42

Mode Door

GREEN

Mode Door

ORANGE

Mode Door

RED

06/0106/01

Changing the Modes of Operation

Changing from Normal Mode to Secure Mode

Changing from Secure Mode to Normal Mode

:

:

The default factory setting for the Normal / Secure Code is 3838

Enter the 4-digit Normal / SecureCode

Mode LED will flash red

Press the key to confirmthe Mode change.

Mode LED is red

The AC-A42 Auxiliary Input can also be used to switch the Mode ofOperation from Normal to Secure and vice versa. Refer to "Definingthe Auxiliary Input and Output" on Page 24.

The default factory setting for the Normal / Secure Code 3838

Enter the 4-digit Normal / SecureCode.

Mode LED will flash green.


Mode LED will turn green.

The Auxiliary Input of the AC-A42 can also be used to switch themode of operation from Secure to Normal Mode and vice versa.Refer to "Defining the Auxiliary Input and Output" on Page 24.

1)

2) "#"

1)

2) "#"

�

�

�

�

Changing from Normal Mode to Bypass Mode

Changing from Bypass Mode to Normal Mode

:

See Page 22 to create / modify the Normal / Bypass Code

Enter the 4 digit Normal / BypassCode.

Mode LED will flash orange


Mode LED will turn orange

See page 22 to create/modify the Normal / Bypass Code

Enter the 4 digit Normal / BypassCode.

Mode LED will flash green


Mode LED will turn green

The AC-A42 auxiliary input and output can be configured in 8different combinations, for optimum usability in differentapplications.

For more information, refer to "Defining the Auxiliary Input andOutput" on Page 24.

1)

2) "#"

1)

2) "#"

�

�

�

�

:

Auxiliary Input and Output


Mode Door

GREEN

Mode Door

Mode Door

GREEN

Mode Door

RED

Mode Door

RED

Mode Door

Mode Door

Mode Door

RED

GREEN

GREEN

Mode Door

ORANGE

Mode Door

GREEN

Mode Door

ORANGE

Mode DoorORANGE

GREEN

06/0106/01

Request to Exit (REX) Button

Case and Back Tamper

The REX button must be located inside the premises to be securedand is used to open the door without the use of a proximity card orPIN code, it is usually located in a convenient location, e.g. Insidethe door or at a receptionist's desk. The function of the REX buttondepends on whether the Lock Strike Relay is programmed for FailSafe Operation or Fail Secure Operation. The door chime in the BL-D40 does not sound when the REX button is used to open the door.

Fail Secure Operation: From the moment the REX button ispressed, the door will be unlocked until the "Lock Strike ReleaseTime" has passed. After this time, the door will be locked even ifthe REX button has not been released.

Fail Safe Operation: From the moment the REX button ispressed, the door will be unlocked until the REX button isreleased, plus the "Lock Strike Release Time". In this case the"Lock Strike Relay" only begins its count down once the REXbutton has been released.

If the case of the controller is opened or the controller is removedfrom the wall, a tamper event is triggered and a coded tampersignal is sent to a BL-D40, PS-X41 Series or PS-X42 Series PowerSupply, or other compatible device.

If the BL-D40 External Sounder , PS-X41 Series or PS-X42 SeriesPower Supplies receive a Tamper Event Signal, they will activate aSiren and if available a Strobe Light. The Siren time can be easilyprogrammed in the AC-A42 from 0 to 9 minutes.

Clearing a tamper event is done by entering a valid User or OpenCode that will open the Lock Strike Output in the current Mode ofOperation. For example, while in Secure Mode, using the OpenCode to clear tamper event will not work because the Open Codedoes not work in Secure Mode. However, applying a Master Codeor Secure Code will clear the tamper event in Secure Mode.

1)

2)

BL-D40 External Sounder

The BL-D40 External Sounder is compatible with the AC-X31, AC-X32, AC-X41, and AC-X42 series Standalone Controllers (For amore up-to-date list of compatible products check the Rosslare WebSite at www.rosslare.com.hk). It is designed to operate indoors andinstalled within the premises to be secured. The Sounder can bepowered by 16V AC or 12 to 24V DC power supply.

