about page - hydrasearch commercial · 2018. 8. 6. · as a subsidiary of dixon valve, a leading...
TRANSCRIPT
410-643-8900 www.hydrasearchcommercial.com
410-643-8900 www.hydrasearchcommercial.com
About PageSince its inception in 1962, Hydrasearch Company, Inc. has been involved in the development and manufacturing of fluid systems and components utilized in demanding military and commercial applications. Founded in Annapolis, Maryland, home of the United States Naval Academy, Hydrasearch quickly established a close connection to our nation’s defense through a commitment to making excellent quality a constant in both our products and our services.
As a subsidiary of Dixon Valve, a leading innovator in the hose coupling industry for over 100 years, Hydrasearch has grown to expand its product line, as well as its customer base, dramatically. In 1994, the company relocated to Stevensville, Maryland. Then in 2016 Hydrasearch moved once again into the building that they are currently located.
The scope of Hydrasearch’s product offerings extends wide across the marine industry. Our products can be found on submarines, surface ships, helicopters, fixed-wing aircraft, and ground equipment across the globe. In 2010, Hydrasearch merged with Buck Algonquin Marine Hardware, further increasing the span of its offerings to meet consumer requirements in pleasure craft and recreational boating. In 2016, the company acquired two new lines: Arctic Steel Water Strainers and Pro-Mar Maritime Venting Solutions. These acquisitions allowed Hydrasearch to fill gaps in its base of offerings and refine its supplier efforts in the commercial and workboat sectors of the industry.
Through all of our growth and development, Hydrasearch has remained consistent in its allegiance to quality and customer satisfaction. We look forward to continuing to grow and improve to provide the best service possible for our customers throughout the industry.
CapabilitiesOur product offerings include: vent check valves, raw water strainers, deck drains & sounding tube deck fittings, suction strainer boxes & bellmouths, full cast stainless steel rudders, and 100R5 hydraulic fittings. Many of our products are ABS approved. We proudly supply our hardware into the Workboat industry, including Offshore Support Vessels (OSV), offshore oil rigs, tugs, ferries, cargo vessels, barges, and defense vessels.
Our current location in Stevensville houses our production, warehouse, and administration in a 65,000-sq. ft. open and collaborative environment. This allows for increased efficiency in production and energy use, while also offering space for further expansion.
We maintain a mature quality control process that helps differentiate Hydrasearch from others in the marine hardware industry. As a preferred vendor to the US Navy, we have a strong QMS System. Driven CMM, in house material analyzer, bore scopes, and many other state of the art tools to ensure quality products.
Various Freight Programs that allow for reduced freight cost based on shipment necessities.
Extensive Engineering Support• Rapid Prototyping
• 3D Printing in House
• In-House Chemical Analysis for Metals
• FEA Analysis
• Flow Simulation
• Modern Machine Shop (12 Machines)
• CMM Measuring Capabilities
• Multiple CAD Software Support
• Full Staffed Quality Department
• Solidworks Capabilities
410-643-8900 www.hydrasearchcommercial.com
Model Number Cross Reference
Product Hydrasearch TateAndale
JohnGjerde KPM Wager Winel Winteb Pres-Vac
Inverted Vent Valve PM-1 52-20 Aero 1.6 1027 1700 ---WIKO5000
SO
Inverted Vent Valvewith Closure
PM-1-C 52-25 --- 1027 1750 --- --- SOC
SteelAir Pipe Head
APH --- Aero 1.1 --- 1500 RM --- M4
AluminumAir Pipe Head (Round)
APH-A --- HIDE 1 --- --- CMWIN2000
HAIS---
Deck Drains DD 60-100 --- 1016 134 --- --- ---
2:1 Ratio Deck Drain DD21 60-140 --- --- 136 --- --- ---
Heavy WalledDeck Drains
DDXH 60-150 --- 1023 246 --- --- ---
Sounding Tubes ST 58-60/61 --- 1009-M 133 --- --- ---
Product Hydrasearch Aeroquip Parker
Hydraulic Fittings 100R5 411 Series 23 Series
Hydraulic Hose 3H-8794100R5, 302A, 303, 1503, 1540, 2580,2651, FC234, FC300, FC321, FC350
FC355, FC558, FC802213, 285
Size (inches) Series Designation Material Connection
1.5” - 12”
PM1
APH
DD
DD21
DDXH
SSB
SBM
ST
Inverted Vent Valve
Air Pipe Head
Alum Air Pipe Head
2:1 Ratio Deck Drain
Heavy Wall Deck Drain
Suction Box Strainer
Suction Bell Mouth
Sounding Tube
GS
SS
B
A
Gal. Steel
Stainless Steel
Bronze
Aluminum
T
W
S
F
SIL
Threaded
Butt-weld
Socketweld
Flanged
Sil-brazed
The above numbering convention covers standard items. Any non-standard item (i.e. different float material, add-on closing device, etc.) will have
additional extensions on the part number
2 - PM1 - GS - TSize (inches)
Series Designation Material
Connection
Table of Contents Aluminum Air Pipe Heads Steel and SS Air Pipe HeadsPage 7 - 8
Deck Drains
Arctic Steel Sea Water Strainers
Page 20 - 22
Sounding Tubes Brass Pipe Caps
Suction StrainersPage 19
Suction BellmouthsPage 18
Spring Loaded Check Valves
Page 23
Cast Iron Threaded Foot Valves
Global Angle ValvesPage 24
AFFF / Water Fog Nozzles Straub Couplings
100R5 Hydraulic Fittings
Electrically Actuated Ball Valves AQ22 Rudders
Page 29 - 30 Page 27 - 28
Nozzles(Fog and Washdown)
Page 24
Page 26
Wye Valve 1/4 Turn Ball Type
Inverted Vent Check Valves
Page 35
Flange and Metric Flange Dimmensions
Fraction to DecimalConversions
Notes
Page 5- 6
Page 17
Page 23
Page 25
Page 31
Page 36 - 38
Page 9 - 14 Page 15 - 16 Page 17
Page 32 Page 33 - 34
410-643-8900 www.hydrasearchcommercial.com
410-643-8900 www.hydrasearchcommercial.com
Aluminum Air Pipe HeadsAPH-A Series
Product Specifications
Part Number A (Size) B C D E Weight (lbs.)
2-APH-A-F-R 2 8.625 5.500 6.000 6.750 7
2.5-APH-A-F-R 2.5 9.250 6.000 7.000 7.625 9
3-APH-A-F-R 3 10.500 6.500 7.500 8.750 11
4-APH-A-F-R 4 12.375 8.000 9.000 10.500 16
5-APH-A-F-R 5 14.750 10.000 10.000 12.250 25
6-APH-A-F-R 6 16.250 11.625 11.000 13.250 33
8-APH-A-F-R 8 21.250 14.625 13.500 17.250 56
10-APH-A-F-R 10 27.250 18.125 16.000 22.250 104
12-APH-A-F-R 12 31.000 22.125 19.000 25.250 151
Designed to prevent seawater from entering tanks, while allowing air or vapor from within the tank to escape when the tank is being filled, and take in air when the tank is being discharged. Tank Vents are also needed for tanks in the storage mode to allow them to “breathe”.
The vertically oriented, slim-lined design reduces weight and eliminates the need for a return bend (gooseneck) saving you valuable deck space.
Corrosion resistant flame screens are also included to provide ignition protection when venting fuel oil tanks.
Flange holes are slotted to accommodate ANSI B16.5 and DN PN10/16 flange dimensions
• Slotted flange holes fit both ANSI and PN10/16 flange mounts
• Intake slots positioned to keep float out of flow stream
External Housing
• Designed to maximize low pressure sealing• Oil and Fuel Resistant
Nitrile Seal (Buna-N)
• HDPE Valve Float (Full Round)
Aluminum Air Pipe HeadsAPH-A Series
• 30 Mesh• Easily accessible for cleaning or replacement• Unique design allows for closing option with screen in
place
Flame / Insect Screen
• Top mounting for easy accessValve Cap
* Closing Device (Optional)
• Designed for easy replacement of valve sealValve Seal Retaining Ring
All Dimensions in Inches
5 6
410-643-8900 www.hydrasearchcommercial.com
410-643-8900 www.hydrasearchcommercial.com
Air Pipe HeadsAPH Series
Designed to prevent seawater from entering tanks, while allowing air or vapor from within the tank to escape when
the tank is being filled, and take in air when the tank is being discharged. Tank Vents are also needed for tanks
in storage mode to allow them to “breathe”.