The BL-D40 is capable of emitting four different types of alerts bothaudible and visual; Bell, Door Chime, Siren, and Strobe Light.

The Bell always sounds when the controller's doorbell buttonis pressed.

The Door Chime can be programmed to sound whenever thecontroller unlocks the door (the Door Chime does not soundwhen the REX button is used to open the door).

The Siren can be programmed to sound when the case of thecontroller is opened or when the controller is removed from thewall. The controller can also program the length of the Siren inthe BL-D40.

The Controller communicates with the BL-D40 using a codedproprietary Rosslare communications protocol. This provides amore secure link between the Controller and the BL-D40. If the BL-D40 receives any unrecognized codes on its communication line orcommunication between the controller and the BL-D40 are severed,the Strobe with flash repeatedly until the communication problemhas been resolved.

1)

2)

3)


Programming the AC-A42

Programming the AC-A42 is done solely via the unit's keypad drivenProgramming Menu System. To reach the Programming MenuSystem the AC-A42 must first be placed into Programming Mode.See "Entering Programming Mode" on Page 19 for moreinformation.

During the AC-A42's manufacturing process certain codes andsettings are pre-programmed. These settings are the called the"Default Factory Settings".

The table below shows the names of all the AC-A42 Menus. It alsoshows of all the AY-A42's default factory codes and settings.

2580 Change Open Code 1 10852 Change Auxiliary Code 21234 Change Program Code 33838 Change Normal / Secure Code 4N/A Change Normal / Bypass Code 50004 Change Door Release Time 62004 Define Auxiliary Inputs / Outputs

Enroll Proximity Cards, PIN Code or both. 7Delete Proximity Cards Or PIN Code 8Code Assignment with Strike/Auxiliary 9Return to Default Factory Setting 0

You will find a complete description and instructions for each of theabove menu items on the following pages.

Programming Menu

Page 18 06/01AC-A42 Page 19 06/01

Entering Programming Mode

Exiting Programming Mode

1) "#"

2)

Note:

1)

"#"

2)

3)

4) "#"

Press the key for 2 seconds.Mode LED will turn offDoor LED will turn red

Enter your 4-digit ProgrammingCode.

If the Programming Codeis valid the door LED will turngreen and the AC-A42 will be inProgramming Mode.

- The AC-A42 must be in Normal Mode to enter theProgramming Mode.

- The factory default Programming Code is 1234- If a Programming Code is not entered within 5 seconds,

the AC-A42 will return to Normal Mode.

To exit the Programming Mode at any time:

Press the key for 2 seconds.You will hear 3 beeps.The Door LED will be offThe Mode LED will turn green

This indicates that the AC-A42 has returned to Normal Mode.

Wrong entries may reset the controller back to Normal Mode.

While in Programming Mode if no key is pressed for 1 minute theAC-A42 will exit programming mode and return to Normal Mode.

A short press on key may also return the system to NormalMode in certain Programming Modes.

�

�

�

�

�

AC-A42

Mode Door

Mode DoorGREEN

RED

1 2 3 4

Mode Door

GREEN

Menu DescriptionFactorySettings

MenuNumber

Changing the Open Code

Changing the Auxiliary Code

The Open Code is mainly used as a method to quickly test theLock Strike Relay during installation.

The Default Factory Setting for the Open Code is 2580.When the first user is added to the controller, the default OpenCode will automatically be deleted, ready for a new Open Codeto be re-entered.

Enter Programming Mode

Press to enterThe Mode LED will turn red

Enter the new 4-digit code youwish to set as Open Code.

System returns to Normal ModeThe Door LED will turn offThe Mode LED will turn green

- Open Code does not function in Secure Mode.- Wrong entries will return the controller to Normal Mode.- Code 0000 will erase and deactivate the Open Code.