The Air Pipe Heads do not require a “gooseneck” pipe, reducing valuable weight and deck space requirements.
Corrosion resistant flame screens are also included to provide ignition protection when venting fuel oil tanks.
Flange holes are slotted to accommodate ANSI B16.5 and DN PN10/16 flange dimensions
Product Specifications Max Inlet Air Speed*
Flow Rate** at 3.625 PSI
Part Number A (Size) B C D E F G Weight (m/s) (m3/hr) (GPM)2-APH-GS-F-C 2 10.00 7.00 6.25 8.75 4.00 3.00 32 36 261 150
2.5-APH-GS-F-C 2.5 10.25 7.00 6.25 9.00 4.00 3.50 34 22 251 1603-APH-GS-F-C 3 12.25 9.00 8.75 11.00 5.75 3.75 53 27 441 3154-APH-GS-F-C 4 12.50 9.00 8.75 11.00 5.75 3.75 58 15 447 325
Fabricated5-APH-GS-F 5 15.63 11.38 11.00 14.00 6.50 5.00 90 19 1079 5406-APH-GS-F 6 18.00 13.50 14.00 16.00 7.50 5.50 121 24 1973 7808-APH-GS-F 8 22.50 16.50 16.00 20.00 9.50 6.75 195 27 3924 1410
10-APH-GS-F 10 24.50 20.50 21.75 21.75 12.50 8.00 280 33 7476 190012-APH-GS-F 12 29.00 23.50 25.75 25.75 13.50 9.50 365 26 8582 2700
• Galvanized Steel• (ASTM-A-123)• 316SS
Material Options
• 304SS• Polyethylene (PE)
Float
• Threaded (NPT)• Flanged ANSI/DN• PN 10/16• Butt-weld• Socket Weld
Connections
** Water Pumped through the Air Pipe Head
ABS Type Approved Air Pipe HeadsAPH Series
• Investment Casting (2”- 4”)• Recessed cap design
eliminates catch points(Fabricated)
External Housing
• Removeable for ease of cleaning and inspection
Internal Housing
• Flange Connection is standard. Modifications can be made to suit your needs
Connection
• Seamless, polished, Stainless Steel
• HDPE
Valve Float (Full Round)
• Easily accessible for cleaning or replacement
Flame / Insect Screen
• Downward facing design aids in the containment of overflows
Valve Cover
• Designed to maximize low pressure sealing• Oil and Fuel Resistant
Nitrile Seal (Buna-N)* Closing Device (Optional)
All Dimensions in Inches
7 8
410-643-8900 www.hydrasearchcommercial.com
410-643-8900 www.hydrasearchcommercial.com
Inverted Vent Check ValvesPM-1 Series Full Float
The PM-1 series is designed to prevent seawater from entering tanks, while allowing air or vapor from within the tank to escape when the tank is being filled, and take in air when the tank is being discharged. Tank Vents are also needed for tanks in storage mode to allow them to “breathe”.
The classic inverted design (Gooseneck) offers the simplest means for your venting requirements. Corrosion resistant flame screens are also included to provide ignition protection when venting fuel oil tanks.
Hydrasearch’s innovative design reduces the number of spare parts making disassembly and inspection faster and easier than other valves on the market.
* Air Intake tested with PE float (lightest float)**Water pumped through the Vent Check Valve
• Galvanized Steel• 316SS• B62 Bronze• 535 Aluminum
Material Options
• Threaded• Flanged• Butt-weld
Connection Options
• 304SS• PE (Polyethylene)
Float Options
• 1.5” through 4• HDPE
Sizes
ABS Type Approved
Product Specifications Max Inlet Air Speed*
Flow Rate** at 2.0 PSI
A (Size) B C D E F G Weight Flanged Weight (m/s) (m3/hr) (GPM)
1.5 4.625 4.000 4.750 5.000 1.500 .500 5 8 27 109 56
2 6.125 5.000 6.375 6.000 2.000 .500 9 12 42 306 95
2.5 6.250 5.500 6.625 7.000 1.875 .500 10.5 17.5 26 291 190
3 7.500 6.500 7.938 7.500 2.000 .500 15 22.5 19 315 205
4 8.875 8.000 9.313 9.000 2.500 .500 23 33.5 25 722 335
Inverted Vent Check ValvesPM-1 Series Full Float
• 4 guide ribs assure proper sealing (Required by ABS)
• Recessed cap design eliminates catch points
External Housing
• Designed to maximize low pressure sealing
• Oil and Fuel Resistant
Nitrile Seal (Buna-N)
• Seamless, polished, Stainless Steel
• HDPE
Valve Float (Full Round)
• Easily accessible for Cleaning or replacement
Flame / Insect Screen
• Designed to eliminate the need for a spacer ring and protective screen
Valve Cap
• Innovative design is simple and cost effective
• No additional hardware required
Closing Device (Optional)
To Close - Push up, Turn clockwise until T-handle locks in place (1/4 turn)To Open - Press up, Turn Counter clockwise until T-handle stops (1/4), pull down
All Dimensions in Inches
Weights based on Galvanized Steel and may vary with different material
9 10
410-643-8900 www.hydrasearchcommercial.com
410-643-8900 www.hydrasearchcommercial.com
Inverted Vent Check ValvesPM-1 Series Half Float
The half float design is the big brother to our full float design. The classic inverted design (Gooseneck) offers the simplest means for your venting requirements. Corrosion resistant flame screens are also included to provide ignition protection when venting fuel oil tanks.
Advantages to Hydrasearch’s innovative design
• Rugged construction and increased durability• Reduced number of spare parts make disassembly and inspection faster
and easier than other valves on the market.• Unique Closing Device lowers the cost and saves time by simply lifting the
float into the checked position and locking it in place with a quarter turn.• We have “flipped the float” allowing for improved sealing ability.
Product Specifications Max Inlet Air Speed*
Flow Rate** at 2.0 PSI
A (Size) B C D E F G Weight Flanged Weight (m/s) (m3/hr) (GPM)
5 7.75 10.13 8.25 10.00 3.50 1.00 29 43 10 470 690
6 8.50 11.13 9.00 11.00 3.50 1.00 35 52 9 560 890
8 10.00 14.13 10.75 13.50 3.50 1.00 54 82 8 945 1520
10 12.50 17.00 13.25 16.00 4.25 1.00 90 127 9 1710 2000
12 14.50 21.00 15.75 19.00 5.00 1.00 138 195 9 2495 3500
• Galvanized Steel• 316SS• B62 Bronze• 535 Aluminum
Material Options
• Threaded• Flanged• Butt-weld
Connection Options
• 304SS• PE (Polyethylene)
Float Options
• 5” through 12”Sizes
ABS Type Approved Inverted Vent Check ValvesPM-1 Series Half Float
• 4 guide ribs assure proper sealing (Required by ABS)
• Recessed cap design eliminates catch points
External Housing
• Designed to maximize low pressure sealing
• Oil and Fuel Resistant
Nitrile Seal (Buna-N)
• Seamless, polished, Stainless Steel
• HDPE
Valve Float (Half Round)
• Easily accessible for Cleaning or replacement
Flame / Insect Screen
• Designed to eliminate the need for a spacer ring and protective screen
Valve Cap
• Innovative design is simple and cost effective
• No additional hardware required
Closing Device (Optional)
• Float Arrangement (Flat side up) allows for improved sealing efficiency compared to traditional arrangements
To Close - Push up, Turn clockwise until T-handle locks in place (1/4 turn)To Open - Press up, Turn Counter clockwise until T-handle stops (1/4), pull down
All Dimensions in Inches
* Air Intake tested with PE float (lightest float)**Water pumped through the Vent Check Valve
Weights based on Galvanized Steel and may vary with different material
1211
410-643-8900 www.hydrasearchcommercial.com
410-643-8900 www.hydrasearchcommercial.com
Inverted Vent Check Valve Part Number ReferenceConnecion
Type Pipe Size BronzePart #
Galvanized SteelPart #
Stainless SteelPart #
Aluminum Part #
W/ Closing Device
Threaded
1.5”w/PE Float
1.5-PM1-B-T1.5-PM1-B-T(P)
1.5-PM1-GS-T1.5-PM1-GS-T(P)
1.5-PM1-SS-T1.5-PM1-SS-T(P)
1.5-PM1-A-T1.5-PM1-A-T(P)
Add “-C” ToListedPart
Number
2”w/PE Float
2-PM1-B-T2-PM1-B-T(P)
2-PM1-GS-T2-PM1-GS-T(P)
2-PM1-SS-T2-PM1-SS-T(P)
2-PM1-A-T2-PM1-A-T(P)
2.5”w/PE Float
2.5-PM1-B-T2.5-PM1-B-T(P)
2.5-PM1-GS-T2.5-PM1-GS-T(P)
2.5-PM1-SS-T2.5-PM1-SS-T(P)
2.5-PM1-A-T2.5-PM1-A-T(P)
3”w/PE Float
3-PM1-B-T3-PM1-B-T(P)
3-PM1-GS-T3-PM1-GS-T(P)
3-PM1-SS-T3-PM1-SS-T(P)
3-PM1-A-T3-PM1-A-T(P)
4”w/PE Float
4-PM1-B-T4-PM1-B-T(P)
4-PM1-GS-T4-PM1-GS-T(P)
4-PM1-SS-T4-PM1-SS-T(P)
4-PM1-A-T4-PM1-A-T(P)
5”w/PE Float
5-PM1-B-T5-PM1-B-T(P)
5-PM1-GS-T5-PM1-GS-T(P)
5-PM1-SS-T5-PM1-SS-T(P)
5-PM1-A-T5-PM1-A-T(P)
6”w/PE Float
6-PM1-B-T6-PM1-B-T(P)
6-PM1-GS-T6-PM1-GS-T(P)
6-PM1-SS-T6-PM1-SS-T(P)
6-PM1-A-T6-PM1-A-T(P)
8”w/PE Float
8-PM1-B-T8-PM1-B-T(P)
8-PM1-GS-T8-PM1-GS-T(P)
8-PM1-SS-T8-PM1-SS-T(P)
8-PM1-A-T8-PM1-A-T(P)
Connection Type Pipe Size Bronze
Part #Galvanized Steel
Part #Stainless Steel
Part #Aluminum
Part #W/ Closing
Device
Butt-Weld
1.5”w/PE Float
1.5-PM1-GS-W1.5-PM1-GS-W(P)
1.5-PM1-SS-W1.5-PM1-SS-W(P)
1.5-PM1-A-W 1.5-PM1-A-W(P)
Add “-C” ToListedPart
Number
2”w/PE Float
2-PM1-GS-W2-PM1-GS-W(P)
2-PM1-SS-W2-PM1-SS-T(P)
2-PM1-A-W 2-PM1-A-W(P)
2.5”w/PE Float
2.5-PM1-GS-W2.5-PM1-GS-W(P)
2.5-PM1-SS-W2.5-PM1-SS-W(P)
2.5-PM1-A-W 2.5-PM1-A-W(P)
3”w/PE Float
3-PM1-GS-W3-PM1-GS-W(P)
3-PM1-SS-W3-PM1-SS-W(P)
3-PM1-A-W 3-PM1-A-W(P)
4”w/PE Float
4-PM1-GS-W4-PM1-GS-W(P)
4-PM1-SS-W4-PM1-SS-W(P)
4-PM1-A-W 4-PM1-A-W(P)
5”w/PE Float
5-PM1-GS-W5-PM1-GS-W(P)
5-PM1-SS-W5-PM1-SS-W(P)
5-PM1-A-W 5-PM1-A-W(P)
6”w/PE Float
6-PM1-GS-W6-PM1-GS-W(P)
6-PM1-SS-W6-PM1-SS-W(P)
6-PM1-A-W 6-PM1-A-W(P)
8”w/PE Float
8-PM1-GS-W8-PM1-GS-W(P)
8-PM1-SS-W8-PM1-SS-W(P)
8-PM1-A-W 8-PM1-A-W(P)
10”w/PE Float
10-PM1-GS-W10-PM1-GS-W(P)
10-PM1-SS-W10-PM1-SS-W(P)
10-PM1-A-W 10-PM1-A-W(P)
12”w/PE Float
12-PM1-GS-W12-PM1-GS-W(P)
12-PM1-SS-W12-PM1-SS-W(P)
12-PM1-A-W 12-PM1-A-W(P)
Inverted Vent Check Valve Part Number ReferenceConnecion
Type Pipe Size BronzePart #
Galvanized SteelPart #
Stainless SteelPart #
Aluminum Part #
W/ Closing Device
Socketweld
1.5”w/PE Float
1.5-PM1-B-SIL1.5-PM1-B-SIL(P)
1.5-PM1-GS-S1.5-PM1-GS-S(P)
1.5-PM1-SS-S1.5-PM1-SS-S(P)
1.5-PM1-A-S1.5-PM1-A-S(P)
Add “-C” ToListedPart
Number
2”w/PE Float
2-PM1-B-SIL2-PM1-B-SIL(P)
2-PM1-GS-S2-PM1-GS-S(P)
2-PM1-SS-S2-PM1-SS-S(P)
2-PM1-A-S2-PM1-A-S(P)
2.5”w/PE Float
2.5-PM1-B-SIL2.5-PM1-B-SIL(P)
2.5-PM1-GS-S2.5-PM1-GS-S(P)
2.5-PM1-SS-S2.5-PM1-SS-S(P)
2.5-PM1-A-S2.5-PM1-A-S(P)
3”w/PE Float
3-PM1-B-SIL3-PM1-B-SIL(P)
3-PM1-GS-S3-PM1-GS-S(P)
3-PM1-SS-S3-PM1-SS-S(P)
3-PM1-A-S3-PM1-A-S(P)
4”w/PE Float
4-PM1-B-SIL4-PM1-B-SIL(P)
4-PM1-GS-S4-PM1-GS-S(P)
4-PM1-SS-S4-PM1-SS-S(P)
4-PM1-A-S4-PM1-A-S(P)
5”w/PE Float
5-PM1-B-SIL5-PM1-B-SIL(P)
5-PM1-GS-S5-PM1-GS-S(P)
5-PM1-SS-S5-PM1-SS-S(P)
5-PM1-A-S5-PM1-A-S(P)
6”w/PE Float
6-PM1-B-SIL6-PM1-B-SIL(P)
6-PM1-GS-S6-PM1-GS-S(P)
6-PM1-SS-S6-PM1-SS-S(P)
6-PM1-A-S6-PM1-A-S(P)
8”w/PE Float
8-PM1-B-SIL8-PM1-B-SIL(P)
8-PM1-GS-S8-PM1-GS-S(P)
8-PM1-SS-S8-PM1-SS-S(P)
8-PM1-A-S8-PM1-A-S(P)
Connection Type Pipe Size Bronze
Part #Galvanized Steel
Part #Stainless Steel
Part #Aluminum
Part #W/ Closing
Device
Flanged
1.5”w/PE Float
1.5-PM1-B-F1.5-PM1-B-F(P)
1.5-PM1-GS-F1.5-PM1-GS-F(P)
1.5-PM1-SS-F1.5-PM1-SS-F(P)
1.5-PM1-A-F1.5-PM1-A-F(P)
Add “-C” ToListedPart
Number
2”w/PE Float
2-PM1-B-F2-PM1-B-F(P)
2-PM1-GS-F2-PM1-GS-F(P)
2-PM1-SS-F2-PM1-SS-F(P)
2-PM1-A-F2-PM1-A-F(P)
2.5”w/PE Float
2.5-PM1-B-F2.5-PM1-B-F(P)
2.5-PM1-GS-F2.5-PM1-GS-F(P)
2.5-PM1-SS-F2.5-PM1-SS-F(P)
2.5-PM1-A-F2.5-PM1-A-F(P)
3”w/PE Float
3-PM1-B-F3-PM1-B-F(P)
3-PM1-GS-F3-PM1-GS-F(P)
3-PM1-SS-F3-PM1-SS-F(P)
3-PM1-A-F3-PM1-A-F(P)
4”w/PE Float
4-PM1-B-F4-PM1-B-F(P)
4-PM1-GS-F4-PM1-GS-F(P)
4-PM1-SS-F4-PM1-SS-F(P)
4-PM1-A-F4-PM1-A-F(P)
5”w/PE Float
5-PM1-B-F5-PM1-B-F(P)
5-PM1-GS-F5-PM1-GS-F(P)
5-PM1-SS-F5-PM1-SS-F(P)
5-PM1-A-F5-PM1-A-F(P)
6”w/PE Float
6-PM1-B-F6-PM1-B-F(P)
6-PM1-GS-F6-PM1-GS-F(P)
6-PM1-SS-F6-PM1-SS-F(P)
6-PM1-A-F6-PM1-A-F(P)
8”w/PE Float
8-PM1-B-F8-PM1-B-F(P)
8-PM1-GS-F8-PM1-GS-F(P)
8-PM1-SS-F8-PM1-SS-F(P)
8-PM1-A-F8-PM1-A-F(P)
10”w/PE Float
10-PM1-B-F10-PM1-B-F(P)
10-PM1-GS-F10-PM1-GS-F(P)