The Auxiliary Code is mainly used as a method to quickly test theAuxiliary Relay during installation.

The Default Factory Setting for the Auxiliary Code is 0852.When the first user is added to the controller, the default AuxiliaryCode will automatically be deleted, ready for a new AuxiliaryCode to be re-entered.

1)

2) "1" Menu 1

3)

4)

Note:

�

�

�

Page 20 06/01AC-A42 Page 21 06/01

1)

2) "2" Menu 2

3)

4)

Note:

1)

2) "3" Menu 3

3)

4)

Note:



Enter the new 4-digit code youwish to set as Open Code.

System returns to Normal ModeYou will hear three beepsThe Door LED will turn offThe Mode LED will turn green

- Auxiliary Code does not work in Secure Mode.- Auxiliary Code only works when the Auxiliary Mode is 1

or 2.- Code 0000 will erase and deactivate the Auxiliary

Code.


Press to enterThe Mode LED will turn green.

Enter the new 4-digit code youwish to set as Programming Code


- Programming Code can not be erased, i.e. the code0000 is not valid and will not erase the ProgrammingCode.

�

�

�

�

�

�

�

�

Changing the Programming Code

AC-A42

Mode Door

Mode DoorGREEN

GREEN

Mode Door

GREEN

Mode Door

GREENRED

? ? ? ?

Mode Door

GREEN

Mode DoorGREENGREEN

? ? ? ?

Mode DoorGREEN

Mode Door

GREEN

Mode Door

GREEN

? ? ? ?

ORANGE

Changing the Normal / Secure Code

Changing the Normal / Bypass Codeand Door Chime Settings

1)

2) "4" Menu 4

3)

4)

Note:

1)

2) "5" Menu 5

3)

a)b)c)d)


Press to enterThe Mode LED will flash red

Enter the new 4-digit code youwish to set as Normal / Secure Code


- When the Auxiliary Mode is 1, 2, 3, or 4 the AuxiliaryInput takes priority over the Normal / Secure Code.

The Normal / Bypass Code is also used to turn the Door Chime offand on.


Press to enterThe Mode LED will flash orange.

Below is a list of the four different ways that the Normal / BypassCode and Door Chime can be programmed.

Disable Bypass Mode - Disable Door ChimeDisable Bypass Mode - Enable Door ChimeEnable Bypass Mode - Disable Door ChimeEnable Bypass Mode - Enable Door Chime

�

�

�

�

�

Page 22 06/01AC-A42 Page 23 06/01

a)

b)

c)

d)

4)

Note:

Disable Bypass Code - Disable Door Chime

Disable Bypass Code - Enable Door Chime

Enable Bypass Code - Disable Door Chime

Enable Bypass Code - Enable Door Chime

Enter the 4-digit code 0000

Enter the 4-digit code 0001

Enter any 4-digit code ending with 0

Enter any 4-digit code not ending with 0


- The Door is only generated when the LockStrike Relay is activated due to a valid code entry.

�

�

�

AC-A42

Mode DoorGREEN

Mode Door

GREEN

Mode Door

GREENRED

? ? ? ?

Mode Door

GREEN

Mode Door

GREEN

Mode Door

GREENORANGE

0 0 0 1

0 0 0 0

? ? ? 0

? ? ? 0

06/01

Defining Auxiliary Inputs/Outputs

1)

2) "6" Menu 6

3)

Auxiliary Mode

Auxiliary Setting

4)

The definitions for the Auxiliary Modes can be found in thetable on the next page.


Press to enterThe Mode LED will flash green

Construct the 4-digit codeusing the instructions below:

In addition to the Lock Strike Relay and Lock Strike REX, theAC-A42 features an Auxiliary Output Relay and an AuxiliaryInput. The Auxiliary Mode defines the function of the AuxiliaryInput and Output.

The Auxiliary Mode also determines if the Auxiliary Output Relayis set for Fail Safe or Fail Secure Operation.

Each of the Auxiliary Modes has a two digit setting that affectshow the Auxiliary Mode functions.