10-PM1-SS-F10-PM1-SS-F(P)
10-PM1-A-F10-PM1-A-F(P)
12”w/PE Float
12-PM1-B-F12-PM1-B-F(P)
12-PM1-GS-F12-PM1-GS-F(P)
12-PM1-SS-F12-PM1-SS-F(P)
12-PM1-A-F12-PM1-A-F(P)
Sizes 1.5 - 4 Feature a Full Float Sizes 5 - 12 Feature a Half Float Sizes 1.5 - 4 Feature a Full Float Sizes 5 - 12 Feature a Half Float13 14
410-643-8900 www.hydrasearchcommercial.com
410-643-8900 www.hydrasearchcommercial.com
Deck Drain / Sounding Tube Part Number Guide
Product Pipe Size Material Options ConnectionOptions Strainer Example Part
Number
StandardDeck Drain
1.5”
(GS = Galv. Steel)
(SS = 316SS)
(A=Aluminum)
(W = Butt-weld)
(T = Threaded)
(S = Socketweld)
B62 Bronze
(SS = 316 SS)(add - SS to P/N)
1.5-DD-GS-W
2” 2-DD-GS-W
2.5” 2.5-DD-GS-W
3” 3-DD-GS-W
4” 4-DD-GS-W
6” 6-DD-GS-W
Heavy WallDeck Drain
1.5”(GS = Galv. Steel)
(SS = 316SS)
(A=Aluminum)
(W = Butt-weld)
(T = Threaded)
(S = Socketweld)
B62 Bronze
(SS = 316 SS)(add - SS to P/N)
1.5-DDXH-GS-W
2” 2-DDXH-GS-W
2.5” 2.5-DDXH-GS-W
2:1 RatioDeck Drain 2” (GS = Galv. Steel)
(SS = 316SS)
(A=Aluminum)
(W = Butt-weld)
(T = Threaded)
(S = Socketweld)
B62 Bronze
(SS = 316 SS)(add - SS to P/N)
2-DD21-GS-W
3” 3-DD21-GS-W
Product Pipe Size Material Connection Strainer Example Part Number
Sounding Tube1.5”
(SS = Stainless Steel)
(CS = Carbon Steel)
(A = Aluminum)
Socketweld
B62 Bronze
(SS = 316 SS)(add - SS to P/N)
1.5-ST-SS-S
2” 2-ST-SS-S
2.5” 2.5-ST-SS-S
3” 3-ST-SS-S
Deck Drains
Body Materials:Galvanized Carbon Steel
316 Stainless Steel535 Aluminum
Strainer Materials:B62 Bronze
316 Stainless Steel535 Aluminum
Connections:SocketweldButt-weldThreaded
Body Materials:Galvanized Carbon Steel
316 Stainless Steel
Strainer Materials:B62 Bronze
316 Stainless Steel
Connections:SocketweldButt-weldThreaded
8DD Series (Standard) - Size Reference Chart
A (Size) B C D OA Ratio Weight (lbs.)
1.5 3.25 4.50 3.88 2:5:1 4
2 3.25 4.50 3.88 1:4:1 4
2.5 3.75 5.50 4.88 1:6:1 6
3 3.75 5.50 4.88 1:1:1 5
4 3.75 6.50 5.88 1:1:1 8
6 5.00 11.75 10.88 1:3:1 25
DD21 Series (2:1 Ratio) - Size Reference Chart
A (Size) B C D OA Ratio Weight (lbs.)
2 3.75 5.50 4.88 2:5:1 6
3 3.75 6.50 5.88 2:1 8
DDHX Series (Heavy Wall) - Size Reference Chart
1.5 3.88 4.88 4.13 3:1 7
2 4.00 5.75 5.13 3:1 9
2.5 4.25 6.88 6.25 2:5:1 13
Standard & 2:1 Ratio (Series DD & DD21)
Heavy Wall (Series DDXH - With Trap and Baffle)
All Dimensions in Inches
1615
410-643-8900 www.hydrasearchcommercial.com
410-643-8900 www.hydrasearchcommercial.com
Sounding Tubes
Sounding Tubes (ST Series) are designed to provide watertight closing devices which are always accessible under normal operating conditions to enable sounding of the tanks. The ST Series comes standard with 316SS coupling, bronze plug (with tether chain and venting grooves), and a Buna-N (Nitrile) Gasket.
Standard Sizes: 1.5” through 3”
Product Specifications
A (Size) B C D Plug Thread Weight (lb)
1.5 3.25 1.75 2.95 2-11.5 NPSM 4.5
2 3.25 1.75 2.95 2-11.5 NPSM 4.5
2.5 4.75 1.75 4.06 3-8 NPSM 6.5
3 4.75 1.75 4.06 3-8 NPSM 6.5
Pipe CapsProduct Specifications
Size Part Number Material Thread** Weight (lb)
1.5 FC150 Cast Brass NPSH 0.40
2 FC200 Cast Brass NPSH 0.88
2.5 FC250 Cast Brass NPSH 1.19
3 FC300 Cast Brass NPSH 2.65
4 FC400 Cast Brass NPSH 3.55
6 FC600 Cast Brass NPSH 10.94** Thread is compatible with NPSM
Safety Notes• Not intended for Pressure applications
For debris and thread protection only.• WARNING: This product contains a chemical known to
the state of California to cause birth defects or oth-er reproductive harm. Do not use in connection with drinking water. Wash hands after handling.
Coupling• 316 Stainless Steel (Standard)• Carbon Steel• Aluminum
Threaded Plug• Bronze (Standard)• 316 Stainless Steel• Venting Grooves (Allow venting without
fully removing the plug)• Tether Chain
Nitrile Gasket• Oil and Fuel Resistant
T-Wrench• Galvanized Steel (Sold Separately)
Construction• Pin Lug• Chain Included
Avaliable Options• Other sizes, threads, and finishes avali-
able. Consult Hydrasearch for pricing and avaliability.
All Dimensions in Inches
All Dimensions in Inches
Suction Bellmouths
Part Number A (Size) B C D E Weight (lb.)
3-SBM-O-W 3 5 11.750 5.500 .4375 7
4-SBM-O-W 4 6.750 15.250 6.750 .250 13
5-SBM-O-W 5 8.375 19.250 8.250 .625 21
6-SBM-O-W 6 10 23.250 10 .750 34
8-SBM-O-W 8 13.375 30.750 13.750 1 67
10-SBM-O-W 10 16.750 39 16.750 1.250 122
12-SBM-O-W 12 20 45.375 21.375 1.500 174
Application• Designed for use in ships’ bilges and other such tank locations to
help maintain maximum efficiency during final stripping of liquid cargo tanks.
• Prevents vortex and gas formation as well as minimizing hydraulic loss while pumping liquids from holding tanks.
Features• 1:5:1 open area ratio to pipe size while sitting on bottom of the tank• Fully cast 1025 carbon steel• Butt-weld (beveled end) and flanged connections• Standard sizes: 3” through 12”• Flush without shutting down
All Dimensions in Inches
17 18
410-643-8900 www.hydrasearchcommercial.com
410-643-8900 www.hydrasearchcommercial.com
Arctic Steel StrainersWorld Leader In Cast Stainless Steel Water Strainers
Why Arctic Steel strainers are superior to othersAll Arctic Steel water strainers are cast with 2205 stainless steel. This provides an exceptional level of corrosion resistance. Additionally, our strainers undergo an electro polishing process which removes contaminants from the surface exposing the pure stainless steel, providing a rich chromium film, as is evident by the shine of our stainless steel. This gives our already robust strainers a defense against corrosion, superior to others on the market.