System returns to Normal ModeYou will hear three beepsThe Door LED will turn off.The Mode LED will turn green

�

�

�

�

Auxiliary Mode

Auxiliary Settings

AC-A42

Mode Door

GREEN

Mode Door

GREENGREEN

2 ? ? ?

Mode Door

GREEN

Au

xilia

ryM

od

e

Au

xilia

ryM

od

eQ

uic

kR

efe

ren

ce

Gu

ide

RE

X-2

Valid

Code

or

RE

X-2

N.O

.01

to99

Aux.R

ela

yR

ele

ase

Tim

e00

Aux.R

ela

yToggle

s

Norm

al/S

ecure

Valid

Code

N.O

.01

to99

Aux.R

ela

yR

ele

ase

Tim

e00

Aux.R

ela

yToggle

s

Norm

al/S

ecure

Bell

Button

N.O

.01

to99

Aux.R

ela

yR

ele

ase

Tim

e00

Aux.R

ela

yToggle

s

Norm

al/S

ecure

Tam

per

Event

N.C

.01

to99

Aux.R

ela

yR

ele

ase

Tim

e00

Aux.R

ela

yactivate

dby

Tam

per

Norm

al/S

ecure

DirectS

hunt

N.O

.00

to99

ShuntT

ime

Door

Monitor

Shunt

N.C

.00

to99

Maxim

um

ShuntT

ime

Door

Monitor

Forc

ed

Door

N.C

.00

to99

Forc

ed

Dela

y

Door

Monitor

Door

Aja

rN

.C.

00

to99

Aja

rD

ela

y

For

more

info

rmation

and

the

definitio

ns

ofth

ese

term

sre

fer

toth

eglo

ssary

on

Page

36.

0 1 2 3 4 5 6 7

*Au

xilia

ryIn

pu

tA

uxilia

ryO

utp

ut

Acti

vate

dO

nA

uxilia

ryS

ett

ing

sA

ux.

Rela

y(A

lltim

es

and

dela

ys

are

inseconds)

***

**

*

*

*

*

*

06/01

Enrolling Primary & Secondary Codes

Primary Codes

Secondary Codes

Enrolling Primary and Secondary Codes

- Primary Codes can only be enrolled to an empty User Slot, i.e aslot where there is no existing Primary Code.

- Primary Codes must be unique, i.e. one users Primary Codemay not be the same as another users Primary Code.

- Primary Codes cannot be the same as any system codes, suchas the Normal / Secure Code or Open Code.

- Users who hold a Primary Code can gain entry only duringNormal Mode.

- Secondary Codes can only be enrolled to User Slot that alreadyhas a Primary Code enrolled but no Secondary Code.

- Secondary Codes do not have to be unique, i.e. multiple userscan all hold the same Secondary Code.

- Secondary Codes cannot be the same as any system codes,such as the Normal / Secure Code or Open Code.

- Users who hold Secondary Codes can gain entry in any Modeof Operation.

There are two methods to enroll Primary and Secondarycodes, the Standard Method and the Code Search Method.

A. The Standard Method is mainly used when the User Slotnumber for the user you wish to program is known. You canprogram both Primary and Secondary Codes using theStandard method. (See Enrolling Users with the StandardMethod on Page 28)

B. The Code Search Method is mainly used when enrolling ausers Secondary Code and the User Slot Code is unknown.The Code Search method only works if a users Primary Codeis already enrolled but the Secondary Code is not. (SeeEnrolling Users with the Code Search Method on Page 29)

AC-A42

Setting Fail Safe/Secure OperationSetting Tamper Siren Time

Setting the Lock Strike Release Time

1)

2) "6" Menu 6

3)

"0"

"1"

4)


Press to enterThe Mode LED will flash green

Construct the 4-digit codeusing the instructions below:

For Fail Secure Operation the firstdigit should beFor Fail Safe Operation the firstdigit should be

Tamper Siren Time, enter anynumber from 1 to 9 minutes.