• Free standing, base mounted.• Offset inlet and outlet for improved performance• Electropolished AISI 2205 cast stainless steel body• Electropolished stainless steel lid• Secured by 5 wingnuts for safe, quick and easy access. No tools
required.• Swing down eye bolts eliminates need to remove nuts• BSP or NPT Thread available.• 1” thru 1.5” come standard with full height, high impact resistant
ABS basket.• 2” thru 4” come standard with a full height 316 stainless steel basket• Cast anode connection point to combat galvanic corrosion• Drain plug• Lower outlet position allows for applications that require a header
tank or mounting above the waterline
Side In Side Out Range (SISO)
Avaliable Options• Interchanagable polycarbonate lid.• 316 Stainless Steel mounting brackets and extension arms
A Thread Size (Inlet / Outlet)
Weight (lb.)Solid Lid
Flow Rate 1.45 psi US gpm
Flow Rate 14.5 psi US gpm
B Lid Width
C Height
D Body Width
1 - 11 1/2 Female / Female 8 25 85 6 9.3 5.2
1 1/4 - 11 1/2 Female / Female 15 40 126 7.9 10.6 5.2
1 1/2 - 11 1/2 Female / Female 15.4 56 180 7.9 10.6 5.2
2 - 11 1/2 Female / Female 16 89 282 7.9 10.6 5.2
2 1/2 - 8 Female / Female 30 148 483 9.25 14.4 6.5
3 - 8 Female / Female 32.6 228 743 9.25 14.4 6.5
4 - 8 Female / Female 45.2 451 1450 10.7 18.8 8.7ABS Basket standard on 1”, 1.25”, and 1.5” strainer Flow rates calculated using clean ABS basket316 SS Basket standard on 2”, 2.5”, 3”, and 4”
All Dimensions in Inches
Suction Strainer Box (Rosebox Strainer)Suction Strainer Boxes are designed for use in ships’ bilges and other such tank locations which require trash protection for suction pipes and pumps.
The SSB Series Comes Standard with an 11 gauge fabricated galvanized carbon steel housing and stainless steel fasteners.
Material Options: Carbon Steel, 316SS, or AluminumConnection: O.D Compression CollarStandard Sizes: 2” through 12”
Size Reference Chart
Part Number A (Size) B C D E F Weight (lbs.) OA Ratio
2-SSB-GS 2 4.75 6 6 7.50 5.75 5 11:12.5-SSB-GS 2.5 4.75 6 6 7.50 5.75 5 7:13-SSB-GS 3 4.75 6 6 7.50 5.75 5 5:14-SSB-GS 4 9.50 10 10 12 10.50 15 10:15-SSB-GS 5 9.50 10 10 12 10.50 15 6:5:16-SSB-GS 6 9.50 10 10 12 10.50 15 4:5:18-SSB-GS 8 11 18 18 20 12 18 5:7:110-SSB-GS 10 11 18 18 20 12 18 3:6:112-SSB-GS 12 11 18 18 20 12 18 2:5:1
Size Reference ChartPart Number A (Size) B C (Dia.) Thread Weight (lbs.) OA Ratio
RHS20 1.50 4 4.875 NPSM 1.50 6:8:1RHS25 2 4 4.875 NPSM 2.00 3:8:1RHS30 2.50 3.50 6 NPSM 2.25 5:9:1RHS35 3 5 7 NPSM 3.00 5:4:1RHS40 4 5 7 NPSM 3.25 3:1RHS60 6 9.50 9 NPSM 6.25 5:1:1RHS80 8 11.50 11 NPSM 19.50 4:5:1RHS100 10 18 15 NPSM 40.00 5:5:1RHS120 12 24.50 17 NPSM 31.00 5:8:1
Application• Used on the submersed end of suction hose to prevent debris
from entering the pump during operation• Not for compressed air or other compressible gases.
WARNING: This product contains a chemical known to the state of California to cause birth defects or otherreproductive harm. Do not use in connection with drinking water. Wash hands after handling.
Round Hole Strainer
A
B
C
All Dimensions in Inches
All Dimensions in Inches
2019
410-643-8900 www.hydrasearchcommercial.com
410-643-8900 www.hydrasearchcommercial.com
Arctic Steel Part Number Reference
Product Part Number Pipe Size Material Connection Lid Basket
70WS-SISO-100-S 1”
2205 DuplexStainless Steel
Inlet - Threaded(FNPT)
Outlet - Threaded(FNPT)
Solid ABS(Plastic)
70WS-SISO-125-S 1.25”
70WS-SISO-150-S 1.5”
70WS-SISO-200-S 2”
70WS-SISO-250-S 2.5”
70WS-SISO-300-S 3”
70WS-SISO-400-S 4”
70WS-SISO-100-C 1”
2205 DuplexStainless Steel
Inlet - Threaded(FNPT)
Outlet - Threaded(FNPT)
Clear ABS(Plastic)
70WS-SISO-125-C 1.25”
70WS-SISO-150-C 1.5”
70WS-SISO-200-C 2”
70WS-SISO-250-C 2.5”
70WS-SISO-300-C 3”
70WS-SISO-400-C 4”
70WS-BISO-100-S 1”
2205 DuplexStainless Steel
Inlet - Threaded(FNPT)
Solid ABS(Plastic)
70WS-BISO-125-S 1.25”
70WS-BISO-150-S 1.5”
70WS-BISO-200-S 2”
70WS-BISO-250-S 2.5”
Outlet - Threaded(FNPT)
70WS-BISO-300-S 3”
70WS-BISO-400-S 4”
70WS-BISO-600-S 6”
70WS-BISO-100-C 1”
2205 DuplexStainless Steel
Inlet - Threaded(FNPT)
Clear ABS(Plastic)
70WS-BISO-125-C 1.25”
70WS-BISO-150-C 1.5”
70WS-BISO-200-C 2”
70WS-BISO-250-C 2.5”
Outlet - Threaded(FNPT)
70WS-BISO-300-C 3”
70WS-BISO-400-C 4”
70WS-BISO-600-C 6”
Manufactured from the highest quality electropolished 2205 stainless steelArctic Steel water strainers are designed to be superior in every aspect. There is no welding to corrode in these robust one piece cast strainers. The inherent swirl action created by the offset outlet is designed to quickly scavenge air whilst maximizing the used area of the rugged full height basket. The efficient lid design ensures safe, quick and easy access for maintenance. Suitable for marine engines, generators, and A/C units.
• Electropolished AISI 2205 cast stainless steel body• Solid electropolished stainless steel lid• Secured by 5 wing nuts for safe, quick and easy access. No tools
required.• Swing down eye bolts eliminates need to remove nuts.• BSP or NPT threads available• Full height, high impact resistant ABS basket• Cast anode connection point to combat galvanic corrosion
Bottom in Side Out
Avaliable Options• Interchangeable polycarbonate lid.• 316 Stainless Steel mounting brackets and extension arms.• 316 Stainless Steel basket
A Thread Size (Inlet / Outlet)
Weight (lb.)Solid Lid
Flow Rate 1.45 psi US gpm
Flow Rate 14.5 psi US gpm
B Lid Width
C Height
D Body Width
1 - 11 1/2 Male / Female 6.8 37 114 5.6 8.3 3.7
1 1/2 - 11 1/2 Male / Female 7.1 86 272 5.6 8.3 3.7
2 - 11 1/2 Male / Female 13.4 128 427 7.9 10.7 5.5
2 1/2 - 8 Female / Female 13.7 169 569 7.9 10.7 5.5
3 - 8 Female / Female 27.6 257 792 9.25 13.1 6.5
4 - 8 Female / Female 40.8 487 1545 10.7 18.7 8.7
6 - 8 Female / Female 66.8 841 2718 14.2 20.1 12.2ABS Basket standard on 1”, 1.25”, and 1.5” strainer Offer standard with Full height, high impact ABS Basket316 SS Basket standard on 2”, 2.5”, 3”, and 4” Flow rates calculated using clean ABS basket
All Dimensions in Inches
21 22
410-643-8900 www.hydrasearchcommercial.com
410-643-8900 www.hydrasearchcommercial.com
Global Angle Valves
Size 1 1/2” 2 1/2”
A 4.13 5.69
B 3.75 5.00
C (Closed) 6.80 9.00
C (Open) 7.78 10.72
D 2.25 3.19
E 1.81 2.59
Weight (lb) 4.4 9.5
Female Inlet• Male NH outlet• NPT inlet thread only• Aluminum hand wheel• Working Pressure: 300 PSI at 70°F (21°C)• Alloy = Yellow DZR BrassAvaliable finish:• Cast (standard)• Polished = -P• Chrome = -C
AV150-l and AV250-l
Double Female• NPT inlet and outlet only• Aluminum hand wheel• Working Pressure: 300 PSI at 70°F (21°C)• Alloy = Yellow DZR BrassAvaliable finish:• Cast (standard)• Polished = -P• Chrome = -C
AVF150-l and AVF250-l
Wye Valves - 1/4 Turn Ball
Features:• Cast Brass• Rocker lug swivel• Operates easily under high pressure• Handles are not field replaceable• Seal on the ball are field adjustable and field replaceable• Maximum operating pressure: 175 PSI (water only) at 70°F (21°C)
Specification• Meets NSN Specifications # 4210-00-255-0234
Inlet (Female) (2) Outlets (Male) Part # Weight (lb.)