Enter the number of seconds from(1 to 99 seconds) that you wantthe Lock Strike to be released.

For example 0 5 1 2 means Fail Secure Operation, with a 5minute Tamper Siren Time, and a 12 second Lock Strike releasetime.

System returns to Normal ModeYou will hear three beepsThe Door LED will turn off.The Mode LED will turn green

�

�

�

�

First Digit

Second Digit

Third and Fourth Digit

Page 26 06/01AC-A42

Mode Door

GREEN

Mode Door

GREEN

Mode Door

GREEN

GREEN

? ? ? ?

06/01

Enrolling Secondary Codes using the Code SearchMethod

The Code Search feature enables you to quickly enroll a SecondaryCode to a user who already has a Primary Code.


Press to enterThe Door LED will turn orange

Enter the 3-digit User Slot number 000

The Door LED will flash orange

The controller is now waiting for the Primary Code of the Useryou want to add a Secondary Code to.

.

Present the Proximity Card or enter the 4 Digit PIN Code of thePrimary Code belonging to the user you want to add a SecondaryCode to.

The Mode LED will flash red

If the Primary Code entered is not valid, you will hear a long beepand the AC-A42 will continue to wait for a valid Primary Code.

Present the Proximity Card or enter the 4-digit PIN Code to beused as the Secondary Code.

If the Secondary Code is valid the controller will beep three timesand return to Normal Mode.

If the Secondary Code is invalid the controller will make a longbeep and then the AC-A42 will continue to wait for a validSecondary code to be entered.

1)

2) "7" Menu 7

3)

4)

5)

�

�

�

AC-A42

Enrolling Primary and Secondary Codes using theStandard Method

1)

2) "7" Menu 7

3)

4)

5)

"#"

"#"


Press to enterThe Door LED will turn orange

Enter the 3-digit User Slot numberbetween 001 to 500 that you wish toenroll a Primary or Secondary code to.For example, the User Slot 003 represents User #3.

a. If the selected slot has noPrimary Code, the Mode LEDwill flash green, indicating thatthe controller is ready to accept a Primary Code.

b. If the selected slot already hasa Primary Code but noSecondary Code, the Mode LEDwill flash red, indicating that the controller is ready toaccept a Secondary Code.

c. If the selected slot already has a Primary and SecondaryCode, you will hear a long beep and the controller will returnto Normal Mode.

Present a Proximity Card or enter the 4-digit PIN that you want toassign as the Primary or Secondary Code for this slot number.

If the Proximity Card or PIN that is entered is valid the Mode LEDwill stop flashing and then the controller is ready for you to enterthe next 3 Digit slot number (refer to step 3) that you want toassign a code to, or press the key to move to the next slotnumber (refer to step 4). If you do not wish to continue enrollingcodes, press the key for 2 seconds and the controller willreturn to Normal Mode.

�

Page 28 06/01AC-A42

Mode Door

GREEN

Mode DoorORANGE

? ? ?

Mode Door

GREEN GREEN

Mode Door

RED GREEN

Mode Door

GREEN

Mode DoorORANGE

0 0 0

Mode Door

ORANGE

Mode Door

RED ORANGE

Deleting Primary & Secondary Codes

There are two methods to delete Primary and Secondary codes, theStandard Method and the Code Search Method.

When deleting a User Slot, both the Primary Code and theSecondary code are erased.



Enter the 3-digit User Slotcodes you wish to delete.

The Mode LED will flash redIndicating the controller iswaiting for the ProgrammingCode to confirm the deletion.

If the User Slot is empty you will hear a long beep and theAC-A42 will return to Normal Mode

Enter your Programming Code toconfirm the deletion.

If the Programming Code is valid, you will hear three beepsand the AC-A42 will return to Normal Mode.

If the Programming Code is invalid, you will hear a long beep andthe AC-A42 will return to Normal Mode.

- It is recommended that a record be kept of added anddeleted users so that it will be easier to keep track ofwhich user slots are empty and which user slots are not.

Deleting Primary and Secondary Codes using the StandardMethod

1)

2) "8" Menu 8

3)

4)

Note:

�

�

Page 30 06/01AC-A42 Page 31 06/01

Deleting Primary and Secondary Codes using the Code SearchMethod

1)

2) "8" Menu 8

3)

4)

Note:



Enter the 3-digit User Slot 000


The controller is now waiting for the Primary Code of the Useryou want to delete.

Present the Proximity Card or enterthe 4-digit PIN Code of the PrimaryCode belonging to the user you wantto delete.

The Mode LED will flash red

If the Programming Code is valid, you will hear three beepsand the AC-A42 will return to Normal Mode.

If the Programming Code is invalid, you will hear a long beep andthe AC-A42 will return to Normal Mode.

- It is recommended that a record be kept of added anddeleted users so that it will be easier to keep track ofwhich user slots are empty and which user slots are not.

�

�

�

AC-A42

Mode DoorGREEN

Mode Door

GREEN

Mode Door

ORANGERED

? ? ?

Mode Door

? ? ? ?

ORANGERED

Mode Door

ORANGERED

0 0 0

Mode Door

ORANGERED

? ? ? ?

Mode Door

ORANGERED

Lock Strike Relay and Auxiliary RelayCode Assignment

When a Primary Code is enrolled for any user, that user is assignedrights to activate the Lock Strike Relay when they present a validcode to the controller. The Code Assignment Menu allows you toassign whether the Lock Strike Relay and/or the Auxiliary Relay isactivated when a user enters a valid code

There are two methods to Assign Codes, Standard Method and theCode Search Method.


Press to enterThe Mode LED will turn green

Enter the 3-digit User Slot thatyou want to assign a code to.

The Door LED will flash green

Enter the assignment digit for the current User Slot:

"1" assigns the Lock Strike Relay only"2" assigns the Auxiliary Strike Relay only"3" assigns the Lock Strike and Auxiliary Relay

If the assignment code is validthe Mode LED will stop flashing.

The controller is now waiting for another slot number. Press thekey to go to the next slot or enter a new slot number, or if

you do not wish to continue press the key for 2 secondsand the controller will return to Normal Mode.

Lock Strike Relay and Auxiliary Relay Code Assignment usingthe Standard Method

1)

2) "9" Menu 9

3)

4)

"#""#"

�

�

�

Page 32 06/01AC-A42 Page 33 06/01

Lock Strike and Auxiliary Relay Code Assignment using theCode Search Method

1)

2) "9" Menu 9

3)

4)

5)



Enter the 3-digit User Slot 000


The controller is now waiting for the Primary Code of the useryou want to Code Assign

Present the Proximity Card or enterthe 4-digit PIN Code of the PrimaryCode belonging to the user you wantto assign a code to.

The Mode LED will flash green

Enter the assignment digit for the current User Slot:

"1" assigns the Lock Strike Relay only"2" assigns the Auxiliary Strike Relay only"3" assigns the Lock Strike and Auxiliary Relay

If the assignment digit is valid, you will hear three beeps andthen the controller will return to Normal Mode.

If the assignment digit is invalid, you will hear a long beep andthe controller will wait for another assignment digit to be entered.

�

�

�

AC-A42

Mode Door

GREEN

Mode Door

ORANGEGREEN

? ? ?

Mode Door

ORANGEGREEN

? ? ? ?

Mode Door

ORANGEGREEN

Mode Door

ORANGEGREEN

Mode Door

GREEN

Mode Door

ORANGEGREEN

0 0 0

Mode Door

ORANGEGREEN

Return To Factory Default Settings

Warning:

You must be very careful before using this command!Doing so will erase the entire memory which includesall User and Special Codes, and return all codes totheir factory defaut settings.

1)

2) "0" Menu 0

3)


Press to enterThe Mode LED will flash redThe Door LED will flash red

Enter your 4-digit ProgrammingCode.