2 1/2” NST (NH) 1 1/2” NPSH S7337S 12.06
2 1/2” with cast finish shown
1 1/2” with cast finish shown
Warning: This product contains chemicals known to the State of California to cause birth defects or other reproductive harm. Do not use in connection with drinking water. Wash hands after handling.
Underwriter’s Listed, Factory Mutual Approved.
All Dimensions in Inches
Cast Iron Threaded Foot Valve
Part Number Material Size Thread Weight (lb.)
DFVS20 Painted Cast Iron 1.50 NPT 3.10
DFVS25 Painted Cast Iron 2 NPT 5.41
DFVS30 Painted Cast Iron 2.50 NPT 6.98
DFVS35 Painted Cast Iron 3 NPT 9.49
DFVS40 Painted Cast Iron 4 NPT 15.52
DFVS60 Painted Cast Iron 6 NPT 37.80
DFVS80 Painted Cast Iron 8 NPT 85.10
Replacement PartsValveStrainerSeat Plate
Safety notes:• Must be installed in the vertical position• For water service only• WARNING: This product contains a chemical known to the State of
California to cause birth defect or other reproductive harm. Do not use in connection with drinking water. Wash hands after handling.
Spring Loaded Check Valves
Warning: This product contains chemicals known to the State of California to cause birth defects or other reproductive harm. Do not use in connection with drinking water. Wash hands after handling.
Features• Soft seat for bubble tight shutoff, spring loaded for fast seating
action• Flow profile designed to minimize head loss• Cracking Pressure: 0.50 PSI• NBR seat• Pressure rating: 1/2” - 2” 400 PSI WOG; 3” - 4” 175 PSI WOG• Temperature range: 10°F to 210°F (-10°C to 100°C)
Part Number Material Size Thread Weight (lb.)BVFS20 Brass 1.50 Female NPT 1.970BVFS25 Brass 2 Female NPT 2.400BVFS35 Brass 3 Female NPT 7.810BVFS40 Brass 4 Female NPT 12.395
Without StrainerCV050 Brass .50 Female NPT 0.3375CV075 Brass .75 Female NPT 0.5200CV100 Brass 1 Female NPT 0.7500CV125 Brass 1.25 Female NPT 1.1800CV150 Brass 1.50 Female NPT 1.6300CV200 Brass 2 Female NPT 2.3400CV300 Brass 3 Female NPT 6.7300CV400 Brass 4 Female NPT 12.080
With StainlessSteel Strainer
WithoutStrainer
All Dimensions in Inches
All Dimensions in Inches
2423
410-643-8900 www.hydrasearchcommercial.com
410-643-8900 www.hydrasearchcommercial.com
U.S. Coast Guard ApprovedAFFF / Water Fog Nozzles
Application• Designed for maximum efficiency with AFFF (Aqueous Film Forming Foams)
or water on shipyard, offshore rigs and industrial applications
Features• Corrosion resistant brass construction• Rubber-like bumper and handle for added protection• Zytel (nylon) horseshoe handle• Double row of molded teeth for excellent fog pattern• Flush without shutting down• Constant gallonage in all fog and straight stream patterns• Combination for and straight stream• Maximum operating pressure: 100 PSI (water / AFFF only) at 70°F (21°C)
Thread Description Fog Flow GPM @ 100 PSI Brass Part Number Approval #
1 1/2 NST (NH) NozzleNozzle w/ pistol grip
9595
CGSN150FCGSN151F
162.027/13/0162.027/14/0
1 1/2 NPSH NozzleNozzle w/ pistol grip
9595
CGSN150SCGSN151S
Gaskets are special order, please call 410.643.8900 for assistance
Thread NST Fog Flow (GPM @ 100 PSI) Brass Part Number
1 1/22 1/2
55108
CGN150NSTCGN250NST
Gaskets are special order, please call 410.643.8900 for assistance
Application• Designed to US Coast Guard specifications for fighting fires with draft water,
required equipment for all commercial vessels under US registry.
Features• Maximum operating pressure: 100 PSI (water / AFFF only) at 70°F (21°C)• Corrosion resistant brass connection• Combination and straight stream for shipboard firefighting• Applicator tips are available, consult Hydrasearch for price and availability
U.S. Coast Guard Approved Fog Nozzles
CGSN151F
CGSN150F
Warning: This product contains chemicals known to the State of California to cause birth defect or other reproductive harm. Do not use in connection with drinking water. Wash hands after handling.
Features• Maximum operating pressure: 100 PSI (water only) at 70°F (21°C)• Delivers 30° - 60° - 90° fog pattern• Shutoff - straight stream - fog• Supplied with bumper• For use with water only
Brass Industrial Wash-down Nozzle
Size Thread 90 Spray GPM @ 100 PSI Weight (lb) Part Number
1 1/2NPSH
NST (NH)88 (+/- 12)88 (+/- 12) 1.400 WDN150
WDN150NST
Features• Shutoff – straight stream – fog• Maximum operating pressure: 100 PSI (water only) at 70°F (21°C)• Brass stem• Material - Polycarbonate• (1) Standard Flow• (2) 120° spray GPM @ 100 PSI
Fog Nozzles
Size Thread 90° Spray GPM @100 PSI Part Number (with Bumper)
Part Number (without Bumper)
3/4 GHT 8.0 FNB75GHT (1,2) - - -3/4 NPS 30.9 FNB75S (2) - - -
1 NPS 11.4 FNB100S (2) FN100S
1 NPS 30.9 HGB100S - - -
1 1/2 NPS 83.6 FNB150S FN150S
1 NST (NH) 11.4 FNB100NST FN100NST
1 NST (NH) 30.9 HGB100NST - - -
1 1/2 NST (NH) 83.6 FNB150NST FN150NST
Warning: This product contains chemicals known to the State of California to cause birth defect or other reproductive harm. Do not use in connection with drinking water. Wash hands after handling
Nozzles
All Dimensions in Inches
All Dimensions in Inches
25 26
410-643-8900 www.hydrasearchcommercial.com
410-643-8900 www.hydrasearchcommercial.com
Straub Grip - LFire - Fence®
The STRAUB FIRE-FENCE combines functional design with the latest technologies. The coupler is based on the reliable and well proven STRAUB coupling system and fulfills IMO (International Maritime Organization) and IACS (International Association of Classified Societies) requirements alike, which have been in force since 1-1-2017.
Even with its flame protection, the coupling is space saving, shows significantly improved crush resistance and, thanks to the innovative design, is also lighter. The new STRAUB-FIRE-FENCE impresses with a modern, patented construction method, while at the same time retaining the well tested characteristics of STRAUB couplings.
Functionality: In the event of a fire, the intumescent* fire protection coating expands, protectively enclosing the coupling. During this process, the coupling retains its full operational capability – without any limitations.
* Under the influence of heat, intumescent materials increase in volume and decrease in density, i.e. the material expands. This produces an isolating heat shield which protects the assembly part.
The Fire Resistant CouplingFor use wherever fire protection is required by law
STRAUB-coupling Protectivemetal layer
Intumescent polymer profile
Application• Suitable for pipes within the lower pressure range.