If the Programming Code is valid, all memory will be erased,you will hear three beeps and the controller will return toNormal Mode

If the Programming Code is invalid you will hear a long beepand the controller will return to Normal Mode without erasingthe memory of the controller.

�

�

�

�

Page 34 06/01AC-A42 Page 35 06/01

Replacing a lost Programming Code

Replacing a lost Normal / Secure Code

1)

2)

3)

4)

5)

1)

2)

3)

4)

5)

Remove power from the AC-A42

Press the REX button

Apply power to the unit with REX button pressed

Release the REX button

You now have 15 seconds to program a new Programming Codeinto the unit using the initial default code 1234, before thecontroller reverts to the existing code.

Remove power from the AC-A42

Press the REX Button

Apply power to the unit with REX button pressed.

Release the REX Button

You now have 15 seconds to program a new Normal / Securecode into the unit using the initial default code 3838, before thecontroller reverts to the existing code.

Note:

Note:

The AC-A42 must be in Normal Mode otherwise this willnot work. Make sure that the Mode LED is green beforeproceeding.

The AC-A42 must be in Secure Mode otherwise this willnot work. Make sure that the Mode LED is red beforeproceeding.

AC-Q42

Mode Door

GREEN

Mode Door

REDRED

? ? ? ?

Glossary

A

B

C

D

Access Control:

Ajar Delay:

Amplitude Shift Keying (ASK):

ASK:

Auxiliary Input:

Auxiliary Code:

Auxiliary Output:

Back Tamper:

Bypass Code:

Bypass Mode:

Cards:Case Tamper:

Code Assignment:

Direct Shunt:

Default Factory Setting:

Direct Shunt Delay:

Door Bell:

Door Chime:

Primarily refers toa device or set of devices controllingthe entry of people traveling througha door or set of doors.

The time allowed for adoor to be left open before soundingan alert and / or activating theAuxiliary Relay.

Thetype of data communicationsbetween the Proximity Card and theProximity Reader.

An abbreviation of "AmplitudeShift Keying".

The term used forthe programmable input electricalsignal from an external device sucha Door Monitor switch or AuxiliaryREX button.

The four digit codeused to activate the Auxiliary Outputfor test ing purposes dur inginstallation.

The term used forthe Relay Output in the AC-A42 thatmay be programmed to activate upondifferent system events such asTamper, Forced Door Event, DoorAjar, etc.

The electronictamper signal advising the controllerthat the controller has been removedfrom the wall.

The four digit codeused to change the Mode ofOperation of the AC-A42 fromNormal to Bypass Mode or viceversa.

A Mode of Operationwhere door access is not restricted to

valid users. In this mode the doormay be released by anyone pressingthe bell button.

See Proximity CardsThe electronic

tamper signal advising the controllerthat the case has been opened.

The process ofassigning which Output(s) (LockStrike Relay and / or Auxiliary Relay)are to be activated when a valid codeis entered.

The arrangement inwhich an external input (such as adoor monitor) is connected directly tothe Auxiliary Relay allowing theAuxiliary Output to be activated afterthe direct shunt delay elapses. Thisleaves the Auxiliary Input availablefor Normal / Secure mode toggle.

Thesettings that the controller ispreprogrammed with when thecontroller is manufactured.

The delay time(user programmed) used in DirectShunt (See Direct Shunt).

The alert sound activatedwhen the door bell button on the AC-A42 is pressed. (Requires the BL-D40 External Sounder)

The alert soundactivated when the lock strikeunlocks the door after a valid codehas been presented. (Requires theBL-D40 External Sounder)

Page 37 06/01AC-A42Page 36 06/01AC-A42

F

L

M

N

O

P

Fail Safe:

Fail Secure:

Forced Door:

Forced Door Time:

Lock Strike:

Lock Strike Release Time:

Master User:

Mode of Operation:

Normal Mode:

Normal / Bypass Code:

Normal / Secure Code:

Normal User:

Normally Closed:

Normally Open:

Open Code:

Primary Code:

Programming Code:

Programming Mode:

Proximity Cards:

The system setting inwhich a total power loss leaves theconnected door unlocked.

The system setting inwhich a total power loss leaves theconnected door locked.

Adoor which has beenphysically opened without the accesscontrol device having released thelock.

The amount oft ime (user programmed) thecontroller waits in the event of aForced Door before the AuxiliaryOutput is activated.

Term used for theelectronic or electromagnetic doorlock used for locking or unlocking thedoor.

Theamount of time (user programmed)that the Lock Strike remainsunlocked when a valid code isentered.

A user which has aPrimary and Secondary Code whichare the same, and can gain access inany Mode of Operation.

The state ofoperation of the controller. There arethree "Modes": Normal Mode,Bypass Mode, and Secure Mode.

The system setting(Mode of Operation) in which all validusers have access upon presenting avalid Proximity Card or PIN Code(Primary Code).

The fourdigit code used to change thecontrollers Mode of Operation from

Normal to Bypass Mode or viceversa.

The fourdigit code used to change thecontrollers Mode of Operation fromNormal to Secure Mode or viceversa.

A user who only has aPrimary Code and can only gainaccess in Normal Mode.

A relay outputfrom the controller that is activated(closed circuit) under normalconditions.

A relay output fromthe controller that is de-activated(open circui t ) under normalconditions.

The four digit code usedto activate the Lock Strike Relay fortesting purposes during installation.

The unique codeissued to enable access in NormalMode. Users with only primary codesare Normal Users.

The four digitcode required when enteringprogramming mode, deleting users,and resetting the AC-A42 to itsfactory default settings.

The modeused when programming the AC-A42's system settings.

Electronicallynumbered ID badges allocated tosystem users and read by theProximity Card Reader.

08/01

Technical Support

http:///www.rosslare.com.hk/support/

Rosslare Enterprises Ltd.905-912 Wing Fat Industrial Bldg.,12 Wang Tai Road, Kowloon Bay,Hong Kong.

Tel: (852) 2795 5630Fax: (852) 2795 1508E-mail: [email protected]

Rosslare Security Products S.r.lVia F.lli Gabba 5, 20121 Milano, Italy


[email protected]

Rosslare NAPDCSuite 238, 200 East Howard Street,Des Plaines, IL 60018USA


International Web Site:

Asia, Australia, & South America

Europe, Russia, Middle East, Africa

United States and Canada

:

:

:

AC-A42Page 38 06/01

R

S

TRelay:

REX:

Request To Exit (REX):

Secondary Code:

Secure Mode:

Secure User:

Shunt:

Shunt Delay:

Strike:

Tamper Siren:

Tamper Siren Time:

Terminal Block:

An electronically controlledswitch used for providing an OpenCircuit or Closed Circuit output toexternal devices.

An abbreviation of "RequestTo Exit".

Refers to abutton which can release the doorfrom inside. Commonly located at thereception desk, or near a door as anemergency door release.

An additionalcode issued to enable access inSecured Mode. Users with non-identical Primary and SecondaryCodes are Secure Users. Users withidentical Primary and SecondaryCodes are Master Users.

The system setting(Mode of Operation) in which onlyvalid Secure and Master Users haveaccess upon presenting a valid code.

A user which has aPrimary Code and Secondary Codethat are non-identical, and can gainaccess in any Mode of Operation.

The arrangement in which anexternal input (such as a doormonitor) is connected directly to theAuxiliary Input, allowing the auxiliaryoutput to be activated after the ShuntDelay elapses. The auxiliary inputwill be unavailable for Normal /Secure Mode toggle.

Is the delay time (userprogrammed) used in Shunt (SeeShunt).

See Lock Strike

The alert soundactivated when a Back Tamper orCase Tamper event occurs.(Requires the BL-D40 ExternalSounder)

The time (userprogrammed) that the Tamper Sirenwill sound when activated.

The rectangularconnectors on the PCB used toattach wiring from external devices.

AC-A42

aca42 instructionmanual100801

Documents