Features• Joins like or dissimilar pipe materials• Accommodates up to 5° of pipe misalignment• Vary gap between pipe ends• Absorbs vibration, water and hammer sound• Special patented grip ring for superior holding power on hard-surfaced
pipes• 5 year limited warranty• Reusable• EPDM sealing sleeve temperature range: -4°F to 176°F (-20°C to
80°C)• NBR and FKM sleeves available, contact Hydrasearch for information
Materials:• Casing: AISI 316Ti; screws: AISI 316 L; bolts AISI 316 Ti;
Anchoring ring: AISI 301; Sealing sleeve: EPDM standard
Specifications• American Bureau of Shipping (ABS) up to 232 PSI on ¾”- 5”;
188 PSI on 6”; 145 PSI on 8”• Underwriters Laboratories (UL)• National Sanitation Foundation (NSF)• Built to ASTM 1476, Type 2, Class 2 Specification
Pipe OD Range Working Pressure
Coupling Dimensions
Assembled Dimensions
Max. Distance Between Pipe End
316 Ti Stainless Steel
Size Actual Min to Max PSI B C DV KV R Part #
.75 1.05 1.04 to 1.08 670 1.8 0.7 1.7 2.8 0.2 STR20000*
1 1.31 1.31 to 1.35 550 1.8 0.7 2.0 3.0 0.2 STR20100*
1.50 1.90 1.88 to 1.92 440 2.4 1.0 2.6 3.9 0.2 STR20300*
2 2.37 2.35 to 2.40 320 3.0 1.5 3.1 4.3 0.4 STR20450*
2.50 2.87 2.85 to 2.90 450 3.7 1.6 3.9 5.3 0.4 STR20500
3 3.50 3.46 to 3.54 320 3.7 1.6 4.4 5.9 0.4 STR20650
4 4.50 4.46 to 4.54 232 3.7 1.6 5.4 6.7 0.4 STR20900
5 5.50 5.51 to 5.62 232 4.3 2.1 6.5 8.3 0.4 STR21150
6 6.63 6.56 to 6.69 232 4.3 2.1 7.6 9.1 0.4 STR21350
8 8.63 8.54 to 8.71 232 5.6 3.1 9.8 11.6 0.4 STR21400* only has one bolt
Note: All Straub couplings require the correct use of a torque wrench for a safe and proper installation. Straub couplings must be torqued to the specified value as printed on each individual coupling. Failure to do so can result in serious injury or death. Not for steam or refrigerant service
Straub Grip - L, Axial Restraint Pipe Coupling ABS Type Approved
All Dimensions in Inches
27 28
410-643-8900 www.hydrasearchcommercial.com
410-643-8900 www.hydrasearchcommercial.com
AQ-22 RuddersTM represent a major advancement in the marine industry. Designed for boat speeds up to 40 knots, these wedge section rudders are made of high strength and superior corrosion resistant AQ-22 stain-less steel. Seven rudder sizes have been standardized so that a combination of speed and displacement may be accommodated for most all modern boat and yacht designs. This standardization of rudder design results in the economy of large production runs while at the
same time providing custom design benefits.
Stock AQ-22 Rudder Specifications
Rudder Model
Diameter in. (D)
Length in. (L)
Wt. Stock Per Ft. lb./FT.
Rudder Wt. Less Stock lb.
Rudder Length in.
(A)
Stock Location in.
(B)
Rudder Width in.
(C)
Estimated” Rudder Torque 40 Knots
in./lb.I 1.250 15 4.17 19 13.500 6.6875 9.8125 4,400II 1.500 18 6.01 30 16.500 8.250 12 8,100III 1.750 21 8.18 47 19 9.375 13.375 12,200
IV 2.250 24 13.52 82 23.375 11.625 17 22,300V 2.750 30 20.19 125 27 13.375 19.500 34,300VI 4 34 42.71 200 31 15.375 22.375 52,200VII 4.500 38 54.05 275 34.500 17 25 71,900
What Are the Special Features of the AQ-22 Rudder Design?
The AQ-22 Rudders have incorporated a number of features like the hydrodynamic shape that makes it a supe-rior performer throughout the design speed range. The wedge sections were selected to give positive steering forces for a full range of port and starboard rudder angles when operating behind a propeller or in freestream. The rudder continues to generate increasing side forces with rudder angles as high as 25 degrees at 40 knots; a condition where typical air foil section rudders have stalled.
The AQ-22 Rudder is also designed to trail or track in the slip stream should the steering gear fail at high speeds, unlike an airfoil section rudder with a normal stock location which could cause a snap turn during high speed runs should steering failure occur.
In profile, the top trailing edge of the rudder is cut away to minimize ventilation of the rudder during high speed turns. Rudder ventilation may cause a vessel to almost stop turning, even with increasing rudder angles at high speed. When the trailing edge of the AQ-22 Rudder is installed slightly ahead of the transom, ventilation is not likely to occur as might be experienced with rudders having other profiles and section shapes.
The AQ-22 Rudders incorporate hydrodynamic features cast in stainless steel to provide the strength and positive steering control not likely to be found in other designs.
*Rudder torque has been increased 25% to allow for bearing friction.
HIGH STRENGTH - SUPERIOR CORROSION RESISTANCE - EXCELLENT PERFORMANCE
AQ-22 Marine Rudders Rudder Selection
To select the correct AQ-22 rudder, an estimate of the maximum operating speed and displacement of the boat must be determined. If the displacement cannot be determined, boat length parameters for selecting the appropriate rud-der are included in the charts.
The speed at which a boat is typically driven will impact the choice of rudder size. In general, the heavier and slower the boat, the larger the rudder required. Although the rudders have been designed to handle 40 knots, selecting a rudder which is too large will restrict the boat from achieving full speed, and one too small will lead to steering control difficulties.
Typically, a single rudder is required for each propeller. However, there are triple screw craft’s in service operating successfully with one centerline rudder, or with two rudders, one located behind each outboard propeller.
In selecting the length of the rudder stock, consideration must be given to mounting the steering system quadrant or arm at the correct height leaving some room for the installation of emergency steering equipment. If a specific length is required, it must be stated when ordering the rudder. Otherwise, the length noted in the catalog will be supplied.
The charts have been formulated to assist in making the appropriate selection for one, two, or three rudder options. In the event the requirements of a particular boat are outside the parameters of the stock AQ-22 rudders, please contact the manufacturer for further information.
Notes Relative to Tables and Charts
• The numerical value of the stock length (L) has been chosen arbitrarily.
• Rudder weights are estimated.• Rudder torque is included so that the force
required at the tiller arm may be estimated.• Dash lines indicate approximate boat length.• Roman numerals indicate rudder model
recommended.• Consult the manufacturer for rudder require-
ments outside those of stock design.
3029
410-643-8900 www.hydrasearchcommercial.com
410-643-8900 www.hydrasearchcommercial.com
Electrically Actuated 2-Piece Stainless Ball Valve
Part Number SizeDimensions (inches)
OverrideA B C D E
BV2HH-02511 .250 7.79 4.50 2.56 1.40 - - - Standard
BV2HH-03811 .375 7.79 4.50 2.56 1.40 - - - Standard
BV2HH-05011 .500 7.74 4.50 2.95 1.40 - - - Standard
BV2HH-07511 .750 7.84 4.50 3.15 1.75 - - - Standard
BV2HH-10011 1 8.09 4.50 3.54 1.75 - - - Standard
BV2HH-12511 1.250 8.29 4.50 4.33 2.58 - - - Standard
BV2HH-15011 1.500 8.69 4.50 4.72 2.97 - - - - - -
BV2HH-20011 2 11.13 4.50 5.51 2.73 - - - - - -
BV2HH-25011-EP* 2.500 13.72 7.08 7.28 4.68 12.83 Hand Wheel
BV2HH-25011 2.500 10.69 6.06 7.28 4.68 - - - - - -
BV2HH-30011 3 13.72 7.08 8.07 5.44 12.83 Hand Wheel* for 110VAC 2 1/2” with manual override use - EP
Features:2-Piece Stainless Ball Valve• RTFE seats and seals• Blow-out proof stem• Live-loaded stem packing• ISO 5211 mounting pad• Pressure rating:
1/4” - 2” 1000 PSI WOG21/2” - 3” 800 PSI WOG
• Temperature range:- 40°F to 450°F
(- 40°C to 232°C)
Electric Actuator• Powder coated aluminum alloy housing• NEMA 4/4X waterproof and dustproof• Extended duty cycle induction motor• High alloy steel gear train• H - insulation class• Visual position indication• Space heater is standard• Manual override standard: ½” - 1½”• Temperature range: - 41°F to 140°F
(- 40°C to 60°)• ISO 9001, CS, CE and CSA-C US Certified,
RoHS compliant
Caution: Even though there are torque safety factors built into our automated ball valve packages, actual service conditions must also be considered when selecting the proper product for the appropriate application. For example: Severe service conditions such as dirty water, dirty air, all slurries, raw sewage water, oils, and other viscous fluids can have a dramatic affect in raising the torque requirements of ball valves as much as 75% and therefore larger actuators may be required. Please consult Hydrasearch when dealing with these types of applications.
All Dimensions in Inches
100R5 Hydraulic FittingsHydrasearch is now offering 100R5 fittings! These 3-piece, reusable, hydraulic fittings are designed for use with 100R5
hydraulic hose, but can be used with other manufacturer’s hose as well.
• Sizes 1/4” to 1 - 1/2” (sizes -4 to -24) are available (stocking both brass and stainless steel).• These are 37 degree flared JIC fittings. They can be used for a 45-degree connection as well.
These reusable 3-piece fittings are ideal for use in the marine industry because they can be repaired at sea. Unlike crimp fittings, which require an expensive press to install, reusable fittings require minimal tools.
Equal to Aeroquip’s 411 series, Parker’s 23 seriesUse with the following hose: Aeroquip Hoses: 100R5, 302A, 303, 1503,1540, 2580, 2651, FC234, FC300, FC321, FC350, FC355, FC558, FC802; Parker Hoses: 213, 285, 293; Hydrasearch Hose: 3H-8794 I.A.W. MIL-DTL-8794
(Synthetic yarn and wire reinforced hoses)
Size Material Part Number 1/4 316 Stainless Steel CR-48A-04
5/16 316 Stainless Steel CR-48A-053/8 316 Stainless Steel CR-48A-061/2 316 Stainless Steel CR-48A-085/8 316 Stainless Steel CR-48A-103/4 316 Stainless Steel CR-48A-12
1 316 Stainless Steel CR-48A-16
1 1/4 316 Stainless Steel CR-48A-201 1/2 316 Stainless Steel CR-48A-24
Size Material Part Number 1/4 Brass AN-48A-04
5/16 Brass AN-48A-053/8 Brass AN-48A-061/2 Brass AN-48A-085/8 Brass AN-48A-103/4 Brass AN-48A-12
1 Brass AN-48A-16
1 1/4 Brass AN-48A-201 1/2 Brass AN-48A-24
31 32
410-643-8900 www.hydrasearchcommercial.com
410-643-8900 www.hydrasearchcommercial.com
Metric Flanges and DimensionsNOM DIA
(mm) DIN PN6 DIN PN10
DIN PN16
DIN PN25
DIN PN40 JIS 5K JIS 10K JIS 16K JIS 20K JIS 40K
15 D 80 BC 55 H 4 x 11
9565
4 x 14
9565
4 x 14
9565
4 x 14
9565
4 x 14
8060
4 x 12
9570
4 x 15
9570
4 x 15
9570
4 x 15
11580
4 x 19
20 9065
4 x 11
10575
4 x 14
10575
4 x 14
10575
4 x 14
10575
4 x 14
8565
4 x 12
10575
4 x 14
10575
4 x 14
10575
4 x 14
12085
4 x 19
2510075
4 x 11
11585
4 x 14
11585
4 x 14
11585
4 x 14
11585
4 x 14
9575
4 x 12
12590
4 x 19
12590
4 x 19
12590
4 x 19
13095
4 x 19
3212090
4 x 19
140100
4 x 18
140100
4 x 18
140100
4 x 18
140100
4 x 18
11590
4 x 15
135100
4 x 19
135100
4 x 19
135100
4 x 19
140105
4 x 19
40130100
4 x 14
150110
4 x 18
150110
4 x 18
150110
4 x 18
150110
4 x 18
12095
4 x 15
140105
4 x 19
140105
4 x 19
140105
4 x 19
160120
4 x 23
50140110
4 x 14
165125
4 x 18
165125
4 x 18
165125
4 x 18
165125
4 x 18
130105
4 x 15
155120
4 x 19
155120
8 x 19
155120
8 x 19
165130
8 x 19
65160130
4 x 14
185145
4 x 18
185145
4 x 18
185145
4 x 18
185145
4 x 18
155130
4 x 15
175140
4 x 19
175140
8 x 19
175140
8 x 19
200160
8 x 23
80190150
4 x 18
200160
8 x 18
200160
8 x 18
200160
8 x 18
200160
8 x 18
180145
4 x 19
185150
8 x 19
200160
8 x 23
200160
8 x 23
210170
8 x 23
100210170
4 x 18
220180
8 x 18
220180
8 x 18
235190
8 x 22
235190
8 x 22
200165
8 x 19
210175
8 x 19
225185
8 x 23
225185
8 x 23
250205
8 x 25
125240200
8 x 18
250210
8 x 18
250210
8 x 18
270220
8 x 26
270220
8 x 26
235200
8 x 19
250210
8 x 23
270225
8 x 25
270225
8 x 25
300250
8 x 27
150265225
8 x 18
250210
8 x 22
250210
8 x 22
270220
8 x 26
270220
8 x 26
235200
8 x 19
250210
8 x 23
270225
12 x 25
270225
12 x 25
300250
12 x 33
175395255
8 x 18
315270
8 x 22
315270
8 x 22
330280
12 x 26
350295
12 x 30
300260
8 x 23
305265
12 x 23
200320280
8 x 18
340295
8 x 22
340295
12 x 22
360310
12 x 26
375320
12 x 30
320280
8 x 23
330290
12 x 23
350305
12 x 25
350305
12 x 25
405345
12 x 33
250375335
12 x 18
395350
12 x 22
405355
12 x 26
425370
12 x 30
450385
12 x 33
385345
12 x 23
400355
12 x 25
430380
12 x 27
430380
12 x 27
475410
12 x 33
300440395
12 x 22
445400
12 x 22
460410
12 x 26
485430
16 x 30
515450
16 x 33
430390
12 x 23
445400
16 x 25
480430
16 x 27
480430
16 x 27
540470
16 x 39
350490445
12 x 22
505460
16 x 22
520470
16 x 26
555490
16 x 33
580510
16 x 36
480435
12 x 25
490445
16 x 25
540480
16 x 33
540480
16 x 33
585515
16 x 39
400540495
16 x 22
565515
16 x 26
580525
16 x 30
620550
16 x 36
660585
16 x 39
540495
16 x 25
560510
16 x 27
605540
16 x 33
605540
16 x 33
645570
16 x 39
450595550
16 x 22
615565
20 x 26
640585
20 x 33
670600
20 x 36
755670
20 x 42
605555
16 x 25
620565
20 x 27
675605
20 x 33
500645600
20 x 22
670620
20 x 26
715650
20 x 33
730660
20 x 36
795660
20 x 36
655605
20 x 25
675620
20 x 27
730660
20 x 33 D: Flange Diameter BC: Bolt Circle Diameter H: Bolt Holes x Hole Diameter 1 inch = 25.4 mm
Normal Pipe Size
Flange Diameter
A
Flange Thickness
B
Diameter of Raise Face
C
Diameter of Bolt Circle
D
Diameter of Bolt Holes
ENumber of Bolts
Diameter of Bolts
Length of Stud Bolts with 2 Nuts
F
Length of Machine Bolts
G
1 1/2 5 11/16 2 7/8 3 7/8 5/8 4 1/2 2 3/4 2 1/4
2 6 3/4 3 5/8 4 3/4 3/4 4 5/8 3 2 3/4
2 1/2 7 7/8 4 1/8 5 1/2 3/4 4 5/8 3 1/4 3
3 7 1/2 15/16 5 6 3/4 4 5/8 3 1/2 3
4 9 15/16 6 3/16 7 1/2 3/4 8 5/8 3 1/2 3
5 10 15/16 7 5/16 8 1/2 7/8 8 3/4 3 3/4 3 1/4
6 11 1 8 1/2 9 1/2 7/8 8 3/4 3 3/4 3 1/4
8 13 1/2 1 1/8 10 5/8 11 3/4 7/8 8 3/4 4 3 1/2
10 16 1 3/16 12 3/4 14 1/4 1 12 7/8 4 1/2 3 3/4
12 19 1 1/4 15 17 1 12 7/8 4 1/2 4
14 21 1 3/8 16 1/4 18 3/4 1 1/8 12 1 5 4 1/4
16 23 1/2 1 7/16 18 1/2 21 1/4 1 1/8 16 1 5 1/4 4 1/2
Normal Pipe Size
Bore Through
Flange Diameter
Flange Thickness
Diameter of Bolt Circle
Number of Holes
Hole Diameter
1 1/2 1.770 ± .003 5.0625 .4375 3.9375 6 .56252 2.240 ± .003 5.5625 .4375 4.4375 6 .5625
2 1/2 2.750 ± .004 6.125 .500 5.000 6 .56253 3.370 ± .004 6.625 .500 5.000 8 .56254 4.370 ± .004 7.6875 .5625 6.5625 8 .56255 5.420 ± .004 9.0625 .5625 7.8125 10 .68756 6.460 ± .004 10.125 .5625 8.875 12 .68758 8.410 ± .004 12.375 .625 11.0625 14 .6875
10 10.480 ± .004 15.000 .6875 13.4375 15 .812512 12.430 ± .004 17.625 .750 16.0625 18 .8125
Navy Flange DimensionsMIL-PRF-20042
Steel Flange Dimensions
All Dimensions in Inches
All Dimensions in Inches
3433
410-643-8900 www.hydrasearchcommercial.com
410-643-8900 www.hydrasearchcommercial.com
NotesFraction to Decimal Conversions
35 36
410-643-8900 www.hydrasearchcommercial.com
410-643-8900 www.hydrasearchcommercial.com
Notes Notes
37 38